- Computers & electronics
- Audio & home theatre
- Supplementary music equipment
- Runco
- XP-103DHD
- Specification
advertisement
▼
Scroll to page 2
of 94
I NSTALLATION/ O PERATION M ANUAL Vistage™ Series Ultra-Thin Flat-Panel Displays Models V-50HD and V-63HD Downloaded From TV-Manual.com Manuals Downloaded From TV-Manual.com Manuals RuncoCare™ Standard Two Year Limited Warranty Congratulations on your purchase of a Runco® product! With proper installation, setup and care, you should enjoy many years of unparalleled video performance. Y This RuncoCare Standard Limited Warranty is provided free of charge by Runco International, LLC (“Runco”) with the purchase of a covered Runco product. The following sets forth Runco’s Standard Limited Warranty applicable to all Runco projectors, processors, LCD display and plasma display products, with the exception of the following models: XP-103DHD, SC-1, SC-1a, CW-95DHD and VW-100HD1. EL IM IN A R The following terms and conditions of the RuncoCare Standard Limited Warranty represent a contract between us, Runco, and you, the customer, who has purchased a Runco product. This contract applies to purchases of covered Runco products occurring on or after February 11, 2010. Runco reserves the right to change the terms of this contract, and such changes shall apply to purchases of covered Runco products that occur on or after any future effective date. RuncoCare Standard Features • Two-year protection from defects in material and workmanship • Access to 24x7 phone support • Complimentary, second-day one-way shipping Warranty Coverage PR Runco warrants its products to be free from defects in material and workmanship during the warranty period provided below. If, in Runco’s sole determination, a product proves to be defective in material or workmanship during the warranty period, Runco will repair the product, replace the product with a substantially similar new or like-new product, or refund a prorata share of the purchase price (calculated based on the remainder of the warranty period and the then-current MSRP2 of a similar product), if repair or replacement of the product is determined by Runco to not be feasible. Runco has sole discretion in determining whether a same or like model is offered, and what constitutes a “substantially similar model.” Length of Warranty Runco products are warranted for two (2) years from the date of shipment from Runco. Lamps are warranted six (6) months from the date of shipment or 1000 hours of use, whichever comes first. All other accessories, which include but are not limited to, cables, remotes, carrying cases, lens cap and other peripherals sold with the Runco product, are warranted for ninety (90) days from the date of the original shipment of the accessory. Eligibility This RuncoCare Standard Limited Warranty is valid only for the first customer who purchases the covered product from an authorized Runco dealer or distributor. This warranty is not transferable. You may be required to provide proof of purchase in order to receive warranty services. 1. Runco may update this list of products excluded from this warranty from time to time at Runco’s sole discretion, but updates to the list of covered products will not apply on a retroactive basis. 2. MSRP is defined as the most recent product price listed on Runco’s price list. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals iii RuncoCare Claim Procedure In the event of a product defect, please follow the warranty claim procedure provided below: 1. The Customer is required to contact a Runco dealer or Runco Technical Support via email at [email protected] or via phone at (toll free) (800) 23RUNCO (800-237-8626). If the customer is located outside North America, call +3589 4200 554 in Europe for product service. 2. Be prepared to provide the date of purchase, the place of purchase, serial number, product model number, description of the problem and troubleshooting steps already attempted. EL IM IN A R Y 3. Runco Technical Support staff will attempt to correct any minor issues that may be causing the problem. If Runco is unable to resolve the problem through troubleshooting, a Return Material Authorization (RMA) number will be issued for the exchange of the defective product if it is determined that the claim was made within the coverage period of the Standard Limited Warranty. 4. If it is determined that the Standard Limited Warranty applies to the claim, the customer will need to return the defective product to the Runco repair depot location specified by the Runco technical support representative. The customer will need to properly package the defective product, consisting of the product only, and not include any accessories (e.g., cables, remotes, carrying cases, lens, lens cap and other peripherals) and return it to the Runco repair depot specified by the technical support representative. It is the customer’s responsibility to properly package the hardware, include all appropriate materials, and return it to the location specified by the Runco technical support department. The customer will need to address and resolve any shipping damage claims directly with the shipping company. 5. The customer is responsible for providing a suitable box to ship the defective product to an authorized Runco repair depot. Boxes may be purchased from a Runco technical support representative. 6. The customer is responsible for paying freight charges to ship the defective product to an authorized Runco repair depot. 7. For in-warranty repairs, Runco will pay freight charges to return the repaired/replacement product (which shall not include accessories--e.g., cables, remotes, carrying cases, lens cap and other peripherals sold with the Runco product) to the customer from the Runco repair depot. PR 8. Once an RMA has been created, the customer may contact [email protected] for followup questions or confirmation status of the claim process. Warranty Exclusions This RuncoCare Standard Limited Warranty does not include or is limited by the following: 1. Products not purchased from an authorized Runco dealer 2. Rental costs incurred by the customer in the event of product defect or failure 3. Any product with a defaced, modified, or removed serial number 4. Damage, deterioration, or malfunction resulting from: a Accident, abuse, misuse, neglect, improper ventilation, fire, water, disaster, lightning, or other acts of nature, smoke exposure (cigarette or otherwise), unauthorized product modification (including use of an unauthorized mount), or failure to follow instructions supplied with the product b Repair or attempted repair by anyone not authorized by Runco c Any damage to the product due to shipment d Removal or installation of the product e Causes external to the product, such as electric power fluctuations or failure f Use of supplies or parts (including lamps) that are not purchased from Runco or do not meet Runco’s specifications g Normal wear and tear iv Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual h Expected lamp degradation and normal decrease in lamp output over a period of time or as the lamp is consumed i Customer caused defects, including but not limited to, scratched/defaced/altered plastics j Failure to follow maintenance procedures as outlined in the product’s user guide where a schedule is specified for regular cleaning of the product k Opening the product and/or tampering with internal circuitry l Products lost, stolen or discarded m Any damage or dissatisfaction associated with latent images, “burnin,” or any other damage determined by Runco to be the result of customer use patterns n Any other cause, which does not relate to a product defect in material or workmanship Y 5. Removal, installation, and setup service charges are excluded from this Standard Limited warranty EL IM IN A R 6. Black uniformity issues or other LCD issues associated with usage outside the Runco recommended guidelines and specifications for the product 7. Bright or dark sub pixels that are characteristic of LCD technology and considered by Runco to be acceptable and within Runco’s manufacturing specifications. (See “Sub Pixel Policy,” below.) 8. Second day shipment delivery time and availability may vary based on origin and destination and Runco is unable to deliver to PO Box and FPO Box addresses Sub Pixel Policy PR It is not uncommon for one or more sub pixels to become bright or dark during or after the manufacturing process. A bright sub pixel is one that remains in the on position, and a dark sub pixel is one that appears black or off. The sub pixels are usually hard to see and will not detract from the display quality or usability at normal viewing distance. The following are Runco’s criteria for identifying bright or dark sub pixels that would be considered unacceptable: a) the number of bright or dark sub pixels; b) the location of the bright or dark sub pixels; c) the color of the bright sub pixels; and d) the Runco model size. If sub pixels have been identified as unacceptable by Runco the LCD will be deemed faulty and will be replaced if reported within the warranty period. If there are issues with bright or dark sub pixels, gather the information listed above and call or email [email protected]. Other Terms and Conditions 1. Runco will not accept returned Product unless an RMA number has been issued by Runco. 2. If an Advance Exchange return occurs, it is the customer’s responsibility to properly package the defective product and ship it to the address provided by the Runco technical support representative with the RMA number prominently displayed. If the defective product is not properly packaged and is damaged in transit during its return to Runco, you may be invoiced for either the repair costs, if repairable, or the MSRP of a replacement product and shipping costs incurred by Runco. 3. The repaired or replaced product will assume the remainder of your original product’s RuncoCare Service Plan term or 90 days from the date the repaired unit is shipped, whichever is longer. 4. If a replacement product is sent, the customer agrees to retain the replacement for the product you purchased and your defective product becomes the property of Runco. Extended Service Options Runco offers extended and expanded service plans. For information on additional product protection, please email [email protected] or call (toll free) (800) 23RUNCO (800-237-8626). Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals v Online Product Registration Please visit http://www.runco.com/support/product-registration/ to register product. Limitation of Implied Warranties Y RUNCO PROVIDES NO WARRANTIES, EXPRESS OR IMPLIED, EXCEPT THOSE EXPRESSLY PROVIDED HEREIN. RUNCO EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. EL IM IN A R Exclusion of Damages RUNCO’S MAXIMUM AGGREGATE LIABILITY HEREUNDER IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. 1. RUNCO SHALL NOT BE LIABLE FOR DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF THE CUSTOMER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 2. RUNCO SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES. 3. RUNCO SHALL NOT BE LIABLE FOR ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY. Effect of Local Law PR This warranty gives you specific legal rights, and you may have other rights, which vary from locality to locality. Some localities do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you. COPYRIGHT AND TRADEMARKS: © Copyright 2011 Runco International, LLC (“Runco”). This document contains proprietary information protected by copyright, trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of Runco. The trademarks reproduced in this Runco Owner’s Manual and used on the Runco Products are either owned by Runco or are licensed by Runco. You may not reproduce or use the trademarks without the prior written consent of Runco. Runco Products are manufactured under one or more of the following patents: US. Patent 6755540 and Other Patents Pending. vi Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Important Safety Instructions Thank you for your purchase of this quality Runco video product! For the best performance, please read this manual carefully as it is your guide through the menus and operation. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. EL IM IN A R CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Y CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. PR 9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus. 11. Only use the attachments/accessories specified by the manufacturer. 12. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Keep the packing material in case the equipment should ever need to be shipped. 16. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals vii Compliance Information DECLARATION OF CONFORMITY: Manufacturer’s Name: Runco International, LLC Manufacturer’s Address: 1195 NW Compton Drive, Beaverton, OR 97006-1992 hereby declares that the Products’ Model Numbers: EL IM IN A R conform with the provisions of: Y V-50HD and V-63HD Council Directive 2004/108/EC on Electromagnetic Compatibility; EN 55022 “Limits and methods of measurements of radio interference characteristics of information technology equipment” 1998; EN 55024 “Limits and methods of measurements of immunity characteristics of information technology equipment” 1998; Including: • EN 61000-4-2 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 2: Electrostatic discharge immunity test” • EN 61000-4-3 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 3: Radiated, Radio-Frequency, Electromagnetic Field Immunity Test” • EN 61000-4-4 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 4: Electrical fast transient/burst immunity test” PR • EN 61000-4-5 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 5: Surge immunity test" • EN 61000-4-6 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 6: Conducted disturbances induced by radio-frequency fields immunity test" • EN 61000-4-8 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 8: Conducted disturbances induced by power frequency magnetic fields immunity test" • EN 61000-4-11 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 11: Voltage dips, short interruptions and voltage variations immunity tests" And: • EN 61000-3-2 "Electromagnetic compatibility (EMC) Part 3, Section 2: Limits for harmonic current emissions (equipment input current up to and including 16 A per phase)" 2000; • EN 61000-3-3 "Electromagnetic compatibility (EMC) Part 3, Section 3: Limitations of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current up to and including 16 A and not subject to conditional connection" 1995; Council Directive 2006/95/EC and amended by M1 and C1 on Low Voltage Equipment Safety; EN 60950 “Safety of information technology equipment, including electrical business equipment” The Technical Construction file required by this Directive is maintained at the corporate headquarters of Runco International, LLC, located at 1195 NW Compton Drive, Beaverton, OR 97006-1992. Date of Declaration: April 2011 viii Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual FCC PART 15: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. • Reorient or relocate the receiving antenna. EL IM IN A R • Increase the separation between the equipment and receiver. Y This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA (ICES-003): This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. PRODUCT DISPOSAL: PR The Product contains small amounts of tin, lead and/or mercury. Disposal of these materials may be regulated due to environmental considerations. IMPORTANT RECYCLE INSTRUCTIONS Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG. DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT (Applicable throughout the European Union and other European countries with separate collection programs) This symbol found on your product or on its packaging, indicates that this product should not be treated as household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate disposal of this product. The recycling of materials will help to conserve natural resources. This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals ix PR EL IM IN A R Y Notes: x Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual 1 Table of Contents RuncoCare™ Standard Two Year Limited Warranty ................................................... iii Important Safety Instructions ....................................................................................... vii Compliance Information .............................................................................................. viii 1. Introduction ...............................................................................................................1 Y About This Manual .......................................................................................................1 EL IM IN A R Target Audience .....................................................................................................1 If You Have Comments About This Manual... ..........................................................1 Textual and Graphic Conventions ...........................................................................1 Using