Briggs & Stratton | REL-HPU-2000 | REL-HPU-2000 - Reliable Equipment

REL-HPU-2000
18 HP Gasoline/Hydraulic
2,000 PSI - PUMP
Meets HTMA
performance standards.
SPECIFICATIONS
Engine: Briggs & Stratton
Vanguard - V-Twin
18 HP
Flow Range:
5-8 GPM
20 or 30 lpm
Operating Pressure:
2,000 PSI
140 bar
Circuit Type:
Open Center
Hydraulic Reservoir:
3 Gallons
11 liters
Fuel Tank:
7 Gallons
26.5 liters
Height:
29 inches
73.7 cm
Length (Handle Down):
35 inches
89 cm
Width:
21.5 inches 54.6 cm
Weight
330 lbs.
150 kg
RELIABLE EQUIPMENT & SERVICE CO., INC.
92 STEAMWHISTLE DRIVE • IVYLAND, PA 18974
TOLL FREE: 800-966-3530 • FAX: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
4
The REL-HPU-2000
provides the power needed to operate
any standard Type I or Type II hydraulic
equipment. The Briggs & Stratton
18 hp gasoline engine delivers up to
2,000 psi of hydraulic pressure, at
either user selected flow setting of
5 or 8 gallons per minute.
Automatic throttling feature ensures
consistent performance throughout
tool operation.
The oil cooler with high speed blower
reduces operating temperatures and
related system wear.
The electric start, flow selector, and
control valve are located on the front
panel for operator convenience, while
the choke, fuel fill, and hour meter
remain within easy reach.
The easy access battery compartment
located at the front of the unit holds
a 35-Ah maintenance-free battery.
The convertible handle and 12 inch
pneumatic tires provide ease of
movement into hard to access areas.
Shown With
Optional WJ-1137-P
7/16” H -1/2” SQ.
REL-425C
HYDRAULIC IMPACT WRENCH
SPECIFICATIONS
System
Open/Closed Center
4 -8 gpm (opt. 5-8 gpm)
1,000-2,000 psi
425 ft.-lb. @ 6 gpm
3,600 @ 6 gpm
REL-425C
HYDRAULIC IMPACT WRENCH
WITH 7/16” QC CHUCK
The REL-425C hydraulic impact wrench
was designed with an E-Z selector for use
on both open or closed center hydraulic
systems. It’s lightweight (just 6.3 lbs.),
makes it the ideal tool for use on utility
pole construction.
The REL-425C delivers 425 ft.-lb. torque
at 6 gpm making it great for drilling,
loosening rusted hardware or tightening
lag bolts with ease. A 7/16" quick change
chuck is included for your convenience.
Weight: 6.3 lbs., Size: 8.6" x 8.8" x 2.7"
REL-IH
IMPACT HOLSTER
The REL-IH will
protect your impact.
Bracket fits up to a
2-1/2“ lip. Mount inside or
outside of bucket. Side cutout
allows quick, easy tool placement and
removal with or without a drill bit and chuck.
9 2 St e a m w h i s t l e D r i v e I v y l a n d , PA 1 8 9 7 4
Phone: 800-966-3530 Fax: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
REL-EA250
HYDRAULIC AUGER
POST HOLE
DIGGER
Operate from any
2,000 PSI Hydraulic
Power Source
Shown with
Optional Auger
The REL-EA250 Hydraulic Earth Auger
can be used in boring applications for
pole, post, and fence installations.
The REL-EA250 “X” Handles offer
easy two person operation.
The Torque Anchor Bar offers safe
one person operation.
The safety control valve is reversible,
simplifying the augers’
removal from the hole.
PERFORMANCE
250 ft. lb. (339 Nm)
CAPACITY (Long Auger)
2 to 18 in. Dia. x 42 in. (46 X 107 cm ) + Extensions
FLOW RANGE
7 - 9 gpm (26 - 34 lpm)
PRESSURE
up to 2,000 psi (up to 138 bar)
PORTS / CONNECTION
-8 SAE O-Ring / 3/8 in. FF Quick Couplers
TORQUE ANCHOR BAR
75 - 141 in. (190 - 358 cm)
SPEED (at 8 gpm/30 lpm)
165 rpm
Weight: 47 lbs. (21kg) w/o torque bar
Height: 11.7 inch (30 cm) w/o auger
Width: 46 inch (119 cm) w/ handles
RELIABLE EQUIPMENT & SERVICE CO., INC.
92 STEAMWHISTLE DRIVE • IVYLAND, PA 18974
TOLL FREE: 800-966-3530 • FAX: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
4
REL-TMP
HYDRAULIC POLE TAMPERS
REL TMP 72
Valve on Tube
REL TMP 60V
Valve on Hose
Reliable’s REL-TMP Series will make quick
work of setting poles, asphalt patch and
general construction backfill compacting.
