Venturer | PVS7980 | Owner`s manual | Venturer PVS7980 Owner`s manual

DUAL SCREEN MOBILE DVD
PVS7980
NEED MORE HELP?
DO NOT RETURN THIS
PRODUCT TO THE STORE
OWNER’S MANUAL
Please visit online help at
http://www.venturer.com
Safety Precautions
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE. DO NOT PLACE OBJECTS FILLED
WITH LIQUIDS ON OR NEAR THIS UNIT.
CAUTION
CAUTION:
• Use of controls, adjustments or
performance of procedures other
than those specified may result in
hazardous radiation exposure.
• DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE.
INVISIBLE LASER RADIATION WHEN
OPEN.
AVOID EXPOSURE TO BEAM.
This product contains a
low power laser device.
CLASS 1 LASER PRODUCT
Placement INFORMATION
• Do not use this unit in places that are extremely hot, cold, dusty, or humid.
• Do not restrict the airflow of this unit by placing it somewhere with poor airflow, by covering
it with a cloth, or by placing it on bedding or carpeting.
Safety INFORMATION
• When connecting or disconnecting the Car power adapter, grip the power and not the cord
itself. Pulling the cord may damage it and create a hazard.
E-1
811-798191W012.indd 1
4/1/2008 5:00:56 PM
• When you are not going to use the unit for a long period of time, disconnect the Car power
adapter.
Condensation INFORMATION
When left in a heated room where it is warm and damp, water droplets or condensation may form
inside the unit. When there is condensation inside the unit, the unit may not function normally.
Let the unit stand for 1-2 hours before turning the power on or gradually heat the room and
allow the unit to dry before use.
FCC Information
WARNING: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment, when used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an AC power outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Should any problems occur, disconnect the Car power adapter and refer
servicing to a qualified technician.
IMPORTANT SAFETY PRECAUTIONS
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type power. A
polarized power has two blades with
one wider than the other. A grounding
type power has two blades and a third
grounding prong. The wide blade or
the third prong is provided for your
safety. When the provided power cord
does not fit into your AC power outlet,
consult an electrician for replacement
of the obsolete outlet.
10.Protect the AC power cord from being
E-2
811-798191W012.indd 2
walked on or pinched particularly at
the power, convenience receptacles,
and the point where they exit from
the apparatus.
11.Only use attachments/accessories
specified by the
manufacturer.
12.Use only with the cart,
stand, tripod, bracket, or
table specified by the manufacturer, or
sold with the apparatus. When a cart
is used, use caution when moving the
cart/apparatus combination to avoid
injury from tip-over.
13.Unplug this apparatus during lightning
storms or when unused for long
periods of time.
14.Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in
any way, such as the AC power cord is
damaged, liquid has spilled or objects
have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally,
or has been dropped.
4/1/2008 5:00:57 PM
TABLE OF CONTENTS
SAFETY PRECAUTIONS .............. 1 - 2
IMPORTANT SAFETY INSTRUCTIONS .
.......................................................... 2
TABLE OF CONTENTS ...................... 3
DISC FORMATS ................................ 4
MAINTENANCE ............................... 5
ACCESSORIES .................................. 5
GETTING STARTED .......................... 5
REMOTE CONTROL REFERENCE GUIDE
.......................................................... 6
UNIT AND MONITOR REFERENCE
GUIDE .............................................. 7
power supply ............................... 8
CONNECTIONS ........................ 9 - 11
Watching a DVD on the Main Unit
and the Monitor ........................... 9
Watching a TV on Main Unit ........ 9
Listening to a Stereo Receiver or an
Amplifier on the Main Unit ........ 10
P l ay i n g G a m e S y s t e m / Vi d e o
Equipment on the Monitor ......... 10
Using the Monitor with Other
Equipment while Playing DVDs on the
Main Unit ................................ 11
Using Headphones/Earphones .... 11
PLACEMENT .............................. 12-13
Mounting in the Vehicle ............. 12
Using the Stand .......................... 13
SOUND SYSTEM ............................ 13
CD/DVD OPERATION ................... 14
Playing a Disc ............................ 14
Playing a Picture File Disc .......... 14
Angle Selection (DVD) ............... 14
SPECIAL FUNCTIONS .................... 15
Display Function (DVD) ............. 15
Locating a Specific Title (DVD) ... 15
.Locating a Specific Chapter/Track ......
