CMA Dishmachines | AHC | Specifications | CMA Dishmachines AHC Specifications

www.hatcocorp.com
Register Online!
(see page 2)
Electric Booster Water Heaters
Imperial ‘S’, Compact ‘C’,
Mini-Compact ‘MC’ Series
Installation and Operating Manual
P/N 07.04.111.00
WARNING
Do not operate this equipment unless you
have read and understood the contents of
this manual! Failure to follow the
instructions contained in this manual may
result in serious injury or death. This
manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
ADVERTENCIA
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en este
manual puede resultar en un serio lesión
o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted no
puede entender el contenido de este
manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
AVERTISSEMENT
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel !
Le
non-respect
des
instructions
contenues dans ce manuel peut entraîner
de graves blessures ou la mort. Ce
manuel contient des informations
importantes
concernant
l'entretien,
l'utilisation et le fonctionnement de ce
produit. Si vous ne comprenez pas le
contenu de ce manuel, veuillez le signaler
à votre supérieur. Conservez ce manuel
dans un endroit sûr pour pouvoir vous y
référer plus tard.
© 2012 Hatco Corporation
CONTENTS
Important Owner Information ..............................................2
Introduction ...........................................................................2
Important Safety Information...............................................3
Model Description.................................................................5
all models ........................................................................5
Imperial models “S” Series ..............................................5
Compact models “C” Series.............................................5
mini-Compact models “mC” Series..................................5
Specifications........................................................................6
Circuit Breaker and Fused Disconnect Switch Sizes.......6
Sizing Chart for Low-Temp Dish machines......................9
Booster Heater Sizing Chart ..........................................10
Capacity Charts .............................................................14
Dimensions ....................................................................15
Installation ...........................................................................17
General ..........................................................................17
Plumbing Installation......................................................18
Electrical-all Sizes and Voltages ...................................23
Operation .............................................................................24
General ..........................................................................24
Maintenance ........................................................................25
General ..........................................................................25
Thermostat adjustment..................................................25
High Temperature Limit Safety Switch...........................25
Options and Accessories...................................................26
Troubleshooting Guide ......................................................27
Hatco Limited Warranty......................................................30
Authorized Parts Distributors ............................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and
purchase date of the unit in the spaces below (specification
label located on the unit). Please have this information available
when calling Hatco for service assistance.
Business
Hours:
model No. ________________________________________
Serial No. ________________________________________
8:00 am to 5:00 Pm
Central Standard Time (C.S.T.)
(Summer Hours: June to September –
8:00 am to 5:00 Pm C.S.T.
monday through Thursday
8:00 am to 2:30 Pm C.S.T. Friday)
Telephone: (800) 558-0607; (414) 671-6350
Voltage __________________________________________
E-mail:
Date of Purchase __________________________________
Fax:
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. access the Hatco website at
www.hatcocorp.com, select the Parts & Service pull-down
menu, and click on “Warranty Registration”.
partsandservice@hatcocorp.com
(800) 690-2966 (Parts and Service)
(414) 671-3976 (International)
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling (800) 558-0607.
additional information can be found by visiting our web site at
www.hatcocorp.com.
INTRODUCTION
This manual provides the installation, safety, and operating
instructions for the Hatco Electric Booster Water Heaters. Hatco
recommends all installation, operating, and safety instructions
appearing in this manual be read prior to installation or
operation of the unit.
Hatco Electric Booster Water Heaters are designed
for use with commercial dish machines to boost the temperature
of the regularly available hot water, usually 110°–150°F
(43°–66°C) up to 180°F (82°C). Water at 180°F (82°C) can be
used as sanitizing rinse water in commercial dish machines in
accordance with Health Codes, NSF Standard #5 and plumbing
codes.
Safety information that appears in this manual is identified by
the following signal word panels:
all Hatco Booster Heaters are ready for electrical and plumbing
service connections, with an adjustable ambient compensated
immersion thermostat(s) and a high temperature limit switch.
The service area is accessible from the front of the unit,
permitting easy access.
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
Hatco Electric Booster Water Heaters are products of extensive
research and field testing. The materials used were selected for
maximum durability, attractive appearance, and optimum
performance. Every unit is inspected and tested thoroughly prior
to shipment.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
2
NOTICE is used to address practices not related to
personal injury.
Form No. EBOOSTERm-0712
IMPORTANT SAFETy INFORMATION
Read the following important safety information before using this equipment to avoid
serious injury or death and to avoid damage to equipment or property.
WARNING
WARNING
ELECTRIC SHOCK HAzARD:
• Unit must be installed by qualified, trained installers.
Installation must conform to all local electrical and
plumbing codes. Installation by unqualified personnel
will void the unit warranty and may lead to electric
shock or burn, as well as damage to unit and/or its
surroundings. Check with local plumbing and electrical
inspectors for proper procedures and codes.
FOR INSTALLING PRESSURE AND TEMPERATURE
RELIEF vALvES IN ACCORDANCE WITH AMERICAN
NATIONAL STD. z21.22-1979. Combination pressure and
temperature relief valves with extension thermostats must
be installed so that the temperature-sensing element is
immersed in the water within the top 6" (152 mm) of the
tank. They must be installed directly in a tank tapping.
Combination pressure and temperature relief valves that
do not have extension elements must be mounted directly
in a tank tapping located within the top 6" (152 mm) of the
tank, and shall be adequately insulated and located so as
to assure isolation from ambient conditions that are not
indicative of stored water temperature. TO AvOID WATER
DAMAGE OR SCALDING DUE TO vALvE OPERATION,
DRAIN PIPE MUST BE CONNECTED TO vALvE OUTLET
AND RUN TO A SAFE PLACE OF DISPOSAL. Discharge
line must be as short as possible and be the same size as
the valve discharge connection throughout its entire
length. Drain line must pitch downward from the valve and
must terminate between 1-1/2" (38 mm) and 6" (152 mm)
above the floor drain where any discharge will be clearly
visible. The drain line shall terminate plain, not threaded,
with material serviceable for temperatures up to 250°F
(121°C) or greater. Excessive length, over 30' (9.1 m), or
use of more than four elbows can cause a restriction and
reduce the discharge capacity of the valve. No shut-off
valve shall be installed between the relief valve and tank,
or in the drain line. valve lever must be tripped
periodically to assure that waterways are clear. This
device is designated for emergency safety relief and shall
not be used as an operating control. The valves are set to
relieve at 150 psi (1034 kPa) or when water temperature
reaches 210°F (99°C). Read tag on valve for additional
information.
• Turn OFF power at fused disconnect switch/circuit
breaker and allow unit to cool before performing any
cleaning, adjustments, or maintenance.
• Consult a licensed electrical contractor for proper
electrical installation conforming to local electrical
codes and the National Electrical Code (N.E.C.).
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• Do not place aftermarket covers on or over booster
heater. Doing so can cause temperature and moisture
build-up resulting in premature failure and electrical
shock.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
Use only plumbing material suitable for a minimum water
temperature of 200°F (93°C). Materials used must meet
National Sanitation Foundation (NSF) specifications and
all local plumbing codes and regulations.
valves supplied by Hatco are designed for hightemperature commercial operation. Do not substitute Hatco
valves with valves designed for domestic water heaters.
Units are equipped with a high temperature limit safety
switch that will shut off the power if the unit overheats.
Contact an Authorized Hatco Service Agent if the high
temperature limit safety switch cannot be reset or
continues to trip.
Temperature/pressure protective equipment should not
be less than a combination temperature/pressure relief
valve certified by a nationally recognized testing
laboratory that maintains periodic inspection of the
production of this equipment and meets the requirements
for Relief valves and Automatic Shutoff Devices for Hot
Water Supply Systems, ANSI z21.22-1979. The
temperature/pressure relief valve must be marked with a
minimum set pressure not to exceed the marked
hydrostatic test pressure of the booster heater as noted
on the unit specifications.
Install booster water heater in a horizontal position with
the base parallel to the floor and the inlet connection at
the lowest point. Improper installation could create an
unsafe condition.
Do not connect booster water heaters to domestic
(consumer) dish machines or other domestic utilized
equipment. This booster may damage domestic equipment.
ExPLOSION HAzARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
Form No. EBOOSTERm-0712
3
IMPORTANT SAFETy INFORMATION
Read the following important safety information before using this equipment to avoid
serious injury or death and to avoid damage to equipment or property.
WARNING
CAUTION
This product contains fiberglass, a product known to the
state of California to cause cancer, birth defects, or other
reproductive harm.
Hatco requires that two temperature/pressure gauges
(Hatco P/N 03.01.003.00) be installed to ensure proper
operation. Install one in the supply line before the
pressure reducing valve and one in the outlet line as close
to the booster heater as possible. This provides a visual
check of the water temperature and pressure before and
after the water heater.
Install booster water heater as close as possible to a
commercial dish machine. Employ re-circulation if
distance between water heater and dish machine exceeds
National Sanitation Foundation (NSF) specifications of
five (5) linear feet (1524 mm).
If water supply pressure to the booster inlet is over 20 psi
(138 kPa) during flow, install pressure reducing valve with
built-in bypass (Hatco P/N 03.02.004.00) for proper
operation of dish machine rinse nozzles.
Follow standard welding safety and operational procedures
when attaching sliderails to bottom of dishtable.
Make sure the dishtable is strong enough to support the
weight of the heater AND water when installing with slide
mounting brackets.
NOTE: The pressure reducing valve must be the type
equipped with a high pressure bypass, as supplied by
Hatco.
Refer to the BOOSTER HEATER SIzING CHART in this
manual to ensure proper sizing and avoid personal injury
and/or damage to the booster heater.
DO NOT turn on power to the booster heater until tank has
been filled with water and all air has been vented through
the dish machine rinse nozzles. Heating elements will
burn out in seconds if operated when not immersed in
water.
It is essential to recognize that even though a water heater
may be properly installed initially and approved, there
always exists the possibility that unknowing individuals
might alter or change the installation in a manner that
would render it unsafe. Therefore, it is important that all
safety programs provide some mechanism to assure that
these installations are inspected periodically.
NOTICE
Always drain booster heater with power to the unit off or
element burnout could occur.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.
Use dielectric couplings when connecting dissimilar
metals, such as galvanized to copper. This will prevent
electrolysis or premature plumbing damage.
Do not turn or adjust outlet water connection on all Large
Compact Series units (C-24 to C-57).
Do not turn or adjust inlet water connection on Compact
Series Booster Heaters or internal water flow will change.
CAUTION
BURN HAzARD:
• Water in unit is very hot. Wear protective gloves and
proper attire when operating to avoid injury.
Do not back out or loosen any pipe fittings or leaks may
occur.
• valves supplied by Hatco are designed for high
temperature commercial operation. Do not substitute
Hatco valves with valves designed for domestic water
heaters.
Do not lay unit on the side with the control panel. Damage
to the unit could occur.
Incoming water in excess of 3 grains of hardness per
gallon (GPG) (0.75 grains of hardness per liter [GPL]) must
be treated and softened before being supplied to booster
heater(s). Water containing over 3 GPG (0.75 GPL) will
decrease efficiency, increase energy use, and reduce the
operating life of the unit through increased lime build-up.
Product failure caused by liming or sediment buildup is
not covered under warranty.
Do not use anti-siphon valves on incoming water line.
Check valves on incoming water line is not recommended.
Damages caused by the use of check valves on unit will
not be covered by warranty.
Do not connect booster heater directly to a boiler or
furnace coil or any other uncontrolled temperature
source. The booster heater thermostat could be damaged
causing unit to overheat.
Do not use deionized water. Deionized water will shorten
the life of water reservoir and heating element.
Units are voltage-specific. Refer to specification label for
electrical requirements before beginning installation.
Connecting unit to incorrect power supply will void
product warranty and may damage unit.
Do not connect an expansion tank of any type to booster
heater water lines.
4
Form No. EBOOSTERm-0712
MODEL DESCRIPTION
Mini-Compact Models “MC” Series
All Models
Hatco mini-Compact models feature a stainless steel tank and
6" (152 mm) legs. mini-Compact units have a capacity of 3.2
gallons (12 liters) and provide up to 172 gph (651 lph) of
sanitizing rinse water based on a 40°F (22°C) temperature rise.
Ideal for either hot water sanitizing or point-of-use hot water
dispensing.
Hatco Electric Water Booster Heaters are available in three
models: Imperial, Compact, and mini-Compact. all standard
models include a booster heater with low-water cut-off system,
temperature/pressure relief valve, pressure reducing valve with
built-in high pressure bypass, two temperature/pressure gauges
and a high temperature limit safety switch.
Imperial Models “S” Series
NOTE: Mini-Compact models can be configured with an
optional Power ON/OFF (I/O) switch.
