BOXLIGHT | CD715x | User manual | BOXLIGHT CD715x User manual

CD715x
Downloaded From projector-manual.com Boxlight Manuals
USER MANUAL
19462 Powder Hill Place
Poulsbo, WA 98370
800.762.5757
360.779.7901
www.boxlight.com
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
© Copyright September, 2004
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
All product names used in this manual are the properties of their respective owners and are acknowledged.
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Important Safety Information
Congratulations on purchasing the DLP projector!
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years safe use of the projector. Keep
this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following boxes are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”
Main Features
•
Lightweight unit, easy to pack away and transport
•
Compatible with all major video standards including NTSC, PAL, and SECAM
•
A high brightness rating allows for presentations in daylight or in lit rooms
•
Supports resolutions up to XGA at 16.7 million colors to deliver crisp, clear images
•
Flexible setup allows for front rear and ceiling projection
•
Line-of-vision projections remain square, with advanced keystone correction for angled
projections
•
Input source automatically detected
— ii —
Downloaded From projector-manual.com Boxlight Manuals
PPrreeffaaccee
Remote Control
The remote control has a laser for pointing out items on a screen.
DANGER: Do not point the laser in the eyes. Doing so can damage the eyes permanently.
General Safety Information
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
Do not place the unit on an unstable surface, cart, or stand.
Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.
Power Safety
Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. Refer to “Replacing the Projection Lamp”
on page 26 for clear and safe instructions for this procedure.
Unplug the power cord.
Allow the lamp sufficient time to cool.
Cleaning the Projector
Unplug the power cord before cleaning. Refer to “Cleaning the Projector” on page 28.
Allow the lamp sufficient time to cool.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the “Regulatory Compliance” section on page 39.
About this manual
This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one
page. This printer-friendly format is both for your convenience and to help save paper and thereby protect
the environment. It is suggested that you only print sections that are relevant to your needs.
– iii –
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Table of contents
GETTING STARTED .......................................................................................................................................................... 1
PACKING CHECKLIST ........................................................................................................................................................... 1
VIEWS OF PROJECTOR PARTS ............................................................................................................................................... 2
Front-left view................................................................................................................................................................. 2
Top view—OSD buttons and LEDs ................................................................................................................................. 3
Rear view—connectors ................................................................................................................................................... 5
Bottom view..................................................................................................................................................................... 7
REMOTE CONTROL PARTS ................................................................................................................................................... 8
REMOTE CONTROL OPERATING RANGE ............................................................................................................................... 9
PROJECTOR AND REMOTE CONTROL BUTTONS .................................................................................................................. 10
SETUP AND OPERATION............................................................................................................................................... 11
INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................. 11
CONNECTING INPUT DEVICES ............................................................................................................................................ 12
STARTING AND SHUTTING DOWN THE PROJECTOR ............................................................................................................. 13
ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 14
ADJUST THE ZOOM, FOCUS AND KEYSTONE ...................................................................................................................... 15
ADJUSTING THE VOLUME .................................................................................................................................................. 16
ON-SCREEN DISPLAY MENU SETTINGS................................................................................................................... 17
ON-SCREEN DISPLAY MENU CONTROLS ........................................................................................................................... 17
Navigating the OSD ...................................................................................................................................................... 17
Setting the OSD Language............................................................................................................................................ 18
Main Menu.................................................................................................................................................................... 19
Setup Menu ................................................................................................................................................................... 21
Config Menu ................................................................................................................................................................. 22
Utility Menu .................................................................................................................................................................. 23
Language Menu ............................................................................................................................................................ 24
Status Menu................................................................................................................................................................... 25
MAINTENANCE AND SECURITY................................................................................................................................. 26
REPLACING THE PROJECTION LAMP................................................................................................................................... 26
Resetting the Lamp........................................................................................................................................................ 27
CLEANING THE PROJECTOR................................................................................................................................................ 28
Cleaning the Lens ......................................................................................................................................................... 28
Cleaning the Case ......................................................................................................................................................... 29
USING THE KENSINGTON LOCK ......................................................................................................................................... 29
TROUBLESHOOTING ..................................................................................................................................................... 30
COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 30
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 30
LED ERROR MESSAGES .................................................................................................................................................... 31
IMAGE PROBLEMS .............................................................................................................................................................. 31
LAMP PROBLEMS ............................................................................................................................................................... 32
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 32
AUDIO PROBLEMS ............................................................................................................................................................. 32
HAVING THE PROJECTOR SERVICED .................................................................................................................................. 33
SPECIFICATIONS............................................................................................................................................................. 34
SPECIFICATIONS................................................................................................................................................................. 34
Input/output connectors ................................................................................................................................................ 35
PROJECTION DISTANCE VERSUS PROJECTION SIZE............................................................................................................. 36
TIMING MODE TABLE ........................................................................................................................................................ 37
DIMENSIONS ...................................................................................................................................................................... 38
REGULATORY COMPLIANCE ..................................................................................................................................... 39
FCC WARNING .................................................................................................................................................................. 39
CANADA ............................................................................................................................................................................ 39
SAFETY CERTIFICATIONS ................................................................................................................................................... 39
EN 55022 WARNING ......................................................................................................................................................... 39
— iv —
Downloaded From projector-manual.com Boxlight Manuals
GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
DLP PROJECTOR WITH LENS CAP
250V POWER CABLE
USB CABLE
CD-ROM (THIS USER’S MANUAL)
REMOTE CONTROL
(WITH TWO AAA BATTERIES)
S-VIDEO CABLE
MULTI-LANGUAGE QUICK START GUIDE
COMPUTER CABLE (DVIDB15)
CARRYING CASE
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work.