................................................... 15
Locating a Specific Time ............. 15
REPEAT PLAYBACK ......................... 16
Repeating a Chapter/Title (DVD) ........
................................................... 16
Repeating a Single Track/an Entire
Disc (CD) ................................... 16
.Repeating a Specific Section (DVD/
CD) ............................................ 16
DVD PROGRAMMABLE PLAYBACK ......
........................................................ 17
Programmable Memory .............. 17
Title/Chapter Programmed Playback
(DVD) ..................................... 17
CUSTOMIZING THE DVD FUNCTION
SETTINGS ................................. 17-18
Language Setup .......................... 17
Video Setup ............................... 18
System Setup .............................. 18
TROUBLE SHOOTING GUIDE ...... 19
LIMITED WARRANTY ............... BACK
E-3
811-798191W012.indd 3
4/1/2008 5:00:57 PM
DISC FORMATS
This unit can playback:
DVDs
[8cm/12cm disc]
CD-R/CD-RW
audio cds
[8cm/12cm disc]
Compatible
Region Management Information
Region Management Information: This unit is designed and manufactured to respond to the Region
Management Information that is encoded on DVDs. If the region number printed on the DVD does not
correspond to the region number of this unit, this unit cannot play that disc.
The region number of this unit is
.
Disc Function or Operation that is Not Available
When the
symbol appears on the screen, it indicates that the function or operation attempted is not
available at that time. This occurs because the DVD manufacturer determines the specific functions.
Certain functions may not be available on some discs. Be sure to read the documentation provided
with the DVD.
Icons Used on DVDs
Language selections for audio
Sample lcons
Language selections for subtitles
Note:
• When playing back a CD-G (Graphics)
or CD EXTRA disc, the audio portion
will be played, but the graphic images
will not be shown.
Screen aspect ratio
Multiple camera angles
Region code indicator
TitleS, ChapterS and Tracks
• DVDs are divided into “titles” and “chapters”. If
the DVD has more than one movie on it, each
movie would be a separate “title”. “Chapters”
are sections of “titles”.
• Audio CDs are divided into “tracks”. A “track”
is usually one song on an Audio CD.
Note:
• Numbers identify each title, chapter, and track on
a disc. Most discs have these numbers recorded
on them, but some do not.
Notes on Unauthorized Discs:
You may not be able to play some DVDs on this unit if they were purchased from outside your geographical
area or made for business purposes.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted
material without permission.
Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132; and 5,583,936
licensed for limited viewing uses only.
This product incorporates copyright protection technology that is protected by U.S. patents and
other intellectual property rights. Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is prohibited.
E-4
811-798191W012.indd 4
4/1/2008 5:00:57 PM
MAINTENANCE
Cleaning THE Disc
heart shaped, octagonal, etc.). They may cause
malfunctions.
A defective or soiled disc inserted into the unit
can cause sound to drop out during playback.
Handle the disc by holding its inner and outer
edges.
• Do NOT touch the surface of the unlabeled
side of the disc.
• Do NOT stick paper or tape on the surface.
• Do NOT expose the disc to direct sunlight or
excessive heat.
• C l e a n t h e d i s c b e f o r e
playback. Wipe the disc
from the center outward
with a cleaning cloth.
• NEVER use solvents such as benzine or
alcohol to clean the disc.
• Do NOT use irregular shaped discs (example:
Cleaning the unit
• Be sure to turn the unit off and disconnect the AC
power cord before maintaining the unit.
• Wipe the unit with a dry soft cloth. If the surfaces
are extremely dirty, wipe clean with a cloth that
has been dipped in a weak soap-and-water
solution and wrung out thoroughly. Then wipe
with a dry cloth.
• Never use alcohol, benzene, thinner, cleaning
fluid or other chemicals. Do NOT use compressed
air to remove dust.
Important Note
Before transporting the unit, remove the disc from
the disc compartment.
Accessories
Please LOCATE the INCLUDED accessories.
To order replacement units, visit http://www.venturer.com
Remote Control (with battery) ......... x 1
Car Power Adapter .......................... x 1
DC-AV Cable .................................... x 1
Straps ................................................ x 2
GETTING STARTED
Using the Remote Control
Remove the PVC sheet
before
operating
the
Remote Control.
