EdgeStar | CWR181SZ | Owner`s manual | EdgeStar CWR181SZ Owner`s manual

Wine Refrigerator
CWR181SZ
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
Important Safety Information
Improper handling can cause serious damage to the EdgeStar wine refrigerator and/or injury to the user. This wine
refrigerator is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other
use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and
other technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of fire, electric shock or injury.
Electrical Safety
 Do not exceed the power outlet ratings.
 It is recommended the wine refrigerator be
connected on its own circuit.
 The unit must be installed in accordance with
state and local electrical codes.
 A standard electrical supply (115 V, 60Hz), that is
properly grounded in accordance with the
National Electrical Code and local codes and
ordinances is required.
 Use outlets that cannot be turned off by a switch
or pull chain.
 Always turn the unit off and unplug it from the
outlet when cleaning.
 Unplug the unit if it is not going to be used for an
extended period of time.
 Do not operate the unit with a power plug missing
the ground plug, a damaged cord or a loose
socket.
 Be sure the wine refrigerator is properly
grounded.
 Never plug or unplug the unit with wet hands.
 Do not bypass, cut or remove the grounding plug.
 Do not use extension cords or power strips with
this unit. You may need to contact your electrician
if it is necessary to use a longer cord or if you do
not have a grounded outlet. Do not modify the
power cord’s length or share the outlet with other
appliances.
 Do not start or stop the unit by switching the
circuit’s power on and off.
 If the power cord is damaged, it must be replaced
by the manufacturer or a qualified technician.
 Never repair the unit while it is plugged in.
 Immediately unplug the unit if it makes strange
sounds, emits smells or smoke comes out of it,
and contact customer service.
 Do not remove any part of the casing unless
instructed by an authorized technician.
 You should never attempt to repair the unit
yourself.
 Contact EdgeStar Support if the unit needs repair
service.
i
General Safety
 To prevent back and other types of injuries, use at
least two people to move and install the wine cooler.
 This appliance is not intended for use by persons,
including children, with reduced physical, sensory or
mental capabilities, unless they have been given
supervision or instruction concerning the use of the
appliance by the person(s) responsible for their
safety.
 Install the wine refrigerator in a well ventilated area
where the ambient temperature is above 50°F and
below 95°F.
 The temperature range for this cooler is optimized
for wine and beverage storage. Perishable food
items may require a different storage environment.
 Do not place hot or warm items into the cooler
before they cool down to room temperature.
 This unit is designed to be installed indoors, and
protected from rain, sleet, snow, and/or moisture.
 This unit is not intended to be used by children.
 Children should be supervised to ensure that they
do not play with this product.
 Never allow children to crawl inside the wine
refrigerator. If disposing the unit, remove the door.
 Do not use this appliance near flammable gas or
combustibles, such as gasoline, benzene, thinner,
etc.
 Do not place the unit near heat sources such as
ovens, grills, or direct sunlight.
 Only use in an upright position on a flat, level
surface and provide proper ventilation.
 Do not pinch or kink the power supply line between
the unit and cabinet.
 Do not leave any cleaning solutions in the unit
 Do not use solvent-based cleaning agents or
abrasive solutions to clean the unit as they may
damage the interior and exterior.
 Do not place any other appliances on top of the unit.
 Do not turn the unit upside down, on its side, or at
an angle off level.
 If your model wine cooler is equipped with a lock,
take care to keep the keys away from children.
 Do not move the unit without emptying the contents
and securing the door in a closed position.
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................. I INTRODUCTION ................................................................................................... 1 PARTS IDENTIFICATION ..................................................................................... 2 BACK VIEW .......................................................................................................... 2 FRONT VIEW ........................................................................................................ 2 INSTALLING THE WINE REFRIGERATOR ......................................................... 3 TYPES OF INSTALLATION....................................................................................... 3 Free-standing installation: ............................................................................. 3 Built-in installation: ........................................................................................ 3 INSTALLATION CLEARANCE REQUIREMENTS .......................................................... 4 ELECTRICAL REQUIREMENTS ................................................................................ 5 Recommended grounding method ................................................................ 5 LEVELING THE WINE REFRIGERATOR .................................................................... 5 INSTALLING THE DOOR HANDLE ............................................................................ 6 INSTALLING AND REMOVING THE SHELVES ............................................................ 6 REVERSING THE DOOR SWING.............................................................................. 7 OPERATION .......................................................................................................... 8 INSTALLATION CHECK LIST BEFORE OPERATION .................................................... 8 USING THE TEMPERATURE CONTROL PANEL ......................................................... 8 NORMAL SOUNDS ................................................................................................ 9 DEFROSTING ....................................................................................................... 9 PREPARING THE WINE REFRIGERATOR FOR STORAGE ........................................... 9 CLEANING AND MAINTENANCE ...................................................................... 10 EXTERIOR CLEANING ......................................................................................... 10 INTERIOR CLEANING ........................................................................................... 10 TROUBLESHOOTING ........................................................................................ 10 TROUBLESHOOTING CONTINUED ......................................................................... 11 SPECIFICATIONS ............................................................................................... 12 EDGESTAR LIMITED WARRANTY ........ ERROR! BOOKMARK NOT DEFINED. First Time Operating Instructions
Before use, make sure all packaging labels and materials are all removed from
the unit. Be sure to keep track of all included parts and pieces before discarding
packaging materials. It is advised that you keep the original box and packaging
materials in case you are ever to move or ship the appliance in the future.