Caution:
1.
Avoid using the projector in dusty environments.
2.
Leave the power cable plugged in (for 5-10 minutes) until the projector returns to room temperature before
placing the projector inside the soft case. Placing the projector into the case soon after switching off the power
could cause the projector to break down. Be sure to attach the lens cap and place the projector into the soft
case with the lens facing upward.
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Views of Projector Parts
Front-left view
1
8
ITEM
1.
7
6
LABEL
4
DESCRIPTION
Zoom
2.
5
3
2
Enlarges the projected image
See OSD buttons and LEDs below
SEE PAGE:
15
3
3.
Projection lamp cover
Remove when changing lamp
26
4.
IR receiver
Receiver for IR signal from remote control
9
5.
Lens/focus
Remove cover, turn the lens to focus
15
6.
Height adjuster
Adjusters drop down when adjuster button is
pushed
14
7.
Height adjuster button
Push to release height adjuster
8.
Speaker
Built-in mono speaker
Important:
Grill openings on the projector allow for good air circulation, which keeps the projector lamp cool.
Do not obstruct any of the grill openings.
–2–
Downloaded From projector-manual.com Boxlight Manuals
G
Geettttiinngg SSttaarrtteedd—
—VViieewwss ooff PPrroojjeeccttoorr PPaarrttss
Top view—OSD buttons and LEDs
1
2
3
4
READY
POWER
KEYSTONE
5
POWER
6
SOURCE
7
VOL -
VOL +
AUTO
MENU
11
ITEM
1.
9
10
LABEL
Volume/
left cursor
8
DESCRIPTION
SEE PAGE:
Decreases volume
Navigates and changes settings in the OSD
16
2.
Keystone/
Up cursor
Corrects image-trapezoid (narrower top) effect
Navigates and changes settings in the OSD
3.
Ready (LED)
Orange
Lamp ready—you can safely turn on or off the projector
Flashing
Lamp not ready—do not press the power button
4.
Power
Turns the projector on or off (main power switch must
be turned on first, see item 8 on page 5)
5.
Power (LED)
Green
Unit is powered on and working correctly
Off
Unit is powered off
Flashing
Operational error code
(refer to “LED Error Messages” on page 31)
13
6.
Source
Detects the input device
13
7.
Volume/
right cursor
Increases volume
Navigates and changes settings in the OSD
17
–3–
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
ITEM
LABEL
DESCRIPTION
8.
Auto
Optimizes image size, position, and resolution
9.
Menu
Opens/exits the On-Screen Display (OSD)
10.
Enter
Changes settings in the OSD
11.
Keystone/
Down cursor
Corrects image-trapezoid (narrower bottom) effect
Navigates and changes settings in the OSD
–4–
Downloaded From projector-manual.com Boxlight Manuals
SEE PAGE:
18
G
Geettttiinngg SSttaarrtteedd—
—VViieewwss ooff PPrroojjeeccttoorr PPaarrttss
Rear view—connectors
1
18
ITEM
2
3
17 16 15 14
4
13 12 11 10
LABEL
5
9
6
8 7
DESCRIPTION
1.
DVI-I
Connect the DVI cable (supplied) from a computer
2.
RGB IN
Connect a VGA cable (not supplied) from a computer
3.
RGB OUT
Connect to a monitor
4.
RS-232
Installation control and firmware upgrades
5.
USB
Connect the USB cable (supplied) from a computer
6.
Audio-in
Connect the audio cable (supplied) from the input device
7.
Power connector
Connect the supplied power cord
8.
Main power
Turns the main power on or off
9.
IR receiver
Receiver for IR signal from remote control
10.
Audio-out
Audio loop-thru
11.