This Manual ........................................................................................................2 Description, Features and Benefits ...............................................................................3 Key Features and Benefits ......................................................................................4 Parts List ................................................................................................................4 2. Controls and Functions ............................................................................................5 Vistage Series at a Glance ............................................................................................5 Front-Panel Controls and Indicators........................................................................5 Rear-Panel Connectors...........................................................................................6 PR DHD Controller Front Panel ..........................................................................................7 DHD Controller Rear Panel ...........................................................................................8 V-50HD/V-63HD Remote Control Unit .........................................................................9 3. Installation ...............................................................................................................13 Remote Control ..........................................................................................................13 Notes on Batteries ................................................................................................13 Notes on Remote Control Operation .....................................................................14 Quick Setup ...............................................................................................................14 Installation Considerations ..........................................................................................15 Mounting the V-50HD/V-63HD on a Wall or Table Stand ......................................15 Audio/Video Synchronization Issues......................................................................15 Ventilation .............................................................................................................16 Ambient Light .......................................................................................................16 Other Considerations ............................................................................................16 Rack-Mounting the DHD Controller.......................................................................16 Connections to the V-50HD/V-63HD and DHD Controller ..........................................17 Connecting the DHD Controller to the V-50HD/V-63HD........................................17 Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals xi Table of Contents Connecting Source Components to the DHD Controller .......................................18 Connecting an Audio Processor or Secondary Display Device to the DHD Controller (Optional)............................................................................22 RS-232 Controller Connection ..............................................................................23 Ethernet Network Connection ...............................................................................23 Connecting to AC Power ......................................................................................24 Turning on the Power .................................................................................................24 4. Operation .................................................................................................................25 Y Setting the Computer Display Properties ....................................................................25 Using the On-Screen Menus ......................................................................................27 EL IM IN A R Main Menu............................................................................................................29 Input Source .........................................................................................................29 Aspect Ratio .........................................................................................................29 Screen..................................................................................................................32 Picture ..................................................................................................................32 Input Position........................................................................................................36 Memory Presets ..................................................................................................38 Sleep Timer ..........................................................................................................39 Information ...........................................................................................................40 Calibration ............................................................................................................41 Service .................................................................................................................47 PR 5. Maintenance and Troubleshooting ........................................................................57 Troubleshooting Tips ..................................................................................................57 6. External Control ......................................................................................................59 Serial Communications ...............................................................................................59 RS-232 Connection and Port Configuration ..........................................................59 Serial Command Syntax .......................................................................................59 Using Discrete IR Codes ............................................................................................64 IR Command Protocol ..........................................................................................64 IR Command List..................................................................................................66 Using HDMI CEC Messages .......................................................................................68 CEC Command List..............................................................................................68 7. Specifications ..........................................................................................................71 V-50HD/V-63HD Specifications ..................................................................................71 DHD Controller Specifications ....................................................................................72 V-50HD Dimensions ...................................................................................................73 V-63HD Dimensions ...................................................................................................74 Supported Timings .....................................................................................................75 xii Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual 1 List of Figures 2-1. V-50HD Front-Panel Controls and Indicators ................................................................5 2-2. V-63HD Front-Panel Controls and Indicators ................................................................5 2-3. V-50HD/V-63HD Rear Panel ........................................................................................6 2-4. DHD Controller Front Panel ..........................................................................................7 Y 2-5. DHD Controller Rear Panel ...........................................................................................8 EL IM IN A R 2-6. DHD Controller/V-50HD/V-63HD Remote Control ........................................................9 3-1. Ventilation Requirements for Enclosure Mounting .......................................................16 3-2. Connecting the V-50HD/V-63HD to the DHD Controller .............................................17 3-3. HDMI Source Connections .........................................................................................18 3-4. Component Video Source Connections......................................................................19 3-5. RGBHV Source Connections......................................................................................20 3-6. SCART RGBS Source Connection .............................................................................21 3-7. Composite Video Source Connections .......................................................................21 3-8. Audio Processor Connection to DHD Controller .........................................................22 3-9. RS-232 Control System Connection...........................................................................23 3-10. Ethernet Network Connection to Primary DHD Controller .........................................23 4-1. V-50HD/V-63HD OSD Menu Structure .......................................................................27 PR 4-2. Typical PLUGE Pattern for Adjusting Brightness .........................................................32 4-3. Typical Gray Bar Pattern for Adjusting Contrast ..........................................................33 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint................................34 4-5. Typical Test Pattern for Adjusting Sharpness..............................................................36 4-6. Overscan Modes ........................................................................................................37 4-7. CIE 1931 Chromaticity Diagram .................................................................................42 4-8. Keystone and Pincushion Distortion ...........................................................................45 4-9. Image Alignment Controls ..........................................................................................46 6-1. RC5 Message Format ................................................................................................65 7-1. V-50HD Dimensions (with Optional Speaker Bar)........................................................73 7-2. V-63HD Dimensions (with Optional Speaker Bar)........................................................74 Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals xiii List of Figures PR EL IM IN A R Y Notes: xiv Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Introduction 1. Introduction This Owner’s Manual describes how to install, set up and operate the Runco Vistage™ Series Flat Panel Display and DHD Controller. 1.1 About This Manual Throughout this manual, the Runco Vistage™ Series Flat Panel Display and DHD Controller is referred to as the “V-50HD/V-63HD.” Target Audience Y Runco has prepared this manual to help installation personnel and end users get the most out of the V-50HD/V-63HD. EL IM IN A R Runco has made every effort to ensure that this manual is accurate as of the date it was printed. However, because of ongoing product improvements and customer feedback, it may require updating from time to time. You can always find the latest version of this and other Runco product manuals on-line, at www.Runco.com. Runco welcomes your comments about this manual. Send them to [email protected]. If You Have Comments About This Manual... Text Conventions: The following conventions are used in this manual, in order to clarify the information and instructions provided: Textual and Graphic Conventions • Remote control unit button identifiers are set in upper-case bold type; for example, “Press EXIT to return to the previous menu.” • Computer input (commands you type) and output (responses that appear on-screen) is shown in monospace (fixed-width) type; for example: “To change the aspect ratio to Letterbox, type LETTERBOX <Enter>.” PR • All keys with functional names are initial-capped, set in bold type and enclosed in angle brackets. These keys are the following: <Enter>, <Spacebar>, <Control>, <Esc> and <Tab>. • <Enter> indicates that you may press either the RETURN or ENTER key on your keyboard if it has both keys. In addition to these conventions, underlining, boldface and/or italics are occasionally used to highlight important information, as in this example: Note A carriage return must be used after each command or string. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 1 Introduction Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury: Note NOTES emphasize text with unusual importance or special significance. They also provide supplemental information. Caution CAUTIONS alert users that a given action or omitted action can degrade performance or cause a malfunction. Y TIPS highlight time-saving short cuts and helpful guidelines for using certain features. EL IM IN A R 1.2 Using This Manual Tip WARNING WARNINGS appear when a given action or omitted action can result in damage to the equipment, or possible non-fatal injury to the user. DANGER! DANGER appears when a given action can cause severe injury or death. Use the following table to locate the specific information you need in this manual. PR If you need... Information about obtaining service iv General information about the Vistage™ Series Flat Panel Display and DHD Controller 3 Installation instructions 13 First-time configuration instructions 25 Advanced configuration instructions 41 Troubleshooting tips 57 Specifications for the Vistage™ Series Flat Panel Display and DHD Controller 71 2 Downloaded From TV-Manual.com Manuals ... Turn to page: Vistage™ Series Flat-Panel Display Installation/Operation Manual Introduction Runco introduces its Vistage™ Series of ultra-thin flat panel displays, combining elegance, beauty and unparalleled customization with the stellar video performance that is synonymous with the Runco brand. These flat panel displays offer a stylish solution that can be personalized to reflect the style and passion of its homeowner. Unlike most other thin panel televisions, the entire front of the Vistage display is comprised of solid glass, creating a better viewing performance when the display is on and a more uniform finish when it is off. Beyond its sheer beauty, the glass front improves optical performance of the flat panel, because there are no surface uniformity issues common to the acrylic or plastic surfaces used on most televisions. EL IM IN A R Y The Vistage Series utilizes the latest in display technology, including Runco’s Emissive Cell Structure™, which delivers exceptional brightness and viewing angles. Using a proprietary algorithm, each sub-pixel is individually modulated to turn on or off based on the content being played, creating exceptional contrast and black levels previously unachieved in the industry. The Emissive Cell Structure performs best in light-controlled environments and offers amazing black levels and dark-content performance. Because the light sources turn off for black content and because so much content is black, the Runco Vistage Series also offers incredible operating efficiency. PR The Vistage Series includes Runco’s new DHD-LS™, an ultra-slim (measuring just more than 1 inch tall) video processor and scaler. The Runco DHD-LS allows connection to a myriad of multiple sources, and its elegant design includes an all-glass front that complements the sleek design of the Vistage Series. The DHD-LS includes Runco’s latest ViVix™ processing for exceptional scaling and analog-to-digital signal conversion. It also allows single-wire connectivity to the display and enables individual calibration and control. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 3 1.3 Description, Features and Benefits Introduction Key Features and Benefits ➤ The V-50HD/V-63HD offers these key features and benefits: • Ultra-thin 1.7” panel inside a sleek, elegant design • 50” (V-50HD) or 63” (V-63HD) diagonal screen size • Completely customizable finish options with Runco FinishPalette™ • Emissive Cell Structure™ that delivers exceptional brightness and viewing angles • Solid glass front for better viewing performance when the display is on and a more uniform finish when it is off • Ships with Runco’s new DHD-LS™ ultra-slim video processor and scaler • Optional bottom-mount speaker bar and halo-shaped table stand Y Your V-50HD/V-63HD is shipped with the following items. If any items are missing or damaged, please contact your Runco dealer or Runco Customer Service at (800) 23RUNCO. EL IM IN A R Parts List ➤ • Vistage™ Series Flat Panel Display and DHD Controller • DHD Controller Remote Control Unit and batteries • AC power cords for display panel and DHD Controller • Rack-mounting brackets and hardware for the DHD Controller • Vistage™ Series Quick Setup Guide Optional Accessories: • Wall-Mount Kit (part number 955-0239-00) • Table Stand for V-50HD (part number 955-0225-00) • Table Stand for V-63HD (part number 955-0226-00) • Speaker Bar for V-50HD (part number 997-6255-00) PR • Speaker Bar for V-63HD (part number 997-6257-00) 4 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Controls and Functions 2. Controls and Functions 2.1 Vistage Series at a Glance 1 2 EL IM IN A R Y Figure 2-1 and Figure 2-2 show the V-50HD/V-63HD front-panel controls and indicators. 