Hatco Imperial models feature a Castone tank with a 10 year
limited warranty, a Power ON/OFF (I/O) switch, an indicator light
and 6" (152 mm) legs. Imperial units have a capacity of 16
gallons (61 liters) and provide up to 573 gallons per hour (gph)
(2169 liters per hour [lph]) of sanitizing rinse water based on a
40°F (22°C) temperature rise.
®
mini-Compact model
Imperial model
Compact Models “C” Series
Hatco Compact models feature a Castone® tank with a 10 year
limited warranty, a Power ON/OFF (I/O) switch, an indicator light
and either 6" (152 mm) legs or slide mounting brackets for
mounting under a dish table. Compact units have a capacity of
6 gallons (23 liters) and provide up to 573 gph (2169 lph) of
sanitizing rinse water based on a 40°F (22°C) temperature rise.
Compact model
Form No. EBOOSTERm-0712
5
SPECIFICATIONS
Circuit Breaker and Fused Disconnect Switch Sizes — 4 to 12 kW
kW
4
5
voltage Phase
208
240
480
208
240
480
6
7
9.9
10.4
10.5
11.4
12
1
1
1
208
208
240
240
380
480
600
1
3
1
3
3
3
3
208
208
240
240
380
480
600
1
3
1
3
3
3
3
208
3
208
208
240
240
380
480
600
9
1
1
1
208
208
1
3
1
3
3
3
3
1
3
L1
19
17
8
24
21
10
29
14
25
13
9.2
6
5.7
34
17
29
15
11.4
7
6.7
43
22
38
19
13.3
9
8.7
47.5
27.5
28.8
Amp Draw
L2
L3
Breaker or Fuse
Size
Copper Wire
Size
Conduit Size
24
21
10
----
30
30
15
10
10
14
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
19
17
8
29
25
25
22
9.2
11
5.7
34
29
29
25
11.4
13
6.7
43
38
38
33
13.3
16.3
8.7
47.5
27.5
28.8
----
8
8
8
10
14
14
14
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
-22
-19
13.3
9
8.7
60
50
50
50
20
30
15
6
8
8
8
12
12
14
1/2″
1/2″
1/2″
1/2″
1/2″
1/2″
1/2″
28.8
40
8
1/2″ (13 mm)
-17
-15
11.4
7
6.7
51
29
44
25.3
12.6
10
-29
-25.3
12.6
10
208
208
240
240
380
480
600
1
3
1
3
3
3
3
58
33
50
29
19.1
14.5
11.6
58
33
50
29
19.1
14.5
11.6
-33
-29
19.1
14.5
11.6
47.5
27.5
13.7
50
40
40
40
15
20
15
-27.5
51
29
44
25.3
12.6
10
47.5
27.5
13.7
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
40
40
40
30
15
15
15
1
3
1
3
3
3
1
3
3
10
10
14
-14
-13
9.2
6
5.7
208
208
240
240
480
600
240
240
480
30
30
15
60
40
-27.5
13.7
8
8
8
8
14
12
14
6
8
1/2″
3/4″
1/2″
1/2″
1/2″
1/2″
1/2″
(13
(19
(13
(13
(13
(13
(13
(13
(13
(13
(13
(13
(13
(13
mm)
mm)
mm)
mm)
mm)
mm)
mm)
mm)
mm)
mm)
mm)
mm)
mm)
mm)
1/2″ (13 mm)
1/2″ (13 mm)
70
40
60
40
20
15
4
8
6
8
12
14
3/4″
1/2″
1/2″
1/2″
1/2″
1/2″
90
50
70
40
30
20
15
3
8
4
8
10
12
14
1″ (25 mm)
1/2″ (13 mm)
3/4″ (19 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
60
40
20
6
8
12
(19
(13
(13
(13
(13
(13
mm)
mm)
mm)
mm)
mm)
mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
The shaded area contains electrical information for International models only.
NOTE: 250 kcmil maximum wire size for terminal block.
6
Form No. EBOOSTERm-0712
SPECIFICATIONS
Circuit Breaker and Fused Disconnect Switch Sizes — 13.5 to 30 kW
kW
13.5
15
17.25
18
24
27
30
volts
Phase
240
480
600
1
1
1
208
208
240
1
1
1
L1
65
38
56.3
33
16.3
13
Amp Draw
L2
L3
Breaker or Fuse
Size
Copper Wire
Size
Conduit Size
33
16.3
13
33
16.3
13
50
30
20
8
10
12
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
60
6
65
38
56.3
-38
--
90
50
90
208
208
240
240
380
480
600
1
3
1
3
3
3
3
72
41.7
62.5
36.1
23.0
18.1
14.5
72
41.7
62.5
36.1
23.0
18.1
14.5
-41.7
-36.1
23.0
18.1
14.5
90
60
90
50
30
30
20
208
240
240
380
480
600
1
1
3
3
3
3
86.5
75
43.4
27.3
21.7
17
86.5
75
43.4
27.3
21.7
17
--43.4
27.3
21.7
17
125
100
60
40
30
30
208
208
240
240
380
480
1
3
1
3
3
3
129.8
75
112.5
65
38.1
32.5
129.8
75
112.5
65
38.1
32.5
-75
-65
38.1
32.5
1
3
1
3
3
3
3
144
83.3
125
72.3
45.7
36
28.9
144
83.3
125
72.3
45.7
36
28.9
208
208
208
240
240
380
480
600
600
208
208
240
240
380
480
600
3
1
3
1
3
3
3
3
3
47.9
115.4
66.7
100
57.8
38.0
29.9
23
26
47.9
115.4
66.7
100
57.8
38.0
29.9
23
26
47.9
-66.7
-57.8
38.0
29.9
23
150
90
125
90
50
40
30
26
1″ (25 mm)
1/2″ (13 mm)
1″ (25 mm)
3
6
3
8
10
10
12
1″ (25 mm)
3/4″ (19 mm)
1″ (25 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1
3
6
8
10
10
1-1/4″ (32 mm)
1″ (25 mm)
3/4″ (19 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/0
3
1
3
8
8
10
175
100
150
90
50
50
2/0
3
1/0
3
8
8
200
125
175
100
60
50
40
3/0
1
2/0
3
6
8
8
40
-83.3
-72.3
45.7
36
28.9
3
8
3
8
3/4″ (19 mm)
1-1/4″ (32 mm)
1″ (25 mm)
1-1/4″ (32 mm)
1-1/4″ (32 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1-1/4″ (32 mm)
1″ (25 mm)
1-1/4″ (32 mm)
1″ (25 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1/2″ (13 mm)
1-1/2″ (38 mm)
1-1/4″ (32 mm)
1-1/2″ (38 mm)
1″ (25 mm)
3/4″ (19 mm)
1/2″ (13 mm)
1/2″ (13 mm)
Wire size is based on THHN wire for branch circuit protection at .91 derate factor. Circuit breakers and fused disconnects are to
be mounted remote and wired by contractor. Sizes are based on the 2002 NEC table 310-16. Conduit size based on conductors
plus ground wire sizing per Table C1 from appendix C.
Only 6, 7 and 9 kW models can be field converted to single or three phase (open delta on 3 phase). Check wiring diagram supplied
with the unit when converting the phase of the unit. Larger branch circuit required than for balanced 3 phase of equal kW. Balanced
3 phase available, consult factory.
Form No. EBOOSTERm-0712
7
SPECIFICATIONS
Circuit Breaker and Fused Disconnect Switch Sizes — 36 to 57 kW
kW
36
volts
208
208
240
240
39
40
40.5
45
54
57
380
480
600
Phase
1
3
1
3
3
3
3
L1
173
100
150
86.7
54.7
43.3
34.7
Amp Draw
L2
173
100
150
86.7
54.7
43.3
34.7
208
208
240
240
380
480
600
1
3
1
3
3
3
3
187.5
108
163.5
94
59.3
47
37.6
187.5
108
163.5
94
59.3
47
37.6
208
240
480
600
3
3
3
3
112.5
97.5
48.8
39
208
240
380
480
3
3
3
3
150
130
82
65
208
240
380
480
600
3
3
3
3
3
208
208
240
240
380
480
600
600
3
3
1
3
3
3
3
3
61.6
125
188
108
68.6
54
43.4
52
158.4
137.3
86.7
68.6
54.9
L3
Breaker or Fuse
Size
86.7
125
-100
--
225
125
200
54.7
43.3
34.7
70
60
50
Copper Wire
Size
Conduit Size
1
1-1/4″ (32 mm)
4/0
1
3/0
4
6
8
1-1/2″ (38 mm)
1-1/4″ (32 mm)
1-1/2″ (38 mm)
1″ (25 mm)
3/4″ (19 mm)
1/2″ (13 mm)
-108
-94
59.3
47
37.6
250
150
225
125
90
60
50
250 kcmil
1/0
4/0
1
3
6
8
2″ (51 mm)
1-1/4″ (32 mm)
2″ (51 mm)
1-1/4″ (32 mm)
1″ (25 mm)
3/4″ (19 mm)
1/2″ (13 mm)
112.5
97.5
48.8
39
112.5
97.5
48.8
39
150
125
70
50
1/0
1
4
8
1-1/4″ (32 mm)
1-1/4″ (32 mm)
1″ (25 mm)
3/4″ (19 mm)
150
130
82
65
150
130
82
65
200
175
125
90
158.4
137.3
86.7
68.6
54.9
200
175
125
90
70
61.6
125
188
108
68.6
54
43.4
52
158.4
137.3
86.7
68.6
54.9
61.6
90
125
-108
68.6
54
43.4
52
3
175
250
150
90
70
60
2/0
250 kcmil
1/0
3
4
6
70
4
1″ (25 mm)
1-1/2″ (38 mm)
2″ (51 mm)
1-1/4″ (32 mm)
1″ (25 mm)
1″ (25 mm)
3/4″ (19 mm)
3/0
2/0
1
3
2″ (51 mm)
1-1/2″ (38 mm)
1-1/4″ (32 mm)
1″ (25 mm)
3/0
2/0
1
3
4
2″ (51 mm)
1-1/2″ (38 mm)
1-1/4″ (32 mm)
1″ (25 mm)
1″ (25 mm)
1″ (25 mm)
The shaded area contains electrical information for International models only.
Wire size is based on THHN wire for branch circuit protection at .91 derate factor. Circuit breakers and fused disconnects are to
be mounted remote and wired by contractor. Sizes are based on the 2002 NEC table 310-16. Conduit size based on conductors
plus ground wire sizing per Table C1 from appendix C.
NOTE: 250 kcmil maximum wire size for terminal block.
WARNING
ELECTRIC SHOCK HAzARD: Consult a licensed electrical
contractor for proper electrical installation conforming to
local electrical codes and the National Electrical Code
(N.E.C.).
8
Form No. EBOOSTERm-0712
SPECIFICATIONS
Sizing Chart for Low-Temp Dish Machines
BOOSTERS RATED AT 30°F (16°C) RISE
Dish Machine Model Number
american Dish
Service
Blakeslee
Champion
Cma
Dish machines
Hobart
Jackson
Electric
Compact
Booster
aH, aH-3D, aH-3D-S, aHC, aHC-3D, aHC-3D-S, ET-a, ET-aF, ET-aH,
ET-a-m, ET-aH-m, ET-a-3, ET-aH-3, L-90-3D, L-90-3D-K, L-90-3D-K-S,
L-90-3D-S, L-90-3DC, L-90-3DC-K, L-90-3DC-K-S, L-90-3DC-S, L-90-3DW,
L-90-3DW-K, L-90-3DW-K-S, L-90-3DW-S, L-90-3DWC, L-90-3DWC-K,
L-90-3DWC-K-S, L-90-3DWC-S, WH, WHC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4
a-3D, a-3D-S, a, aC, aC-3D, aC-3D-S, aH-B, ET-aF-3, ET-aF-m, HT-25,
L-60-3D, L-60-3D-K, L-60-3D-K-S, L-60-3D-S, L-60-3DC, L-60-3DC-K,
L-60-3DC-K-S, L-60-3DC-S, L-60-3DW, L-60-3DW-K, L-60-3DW-K-S,
L-60-3DW-S, L-60-3DWC, L-60-3DWC-K, L-60-3DWC-K-S, L-60-3DWC-S,
L-72-3D, L-72-3D-K, L-72-3D-K-S, L-72-3D-S, L-72-3DC, L-72-3DC-K,
L-72-3DC-K-S, L-72-3DC-S, L-72-3DW, L-72-3DW-K, L-72-3DW-K-S,
L-72-3DWC-S, L-72-3DWC, L-72-3DWC-K, L-72-3DWC-K-S, L-72-3DWC-S,
W, WC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-5
a-B, aD-25, SS-25, 5-aH, 5-aHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-6
aF, aF-3D, aF-3D-S, aF-B, aFC, aFC-3D, aFC-3D-S, aFW, aFWC, 5, 5-S . . . . . . . .C-7
aDC-44, aDC-66, 5-aG, 5-aGS, 5-CD-LF, 5-CD-RF . . . . . . . . . . . . . . . . . . . . . . . . . .C-9
Imperial
Booster
. . . . . . . .S-6
. . . . . . . .S-6
. . . . . . . .S-6
. . . . . . . .S-7
. . . . . . . .S-9
U21-C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .S-6
D-8-LT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-6 . . . . . . . .S-6
DD-8-LT, R-CC64-LT, R-EE-LT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-12 . . . . . . .S-12
Series XF-EE-LT, XF-PEE-LT, XF-LL-LT, XF-PLL-LT, XF-mm-LT, XF-Pmm-LT,
XF-EEE-LT, XF-LLL-LT, XF-mmm-LT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-13 . . . . . . .S-13
Series R-L-LT, R-PL-LT, R-m-LT, R-Pm-LT, F-L-LT, F-PL-LT, F-m-LT,
F-Pm-LT (single tank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . . .S-36
Series “R” & “F”-CC-LT, -EE-LT, -LL-LT, -mm-LT, -LLL-LT, -mmm-LT, -PCC-LT,
-PEE-LT, -PLL-LT, -Pmm-LT (multi-tank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .S-24
Series XF-L-LT, XF-PL-LT, XF-m-LT, XF-Pm-LT (single tank) . . . . . . . . . . . . . . . . . . .C-54 . . . . . . .S-54
Series XF-PEE-LT, XF-PLL-LT, XF-Pmm-LT, XF-EEE-LT, XF-LLL-LT,
XF-mmm-LT (multi-tank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . . .S-36
Fa (Flight-a-Round) and Ra (Rack-a-Round) use comparable “F” listing.