Audio-in-R
Connect an RCA audio cable (not supplied) from the input
device right channel
12.
Audio-in-L
Connect an RCA audio cable (not supplied) from the input
device left channel
13.
Video
Connect a composite video cable (not supplied)from a
video device
14.
S-video
Connect the supplied S-video cable from a video device
15.
Kensington Lock
Secure to permanent object with a Kensington Lock system
SEE PAGE:
13
–5–
Downloaded From projector-manual.com Boxlight Manuals
9
13
29
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
ITEM
LABEL
16.
Pr/Cr
17.
Pb/Cb
18.
Y
Component
video in
DESCRIPTION
Connect a component video enabled device
SEE PAGE:
13
Note:
If your video equipment has both S-video and RCA jacks (composite video) connect to the S-video
connector.
S-video provides a better quality signal.
–6–
Downloaded From projector-manual.com Boxlight Manuals
G
Geettttiinngg SSttaarrtteedd—
—VViieewwss ooff PPrroojjeeccttoorr PPaarrttss
Bottom view
1
ITEM
2
3
LABEL
3
3
DESCRIPTION
2
1
SEE PAGE:
1.
Height adjuster buttons
Push to release height adjusters
2.
Height adjusters
Adjusters drop down when adjuster buttons
are pushed
3.
Ceiling support holes
Contact your dealer for information on mounting the projector on a
ceiling.
–7–
Downloaded From projector-manual.com Boxlight Manuals
14
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Remote Control Parts
2
1
3
22
21
20
Power
Auto
4
Source Freeze Blan
k
5
Menu
Enter
6
7
8
9
10
19
18
17
16
Volume
15
Mute Keystone
11
12
1
2
13
14
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between remote and projector is obstructed, you can bounce the remote signal off certain reflective
surfaces such as projector screens.
–8–
Downloaded From projector-manual.com Boxlight Manuals
G
Geettttiinngg SSttaarrtteedd—
—VViieewwss ooff PPrroojjeeccttoorr PPaarrttss
ITEM
LABEL
DESCRIPTION
1.
Laser
Use as on-screen pointer. DO NOT POINT IN EYES.
2.
IR transmitter
Transmits signals to projector
3.
Status LED
Lights when the remote control is used
4.
Auto
Optimizes image size, position, and resolution
5.
Blank
Makes the screen blank
6.
Enter
Changes settings in the OSD
7.
Up cursor
SEE PAGE:
9
22
17
Navigates and changes settings in the OSD
8.
Right cursor
9.
Cursor pad
10.
Keystone top
11.
Keystone bottom
12.
Mute
Mutes the built-in speaker
13.
Right mouse
Functions as right mouse button when connected to a PC
14.
Left mouse
Functions as left mouse button when connected to a PC
15.
Volume down
16.
Volume up
17.
Down cursor
18.
Left cursor
19.
Menu
Opens the On-Screen Display (OSD)
20.
Freeze
Freeze/unfreezes the on-screen picture
21.
Source
Detects the input device
22.
Power
Turns the projector on or off
Moves the on-screen cursor when connected to a PC
Corrects image-trapezoid (narrower top/bottom) effect
15
16
Adjusts volume
Navigates and changes settings in the OSD
17
13
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote functions within a radius of about (7) meters (23 feet) and 30 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
–9–
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however the buttons on the projector are limited in use. The following illustration shows the corresponding buttons on the remote control and on
the projector.
7/10
13
12
Power
Auto
Source Freeze
Blank
1
13
READY
KEYSTONE
Menu
11
10
9
8
7
3/5
Enter
2
POWER
POWER
12
3
4
Volume
1
Mute Keystone
SOURCE
4/8
VOL -
VOL +
AUTO
5
6
MENU
1
11
2
6/9
2
Some buttons on the projector have two functions. For example, item 7/10 on the projector functions
both as the volume down button and as the left cursor key in OSD menus.
– 10 –
Downloaded From projector-manual.com Boxlight Manuals
SETUP AND OPERATION
Inserting the Remote Control Batteries
1.
2.
3.
Remove the battery compartment cover
by sliding the cover in the direction of
the arrow.
Insert the supplied batteries taking note
of the polarity (+/-) as shown here.
Replace the cover.
Caution:
1. Only use AAA alkaline batteries.
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Connecting Input Devices
A PC or notebook computer as well as video devices can be connected to the projector at the same time.
Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras.
Check the user manual of the connecting device to confirm it has the appropriate output connector.
A
B
DVI-I IN
RGB IN
Y
ITEM
PB/CS
D
C
RS-232C
RGB OUT
E
USB
F
AUDIO-IN
PR/CR
COMPONENT VIDEO IN
S-VIDEO IN
VIDEO IN
L-AUDION IN -R
AUDIO OUT
K
J
I
H
G
LABEL
DESCRIPTION
A
DVI-I
Connect the supplied DVI cable from a computer.