3 PR Figure 2-1. V-50HD Front-Panel Controls and Indicators 1 2 4 3 Figure 2-2. V-63HD Front-Panel Controls and Indicators Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 5 4 Front-Panel Controls and Indicators Controls and Functions 1. REMOTE CONTROL SENSOR Receives the signals from the remote control. 2. STANDBY INDICATOR Lights blue to indicate that the V-50HD/V-63HD is in standby mode; otherwise, it is off. 3. DISPLAY STAND Optional accessory for table-top installations. 4. SPEAKER BAR Optional accessory that can be mounted to the bottom of the panel. Figure 2-3 shows the rear-panel connector locations on the V-50HD/V-63HD. EL IM IN A R Y Rear-Panel Connectors ➤ 1 2 SECONDARY INPUT SERVICE PORT PRIMARY INPUT PR V-50HD 1 SECONDARY INPUT 2 SERVICE PORT PRIMARY INPUT V-63HD 1 2 (with cover plate removed) (with cover plate removed) SECONDARY INPUT SERVICE PORT PRIMARY INPUT Figure 2-3. V-50HD/V-63HD Rear Panel 6 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Controls and Functions The rear-panel connectors reside behind protective cover plates with cable routing slots. Use a Phillips screwdriver to remove the plates in order to connect cables, and to re-attach them afterward. To minimize the amount of space required behind the panel when wall-mounted, the connectors are recessed and right-angled relative to the rear panel surface (the AC input faces right and the other input connectors face downward). Note 1. AC POWER INPUT Connect the V-50HD/V-63HD to AC power here. • SERVICE PORT For future use. EL IM IN A R • SECONDARY INPUT For future use. Y 2. DHD INPUT PANEL • PRIMARY INPUT HDCP-compliant digital video input. Connect the HDMI output from the DHD Controller to this input. PR Figure 2-4 shows the controls and indicators on the DHD Controller front panel; the paragraphs that follow describe them. 1 2 Figure 2-4. DHD Controller Front Panel 1. STATUS LED Indicates DHD Controller status as follows: • Solid yellow = DHD Controller is in standby mode (off) • Flashing blue = DHD Controller is starting up • Solid blue = normal operation • Off = DHD Controller is shutting down (“cool-down” mode) • Flashing yellow = error condition • Alternately flashing blue/yellow = firmware upgrade in progress 2. REMOTE CONTROL SENSOR Receives the signals from the remote control. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 7 2.2 DHD Controller Front Panel Controls and Functions 2.3 DHD Controller Rear Panel Figure 2-5 shows the rear connector panel on the DHD Controller. HD1 H 1 Y Video Vid deo 1 RS-232 Video 2 HDMI Out To Display HD2 H 2 Pb HDMI 2 4 HDMI 4 5 6 PC / Control HDMI Out Audio Only Ethernet 7 8 9 EL IM IN A R 3 Video 3 Y 2 1 Pr Figure 2-5. DHD Controller Rear Panel 1. POWER INPUT (100 to 240 VAC) Connect the DHD Controller to power here. 2. HD1 / HD2 (5 x Analog BNCs) Two inputs (five BNCs per input) for connecting standard-definition (SD = 480i/576i), enhanced-definition (ED = 480p/576p) or high-definition (HD = 720p/1080i/1080p) component video sources, or RGBHV sources such as personal computers. PR 3. Component / SCART (3 x RCA connectors) SD/HD input for connecting SDTV, EDTV or HDTV component video sources. Also provides RGB input for SCART RGBS sources. 4. Video 1 / Video 2 / Video 3 Standard, composite video inputs for connecting a VCR, camcorder or other composite video source. The Video 1 input also provides composite sync input for SCART RGBS sources. 5. HDMI 1 / HDMI 2 / HDMI 3 / HDMI 4 (Digital) HDCP-compliant digital video inputs for connecting an HDMI or DVI source. 6. Ethernet A female RJ-45 connector for wired network communications. 7. HDMI Out (Audio Only) Connect this output to an audio control system to pass through HDMI audio. Note The DHD Controller does not transmit HDMI CEC control messages from the “HDMI Audio Out” connector. 8. HDMI Out (To Display) Connect this to an HDMI input on your display device. 9. RS-232 (PC / Control) A female, 9-pin D-sub connector for interfacing with a PC or automation/control system. 8 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Controls and Functions Figure 2-6 shows the V-50HD/V-63HD remote control, and the paragraphs that follow describe its functionality. 1 LIGHT 2 3 ON OFF 5 I N P U T EN T ER 7 6 RATIO EXIT 8 ISF NT 9 VID 1 ISF DAY CUST 1 VID 2 1 10 I N P U T EL IM IN A R 4 Y RATIO HD 1 HD 2 HDMI 1 12 HDMI 2 11 6 SCART 8 HDMI 4 13 9 NATIVE PR HDMI 3 3 COMP 5 7 CUST 2 VID 3 2 4 MENU 0 14 16 : 9 4:3 LET BOX V-WIDE CINEMA V-CINE Figure 2-6. DHD Controller/V-50HD/V-63HD Remote Control Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 9 2.4 V-50HD/V-63HD Remote Control Unit Controls and Functions 1. IR OUTPUT INDICATOR Lights when a button is pressed to indicate that an IR signal is being transmitted. 2. LIGHT Press to illuminate the buttons. 3. ON / OFF Press to turn the DHD Controller and display on or off. 4. ENTER Press to select a highlighted menu item or confirm a changed setting. Y 5. Cursor Buttons ( , , , ) Use these buttons to select items or settings, adjust settings or switch display patterns. EL IM IN A R When no menu is present on-screen, the UP and DOWN buttons toggle through the available aspect ratios, in this order: UP Button = Native - Virtual Cinema - Cinema - VirtualWide - Letterbox - 4:3 - 16:9 DOWN Button = 16:9 - 4:3 - Letterbox - VirtualWide - Cinema - Virtual Cinema Native Note For more information about aspect ratios, refer to Table 4-1. PR Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in this order: LEFT Button = HDMI 4 - HDMI 3 - HDMI 2 - HDMI 1 - SCART - HD 2 - HD 1 Component - Composite 3 - Composite 2 - Composite 1 RIGHT Button = Composite 1 - Composite 2 - Composite 3 - Component - HD 1 HD 2 - SCART - HDMI 1 - HDMI 2 - HDMI 3 - HDMI 4 6. EXIT Press this button to exit the current menu and return to the previous one. 7. MENU Press this button to access the OSD controls, or to exit the current menu and return to the previous one. 8. Memory Preset Buttons: ISF NIGHT Press to recall settings for the current input from the “ISF Night” memory preset. ISF DAY Press to recall settings for the current input from the “ISF Day” memory preset. CUST 1 Press to recall settings for the current input from the “Custom 1” memory preset. CUST 2 Press to recall settings for the current input from the “Custom 2” memory preset. 9. VID 1 (1) / VID 2 (2) / VID 3 (3) Press to select a composite video input as the source or to enter the numeric character “1,” “2” or “3.” 10 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Controls and Functions 10. HD 1 (4) / HD 2 (5) Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric character “4” or “5.” 11. COMP (Component) (6) Press to select the Component video input as the source or to enter the numeric character “6.” 12. HDMI 1 (7) / HDMI 2 (8) / HDMI 3 / HDMI 4 (0) Press to select an HDMI input as the source or to enter the numeric character “7,” “8” or “0.” EL IM IN A R 14. Aspect Ratio Selection Buttons Use these buttons to select an aspect ratio directly, as follows: Y 13. SCART (9) Press to select the SCART video input as the source or to enter the numeric character “9.” NATIVE Displays the source signal in its native resolution, centered in the display area. 16:9 For viewing 16:9 DVDs or HDTV programs in their native aspect ratio. 4:3 Scales the input signal to fit 4:3 display mode in the center of the screen. LETBOX (Letterbox) For viewing non-anamorphic (“full-screen”) DVDs on a 16:9 screen. PR V-WIDE (VirtualWide) Enlarges a 4:3 image horizontally in a non-linear fashion to fit 16:9 full screen display. CINEMA For viewing 2.35:1 source material. V-CINE Selects the Virtual Cinema aspect ratio. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 11 Controls and Functions PR EL IM IN A R Y Notes: 12 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Installation 3. Installation Installation must be performed by a qualified custom video installation specialist. Y Note To install batteries in the remote control: EL IM IN A R 1. Press down the tab on the cover and pull the cover in the direction of the arrow. 3.1 Remote Control 2. Insert the included batteries. Ensure that the polarities correctly match the and markings inside the battery compartment. PR 3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in place. • Make sure that the battery polarities are correct when installing the batteries. • Do not mix an old battery with a new one or different types of batteries. • If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage. • Do not expose batteries to excessive heat such as from sunshine, fire or the like. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 13 Notes on Batteries Installation Notes on Remote Control ➤ Operation • Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the DHD Controller. • If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones. • The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting. • Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the DHD Controller, and repeat the operation. 3.2 Quick Setup EL IM IN A R Table 3-1. Installation Overview Y Table 3-1 gives a quick overview of the V-50HD/V-63HD installation process. The sections following this one provide detailed instructions. PR Step Procedure 15 1 Mount the V-50HD/V-63HD on a wall (refer to instructions provided with the wall-mount kit) —OR— Attach table stand (refer to instructions provided with the stand) 2 Connect the DHD Controller to the display 17 3 Connect signal sources to the DHD Controller 18 22 4 Connect other external equipment to DHD Controller (optional): • Audio processor or secondary display device • Control system interface (RS-232) • Network hub, router or gateway (Ethernet) 5 Apply power to the display and DHD Controller 24 6 If using the V-50HD/V-63HD with a computer, adjust computer display properties 25, 38 29 through 44 7 DHD Controller input calibration: adjust the following for each DHD Controller input and display mode (resolution/frame rate); save settings when finished: • Aspect ratio • Color level • Brightness • Tint • Contrast • Input position • Color temperature and white balance 14 Downloaded From TV-Manual.com Manuals For Details, Refer to page... Vistage™ Series Flat-Panel Display Installation/Operation Manual Installation Proper installation of your V-50HD/V-63HD will ensure the highest possible picture quality. Whether you are installing the V-50HD/V-63HD temporarily or permanently, you should take the following into account to ensure that it performs optimally. To install the V-50HD/V-63HD, you will need either an optional table stand or wall-mounting kit. EL IM IN A R Runco recommends that this be done by a custom installation specialist. Mounting the V-50HD/V-63HD on a Wall or Table Stand Y If you are wall-mounting a V-50HD/V-63HD, ensure that the wall-mount bracket is installed according to the instructions included with it. The wall must be capable of supporting a redundant weight factor three (3) times the weight of the display, or be reinforced. 3.3 Installation Considerations 1. Use only a Runco-approved wall-mount kit or table stand that is specifically designed for your display. Refer to Parts List on page 4 for ordering information. Note 2. If you are wall-mounting the V-50HD/V-63HD, you must attach the video and power cables to the display before mounting it. Due to its extraordinarily high level of video processing performance, the DHD Controller may distribute video signals with a perceptible level of audio latency. In order to easily solve this issue, Runco recommends using the DHD Controller with a high-quality audio receiver that has the ability to effectively synchronize audio and video signals. PR Most mainstream audio receiver/switchers have the ability to synchronize the audio and video to the Advanced Television Systems Committee (ATSC) prescribed tolerances. According to the ATSC, the sound program should never lead the video program by more than 15 milliseconds, and should never lag behind the video program by more than 45 milliseconds. In addition, many video displays and A/V receivers introduce additional latency that needs to be compensated for during the installation. Table 3-2 shows the amount of possible audio latency given different signal input timings. Table 3-2. Possible Audio Latency for Various Input Timings Input Timing Possible Audio Latency (milliseconds) 480i 133 480p 83 576i 160 576p 100 720p/50 100 720p/60 83 1080i/25 160 1080i/30 133 1080p/24 125 1080p/50 80 1080p/60 67 Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 15 Audio/Video Synchronization Issues Installation Ventilation ➤ If you are mounting the V-50HD/V-63HD in an enclosure, leave sufficient space on all sides between it and surrounding objects, as shown in Figure 3-1. This allows heat to disperse, maintaining the proper operating temperature. EL IM IN A R PR Ambient Light ➤ Other Considerations ➤ Wall 50mm (2") 50mm (2") Y 50mm (2") 50mm (2") Wall Figure 3-1. Ventilation Requirements for Enclosure Mounting In general, minimize or eliminate light sources directed at the display. Contrast ratio in your images will be noticeably reduced if light directly strikes the display, such as when a shaft of light from a window or floodlight falls on the image. Images may then appear washed out and less vibrant. Other considerations and tips that can help improve your installation: • Keep the ambient temperature constant and below 35°C (95°F). Keep the display away from heating and/or air conditioning vents. Changes in temperature may cause drifts in the display circuitry, which may affect performance. • Keep the display away from devices that radiate electromagnetic energy such as motors and transformers. Common sources of these include slide projectors, speakers, power amplifiers and elevators. Rack-Mounting the DHD ➤ Controller The DHD Controller can be placed on any flat, stable surface such as a shelf or table, or it can be rack-mounted using the supplied mounting hardware. Place the DHD Controller in a location that provdes easy access to the power connector. To mount the DHD Controller in a standard, 19-inch equipment rack, install the mounting ears on either side of the chassis using the supplied screws. Then, secure the mounting ears to the rack. 16 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Installation Proceed as follows to connect the DHD Controller to the V-50HD/V-63HD, your video sources, external controller(s) – if present – and AC power. To access the rear-panel connectors, use a Phillips screwdriver to loosen the screws securing the protective cover plates (see Figure 2-3) to the panel, then remove the plates. 