Let the unit stand for at least 24 hours before you use it; this allows the cooling
components time to settle from transit. The instruction manual should be read
before use.
This owner’s manual is provided for reference use only. Specifications may
change without prior notice. Refer to the product label on the back of your
wine refrigerator for the latest technical information.
EdgeStar Wine Refrigerator
ii
Introduction
Thank you for purchasing this EdgeStar wine refrigerator. We are glad you chose
us. We believe that your purchase of this product opens a relationship between
you and EdgeStar. We will provide the customer support needed to nurture that
relationship.
This manual contains important information regarding the proper installation, use
and maintenance of your wine refrigerator. Following this manual will ensure that
your product will work at its peak performance and efficiency.
Please save the original product packaging in case you need to safely transport
your wine refrigerator.
For Your Records:
Please write down the model number and serial number
below for future reference. Both numbers are located on the
ratings label on the back of your unit and are needed to
obtain warranty service. You may also want to staple your
receipt to this manual as it is the proof of your purchase, and
is also needed for service under your warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer service:
1

If you received a damaged product, immediately contact the retailer or
dealer that sold you the product.

Read and follow this instruction manual carefully to help you install, use
and maintain your wine refrigerator.

Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.

Visit us on the web at http://www.edgestar.com to register your
product, download product guides, additional troubleshooting resources
and up-to-date information.

If you need warranty service, our friendly customer service
representatives are available via email at service@edgestar.com or by
telephone at 1 (866) 319-5473.
Parts Identification
Top Right Hinge
Front View
Control Panel
Carbon Filter
Internal Fan
Shelf
Door Handle
Stainless Steel Door
Note: The carbon filter
should be replaced
every 3-6 months
depending on the
unit’s exposure level
to odor. If the unit is
placed in the kitchen
regular replacement
every 3 months is
ideal.
Front vent
Leveling foot
Back View
Product Label
Tip: Gather the model
and serial number
from the product label
and write them down
before installing the
wine refrigerator.
Power Cord
Cabinet
EdgeStar Wine Refrigerator
Power Plug
2
Installing the Wine refrigerator
The wine refrigerator should be installed in accordance with local
electrical code requirements. The wine refrigerator should also be placed
in a location that is strong enough to support its total weight, keeping in
mind that it will weigh substantially more when fully loaded than when
empty.
Before you plug the wine refrigerator into a power supply, be sure to let it
stand upright for at least 24 hours to allow the compressor’s oils to settle.
Unpacking the Wine refrigerator
WARNING: Use two more people to move and install the wine
refrigerator. Failure to do so can result in back or other injury. Carefully
remove the packaging materials. Remove any shipping tape and glue
from your wine refrigerator before using. Do not use sharp instruments,
rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or
glue. These products can damage the surface of your wine refrigerator.
IMPORTANT: Do not remove any safety, warning, or product information
labels from your wine refrigerator.
Types of Installation
This wine refrigerator has been designed for free-standing, or built-in
installation. In every case, there must be adequate ventilation and access
for service.
Free-standing installation:
A free-standing installation will allow you to install the wine refrigerator in
almost any place you desire. You must follow the stated instructions for
electrical requirements, and leveling the wine refrigerator.
Built-in installation:
A recessed installation will allow you to install the beverage cooler under
a counter or in a kitchen cabinet provided the required clearance space
around the beverage cooler is followed.
It is necessary to allow adequate ventilation space around the unit (make
sure there is at least some ventilation room for the back of the unit). The
following additional items must be observed.