B
RGB in
Connect a VGA cable (not supplied) from a computer.
C
RGB out
Connect a VGA cable (not supplied) to a monitor.
D
RS-232
Reserved for installation control and firmware upgrades.
E
USB
Connect the supplied USB cable from a computer.
F
Audio-in
Connect an audio cable (not supplied) from the computer’s audio-out connector.
G
Audio-out
Audio loop-thru
H
L-Audio in-R
Connect the audio cable (not supplied) from an audio input device.
Video
Connect a composite video cable (not supplied) from a video device.
S-video
Connect the supplied S-video cable from a video device.
Component
video in
Connect a component video cable (not supplied) from a video device.
I
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
– 12 –
Downloaded From projector-manual.com Boxlight Manuals
SSeettuupp aanndd O
Oppeerraattiioonn
Starting and Shutting down the Projector
1.
Connect the power cord to the projector. Connect the other end to a wall
outlet. (A)
Turn on the power switch. (B)
The Power LED and Lamp-ready LED
turn on.
Remove the lens cover.
3.
Turn on the connected devices.
4.
ON
OFF
2.
Ensure the Lamp-ready LED is on a
steady (not flashing) orange and then
press the Power button to turn on the
projector.
The projector splash screen displays
and connected devices are detected.
If the connected device is a PC, press
the appropriate Fn hot keys on the
computer keyboard to switch the display output to the projector. (Check the
PC user manual to determine the appropriate Fn hot keys to change display
output.)
5.
6.
7.
If more than one input device is connected, press the Source button
repeatedly to switch among devices.
To turn off the projector, press the
Power button. The projector prepares
for shutdown and a “Wait a moment
please…” message appears.
When the “Power Off?/Press Power
again” message appears, press the
Power button. The projector turns off.
Attention : Power off the projector normally and unplug the power cord before moving the projector
– 13 –
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Adjusting the Projector Level
Take note of the following when setting up the projector:
•
The projector table or stand should be level and sturdy.
•
Position the projector so that it is perpendicular to the screen.
•
Be sure cables are not in the way or can cause the projector to be knocked over.
1.
To raise the level of the projector, lift the projector [A] and press the height-adjuster
buttons [B].
The height-adjusters drop down [C].
2.
To lower the level of the projector, press the height-adjuster buttons and push down
on the top of the projector.
– 14 –
Downloaded From projector-manual.com Boxlight Manuals
SSeettuupp aanndd O
Oppeerraattiioonn
Adjust the Zoom, Focus and Keystone
1.
2.
3.
Use the Image-zoom control (on the projector only)
to resize the projected image and screen size A .
Use the Image-focus control (on the projector only)
to sharpen the projected
image B
Use the Keystone buttons
(on the projector or the
remote control) to correct
image-trapezoid (wider
top or bottom) effect.
The keystone control appears on the display.
– 15 –
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Adjusting the Volume
1.
2.
3.
4.
Press the Volume +/- buttons on the projector or
the remote control.
The volume control appears on the display.
Use the Volume +/- buttons to adjust the level.
Press the Mute button (on
the remote control only)
to turn off the volume.
Press Volume +/- or
Mute on the remote control to turn off mute.
– 16 –
Downloaded From projector-manual.com Boxlight Manuals
ON-SCREEN DISPLAY MENU SETTINGS
On-Screen Display Menu Controls
The projector has an On-Screen Display (OSD) that lets you make image adjustments and change
various settings.
Navigating the OSD
You can use the remote control or the buttons on the top of the projector to navigate and make
changes to the OSD. The following illustration shows the corresponding buttons on the remote control
and on the projector.
1
Power
Auto
Source Freeze
Blank
3 2 5
6
READY
KEYSTONE
Menu
4
POWER
POWER
Enter
6
5
4
1
2
3
Volume
VOL -
VOL +
Mute Keystone
MENU
1
2
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Setting the OSD Language
You may want to reference the OSD on your projector while reading this section. Set the OSD language to your preference before continuing. (The default language is English.)
1. Press the Menu button. The Main menu appears.
2. Press
3. Press
until Language is highlighted.
until the language you want is highlighted.
4. Press the Enter button to select the language.
5. Press the Menu button twice to close the OSD.
– 18 –
Downloaded From projector-manual.com Boxlight Manuals
O
Onn--SSccrreeeenn D
Diissppllaayy M
Meennuu SSeettttiinnggss
Main Menu
to move to the Main menu.
Press the Menu button to open the OSD menu. If necessary, press
to change values for settings, and
to move up and down in the Main menu. Press
Press
then press Enter to confirm the new setting.