3.4 Connections to the V-50HD/V-63HD and DHD Controller When connecting your equipment: • Turn off all equipment before making any connections. • Use the correct signal cables for each source. Y • For best performance and to minimize cable clutter, use high-quality cables that are only as long as necessary to connect two devices. (Don’t use a 20-foot cable when a 6-foot cable will suffice.) EL IM IN A R • Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them. Connect the HDMI Out To Display connector on the DHD Controller to the PRIMARY INPUT connector on the V-50HD/V-63HD. See Figure 3-2. Then, re-attach the input cover plate, routing the cable through the nearest slot on the plate. Use an HDMI cable for this connection. A DVI cable with DVI-to-HDMI adapters will not work. PR Caution PRIMARY INPUT SECONDARY INPUT SERVICE PORT PRIMARY INPUT HDMI Out To Display HD1 Y Video deo 1 RS-232 V Video ideo 2 HDMI Out To Display HD2 Y G Pb B Pr R H V Pb Pr Video 3 HDMI 2 HDMI 4 Ethernet Figure 3-2. Connecting the V-50HD/V-63HD to the DHD Controller Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 17 HDMI Out Audio Only Connecting the DHD Controller to the V-50HD/V-63HD Installation Connecting Source ➤ Components to the DHD Controller Connect your video sources to the DHD Controller as shown and described in the sections that follow. HDMI Source Connections: See Figure 3-3. Use the HDMI inputs whenever possible. Not only does this ensure the best possible picture quality, it provides a communication channel for CEC command messages between the display and source component (if both support CEC). Tip You can also connect computers with DVI output to these inputs. Refer to Supported Timings on page 75 for a list of compatible input signals. EL IM IN A R Y Note HDMI 1 HDMI 3 RS-232 Video 2 Video 3 HDMI 2 HDMI 4 Ethernet HDMI Out To Display HDMI Out Audio Only HDMI AV OUT PR HDMI AV OUT HDMI AV OUT HDMI AV OUT HDMI sources (BD, DVD, DTV Set-Top Box etc.) Figure 3-3. HDMI Source Connections 18 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Installation Component Video Source Connections: Connect your component video sources to the HD1, HD2 and/or Component/SCART inputs as shown in Figure 3-4. HD1 Y Video 1 Video 2 Pb Pr Video 3 HD2 Y G Pb B Pr R H V COMPONENT VIDEO OUT PB PR DTV-Set-Top Box (DTV-STB) PR BD/DVD Y EL IM IN A R Y RCA-to-BNC adapter Figure 3-4. Component Video Source Connections Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 19 Installation RGBHV Source Connections: Connect personal computers and/or other RGB sources to the HD1 and/or HD2 inputs as shown in Figure 3-5. HD1 HD2 V-Sync V EL IM IN A R H-Sync H Y Pr R Red Pb B Blue Green Y G RGB Camcorder Computer PR or Figure 3-5. RGBHV Source Connections 20 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Installation SCART RGBS Source Connections: Connect the green, blue and red outputs from your SCART source to the Component/SCART input on the DHD Controller. Connect the sync output from your SCART source to the Video 1 input on the DHD Controller. See Figure 3-6. HD1 Y Video 1 Video 2 Pb Pr Video 3 HD2 H V Y Pr R VCR SCART-to-RGBS adapter Sync Blue EL IM IN A R Green Pb B Red Y G Green DVD/DTV STB Blue Red Sync Gaming Console Figure 3-6. SCART RGBS Source Connection PR Composite Source Connections: See Figure 3-7. HD1 HDMI 1 Y Video 1 Video 2 Pb Pr Video 3 Pr R H V VCR Camcorder HDMI 2 Composite Pb B Composite Y G Composite HD2 Composite Composite Gaming Console Composite Figure 3-7. Composite Video Source Connections Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 21 Installation Connecting an Audio ➤ Processor or Secondary Display Device to the DHD Controller (Optional) The DHD Controller provides a second HDMI output (labeled HDMI Out (Audio Only)) for connection to an audio receiver/switching system or secondary display device for monitoring purposes. See Figure 3-8. The DHD Controller does not transmit HDMI CEC control messages from the “HDMI Audio Out” connector. For more information about CEC, refer to Using HDMI CEC Messages on page 68. Note 1 Video deo 1 Video Video 2 Y HDMI 3 HDMI 1 Y Pr Video 3 HDMI 2 HDMI 4 Ethernet EL IM IN A R Pb PR RS-232 HDMI Out To Display 2 HDMI Out Audio Only Secondary Display Audio Processor/ Switcher or Figure 3-8. Audio Processor Connection to DHD Controller 22 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Installation Use a straight-through, 9-pin RS-232 cable to connect a PC or control/automation system (if present) to the RS-232 port on the DHD Controller; see Figure 3-9. RS-232 Controller Connection For more information about using this connection, refer to External Control on page 59. HDMI 3 RS-232 HDMI Out To Display Ethernet HDMI Out Audio Only PC / Control 5 4 8 1 2 7 6 EL IM IN A R 9 3 Y HDMI 4 2 Receive Data 3 Transmit Data 5 Ground to Automation/ Control System or PC (none of the other pins are used) Figure 3-9. RS-232 Control System Connection Use a standard, Category 5 network cable with an RJ-45 plug to connect a network hub, router or gateway to the Ethernet port on the Primary DHD Controller; see Figure 3-10. PR For more information about configuring and using this connection, refer to Network on page 48. HDMI 3 HDMI 4 Ethernet RS-232 HDMI Out To Display HDMI Out Audio Only 1 8 to Ethernet Hub, Router or Gateway 1 Transmit Data + 2 Transmit Data 3 Receive Data + 6 Receive Data - Figure 3-10. Ethernet Network Connection to Primary DHD Controller Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 23 Ethernet Network Connection Installation Connecting to AC Power ➤ The V-50HD/V-63HD ships with two (2), AC power cords: one for the DHD Controller and one for the display. 1. Plug the female end of one of the power cords into the AC receptacle on the rear of the V-50HD/V-63HD (AC 100V ~ 240V); see Figure 2-3. 2. Connect the other end to your AC power source. 3. Re-attach the AC input cover plate, routing the power cord through the slot on the plate. 4. Connect the DHD Controller to a nearby AC outlet using the other AC power cord. 1. Power up your source components. 2. Press the ON button on the remote control to turn on the system. The front-panel status indicator on the DHD Controller flashes blue to indicate that it is powering up. Y 3.5 Turning on the Power PR EL IM IN A R 3. When the display is ready for use, the front-panel status indicator on the DHD Controller lights solid blue. 24 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation 4. Operation To maximize image quality when using the V-50HD/V-63HD with a personal computer, you may need to adjust the display properties of your computer’s video card. To do this on a Microsoft® Windows®-based PC: EL IM IN A R Y 1. Choose Settings from the Windows Start Menu and click on “Control Panel.” 2. Double click on the Display icon. 3. Click the Settings tab on the display dialog box. PR 4. Set the Screen area to 1024x768 pixels. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 25 4.1 Setting the Computer Display Properties Operation EL IM IN A R Y 5. Click the Advanced button and click the Monitor tab on the dialog box. Set the Refresh Frequency to 60Hz and click OK. Note 1. The native resolution of the V-50HD/V-63HD is 1920 x 1080. Other horizontal or vertical resolutions may be scaled upward or downward to fit the display. 2. With most computers, you can get the best picture at 1024 x 768 @ 60Hz. To prevent image retention (burn) on your display, ALWAYS use a screen saver and set it to the shortest possible time. PR WARNING 26 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation To display the Main Menu, press the MENU button on the remote control or DHD Controller front panel (Figure 2-4). To select a menu item, use the and buttons on the remote control or DHD Controller front panel to highlight it. Then, to confirm your selection, press ENTER on the remote control or DHD Controller front panel. 4.2 Using the On-Screen Menus Screen Picture Input Position Memory Presets Sleep Timer Screen 1 / Screen 2 Information Signal System (read-only) Network Field Service Manufacturing Gain Offset EL IM IN A R Aspect Ratio Brightness Contrast Color Tint Sharpness Noise Filter Left/Right Up/Down Width Height Overscan Overscan Mode (Zoom/Crop) Phase (RGB/Component/SCART signals only) Tracking (RGB/Component/SCART signals only) Recall ISF Night or ISF Day Recall/Save Custom 1 or Custom 2 Reset Custom 1 and Custom 2 to Factory Default Off, 30 Minutes, 60 Minutes, 90 Minutes, 2 Hours or 4 Hours PR Input Source Composite 1 Composite 2 Composite 3 Component HD 1 HD 2 SCART HDMI 1 HDMI 2 HDMI 3 HDMI 4 16:9 4:3 Letterbox VirtualWide Cinema Virtual Cinema Native Y The V-50HD/V-63HD OSD menus are arranged hierarchically, as shown in Figure 4-1. Some menu options apply only to certain input signal types. For example, Phase and Tracking can only be adjusted for RGB, Component video or SCART signals. Display Color Common Gamma Settings Color Temp Calibration Display Color - Panel Brightness Panel Settings Power Mode Brightness Contrast Input Image Color Tint Sharpness Gain Offset Input Color Chroma Delay Noise Filter Save ISF Night Back / Confirm Save ISF Day Memory Preset Copy/Paste Aspect Ratio Output Shift Image Alignment Splash Configure OSD Position Note: Default settings appear in bold type. Figure 4-1. V-50HD/V-63HD OSD Menu Structure Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 27 Left/Right Up/Down Width Height Corner Alignment Midpoint Alignment Owner Name ISF Calibrated ISF Other Splash Timer Splash Enable Hor. / Ver. -100, -99... 0 ... 99, 100 (Red, Green, Blue) Mode (Simple / Advanced) Simple (1.8, 2.0, 2.2, 2.35 or 2.5) Advanced (0 (2.2 gamma curve), 1, 2, 3 ... 20 (custom gamma tables)) Simple (3200K, 5500K, 6500K, 7500K or 9300K) 0, 1, 2, 3 ... 100 High / Normal / Eco -50, -49 ... 0 ... 49, 50 -32, -31... 0 ... 31, 32 (HD 1, HD 2 and Component inputs only) 0, 1, 2 ... 7 (Composite inputs only) 0, 1, 2 ... 63 Copy Settings Paste Settings Copy Settings Paste Settings -50, -49 ... 0 ... 49, 50 -50, -49, 48 ... 0 Top Left / Top Right / Bottom Left / Bottom Right Center / Top Middle / Left Middle / Right Middle / Bottom Middle 5, 6, 7 ... 15 ... 59, 60 On/Off 0, 1, 2 ... 100 Operation Color Bars 1 Color Bars 2 Focus Grey Bars Rename/Restore Input Names Picture Orientation Display Device - Configure Diagnostics IP Configuration Auto Firmware Upgrade Network E-Mail Notification Service Remote Network Control Auto, REC601, REC709, RGB-PC or RGB-Video EL IM IN A R Color Space Language Miscellaneous Sync Threshold HDMI Auto, Floor Front, Ceiling Front, Floor Rear or Ceiling Rear White, Red, Green, Blue, Yellow, Cyan, Magenta DHCP (On / Off), IP Address, Subnet Mask, Default Gateway, Communication Test Auto Check for New Firmware, Auto Perform Upgrade, Check for New Firmware E-Mail Address, Error Notification, Error Notification to Runco, Periodic Service Notification, Customer Information, E-Mail Calibration Data On / Off (Not available on Composite 1, Composite 2 or Composite 3 inputs) English, Français, Deutsch, Italiano, Español, Svenska, (Simplified Chinese), (Traditional Chinese), Português, (Russian), (Japanese) or (Korean) 0 (no timeout) or 5, 6, 7 ... 15 ... 60 sec. On / Off Y Test Video PR Front Panel Brightness Auto Power Off Standby Mode System Reset OSD Timer OSD Messages Blank Screen Color Sidebar Color Film Mode (SD sources only) CUE (Chroma Upsampling Error) Remote Code 0, 1, 2 ... 15 HDMI EDID Extension Audio Format CEC HPD Toggle Rejection Logo LED Standby LED Enable Hours Low Power / Fast Startup Red/Green/Blue = 0, 1, 2, 3 ... 255 On / Off On / Off 00, 01, 02 ... 17 ... 31 (HD 1, HD 2 and Component inputs only) On / Off (per HDMI input) Combined / HDMI Out (To Display) / HDMI Out (Audio Only) On / Off On / Off 0 (off), 1, 2 ... 31 On / Off On / Off 1, 2, 3, 4, ... 8 ... 23, 24 Figure 4-1. V-50HD/V-63HD OSD Menu Structure (continued) 28 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation The Main Menu is the starting point for accessing all DHD Controller functions. Main Menu (You must enter a passcode to access the Calibration and Service menus.) Runco Video Input Source Aspect Ratio Screen Picture Input Position Memory Presets Sleep Timer EL IM IN A R Y Information From the Main Menu, select Input Source to choose a video signal source. PR The active source is indicated by an arrow (Î) to its left; in this example, Composite is the active source. To change the aspect ratio (size and shape) of the projected image, select Aspect Ratio from the Main Menu and press ENTER. Select the appropriate aspect ratio for your screen size and the type of program material being viewed; refer to Table 4-1. The currently-selected aspect ratio is indicated by a “7” to its left; in this example, 16:9 is selected. Note that some aspect ratios are unavailable and/or not useful with certain types of source material. The optimal setting depends on a number of factors, such as: • The aspect ratio of the source material, as broadcast or encoded on the playback medium. • The “display type” (16:9 or 4:3) and output resolution settings at the source component. Most modern DVD/BD players and set-top boxes have such controls. • Viewer preference (original aspect ratio with “black bars,” or a full-screen presentation with some distortion or cropping). Note The aspect ratio selection is automatically saved for each input and resolution. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 29 Calibration Service Input Source Input Source Î Composite 1 Composite 2 Composite 3 Component HD 1 HD 2 SCART HDMI 1 HDMI 2 HDMI 3 HDMI 4 Aspect Ratio Aspect Ratio 7 16:9 4:3 Letterbox VirtualWide Cinema Virtual Cinema Native Operation Table 4-1. Aspect Ratio Settings Aspect Ratio Remote Control Key 16:9 16:9 Description Select 16:9 to view 16:9 DVDs and HDTV programs in their native aspect ratio. EL IM IN A R Y 16:9 Image on 16:9 Screen (Display) 4:3 images are stretched horizontally to fit a 16:9 screen. 4:3 Image, stretched to fill 16:9 Screen (Display) 4:3 VirtualWide 4:3 Image on 16:9 Screen (Display) 4:3 scales the input signal to fit in the center of the 16:9 screen. 4:3 is the aspect ratio used by older computer monitors, standard television programming and most VHS video cassettes. 4:3 Image on 16:9 Display (Letterbox aspect ratio) Letterbox mode scales (zooms in on) a 4:3 image linearly (by the same amount on all sides) to fill a 16:9 display. Use Letterbox for viewing LaserDisc movies or “full-screen” DVDs on a 16:9 screen. LET BOX PR Letterbox 4:3 V-WIDE 4:3 Image on 16:9 Screen (Display) VirtualWide scales a 4:3 image NON-linearly (more on the sides than in the center) to fit a 16:9 screen. 4:3 Image on 16:9 Screen with VirtualWide 30 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation Table 4-1. Aspect Ratio Settings (continued) Aspect Ratio Remote Control Key Cinema CINEMA Description V-CINE A 2.35:1 image is stretched anamorphically in both directions to fill a 16:9 display area. EL IM IN A R Virtual Cinema Y 2.35:1 Image on 16:9 Screen Select Cinema to view 2.35:1 source material on a 16:9 screen. The upper and lower portions of the screen are masked, but the geometry of the active image area is not changed. 2.35:1 Image on 16:9 Screen The 2.35:1 image is cropped on all sides. 2.35:1 Image on 16:9 Screen with Virtual Cinema NATIVE PR Native 1080i HDTV Image 720p HDTV Image Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals Select Native to display the source signal in its native resolution, centered in the display area with no re-sizing or overscan. This means, for example, that 720p HDTV programs will display with unused pixels on all sides: 320 on the left and right sides and 180 above and below. With SDTV and EDTV sources, the DHD Controller scales the image horizontally to achieve a 16:9 aspect ratio. 31 Operation Screen ➤ The Screen Menu allows you to recall multiple sets of stored values for certain controls (Output Shift and Image Alignment, to name two) that are saved for each aspect ratio. Such settings are also saved “per screen.” To recall the Output Shift and Image Alignment settings associated with “Screen 1” or “Screen 2,” make that selection here. Picture ➤ Use the controls in the Picture Menu to calibrate each DHD Controller input to achieve optimum picture quality. Screen Screen 1 Screen 2 Picture Brightness Contrast Y Color Noise Filter EL IM IN A R Tint Sharpness The DHD Controller has been designed to incorporate setup and calibration standards established by the Imaging Science Foundation (ISF). The ISF has developed carefully crafted, industry-recognized standards for optimal video performance and has implemented a training program for technicians and installers to use these standards to obtain optimal picture quality from Runco video display devices. Accordingly, Runco recommends that setup and calibration be performed by an ISF certified installation technician. All signal types require separate processing. Therefore, you need to calibrate each DHD Controller input separately. Note When you change a picture quality setting, save the change to a preset afterwards. Otherwise, the change will be lost when a different input is selected. (Picture quality settings are saved for each input and display mode separately.) For information about saving settings, refer to Memory Presets on page 38. PR Although it may be possible to obtain satisfactory picture quality using the naked eye and regular program material, Runco recommends using an external test pattern source (Ovation Multimedia, Digital Video Essentials or AVIA test DVD or equivalent) for best results. Connect your test pattern source to the input that you are calibrating and proceed as follows. Perform the adjustments in the order listed here. Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an acronym for “Picture Line-Up Generation Equipment.”) Figure 4-2 shows a typical PLUGE pattern. Below Black Above Black Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness 32 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation PLUGE patterns vary but generally consist of some combination of black, white and gray areas against a black background. The example above includes two vertical bars and four shaded boxes. Select Brightness from the Picture menu and press ENTER. Adjust the brightness so that: • The darkest black bars disappear into the background. • The dark gray areas are barely visible. • The lighter gray areas are clearly visible. • The white areas are a comfortable level of true white. • The image contains only black, gray and white (no color). EL IM IN A R Y Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the one shown in Figure 4-3. Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast Note PR Select Contrast and press ENTER. Adjust the contrast to a point just below which the white rectangle starts to increase in size. Brightness and contrast controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 33 Operation blue red EL IM IN A R Y magenta green cyan yellow gray Color Saturation: On your external test pattern source, select a color bar pattern like the one shown in Figure 4-4. Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint 1. Press the MENU button on the remote control or DHD Controller front panel. 2. Select Service from the Main Menu and press ENTER. 3. Enter the Service menu passcode. 4. Select Display Device from the Service menu and press ENTER. 5. Press ENTER again to select Configure. PR 6. Select Diagnostics and press ENTER. 