ProForm | 775 CT PFTL72707.0 | User`s manual | ProForm 775 CT PFTL72707.0 User`s manual

Model No. PFTL72707.0
Serial No.
USER'S MANUAL
Write the serial number in the
space above for future reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete customer satisfaction. If you have
questions, or if parts are missing,
PLEASE DO NOT CONTACT
THE STORE; please contact
Customer Care.
IMPORTANT: You must note the
product model number and
serial number (see the drawing
above) before contacting us:
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MST
Sat. 8 a.m.–4 p.m. MST
ON THE WEB:
www.proformservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
The decals shown here have been applied in the
locations shown. If a decal is missing or illegible,
call the telephone number on the front cover of
this manual and request a free replacement
decal. Apply the decal in the location shown.
Note: The decals may not be shown at actual size.
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons
with pre-existing health problems.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 10. To purchase a surge suppressor, see
your local PROFORM dealer or call the telephone number on the front cover of this manual and order part number 146148, or see your
local electronics store.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
13. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Keep the power cord and the surge suppressor away from heated surfaces.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 21 if the treadmill is
not working properly.)
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
8. The treadmill should be used only by persons
weighing 300 lbs. (136 kg) or less.
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 12).
9. Never allow more than one person on the
treadmill at a time.
17. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. When connecting the power cord (see page
10), plug the power cord into a surge suppressor (not included) and plug the surge
suppressor into a grounded circuit capable of
3
20. Use the included dumbbells only as described in this manual. Properly store the
dumbbells in the dumbbell holders on the
console when you are not using them (see the
drawing on page 5). If the dumbbells are improperly stored, they may fall off the console,
causing the user to trip.
23. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
24. Never insert any object into any opening on
the treadmill.
25. Inspect and properly tighten all parts of the
treadmill regularly.
21. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off circuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
26.
DANGER: Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the maintenance and adjustment procedures described in
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
22. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 19.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
27. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
SAVE THESE INSTRUCTIONS
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
775 CT CROSSTRAINER treadmill. The 775 CT
CROSSTRAINER treadmill offers an impressive array
of features designed to make your workouts at home
more enjoyable and effective. And when you’re not exercising, the unique 775 CT CROSSTRAINER treadmill can be folded up, requiring less than half the floor
space of other treadmills.
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.proformservice.com/registration.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after reading this manual, please see the front cover of this man-
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Fan
Console
Dumbbell/Water Bottle Holder*
Key/Clip
Handgrip Pulse Sensor
Handrail
Upright
Walking Belt
Reset/Off
Circuit Breaker
Power Cord
Foot Rail
Cushioned Walking Platform
Rear Roller
Adjustment Bolts
*Water bottle is not included
5
Star Washer
(106)–4
Washer (38)–4
2 1/2” Bolt (37)–2
ASSEMBLY
technician
1-800-445-2480.
To hire an authorized service
Wheel
Nut (32)–2 Assembly requires
(45)–4 to assemble the treadmill, call
3 1/2” Bolt
two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing
materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking
Handrailbelt
Boltor(64)–4
the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on
top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1" Tek Screw (83)–4
Assembly requires the included hex key and your own Phillips screwdriver
(with a
shaft at least 6" long) and wire cutters
.
Star Washer
Extension
Leg Bolt
(96)–4
Use the drawings below to identify the assembly hardware. The number in parentheses
below each
drawing
is
(84)–2 the key number of the part, from the PART LIST near the end of the manual. The number after the parentheses
Wheel Nut (13)–2
Extension Leg Bolt (96)–4
shows the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic
parts, do not use power tools for assembly.
Extension Leg Nut (67)–4
3/4" Screw (22)–4
Latch Shock
Nut (30)–2
Star Washer (8)–4
Upper Latch Shock Bolt (50)–1
Ground Screw
(33)–1
Screw (3)–9
Lower Latch Shock Bolt (39)–1
Handrail Bolt (64)–4
Base Leg Bolt (65)–4
1. Make sure that the power cord is unplugged.
1
84
With the help of a second person, carefully tip
the treadmill onto its left side as shown.