ULD, ULF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-6 . . . . . . . .S-6
DLF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-13 . . . . . . .S-13
KL44, KL66 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . . .S-36
a-1, aH-1, C-1, VaC-1, a-3, aH-3, C-3, L-1C, VaC-3, VaC-4, VaC-5, L-1X . . . . . . . .C-4 . . . . . . . .S-6
a-2, aH-1, aH-2, aH-3, B-3, C-1, C-2, C-3, EVa-1, EVa-2, EVa-3, EVa-4,
EVa-5, VaC-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-6 . . . . . . . .S-6
B-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .S-7
B-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-9 . . . . . . . .S-9
Cma-44L with tank heater, Cma-66L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .S-24
CVa-1, CVa-2, CVa-3, CVa-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-6 . . . . . . . .S-6
CVa-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .S-7
LX-18C, LX-30C, LX-40C, Wm-5C, SR24C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .S-6
LT-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-6 . . . . . . . .S-6
am-14, am-14C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .S-7
C44a, CRS66a, CPW80a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-27 . . . . . . .S-27
FT-800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-30 . . . . . . .S-30
Conserver 24LT, 200LT, ES1000, (Ecolab/Jackson) . . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .S-6
Conserver 1, Conserver XL, ES2000 (Ecolab/Jackson) . . . . . . . . . . . . . . . . . . . . . . .C-9 . . . . . . . .S-9
Conserver 2, Conserver XL2, ES4000 (Ecolab/Jackson) . . . . . . . . . . . . . . . . . . . . . .C-15 . . . . . . .S-15
aJ-44, aJ-66, aJ-80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-18 . . . . . . .S-18
Knight Equipment
LTD.
KLE-112-HL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-5 . . . . . . . .S-6
Form No. EBOOSTERm-0712
9
SPECIFICATIONS
Booster Heater Sizing Chart
Dish Machine
adamation
alvey
american Dish
Service
Blakeslee
Champion
ELECTRIC
COMPACT BOOSTER
Temperature Rise
Model Number
40°F (22°C)
ELECTRIC
IMPERIAL BOOSTER
Temperature Rise
70°F (39°C) 40°F (22°C) 70°F (39°C)
CSL-1390, Ca-2, Ca-3, Ca-4, SLaP 44 . . . . . . . . . . . . . . . . . .C-39 . . . . . .(2)C-36 . . . . .S-39 . . . . .(2)S-36
Ca, Ca-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-54 . . . . . .(2)C-45 . . . . .S-54 . . . . .(2)S-45
FLC-10, SL-2S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--FLC-12, CL-1, CL-1 Turntable, Sa-5a . . . . . . . . . . . . . . . . . . . .--FL-2S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--KS-70, KS70m SB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--SL-2D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--FLC-36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--KS-88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--KS-70-N, KS-88-N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .---
. . . . . . . . .--. . . . . . . . .--. . . . . . . . .--. . . . . . . . .--. . . . . . . . .--. . . . . . . . .--. . . . . . . . .--. . . . . . . . .---
. . . . . . . .S-6 . . . . . . .S-9
. . . . . . . .S-7 . . . . . . .S-12
. . . . . . . .S-9 . . . . . . .S-13
. . . . . . . .S-9 . . . . . . .S-15
. . . . . . .S-13 . . . . . .S-18
. . . . . . .S-15 . . . . . .S-27
. . . . . . .S-18 . . . . . .S-30
. . . . . . .S-39 . . . . . . .---
HT-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .C-12 . . . . . . .S-7 . . . . . . .S-12
aCD-44, aDC-66 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-12 . . . . . . .C-24 . . . . . .S-12 . . . . . .S-24
UC-21a, UC-21B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .C-4 . . . . . . .S-6 . . . . . . .S-6
UC-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-6 . . . . . . . .C-12 . . . . . . .S-6 . . . . . . .S-12
D-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-9 . . . . . . . .C-13 . . . . . . .S-9 . . . . . . .S-13
D-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-12 . . . . . . .C-17 . . . . . .S-12 . . . . . .S-17
Series “R” & “F” -CC, -EE, -LL, -mm, -LLL, -mmm, -PCC,
-PEE, -PLL, -Pmm (multi-tank) with suffix “LC” . . . . . . . . . . .C-13 . . . . . . .C-24 . . . . . .S-13 . . . . . .S-24
Series XF-EE, XF-LL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-17 . . . . . . .C-30 . . . . . .S-17 . . . . . .S-30
Series XF-LL, XF-PLL, XF-mm, XF-Pmm, XF-EEE, XF-LLL,
XF-mmm (multi-tank) with suffix “LC” . . . . . . . . . . . . . . . . . . .C-17 . . . . . . .C-30 . . . . . .S-17 . . . . . .S-30
DD-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-18 . . . . . . .C-30 . . . . . .S-18 . . . . . .S-30
Series F-E, Fa-EE, Fa-PEE, Fa-LL, Fa-PLL, Fa-mm,
Fa-Pmm, F-EEE, Fa-EEE, Fa-LLL, Fa-mmm, F-PE . . . . . . .C-30 . . . . . . .C-54 . . . . . .S-30 . . . . . .S-54
Series R-L, R-PL, R-m, R-Pm, F-L, F-PL, F-m,
F-Pm (single tank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . . .C-54 . . . . . .S-36 . . . . . .S-54
Series XF-L, XF-PL, XF-m, XF-Pm, (single tank) . . . . . . . . . .(2)C-36 . . . . . . .--- . . . . . .(2)S-36 . . . . . .--Series R-E, R-PE, XF-PEE, XF-PLL, XF-Pmm, XF-EEE,
XF-LLL, XF-mmm (multi-tank) . . . . . . . . . . . . . . . . . . . . . . . .C-45 . . . . . .(2)C-30 . . . . .S-45 . . . . .(2)S-30
Fa (Flight-a-Round) and Ra (Rack-a-Round) use comparable “F” listing.
U-H1, UH-200, UH-200B, U-HB . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .C-6 . . . . . . .S-6 . . . . . . .S-6
UL-150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .C-7 . . . . . . .S-6 . . . . . . .S-7
UH-150, UH-150B, UH-100, UH-100B, DHB-VS . . . . . . . . . . . .C-5 . . . . . . . .C-9 . . . . . . .S-6 . . . . . . .S-9
D-H1, D-HB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-6 . . . . . . . .C-12 . . . . . . .S-6 . . . . . . .S-12
D-H1T, D-HBT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .C-12 . . . . . . .S-7 . . . . . . .S-12
44 DRWS, 66 DRPWWS, 80 DRHDPWWS, 70 DRFFPWWS .C-9 . . . . . . . .C-13 . . . . . . .S-9 . . . . . . .S-13
PP-28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-9 . . . . . . . .C-15 . . . . . . .S-9 . . . . . . .S-15
D-H1C, D-H1TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-9 . . . . . . . .C-18 . . . . . . .S-9 . . . . . . .S-18
44 DR, 66 DRPW, 80 DRHDFW, 70 DRFFPW . . . . . . . . . . . . .C-12 . . . . . . .C-24 . . . . . .S-12 . . . . . .S-24
66 WSPW, 44-WS, 66-WS, 64, 90FFPW, 100HDPW,
86 PW, 84, 106 PW,120 HDPW, 110 FFPW . . . . . . . . . . . . . .C-13 . . . . . . .C-24 . . . . . .S-13 . . . . . .S-24
UC-CW6-WS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-36 . . . . . .S-24 . . . . . .S-36
US-CW8-WS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-39 . . . . . .S-24 . . . . . .S-39
44, 66 PW, 70FFPW, 80HDPW, 54, 76PW, 80FFPW,
90HDPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-45 . . . . . .S-24 . . . . . .S-45
40-KB, 40-KB-2-2, 40-KFWB, 40-KPRB, 40KPRB-2-2,
40KPRB-2-3, 60-KB, 60-KB-2-2, 60-KFWB, 60-KFWB-2-2,
60-KPRB, 60-KPRB-2-3, 64KB, 64-KB Corner, 64-KPRB,
64-KPRB Corner, 64 modular, 86 modular . . . . . . . . . . . . . . .C-30 . . . . . . .C-54 . . . . . .S-30 . . . . . .S-54
44-KB, 44-KB Corner, 44-KPRB, 44-KPRB Corner, 54-KB,
54-KB Corner, 54-KPRB, 54-KPRB Corner, 44 modular,
66 PW modular, UC** Series 6' Center, UC-C4 . . . . . . . . . . .C-36 . . . . . . .C-57 . . . . . .S-36 . . . . . .S-57
UC-CW4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . .(2)C-36 . . . . .S-36 . . . . .(2)S-36
UC-C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-45 . . . . . .(2)C-36 . . . . .S-45 . . . . .(2)S-36
UC**CW Series 6' Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-45 . . . . . .(2)C-39 . . . . .S-45 . . . . .(2)S-40
W-6-WS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-45 . . . . . .(2)C-45 . . . . .S-45 . . . . .(2)S-40
10
Form No. EBOOSTERm-0712
SPECIFICATIONS
Booster Heater Sizing Chart (continued)
Dish Machine
Cma
Dish machines
Hobart
Insinger
ELECTRIC
COMPACT BOOSTER
Temperature Rise
Model Number
40°F (22°C)
ELECTRIC
IMPERIAL BOOSTER
Temperature Rise
70°F (39°C) 40°F (22°C) 70°F (39°C)
Cma-180 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .C-12 . . . . . . .S-7 . . . . . . .S-12
Cma-44H with tank heater, Cma-66H . . . . . . . . . . . . . . . . . . .C-36 . . . . . . .C-45 . . . . . .S-36 . . . . . .S-45
am-15F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .C-6 . . . . . . .S-6 . . . . . . .S-6
LXiC, LXiGC, LX-18C, LX-30C, LX-40C . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .C-7 . . . . . . .S-6 . . . . . . .S-6
LX-30, SR24, SR24H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .C-7 . . . . . . .S-6 . . . . . . .S-7
LX-18, am-14F, am-15, am-15T . . . . . . . . . . . . . . . . . . . . . . . .C-5 . . . . . . . .C-9 . . . . . . .S-6 . . . . . . .S-9
Wm-5C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-6 . . . . . . . .C-9 . . . . . . .S-6 . . . . . . .S-9
Wm-5 (without sump heater) . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .C-12 . . . . . . .S-7 . . . . . . .S-12
am-14T, am-14TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .C-12 . . . . . . .S-7 . . . . . . .S-12
am-14, am-14C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-9 . . . . . . . .C-12 . . . . . . .S-9 . . . . . . .S-12
am-12, am-12C* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-9 . . . . . . . .C-12 . . . . . . .S-9 . . . . . . .S-12
UW-50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .--- . . . . . . .S-15 . . . . . .S-24
or Opti-Rinse C44a, CRS-66a, CCS-66a, CPW-80a, C54a,
CRS-76a, CCS-76a, CPW-90a, C64a, CRS-86a, CCS-86a,
CPW-100a, C-88a, CRS-110a, CCS-110a, CPW-124a . . . .C-15 . . . . . . .C-27 . . . . . .S-15 . . . . . .S-27
C-54a, CRS-76a, CPW-90a, CCS-76a . . . . . . . . . . . . . . . . . .C-39 . . . . . .(2)C-36 . . . . .S-30 . . . . .(2)S-36
C-44a, CRS-66a, CCS-66a, CPW-80a, C-64a, CRS-86a,
CCS-86a, CPW-100a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-30 . . . . . . .C-54 . . . . . .S-30 . . . . . .S-54
C-88a, CRS-110a, CPW-124a, CCS-110a . . . . . . . . . . . . . . .C-36 . . . . . . .C-54 . . . . . .S-36 . . . . . .S-54
or Opti-Rinse C44aW, CRS-66aW, CCS-66aW, CPW-80aW . .C-9 . . . . . . . .C-15 . . . . . . .S-9 . . . . . . .S-15
C-44aW, CRS-66aW, CPW-80aW, CCS-66aW . . . . . . . . . . . .C-12 . . . . . . .C-24 . . . . . .S-12 . . . . . .S-24
C-44, CRS-66, CPW-80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . . .C-54 . . . . . .S-36 . . . . . .S-54
C-54, CRS-76, CPW-90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-54 . . . . . .(2)C-39 . . . . .S-54 . . . . .(2)S-39
C-64W, CRS-86W, CPW-100W, C-88W, CRS-110W,
CPW-124W, CCS-86W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-36 . . . . . .S-24 . . . . . .S-36
C-64, CRS-86, CPW-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-45 . . . . . .(2)C-36 . . . . .S-45 . . . . .(2)S-36
FT800W, FT-900W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-39 . . . . . .S-24 . . . . . .S-39
FT-600, FT-700 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-54 . . . . . .(2)C-39 . . . . .S-54 . . . . .(2)S-39
FT800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-39 . . . . . .(2)C-39 . . . . .S-39 . . . . .(2)S-39
Opti-Rinse* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . . .C-57 . . . . . .S-36 . . . . . .S-57
FT800S, FT-900S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-39 . . . . . .(2)C-36 . . . . .S-39 . . . . .(2)S-36
UTW-28, UTW-28C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .--- . . . . . . .S-18 . . . . . .S-36
FRC and FR (Fast Rack Series) use comparable “C” line listing.