ITEM
DESCRIPTION
DEFAULT
Brightness
Press
to adjust the brightness. (Range: 0—100)
50
Contrast
Press
to adjust the contrast. (Range: 0—100)
50
Sharpness
Press
to adjust the display sharpness (Range: 1-5)
3
Color
Temperature
Press
to adjust the video tint/hue.
(Range: Cool/Normal/Warm)
Color
Saturation
Press
to adjust the video saturation. (Range: 0—100)
Color Tint
Press
to adjust the video tint/hue. (Range: 0—100)
Gamma
Press
to adjust the gamma correction of the display.
Input
Gamma
Brightness
PC
MAC
Video
Chart
B&W
2.2
1.8
2.4
2.2
2.4
High
High
Low
Low
High
Color Space
to adjust the color space.
Press
(Range: Auto—RGB—YpbPr—YCbCr)
Reset
Resets all Main items settings except Color Saturation to default values
– 19 –
Downloaded From projector-manual.com Boxlight Manuals
Normal
50
50
PC
Auto
-
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Main Menu Items Supported for Each Input Source
Depending on the video source not all items in the OSD are available. Items that are available for
each input source are marked with “X”. Items that are not available can not be selected in the OSD.
Function
RGB
DVI
Component Video
Brightness
X
X
X
X
X
Contrast
X
X
X
X
X
Sharpness
X
X
X
X
X
Color Temperature
X
X
X
X
X
Color Saturation
X
X
X
X
X
X
X
X
X
Color Tint
Gamma
X
X
X
– 20 –
Downloaded From projector-manual.com Boxlight Manuals
Composite Video
S-Video
O
Onn--SSccrreeeenn D
Diissppllaayy M
Meennuu SSeettttiinnggss
Setup Menu
to move to the Setup menu. Press
to
Press the Menu button to open the OSD menu. Press
to change values for settings, and then press Enmove up and down in the Setup menu. Press
ter to confirm the new setting.
ITEM
DESCRIPTION
DEFAULT
Horizontal
Position
Press
to move the image left or right. (Range: 0—100)
50
Vertical
Position
Press
to move the image up or down. (Range: 0—100)
50
Keystone
Press
to correct distortion of the projected image.
(Range: -50—50)
Aspect Ratio
Press
to toggle between the 4:3 standard format and 16:9 High Definition
TV (HDTV) format.
Reset
Resets Keystone and Aspect Ratio to default values
0
4:3
Setup Menu Items Supported for Each Input Source
Depending on the video source not all items in the OSD are available. Items that are available for
each input source are marked with “X”. Items that are not available can not be selected in the OSD.
Function
RGB
Horizontal Position
X
Vertical Position
X
Keystone
X
DVI
Component Video
X
X
– 21 –
Downloaded From projector-manual.com Boxlight Manuals
Composite Video
X
S-Video
X
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Config Menu
to move to the Config menu. Press
to
Press the Menu button to open the OSD menu. Press
to change values for settings, and then press Enmove up and down in the Config menu. Press
ter to confirm the new setting.
ITEM
DESCRIPTION
DEFAULT
Blank Screen
to select a background color for blank screen
Press
(Range: Black – Red—Green—Blue—White)
Auto Source
Press
to enable or disable automatic source detection
(Range: On—Off)
On
Auto Power
Off
Press
to enable or disable automatic shut-down of lamp after 10 minutes of inactivity (Range: On—Off)
Off
Volume
Menu
Position
Press
Menu Display
Translucent
Menu
to determine the timeout delay of the OSD
Press
(Range: 10 - 20 sec.)
Press
to set menu screen translucency
(Range: On—Off)
Reset
Resets all Config screen items to default values
to adjust the audio volume level (Range: 0 - 10)
Press
to position the OSD on screen
(Range: Left—Right—Center—Down—Up)
– 22 –
Downloaded From projector-manual.com Boxlight Manuals
Blue
5
Center
15
Off
O
Onn--SSccrreeeenn D
Diissppllaayy M
Meennuu SSeettttiinnggss
Utility Menu
to move to the Utility menu. Press
to
Press the Menu button to open the OSD menu. Press
to change values for settings, and then press Enmove up and down in the Utility menu. Press
ter to confirm the new setting.
ITEM
DESCRIPTION
Video Type
to select the video standard.
Press
(Range: Auto—NTSC—PAL—SECAM)
Video AGC
Press
to enable or disable automatic gain control
for the video source. (Range: On—Off)
Projection
Press
DEFAULT
Auto
On
to choose from four projection methods:
Desktop mount, front of screen
Desktop front
Desktop mount, rear of screen
Ceiling mount, front of screen
Ceiling mount, rear of screen
Frequency
Press
to adjust the A/D sampling clock.