• Point the remote control at the REMOTE SENSOR located on the unit.
• When using this unit in bright light, the infrared
REMOTE CONTROL SENSOR may not work
properly.
• The recommended effective distance for using
the remote control is about 16 feet.
BATTERY REPLACEMENT
When the battery becomes weak, the operating
distance of the remote control will be greatly reduced
and you will need to replace the battery.
Note: • If the remote control is not going to be used for
a long time, remove the battery to avoid damage
caused by battery leakage corrosion.
• When discarding battery, environmental
problems must be considered and local rules
of laws governing the disposal of this battery
must be followed strictly.
TO CHANGE REMOTE BATTERY
1. Open the battery
door. 2.Insert one
CR2025 (3V)
size battery.
WARNING:
• Do not dispose of batteries in a fire. They may
leak and/or explode.
• The battery should not be exposed to excessive
heat such as sunshine, fire or the like.
CAUTION:
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
E-5
811-798191W012.indd 5
4/1/2008 5:00:57 PM
remote CONTROL REFERENCE GUIDE
1) VIDEO MODE Button
Press to adjust Brightness, Panel Display
or Contrast.
2)
PREV Button
Press to move back through titles,
chapters or tracks on a disc.
3)
/
SEARCH Buttons
SEARCH: Fast reverse playback.
SEARCH: Fast forward playback.
4) GOTO Button
Press to skip directly to a location on a
DVD.
5) Cursor ( , , , ) Buttons
Press to highlights selections on a menu
screen and adjust certain settings.
ENTER Button
Press to confirm selections on a menu
screen.
6) MEMORY Button
In DVD play mode, enter the number of
a selected titles or chapters.
7) Number (0 - 9) Buttons
Press to creat programs and locate a title/
chapter/track or specific time.
8) REPEAT A-B Button
Press to perform point-to-point repeat
playback on a DVD or CD.
REPEAT DISC button
Press to repeat a DVD chapter or title.
Press to repeat a CD track or the entire
disc.
SETUP Button
In STOP mode, press to enter the unit’s
SETUP menu.
9) SUBTITLE Button
Press to select one of the subtitle languages
programmed on a DVD (if available).
RETURN Button
Press to return to normal operation after
using the SETUP menu of a DVD.
10) AUDIO Button
Press to select audio soundtracks of a
DVD or change output mode of a CD.
11) ANGLE Button
Press to switch the camera angle of the
video presentation when scenes with
multiple camera angles are recorded on
a DVD.
12) DISPLAY Button
Press to show status information on the
screen.
13) STOP Button
Press to stop playing a disc.
PLAY Button
Press to start or resume playback of a
disc.
PAUSE Button
Press to pause playback and frame
advance.
NEXT Button
14)
Press to move forward through titles,
chapters or tracks on a disc.
15) MENU Button
Press to enter and exit the main DVD
menu.
E-6
811-798191W012.indd 6
4/1/2008 5:00:57 PM
UNIT AND MONITOR REFERENCE GUIDE
UNIT
MONITOR
1)
Button
Press the button and hold the front panel
to open the disc door.
SEARCH Button
2)
Press to perform fast reverse playback.
SEARCH Button
Press to perform fast forward
playback.
PREV Button
Press to select previous chapters or tracks
on a disc.
NEXT Button
Press to select next title, chapter or track
on a disc.
STOP Button
Press to stop playing a disc.
PAUSE Button
Press to pause playback and frame
advance.
PLAY Button
Press to start or resume playback of a disc.
3) STANDBY (power off) / ON Switch
4) LCD Screen
5) Headphone Jack
6) VOLUME Control
Adjusts the volume.
7) AUDIO / VIDEO OUT Jacks
8) DC IN 9V-12V Jack
9) Remote Sensor
Receives the remote control signal.
POWER ON Indicator
When the STANDBY / ON switch is in
the ON position, the green light will
illuminate.
10)Stand
1)
2)
3)
4)
5)
6)
811-798191W012.indd 7
VOLUME Control
Adjusts the volume.
Headphone Jack
AUDIO / VIDEO IN Jacks
DC OUT 9V-12V Jack
LCD Screen
POWER ON Indicator
When the ON / OFF switch is in
the ON position, the green light will
illuminate.