7. Select Blue from the Diagnostics menu, then press ENTER to display only the blue color channel. 8. Press EXIT (or MENU) repeatedly to return to the Main Menu. 9. Select Picture from the Main Menu and press ENTER. 10.Select Color from the Picture menu and press ENTER. 34 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation EL IM IN A R Y blue red magenta green cyan yellow gray 11.Adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue: Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener. To adjust the tint, enable “blue only” display mode in the Diagnostics menu, as you would for adjusting color saturation (refer to the previous section, Color Saturation). Note PR Select Tint from the Picture menu and press ENTER. Adjust the tint level until the cyan and magenta color bars (on either side of the green bar) appear to be a single shade of blue. Like the brightness and contrast controls, the color and tint controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 35 Operation EL IM IN A R Y Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5. Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them. PR Figure 4-5. Typical Test Pattern for Adjusting Sharpness Input Position ➤ Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Picture menu. The Noise Filter is useful for clearing up noisy images from 480i video sources. Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image. Use the controls in the Input Position Menu to fine-tune the aspect ratio and image position for the current source. Input Position Left/Right Up/Down Note The input position settings are automatically saved for each input and resolution. Width Height Overscan Overscan Mode Phase Tracking Left/Right: Select Left/Right from the Input Position menu to shift the projected image horizontally. Press to shift the image to the right; press to shift it to the left. Up/Down: Select Up/Down from the Input Position menu to shift the projected image vertically. Press to shift the image upward; press to shift it downward. Width: Select Width from the Input Position menu to change the projected image width. Press to increase the width; press to decrease it. 36 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation Height: Select Height from the Input Position menu to change the projected image height. Press to increase the height; press to decrease it. Overscan/Overscan Mode: Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area. Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Overscan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area. Y For HDTV, DVDs and other video sources, Overscan is generally not necessary or desirable. EL IM IN A R This control defines the amount of overscan applied to the image. The range is from 0 to 20. There are two overscan modes: • In Crop mode, each increment adds a mask at the top, bottom, left and right edges of the source image equal to 0.5% of the displayed horizontal resolution (1% total). A setting of 10, for example, crops the image 5% on all sides or 10% total. • In Zoom mode, each increment adds a factor to the scaling of the source image so that the vertical and horizontal resolutions are 100% plus 1% increments of the size determined by the aspect ratio function. A setting of 10, for example, zooms in on the image 5% on all sides or 10% total. Figure 4-6 illustrates the effect of each overscan mode setting. Off 16:9 Zoom PR 4:3 Crop = Source Image Area = Edge Noise = Screen (16:9) Figure 4-6. Overscan Modes Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 37 Operation Phase (RGB, Component or SCART sources): This control adjusts the phase of the pixel sampling clock relative to the incoming signal. Adjust the phase when an RGB, Component or SCART image still shows shimmer or “noise” after Tracking has been optimized. Adjust the Phase after adjusting Tracking (see below). Tip Y For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. Adjust the slidebar until the image stabilizes and each pixel is clearly defined. You may notice that you can stabilize the image at more than one point. Use either setting in such cases. EL IM IN A R Tracking (RGB, Component or SCART sources): Tracking determines the frequency of the pixel sampling clock, indicated by the number of incoming pixels per line, so that all pixels generated by a particular source are sampled. Steady flickering or several soft vertical stripes or bands across the entire image indicates poor pixel tracking. Proper pixel tracking helps ensure that the image quality is consistent across the screen, that aspect ratio is maintained and that pixel phase (see above) can be optimized. Memory Presets ➤ Memory Presets Î ISF Night For each input, the DHD Controller lets you save image quality settings as presets that you can recall at a later time. You can create up to four presets per input and display mode (resolution and frame rate). The DHD Controller stores the following display modes in each memory preset: ISF Day Save Reset Custom 2 Save Reset PR Custom 1 • 480i • 480p • 576i • 576p • 720p/24 Hz • 720p/25 Hz • 720p/30 Hz • 720p/50 Hz • 720p/60 Hz • 1080i/50 Hz • 1080i/50 Hz (Australia) • 1080i/60 Hz • 1080p/24 Hz • 1080p/25 Hz • 1080p/30 Hz • 1080p/50 Hz • 1080p/60 Hz Use the Memory Presets menu to recall saved image presets, or to save image settings in the “Custom 1” or “Custom 2” memory location. The currently-selected preset is indicated by a “Δ to its left; in the example shown here, ISF Night is selected. 38 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation You should save changes to any of the following settings to a preset; otherwise they will be lost when a new input source or resolution is selected: • Brightness • Contrast • Color saturation • Tint • Sharpness • Gamma To select a memory preset, press or to highlight it and press ENTER. Y • Color temperature and white balance Note EL IM IN A R To save the settings for the current input and display mode to the Custom 1 or Custom 2 memory preset, select it, press or to highlight Save and press ENTER. To save the settings for the current input and display mode to the ISF Night or ISF Day memory preset, select Save ISF Night or Save ISF Day from the Calibration menu (refer to Save ISF Night/Save ISF Day on page 44). To reset the Custom 1 or Custom 2 memory preset to its factory-default state, select it, press or to highlight Reset and press ENTER. PR Select Sleep Timer from the Main Menu to turn off the V-50HD/V-63HD after a specified interval. Press or to select Off, 30 Minutes, 60 Minutes, 90 Minutes, 2 Hours or 4 Hours. Then, press ENTER. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals Sleep Timer Sleep Timer Î Off 30 Minutes 60 Minutes 90 Minutes 2 Hours 4 Hours 39 Operation Information ➤ Information Signal System Signal / System: Select Information from the Main Menu, then choose either Signal or System to display information about the current input signal (resolution, frequency, type et cetera) and installed firmware versions, as well as other information that uniquely identifies your DHD Controller and display device. Should you ever need to contact Runco Technical Support, this information will help them answer your questions or resolve product performance issues. Network Field Service Manufacturing MAC Address 1A:2B:3C:4D:5E:6F IP Address 192.168.0.150 Subnet Mask 255.255.0.0 Default Gateway 192.168.1.1 Enabled Model DHD-LS 1080p/60 Display Name V-50HD/V-63HD Input Resolution 1920x1080 Output Resolution 1920x1080 Vertical Freq 59.94 Hz Horizontal Freq 67.500 kHz Pixel Clock 148.500 MHz Color Space REC709 Sync Type Separate Memory Preset ISF Night Y HDMI 1 Signal Format Serial Number 00000000 Boot Version 4.0 Firmware Version 4.0 Micro Version 4.0 Network: Select Information from the Main Menu, then choose Network to display information about the Ethernet network connection. To enable network communication via Ethernet, refer to IP Configuration on page 48. Field Service / Manufacturing: The Field Service and Manufacturing menus are password-protected and intended for use only by Runco service personnel and factory technicians. PR Network Status Connected Input Source EL IM IN A R Network DHCP System Signal 40 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation Use the Calibration menu to perform advanced picture quality adjustments. This menu should be used by ISF-certified technicians only. Calibration Calibration Note You must enter a passcode to access the Calibration menu. ISF Settings Display Color Input Image To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the Memory Presets menu (see page 38) or use the corresponding remote control buttons. Input Color Save ISF Night Save ISF Day Y Display Color - Common Settings: Use the Display Color - Common Settings menu to adjust the color balance at the DHD Controller output. These settings are saved independently for each input and display mode. EL IM IN A R • Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red (Pr), green (Y) or blue (Pr), decrease the Gain for that color. • Offset: Use the Offset controls to correct color imbalances in the dark areas of the image. A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red (Pr), green (Y) or blue (Pr), decrease the Offset for that color. • Gamma: Select Gamma from the Display Color - Common Settings menu to choose a de-gamma curve. Used correctly, the Gamma control can improve contrast while maintaining good details for blacks and whites. If excess ambient light washes out the image and it becomes difficult or impossible to see details in dark areas, lower the gamma setting to compensate. This improves contrast while maintaining good details for blacks. Conversely, if the image is washed out and unnatural, with excessive detail in black areas, increase the setting. PR • Mode: With the V-50HD/V-63HD, two Gamma adjustment modes are available: Simple or Advanced. The two modes are mutually exclusive; when you select the Simple mode, the Advanced selection in the Gamma menu is grayed out. Likewise, when you select Advanced, the Simple selection is grayed out. • Simple: Use the Simple Gamma control to perform gamma correction at the display according to a simple power law gamma function. The value chosen here corresponds to the power variable in this equation: Output = InputPower The DHD Controller applies this gamma curve to all three primary color channels (red, green and blue). • Advanced: To select a custom gamma curve, select Mode from the Gamma menu and set it to Advanced. Then, select Advanced from the Gamma menu to select one of up to 20 pre-programmed gamma tables. Custom gamma tables provide the ability to perform complex, non-linear gamma correction on each primary color channel independently of the others. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 41 Copy/Paste Output Shift Image Alignment Splash Configure OSD Position Operation • Color Temp: Select Color Temp from the Display Color - Common Settings menu to adjust the color temperature. Color temperature establishes the “color of gray” by adjusting the 75% white point to various color points. What are “color points?” A “color point” is an x/y coordinate pair that defines a color’s location on the standard CIE chromaticity graph, shown in Figure 4-7. (CIE stands for “Commission Internationale de l’Éclairage” (International Commission on Illumination), the organization responsible for color measurement and management standards.) 1.0 y EL IM IN A R Y 0.9 0.8 0.7 Green 0.6 10000 8000 6667 5714 5000 Red 2222 2500 D93 0.3 0.2 PR 2857 4000 D50 D65 3333 Cyan 0.4 2000 Yellow 0.5 Magenta 0.1 Blue 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 x 1.0 Figure 4-7. CIE 1931 Chromaticity Diagram • Simple: Select Simple mode from the Color Temp menu to choose one of five color temperature presets: 3200K, 5500K, 6500K, 7500K and 9300K. The default setting, 6500K, is appropriate for most situations. Higher settings produce a “bluer” picture; lower ones impart a reddish hue to the image. Table 4-2 lists the x- and y-coordinates for each color temperature preset in “Simple” mode. Table 4-2. Color Temperature Presets and Associated Color Points Associated x/y Values Color Temperature Preset x y 3200K 0.423 0.404 5500K 0.332 0.348 42 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation Table 4-2. Color Temperature Presets and Associated Color Points Associated x/y Values Color Temperature Preset x y 6500K 0.313 0.329 7500K 0.299 0.315 9300K 0.284 0.298 Y Display Color - Panel Settings: These settings are also saved independently for each input and display mode. Tip EL IM IN A R • Panel Brightness: The Panel Brightness control changes the apparent brightness of the displayed image. Its effect is similar to that of a lamp intensity control on a projector. Use a higher setting for rooms with a lot of ambient light. Use a lower setting for more “theater-like” viewing conditions (little or no ambient light). To prolong the life of the display, set the Panel Brightness only as high as is necessary to produce the desired brightness. • Power Mode: Select Power Mode from the Display Color - Panel Settings menu to set the power consumption threshold for the panel: High, Normal or Eco. The default setting is High. Input Image: The Input Image controls are functionally similar to those in the Picture menu (refer to page 32), but are accessible only by entering the Calibration menu passcode. The Input Image settings establish the “zero point” for the Picture menu settings, whose values represent offsets from the Input Image settings. For example, if you set Brightness to 10 in this menu, setting Brightness to 10 in the Picture menu results in an actual setting value of 20 (10+10). PR Note Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but adjust the color balance of the incoming signal. These settings are also saved independently for each input and display mode. • Gain/Offset (HD1, HD2 and Component/SCART inputs only): These controls operate similarly to those in the Display Color - Common Settings menu (described on page 41), but affect the Y, Pb and Pr signal components rather than the red, green and blue channels. • Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a composite video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them. • Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i video sources. Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 43 Operation Save ISF Night/Save ISF Day: Whenever you make a change to the ISF settings, you should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to do this. Memory Preset Copy/Paste - Memory Preset: You can copy and paste settings from one memory preset to another. This gives you a convenient starting point for creating a new preset based on an existing one, to make the calibration process less time-consuming. Aspect Ratio For example, you can use the Copy/Paste Memory Preset feature to: Copy/Paste • Apply settings from HDMI 1 to HDMI 2, or from HD1 to HD2. Memory Preset • Calibrate an input for 720p source signals, then use those settings for 1080i sources. Copy Settings • Duplicate ISF Night settings for a given source and signal format and save them in the Custom 1 memory preset. Copied From: To use this feature, select Copy/Paste from the Calibration menu, then select Memory Preset. EL IM IN A R Y Paste Settings Input Source HDMI 1 Signal Format 1080p/60 Memory Preset ISF Night • Memory Preset - Copy Settings: Select Copy Settings from the Copy/Paste Memory Preset menu to place the settings for the current input source, signal format (resolution and frame rate) and memory preset onto a “clipboard,” which is a temporary memory location. When you do, the message “Settings Copied” briefly appears on-screen. The Copy/Paste menu then re-appears, indicating the source of the copied settings. Note Copied settings are not retained after a power cycle. PR • Memory Preset - Paste Settings: To apply the settings on the clipboard to a different input source, signal format and/or memory preset, do any or all of the following: • Switch to another input (for example, from HD1 to HD2). • Change the output signal format at the source (for example, from 720p/60 to 1080i/60). • Switch to another Memory Preset (for example, from ISF Night to Custom 1). Then, select Paste Settings from the Copy/Paste Memory Preset menu. If you want to keep these new settings, you must save them! (Refer to Save ISF Night/Save ISF Day on page 44 or Memory Presets on page 38.) Memory Preset Copy/Paste - Aspect Ratio: You can also copy and paste certain settings, such as those for Output Shift and Image Alignment (refer to page 45) from one aspect ratio or “screen” (refer to Screen on page 32) to another. Aspect Ratio To do this, select Copy/Paste from the Calibration menu, then select Aspect Ratio. Copy/Paste Aspect Ratio Copy Settings Paste Settings • Aspect Ratio - Copy Settings: Select Copy Settings from the Copy/Paste Aspect Ratio menu to place the Output Shift and Image Alignment settings for the current aspect ratio onto a “clipboard,” which is a temporary memory location. When you do, the message “Settings Copied” briefly appears on-screen. The Copy/Paste menu then re-appears, indicating the source of the copied settings. Copied From: Aspect Ratio 16:9 Screen Screen 1 Note Copied settings are not retained after a power cycle. 