(Range: 0—180)
Auto detected
Tracking
Press
to adjust the A/D sampling number.
(Range: 0—100)
Auto detected
Reset
Resets Video Type, Video AGC, and Projection to default values
– 23 –
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Language Menu
Press the Menu button to open the OSD menu. Press
to move up and down in the Language menu.
ITEM
to move to the Language menu. Press
DESCRIPTION
DEFAULT
English
French
German
Italian
Spanish
Press the cursor
menu.
button to move up and down in the
English
Swedish
Chinese Simplified
Press the Enter button to select the language.
Chinese Traditional
Japanese
Korean
– 24 –
Downloaded From projector-manual.com Boxlight Manuals
O
Onn--SSccrreeeenn D
Diissppllaayy M
Meennuu SSeettttiinnggss
Status Menu
to move to the Status menu. Press
to
Press the Menu button to open the OSD menu. Press
to change values for settings, and then press Enmove up and down in the Status menu. Press
ter to confirm the new setting.
ITEM
DESCRIPTION
DEFAULT
Video
Information
Displays the resolution and refresh rate of the connected video device.
Active Source
Displays the active source.
Software
Version
Information about the firmware version.
Lamp Hours
Number of hours lamp has been in Normal use and number of hours lamp
has been in Eco use.
Lamp Mode
Toggles between lamp modes. ECO mode uses less power but decreases
the lamp brightness.
2000
lumens
Lamp Hour
Reset
After replacing the lamp, this item should be reset. Refer to “Replacing the
Projection Lamp” on page 26.
—
– 25 –
Downloaded From projector-manual.com Boxlight Manuals
These
items are
display
only.
MAINTENANCE AND SECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer.
Important:
1. The lamp contains a certain amount of mercury and should be disposed of according to local ordinance regulations.
2. Avoid touching the glass surface of the new lamp: Doing so may shorten its operation life.
Warning:
1. Be sure to turn off and unplug the projector at least an hour before replacing the lamp. Failure to
do so could result in a severe burn.
2. It is recommended that you do not attempt to replace the lamp while the projector is installed on
a ceiling. If you do attempt this, wear protective goggles to prevent glass from a ruptured lamp getting into your eyes.
1.
2.
3.
Lift the screw cover (A).
Remove the screw on
the lamp compartment
cover (B) and then lift
the lamp compartment
cover (C).
Remove the two screws
from the lamp module
(A) and then lift the
module handle up (B).
Pull up firmly to remove
the lamp module.
Downloaded From projector-manual.com Boxlight Manuals
M
Maaiinntteennaannccee aanndd SSeeccuurriittyy
4.
Reverse Steps 1 to 4 to
install the new lamp
module.
Note: The lamp module
should be oriented as
shown here when replacing.
Resetting the Lamp
After replacing the lamp, reset the lamp hour counter to zero. Refer to the following:
1.
2.
3.
4.
5.
Press the Menu button to open the
Main menu.
button to move
Press the cursor
to the Status menu.
Press the cursor
button to move
to Lamp Hour Reset.
Press the Enter button.
A message screen appears.
Press the cursor buttons in this order:
; ; ; .
The “Lamp Hour Reset OK !!” message appears. Then the Status menu
appears again showing the Lamp
Hours reset to zero.
Lamp Hour Reset OK !!
– 27 –
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least an hour before cleaning. Failure to do so
could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings
on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated
room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
– 28 –
Downloaded From projector-manual.com Boxlight Manuals
M
Maaiinntteennaannccee aanndd SSeeccuurriittyy
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and wipe the
case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
Using the Kensington Lock
If you are concerned about security, attach the projector to a permanent object with the Kensington
slot and a security cable.
Note:
Contact your vendor for details on purchasing a suitable Kensington security cable.
– 29 –
Downloaded From projector-manual.com Boxlight Manuals
TROUBLESHOOTING
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose
connection. Check the following before proceeding to the problem-specific solutions.
•
Use some other electrical device to confirm that the electrical outlet is working.
•
Ensure the projector is turned on.
•
Ensure all connections are securely attached.
•
Ensure the attached device is turned on.
•
Ensure a connected PC is not in suspend mode.
•
Ensure a connected notebook computer is configured for an external display. (This is usually done by pressing an Fn-key combination on the notebook.)
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the
problem more quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go
to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.
Downloaded From projector-manual.com Boxlight Manuals
TTrroouubblleesshhoooottiinngg
LED Error Messages
LED
Power
STATUS/
NUMBER OF
FLASHES
Flashing
DESCRIPTION
REMEDY
Lamp not ready
Do not press the power button.