65
82
Insert an Extension Leg (89) into the base of the
Uprights (84) as shown. Hold two Extension Leg
Nuts (67) in the bottom of the Extension Leg.
Next, insert two Base Leg Bolts (65) into the top
of the Extension Leg, and firmly tighten the
Base Leg Bolts into the Extension Leg Nuts.
82
89
Attach two Base Pads (82) to the base of the
Uprights (84) with two 3/4" Tek Screws (22).
6
67
22
22
2. With the help of a second person, carefully tip
the treadmill onto its right side as shown.
2
84
Insert the other Extension Leg (89) into the base
of the Uprights (84) as shown. Hold two
Extension Leg Nuts (67) in the bottom of the
Extension Leg. Next, insert two Base Leg Bolts
(65) into the top of the Extension Leg, and firmly
tighten the Base Leg Bolts into the Extension
Leg Nuts.
65
82
82
22
58
Attach two Base Pads (82) to the base of the
Uprights (84) with two 3/4" Tek Screws (22).
67
89
With the help of a second person, carefully raise
the treadmill so that all four Base Pads (82) are
on the floor and the Frame (58) is in a vertical
position (see the drawing in step 4).
3. Identify the Storage Latch (29). Remove the tie
from the end of the tube. Make sure that the
sleeve has been slid over hole 1 and that the
Latch Knob (97) is locked into hole 1. Pull on
the sleeve to make sure that it is locked into
place.
3
97
Hole 1
Tube
29
Sleeve
4. Orient the Latch Assembly (29) so that the large
barrel and the Latch Knob (97) are positioned as
shown. Attach the lower end of the Latch
Assembly to the bracket on the Upright (84) with
the Lower Latch Shock Bolt (39) and a Latch
Shock Nut (30).
4
58
30
Then, attach the upper end of the Latch
Assembly (29) to the bracket on the Frame (58)
with the Upper Latch Shock Bolt (50) and a
Latch Shock Nut (30). Note: It may be necessary to move the Frame back and forth to align
the Latch Assembly with the bracket.
50
29
97
Large
Barrel
84
30
39
7
5. Lower the Frame (not shown) (see HOW TO
LOWER THE TREADMILL FOR USE on page
20).
5
64
Have a second person hold the Handrail (20)
near the Uprights (84). Insert the Wire Harness
(77) into the hole in the bottom of the Handrail
and out of the top as shown.
8
20
64
8
Next, set the Handrail (20) on the Uprights (84).
Do not let the Wire Harness (77) fall into the
right Upright.
77
Attach the Handrail (20) with four Handrail Bolts
(64) and four Star Washers (8); start all four
Handrail Bolts and then firmly tighten them.
84
84
6. While a second person holds the console assembly near the Handrail (20), attach the
ground wire to the indicated hole in the Handrail
with a Ground Screw (33).
6
Console
Assembly
Ground
Wire
33
Hole
20
7. While the second person continues to hold the
console assembly, locate the wire harness underneath the console assembly.
7
Connect the wire harness from the console assembly to the Wire Harness (77). See the inset
drawing. The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap
into place, turn one connector and then try
again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
TURNED ON. Then, insert the connectors
downward into the Handrail (20).
Wire Harness
Console
Assembly
77
20
8
77
8. Set the console assembly on the Handrail (20).
Be careful to avoid pinching any of the
wires. Make sure that the ground wire (see
step 6) and the wire harness from the console assembly (see step 7) are in the indicated channel.
8
Console Assembly
Channel
Hand tighten five Screws (3) into the Handrail
(20) and the console assembly. Start all five
Screws, but do not tighten them yet. Do not
put Screws into the two indicated holes.
20
3
3
3
No Screws
9. Hand tighten four additional Screws (3) into the
Handrail (20) and the console assembly. Then,
tighten all nine Screws used in step 8 and
this step; do not overtighten the Screws.