GS 302, GS-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .C-4 . . . . . . .S-6 . . . . . . .S-6
45Sa-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .C-7 . . . . . . .S-6 . . . . . . .S-7
Commander 18-5C, 18-5CH, CS-5, CS-5C, CS-5CH, CS-5H . .C-6 . . . . . . . .C-12 . . . . . . .S-6 . . . . . . .S-12
Commander 18-5, 18-5H, Ensign 40-2 . . . . . . . . . . . . . . . . . . .C-6 . . . . . . . .C-12 . . . . . . .S-6 . . . . . . .S-12
admiral 44-4, 66-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-36 . . . . . .S-24 . . . . . .S-39
135-20, 185-20, 250-20, 60-20, 85-20, R-106-2 . . . . . . . . . . . .C-24 . . . . . . .C-25 . . . . . .S-24 . . . . . .S-45
Speeder 64, 86-3, Century (all), Super 106-2 . . . . . . . . . . . . . .C-24 . . . . . . .C-45 . . . . . .S-24 . . . . . .S-45
Trac 878 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-36 . . . . . .S-24 . . . . . .S-36
Century 14, Clipper RC-##-RPW-W . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-39 . . . . . .S-24 . . . . . .S-39
Clipper (all), R106-2, Super 106-2, Trac 321, Trac 321-2/RPW C-27 . . . . . . .C-45 . . . . . .S-27 . . . . . .S-45
Defender-(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-30 . . . . . . .C-54 . . . . . .S-30 . . . . . .S-54
Defender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . . .C-54 . . . . . .S-36 . . . . . .S-54
master (all) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . . .C-57 . . . . . .S-36 . . . . . .S-57
Ca-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .--- . . . . . . . .S-9 . . . . . . .S-24
Da-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .--- . . . . . . .(2)S-9 . . . . .(2)S-24
For outdated models, consult factory for correct booster.
* Hobart model am-12 with serial no. 12-067-357 or below and model am-12C with serial no. 12-067-537 or below require slightly
larger booster than listed. ‘C’ models with serial no. 85-1041605 or greater use Opti-Rinse.
Shaded area indicates older models prior to Opti-Rinse.
Form No. EBOOSTERm-0712
11
SPECIFICATIONS
Booster Heater Sizing Chart (continued)
Dish machine
Jackson
Knight
Equipment LTD.
meiko
ELECTRIC
COMPACT BOOSTER
Temperature Rise
Model Number
40°F (22°C)
ELECTRIC
IMPERIAL BOOSTER
Temperature Rise
70°F (39°C) 40°F (22°C) 70°F (39°C)
JP-24, JP-24B, JP-24F, JP-24BF . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .C-6 . . . . . . .S-6 . . . . . . .S-6
24B Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .C-4 . . . . . . . .--- . . . . . . . .S-6
10aB, 10aPRB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .C-5 . . . . . . . .--- . . . . . . . .S-6
44CE*, 66 CERPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-30 . . . . . . .C-54 . . . . . .S-30 . . . . . .S-54
54CE, 76 CERPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . .(2)C-30 . . . . .S-36 . . . . .(2)S-30
64CE, 86 CERPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-27 . . . . . . .C-39 . . . . . .S-27 . . . . . .S-39
100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-12 . . . . . . .C-24 . . . . . .S-12 . . . . . .S-24
100B, 100PRB, 150B, 150PRB . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .C-9 . . . . . . . .--- . . . . . . . .S-9
150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-12 . . . . . . .C-18 . . . . . .S-12 . . . . . .S-18
200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .C-12 . . . . . . .S-7 . . . . . . .S-12
200B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .C-6 . . . . . . . .--- . . . . . . . .S-6
Tempstar, Tempstar SDS, Tempstar HH . . . . . . . . . . . . . . . . . . .C-6 . . . . . . . .C-12 . . . . . . .S-6 . . . . . . .S-12
TS-44, TS-66 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-36 . . . . . .S-24 . . . . . .S-36
aJ-44, aJ-66, aJ-80, WH-44, ES-4400,
ES-6600 (Ecolab/Jackson) . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-45 . . . . . .S-24 . . . . . .S-45
aJ-54, aJ-76, aJ-90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . .(2)C-36 . . . . .S-36 . . . . .(2)S-36
aJ-64, aJ-86, aJ-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-39 . . . . . .S-24 . . . . . .S-39
*model #44CE w/SN1999 or below requires larger booster than listed.
KLE-112-HL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .C-12 . . . . . . .S-7 . . . . . . .S-12
K-44, K-66, K-80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-36 . . . . . .S-24 . . . . . .S-36
K-54, K-76, K-90, K-64, K-86, K-100 . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-45 . . . . . .S-24 . . . . . .S-45
metalwash/Intedge FW4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-12 . . . . . . .C-18 . . . . . .S-12
RS-30a, RS-28L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .--- . . . . . . .S-15
RT-74, RT-60, RT-42B, RT-42BC . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .--- . . . . . . .S-27
RS-2R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .--- . . . . . . .S-30
12
. . . . . .S-18
. . . . . .S-24
. . . . . .S-40
. . . . . .S-45
Form No. EBOOSTERm-0712
SPECIFICATIONS
Booster Heater Sizing Chart (continued)
Dish machine
Stero
ELECTRIC
COMPACT BOOSTER
Temperature Rise
Model Number
40°F (22°C)
ELECTRIC
IMPERIAL BOOSTER
Temperature Rise
70°F (39°C) 40°F (22°C) 70°F (39°C)
SCT-44-10-LW, SCT-44-LW, SCT-66S-LW, SCT-76S-LW,
SCT-76SC-LW, SCT-90S-LW . . . . . . . . . . . . . . . . . . . . . . . . .C-12 . . . . . . .C-24 . . . . . .S-12 . . . . . .S-24
SC-1-2-4-LW, SC-1-6-4-LW, SC-2-4-LW, SC-5-2-4-LW,
SC-5-6-4-LW, SC-6-4-LW . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-45 . . . . . .S-24 . . . . . .S-45
SCT-64, SCT-86S, SCT-94S, SCT-94SC . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-39 . . . . . .S-24 . . . . . .S-39
SCT-108S, SCT-108SC, SCT-76, SCT-94Sm . . . . . . . . . . . . . .C-27 . . . . . . .C-54 . . . . . .S-27 . . . . . .S-54
SC-6-4, SCT-44, SCT-44-10, SCT-66S, SCT-76S,
SCT-76SC, SCT-90S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-30 . . . . . . .C-54 . . . . . .S-30 . . . . . .S-54
SCT-120S, SCT-120SC, SCT-120Sm, SCT-150Sm . . . . . . . . .C-36 . . . . . . .C-57 . . . . . .S-36 . . . . . .S-57
STW-110, SC-1-2-7-4, SC-1-6-3-4, SC-1-6-7-4, SC-2-7-4,
SC-5-2-7-4, SC-5-6-3-4, SC-5-6-7-4, SC-6-3-4, SC-6-7-4 . . .C-39 . . . . . .(2)C-36 . . . . .S-39 . . . . .(2)S-39
SC-1-2-4, SC-1-6-4, SC-2-4, SC-5-2-4, SC-5-6-4 . . . . . . . . . .C-45 . . . . . .(2)C-36 . . . . .S-45 . . . . .(2)S-45
SCT-44-10-SC-1-3-4, SCT-44-10-3-4, SCT-44-SC-1-3-4,
SCT-44-SC-3-4, SCT-54-SC-1-3-4, SCT-54-SC-3-4,
SCT-76S-SC-3-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-45 . . . . . .(2)C-36 . . . . .S-40 . . . . .(2)S-36
STPC (Four tank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-39 . . . . . .S-24 . . . . . .S-39
STPCW (Four tank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-24 . . . . . . .C-45 . . . . . .S-24 . . . . . .S-40
STPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-27 . . . . . . .C-54 . . . . . .S-27 . . . . . .S-54
STPCW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . .(2)C-30 . . . . .S-36 . . . . .(2)S-30
SCBT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-45 . . . . . .(2)C-36 . . . . .S-40 . . . . .(2)S-36
SF-1Ra, SC20-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7 . . . . . . . .C-12 . . . . . . .S-7 . . . . . . .S-12
SF-2Ra, SF-2DRa, SD-2Ra, SDRa, SDRa-PaCK . . . . . . . . .C-12 . . . . . . .C-18 . . . . . .S-12 . . . . . .S-18
SCT-54, SCT-76Sm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-36 . . . . . . .C-57 . . . . . .S-36 . . . . . .S-57
SCT-76, SCT-80, SCT-94, SCT-108, SCT-120 . . . . . . . . . . . . .C-45 . . . . . . .C-57 . . . . . .S-45 . . . . . .S-57
U-31-a, U-31-aC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . .--- . . . . . . .S-18 . . . . . .S-36
U-31-a2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-45 . . . . . .(2)C-36 . . . . .S-45 . . . . .(2)S-36
STBUW-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-57 . . . . . .(2)C-54 . . . . .S-57 . . . . .(2)S-54
SC-2-3-4, SC-5-2-3-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-30 . . . . . .(2)C-27 . . . . .S-30 . . . . .(2)S-27
SC20-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-12 . . . . . . .C-24 . . . . . .S-12 . . . . . .S-24
SC-2-8, SC-2-9, SC-1-2-8, SC-5-6-8, SC-6-8, SC-6-9,
SC-1-6-8, SC-5-6-9, SC-5-2-9, SC-1-6-9, SC-5-2-8 . . . . . . . .C-18 . . . . . . .C-36 . . . . . .S-18 . . . . . .S-36
This selector chart is based on 40°F (22°C) and 70°F (39°C) temperature rises, 20 psi flow pressure, and minimum rinse cycle timer
setting in NSF listing.
all booster heaters are rated at 100% of the capacity of the dish machines as recommended by the National Sanitation Foundation.
Where make-up water for wash tank is provided from final rinse supply, chart recommendations are based upon this additional
demand (not over 2 GPm) as required by NSF.
NOTE: All sizings shown are that of the dish machine manufacturers. Hatco Corporation is not responsible for incorrect sizing
applications.