3
System overheated
Allow the projector to cool down.
4
System interface error
Contact your dealer for assistance.
5
Lamp error
Replace the lamp module.
6
Fan error
Refer to Ready LED status in this
table to determine which fan.
7
Lamp cover open
Close the lamp cover.
8
DLP driver error
9
Color wheel error
Contact your dealer for assistance.
Ready
Flashing
Valid only when fan error indicated by Power LED flashing 6 times.
1
Power fan
2
Blower fan
3
Lamp fan or Optical fan
Contact your dealer for assistance.
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the 8-meter (26-feet) specified range.
4. Check that the projector lens is clean.
5. Make sure the output resolution from the PC is 800 x 600 (SVGA model) or 1024 x 768
(XGA model), the native resolution of the projector.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.
Problem: The image is reversed or upside down
1. Check the Projection setting on the Utility menu of the OSD.
Problem: The image is streaked
– 31 –
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
1. Set the Frequency and Tracking settings on the Utility menu of the OSD to the default
settings.
2. To ensure the problem is not caused by a connected PC’s video card, connect to another
computer.
Problem: The image is flat with no contrast
1. Adjust the Contrast setting on the Main menu of the OSD.
Problem: The color of the projected image does not match the source image.
1. Adjust the Color Temperature and Gamma settings on the Main menu of the OSD.
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Press the power button twice to turn off the
projector. When the Lamp Ready LED is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards the remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity of the remote control.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
Audio Problems
Problem: There is no sound
1. Adjust the projector volume.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
– 32 –
Downloaded From projector-manual.com Boxlight Manuals
TTrroouubblleesshhoooottiinngg
Having the Projector Serviced
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in
the original carton. Include a description of the problem and a checklist of the steps you took when
trying to fix the problem. The information may be useful to the service personnel. Return the projector
to the place you purchased it.
– 33 –
Downloaded From projector-manual.com Boxlight Manuals
SPECIFICATIONS
Specifications
XGA
SVGA
Power consumption
< 350 watts
< 280 watts
< 350 watts
< 280 watts
Lamp
250W
200W
250W
200W
(ECO mode 200W)
(ECO mode 160W)
(ECO mode 200W)
(ECO mode 160W)
Display type
TI DMD 0.7-inch, 12 deg. DDR
TI DMD 0.55-inch, 12 deg. DDR
Resolution
XGA 1024 x 768 native
SVGA 800 x 600 native
Bandwidth
Up to SXGA 1280 x 1024 @ 60 Hz
Up to XGA 1024x 768 @ 60 Hz
Color
16.7 Million (24-bits/pixel)
Weight
3.55 kg (7.8 lbs)
Projection distance
1.5 to 8 meter (4.9 to 26 feet)
Projection screen size
0.94 to 6.1 meter (37 inches to 240 inches)
Projection lens
Manual zoom and focus
Zoom ratio
1.2:1
Vertical keystone correction
+ / - 15
Projection methods
Desktop front/rear; ceiling front/rear
Data Compatibility
IBM PC or compatibles (VGA, SVGA), Mac
HDTV
Video
Video compatibility
NTSC/NTSC 4.43, PAL (B/G/H/I/M/N 60), SECAM
H-Sync
15,31 - 70 kHz
V-Sync
50 - 85 Hz
Safety certification
FCC Class B, UL, CUL, CE, CB, TUV-GS, CCC
Operation temperature
10° ~ 35°
Dimensions
32.8 x 23.8 x 8.8 cm (12.9 x 9.4 x 3.5 inches)
Standby
< 20 watts
Noise
36 dB typical
Audio speaker
2W mono speaker
Uniformity
80 %