44 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation • Aspect Ratio - Paste Settings: To apply the Output Shift and Image Alignment settings on the clipboard to a different aspect ratio and/or screen, do either of the following: • Switch to another aspect ratio (for example, from 16:9 to Cinema). • Switch from Screen 1 to Screen 2 or vice versa. Then, select Paste Settings from the Copy/Paste Aspect Ratio menu. The new settings are saved automatically. Y Output Shift: The controls in the Output Shift menu are similar to those in the Input Position menu, except that they change the characteristics of the output signal. These settings are saved independently for each aspect ratio. EL IM IN A R Image Alignment: The Image Alignment menu provides precise, nine-point control over the displayed image geometry. Use these controls as (and only if) needed to re-position the image corners, mid-points and center to eliminate “keystoning” (mis-aligned corners) or “pincushion” distortion (mid-points not aligned with corners). See Figure 4-8. Horizontal Keystoning PR Vertical Keystoning Pincushion Distortion Figure 4-8. Keystone and Pincushion Distortion Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 45 Operation To correct keystoning or pincushion distortion: 1. On the DHD Controller remote control or front panel, press MENU. 2. Select Calibration from the Main Menu and enter the Calibration Menu passcode. 3. Select Image Alignment from the Calibration Menu. 4. Select Corner Alignment to correct a “keystoned” image by adjusting the image corner positions. Select Midpoint Alignment to correct pincushion distortion by adjusting the image edge mid-points. See Figure 4-9. Use the built-in test pattern when adjusting the image corners or midpoints. To access it, check the Test Pattern box in the Corner Alignment or Midpoint Alignment menu. EL IM IN A R Y Tip Top Left (x, y) Top Middle (x, y) PR Left Middle (x, y) Top Right (x, y) Right Middle (x) Center (x, y) Bottom Left (x, y) Bottom Middle (y) Bottom Right (x, y) Notes: 1. Bottom Middle x = Top Middle x 2. Right Middle y = Left Middle y 3. Smaller “x” values move a point to the left; larger values move it to the right. 4. Smaller “y” values move a point up; larger values move it down. Figure 4-9. Image Alignment Controls Note The “Left Middle y” setting also controls the “Right Middle” y-coordinate. Similarly, the “Top Middle x” setting also controls the “Bottom Middle” x-coordinate. Splash Configure: Use the Splash Configure menu to control the appearance and behavior of the “splash” screen that appears on the display upon power-up. • Owner Name/ISF Calibrated/ISF Other: You can have the V-50HD/V-63HD display the owner’s name, your name, the phrase “ISF Calibrated” and/or any other string, up to 30 characters in length. Use the up or down cursor button to select a character. Use the right and left cursor buttons to change the cursor position. Press MENU when you have finished entering text. 46 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation • Splash Timer: When you turn on the V-50HD/V-63HD, it projects a welcome screen with the Runco and ISF logos, along with the personalized information you enter as described above. Select Splash Timer from the Splash Configure menu to set the amount of time for which this screen appears. The range is from 5 to 60 seconds, in one-second increments. Press or to set the timer, then press MENU. • Splash Enable: When you have finished customizing the splash screen, select Splash Enable from the Splash Configure menu. Then, select On and press ENTER. OSD Position: To adjust the position of the OSD, select OSD Position from the Calibration menu and press ENTER. or to select “Hor.” or “Ver.” Then, press or to change the position. Y Press Note EL IM IN A R Use the Service menu to access advanced display configuration settings. This menu should be used by ISF-certified technicians only. You must enter a passcode to access the Service menu. Service Service Test Video Input Names Display Device Network Test Video: Select Test Video from the Service Menu to access the internal test patterns on the DHD Controller. Table 4-3 lists the available test patterns and describes their suggested usage. Color Space Table 4-3. Test Patterns and Their Suggested Usage HDMI Pattern Suggested Usage Color Bars 1 PR Use this pattern when making color saturation and tint adjustments. Use this pattern when making color saturation and tint adjustments. Color Bars 2 Typically not used with flat-panel displays. Focus Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 47 Miscellaneous Sync Threshold Front Panel Brightness Auto Power Off Standby Mode System Reset Operation Table 4-3. Test Patterns and Their Suggested Usage Pattern Suggested Usage Use this pattern when making brightness, contrast or white balance (gain/offset) adjustments. Input Names Restore EL IM IN A R Press MENU to exit test pattern mode. C o mp o s i t e 1 Composite 1 C o mp o s i t e 2 Composite 2 C o mp o s i t e 3 Composite 3 C o mp o n e n t Component HD 1 HD 1 HD 2 HD 2 SCAR T SCART 1 HDMI 1 HDM I 2 HDMI 2 HDM I 3 HDMI 3 HDM I 4 HDMI 4 PR HDM I Y Grey Bars Input Names: You can give each input a descriptive name. For example, you may want to change the default input name to the type of source component connected to it: “VCR,” “DVD,” “Laptop” et cetera. Input names can be up to 12 characters long. To edit an input name, select Input Names from the Service menu. Press or to select an input and press ENTER. Use the or buttons to change a character; press or to select a character to change. When you have finished editing the input name, press ENTER or MENU. To restore the default input name, press “Restore” column. Then, press ENTER. repeatedly to highlight that input name in the Display Device - Configure: The options in the Display Device - Configure menu allow you to change the picture orientation or access other, display-device specific functions. • Installation – Orientation: Select Picture Orientation from the Display Device Configure menu, then select Orientation to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear). Or, use the Auto setting to have the display automatically determine the orientation (floor or ceiling) using an internal sensor. • Diagnostics: Select Diagnostics from the Display Device - Configure menu, then select Red, Green, Blue, Yellow, Cyan or Magenta to display only that color channel (simulating a filter of that color). This can be useful for calibration or measurement purposes. To restore the normal picture (all colors), select White. Network: The options in the Network menu allow you to configure the network communication features. • IP Configuration: Select IP Configuration from the Network menu to either set the IP address, subnet mask and default gateway of the DHD Controller manually or obtain these settings automatically, from a DHCP (Dynamic Host Configuration Protocol) server. (Most broadband routers and gateways support DHCP.) You can also test the network connection from this menu. 48 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation • DHCP: To enable the DHCP client in the DHD Controller, select DHCP from the IP Configuration menu and set it to On. With this setting, the DHD Controller’s IP address, subnet mask and default gateway are assigned by the local DHCP server. To manually configure these values, set DHCP to Off. The IP Address, Subnet Mask and Default Gateway items in the IP Configuration menu are disabled (grayed out) when DHCP is enabled. Note • IP Address: Select IP Address from the IP Configuration menu to manually configure the IP Address of the DHD Controller, as follows: or to select the first, second, third or fourth byte of the address. 2. Press or to set the value of that byte. The range is from 0 to 255 inclusive. EL IM IN A R Y 1. Press 3. Repeat Steps 1 and 2 for all four bytes of the address. 4. Press MENU when you have finished setting the address. • Subnet Mask: Select Subnet Mask from the IP Configuration menu to manually configure the IP subnet mask. The procedure is similar to that for setting the IP address. • Default Gateway: Select Default Gateway from the IP Configuration menu to manually configure the default IP gateway. The procedure is similar to that for setting the IP address. • Communication Test: Select Communication Test from the IP Configuration menu to verify proper operation of the network communication link. PR To start the test, select Start Test from the Communication Test menu. The DHD Controller displays the message “Performing Communication Test.” When the test completes, the DHD Controller displays either “Failed” (along with the error that occurred) or “Succeeded.” • Auto Firmware Upgrade: Select Auto Firmware Upgrade from the Network menu to enable automatic detection of a newer version of the DHD Controller firmware. If one is found, you can configure the DHD Controller to install it automatically. These features make it easier to keep your DHD Controller firmware up-to-date. • Auto Check For New Firmware: To have the DHD Controller automatically check for firmware updates at periodic intervals, select Auto Check for New Firmware from the Auto Firmware Upgrade menu and set it to On. If you prefer to do this manually, set it to Off and use the Check For New Firmware sub-menu (described below). • Auto Perform Upgrade: If the “Auto Check For New Firmware” process determines that a newer firmware version than the one currently installed is available, you can have the DHD Controller automatically download and install it. To do this, select Auto Perform Upgrade from the Auto Firmware Upgrade menu and set it to On. The upgrade will occur the next time the DHD Controller is “power-cycled” (powered off, then on again). If you prefer to do this manually, set it to Off. The DHD Controller will ask if you want to perform the upgrade the next time it is power-cycled. • Check For New Firmware: To have the DHD Controller check for new firmware on demand (and perform an upgrade if it finds a new version), select Check For New Firmware from the Auto Firmware Upgrade menu. If the DHD Controller finds a new firmware version, select Yes to perform the upgrade or No to return to the previous menu. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 49 Operation • E-Mail Notification: Select E-Mail Notification from the Network menu to specify when and to whom the DHD Controller sends error and service notification messages via e-mail. The notification messages are in the following format: To: [E-Mail Address; see below] From: [email protected] Subject: [Type of notification] from Runco DHD-LS Body: This is an automated message sent from the Runco DHD-LS: [One of the following: “DHD Error” / “Display Error” “Periodic Service Notification” “Calibration Data”] EL IM IN A R Y Notification: Detailed Description: [ If a DHD Error, one of the following: “Fan Failure 1” / “Fan Failure 2” “Overtemp 1” / “Overtemp 2” “Initialization Failure” If a Display Error, a device-specific error message If a Periodic Service Notification, the elapsed time since the last notification PR If a Calibration Data message, “See Attached File” ] Serial Number: [DHD Controller serial number] Customer Information: [From “Customer Information” sub-menu; see below] Best Regards, Runco International, LLC 1195 NW Compton Drive Beaverton, OR 97006 1-800-237-8262 • E-Mail Address: To specify the destination e-mail address for error and service notifications, select E-Mail Address from the E-Mail Notification menu. The procedure is similar to that for setting the IP address (refer to IP Configuration on page 48). Enter up to 45 alphanumeric characters. • Error Notification: To have the DHD Controller send a message to the destination e-mail address when a “DHD Error” or “Display Error” occurs, select Error Notification from the E-Mail Notification menu and set it to On. • Error Notification to Runco: To have the DHD Controller send an e-mail message to Runco Customer Support when a “DHD Error” or “Display Error” occurs, select Error Notification to Runco from the E-Mail Notification menu and set it to On. 50 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation • Periodic Service Notification: You can have the DHD Controller send periodic reminders via e-mail to perform regular maintenance tasks. To do this: 1. Select Periodic Service Notification from the E-Mail Notification menu. 2. Highlight Enable and press ENTER. 3. Highlight On and press ENTER. 4. Press MENU. 5. Highlight Timer and press ENTER. 6. Press or to set the notification interval in months. The range is from 1 to 255 inclusive; the default is 12 months. Y 7. Press MENU. 1. Press or repeatedly to select a line of text to edit. 2. Press ENTER. 3. Press or EL IM IN A R • Customer Information: Select Customer Information from the E-Mail Notification menu to supply this information to the DHD Controller, which includes it in all e-mail notification messages. Six lines (up to 30 characters per line) of text are provided; use them however you wish. repeatedly to set the highlighted character. 4. Press (or ) to select the next (or previous) character. Use the buttons to change it. and 5. Press ENTER when you have finished editing that line of text. 6. Repeat Steps 1 through 5 for each line of text you want to edit. 7. Press MENU when you have finished entering customer information. PR • E-Mail Calibration Data: To have the DHD Controller collect all calibration data, attach it to a message and send it to the destination e-mail address, select E-Mail Calibration Data from the E-Mail Notification menu. To confirm this action, select Yes and press ENTER. To cancel and return to the previous menu, select No. • Remote Network Control: Select Remote Network Control from the Network menu to enable or disable control of the DHD Controller via an IP connection (typically using a web browser). Set it to On to allow all incoming remote network connectivity. Set it to Off to disable any incoming network communication that was not initiated by the DHD Controller. Note This setting has no effect on the E-Mail Notification or Auto Firmware Upgrade functions. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 51 Operation Color Space: Select Color Space from the Service menu to choose the color space of the source signal for HDMI, RGB, and component connections. • The default setting, Auto, functions as follows: • HDMI: If the Auxiliary Video Information (AVI) infoframe contains color space and/or range data, the DHD Controller uses that information. Otherwise, for RGB sources, the DHD Controller uses the RGB-Video color space. For component SDTV and EDTV resolutions, REC601 is used. For other component video resolutions, REC709 is used. • RGB: If Hsync or Vsync signals are present, the DHD Controller uses the RGB-PC color space. Otherwise, REC601 is used for SDTV and EDTV sources, and REC709 for all other sources. EL IM IN A R Y • Component: For SDTV and EDTV resolutions, the DHD Controller uses the REC601 color space. For all other resolutions, REC709 is used. In most cases, the Auto setting determines the correct color space to use. If it does not, you can force the DHD Controller to use a specific color space. Choose one of the following: • REC709 sets the color space matrix to that defined in ITU-R BT.709. • REC601 sets the color space matrix to that defined in ITU-R BT.601. • RGB-PC uses RGB color space and sets black at 0,0,0 RGB and white at 255,255,255 RGB, assuming an 8-bit image. • RGB-Video uses RGB color space and sets black at 16,16,16 RGB and white at 235,235,235, assuming an 8-bit image, to correspond to the luminance values defined in digital component standards. PR Miscellaneous: Select Miscellaneous from the Service menu to set the following options: • Language: Select Language from the Miscellaneous menu and press the up- or down-arrows to select the OSD Language (English, Français, Deutsch, Italiano, Español, Svenska, (Simplified Chinese), (Traditional Chinese), Português, (Russian), (Japanese) or (Korean). • OSD Timer: Select OSD Timer from the Miscellaneous menu to set the OSD Timer, which controls how long the menus remain on-screen after selecting them. Select from 5 to 60 seconds, in one-second increments. Or, set the timer to 0 (disabled) if you want the menus to remain on-screen indefinitely. • OSD Messages: When you select a new aspect ratio, input source or memory preset, the DHD Controller briefly displays an on-screen message confirming your new selection. To prevent the display of these messages, select OSD Messages from the Miscellaneous menu to and set it to Off. • Blank Screen Color: Select Blank Screen Color from the Miscellaneous menu to select the color that appears when no incoming signal is present. The range is from 0 to 255 inclusive for each color component (red, green and blue). • Sidebar Color: Select Sidebar Color from the Miscellaneous menu to change the color of the inactive image area. The range is from 0 to 255 inclusive for each color component (red, green and blue). The inactive image area is on either side of the active image area when using the 4:3 aspect ratio. • Film Mode: Use Film Mode to smooth out moving images from interlaced, standard-definition (SD) sources. In most cases, the DHD Controller detects the proper “pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing you may want to enable Film Mode to ensure stable processing for that source. 