9
Console Assembly
3
20
3
10. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used
to adjust the walking belt (see pages 22 and 23).
If you purchase the optional chest pulse sensor (see page 18), follow the steps below to install the receiver
included with the chest pulse sensor.
1. Remove the key from the console and unplug
the power cord.
85
Remove the Screw (3) and the Access Door
(76) from the back of the Console Base (85).
2. Connect the wire on the receiver (A) to the indicated wire extending from the Console Base
(85). Hold the receiver so the small cylinder
is oriented as shown and is facing the
Console Base. Attach the receiver to the plastic
posts on the Access Door (76) with the two included small screws.
Small Screws
Wire
A
Small
Cylinder
3. Make sure that no wires are pinched.
Reattach the Access Door (76) with the Screw
(3). Discard the other wires included with the receiver.
76
9
3
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call the telephone
number on the front cover of this manual and order
part number 146148, or see your local electronics
store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current, reducing the risk of elec-
10
CONSOLE DIAGRAM
Key
Clip
FEATURES OF THE CONSOLE
The revolutionary treadmill console offers a selection
of features designed to make your workouts more
effective and enjoyable.
ETPF79506
PFTL79506
When you select the manual mode of the console,
you
can change the speed and incline of the treadmill with
the touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the handgrip pulse sensor or the optional chest pulse sensor (see page 18 for
information about the optional chest pulse sensor).
exercise ball (not included). To purchase dumbbells
or an exercise ball, call the telephone number on
the front cover of this manual.
In addition to the cross trainer programs, you can even
create your own custom workout programs and save
them in memory for future use.
To use the manual mode of the console, follow the
steps beginning on page 12. To use a cross trainer
program, see page 14. To create and use a custom
program, see pages 16 and 17.
IMPORTANT: If there is a sheet of clear plastic on
the face of the console, remove the plastic. To prevent damage to the walking platform, wear clean
athletic shoes while using the treadmill. The first
time the treadmill is used, observe the alignment of
the walking belt, and center the walking belt if necessary (see page 22).
The console also features nine interactive cross trainer
programs designed to help you to burn calories and
enhance your cardiovascular system while toning and
strengthening your muscles. These programs feature
the voice of a personal trainer to guide you through
your workouts. The cross trainer programs automatically control the speed and incline of the treadmill and
prompt you to perform a variety of strength exercises
during your workout. There are three whole body,
three upper body, and three lower body cross trainer
programs to choose among. Note: The strength exercises require the use of dumbbells and an inflatable
Note: The console can display speed and distance in
either miles or kilometers. To find which unit of measurement is selected, see THE INFORMATION MODE
on page 18. For simplicity, all instructions in this manual refer to miles.
11
HOW TO TURN ON THE POWER
3. Start the walking belt.
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room temperature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.
Plug in the power cord
(see page 10). Next, locate
the reset/off circuit breaker
on the treadmill frame near
the power cord. Switch the
circuit breaker to the reset
position.
To start the walking belt, press the Start button, the
Speed increase button, or one of the speed buttons numbered 1 to 10.
If you press the Start button or the Speed increase button, the walking belt will begin to move
at 1 mph. As you exercise, change the speed
of the walking belt as desired by pressing the
Speed increase and decrease buttons. Each time
you press a button, the speed setting will change
by 0.1 mph; if you hold down a button, the speed
setting will change in increments of 0.5 mph. Note:
After you press the buttons, it may take a moment for
the walking belt to reach the selected speed setting.
Reset
Position
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is displayed in a store. If the displays light as soon as
you plug in the power cord and switch the circuit
breaker to the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
18 to turn off the demo mode.
If you press one of the numbered speed buttons,
the walking belt will gradually change speed until it
reaches the selected speed setting.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To restart
the walking belt, press the Start button, the Speed
increase button, or one of the numbered speed buttons.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 11)
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the position of the clip.
4. Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the
Incline increase and decrease buttons or one of
the incline buttons numbered 0 to 10. Each time
you press the Incline increase or decrease button,
the incline will change by 0.5%. If you press one of
the numbered incline buttons, the treadmill will adjust to the selected incline setting. Note: After you
press the buttons, it may take a moment for the
treadmill to reach the selected incline setting.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER above.
2. Select the manual mode.
5. Follow your progress with the display.
Note: The display features several different
background colors. To select a background
color, press the Display Color button repeatedly.
When the
key is inserted, the
manual
mode will be
Track
selected. If
you have selected a program, reselect the manual mode by
pressing any of the four Programs buttons repeatedly until a track appears in the display.
12
6. Measure your heart rate if desired.
When the
manual
mode is selected, the
Track
display will
show a track
that represents 1/4 mile. As you walk or run, indicators will
appear in succession around the track until the entire track appears. The track will then disappear and
the indicators will again begin to appear in succession.
Note: If you use the handgrip pulse sensor and
the optional chest pulse sensor at the same
time, the console will not display your heart
rate accurately.
Before using
the handgrip
pulse sensor,
remove the
sheets of
clear plastic
from the metal
Contacts
contacts. In
addition,
make sure that your hands are clean.
The left side of the display will show the
elapsed time, the distance that you have
walked or run, and the incline level of the treadmill. Note: When a cross trainer program is selected, the display will show the time remaining in
the program instead of the elapsed time.
To measure your heart rate, stand on the foot
rails and hold the metal contacts on the handrail—
avoid moving your hands. When your pulse is detected, one or two dashes will appear in the right
side of the display and then your heart rate will be
shown. For the most accurate heart rate reading, continue to hold the contacts for about 15
seconds.
The right side of the display will show the approximate number of
calories you have
burned while walking or
running, the speed of
the walking belt, and your pace in minutes per
mile. The right side of the display will also show
your heart rate when you use the handgrip pulse
sensor or the optional chest pulse sensor. (See
page 18 for more information on the optional chest
pulse sensor).
7. Turn on the fan if desired.
The fan has high and low speed settings. Press the
Fan button repeatedly to select a fan speed or to
turn off the fan. Note: If the fan is on when the
walking belt stops, the fan will automatically turn off
after a few minutes.
8. When you are finished exercising, remove the
key from the console.
To reset the display, press the Stop button, remove
the key, and then reinsert the key.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
or you may damage the treadmill when you fold
it to the storage position. Next, remove the key
from the console and put it in a secure place.
To see the total number
of miles that the walking
belt has moved since the
last reset, press the
odometer (ODOM.) button; the total number of
miles will appear in the matrix for a few seconds. To
reset this number, hold down the odometer button
for a few seconds.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmill’s electrical components may wear prematurely.
13
HOW TO USE A CROSS TRAINER PROGRAM
The same speed setting and/or incline setting may
be programmed for two or more consecutive segments. During other segments, the console will
prompt you to perform strength exercises.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
Durring the
workout, the
profile will
show your
progress. The
Current Segment
flashing segment of the
profile represents the current segment of the workout. The height of the flashing segment indicates
the speed setting for the current segment. At the
end of each segment, a series of tones will sound
and the next segment of the profile will begin to
flash. If a different speed or incline setting is programmed for the next segment, the speed or incline
setting will flash in the display to alert you.
2. Select one of the nine cross trainer programs.
To select a
cross trainer
program,
press the
Upper Body
Programs
button, the
Lower Body
Programs
button, or the Whole Body Programs button repeatedly until the desired program appears in the display. When a cross trainer program is selected, the
program time will appear in the display, the maximum incline setting of the program and the maximum speed setting of the program will flash in the
display for a few seconds, and a profile of the
speed settings of the program will scroll across the
matrix in the display.