1. Place the wine refrigerator in front of the installation location. Adjust
the feet and place the unit flat on the floor or on a platform depending
on your installation requirements.
2. If the electrical outlet for the wine refrigerator is behind the cabinet,
plug in the wine refrigerator.
3. Push the wine refrigerator into position.
WARNING: Do NOT install the wine refrigerator behind a closed cabinet
door.
3
Installation Clearance Requirements
When installing the wine refrigerator under a counter, follow the
recommended spacing dimensions shown.
• To ensure proper service access and ventilation, allow at least 2/5”
clearance at the back, 1/5” at top and 1/5” at sides. The installation
should allow the unit to be pulled forward for servicing, if necessary.
Important Notes:
Top View
• Choose a location that has
ambient temperatures above
50°F and below 95°F.
Operation outside these
temperatures may result in
lowered efficiency or cause
other adverse effects.
Back of unit
• This unit MUST be installed
in an area protected from the
elements, e.g., wind, rain,
water spray or drips.
• The wine refrigerator should
not be located next to ovens,
grills or other high heat
sources.
Door Hinge
Side View
• Do not kink or pinch the
power supply cord between
the wine refrigerator and wall
or cabinet.
• The wine refrigerator should be installed on a firm and level surface that
will be able to support the entire weight of a fully loaded unit. It is
important for the wine refrigerator to be level in order to work properly. If
needed, you can adjust the height of the wine refrigerator by rotating the
feet. See the “Leveling the Wine refrigerator” section.
• A standard electrical supply (115 VAC only, 60 Hz), properly grounded
in accordance with National Electrical Code and local codes and
ordinances is required.
EdgeStar Wine Refrigerator
4
Electrical Requirements





ELECTRIC SHOCK HAZARD!
Plug into a grounded 3-prong outlet.
Never remove the grounding prong from the plug.
Never use an adapter to bypass the grounding prong.
DO NOT use an extension cord.
Failure to follow these instructions can result in fire,
electrical shock, or death.
Before you move your wine refrigerator into its final location, it is
important to make sure you have the proper electrical connection:
A standard electrical supply (115 V, 60Hz), properly grounded in
accordance with the National Electrical Code and local codes and
ordinances, is required.
It is recommended that a separate circuit, serving only your wine
refrigerator, be provided. Use receptacles that cannot be turned off by a
switch or pull chain.
The fuse (or circuit breaker) size should be 3 Amps.
Recommended grounding method
For your personal safety, this appliance must be grounded. It is equipped
with a power supply cord having a 3-prong grounding plug. To minimize
possible shock hazard, the cord must be plugged into a mating 3-pronged
wall socket, and grounded in accordance with the National Electrical
Code and local codes and ordinances. If a mating wall socket is not
available, it is the personal responsibility of the customer to have a
properly grounded, 3-prong wall receptacle installed by a qualified
electrician.
Leveling the Wine Refrigerator
It is important for the wine refrigerator to be leveled in order to work
properly. It can be raised or lowered by rotating the plastic sheaths
around each of the feet on the bottom of the machine. If you find that the
surface is not level, rotate the feet until the wine refrigerator becomes
level .You may need to make several adjustments to level it. We
recommend using a carpenter’s level to check the machine.
1. Place a carpenter’s level on top of the product to see if the wine
refrigerator is level from front to back and side to side.
2. Adjust the height of the feet as follows:
Turn the leveling feet to the right to lower that side of the refrigerator.
Turn the leveling feet to the left to raise that side of the refrigerator.
IMPORTANT: Once you are ready to install it in a cabinet or directly on
the floor, you must adjust the feet to level the wine refrigerator.
5
Installing the Door Handle
To install the door handle:
1. Open the door and carefully pull the door gasket around the area
where the handle is to be installed.
2. Carefully remove the two pre-installed decorative screws from the front
of the door. Note: some wine coolers do not have decorative plugs
installed.
3. Insert each Phillips head screw through the gasket side of the door
until the screw pass through the door.
4. Align the handle with the screws and tighten using a Phillips head
screwdriver until the handle is flush against the door frame.
CAUTION: Do not over-tighten the screws as this may cause damage to
the handle or to the stainless steel door
5. Carefully press the door gasket into its original position.
Installing and Removing the Shelves
To prevent damaging the door gasket, make sure to open the door all the
way before pulling the shelves out of their track.