7) COLOR Control
Adjusts the color intensity.
8) BRIGHTNESS Control
Adjusts the relative lightness or darkness
of the screen.
9) Screen Switch
WIDE: Wide Screen
NORMAL: Pan Screen
10)ON / OFF Switch
11)DC IN 9V-12V Jack
12)Stand
E-7
4/1/2008 5:00:57 PM
POWER SUPPLY
Using the Car Power Adapter
The included 12V car power adapter is designed for use with vehicles that have a 12V, negative
ground electrical system.
Using the Main Unit and the Monitor Together
Using the Main Unit or the Monitor
CAUTION
For continued
protection against
risk of fire, replace
only with same type
and rating of fuse.
IMPORTANT
This car adapter is for use with 12 volt
batteries only.
WARNING:
Disconnect this car power adapter when
not in use. Not for use in 24V vehicles.
Cautions:
• Use this unit only with the included 12V car power adapter. Use with other car adapters could damage
the unit, or even your vehicle.
• The included 12V car power adapter is for use with this unit only. Do not use it with any other
equipment.
• In the interest of traffic safety, drivers should not operate the unit or view videos while driving.
• When the inside of the 12V car socket is dirty with ashes or dust, the power section may become hot
due to poor contact. Be sure to clean the 12V car socket before use.
• After use, disconnect the 12V car power adapter from both the unit and cigarette lighter socket.
• If the unit is not properly attached to a vehicle, it may become airborne in the event of an accident and
cause damage, injury, or death.
• Check your local traffic laws for rules governing the use of video devices in vehicles.
E-8
811-798191W012.indd 8
4/1/2008 5:00:58 PM
CONNECTIONS
A. Watching a DVD on the Main Unit and the Monitor
You can watch the same DVD on the main unit and the monitor.
1.Connect the main unit and the monitor using the included DC-AV Cable.
2.Turn on the main unit and the monitor.
3.Play a DVD on the main unit; the monitor will play at the same time.
B. Watching a TV on Main Unit
If your TV has Audio/Video inputs, you can connect the main unit to your TV using a standard
A/ V cable (not included).
Watching a DVD on your TV
1. Connect your TV to the main unit using a standard AV Cable (not included).
2. Turn on the main unit.
3.Turn on the TV and follow the instructions included with it to play the DVD.
Note:
• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause
a weak signal.
• If your TV does not have Audio/Video inputs, you will need to purchase an RF modulator (sold
separately) and follow the instructions included with it to connect the unit to your TV.
E-9
811-798191W012.indd 9
4/1/2008 5:00:58 PM
CONNECTIONS
C. Listening to a Stereo Receiver or Amplifier on the Main Unit
The main unit can play two channels Dolby Digital.
Listening on External Audio Equipment
1. Connect the main unit to the left/right Audio In jacks on the other equipment using a standard
Audio cable (not included).
2. Turn on the main unit.
3.Turn on your audio equipment and follow the instructions provided with it to select the AUDIO
IN function.
Note:
• Make sure to use the correct
Audio cable. Connecting the plugs
incorrectly may cause a weak
signal.
• If you have a stereo VCR, make sure
you set it to stereo mode.
• Due to copyright protection, DVD
movies cannot be copied. If you copy
a DVD movie onto a videotape, the
resulting copy will be unclear, with
poor sound quality. This is NOT
caused by a defective DVD system.
D. Playing a Game System/Video Equipment on the Monitor
You can connect game systems or other video equipment for playback through the monitor only.
You cannot connect these systems to the main unit.
Watching Video Equipment
1.Connect the other equipment to the monitor using a standard AV Cable (not included).
2.Turn on the monitor.
3.Turn on the video equipment and follow the instructions provided with it to playback.
Note:
• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause
a weak signal.
• If you have a mono VCR, the volume level from the speakers will be low.
E - 10
811-798191W012.indd 10
4/1/2008 5:00:58 PM
CONNECTIONS
E. Using the Monitor with Other Equipment while Playing a DVD on the Main
Unit
You can use a game console or other video equipment on the monitor while playing a DVD
on the main unit.