Form No. EBOOSTERm-0712
13
SPECIFICATIONS
Capacity — Imperial “S” Series
Model
kW
40°F (22°C) Rise
70°F (39°C) Rise
S-12
S-13
S-15
12
13.5
15
120 gph (454 lph)
135 gph (511 lph)
151 gph (572 lph)
69 gph (261 lph)
77 gph (292 lph)
86 gph (326 lph)
S-27
S-30
S-36
27
30
36
271 gph (1026 lph)
301 gph (1139 lph)
361 gph (1367 lph)
155 gph (587 lph)
172 gph (651 lph)
206 gph (780 lph)
54
57
542 gph (2052 lph)
573 gph (2169 lph)
310 gph (1174 lph)
326 gph (1234 lph)
S-6
S-7
S-9
S-17
S-18
S-24
S-39
S-40
S-45
S-54
S-57
6
7
9
17.2
18
24
39
40.5
45
60 gph (227 lph)
70 gph (265 lph)
90 gph (341 lph)
173 gph (655 lph)
181 gph (685 lph)
241 gph (912 lph)
391 gph (1480 lph)
407 gph (1541 lph)
452 gph (1711 lph)
Storage Capacity
Shipping Weight
16 gallons (61 liters)
16 gallons (61 liters)
16 gallons (61 liters)
200 lbs. (91 kg)
200 lbs. (91 kg)
200 lbs. (91 kg)
34 gph (129 lph)
40 gph (151 lph)
52 gph (197 lph)
16 gallons (61 liters)
16 gallons (61 liters)
16 gallons (61 liters)
99 gph (375 lph)
103 gph (390 lph)
138 gph (522 lph)
16 gallons (61 liters)
16 gallons (61 liters)
16 gallons (61 liters)
224 gph (848 lph)
232 gph (878 lph)
258 gph (977 lph)
16 gallons (61 liters)
16 gallons (61 liters)
16 gallons (61 liters)
16 gallons (61 liters)
16 gallons (61 liters)
16 gallons (61 liters)
200 lbs. (91 kg)
200 lbs. (91 kg)
200 lbs. (91 kg)
200 lbs. (91 kg)
200 lbs. (91 kg)
214 lbs. (97 kg)
214 lbs. (97 kg)
214 lbs. (97 kg)
214 lbs. (97 kg)
214 lbs. (97 kg)
224 lbs. (102 kg)
224 lbs. (102 kg)
16 gallons (61 liters)
16 gallons (61 liters)
224 lbs. (102 kg)
224 lbs. (102 kg)
Capacity — Compact “C” Series
Model
kW
40°F (22°C) Rise
70°F (39°C) Rise
Storage Capacity
Shipping Weight
C-7
C-9
C-12
7
9
12
70 gph (265 lph)
90 gph (341 lph)
120 gph (454 lph)
40 gph (151 lph)
52 gph (197 lph)
69 gph (261 lph)
6 gallons (23 liters)
6 gallons (23 liters)
6 gallons (23 liters)
118 lbs. (54 kg)
118 lbs. (54 kg)
120 lbs. (54 kg)
18
24
27
181 gph (685 lph)
241 gph (912 lph)
271 gph (1026 lph)
103 gph (390 lph)
138 gph (522 lph)
155 gph (587 lph)
45
54
57
452 gph (1711 lph)
542 gph (2052 lph)
573 gph (2169 lph)
258 gph (977 lph)
310 gph (1174 lph)
326 gph (1234 lph)
C-4
C-5
C-6
4
5
6
C-13
C-15
C-17
13
15
17
C-30
C-36
C-39
30
36
39
C-18
C-24
C-27
C-45
C-54
C-57
40 gph (151 lph)
50 gph (189 lph)
60 gph (227 lph)
135 gph (511 lph)
151 gph (572 lph)
173 gph (655 lph)
301 gph (1139 lph)
361 gph (1367 lph)
391 gph (1480 lph)
23 gph (87 lph)
29 gph (110 lph)
34 gph (129 lph)
77 gph (292 lph)
86 gph (326 lph)
99 gph (375 lph)
172 gph (651 lph)
206 gph (780 lph)
224 gph (848 lph)
kW
40°F (22°C) Rise
70°F (39°C) Rise
mC-10.5
10.4
104 gph (393 lph)
60 gph (227 lph)
mC-15
15
150 gph (568 lph)
mC-11
mC-17
9.9
11.4
17.25
99 gph (375 lph)
114 gph (432 lph)
120 lbs. (54 kg)
120 lbs. (54 kg)
120 lbs. (54 kg)
6 gallons (23 liters)
6 gallons (23 liters)
6 gallons (23 liters)
142 lbs. (64 kg)
142 lbs. (64 kg)
142 lbs. (64 kg)
6 gallons (23 liters)
6 gallons (23 liters)
6 gallons (23 liters)
6 gallons (23 liters)
6 gallons (23 liters)
6 gallons (23 liters)
173 gph (655 lph)
3.2 gallons (12 liters)
48 lbs. (22 kg)
65 gph (248 lph)
3.2 gallons (12 liters)
14
142 lbs. (64 kg)
142 lbs. (64 kg)
142 lbs. (64 kg)
Shipping Weight
3.2 gallons (12 liters)
99 gph (375 lph)
120 lbs. (54 kg)
142 lbs. (64 kg)
142 lbs. (64 kg)
Storage Capacity
57 gph (216 lph)
86 gph (326 lph)
105 lbs. (48 kg)
105 lbs. (48 kg)
118 lbs. (54 kg)
6 gallons (23 liters)
6 gallons (23 liters)
6 gallons (23 liters)
Capacity — Mini-Compact “MC” Series
Model
mC-10
6 gallons (23 liters)
6 gallons (23 liters)
6 gallons (23 liters)
3.2 gallons (12 liters)
3.2 gallons (12 liters)
48 lbs. (22 kg)
48 lbs. (22 kg)
48 lbs. (22 kg)
48 lbs. (22 kg)
Form No. EBOOSTERm-0712
SPECIFICATIONS
Dimensions — Imperial “S” Series
* Outlet, Inlet, and Knockout
are located on the bottom of unit.
Electrical Knockouts
bottom—1-1/2” and 2”
22-3/4”
(578 mm)
23-9/16”
(598 mm)
5”
(126 mm)
9-3/4”
(247 mm)
9-3/4”
(247 mm)
2-1/8”
2”
(55 mm)
(53 mm)
Outlet*
31-1/16”
(788 mm)
Inlet*
22-1/16”
(560 mm)
[
13-3/4”
(349 mm)
Front Side
3-5/8”
(92 mm)
Side View
Front View
Knockout*
3/4” Inlet Tee
4” (102 mm)
20-7/8”
(532 mm)
2-5/8”
(66 mm)
9-3/4”
(247 mm)
Top View
Dimensions — Compact “C” Series 4 to 18 kW
Electrical Knockouts left side
and bottom—3/4”, 1”, and 1-1/4”
5-5/16”
(134 mm)
6-1/2”
(166 mm)
Outlet
20-11/16”
(525 mm)
2-1/2”
(70 mm)
7-7/8”
(200 mm)
T/P Relief
Valve
19-13/16”
(502 mm)
13-1/16”
(332 mm)
* Knockout is located
on the bottom of unit.
Inlet
Knockout*
10-3/8”
(262 mm)
Rear View
Form No. EBOOSTERm-0712
12-3/4”
(322 mm)
Side View
15
2-3/4”
(69 mm)
2-3/4” (69 mm)
3-1/8”
(79 mm)
Top View
SPECIFICATIONS
Dimensions — Compact “C” Series 24 to 57 kW
2-1/16”
(54 mm)
7-7/8”
(200 mm)
24”
(610 mm)
5-5/16”
(134 mm)
6”
(152 mm)
18”
(457 mm)
* Knockout is located
on the bottom of unit.
Electrical Knockouts left side
and bottom—1-1/2” and 2”
Outlet
T/P Relief
Valve
18-1/16”
(458 mm)
Inlet
Knockout*
3” (75 mm)
15-3/16”
(387 mm)
16-1/8”
(410 mm)
2-3/4”
(69 mm)
3-3/8”
(85 mm)
Top View
Side View
Rear View
Dimensions — Mini-Compact “MC” Series
Electrical Knockouts—
1/2”, 3/4”, and 1”
3-1/8”
(79 mm)
12-7/8”
(327 mm)
T/P
Relief
Valve
* Knockout is located
on the bottom of unit.
11-3/4”
(298 mm)
5-1/2”
(139 mm)
18-1/2”
(469 mm)
T/P
Relief
Valve
4-3/8”
(138 mm)
Outlet
Inlet
Knockout*
9-1/8”
(232 mm)
8-1/8”
(206 mm)
1-3/8”
(34 mm)
Front Side
1-1/4”
(31 mm)
Front View
Side View
16
Top View
Form No. EBOOSTERm-0712
INSTALLATION
General
4. Place the unit in the appropriate location.
• The location must have a solid foundation along with
being clean and dry.
Booster Heaters are shipped with most components preassembled. Care should be taken when unpacking shipping
carton to avoid damage to unit and components enclosed.
Components are shipped with the heater unit.
• adequate front clearance is required to allow for
accessibility to the control compartment.
• Location must have adequate clearance to allow for
inspection, testing or replacement of pressure and/or
temperature relief valve.
WARNING
ELECTRIC SHOCK HAzARD:
• Unit must be installed by qualified, trained installers.
Installation must conform to all local electrical and
plumbing codes. Installation by unqualified personnel
will void the unit warranty and may lead to electric
shock or burn, as well as damage to unit and/or its
surroundings. Check with local plumbing and electrical
inspectors for proper procedures and codes.
• Install the booster heater as close as possible to the
commercial dish machine for efficient operation.
WARNING
Make sure the dishtable is strong enough to support the
weight of the booster heater and water when installing
with slide mounting brackets.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
Follow standard welding safety and operational
procedures when attaching sliderails to bottom of
dishtable.
• Do not place aftermarket covers on or over booster
heater. Doing so can cause temperature and moisture
build-up resulting in premature failure and electrical
shock.
5. Install unit under dishtable using mounting slide brackets,
if applicable (Compact Series only).
ExPLOSION HAzARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
a. Weld slide rails to bottom of dishtable.
b. Using Hatco slide brackets as a template, drill 1/8"
(3 mm) holes into the sides of the heater jacket.
Install booster water heater as close as possible to a
commercial dish machine. Employ re-circulation if
distance between water heater and dish machine exceeds
National Sanitation Foundation (NSF) specifications of
five (5) linear feet (1524 mm).
c. attach slide brackets to sides of heater with supplied
screws.
d. Slide heater onto slide rails under dishtable.
Install booster water heater in a horizontal position with
the base parallel to the floor and the inlet connection at
the lowest point. Improper installation could create an
unsafe condition.
Weld slide rail
to bottom of
dish table
1. Remove the unit from the box.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
ImPORTaNT OWNER INFORmaTION section for
details.
2. Remove tape and protective packaging from all surfaces
of unit.
Fasten slide
brackets to booster
heater sides
3. If unit is equipped with
legs, carefully lay unit
on its side and install
the four legs.
Hanging Support
NOTICE
Do not lay unit on the side with the control panel. Damage
to the unit could occur.
NOTE: If unit is not level, use an adjustable wrench to adjust
the foot of each leg until unit is level. Each leg is
adjustable from 6" (152 mm) to 7" (178 mm).
Compact Series Heater mounted to Dishtable
Form No. EBOOSTERm-0712
17
INSTALLATION
Plumbing Installation
Inlet
Use the following procedure to install the inlet assembly. Refer
to the appropriate “Plumbing Connections” diagram in this
section for more information.
WARNING
Do not connect booster water heaters to domestic
(consumer) dish machines or other domestic utilized
equipment. This booster may damage domestic equipment.
1. Connect the booster water inlet to a hot water supply line
from a normal water heater.
• Water temperature from the water heater should be
110°–140°F (43°–60°C) and should not exceed 160°F
(71°C). minimum temperature differential between inlet
and outlet should never be less than 30°F (-1°C).
Do not connect an expansion tank of any type to booster
heater water lines.
Use only plumbing material suitable for a minimum water
temperature of 200°F (93°C). Materials used must meet
National Sanitation Foundation (NSF) specifications and
all local plumbing codes and regulations.
NOTE: Refer to BOOSTER HEaTER SIzING CHaRT for
application information.
Refer to the BOOSTER HEATER SIzING CHART in this
manual to ensure proper sizing and avoid personal injury
and/or damage to the booster heater.
NOTE: The red mark on the inlet and outlet water pipes of
Compact series units must remain in the top most
position.
2. Install a shut-off valve (a full opening gate or ball type).
3. Install one of the temperature/pressure gauges.
CAUTION
Do not connect booster heater directly to a boiler or
furnace coil or any other uncontrolled temperature
source. The booster heater thermostat could be damaged
causing unit to overheat.
• When installing the temperature/pressure gauge, the
temperature sensing element must be in the water
stream and the gauge must be mounted upright.
NOTE: Tighten gauge during installation by turning the 1/2"
brass nut only. DO NOT turn the face of the gauge.
Turning the face will cause inaccurate measurements.
NOTICE
Use dielectric couplings when connecting dissimilar
metals, such as galvanized to copper. This will prevent
electrolysis or premature plumbing damage.