To install the shelves:
1. Open the door completely.
2. Slide the shelf on the shelf track and slowly push back until it stops.
3. Push down on the front of the shelf to allow the back of the shelf to lift
over the plastic post. (Imagine a seesaw movement.) Continue to push
the shelf back until both notches pass through the plastic posts on each
side of the shelf track.
4. Continue to push the shelf back.
To remove the shelves:
1. Open the door completely.
2. If necessary, make sure you remove all the contents sitting on the
shelf.
3. Pull the shelf forward until the notch aligns with the plastic post on each
side of the shelf track.
4. Lift the shelf until both notches pass through the posts.
5. Continue to pull the shelf forward until it is completely removed from
the inner compartment.
EdgeStar Wine Refrigerator
6
Reversing the Door Swing
Follow the instructions below to reverse the door swing.
IMPORTANT: Before you begin, unplug the refrigerator.
To reverse the door from right swing to left swing:
1. Open the door and using a Phillips screwdriver, remove the two
bottom screws from the lower hinge. Be careful to hold the glass
door with hands from dropping after removing the screws.
2. Carefully slide the bottom of the door forward and down, and
place it on a padded surface to prevent damaging it.
3. Remove the right upper hinge. Install the left upper hinge
included in the plastic bag that includes the instruction manual.
4. Remove the right lower hinge. Install the left lower hinge
included in the plastic bag.
5. Align the glass door to the designated position making sure that
the door shaft enters the door hole at the left upper corner of the
glass door. Install the lower hinge supporter at the left lower corner
of the glass door.
6. Install the two screws that are used to connect the left lower
hinge with the glass door and tighten them before the door is
leveled.
7
OPERATION
Installation Check List before Operation
1. Have all packing materials and tape been removed from the interior and
exterior of the wine refrigerator?
2. Have the installation instructions been followed, including connecting the
machine to electricity? And has proper grounding been installed for the wine
refrigerator?
3. Has the machine been leveled?
4. Is the wine refrigerator in a site where the ambient temperature is between 50º
F and 95º F all year round?
5. Is there a clearance of at least 2/5” at the rear, 1/5” at the top and 1/5” at the
sides for proper air circulation?
Using the Temperature Control Panel
Use the up and down buttons to adjust the temperature. The temperature
displayed can be in Fahrenheit or Celsius. This wine cooler has a
temperature range from 40°F to 65°F.
Note: Whether your wine
cooler can reach the actual
set temperature depends on
the ambient environmental
conditions.
This wine cooler has one display. The default display will show the
current temperature inside the unit. If the temperature is adjusted with
the up and down buttons the display will show the set temperature. Once
the set temperature is placed the display will revert back to the current
temperature display.
Press the
button on the control panel to lower the temperature by 1
degree increments.
Allow at least 24 hours before storing your wines and to allow the
temperature to acclimate.
Press the
button on the control panel to increase the temperature by 1
degree increments.
Press the
Caution: If you powered off
the unit, please wait at least
5 minutes before powering it
back on.
EdgeStar Wine Refrigerator
button to turn the inner light on or off.
Press and hold the power button for approximately 3 seconds to turn the
unit’s power on or off. The Run Light will illuminate when the unit is
working.
The Celsius or Fahrenheit light will be lit depending on what scale
temperature is being displayed. To switch between C and F, press and
hold the
and
buttons at the same time for approximately 5 seconds
until the temperature scale changes.
8
Normal Sounds
Your new wine refrigerator may make sounds that are not familiar to
you. Most of the new sounds are normal. Hard surfaces like the
floor, walls can make the sounds seem louder than they actually
are. The following describes the kinds of sounds that might be new
to you and what may be making them.
 Rattling noises may come from the flow of the refrigerant or the
water line, Items stored on top of the wine refrigerator can also
make noises.
 The high efficiency compressor may make a pulsating or highpitched sound.
 Water running from the evaporator to the water bin may make a
splashing sound.
 As each cycle ends, you may hear a gurgling sound due to the
refrigerant flowing in your wine refrigerator.
 You may hear air being forced over the condenser by the
condenser fan.
Defrosting
Note that under most refrigerating settings, the unit will
automatically defrost under most ambient conditions. However, on
colder settings, some frost may build up. Additionally, the more
humid the ambient conditions, the more frost may build up. Keep
the door closed as much as possible and avoid opening the door
unnecessarily to minimize frost build-up.
If frost is preventing the door from closing properly, you may need
to power the unit off until the frost melts. Use a soft absorbent towel
to dry the unit.
WARNING: Never attempt to remove frost with a sharp object!