Watching Video Equipment with the Monitor while Playing a DVD in the Main Unit
1.Connect only the plug connector between the main unit and the monitor. Do not connect
the Audio/Video portion of the DC-AV cable.
2.Connect the monitor to the other equipment using a standard AV cable (not included).
3.Turn on the main unit, the monitor and the other equipment.
4.Play a DVD on the main unit.
5.Use the monitor for the other equipment.
Note:
• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause
a weak signal.
• If you have a mono VCR, the volume level from the speakers will be low.
F. Using Headphones/Earphones
Turn down the volume before connecting
the headphones/earphones. Slowly raise
the volume with the headphones on until
you reach your desired volume. When
headphones are connected, the speaker is
automatically disabled.
Headphones/earphones
(1/8” [3.5mm] diameter plug)
Caution:
Avoid listening to sound at excessive levels
which could be harmful to your ears.
E - 11
811-798191W012.indd 11
4/1/2008 5:00:59 PM
PLACEMENT
A. Mounting in the Vehicle
Use the supplied mounting straps to install the main unit and monitor on the back of the vehicle's
headrests. Tightly wrap the mounting strap around the headrest.
SAFETY WARNING!
• This unit should never be used by the vehicle's driver or left unsecured in the vehicle
while driving.
• If this unit is being used in your vehicle, be sure that it is secured or held safely, and does
not obstruct any safety device, including air bags or seat belts.
• All passengers should wear seat belts when using this unit in a moving vehicle.
• If in doubt, please contact your vehicle manufacturer for further advice.
E - 12
811-798191W012.indd 12
4/1/2008 5:00:59 PM
PLACEMENT
B. Using the Stand
You can stand the main unit/monitor up on a desk or table using the stand on the back.
SOUND system
Dolby Digital
Dolby Digital is a sound system developed by Dolby Laboratories Inc. This unit automatically
recognizes DVDs that have been recorded with Dolby Digital.
Not all Dolby Digital sources are recorded with 6 channels.
Some sources marked Dolby Digital may be recorded in Dolby
Surround, a 2 channel system. Look for this logo on your unit.
Manufactured under license from Dolby Laboratories.
symbol are trademarks of Dolby Laboratories.
‘Dolby’ and the double-D
E - 13
811-798191W012.indd 13
4/1/2008 5:00:59 PM
CD/DVD OPERATION
This owner’s manual explains the basic instructions of this unit. Some DVDs are produced to
limit operation during playback. For example, many DVDs do not allow users to skip government
warnings, or in some cases previews or other features. This is not a defect in the unit. Refer to the
instruction notes of discs.
” may appear on the screen during operation. A “
” means that the desired operation is
“
not permitted by the unit or disc.
Playing a Disc
1.Slide the STANDBY/ON switch to the ON position. (Slide the ON/OFF switch on the
monitor to the ON position.
See CUSTOMIZING THE DVD FUNCTION SETTINGS before proceeding to step 2.
2.Press the
button and hold the front panel to open the disc door.
3.Hold the disc by its edge and gently push it onto the spindle, with the label side facing
the front, until you hear a “click”.
4.Push the disc door gently to close it. It takes a short while for your unit to load the disc.
After loading, for most DVDs, the unit will automatically take you to the main menu
or start playing. If the unit does not automatically start playing the DVD, press the
PLAY button.
PLAYING A PICTURE FILE DISC
This unit can play picture files recorded on CD-R and CD-RW discs.
1.Press the
button and hold the front panel to open the disc door.
2.Hold the disc by its edge and gently push it onto the spindle, with the label side facing
the front, until you hear a “click”.
3.Push the door gently to close it. The picture files on the disc will be displayed one by
one automatically.
4.Press the STOP button to go to the folder list.
5.Press the
or
button to highlight a file to play. Press the
PLAY button to start
playback.
Note:
• You can press the PAUSE button to interrupt playback, and press the
PLAY button
to resume playback.
• You also can use the GOTO function or use the numbered buttons to enter the image
number to quickly select any image.
• Press the ANGLE button on the remote control to rotate the picture orientation by
90°.
Angle selection (DVD)
Some DVDs contain scenes that have been shot from a number of different angles. For
these discs, the same scene can be viewed from each of these different angles.
1.While you are playing a DVD with different angles
recorded, press the ANGLE button to view the number
of current angles available.