52 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation • CUE (Chroma Upsampling Error) Correction: Some DVD players use MPEG decoders that do not correctly “upsample” the 4:2:0 format chroma information on the DVD to the 4:2:2 or 4:4:4 format required by the video encoder of the display device. This so-called “chroma bug” sometimes causes streaky or spiky horizontal lines running through the chroma channel. It is most noticeable in static, interlaced scenes and on diagonal edges (especially red ones). Set CUE to On to correct this issue. • Remote Code: Select Remote Code from the Miscellaneous menu to set the infrared (IR) code set to which the DHD Controller will respond. By default, it is set to 17. You can change this setting if either: Y • Another device in the theater (a DVD player, for example) is responding to commands from the DHD Controller remote control (Figure 2-6) in ways that are unpredictable or undesirable. Tip EL IM IN A R • You have multiple DHD Controllers and want to control them independently, as opposed to broadcasting commands from a single remote to all of them. In this scenario, you can use multiple remotes programmed to use different IR codes. Or, you can use a single remote and change the IR code as needed to address a specific DHD Controller. Use the serial command REMOTECODE [0 ... 31] to change the IR code to which the controller will respond (refer to Miscellaneous Commands on page 63). Then, change the code sent by the remote to match as described below. When you change a remote code on the DHD Controller, you must re-program the DHD Controller remote control to send that same code. To do this: PR 1. Press and hold the LIGHT button on the remote control for approximately three seconds, or until the LED on the remote lights solid red. 2. Enter a new two-digit code between 00 and 31 inclusive. Include a leading zero for single-digit codes; for example, enter 9 as “09.” LIGHT ON OFF 3. The LED turns off to confirm the code change. If you enter an invalid code, the LED flashes for three or four seconds. Try again, entering a valid code. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 53 Operation Sync Threshold: Select Sync Threshold to adjust the threshold at which negative pulses on the component video green/luma channel are interpreted to be sync pulses. Sync Threshold adjustment is occasionally necessary when a DVD player or HDTV source signal drops “below black” (for example, during scenes with explosions or when subtitles are present) and causes the display to temporarily lose sync. If the sync level from the source is persistently too low, the display device won’t sync with the source at all. The range is from 0 (approximately 60 millivolts (mV)) to 15 (approximately 300mV). HDMI: Select HDMI from the Service menu to set the following options affecting communication between HDMI sources, the DHD Controller and the V-50HD/V-63HD. EL IM IN A R Y • HDMI EDID Extension: Extended display identification data (EDID) is a data structure provided by a display device to describe its capabilities to a graphics card. It is what enables a modern personal computer to know what kind of monitor is connected. Some modern display devices provide more information via EDID than others, in the form of “extensions.” Some computer graphics cards do recognize or properly interpret this extended EDID information. Select HDMI EDID Extension from the HDMI menu to specify whether or not the EDID extensions from the display device are passed through to the sources connected to the HDMI 1, HDMI 2, HDMI 3 or HDMI 4 inputs. By default, the extensions are on. Change these settings only if HDMI EDID incompatibility issues arise. • Audio Format: Select Audio Format from the HDMI menu to choose an option for routing the audio signal from an HDMI source. With the V-50HD/V-63HD, the recommended setting is HDMI Out (Audio Only). (This is also the default setting.) PR • CEC: This control chooses whether or not the DHD Controller responds to HDMI CEC control messages from a disc player, set-top box or other HDMI source. It also enables or disables CEC communication between the DHD Controller and display. The default (and recommended) setting is On. For more information about CEC, refer to Using HDMI CEC Messages on page 68. Caution Do not set CEC to “Off” unless specifically instructed to do so by Runco Technical Support. If you do, the system will not work properly. Note The DHD Controller does not transmit HDMI CEC control messages from the “HDMI Audio Out” connector, regardless of the CEC setting. • HPD Toggle Rejection: Select HPD Toggle Rejection from the HDMI menu to specify whether or not the DHD Controller ignores extraneous Hot Plug Detect (HPD) signal state changes from a downstream HDMI device (third-party display or audio/video receiver). The default setting is Off. Set it to On when troubleshooting compatibility issues or to reduce the amount of time needed to lock to an incoming signal. 54 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Operation Front Panel Brightness: Select Front Panel Brightness from the Service menu to adjust the brightness of the front-panel LED status indicator. Logo LED Segment (Blue) Standby LED Segment (Yellow) Y • Logo LED: Select Logo LED from the Front Panel Brightness menu to adjust the brightness of the blue LED segment. The range is from 0 (off) to 31. During a firmware upgrade, this LED lights at full brightness regardless of the Logo LED setting. EL IM IN A R Note • Standby LED: Select Standby LED from the Front Panel Brightness menu to change the behavior of the yellow LED segment. When set to ON, the LED lights amber when the system is in standby mode; otherwise, it is off. When set to OFF, the LED is always off. Note During a firmware upgrade, this LED lights at full brightness regardless of the Standby LED setting. Auto Power Off: Select Auto Power Off from the Service menu to have the V-50HD/V-63HD turn itself off after a period of inactivity (no source signal present). PR • Enable: By default, Auto Power Off is disabled. To enable it, select Enable from the Auto Power Off sub-menu and set it to On. • Hours: The default time-out period is eight (8) hours; the range is from 1 to 24 hours. Standby Mode: Select Standby Mode from the Service menu to control the DHD Controller’s power management feature. • Choose Low Power (the default setting) to have the DHD Controller shut down completely when it is turned off. This conserves power but increases the amount of time required by the DHD Controller to start up when it is turned on. • Fast Startup is a “quick-start” mode that keeps the DHD Controller running when it is turned off even though it appears to be in standby mode. This allows for much quicker startup times but consumes more power. System Reset: To reset ALL controller settings (including image settings) back to their factory defaults, choose System Reset from the Service menu. A confirmation message appears. Select Yes to continue with the reset or select No to cancel. Caution This action is not undoable. Proceed with caution! Before you perform a System Reset, save your “Custom” Memory Presets (page 38) and ISF Day/Night Memory Presets (page 44). Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 55 Operation PR EL IM IN A R Y Notes: 56 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Maintenance and Troubleshooting 5. Maintenance and Troubleshooting Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the V-50HD/V-63HD. If the suggested solutions fail to resolve the problem or if you encounter an issue not described here, please contact Runco Technical Support. The system does not turn on. Possible Cause(s) Solution EL IM IN A R Symptom Y Table 5-1. Troubleshooting Chart • The V-50HD/V-63HD is not plugged in and switched on, or the AC outlet is not active. • The DHD Controller is not plugged in and switched on, or the AC outlet is not active. PR • The remote control batteries have run out. • The HDMI connection from the DHD Controller to the V-50HD/V-63HD is incorrect. • Ensure that the V-50HD/V-63HD is plugged in and switched on, and that the AC outlet is active. • Ensure that the DHD Controller is plugged in and switched on, and that the AC outlet is active. • Replace the batteries. • Ensure that the DHD Controller is properly connected to the V-50HD/V-63HD (see Figure 3-2). The display and DHD Controller are both on, but there is no picture and on-screen menus do not appear. • Faulty or incorrect video connection between the DHD Controller and the V-50HD/V-63HD. • Ensure that the HDMI output from the DHD Controller is properly connected to the PRIMARY INPUT on the V-50HD/V-63HD (see Figure 3-2). The display is on and menus appear, but there is no picture. • Incorrect source selection. • Source component is not turned on. • Source component is connected incorrectly or not at all. • Select the correct source. • Turn on the source component. • Check connections from source component to DHD Controller. A projected image from a DVD is split or otherwise scrambled. • DVD player is connected to the Component input and set to progressive scan mode. • Turn off progressive scan on the DVD player. Or, connect the DVD player to the HD1 or HD2 input. Image geometry is incorrect. • Incorrect aspect ratio selection. • Select a different aspect ratio. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 57 5.1 Troubleshooting Tips Maintenance and Troubleshooting Table 5-1. Troubleshooting Chart (continued) Symptom The display is jittery or unstable. Possible Cause(s) Solution • Poor-quality or improperly connected source. • Ensure that the source is properly connected and of adequate quality for detection. • Correct at the source. • The horizontal or vertical scan frequency of the input signal may be out of range for the display. Y • Contrast is set too high. EL IM IN A R Image is too bright and/or lacks definition in the bright areas of the image. • Lower the contrast setting. • Brightness is set too high. • Lower the brightness setting. Colors in the image are swapped; for example, reds appear blue or vice versa. • The Red/Pr, Green/Y or Blue/Pb outputs from the source are connected to the wrong inputs on the DHD Controller. • Ensure that the source outputs are connected to the correct DHD Controller input. PR Image appears “washed out” and/or dark areas appear too bright. 58 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual External Control 6. External Control In addition to using the DHD Controller remote control unit, there are three methods of controlling the V-50HD/V-63HD and DHD Controller externally: • Using a serial (RS-232) link to send ASCII commands and receive responses to those commands. • Using discrete infrared (IR) codes to program a third-party remote control unit. Y • Using an HDMI connection to send Consumer Electronics Control (CEC) commands from a BD player or other source component that supports CEC. EL IM IN A R The following sections describe these methods. The DHD Controller uses a simple text-based control protocol to take requests from control devices and to provide responses to such devices. This section describes how to send control messages over a serial link between the DHD Controller and an automation/control system or a PC running terminal emulation software. 6.1 Serial Communications Connect your control system or PC to the RS-232 input of the DHD Controller as shown in Figure 3-9. RS-232 Connection and Port Configuration Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to 19200, to match that of the DHD Controller RS-232 port. Serial commands to the DHD Controller take the following form: PR • Commands are not case-sensitive. • For a single command that takes no parameters, type the command followed by a carriage return; for example, to set the aspect ratio to Letterbox, type LETTERBOX <Enter>. • For a single command that takes a parameter, type the command, a space or a comma and the desired value followed by a carriage return; for example, to set the brightness to -10, type BRIGHTNESS -10 <Enter> or BRIGHTNESS,-10 <Enter>. • You can also send a string of multiple commands on a single line, separated by commas. For example, COMPOSITE,BRIGHTNESS 50,16:9 <Enter> switches to the Composite video input, sets the brightness to 50 and sets the aspect ratio to 16:9. Command strings can be up to 255 characters long. Note Avoid combining the ON or POWER 1 commands with other commands on a single line. After sending ON or POWER 1, allow at least five (5) seconds for the DHD Controller to power up. If you have enabled the ISF splash screen (refer to Splash Configure on page 46), allow 15 seconds for the DHD Controller to power up. Once it does, it will accept and properly execute multiple serial commands. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 59 Serial Command Syntax External Control Table 6-1 lists the RS-232 command set. The “Parameter (min/max)” column shows the valid parameter ranges, or “NA” for commands that take no parameters. When you enter a valid command, the DHD Controller executes it and acknowledges it with a plus sign on the command line (+ >). When you enter an invalid command – one that is misspelled or followed by values outside the valid range for that command – the DHD Controller ignores it and returns a minus sign (- >). Table 6-1. Serial Commands Command Parameter (min/max) Value Stored? Description NA NA EL IM IN A R OFF Y Power On/Off Commands Turns display off ON NA NA Turns display on POWER 0/1 NA Turns display on and off POWER? NA NA Returns power status PR Input Selection Commands COMPONENT NA YES Selects the Component input COMPOSITE or COMPOSITE1 NA YES Selects the Composite 1 video input COMPOSITE2 NA YES Selects the Composite 2 video input COMPOSITE3 NA YES Selects the Composite 3 video input HDMI1 NA YES Selects the HDMI 1 input HDMI2 NA YES Selects the HDMI 2 input HDMI3 NA YES Selects the HDMI 3 input HDMI4 NA YES Selects the HDMI 4 input HD1 NA YES Selects the RGB HD 1 input HD2 NA YES Selects the RGB HD 2 input INPUT? NA NA Returns active input SCART NA YES Selects the SCART input 60 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual External Control Table 6-1. Serial Commands (continued) Command Parameter (min/max) Value Stored? Description Aspect Ratio Commands NA YES Selects the 16:9 aspect ratio 4:3 NA YES Selects the 4:3 aspect ratio ASPECT? NA NA Returns current aspect ratio CINEMA NA YES Selects the Cinema aspect ratio LETTERBOX NA YES Selects the Letterbox aspect ratio NATIVE NA YES Selects the Native aspect ratio VIRTUALWIDE NA YES Selects the VirtualWide aspect ratio VIRTUALCINEMA NA YES Selects the Virtual Cinema aspect ratio EL IM IN A R Y 16:9 Picture Adjust Commands -50/50 YES Sets a value for brightness BRIGHTNESS? NA NA Returns brightness setting value CHROMADELAY -7/7 YES Sets a value for input color chroma delay CHROMADELAY? NA NA Returns input color chroma delay setting COLOR -50/50 YES Sets a value for color COLOR? NA NA Returns color setting value CONTRAST -50/50 YES Sets a value for contrast NA NA Returns contrast setting value 0/1 YES Sets Film Mode off (0) or on (1) NA NA Returns Film Mode setting (0 = off; 1 = on) FILTER 0/10 YES Sets a value for input color noise filter FILTER? NA NA Returns input color noise filter setting PHASE 0/31 YES Adjusts phase PHASE? NA NA Returns phase setting value SHARPNESS -50/50 YES Sets a value for sharpness SHARPNESS? NA NA Returns sharpness setting value TINT -50/50 YES Sets a value for tint TINT? NA NA Returns tint setting value CONTRAST? FILMMODE FILMMODE? PR BRIGHTNESS Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 61 External Control Table 6-1. Serial Commands (continued) Command Parameter (min/max) Value Stored? Description Image Preset Commands NA YES Loads “Custom 1” image preset CUSTOM2 NA YES Loads “Custom 2” image preset DAY NA YES Loads “ISF Day” image preset NIGHT NA YES Loads “ISF Night” image preset PRESET? NA NA EL IM IN A R Y CUSTOM1 Returns currently-selected preset (ISF Day, ISF Night, Custom 1 or Custom 2) PR Input Position Commands IHEIGHT 0/20 YES Sets the value for input height IHEIGHT? NA NA Returns input height value IHPOS -50/50 YES Sets a value for horizontal input position IHPOS? NA NA Returns input horizontal position value IVPOS -50/50 YES Sets a value for vertical input position IVPOS? NA NA Returns input vertical position value IWIDTH 0/50 YES Sets the value for input width IWIDTH? NA NA Returns input horizontal width value OVERSCAN 0/20 YES Sets the overscan percentage OVERSCAN? NA NA Returns overscan percentage OVERSCANMODE 0/1 YES Sets the overscan mode (0=zoom; 1=crop) OVERSCANMODE? NA NA Returns the overscan mode (0=zoom; 1=crop) Output Shift Commands OHEIGHT -50/50 YES Sets the value for output height OHEIGHT? NA NA Returns output height value OHPOS -50/50 YES Sets the value for output horizontal position OHPOS? NA NA Returns output horizontal position value OVPOS -50/50 YES Sets the value for output vertical position OVPOS? NA NA Returns output vertical position value OWIDTH -50/50 YES Sets the value for output width OWIDTH? NA NA Returns output horizontal width value 62 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual External Control Table 6-1. Serial Commands (continued) Command Parameter (min/max) Value Stored? Description Sleep Timer Commands NA NA Returns sleep timer setting STOFF NA YES Sets the sleep timer to Off ST30MIN NA YES Sets the sleep timer to 30 minutes ST60MIN NA YES Sets the sleep timer to 60 minutes ST90MIN NA YES Sets the sleep timer to 90 minutes ST2HRS NA YES Sets the sleep timer to 2 hours ST4HRS NA YES Sets the sleep timer to 4 hours EL IM IN A R Y SLEEPTMR? Screen Commands SCREEN? NA SCREEN1 NA SCREEN2 NA NA Returns the screen setting NA Sets the screen to Screen 1 NA Sets the screen to Screen 2 Miscellaneous Commands NA NA Returns display device input source value, as follows: 1 = Auto 52 = V-50HD 53 = V-63HD INRES? NA NA Returns input resolution NA NA Returns DHD Controller MAC address NA NA Returns product model name NA NA Returns output resolution REMOTECODE 0/31 YES Sets the remote code REMOTECODE? NA NA Returns the remote code SERNUM? NA NA Returns DHD Controller serial number SWVER? NA NA Returns software version number SYSSTATE? 