The workout will continue in this way until the last
segment of the profile flashes in the display and
the last segment ends. The walking belt will then
slow to a stop.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the speed or incline
buttons. Note: When the next segment of the
workout begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
Note: During the program, a personal trainer will
guide you through the workout. You can adjust the
volume or select an audio setting for your personal
trainer (see THE INFORMATION MODE on page
18).
3. Press the Start button to start the program.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start button or the Speed increase button. The walking belt
will begin to move at 1 mph. When the next segment of the workout begins, the treadmill will automatically adjust to the speed and incline settings for
the next segment.
A moment after you press the button, the treadmill
will automatically adjust to the first speed and incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into 25, 30, or 45 oneminute segments. One speed setting and one incline setting are programmed for most segments.
14
5. Continue the cross trainer program.
4. Perform the first strength exercise when
prompted.
When you have performed the recommended number of repetitions, the words PRESS START will
appear in the display. To continue the cross trainer
program, step onto the treadmill, slide the clip
back onto the waistband of your clothes, and
press the Start button. The treadmill will automatically adjust to the speed and incline settings for the
next segment.
When the
first strength
exercise
segment begins (only
one indicator
will flash in
the Current Segment column), the walking belt will
slow to a stop and the name of the first strength
exercise will appear in the display for a few seconds.
The program will continue in this way until the last
segment ends. The walking belt will then slow to a
stop.
Next, the personal trainer will tell you the recommended number of repetitions for the first strength
exercise.
6. Follow your progress with the display.
Remove the clip from the waistband of your
clothes, step off the treadmill, and prepare to begin
the first strength exercise. The personal trainer and
the display will count the repetitions; perform one
repetition of the exercise on each count. Exercise
with a slow, steady motion; do not perform more
than one repetition for each count.
7. Measure your heart rate if desired.
Note: Refer to the accompanying exercise chart to
see the correct form for each exercise. When performing lunges, alternate legs with each repetition.
When performing dumbbell rows, perform half the
repetitions with your right arm and half the repetitions with your left arm. The strength exercises require the use of dumbbells and an inflatable exercise ball (not included). To purchase dumbbells
or an exercise ball, call the telephone number
on the front cover of this manual.
9. When you are finished exercising, remove the
key from the console.
See step 5 on pages 12 and 13.
See step 6 on page 13.
8. Turn on the fan if desired.
See step 7 on page 13.
See step 8 on page 13.
15
HOW TO CREATE A CUSTOM PROGRAM
into one-minute segments. One speed setting and
one incline setting can be programmed for each
segment. The speed setting for the first segment
will be shown in the flashing Current Segment column of the matrix. (The incline settings are not
shown in the matrix.) To program a speed setting
and an incline setting for the first segment, simply
adjust the speed and incline of the treadmill as desired by pressing the Speed and Incline buttons.
Every few times a Speed button is pressed, an additional indicator will appear or disappear in the
Current Segment column.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
2. Select one of the custom programs.
To select a
custom program, press
the Custom
Programs
button once
or twice, until
“P10” or
“P11” appears in the display.
When the first segment of the program ends, the
current speed setting and the current incline setting
will be saved in memory. The three columns of indicators will then move one column to the left, and
the speed setting for the second segment will be
shown in the flashing Current Segment column.
Program a speed setting and an incline setting for
the second segment as described above.
Note: If the custom program has not yet been
defined, only three columns of indicators will
scroll across the matrix. If more than three
columns of indicators appear, see HOW TO
USE A CUSTOM PROGRAM on page 17.
Continue programming speed and incline settings
for as many segments as desired; custom programs can have up to forty segments. When you
are finished with your workout, press the Stop button twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
3. Press the Start button and program the desired
speed and incline settings.
A moment after you press the button, the walking
belt will begin to move. Hold the handrails and
begin walking.
See the matrix in the
display.
Each custom program
is divided
4. When you are finished exercising, remove the
key from the console.
See step 8 on page 13.