Only 3 moving parts for low maintenance.
Reversible On/Off valve for Open- and
Closed-Center systems (hose-end models).
REL TMP 60
Hose on Tube
Standard with kidney-shaped foot.
Rotate trigger selector for Open and Closed
Center systems (valve on tube models).
TAMPER - OPTIONS
REL TMP 72
72” Tamper Valve on Tube
REL TMP 60
60” Tamper Direct Coupled
REL TMP 60V 60” Tamper Direct Coupled
SPECIFICATIONS
Width: 4"
Flow Range: 4-6 gpm
Pressure: 1,000-2,000 psi
Pressure Port Thread: 9/16-18 SAE O-Ring
Return Port Thread: 3/4-16 SAE O-Ring
Standard Foot Size: 2.5 x 8" kidney-shaped
Blows Per Minute: 1,160 @ 5 gpm
Consult your RELIABLE
representative for more
information about our complete
line of hydraulic tools.
Shown with
Kidney Shaped
Pole Foot
RELIABLE EQUIPMENT & SERVICE CO., INC.
92 Steamwhistle Drive Ivyland, PA 18974
Phone: 800-966-3530 Fax: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
REL-SPD
HYDRAULIC SIGN POST DRIVER
The REL-SPD Sign Post Driver will drive
posts of almost any configuration, including
“U” channel, round, square, T-post and more.
The REL-SPD is fitted to accomodate most
common post types, providing greater control
throughout the post installation. Reducing
operator fatigue due to indirect motion,
and limiting damage to the top of the post.
A balanced lifting eye, in-line control valve,
and dual full legth cushion grip handles
simplify lifting and operation in raised
applications.
Optional post adapters are available to
accomodate custom or regional post
styles.
The REL-SPD meets State Department
of Transportation (DOT) requirements for
driving breakaway posts and delineators.
capable of driving posts to within 4 inches
(100 mm) above ground level.
Capacities
70 lbs.
28.5 in. X 8 in. X 9 in.
92 Steamwhistle Drive Ivyland, PA 18974
Phone: 800-966-3530 Fax: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
REL-SPD without accessory adapters
#2, #3 and #4 lb./ft. “U” Channel Sign Post
#3 & #4 Strong Back “U” Channel Sign Post
#1 Delineator Post
2-1/2 in. (63.5 mm) Square Post
2-5/8 in. (67 mm) Round Post
REL-SPD with Adapters (See Next Page)
1 3/4” Round (T-Post)
1 3/4” Square Post
2” Round Pipe
2” Square Post
2 1/4” Square Post
Custom Sign Post Driver Accessories
5 Styles
R-SPD-200R
R-SPD-200S
2 ” Round
2 ” Square
R-SPD-175R
R-SPD-175S
R-SPD-225S
1-3/4 ” Round
1-3/4 ” Square
2-1/4 ” Square
REL-SPD
BASE
VIEW
SIDE
VIEW
ADAPTER
Sign Post Driver Accesories
Five custom Sign Post Adapters and
one Drive Gad are available for use
with the REL-SPD Sign Post Driver.
When the custom sign post adapters
are installed into the front housing of
the driver it will provide a positive guide
for the post. The adapter guarantees
that the full force of the hammer falls
squarely onto the end of the post.
Less movement and increased drive
force will result in the post being driven
faster, cleaner and more true.
The Drive Gad has been designed to
allow Break-Away posts to be driven
to within 4 inches above ground level.
Adapters
Part #
R-SPD-175R
R-SPD-200R
R-SPD-175S
R-SPD-200S
R-SPD-225S
Shape
Round
Round
Square
Square
Square
I.D. Size
1-3/4 ”
2”
1-3/4 ”
2”
2-1/4 ”
Drive Gad
R-SPD-DGS
Square
2 ”- 2-1/4 ”
DRIVE GAD
REL-SPP
HYDRAULIC SIGN POST PULLER
Integrated
Control Valve
Features Gripping Jaw and
Chain Operation to Handle Flanged
and Irregular Poles up to
8 inches in diameter.
Weight: 70 lbs.
Length: 12.75”
Width:
14”
Height: 18.75”
(Retracted)
REL-SPP
SPECIFICATIONS
HYDRAULIC SIGN POST PULLER
The REL-SPP will pull flanged type and
irregular shaped sign posts and poles up
to 8 inches in diameter.
System
Hydraulic
Pressure
2,000 psi (140 bar)
Flow Range
3-9 gpm (11-34 lpm)
Pulling Force
9,800 lbs. (4,450 kg) @ 2,000 psi
Capacity
Up to 8 inch diameter (20 cm)
Pull flanged type posts using the gripping
jaw, or utilize the included chain to wrap
around the pole and secure in the frame slots.