CAUTION
Hatco requires that two temperature/pressure gauges
(Hatco P/N 03.01.003.00) be installed to ensure proper
operation. Install one in the supply line before the
pressure reducing valve and one in the outlet line as close
to the booster heater as possible. This provides a visual
check of the water temperature and pressure before and
after the water heater.
DO NOT turn or adjust inlet water connection on Compact
Series Booster Heaters. Doing so will change the internal
water flow.
Do not back out or loosen any pipe fittings. Doing so may
cause leaks.
Do not lay unit on the side with the control panel. Damage
to the unit could occur.
NOTE: If a check valve is installed and cannot be removed,
install a back pressure relief valve (P/N 03.02.039.00) set
at 125 psi (862 kPa) on the incoming line between the
pressure reducing valve and the inlet to the booster
heater. Discharge must be to open site drain.
Incoming water in excess of 3 grains of hardness per
gallon (GPG) (0.75 grains of hardness per liter [GPL]) must
be treated and softened before being supplied to booster
heater(s). Water containing over 3 GPG (0.75 GPL) will
decrease efficiency, increase energy use, and reduce the
operating life of the unit through increased lime build-up.
Product failure caused by liming or sediment buildup is
not covered under warranty.
Do not use deionized water. Deionized water will shorten
the life of water reservoir and heating element.
NOTE: Product failure caused by liming or sediment buildup is
not covered under warranty.
NOTE: A 3/4" union and a drain valve are required for easy
servicing.
Temperature/Pressure Gauge
NOTE: An optional flow restrictor (P/N 03.02.074.00) is
available for installation on the water inlet line.
NOTE: Some dish machines require two booster heaters to be
plumbed in series (not parallel) to meet the demand.
To ensure proper operation, a 30°F (-1°C) temperature
differential must be maintained between the outlet of
the first booster heater and the inlet of the second
booster heater.
18
Form No. EBOOSTERm-0712
INSTALLATION
4. Install the pressure reducing valve if water pressure
available to the booster heater inlet is over 25 psi (172 kPa).
WARNING
Temperature/pressure protective equipment should not
be less than a combination temperature/pressure relief
valve certified by a nationally recognized testing
laboratory that maintains periodic inspection of the
production of this equipment and meets the requirements
for Relief valves and Automatic Shutoff Devices for Hot
Water Supply Systems, ANSI z21.22-1979. The
temperature/pressure relief valve must be marked with a
minimum set pressure not to exceed the marked
hydrostatic test pressure of the booster heater as noted
on the unit specifications.
• Set pressure reducing valve at 20 psi (138 kPa) flow
pressure.
NOTE: Be sure water flows through the pressure reducing
valve in the proper direction. Check directional arrow.
Valve will reduce pressure only during flow conditions.
CAUTION
If water supply pressure to the booster inlet is over 20 psi
(138 kPa) during flow, install pressure reducing valve with
built-in bypass (Hatco P/N 03.02.004.00) for proper
operation of dish machine rinse nozzles.
FOR INSTALLING PRESSURE AND TEMPERATURE
RELIEF vALvES IN ACCORDANCE WITH AMERICAN
NATIONAL STD. z21.22-1979. Combination pressure and
temperature relief valves with extension thermostats must
be installed so that the temperature-sensing element is
immersed in the water within the top 6" (152 mm) of the
tank. They must be installed directly in a tank tapping.
Combination pressure and temperature relief valves that
do not have extension elements must be mounted directly
in a tank tapping located within the top 6" (152 mm) of the
tank, and shall be adequately insulated and located so as
to assure isolation from ambient conditions that are not
indicative of stored water temperature. TO AvOID WATER
DAMAGE OR SCALDING DUE TO vALvE OPERATION,
DRAIN PIPE MUST BE CONNECTED TO vALvE OUTLET
AND RUN TO A SAFE PLACE OF DISPOSAL. Discharge
line must be as short as possible and be the same size as
the valve discharge connection throughout its entire
length. Drain line must pitch downward from the valve and
must terminate between 1-1/2" (38 mm) and 6" (152 mm)
above the floor drain where any discharge will be clearly
visible. The drain line shall terminate plain, not threaded,
with material serviceable for temperatures up to 250°F
(121°C) or greater. Excessive length, over 30' (9.1 m), or
use of more than four elbows can cause a restriction and
reduce the discharge capacity of the valve. No shut-off
valve shall be installed between the relief valve and tank,
or in the drain line. valve lever must be tripped
periodically to assure that waterways are clear. This
device is designated for emergency safety relief and shall
not be used as an operating control. The valves are set to
relieve at 150 psi (1034 kPa) or when water temperature
reaches 210°F (99°C). Read tag on valve for additional
information.
NOTE: The pressure reducing valve must be the type equipped
with a high pressure bypass, as supplied by Hatco.
Pressure Reducing Valve
5. Install the temperature/pressure relief valve.
• mini-Compact Series: P/N 03.02.020.00
• Compact and Imperial Series: P/N 03.02.022.00
Temperature/Pressure Relief Valve
CAUTION
BURN HAzARD: valves supplied by Hatco are designed
for high temperature commercial operation. Do not
substitute Hatco valves with valves designed for domestic
water heaters.
Do not use an anti-siphon or check valves on incoming
water line.
Form No. EBOOSTERm-0712
19
INSTALLATION
Plumbing Connections
Pressure Reducing Valve
with High Pressure By-pass
(20 psi [138 kPa] flow
pressure maximum)
Back
Pressure
Relief Valve†
Temperature/
Pressure Gauge
3/4” Gate or
Ball Valve‡
Temperature/Pressure
Relief Valve, 150 PSI/210°F
(1040 kPa/99°C)
Discharge from T/P Valve.
Air gap must comply
with plumbing code.
Outlet
3/4”
Union‡
Inlet
Water Inlet from
primary water
heater
Temperature/
Pressure Gauge
Outlet to
Dishwasher
Blended Phosphate Water
Treatment System†
NOTE: Centerline of booster “T” fitting must
not extend closer than 102 mm (4″) to the floor.
Drain
Valve‡
Floor
Drain‡
Shock Absorber
for water hammer†
Imperial “S” Series
Pressure Reducing Valve
with High Pressure By-pass
(20 psi [138 kPa] flow
pressure maximum)
Temperature/
Pressure Gauge
Back
Pressure
Relief Valve†
3/4” Gate or
Ball Valve‡
Temperature/Pressure
Relief Valve, 150 PSI/210°F
(1040 kPa/99°C)
3/4”
Union‡
Discharge from T/P Valve.
Air gap must comply
with plumbing code.
Outlet
Outlet
Inlet
Inlet
Temperature/
Pressure Gauge
Outlet to
Dishwasher
Water Inlet from
primary water heater
Blended Phosphate Water
Treatment System†
Drain Valve‡
Floor Drain‡
Shock Absorber
for water hammer†
NOTE: Centerline of booster “T” fitting must
not extend closer than 102 mm (4″) to the floor.
Two Imperial models Connected in Series
† Not supplied, but is available as an option/accessory.
‡ Not supplied with booster heater.
WARNING
valves, gauges, and unions must be installed per diagram
to ensure proper operation, servicing, and warranty
coverage.
20
Form No. EBOOSTERm-0712
INSTALLATION
Plumbing Connections
Pressure Reducing Valve
with High Pressure By-pass
(20 psi [138 kPa] flow
pressure maximum)
Back
Pressure
Relief Valve†
Temperature/
Pressure Gauge
Temperature/Pressure
Relief Valve, 150 PSI/210°F
(1040 kPa/99°C)
Temperature/
Pressure Gauge
Outlet
Outlet to
Dishwasher
3/4” Gate or
Ball Valve‡
Water Inlet from
primary water
heater
Shock Absorber
for water hammer†
Drain Valve‡
Blended Phosphate Water
Treatment System†
Inlet
Discharge from T/P Valve.
Air gap must comply
with plumbing code.
Floor Drain‡
Compact Series
Pressure Reducing Valve
with High Pressure By-pass
(20 psi [138 kPa] flow
pressure maximum)
Temperature/
Pressure Gauge
Temperature/
Pressure Gauge
Shock Absorber
for water hammer†
Back
Pressure
Relief Valve†
3/4” Gate or
Ball Valve‡
Outlet to
Dishwasher
Temperature/Pressure
Relief Valve, 150 PSI/210°F
(1040 kPa/99°C)
Inlet
Water Inlet from
primary water
heater
Discharge from T/P Valve.
Air gap must comply
with plumbing code.
Blended Phosphate Water
Treatment System†
Flow
Restrictor†
Floor Drain‡
NOTE: Centerline of booster “T” fitting must
not extend closer than 102 mm (4″) to the floor.
mini-Compact models
† Not supplied, but is available as an option/accessory.
‡ Not supplied with booster heater.
WARNING
valves, gauges, and unions must be installed per diagram
to ensure proper operation, servicing, and warranty
coverage.
Form No. EBOOSTERm-0712
21
Drain Valve‡
INSTALLATION
Outlet
1. Flush the water supply line to remove any pipe compound
and foreign matter.
Temperature/
pressure gauge
with 1/2”
pipe thread
2. Connect the booster heater water outlet to the commercial
dish machine sanitizing rinse pipe connection using a 3/4"
union and piping.
NOTICE
DO NOT turn or adjust water outlet connection on Large
Compact Series units (C-24 to C-57).
1/2” copper
female fitting
adapter
NOTE: Red mark on water outlet pipe for C-24 to C-57 series
units must remain in the top most position.
3/4” nominal
copper pipe
NOTE: Be certain the connection is made to the final rinse and
not to the wash tank.
3. Install a temperature/pressure gauge in the outlet line. The
temperature sensing element must be in the water stream
and the gauge must be mounted upright.
Temperature
sensing element
Recommended Temperature/Pressure Gauge Installation
• Water temperature at the outlet should be 185°–190°F
(85°–88°C).
NOTE: Some dish machines require two booster heaters to be
plumbed in series (not parallel) to meet the demand.
To ensure proper operation, a 30°F (-1°C) temperature
differential must be maintained between the outlet of
the first booster heater and the inlet of the second
booster heater.
Temperature/
pressure gauge
with 1/2”
pipe thread
Center bottom
of sensor
in copper pipe
1/2” copper
female fitting
adapter
3/4" nominal
copper pipe
NOTE: Hatco recommends installing an optional shock
absorber (P/N 03.04.057.00) in the outlet line as close
as possible to the commercial dish machine solenoid
rinse valve. The shock absorber softens the water
hammer caused by automatic dish machine valves.
3/4" x 1/2" x 3/4"
copper tee
Plumbing Installation Inspection
1. Close the drain valve and fill the booster heater with water.
Temperature
sensing element
alternate Temperature/Pressure Gauge Installation
2. Check all pipe connections for leaks.
3. make sure the temperature/pressure relief valve discharge
is not blocked.
WARNING
Hatco has always endorsed the use of safety equipment
when using a booster water heater or storage-type water
heater. Hatco booster heaters are shipped with a
temperature/pressure relief valve at no extra charge. This
valve must be installed into the marked opening provided
in the tank. valves supplied by Hatco are designed for
high temperature commercial operation. Do not substitute
Hatco supplied valves with valves designed for domestic
operation.
4. Vent air from the tank before operating by opening the
temperature/pressure relief valve.
CAUTION
DO NOT turn on power to the booster heater until tank has
been filled with water and all air has been vented through
the dish machine rinse nozzle. The heating elements will
burn out in seconds if operated when they are not
immersed in water.
It is essential to recognize that even though a water heater
may be properly installed initially and approved, there
always exists the possibility that unknowing individuals
might alter or change the installation in a manner that
would render it unsafe. Therefore, it is important that all
safety programs provide some mechanism to assure that
these installations are inspected periodically.
22
Form No. EBOOSTERm-0712
Electrical — All Sizes and voltages
Electrical Connections
INSTALLATION
1. Remove the front jacket cover screws, pull the cover
forward and remove the cover.
General
Hatco Electric Booster Water Heaters are available for operation
on standard power systems. Check the specification label for
the proper power supply.
NOTE: On Imperial models, there is a hinged access panel
under the front jacket cover. Remove the bottom screw
and lift the panel up to expose the fuse blocks.
all internal electrical connections have been made at the
factory. See the “Circuit Breaker and Fused Disconnect Switch”
chart in the SPECIFICaTIONS section for supply wire size, fuse,
breaker, and conduit recommendations. Consult local codes for
verification and compliance.
• On mini-Compact models, remove front cover screws.
Ease cover forward and upward.
• On Compact models, the control box is under the front
hinged jacket cover.
2. Locate the heater terminal or fuse block(s) inside the unit.
WARNING
ELECTRIC SHOCK HAzARD:
• Unit must be installed by qualified, trained installers.
Installation must conform to all local electrical and
plumbing codes. Installation by unqualified personnel
will void the unit warranty and may lead to electric
shock or burn, as well as damage to unit and/or its
surroundings. Check with local plumbing and electrical
inspectors for proper procedures and codes.