Current Segment
16
HOW TO USE A CUSTOM PROGRAM
The workout will continue in this way until the last
segment of the profile flashes in the display and
the last segment ends. The walking belt will then
slow to a stop.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
If desired, you can redefine the program while
using it. To change the speed or incline setting
for the current segment, simply press the Speed
or Incline buttons. When the current segment ends,
the new setting will be saved in memory. To increase
the length of the program, first wait until the program is completed. Then, press the Start button and
program speed and incline settings for as many additional segments as desired. When you have added
as many segments as desired, press the Stop button twice. To decrease the length of the program,
press the Stop button twice at any time before the
program is completed.
2. Select one of the custom programs.
To select a custom program, press the Custom
Programs button once or twice, until “P10” or “P11”
appears in the display.
When a custom program is selected, the maximum
speed setting of the program and the maximum incline setting of the program will flash in the display
for a few seconds. The display will also show how
long the program will last. A profile of the speed
settings of the program will scroll across the matrix.
Note: If only three columns of indicators scroll
across the matrix, see HOW TO CREATE A
CUSTOM PROGRAM on page 16.
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or the
Speed increase button. The walking belt will begin
to move at 1 mph. When the next segment of the
program begins, the treadmill will automatically adjust to the speed and incline settings for the next
segment.
3. Press the Start button to start the program.
A moment after you press the button, the treadmill
will automatically adjust to the first speed and incline settings that you programmed previously.
Hold the handrails and begin walking.
4. Follow your progress with the displays.
Each custom program is divided into several oneminute segments. One speed setting and one incline setting are programmed for each segment.
See step 5 on pages 12 and 13.
5. Measure your heart rate if desired.
See step 6 on page 13.
Durring the
workout, the
profile will
show your
progress.
Current Segment
The flashing
segment of
the profile represents the current segment of the
workout. The height of the flashing segment indicates the speed setting for the current segment. At
the end of each segment, a series of tones will
sound and the next segment of the profile will begin
to flash. If a different speed or incline setting is programmed for the next segment, the speed or incline
setting will flash in the display to alert you.
6. Turn on the fan if desired.
See step 7 on page 13.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 13.
17
THE INFORMATION MODE
Note: The console features
a display demo mode, designed to be used if the
treadmill is displayed in a
store. While the demo mode
is turned on, the console will
function normally when you plug in the power cord,
switch the reset/off circuit breaker to the reset position,
and insert the key into the console. However, when
you remove the key, the displays will remain lit, although the buttons will not function. If the demo mode
is turned on, a “d” will appear in the display while the information mode is selected. To turn on or turn off the
demo mode, press the Speed decrease button.
The console features an information mode that keeps
track of treadmill usage information. The information
mode also allows you to select miles or kilometers as
the unit of measurement, to select an audio trainer setting, and to turn on and turn off the demo mode.
To select the information mode, hold down the Stop
button, insert the key into the console, and then release
the Stop button. When the information mode is selected, the following information will appear in the display:
The center of
the display will
show the total
number of hours
that the treadmill
has been operated. The lower
part of the display will show
the total number of miles or kilometers that the walking
belt has moved. In addition, an “E” for English miles or
an “M” for metric kilometers will appear in the lower part
of the display. To change the unit of measurement,
press the Speed increase button.
To exit the information mode, remove the key from the
console.
THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor offers hands-free operation as it tracks your heart rate during your workouts.
To purchase the optional chest pulse sensor, call
the telephone number on the front cover of this
manual.
The upper left part of the display will show the personal
trainer audio setting. If you
select “ON” as the audio setting, the personal trainer will
guide you through your workouts and give detailed instructions. If you select the “OFF” setting, your personal trainer will simply guide you through your workouts. Press the Incline decrease button to change the
audio setting if desired.
You can adjust the volume
of the personal trainer
audio (0 through 5) by
pressing the Incline increase button repeatedly.
The volume setting appears as the upper right digit in the display.
18
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 lbs. (20 kg) to
raise, lower, or move the treadmill.
Frame
1. Hold the metal frame firmly in the location shown by the
arrow at the right. CAUTION: To decrease the possibility
of injury, do not lift the frame by the plastic foot rails.