Preparing the Wine Refrigerator for Storage
If the wine refrigerator will not be used for a long time, or is to be
moved to another place, it will be necessary to defrost the unit and
dry the interior.
IMPORTANT:
1. Disconnect the cooler from the power supply by removing the
power plug from the wall socket.
2. Leave the door open to allow for air circulation and to prevent
mold, mildew and unpleasant smells.
• Do not touch the power plug
when your hands are wet.
• Never unplug the unit by
pulling on the plug.
CAUTION: Store the unit out of the reach of children. If you have
children, you may want to take additional precautions such as
removing the door to prevent a child from being trapped inside the
cooler!
9
CLEANING AND MAINTENANCE
Periodic cleaning and proper maintenance will ensure efficiency, top
performance, and long life.
Exterior Cleaning
The door and cabinet may be cleaned with a mild detergent and
lukewarm water solution such as 2 tablespoons of baking soda to 1 quart
of water.
Do not use solvent based or abrasive cleaners. Use a soft sponge and
rinse with clean water. Wipe with a soft clean towel to prevent water
spotting. If the door panel is stainless steel, it can discolor when exposed
to chlorine gas and moisture. Clean stainless steel with a cloth dampened
with a mild detergent and warm water solution. Never use an abrasive or
caustic cleaning agent.
Interior Cleaning
The wine refrigerator’s interior should be cleaned occasionally.
1. Disconnect power to the unit.
2. Open the door and remove the contents and shelves.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reinsert the shelves and beverages.
6. Reconnect power to the unit.
TROUBLESHOOTING
Before Calling for Help
If the unit appears to be malfunctioning, read through the OPERATION
section of this manual first. If the problem persists, check the
Troubleshooting Guide below and on the following page. The problem
could be something that can easily be solved or explained.
Symptoms
The wine cooler turns
on and off frequently.
Possible causes
Solutions
The room temperature is
higher than the
recommended ambient
environment.
Run the cooler at the appropriate ambient temperature.
The door is being opened
often.
Minimize the number of times the door is opened.
The door is not completely
closed.
Make sure the door is completely closed.
The door gasket is not
sealing properly.
Make sure the door gasket is properly sealing.
The cooler does not have the
suggested ventilation.
Read and follow the “Installation Clearance
Requirements” section.
EdgeStar Wine Refrigerator
10
Troubleshooting continued
Issue
The wine cooler does not
turn on.
The wine cooler will not
reach the desired
temperature
Possible cause
Solution
There is a power failure.
Ensure the cooler is plugged in and the power outlet has
power.
The cooler is not plugged in.
Plug the unit in to a power outlet that has sufficient
amperage.
A house fuse has blown or
the circuit breaker is tripped.
Replace the broken fuse in your fuse box or reset the
breaker.
The cooler is placed too
close to a heat source.
Keep the cooler away from direct sun light or other heat
sources.
The cooler does not have
sufficient ventilation.
Read and follow the “Installation Clearance Requirements”
section.
The door is opened too
frequently or for a long
period of time.
Close the door tightly and do not open the door too
frequently or for a long period of time.
Certain sounds are normal.
Read the “Normal Sounds” section.
The unit is not level or is
touching another appliance.
Check to make sure that the cooler is level, and that it is
not in contact with another appliance or furniture.
The unit is not grounded
properly.
Contact your local electrician to test your electrical
grounding system.
The environment is humid.
Though the unit uses an “auto-defrost” system, under
certain conditions, manual defrosting may be required. If
frost builds up, you can try running the cooler on a warmer
temperature setting, minimizing the number of times you
open the door, or unplugging the unit to allow the frost to
melt.
The wine cooler is making
strange noises
The body of the wine
refrigerator is electrified.
Frost is forming in the
wine cooler.
The ambient temperature is
too low.
The door is being opened
too frequently.
Your cooler is not level.
The door gasket is dirty.
The door will not shut
properly.
11
Make sure the cooler is on a level surface.
Clean the door gasket.
The door gasket is not
installed correctly.
Make sure the door gasket is properly installed.
The shelves are incorrectly
installed.
Correctly install the shelves.
Specifications
Description of product
Built-in Wine Refrigerator
Model
CWR181SZ
Voltage/Frequency
AC 115V~60Hz
Amperage
1.25A
Input Power
100W
Color
Black Cabinet; Stainless Steel
Door
Storage Capacity
18 Bottles*
Refrigerant
R134a, 1.77 oz.