NOTE: See “Circuit Breaker and Fused Disconnect Switch”
chart in the SPECIFICaTIONS section for proper
connections and wire size.
NOTE: Only 6, 7, and 9 kW models, in 208 or 240 volt, can be
converted to single or three phase in the field. Refer to
the wiring diagram for proper wiring connections at the
terminal block.
3. Bring power leads from a properly sized disconnect switch
or circuit breaker through the knockout provided on the
unit. Connect leads to the terminal or fuse block(s).
USE COPPER WIRE ONLy. TIGHTEN CONNECTIONS
PROPERLy TO A MINIMUM OF 40 INCH POUNDS.
• Turn OFF power at fused disconnect switch/circuit
breaker and allow unit to cool before performing any
cleaning, adjustments, or maintenance.
• Consult a licensed electrical contractor for proper
electrical installation conforming to local electrical
codes and the National Electrical Code (N.E.C.).
NOTE: Due to the rigors of transportation all connections
should be checked for tightness before heater is put
into operation.
4. Properly connect an equipment grounding connector to the
grounding lug (located near the supply terminals).
NOTICE
Units are voltage-specific. Refer to specification label for
electrical requirements before beginning installation.
Connecting unit to incorrect power supply will void
product warranty and may damage unit.
CAUTION
DO NOT turn on power to the booster heater until tank has
been filled with water and all air has been vented through
the dish machine rinse nozzles. Heating elements will
burn out in seconds if operated when not immersed in
water.
5. Replace and secure cover(s).
Imperial Series
Electrical
Knockout
Compact Series
Electrical
Knockout
Electrical
Knockouts
Electrical Knockout Locations
Form No. EBOOSTERm-0712
Mini-Compact Series
23
OPERATION
General
Use the following procedures to operate Hatco Electric Booster
Water Heaters.
Power ON/OFF
Switch
CAUTION
BURN HAzARD: Water in unit is very hot. Wear protective
gloves and proper attire when operating to avoid injury.
Startup
1. Close the drain valve.
2. Open the shutoff valve to the primary water supply line. The
water temperature at inlet should be 110° to 140°F (43° to
60°C) and should not exceed 160°F (71°C).
Indicator Light
Control Panel (Imperial and Compact models shown)
Shutdown
NOTE: Minimum temperature differential between inlet and
outlet should never be less than 30°F (-1°C).
Under normal and regular operation, Hatco recommends that
the unit be turned on at all times.
3. Vent all the air from the tank through the dish machine rinse
nozzles and the temperature/pressure relief valve when the
tank is filled with water.
If the booster heater will not be used for an extended period of
time or will be exposed to freezing conditions it should be
drained to prevent damage to the unit.
1. move the Power ON/OFF (I/O) switch to the OFF (O)
position, and turn off power at the fused disconnect
switch/circuit breaker.
CAUTION
DO NOT turn on power to the booster heater until tank has
been filled with water and all air has been vented through
the dish machine rinse nozzles. Heating elements will
burn out in seconds if operated when not immersed in
water.
2. Close the shutoff valve to the primary water supply line.
3. Open the drain valve and drain the water from the booster
heater tank.
4. Check all plumbing connections for leaks.
5. Check the temperature/pressure relief valve discharge
opening to be sure it is not blocked and no scale or other
foreign matter has reduced the size of the opening.
NOTICE
Always drain booster heater with power to the unit off or
element burnout could occur.
6. Turn on the booster water heater.
• For Imperial and Compact models, move the Power
ON/OFF (I/O) switch on the control panel to the ON (I)
position.
• For mini-Compact models, turn on power at the fused
disconnect switch/circuit breaker.
NOTE: Mini-Compact models can be configured with an
optional Power ON/OFF (I/O) switch.
7. When the booster water heater has had sufficient heating
time, operate the rinse cycle and check the water
temperature and pressure readings on the gauges.
• Water temperature at the booster outlet should be
185°–190°F (85°–88°C) and flow pressure should be 20
psi (138 kPa) maximum.
NOTE: Outlet water temperatures can be adjusted for
Low-Temperature Dish Machine applications. See the
maINTENaNCE section for thermostat adjustment
procedure.
WARNING
Units are equipped with a high temperature limit safety
switch that will shut off the power if the unit overheats.
Contact an Authorized Hatco Service Agent if the high
temperature limit safety switch cannot be reset or
continues to trip.
24
Form No. EBOOSTERm-0712
MAINTENANCE
General
High Temperature Limit Safety Switch
Electric Booster Water Heaters are designed for maximum
durability and performance with minimum maintenance.
all Hatco Electric Booster Water Heaters are equipped with a
manually reset high temperature limit safety switch. If the
temperature of the water in the heater exceeds 210°F (99°C)
the safety switch will shut off the power. The switch must be
manually reset.
WARNING
ELECTRIC SHOCK HAzARD:
• Turn OFF power at fused disconnect switch/circuit
breaker and allow unit to cool before performing any
cleaning, adjustments, or maintenance.
If the high temperature limit safety switch needs to be reset use
the following procedure:
1. move the Power ON/OFF (I/O) switch to the OFF (O)
position and unplug the unit from the power source.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
2. Remove the access cover.
3. Push the red reset button.
• Do not steam clean or use excessive water on unit.
4. If tripping repeats, call an authorized Service agent.
• Do not clean unit when it is energized or hot.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
Front View of
Thermostat
Adjustment Screws
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
Inner
Screw
Outer
Screw
Thermostat
Adjustment
Screw
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.
Thermostat Adjustment
The thermostat is factory calibrated at 185°–190°F (85°–88°C).
If adjustment or recalibration is required due to the rigors of
transportation, use the following procedure.
Access Cover
Thermostat adjustment and High Temperature Limit Safety Switch
NOTE: Low temperature dish machines require the thermostat(s)
to be adjusted to 140°–150°F (60°–66°C).
1. move the Power ON/OFF (I/O) switch to the OFF (O)
position and unplug the unit from the power source.
2. Remove the access cover.
3. adjust the temperature setpoint to the desired temperature.
• To lower the temperature setpoint, turn the outer screw
counterclockwise.
• To raise the temperature setpoint, turn the outer screw
clockwise.
NOTE: 1/6 turn of the outer screw equals 12°F (6.7°C).
NOTE: If recalibration is necessary, with the outer screw at
high stop, turn the inner screw clockwise to raise the
set point.
NOTE: 1/6 turn of the inner screw equals 8°F (4.4°C).
Form No. EBOOSTERm-0712
High Limit Switch
Reset Button
25
OPTIONS AND ACCESSORIES
Blended Phosphate Water Treatment System
Stainless Steel Adjustable Legs
The optional Blended Phosphate Water Treatment System
(P/N 03.05.061.00) dispenses a small amount of polyphosphate
into the water. The polyphosphate prevents the buildup of
mineral molecules.
Stainless steel adjustable legs (P/N 05.30.070.00) are available
as accessories for all models.
Use the following procedure to install legs:
1. Carefully place unit on its side.
The optional blended phosphate water treatment system is
installed with unions on the incoming 3/4" water supply line after
the pressure reducing valve and before the booster heater.
NOTICE
Replacing a Phosphate Cartridge
(P/N 03.05.061A.00)
Do not lay unit on the side with the control panel. Damage
to the unit could occur.
Cartridges supplied have a usage rating of 100,000 gallons
(378,541 liters) of water. To ensure proper operation, the
cartridges must be replaced when the compound is near the
bottom of the cartridge.
2. Thread the adjustable legs into the existing leg holes on
the bottom of the unit.
3. after all legs are secure, return the unit to the upright
position.
Use the following procedure for replacement:
1. move the ON/OFF (I/O) switch to the OFF (O) position.
NOTE: If unit is not level, use an adjustable wrench to adjust
the foot of each leg until unit is level. Each leg is
adjustable from 6" (152 mm) to 7" (178 mm).
2. Shut off water supply and open the drain valve to remove
water in piping.
3. Loosen the canister using the attached wrench.
Adjustable
Foot
4. Remove canister and discard depleted cartridge.
5. Using a clean damp cloth, wipe the interior of the canister
clean.
NOTE: Make sure the O-ring seal is placed properly in the
canister.
6. Reverse the above procedure to reinstall.
Stainless Steel adjustable Legs
Floor Mounting Legs
NOTE: Product failure caused by liming or sediment buildup is
not covered under warranty.
Stainless steel adjustable legs with deck mounting flanges
secure the booster heater to the floor are available options for
Compact and Imperial models only.
Mounting Slide Brackets
a set of optional mounting slide brackets is available for
Compact models only. (P/N R04.20.030.00)
Plumbing Accessories
a shock absorber, a brass pressure reducing valve, and a back
pressure relief valve are available as accessories.
Canister
Wrench
Shock Absorber
(P/N 03.40.057.00)
Blended Phosphate Water Treatment System
Stainless Body and Base
an optional stainless body and base is available for all models.
Brass Pressure
Reducing Valve
(P/N 03.02.015.00)
Security Package
a security package is a factory-installed option for Compact and
Imperial models only. a security package contains Torx® screws
and a control cover.
Back Pressure
Relief Valve*
(P/N 03.02.039.00)
*Not available for Mini-Compact models.
Plumbing accessories
26
Form No. EBOOSTERm-0712
TROUBLESHOOTING GUIDE
IMPORTANT! Read Before Using the
Troubleshooting Guide
Electrical Connections
• Booster heater voltage must be correct for voltage
available. Check the specification label on the booster
heater for full information.
many times when a booster heater does not appear to be
functioning properly, the fault is not with the booster heater itself
but with factors outside the heater.
• The breakers or fuses mUST be properly sized.
Plumbing Connections
• The temperature/pressure relief valve must be properly
installed and be supplied by Hatco.
WARNING
ELECTRIC SHOCK HAzARD:
• Turn OFF power at fused disconnect switch/circuit
breaker and allow unit to cool before performing any
cleaning, adjustments, or maintenance.
• a check valve should not be installed ahead of the booster.
NOTE: If a check valve is installed and cannot be removed,
install a back pressure relief valve (P/N 03.02.039.00) set
at 125 psi (862 kPa) on the incoming line between the
pressure reducing valve and the inlet to the booster
heater. Discharge must be to open site drain.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
Before proceeding with the “Troubleshooting Guide” to diagnose
an issue, check aLL of the following outside factors.
If the unit does not function properly after performing these
checks, continue to the “Troubleshooting Guide” in this section.
Water Temperature
• Check the temperature of the water feeding into the
booster tank. It must be 110° to 140°F (43° to 60°C),
depending on the heating capability of the unit. The inlet
water supply must be of sufficient quantity to hold its
temperature throughout the dishwashing operation.
• If the wash tank of the dish machine is filled through the
booster heater, this will use up all of the 180°F (82°C) water
in storage. Sufficient time must be allowed to reheat the
water in storage before starting the dish machine.
• Primary water heater temperature should not exceed 160°F
(71°C).
Water Pressure
• Water pressure at the inlet to the booster heater must be
adequate for proper operation of the rinse cycle of the dish
machine, not to exceed 20 psi (138 kPa). Check with dish
machine manufacture for specific details.
• If incoming water exceeds 20 psi (138 kPa), a pressure
reducing valve must be installed.
Form No. EBOOSTERm-0712
27
TROUBLESHOOTING GUIDE
WARNING
WARNING
This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
Symptom
Water reaches 180°F (82°C) but
does not last through the entire
dish machine operation.
ELECTRIC SHOCK HAzARD: Turn OFF power at fused
disconnect switch/circuit breaker and allow unit to cool
before performing any cleaning, adjustments, or
maintenance.
Probable Cause
Low incoming water temperature.
Incoming water temperature drops.
Flow pressure is too high.
Booster heater may be undersized.
Incorrect voltage.
Corrective Action
Incoming water temperature must be
adequate for booster size. Increase incoming
water temperature.
Primary water supply is not adequate to
provide correct temperature in sufficient
quantities. Increase supply of primary hot
water.
Higher pressure uses an excessive quantity of
hot water. adjust flow pressure to 20 psi (138
kPa).
Booster heater must be properly sized for
incoming water temperature and rinse
requirements of the dish machine.
Check voltage on heater serial plate and make
sure supplied voltage matches. a 240V
booster heater operating on 208V reduces
wattage to 76% efficiency.
The booster heater does not Unit may have been energized without Replace the element(s).
heat at all or only delivers water water (dry fired) causing the element(s) to
at 120°- 150°F (49°-66°C).
burn out quickly.
Fuses may be blown or circuit breaker
tripped.
Check for proper fuse sizing. Replace fuses.
Check/reset circuit breaker.
Temperature setting out of calibration or
inoperable.
Temperature setting should be maximum of
190°F (88°C).