Sequence of angle shots
2.Press the ANGLE button repeatedly to change the scene
(Example)
to the next angle in those recorded.
•About two seconds later, playback continues from
the new angle selected.
•If no button is pressed within 10 seconds, playback
continues without changing the current angle.
Note:
• This function can only be used for discs on which scenes shot from multiple angles have
been recorded.
” is displayed.
• If only one angle is recorded, “
E - 14
811-798191W012.indd 14
4/1/2008 5:00:59 PM
SPECIAL FUNCTIONS
DISPLAY function (DVD)
While the disc is playing, press the DISPLAY button repeatedly to display information on
operation status:
Locating a specific title (DVD)
If a DVD contains title numbers, you can locate a specific title by directly selecting a
title number.
1.In STOP mode, press the GOTO button.
2.Press the or button to highlight a specific field
and press the corresponding number button(s) for the title you want.
3.Press the ENTER button to confirm. Playback starts from the selected title.
Locating a specific chapter / track
If you know the chapter / track number you want to play, you can locate a specific chapter /
track by directly selecting a chapter / track number.
1.Press the GOTO button to search for your desired
chapter / track.
2.Press the or button to highlight a chapter / track then press the corresponding number
button(s) for the chapter /track you want.
3.Press the ENTER button to confirm. Playback starts from the selected chapter / track.
Locating a specific time
You can move to a specific location by entering its corresponding time (hours, minutes,
seconds)
1.Press the GOTO button twice.
2.Press the corresponding number buttons for the setting
point you want.
3.Press the ENTER button to confirm. Playback starts from the selected location.
Note:
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as specified.
• This method for accessing specific locations is available only within the current title of
the DVD.
E - 15
811-798191W012.indd 15
4/1/2008 5:00:59 PM
REPEAT PLAYBACK
You can play a specific title or chapter repeatedly. (Chapter repeat, title repeat, A-B
repeat)
Repeating a chapter (DVD)
You can play the same chapter repeatedly.
1.While the disc is playing, press the REPEAT button until the “
displays on the screen. The current chapter is played repeatedly.
” indicator
Repeating a title
You can play the same title repeatedly.
2.While the disc is playing, press the REPEAT button until the “
on the screen. The current title is played repeatedly.
To resume normal playback
3.While the disc is playing, press the REPEAT button until the “
on the screen.
” indicator displays
” indicator displays
You can play a single track or an entire disc repeatedly.
Repeating a single track (CD)
You can play the same track repeatedly.
1.While the disc is playing, press the REPEAT button until the “
on the screen. The current track is played repeatedly.
Repeating aN ENTIRE DISC
2.While the disc is playing, press the REPEAT button until the “
on the screen. The entire disc is played repeatedly.
To resume normal playback
3.Press the REPEAT button until the “
” indicator displays
” indicator displays
” indicator displays on the screen.
Repeating a specific section (DVD / CD)
You can play a specific section repeatedly.
1.While the disc is playing, press the A-B button at the beginning of the section (
is
displayed) you want to play repeatedly.
2.Press the A-B button again at the end of the section (
is displayed) you want to play
repeatedly.
3.The unit will immediately begin replaying your selection.
To resume normal playback
4.While the disc is playing, press the A-B button until the “
” indicator displays
on the screen.
Note:
• A-B repeat can only be used within the same title. If the start and end of the section to
be repeated are in different titles, A-B repeat is cancelled.
• The A-B repeat function does not operate in scenes where different camera angles are
recorded.
E - 16
811-798191W012.indd 16
4/1/2008 5:00:59 PM
DVD PROGRAMMABLE PLAYBACK
Programmable memory
The two types of programmed playback provided by this unit is title/chapter programmed
playback.
Title/Chapter programmed playback (DVD)
1.Press the MEMORY button in PLAY mode.
2.Input the title (2 digits) and chapter (2 digits) by pressing the number buttons. (For
example : 01 02, 02 05, 02 11) It will move to the next item automatically.
3.Repeat steps 2 to add additional titles and chapters.
PLAY button to start the programmed playback.
4.Press the
CUSTOMIZING THE DVD FUNCTION SETTINGS
LANGUAGE SETUP
1.In STOP mode, press the SETUP button.