Make sure to bend your legs and keep your back straight.
As you raise the frame, make sure to lift with your legs
rather than with your back.
2. Raise the frame until the latch knob locks into the storage position. Make sure that the latch knob is locked in the storage position.
Frame
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in
temperatures above 85° F (30° C).
Latch Knob
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the latch knob is
locked in the storage position.
1. Hold the handrails and place one foot against one of the
wheels.
Handrail
2. Tilt the treadmill backward until it rolls freely on the front
wheels. Carefully move the treadmill to the desired location.
To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not move the treadmill over an
uneven surface.
Wheel
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position.
19
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand. Pull
the latch knob to the left and hold it. It may be necessary to
push the frame forward as you pull the knob to the left. Pivot
the frame downward and release the latch knob.
Frame
Latch Knob
2. Hold the metal frame firmly with both hands, and lower it to
the floor. CAUTION: To decrease the possibility of injury, do
not lower the frame by gripping only the plastic foot rails.
Do not drop the frame to the floor. Make sure to bend your
legs and keep your back straight.
Frame
20
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If you need further assistance, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppressor that meets all of the specifications described on page 10. Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes, and then press the switch back in.
c
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The display of the console does not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Next, carefully lower the Uprights
(84). Remove the two indicated 3/4" Tek Screws (22).
Note: A Phillips screwdriver with a shaft at least 8 in.
(20 cm) long is required.
a
22
84
Raise the Uprights (84) to the vertical position.
Remove the three Screws (3) from the Hood (41), and
carefully pivot the Hood off.
84
41
21
3
Locate the Reed Switch (63) and the Magnet (46) on
the left side of the Front Roller (47). Turn the Front
Roller until the Magnet is aligned with the Reed
Switch. Make sure that the gap between the Magnet
and the Reed Switch is about 1/8 in. (3 mm). If necessary, move the Reed Switch slightly using a slotted
screwdriver. Reattach the Hood (not shown), making
sure that the Screws (not shown) are inserted into the
same holes from which they were removed. Then, run
the treadmill for a few minutes to check for a correct
speed reading.
Top
View
63
47
46
1/8 in.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all the specifications described on page 10.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to 8
cm) above the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is properly tightened.
b
2–3 in.
Rear Roller Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the hex key to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the left
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
22
a
b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD.
Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly
tightened, you should be able to lift each edge of the
walking belt 2 to 3 in. (5 to 8 cm) above the walking
platform. Be careful to keep the walking belt centered.
Then, plug in the power cord, insert the key, and
carefully walk on the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
b
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 18 to turn off the demo mode.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, reinsert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
23
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING: Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over the age of 35 or persons with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is intended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
24
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back foot
flat on the floor. Bend your front leg, lean forward and move your
hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times
for each leg. To cause further stretching of the achilles tendons,
bend your back leg as well. Stretches: Calves, achilles tendons and
ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks
as possible. Hold for 15 counts, then relax. Repeat 3 times for each
leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
25
5
PART LIST—Model No. PFTL72707.0
R0907A
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key
No.
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
2
5
24
1
8
2
6
4
2
2
4
2
1
1
2
1
1
2
2
1
2
16
2
2
1
1
1
2
1
2
2
3
8
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
Description
Key
No.
Qty.