The REL-SPP combines 9,800 lbs. of
pulling force with an 8 inch stroke to provide
the power for almost any application.
4
92 Steamwhistle Drive Ivyland, PA 18974
Phone: 800-966-3530 Fax: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
REL-SP2
2 INCH SUBMERSIBLE
HYDRAULIC PUMP
The REL-SP2 Submersible Pump is a
light weight, efficient way to move large
quantities of liquids FAST.
W
E
N
No priming required!
The REL-SP2 is also able to pump
petroleum products.
The REL-SP2 is able to run all day
without seal damage.
2” Compact, lightweight Submersible Pump
Operate on Open and closed center systems.
X-Long carry handle aids in placement.
High impact strainer housing.
Whip set and flush-face couplers included.
Can run dry without damage.
Specifications
Capacity: Up to 275 GPM
Flow Range: 5-8 GPM
Operating Pressure: 1200-2000 PSI
Intake Port: 1 15/16” (49mm)
Discharge Port: 2” NPFT (51mm)
Height: 14” (over handle)
Width: 8-1/2” x 9-1/2” diameter
Weight: 15 lbs.
RELIABLE EQUIPMENT & SERVICE CO., INC.
92 STEAMWHISTLE DRIVE • IVYLAND, PA 18974
TOLL FREE: 800-966-3530 • FAX: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
REL-TP3
3 Inch Hydraulic
Trash Pump
The REL-TP3 Submersible Trash
Pump is the lightest, most efficient way
to move large quantities of liquids with
concentrations of solids up to 3 inches
in diameter and 30% by volume.
No priming required!
These urethane pumps have a history
of pumping sand, gravel, concrete,
and even mortar slurries without issue.
The REL-TP3 is also able to pump
petroleum products.
The REL-TP3 is able to run all day
without seal damage (450 GPM).
The urethane bowl and impeller are
extremely durable and light weight. Hard
and sharp materials bounce off instead
of abrading the interior surfaces, making
this design last longer and perform
better than aluminum, iron and even
steel pumps.
92 Steamwhistle Drive • Ivyland, PA 18974
Phone: 800-966-3530 • Fax: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
HYDRAULIC LONG REACH CHAINSAW
Reliable’s LR-Series long reach chainsaws
are intended for safely cutting and trimming trees
from the ground or an aerial bucket. The powerful
hydraulic drive motor can easily make cuts up to
13 inches in diameter. With an overall length up to
88.5 inches, the operator may easily reach areas
not possible with a standard chain saw.
The dielectric property of the fiberglass extension
tube will reduce the chance of electric shock when
used near an energized electric line. Other features
include a trigger guard t o p r e v e n t a c c i d e n t a l
movement of the chain, a covered sprocket guard,
and a rubber collar hand stop. A quick set spool can be
turned 180O for closed center/open center operations.
LR-88.5
LR-75
FEATURES:
LR-62.5
88.5 inch, 75 inch & 62.5 inch Models Available
Insulated fiberglass extension tube - reduce risk
of electrical shock when used near an energized line.
Automatic Chain Oiler - provides continuous
lubrication to the chain and guide bar while the saw
is running, minimizing wear and extending tool life.
Trigger Guard - prevent accidental chain movement.
Quick Set Spool - may be turned 180 O for open or
closed center operations.
15” Bar - Allows a 13” cutting capacity.
Covered Sprocket Guard.
Rubber Collar Hand Stop.
Meets OSHA 1910.269
SPECIFICATIONS:
Cutting Capacity: 13 in.
Weight: 9.5 lbs.
Flow Range: 5-8 gpm
Cutting Chain: 4,200 fpm/min. @ 8gpm
Operating Pressure: 1,000-2,000 psi
Pressure & Return Port Thread: 3/8" NPTF
Chain Size: .325 in. pitch
Chain Gauge: .058 in.
CONTACT RELIABLE EQUIPMENT
Call: 800-966-3530 Fax: 215-357-9193
NEW LR-CS-82
HYDRAULIC LONG REACH CIRCULAR SAW
Reliable’s LR-Series long reach saws are intended for safely
trimming trees from the ground or an aerial bucket. With an
overall length of 82 inches, the operator may easily reach areas
not possible with a standard chain saw. The offset head
provides a flush cut, from a comfortable stance, reducing
operator fatigue and strain.
The powerful hydraulic drive motor can easily cut branches up to
3.5 inches in a single pass. The quick stop trigger reduces blade
coast time for increased safety. The dielectric property of the
fiberglass extension tube will reduce the chance of electric shock.
FEATURES:
Insulated fiberglass extension tube - reduces risk of
electrical shock when used near an energized line.
Quick Stop System - reduces blade coast time.
Trigger Guard - prevents accidental blade activation.