Temperature Range
40 - 65ºF
Dimensions
(Height x Width x Depth )
34 1/4” x 11 5/8” x 22 5/8”
Weight
66 pounds
Note: Technical data and performance information is provided for
reference only.
Specifications are subject to change. Check the rating label on the wine
refrigerator for the most accurate information.
*Note on wine storage capacity:
The wine refrigerator will store 18 standard 750 ml. wine bottles. You will
need to arrange the wine bottles in a reverse racked position to be able to
store 18 bottles.
EdgeStar Wine Refrigerator
12
Limited Warranty: Full One-Year Parts and Labor
This product is warranted by EdgeStar and is subject to any conditions set forth as follows:
WHAT IS COVERED:
For a period of ONE (1) YEAR from the date of
original retail purchase, EdgeStar will repair or
replace any part free of charge including labor
that fails due to a defect in materials or
workmanship. Labor will be performed free of
charge at an authorized EdgeStar repair facility
and EdgeStar will supply new, rebuilt, or
refurbished parts free of charge. EdgeStar may
request a defective part be returned in
exchange for the replacement part. All
replacement parts or products will be new,
remanufactured, or refurbished. All products and
parts replaced by EdgeStar under warranty
service become the property of EdgeStar. After
the 12 month period, EdgeStar will no longer be
responsible for labor charges incurred or
replacement parts. All defective products and
parts covered by this warranty will be repaired or
replaced on a mail-in basis to an EdgeStar
authorized repair facility.
This warranty applies to the original purchaser
only, and only covers defects in workmanship
experienced during operation of the product
under normal service, maintenance, and usage
conditions. This warranty applies to the purchase
and use of this product in residential settings
within the United
States of America.
Exceptions: Commercial or Rental Use
Warranty
90 days labor and parts from date of original
purchase. No other warranty applies.
WHAT IS NOT COVERED- The following limitations apply to the
coverage of this warranty. This warranty does not cover:
-Labor charges for installation, setup or training to use the
product.
-Shipping damage, and any damage caused by improper
packaging for shipment to an authorized service center, and any
damaged caused by improper voltage or any other misuse,
including abnormal service, handling, or usage.
-Cosmetic damage such as scratches and dents.
-Normal wear and tear on parts or replacement of parts designed
to be replaced, e.g. filters, cartridges, batteries.
-Service trips to deliver, pick-up, or repair, install the product, or to
instruct in proper usage of the product.
-Damages or operating problems resulting from misuse, abuse,
operation outside environmental specifications, uses contrary to
instructions provided in the owner’s manual, accidents, acts of
God, vermin, fire, flood, improper installation, unauthorized
service, maintenance negligence, unauthorized installation or
modification, or commercial use.
-Labor, service transportation, and shipping charges for the
removal and replacement of defective parts, beyond the initial 12
month period.
-Products that have been modified to perform outside of
specifications without the prior written permission of EdgeStar.
-Products lost in shipment, or theft.
-Products sold AS IS or from an unauthorized reseller.
-Products that have had their serial numbers removed, defaced,
or with serial numbers that have been invalidated.
-Damage from other than normal household use.
-Replacement or repair of household fuses, circuit breakers, wiring
or plumbing.
-Damage to personal property from use of product.
-Damage from service other than from an authorized EdgeStar
repair facility.
-Hoses, knobs, lint trays and all attachments, accessories and
disposable parts.
-Any service charges not specifically identified as normal such as
normal service area or hours.
-Any special or consequential damages arising out of the use of
the product.
OBTAINING WARRANTY SERVICE: If you believe your product is defective, contact EdgeStar Customer Support for
troubleshooting assistance and warranty service at www.edgestar.com or call 1-866-319-5473. Before contacting
Customer Support you are required to have your model number, serial number and proof of purchase available upon
request. Once an EdgeStar authorized representative has confirmed that your product is defective and eligible for
warranty service, the product must be returned to an EdgeStar authorized repair facility. EdgeStar is not responsible for
damage resulting from shipper mishandling or improper packaging. Do not return a defective product to the place of
purchase. Products received without a return authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
EdgeStar Products
500 N. Capital of TX Hwy, Bldg 5
Austin, TX 78746
Toll Free: 1-866-319-5473
Web: http://www.edgestar.com
E-mail: service@edgestar.com
Register your product, download owner’s manuals, access additional
troubleshooting resources, and obtain more information on other
great EdgeStar products on the web at: http://www.edgestar.com
Product contents and specifications may change without notice.
Copyright © 2011 Living Direct, Inc. All rights reserved.
Download PDF