2.Use the or button to select the option (OSD
Language, Audio, Subtitle or Disc Menu), then
press the button.
3.Use the
or
button to select your preferred
language, then press the ENTER button to
confirm.
4.Press the button to go back to the previous menu.
Repeat steps 2 and 3 to adjust other options.
5.To exit the SETUP MENU and return to the normal screen, press the RETURN button.
Note:
• Some DVDs may not play in the audio language selected. A prior language may be
programmed on the disc.
• Some DVDs may be set to display subtitles in a language other than the one selected.
A prior subtitle language may be programmed on the disc.
• Some DVDs allow you to change subtitle selections via the disc menu only. If this is the
case, press the MENU button and choose the appropriate subtitle from the selection on
the disc menu.
• Some DVDs may not included your pre-selected language. In this case, the DVD player
automatically displays disc menus consistent with the disc’s initial language setting.
E - 17
811-798191W012.indd 17
4/1/2008 5:01:00 PM
CUSTOMIZING THE DVD FUNCTION SETTINGS
VIDEO SETUP
1.In STOP mode, press the SETUP button.
2.Press the
or
button repeatedly until VIDEO
SETUP appears.
3.Use the
or
button to select the option
(Brightness or Contrast), then press the button.
Use the or button to make adjustments, then
press the ENTER button. (The screen will change
to your selected setting).
4.Repeat steps 2 and 3 above to adjust other options.
5.To exit the SETUP MENU and return to the normal screen, press the RETURN button.
SYSTEM SETUP
1.In STOP mode, press the SETUP button.
2.Press the
or button repeatedly until SYSTEM
SETUP appears.
3.Use the
or
button to select the option (Tv
Display or Default), then press the button. Use
the or button to make adjustments, then press
the ENTER button. (The screen will change to your
selected setting).
4.Repeat steps 2 and 3 above to adjust other
options.
5.To exit the SETUP MENU and return to the normal screen, press the RETURN button.
TV DISPLAY
Cut off when a widescreen video image is
Pan Scan
• When wide-screen video is played, this mode clips the right and played.
left sides of the image so that it can be viewed on a conventional
screen.
• Some wide-screen DVDs that do not permit Pan Scan mode playback
are automatically played in letterbox mode (black bands that appear
at the top and bottom of the screen).
PAN SCAN
Letter Box
• When wide-screen video is played in this mode on a conventional
screen, black bands appear at the top and bottom of the screen.
Wide screen
• This is the correct mode for playing wide-screen videos on the unit
LETTER BOX
or other external wide-screens.
Note:
• The displayable picture size is preset on the DVD. Therefore the
playback picture of some DVDs may not conform to the picture
size you select.
WIDE SCREEN
• When you play DVDs recorded in the 4:3 aspect ratio, the playback
picture will always appears in the 4:3 aspect ratio regardless of the TV TYPE setting.
Default
It takes 3-5 seconds to reset the DVD settings to the factory default.
E - 18
811-798191W012.indd 18
4/1/2008 5:01:00 PM
Trouble Shooting Guide
SYMPTOM
CAUSE (AND REMEDY)
No power.
• Ensure the car power adapter is connected.
• Turn on the unit.
The remote does not
function.
• Remove any obstacles between the remote and the unit.
• Use the remote near the unit.
• Point the remote at the remote sensor on the unit.
• Replace the battery in the remote with new ones.
DVD
No sound or only a • Make sure that you’ve selected DVD mode.
very low-level sound • The system is in pause mode. Press the
PLAY button to
is heard.
return to normal play mode.
PLAY
• Fast forward or fast reverse is performed. Press the
button to return to normal play mode.
• Make sure the AUDIO / VIDEO output/input connections are
correct.
• The DTS DVD cannot be decoded to have speaker output.
• This unit is too hot. Power off the unit for 30 minutes to cool
down.
No picture
• The region number of the disc doesn’t match the region
number of this unit.
The picture is not
clear
• Clean the disc.
• The disc is scratched.
Severe hum or noise
is heard.
• The plugs and jacks are dirty. Wipe them with a cloth slightly
moistened with alcohol.
• Clean the disc.
The disc does not
play.
• There is no disc inside (“No Disc” appears on the screen).
• Insert the disc correctly with the playback side facing
frontward.
• Clean the disc.