0/4 NA Returns current system state 0 = Off 1 = Initializing 2 = On 3 = Powering Down 4 = Error MACADDR? MODEL? OUTRES? PR DISPLAY? Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 63 External Control Table 6-1. Serial Commands (continued) Command Parameter (min/max) Value Stored? Description The following serial commands are meant to emulate buttons on the remote control. Each button has its own serial command, so effectively it is as if you were using the IR remote only you’ll be doing so via serial commands. These commands provide active OSD responses just like the IR remote. NA Down-Arrow ( ENTER NA NA ENTER key EXIT NA NA EXIT key LEFT NA NA MENU NA NA MENU RIGHT NA NA Right-Arrow ( UP NA NA Up-Arrow ( Y NA EL IM IN A R 6.2 Using Discrete IR Codes DOWN Left-Arrow ( ) key ) key ) key ) key The DHD Controller accepts commands in the form of IR signals that conform to the Phillips RC5 protocol. Each DHD Controller remote control button has an RC5 control code associated with it. PR You can use these codes to program a third-party, “universal” remote control unit to work with the DHD Controller. These third-party products usually come with a computer software application for this purpose. For more information, consult the documentation provided with the remote control unit. IR Command Protocol ➤ The IR control codes have the following characteristics: • Each code consists of 14 bits: • Two (2) start bits (always 1); • A toggle bit. This bit is inverted every time a key is released and pressed again. This allows the DHD Controller to distinguish between a button that remains down and one that is pressed repeatedly. • Five (5) address bits. The default address is 17 (binary 10001). To change it, select Remote Code from the Miscellaneous menu (in the Service menu) and follow the steps given on page 53. • Six (6) data bits. • The carrier frequency is 36 kHz, with the modulated pulses having a 25% duty cycle. • Commands are sent at a maximum rate of 9 Hz. 64 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual External Control For example, here is the RC5 control code for the ON button on the DHD Controller remote control unit (assuming the default address is used): With Toggle Bit = 0 Hex Binary 3 1 4 1 0 4 1 0 0 0 1 1 0 0 0 0 0 1 0 1 With Toggle Bit = 1 1 C 1 1 Start Bits Function 4 1 0 Toggle Bit 0 0 1 1 0 0 0 0 Y Binary 3 Address Command EL IM IN A R Hex Figure 6-1 shows the pulse train for this command (with the toggle bit set to zero). Data Word S1 S2 TB A4 Start Bits Toggle Bit Encoded Data Word 1 1 0 1.78 ms A2 A1 A0 C5 C4 Address Bits 0 0 0 C3 C2 C1 C0 0 1 Command Bits 1 0 0 0 0 PR Modulated Carrier 1 A3 Zoom In of Carrier 27.8 µs tp 3t p First Packet Repeated Packet RC5 Packet Transmission 14 cycles, 24.9 ms 64 cycles, 113.8 ms Figure 6-1. RC5 Message Format Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 65 External Control IR Command List ➤ Table 6-2 lists the RC5 control codes for the DHD Controller. Table 6-2. RC5 Control Codes for the DHD Controller Remote Control Button Name RC5 Data from Remote Control (Note) RC5 Data with Toggle Bit = 1 (Note) 0x3449 0x3C49 16:9 aspect ratio 4:3 0x344A 0x3C4A 4:3 aspect ratio CINEMA 0x346C 0x3C6C Cinema aspect ratio COMP 0x344E 0x3C4E Component video input CUST 1 0x3472 0x3C72 Custom 1 memory preset CUST 2 0x3473 0x3C73 Custom 2 memory preset DOWN 0x3446 0x3C46 Down-Arrow ( ENTER 0x3444 0x3C44 ENTER EXIT 0x3474 0x3C74 EXIT HD 1 0x3451 0x3C51 HD1 video input HD 2 0x3452 0x3C52 HD2 video input HDMI 1 0x3453 0x3C53 HDMI1 video input HDMI 2 0x3454 0x3C54 HDMI2 video input HDMI 3 0x3455 0x3C56 HDMI3 video input HDMI 4 0x3456 0x3C56 HDMI4 video input ISF DAY 0x3471 0x3C71 ISF Day memory preset ISF NT 0x3470 0x3C70 ISF Night memory preset LEFT 0x3447 0x3C47 Left-Arrow ( LET BOX 0x344B 0x3C4B Letterbox aspect ratio MENU 0x3443 0x3C43 MENU NATIVE 0x346E 0x3C6E Native aspect ratio OFF 0x3442 0x3C42 Power off ON 0x3441 0x3C41 Power on RIGHT 0x3448 0x3C48 Right-Arrow ( SCART 0x3457 0x3C57 SCART video input STOFF 0x3460 0x3C60 Sets the sleep timer to Off ST30MIN 0x3461 0x3C61 Sets the sleep timer to 30 minutes Y 16:9 EL IM IN A R PR Description ) ) ) Note: These codes assume that the default address of 17 is used. If you change it to something other than 17, you will need to modify these codes accordingly. 66 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual External Control Table 6-2. RC5 Control Codes for the DHD Controller (continued) Remote Control Button Name RC5 Data from Remote Control (Note) RC5 Data with Toggle Bit = 1 (Note) Description 0x3462 0x3C62 Sets the sleep timer to 60 minutes ST90MIN 0x3463 0x3C63 Sets the sleep timer to 90 minutes ST2HRS 0x3464 0x3C64 Sets the sleep timer to 2 hours ST4HRS 0x3465 0x3C65 Sets the sleep timer to 4 hours UP 0x3445 0x3C45 Up-Arrow ( VID 1 0x344D 0x3C4D Composite video input 1 VID 2 0x3458 0x3C58 Composite video input 2 VID 3 0x3459 0x3C59 Composite video input 3 V-CINE 0x346D 0x3C6D Virtual Cinema aspect ratio V-WIDE 0x344C 0x3C4C VirtualWide aspect ratio EL IM IN A R ) Y ST60MIN PR Note: These codes assume that the default address of 17 is used. If you change it to something other than 17, you will need to modify these codes accordingly. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 67 External Control 6.3 Using HDMI CEC Messages The DHD Controller accepts and can respond to CEC command messages from a disc player, satellite receiver or DVR/set-top box via an HDMI connection. Using CEC, the DHD Controller can perform the following actions: • Turn itself and the display device on and select the correct input when the source component initiates playback of a disc or recorded program. • Turn the source component on when you switch to its corresponding input on the DHD Controller. • Turn the source component off when the DHD Controller is turned off (unless the source component is in playback mode). Y • Change its OSD language when a similar change is made at the source. EL IM IN A R To use CEC, connect your CEC-compatible sources to the HDMI inputs on the V-50HD/V-63HD. Set the CEC option to On (refer to CEC on page 54). Additional steps may be needed to enable CEC at the source. Refer to the documentation for your source device for more information. CEC Command List ➤ Table 6-3 lists the CEC commands supported by the DHD Controller. Table 6-3. CEC Commands Supported by the DHD Controller PR Opcode Initiator Follower Feature Abort 0x00 √ √ Standby 0x36 √ √ Routing Change 0x80 √ √ Routing Information 0x81 √ √ Active Source 0x82 √ √ Request Active Source 0x85 √ √ Device Vendor ID 0x87 √ √ Give Device Vendor ID 0x8C √ √ Vendor Command With ID 0xA0 √ √ Polling Message N/A √ √ Text View On 0x0D √ – Report Physical Address 0x84 √ – Inactive Source 0x9D √ – CEC Version 0x9E √ – Set OSD Name 0x47 √ – Menu Status 0x8E √ – Report Power Status 0x90 √ – Set Menu Language 0x32 – √ 68 Downloaded From TV-Manual.com Manuals Supported? (√ = Yes, – = No) Value Vistage™ Series Flat-Panel Display Installation/Operation Manual External Control Table 6-3. CEC Commands Supported by the DHD Controller (continued) Supported? (√ = Yes, – = No) Opcode Value Initiator Follower 0x83 – √ Set Stream Path 0x86 – √ Get CEC Version 0x9F – √ Abort Message 0xFF – √ User Control Pressed 0x44 – √ User Control Released 0x45 – √ Give OSD Name 0x46 – √ Menu Request 0x8D – √ Give Device Power Status 0x8F – √ EL IM IN A R The DHD Controller does not transmit HDMI CEC control messages from the “HDMI Audio Out” connector. PR Note Y Give Physical Address Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 69 External Control PR EL IM IN A R Y Notes: 70 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Specifications 7. Specifications 7.1 V-50HD/V-63HD Specifications Table 7-1 lists the V-50HD/V-63HD specifications. Full HD 1920 x 1080 (1080p) Diagonal Size: V-50HD - 50 inches V-63HD - 63 inches Aspect Ratios: Refer to Table 7-2 DTV Compatibility: Processing: EL IM IN A R Native Resolution: Y Table 7-1. V-50HD/V-63HD Specifications Refer to Table 7-3 Runco DHD-LS Processor with ViVix IV™ technology and BRiC (Backup, Recovery and Clone) tool Control Options: • Serial commands via RS-232 • Discrete infrared (IR) remote • Consumer Electronics Control (CEC) protocol support via HDMI • Ethernet Inputs: Refer to Table 7-2 Video Standards: NTSC, PAL, SECAM, CEA-861D Calibration: ISF Certified Calibration Configuration 1,000,000:1 typical; 10,000:1 minimum PR Contrast Ratio (sequential): Power Requirements: 100 VAC to 240 VAC +/- 10% @ 50/60Hz Power Consumption: V-50HD - 400W maximum; 1W standby V-63HD - 625W maximum; 1W standby Operating Temperature: 10°C to 40°C, up to 9,100 feet altitude Operating Humidity: 20 - 80% humidity (non-condensing) Dimensions: V-50HD - See Figure 7-1 V-63HD - See Figure 7-2 Weight: V-50HD - 75 lbs. (34.0 kg) V-63HD - 125 lbs. (56.7 kg) Regulatory Approvals: FCC Class B, CE, C-Tick Limited Warranty: Two (2) years parts and labor from the date of shipment from Runco. Extended RuncoCare™, Runco Red Carpet™ and PremierCare™ plans also available. Specifications are subject to change without notice. Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 71 Specifications 7.2 DHD Controller Specifications Table 7-2 lists the DHD Controller specifications. Table 7-2. DHD Controller Specifications Aspect Ratios: 4:3, Letterbox, 16:9, VirtualWide, Cinema, Virtual Cinema, Native Video Standards: • • • • • • • • (4) HDMI with CEC and Deep Color (1) Component/SCART (3 x RCA) (2) Component/RGBHV (5 x BNC) (3) Composite (1) HDMI with Deep Color to V-50HD/V-63HD (1) HDMI with Deep Color to second display or audio processor • Discrete infrared (IR) remote • RS-232 (female DB9) for serial commands • Consumer Electronics Control (CEC) protocol support via HDMI • Ethernet EL Control Options: PR Y A R IM IN Inputs: Outputs: HDMI and DVI with HDCP for digital video Component and RGB HDTV (1080p, 1080i, 720p) Component and RGB EDTV (576p, 480p) Component and Composite SDTV (576i, 480i) RGB SCART with adaptor NTSC (M, 4.43) PAL (B, G, H, I, N, M) SECAM (M) Ethernet Communication: RJ45 (female) for web server, e-mail, auto firmware upgrade and Telnet RS-232 Communication Parameters: 19200 bps, no parity, 8 data bits, 1 stop bit, no flow control Accessory Applications: Runco Firmware Upgrader, Runco BRiC (backup, restore, clone), CalMAN by SpectraCal for automatic calibration Power Requirements: 100-240V~, 47-63Hz, 0.45 Amps Operating Environment: 41°F to 104°F (5°C to 40°C), 0% to 90% humidity (non-condensing); up to 10,000 feet (3,048 meters) altitude Dimensions: Width = 17.50 inches (444.5 mm) Depth = 11.19 inches (284.1 mm) Height = 3.75 inches (95.3 mm) Weight: 15.4 lbs. (7.00 kg) Regulatory Approvals: cTUVus, FCC class B, CE, RoHS, China RoHS, WEEE, C-Tick, CCC, local conformances as required Limited Warranty: Two (2) years parts and labor from the date of shipment from Runco. Specifications are subject to change without notice. 72 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Specifications 7.3 V-50HD Dimensions Figure 7-1 shows the V-50HD dimensions. 30.4in 773.2mm 31.6in 802.7mm EL IM IN A R 49.5in 1257mm Speaker Bar 8.3in 210.1mm 17.0in 432.3mm Note: Speaker bar mounts to display via mounting brackets (x2). PR 30.4in 773.2mm Y 4.5in 114.3mm Audio Input Figure 7-1. V-50HD Dimensions (with Optional Speaker Bar) Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 73 Specifications 7.4 V-63HD Dimensions Figure 7-2 shows the V-63HD dimensions. 4.5in 114.3mm 36.8in 935.2mm 31.6in 802.7mm A R Y 60.9in 1547.4mm IN Rubber feet (x4) 8.2in 208mm 17.0in 432.3mm 36.8in 935.2mm Note: Speaker bar mounts to display via mounting brackets (x2). PR EL IM 43.0in 1092.5mm Audio Input Figure 7-2. V-63HD Dimensions (with Optional Speaker Bar) 74 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Specifications 7.5 Supported Timings Table 7-3 lists the signal types supported by each input on the DHD Controller. Table 7-3. Supported Signal Timings by Input 640x480 800x600 640x480 800x600 832x624 848x480 848x480 1024x768 25.175 √ Composite 1 Composite 2 Composite 3 31.469 SCART 60.00 Component Pixel Frequency (MHz) √ √ – – HDMI 1 HDMI 2 HDMI 3 HDMI 4 Horizontal Frequency (kHz) 66.59 35.892 29.862 √ √ √ – – 72.00 37.861 31.500 √ √ √ – – 75.00 37.500 31.500 √ √ √ – – 85.00 43.269 36.000 √ √ √ – – 60.00 37.879 40.000 √ √ √ – – 72.00 48.077 50.000 √ √ √ – – 75.00 46.875 49.500 √ √ √ – – 85.00 53.674 56.250 √ √ √ – – 74.54 52.849 60.036 √ √ √ – – 47.95 25.270 27.089 √ √ √ – – 60.00 31.020 33.750 √ √ √ – – 60.00 48.363 65.000 √ √ √ – – 70.00 56.476 75.000 √ √ √ – – 75.00 60.023 78.750 √ √ √ – – 85.00 68.677 94.500 √ √ √ – – PR 832x624 Refresh Rate (Hz) Y Resolution EL IM IN A R Format HD 1 HD 2 Supported? (√ = Yes, – = No) 1024x768 1152x864 1152x864 75.00 67.500 108.000 √ √ √ – – 1280x720 1280x720 47.95 37.833 64.769 √ √ √ – – 60.00 47.396 68.250 √ √ √ – – 60.00 47.776 79.500 √ √ √ – – 75.00 60.289 102.250 √ √ √ – – 85.00 68.633 117.500 √ √ √ – – 60.00 60.000 108.000 √ √ √ – – 85.00 85.938 148.500 √ √ √ – – 1280x768 1280x960 1280x768 1280x960 Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 75 Specifications Table 7-3. Supported Signal Timings by Input (continued) HDMI 1 HDMI 2 HDMI 3 HDMI 4 Component SCART Composite 1 Composite 2 Composite 3 1400x1050 Pixel Frequency (MHz) 60.00 63.981 108.000 √ √ √ – – 75.00 79.976 135.000 √ √ √ – – 85.00 91.146 157.500 √ √ √ – – 60.00 47.712 85.500 √ √ √ – – 60.00 64.744 101.000 √ √ √ – – 60.00 65.317 121.750 √ √ √ – – 75.00 82.278 156.000 √ √ √ – – 162.000 √ √ √ – – 119.000 √ √ √ – – 56.821 150.007 √ √ √ – – 74.038 154.000 √ √ √ – – 1600x1200 60.00 75.000 1680x1050 1680x1050 60.00 64.674 1920x1080 1920x1080 47.95 1920x1200 1920x1200 60.00 SCART RGBS – 480/60i 720x487 480/60p 720x483 576/50i IM 1600x1200 EL 1400x1050 1360x768 Horizontal Frequency (kHz) Y 1360x768 1280x1024 Refresh Rate (Hz) A R 1280x1024 Resolution IN Format HD 1 HD 2 Supported? (√ = Yes, – = No) – – – – – √ – 59.94 15.734 13.500 √ √ √ – – 59.94 31.469 27.000 √ √ √ – – 720x576 50.00 15.625 14.750 √ √ √ – – 576/50p 720x576 50.00 31.250 29.000 √ √ √ – – 720/24p 1280x720 59.341/59.400 √ √ √ – – 720/25p 1280x720 74.250 √ √ √ – – 720/30p 1280x720 74.175/74.250 √ √ √ – – 720/50p 1280x720 50.00 37.500 75.250 √ √ √ – – 720/60p 1280x720 60.00 45.000 74.250 √ √ √ – – 1080/50i 1920x1080 50.00 28.125/31.250 74.250/72.000 √ √ √ – – 1080/60i 1920x1080 59.94/60.00 33.716/33.750 74.175/74.250 √ √ √ – – 1080/24p 1920x1080 23.98/24.00 26.978/27.000 74.175/74.250 √ √ √ – – 1080/50p 1920x1080 148.500 √ √ √ – – 1080/60p 1920x1080 59.94/60.00 67.433/67.500 148.350/148.500 √ √ √ – – PR 50.00 23.98/24.00 17.982/18.000 25.00 18.750 29.97/30.00 22.478/22.500 50.00 56.250 NTSC 3.58 – 59.94/60.00 15.734/15.750 3.580 – – – – √ NTSC 4.43 – 59.94/60.00 15.734/15.750 4.430 – – – – √ PAL-B/G/H/I – 4.430 – – – – √ 50.00 15.625 76 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Specifications Table 7-3. Supported Signal Timings by Input (continued) PAL-N – 50.00 SECAM – 50.00 Composite 1 Composite 2 Composite 3 – SCART PAL-M Component Resolution HDMI 1 HDMI 2 HDMI 3 HDMI 4 Refresh Rate (Hz) Format HD 1 HD 2 Supported? (√ = Yes, – = No) 3.580 – – – – √ 15.625 3.580 – – – – √ 15.625 13.500 – – – √ √ Horizontal Frequency (kHz) PR EL IM IN A R Y 59.94/60.00 15.734/15.750 Pixel Frequency (MHz) Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 77 Specifications PR EL IM IN A R Y Notes: 78 Downloaded From TV-Manual.com Manuals Vistage™ Series Flat-Panel Display Installation/Operation Manual Downloaded From TV-Manual.com Manuals 020-1114-00 Rev. A April 2011 Runco International • (800) 23RUNCO • Fax (503) 748-8161 • www.runco.com Downloaded From TV-Manual.com Manuals
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project