Quick Set Spool - Locked in the Open-Center position at factory.
9” Blade - Allows a 3.5 inch cutting depth.
Rubber Collar Hand Stop.
SPECIFICATIONS:
Meets OSHA
Weight: 9.3 lbs. Lenght: 82 inches
Flow Range: 5-8 gpm
Blade Speed: 4,800 RPM @ 6 gpm
Operating Pressure: 1,000-2,000 psi
Pressure & Return Port Thread: # 6 SAE & # 8 SAE
Blade Diameter: 9 inches
Blade Thickness: .1/16 inch
Arbor: 0.635” x 0.878 inch
Blade Operating RPM: 5,400 (minimum)
1910.269
RELIABLE EQUIPMENT & SERVICE CO., INC.
92 STEAMWHISTLE DRIVE • IVYLAND, PA 18974
TOLL FREE: 800-966-3530 • FAX: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
REL-CS16
HYDRAULIC CHAIN SAW
REL-CS16 - HYDRAULIC CHAIN SAW
The REL-CS16 hydraulic chain saw is the perfect tool for line
clearance, right of way, pruning, and tree removal applications.
This workhorse features a 16 inch cutting capacity, a powerful
motor, selector control for Open and Closed Center systems,
and a reduced kickback bar and chain.
The chain and bar are adjustable without removing the
sprocket cover. The automatic chain oiler can be adjusted
without tools. The sprocket cover can be easily removed for
saw cleaning.
SAFETY FEATURES:
Reduced Kickback Bar and Chain
Two Step Safety Trigger
Chain Catcher
Front Handle Shroud
Rear Handle Guard
At around half the weight of many
professional gasoline chain saws
the REL-CS16 hydraulic chain saw
boasts more power to the pound.
ACCESSORIES
R29201
Bar
Chain
SPECIFICATIONS:
Cutting Capacity: 16 inch
Weight: 9.5 lbs. (complete)
System: Open or Closed Center
Flow Range: 4-8 gpm
Operating Pressure: 1,000-2,000 psi
Pressure Port Thread: 9/16” -18 SAE O-ring
Return Port Thread: 3/4” -16 SAE O-ring
Chain Size: 3/8 in. pitch
Chain Gauge: .050 in.
R29200
6-3/8F50F-S
Adapters
8-3/8F50F-S
Coupler Set
FF-370-6FP
CONTACT RELIABLE EQUIPMENT Call: 800-966-3530 Fax: 215-357-9193
REL-58MC
MANUAL HYDRAULIC
CUTTING TOOL
6 TONS OF CUTTING FORCE
REL-58MC
MANUAL HYDRAULIC CUTTER
Among the smallest hydraulic cutting tools
available. Designed to cut copper, aldrey,
aluminum, aluminum-steel cables, EHS guy
wire and steel ropes having a max overall
diameter of 1” and steel ground rod up to 5/8”.
The tool features a double speed action.
The blades are manufactured from high
strength special steel, heat treated to ensure a
long service life.
The head can rotate by 180 degrees, to enable
the operator to work in the most comfortable
position, and can easily be opened to allow the
cutting of running cables. REL-58MC features
an automatic safety valve to bypass oil when
reaching maximum pressure; a pressure
release device can also be operated at any
stage of operation.
SPECIFICATIONS
Length
Weight
15.75 inches
7.7 lbs.
Pressure
10,000 psi (manual)
Capacity
1 in. Al., Guy Wire, Steel Rope
5/8 in. Steel Ground Rod
92 Steamwhistle Drive • Ivyland, PA 18974
Phone: 800-966-3530 • Fax: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
RELIABLE
EQUIPMENT
www.Reliable-Equip.com
REL-1215P-SNAP
REL-1215P-SNAP
REL-1579
TOOL BUCKET W/ HOOKS
CANVAS NOSE BAG WITH SNAP
12” Round Top & 15” Sidewall
5-1/2 X 5-1/2 X 3” Internal Pocket
Leather ReInforced Synthetic Rope Handle
12” Flexible Plastic Bottom with Risers
Rolled Edge Protection
15” Long x 7 Wide x 9” Deep
15 ReInforced Internal Pockets
2 Yellow Polymer Hooks Brass Grommets
Heavy Wieght Canvas & ReInforced Stitching
Flexible Plastic Bottom with Risers and
(2) Drain Holes
REL-BH
BUCKET MOUNT
LIGHT HOLDER
RECHARGEABLE BOX LIGHTS
REL-45116 - Industrial - can be charged with AC or DC power for maximum versatility.
REL-45107 - Truck Mount - Hard wire rack mounts to the DC system of any Utility, Fire, or Safety vehicle.
92 Steamwhistle Drive Ivyland, PA 18974
Phone: 800-966-3530 Fax: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
Download PDF