• A non-NTSC disc has been inserted. The unit and disc region
number are incompatible.
• Condensation may have formed inside the unit due to a sudden
change in temperature. Wait about an hour for it to clear and
try again.
Specifications and appearance are subject to change without notice.
E - 19
811-798191W012.indd 19
4/1/2008 5:01:00 PM
LIMITED WARRANTY
VENTURER ELECTRONICS (“VENTURER”) makes the following limited warranty. This limited warranty extend
to the original consumer purchaser and is limited to non-commercial use of the product.
Ninety (90) Day Parts & Labor Warranty
VENTURER products purchased in the United States are warranted to be free from defects in materials or
workmanship for a period of ninety (90) days from the date of their original retail purchase. If the unit fails
to conform to this warranty, we will service the product using new or refurbished parts and products, at
VENTURER’s sole discretion.
During a period of ninety (90) days from the effective warranty date, VENTURER will provide, when needed,
service labor to repair a manufacturing defect at its designated Service Center. To obtain warranty service in
the Untied States, you must first call our Customer Support Center at 1-800-252-6123 o 1-866-444-6478,
during the hours listed in the box below. The determination of service will be made by VENTURER Customer
Support. PLEASE DO NOT RETURN YOUR UNIT TO VENTURER WITHOUT PRIOR AUTHORIZATION.
New or remanufactured replacements for defective parts or products will be used for repairs by VENTURER at
its designated Service Center for ninety (90) days from the effective warranty date. Such replacement parts or
products are warranted for an additional ninety (90) days from the date of repair or replacement. The Customer
will be required to ship the unit to the Service Center indicated at the time Customer Support is contacted to
make the necessary repairs. The customer is responsible for all transportation charges to the service facility.
Packaging and Shipping Instruction
When you send the product to the Venturer service facility you must use the original carton box and packing
material or an equivalent as designated by VENTURER.
LIMITED WARRANTY
Your Responsibility
(1)You must retain the original sale receipt to provide proof of purchase.
(2) These warranties are effective only if the product is purchased and operated in the U.S.A. or Canada.
(3) Warranties extend only to defects in material or workmanship, and do not extend to any product or parts
which have been lost or discarded, or damage to product or parts caused by misuse, accident, improper
operation or maintenance, or use in violation of instructions provided with the product, or to product
which has been altered or modified without authorization of Venturer, or to products or parts thereof
which have had the serial number removed or changed.
Out of Warranty
In the event your product requires repair after the limited warranty period has expired, please contact our
Customer Support Center at 1-800-252-6123, 1-866-444-6478 or www.venturer.com
Hours: Monday–Thursday: 9–7, Friday: 9–5, Saturday: 9–12 EST.
Important:
You are responsible for any transportation, shipping or insurance relative to the
return of product to our Product Returns Center.
All warranties implied by state law, including the implied warranties of merchantability and fitness for a
particular purpose, are expressly limited to the duration of the limited warranties set forth above. With the
exception of any warranties implied by state law as hereby limited, the foregoing warranty is exclusive and
in lieu of all other warranties, guarantees, agreements and similar obligations of manufacturer or seller with
respect to the repair or replacement of any parts. In no event shall VENTURER be liable for consequential or
incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these
warranties in any manner whatsoever. The time within action must be commenced to enforce any obligation
of VENTURER arising under the warranty or under any statute, or law of the United States or any state thereof,
is hereby limited to ninety (90) days from the date of purchase. This limitation does not apply to implied
warranties arising under state law.
This warranty gives you specific legal rights and you may also have other rights, which may vary, from state
to state. Some states do not allow limitation on how long an implied warranty lasts, when an action may be
brought, or the exclusion or limitation of incidental or consequential damages, so the above provisions may
not apply to you.
For more information on other products and services, please visit out website at www.venturer.com.
Important: Also keep your “Bill of Sale” as proof of purchase.
Model no. ............................................................ Product name .....................................................
Type of set ..............................................................................................................................................
Serial no. .............................................................. Invoice no. .............................................................
Date purchased .................................................... Dealer name ..........................................................
© 2008 VENTURER Electronics Inc.
811-798191W012.indd 20
E - 20
Printed in China
811-798191W012
4/1/2008 5:01:00 PM
Download PDF