Downloaded From projector-manual.com Boxlight Manuals
SSppeecciiffiiccaattiioonnss
Input/output connectors
PC
DVI-I
RGB in
RGB out
USB
Video
Composite video (RCAx1)
S-Video (Mini-DIN)
Component video Y,Pb/Cb,Pr/Cr (RCAx3)
Audio
Mini-jack in
Mini-jack out
Right and left in (RCAx2)
Service/upgrades
RS-232
Security
Kensington slot
– 35 –
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Projection Distance versus Projection Size
C
D
A
B
L Projection Distance
Projection
Distance
Max. Screen Size
Min. Screen Size
Diagonal
Width
Diagonal
Width
A
C
1.5m
1.14m
0.91m
B
D
0.68m
0.94m
0.75m
0.56m
4.92'
45"
36"
27"
36.88"
29.5"
22.1"
2m
1.52m
1.22m
0.91m
1.25m
1m
0.75m
6.56'
60"
48"
36"
49.18"
39.34"
29.51"
2.4m
1.83m
1.46m
1.1m
1.5m
1.20m
0.90m
7.87'
72"
57.6"
43.2"
59"
47.2"
35.4"
2.8m
2.13m
1.71m
1.28m
1.75m
1.4m
1.05m
9.18'
84"
67.2"
50.4"
68.85"
55.08"
41.31"
3.2m
2.44m
1.95m
1.46m
2m
1.6m
1.20m
10.5'
86"
68.8"
51.6"
70.49"
56.39"
42.29"
3.6m
2.74m
2.19m
1.65m
2.25m
1.80m
1.35m
11.81'
108"
86.4"
64.8"
88.52"
70.82"
53.11"
4m
3.05m
2.44m
1.83m
2.5m
2.00m
1.50m
13.12'
120"
96"
72"
98.36"
78.69"
59.02"
4.4m
3.35m
2.68m
2.01m
2.75m
2.2m
1.65m
14.43'
132"
105.6"
79.2"
108.19"
86.55"
64.91"
4.8m
3.66m
2.93m
2.19m
3.00m
2.40m
1.80m
15.74'
144"
115.2"
86.4"
118.03"
94.42"
70.82"
5.2m
3.96m
3.17m
2.38m
3.25m
2.60m
1.95m
17.06'
156"
124.8"
93.6"
127.86"
102.29"
76.72"
5.6m
4.27m
3.41m
2.56m
3.50m
2.80m
2.10m
18.37'
168"
134.4"
100.8"
137.7"
110.16"
82.62"
6m
4.57m
3.66m
2.74m
3.75m
3.00m
2.25m
19.68'
180"
144"
108"
147.54"
118.03"
88.52"
8m
6.10m
4.88m
3.66m
5.00m
4.00m
3.00m
26.24'
240"
192"
144"
196.72"
157.38"
118.03"
L
Height
– 36 –
Downloaded From projector-manual.com Boxlight Manuals
Height
SSppeecciiffiiccaattiioonnss
Timing Mode Table
The native resolution is 800 x 600 for the SVGA series and 1024 x 768 for the XGA series. Resolution other than native mode may display with uneven size of text or lines.
The following table shows the supported timing modes.
Signal
Resolution
Frequency H. Frequency V.
( KHz )
( Hz )
Video
Digital
Analog
NTSC
--
15.734
60.0
Ο
--
--
PAL / SECAM
--
15.625
50.0
Ο
--
--
640 x 350
37.9
85.1
--
Ο
Ο
720 x 400
31.5
70.0
--
Ο
Ο
720 x 400
37.9
85.0
--
Ο
Ο
640 x 480
31.5
60.0
--
Ο
Ο
640 x 480
37.9
72.8
--
Ο
Ο
640 x 480
37.5
75.0
--
Ο
Ο
640 x 480
43.3
85.0
--
Ο
Ο
800 x 600
37.9
60.3
--
Ο
Ο
800 x 600
46.9
75.0
--
Ο
Ο
800 x 600
48.1
72.2
--
Ο
Ο
800 x 600
53.7
85.1
--
Ο
Ο
1024 x 768
48.4
60.0
--
Ο
Ο
1024 x 768
56.5
70.1
--
Ο
Ο
1024 x 768
60.0
75.0
--
Ο
Ο
1024 x 768
68.7
85.0
--
Ο
Ο
1280 x 1024
64.0
60.0
--
Ο
Ο
640 x 480
35.0
66.7
--
Ο
Ο
832 x 624
49.7
74.5
--
Ο
Ο
1024 x 768
60.2
74.9
--
Ο
Ο
1152 x 870
68.7
75.1
--
Ο
Ο
1920 x 1080
33.8
60.0
Ο
--
--
1920 x 1080
28.1
50.0
Ο
--
--
1280 x 720
45.0
60.0
Ο
--
--
720 x 576
31.3
50.0
Ο
--
--
720 x 480
31.5
60.0
Ο
--
--
VESA
Apple Macintosh
HDTV
SDTV
Ο
Frequency supported
--
Frequency not supported
For XGA series only
– 37 –
Downloaded From projector-manual.com Boxlight Manuals
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr M
Maannuuaall
Dimensions
32.8 cm (12.9 inches)
8.8 cm (3.5 inches)
23.8 cm (9.4 inches)
– 38 –
Downloaded From projector-manual.com Boxlight Manuals
REGULATORY COMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
UL, CUL, CB, TUV-GS, CCC
EN 55022 Warning
This is a Class B product. In a domestic environment, it may cause radio interference, in which case
the user may be required to take adequate measures. The typical use is in a conference room, meeting room, or auditorium.
Downloaded From projector-manual.com Boxlight Manuals
Download PDF