Over-current fuses may be blown.
Contactors do not pull in.
High limit switch may be tripped or
defective.
Transformer not working properly.
Low water cutoff inoperable, contacts do
not close.
Check for shorted elements, bad fuse block or
short in wiring.
Test for voltage at coils. If coils are open or
shorted, replace contactors.
Reset switch, refer to “High Temperature Limit
Safety Switch” in the maINTENaNCE section.
If switch continues to trip or cannot be reset
contact an authorized Service agent.
Check secondary voltage, it should be the
same as the control circuit voltage. If not,
replace the transformer.
Remove probe wire and touch it to the tank. If
contacts close, probe is fouled and must be
cleaned or replaced.
Relay on circuit board maybe defective.
Jumper terminals 6 and 7. If unit energizes,
circuit board is defective and should be
replaced.
28
Form No. EBOOSTERm-0712
Symptom
Probable Cause
TROUBLESHOOTING GUIDE
Corrective Action
Water at dish machine is not at Gauge(s) not working properly.
the proper temperature.
Check temperature of water with a
thermometer to be certain gauges are working
correctly. If not, replace gauge(s).
Thermostat set too low.
Heating element(s) burn out.
adjust or recalibrate, refer to “Thermostat
adjustment” in the maINTENaNCE section. If
thermostat will not recalibrate properly,
replace it.
Booster heater has more than (5) linear feet If located farther than 5 linear feet (1524 mm),
(1524 mm) of water pipe to the dish pipes should be wrapped in insulation, and/or
machine, causing the water to cool off a recirculating system installed.
inside the pipe.
Tank inadvertently drained
element(s) in a dry condition.
leaving
Lime buildup in tank causing element(s) to
split and burn out.
Relief valve dribbles.
No pressure reducing valve installed or
incorrect valve installed causing pressure
build-up inside booster tank.
Bypass in pressure reducing valve may be
blocked.
Check valve or anti-siphon valve installed in
the feed line.
Relief valve opens.
High temperature limit safety
switch trips.
Chattering contactor or low
water cutoff circuit board
Unit is overheating.
Contactor may be sticking in closed
position not allowing unit to cycle off.
Replace element(s), and clean or delime tanks
periodically. a water softener or blended
phosphate treatment system may be required.
a pressure reducing valve with high pressure
bypass must be installed in the incoming water
line to allow water to expand back into the
feed line.
Clean bypass or replace with new valve with
built in bypass.
Remove check valve or anti-siphon valve to
allow for water expansion or install a back
pressure relief valve (P/N 03.02.039.00) on
the incoming water line.
Thermostat may be set too high or is sticking.
Recalibrate or replace the thermostat.
Replace contactor(s).
Temperature limit safety switch is defective. If booster heater is not overheating, replace
High Limit Safety Switch.
Thermostat set too high.
Incoming water temperature too high
causing nuisance tripping of high
temperature limit switch.
adjust or recalibrate, refer to “Thermostat
adjustment” in the maINTENaNCE section.
Incoming water temperature should not be
higher than 160°F (71°C).
Loose connections or wire connection has
insulation under crimp.
Tighten all connections and check crimps
Probe may be fouled.
Bypass probe by removing wire from low
water cutoff probe and grounding to tank.
Clean or replace probe if chattering stops.
Low voltage.
Contactor(s) may be bad.
Form No. EBOOSTERm-0712
Replace element(s), and make sure tank is full
of water at all times. Check low water cut-off
system for proper operation.
Check control circuit voltage or secondary
voltage with transformer.
Test contactor coils and replace if needed.
29
LIMITED WARRANTy
1. PRODUCT WARRANTy
Hatco warrants the products that it manufactures (the
“Products”) to be free from defects in materials and
workmanship, under normal use and service, for a period of one
(1) year from the date of purchase when installed and
maintained in accordance with Hatco’s written instructions or
18 months from the date of shipment from Hatco. Buyer must
establish the Product’s purchase date by registering the Product
with Hatco or by other means satisfactory to Hatco in its sole
discretion.
THE FOREGOING WaRRaNTIES aRE EXCLUSIVE aND IN
LIEU OF aNY OTHER WaRRaNTY, EXPRESSED OR
ImPLIED, INCLUDING BUT NOT LImITED TO aNY ImPLIED
WaRRaNTY OF mERCHaNTaBILITY OR FITNESS FOR a
PaRTICULaR PURPOSE OR PaTENT OR OTHER
INTELLECTUaL PROPERTY RIGHT INFRINGEmENT.
Without limiting the generality of the foregoing, SUCH
WaRRaNTIES DO NOT COVER: Coated incandescent light
bulbs, fluorescent lights, heat lamp bulbs, coated halogen light
bulbs, halogen heat lamp bulbs, xenon light bulbs, LED light
tubes, glass components, and fuses; Product failure in booster
tank, fin tube heat exchanger, or other water heating equipment
caused by liming, sediment buildup, chemical attack, or
freezing; or Product misuse, tampering or misapplication,
improper installation, or application of improper voltage.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) year Parts and Labor PLUS One (1) Additional
year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HWB Series (metal sheathed)
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will be
limited solely, at Hatco’s option, to repair or replacement using
new or refurbished parts or Product by Hatco or a Hatcoauthorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves
the right to accept or reject any such claim in whole or in part.
In the context of this Limited Warranty, “refurbished” means a
part or Product that has been returned to its original
specifications by Hatco or a Hatco-authorized service agency.
Hatco will not accept the return of any Product without prior
written approval from Hatco, and all such approved returns shall
be made at Buyer’s sole expense. HaTCO WILL NOT BE
LIaBLE,
UNDER
aNY
CIRCUmSTaNCES,
FOR
CONSEQUENTIaL OR INCIDENTaL DamaGES, INCLUDING
BUT NOT LImITED TO LaBOR COSTS OR LOST PROFITS
RESULTING FROm THE USE OF OR INaBILITY TO USE THE
PRODUCTS OR FROm THE PRODUCTS BEING
INCORPORaTED IN OR BECOmING a COmPONENT OF
aNY OTHER PRODUCT OR GOODS.
b) One (1) year Parts and Labor PLUS Four (4) years
Parts-Only Warranty:
3CS and FR Tanks
c) One (1) year Parts and Labor PLUS Nine (9) years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
d) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
30
Form No. EBOOSTERm-0712
NOTES
Form No. EBOOSTERm-0712
31
HATCO AUTHORIzED PARTS DISTRIBUTORS
ALABAMA
Jones mcLeod appl. Svc.
Birmingham
205-251-0159
IOWA
Electric motor Service Co.
Davenport
319-323-1823
NEW yORK
acme american Repairs, Inc.
Brooklyn
718-456-6544
TExAS
GCS Service
Fort Worth
Byassee Equipment Co.
Phoenix
602-252-0402
KENTUCKy
Service Solutions Group
Lexington
859-254-8854
appliance Installation
Buffalo
Cooking Equipment Specialist
mesquite
888-866-9276
ARIzONA
Service Solutions Group
Phoenix
602-234-2443
CALIFORNIA
Industrial Electric
Commercial Parts & Service, Inc.
Huntington Beach
714-379-7100
Chapman appl. Service
San Diego
619-298-7106
P & D appliance
Commercial Parts & Service, Inc.
S. San Francisco
650-635-1900
COLORADO
Hawkins Commercial appliance
Englewood
303-781-5548
FLORIDA
Whaley Foodservice Repair
Jacksonville
904-725-7800
Goodwin Tucker Group
Des moines
515-262-9308
Service Solutions Group
Louisville
502-451-5411
LOUISIANA
Chandlers Parts & Service
Baton Rouge
225-272-6620
MARyLAND
Electric motor Service
Baltimore
410-467-8080
GCS Service
Silver Spring
301-585-7550
MASSACHUSETTS
ace Service Co., Inc.
Needham
781-449-4220
3Wire Nass Service Co., Inc.
Orlando
407-425-2681
MICHIGAN
Bildons appliance Service
Detroit
248-478-3320
Comm. appliance Service
Tampa
813-663-0313
midwest Food Equip. Service
Grandville
616-261-2000
B.G.S.I.
Pompano Beach
GEORGIA
TWC Services
mableton
954-971-0456
Commercial Kitchen Service
Bay City
517-893-4561
770-438-9797
MINNESOTA
GCS Service
Plymouth
Heritage Service Group
Norcross
866-388-9837
Southeastern Rest. Svc.
Norcross
770-446-6177
HAWAII
Burney’s Comm. Service, Inc.
Honolulu
808-848-1466
Food Equip Parts & Service
Honolulu
808-847-4871
ILLINOIS
Parts Town
Lombard
708-865-7278
Eichenauer Elec. Service
Decatur
217-429-4229
midwest Elec. appl. Service
Elmhurst
630-279-8000
Cone’s Repair Service
moline
309-797-5323
INDIANA
GCS Service
Indianapolis
317-545-9655
MISSOURI
General Parts
Kansas City
800-345-4221
816-421-5400
Commercial Kitchen Services
St. Louis
314-890-0700
Kaemmerlen Parts & Service
St. Louis
314-535-2222
NEBRASKA
anderson Electric
Omaha
402-341-1414
NEvADA
Burney’s Commercial
Las Vegas
702-736-0006
Hi. Tech Commercial Service
N. Las Vegas
702-649-4616
NEW JERSEy
Jay Hill Repair
Fairfield
Service Plus
Flanders
973-575-9145
973-691-6300
alpro Service Co.
Brooklyn
Printed in U.S.a. July 2012
716-884-7425
Duffy’s Equipment Services, Inc.
Buffalo
800-836-1014
3Wire Northern
Plattsburgh
800-634-5005
J.B. Brady, Inc.
Syracuse
315-422-9271
Duffy’s Equipment Services, Inc.
Sauquoit
800-836-1014
NORTH CAROLINA
authorized appliance
Charlotte
704-377-4501
OHIO
akron/Canton Comm. Svc. Inc.
akron
330-753-6635
Service Solutions Group
Cincinnati
513-772-6600
Commercial Parts and Service
Columbus
614-221-0057
Electrical appl. Repair Service
Brooklyn Heights
216-459-8700
E. a. Wichman Co.
Toledo
419-385-9121
OKLAHOMA
Hagar Rest. Service, Inc.
Oklahoma City
405-235-2184
Krueger, Inc.
Oklahoma City
OREGON
Ron’s Service, Inc.
Portland
405-528-8883
503-624-0890
PENNSyLvANIA
Elmer Schultz Services
Philadelphia
215-627-5401
FaST Comm. appl. Service
Philadelphia
215-288-4800
appliance Installation & Service
Pittsburgh
412-809-0244
K & D Service Co.
Harrisburg
Electric Repair Co.
Reading
RHODE ISLAND
marshall Electric Co.
Providence
717-236-9039
610-376-5444
401-331-1163
SOUTH CAROLINA
Whaley Foodservice Repair
W. Columbia
803-791-4420
TENNESSEE
Camp Electric
memphis
HATCO CORPORATION
P.O. Box 340500
Milwaukee, WI 53234-0500 U.S.A.
(800) 558-0607 (414) 671-6350
Parts and Service Fax (800) 690-2966
International Fax (414) 671-3976
partsandservice@hatcocorp.com
www.hatcocorp.com
718-386-2515
901-527-7543
800-433-1804
armstrong Repair Service
Houston
713-666-7100
Refrigerated Specialist, Inc.
mesquite
888-866-9276
Commercial Kitchen Repair Co.
San antonio
210-735-2811
UTAH
La monica’s Rest. Equip. Service
murray
801-263-3221
vIRGINIA
Daubers
Norfolk
757-855-4097
Daubers
Springfield
703-866-3600
WASHINGTON
3Wire Restaurant appliance
Seattle
800-207-3146
WISCONSIN
a.S.C., Inc.
madison
608-246-3160
a.S.C., Inc.
milwaukee
414-543-6460
CANADA
ALBERTA
Key Food Equipment Service
Edmonton
780-438-1690
BRITISH COLUMBIA
Key Food Equipment Service
Vancouver
604-433-4484
Key Food Equipment Service
Victoria
250-920-4888
MANITOBA
air Rite, Inc.
Winnipeg
NEW BRUNSWICK
EmR Services, Ltd.
moncton
ONTARIO
R.G. Henderson Ltd.
Toronto
204-895-2300
506-855-4228
416-422-5580
Choquette - CKS, Inc.
Ottawa
613-739-8458
QUÉBEC
Choquette - CKS, Inc.
montreal
514-722-2000
Choquette - CKS, Inc.
Québec City
418-681-3944
UNITED KINGDOM
marren Group
Northants
+44(0)1933 666233
Register your unit online!
See ImPORTaNT OWNER INFORmaTION
section for details.
P/N 07.04.111.00 Form No. EBOOSTERm-0712
Download PDF