Pro Shox Plus Decal
3/4" Screw
Screw
Reset/Off Circuit Breaker
Foot Rail Screw
Center Isolator
1/2" Screw
Star Washer
Platform Bolt, Back
Platform Bolt, Front
Belt Guide Screw
Belt Guide
Power Cord Grommet
Incline Motor Wire
Frame Pivot Bolt
Left Foot Rail
Right Foot Rail
Isolator Bracket Cover
Isolator Bolt
Handrail
Rear Roller Flat Washer
3/4" Tek Screw
Rear Roller Lock Washer
Motor Bolt
Transformer
Motor Belt
Drive Motor
Frame Spacer
Latch Assembly
Latch Shock Nut
Lift Frame Bolt
Lock Nut
Ground Screw
Console
Fan Screw
Power Cord
Console Fan
Controller
Latch Shock Bolt, Lower
Filter Wire
Hood
Front Roller Bushing
Lift Frame
Front Endcap
Front Roller Bolt
Magnet
Front Roller
Walking Belt
Walking Platform
Latch Shock Bolt, Upper
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
1
2
1
1
1
1
1
1
4
1
2
1
4
4
4
4
2
1
2
9
1
3
1
1
1
1
2
1
2
2
4
2
1
1
1
2
1
2
2
1
1
1
1
1
1
1
2
1
2
26
Description
Rear Roller
Left Rear Endcap
Rear Roller Bolt
Right Rear Endcap
Hex Key
Idler Arm Pulley Washer
Base Ground Wire
Frame
Belly Pan
U-nut
Reed Switch Clip
Handrail Endcap
Reed Switch
Handrail Bolt
Base Leg Bolt
Hood Cover Washer
Extension Leg Nut
Caution Decal
Latch Decal
Platform Nut
Cable Tie
Bottom Clevis Pin
Hood Clip
Tie Clamp
Releasable Tie
Access Door
Wire Harness
Extension Leg Endcap
Key/Clip
Front Wheel
Wheel Pin
Base Pad
Lift Frame Pivot Nut
Upright
Console Base
Top Clevis Pin
Hair Pin Cotter Pin
Incline Motor
Extension Leg
Rear Roller Bracket
Static Decal
Idler Arm Pivot Bolt
Hood Cover
Book Rack
Idler Arm Pivot Washer
Latch Endcap
Latch Knob
Dumbbell
Idler Arm Spacer
Wire Tie
101
102
103
104
105
106
107
108
1
4
1
1
1
1
1
2
Roller Ground Wire
Isolator
Idler Arm Spring
Pulley Bolt
Idler Arm
Idler Arm Pulley
Idler Arm Pulley Nut
Thin Base Pad
109
1
15 1/2" Wire Tie
*
–
8" Green Wire, F/R
–
4" Red Wire, M/F
*
*
–
12" Blue Wire, 2F
–
8" Blue Wire, M/F
*
*
–
User’s Manual
*These parts are not illustrated.
Specifications are subject to change without notice.
27
5
16
28
55
53
52
7
69
90
23
21
5
9
102
70
22
3
5
1
53
51
54
7
49
19
23
21
18
5
9
22
90
48
6
30
5
70
17
11
12
58
5
50
10
102
3
97
15
102
3
1
5
29
47
46
12
10
11
5
6
19
30
18
3
96
102
101
39
15
EXPLODED DRAWING A—Model No. PFTL72707.0
R0907A
EXPLODED DRAWING B—Model No. PFTL72707.0
73
R0907A
3
41
93
73
3
3
73
66
3
7
7
66
7
66
7
2
3
73
22
38
22
73
73
22
26
59
22
27
4
22
22
32
40
99
36
103
104
95
105
24
13
92
106
33
33
56 107
43
28
25
32
61 42
45
63
32
29
28
EXPLODED DRAWING C—Model No. PFTL72707.0
R0907A
8
3
64
8
3
20
3
8
64
60
62
3
3
8
3
3
3
77
3
84
62
60
44
3
83
33
31
68
65
57
82
31
22
83
77
82
78
22
87
67
89
81
33
65
68
86
82
108
22
89
22
80
44
88
82
87
22
14
72
67
81
80
108
78
22
30
3
EXPLODED DRAWING—Model No. PFTL72707.0
R0807A
EXPLODED DRAWING D—Model No. PFTL72707.0
37
94
35
35
34
79
33
85
3
3 91
2
76
3
100
3
109
71
98
75
2
74
31
R0907A
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material under normal use and service conditions. The drive motor is warranted for twelve (12) years
after the date of purchase. Parts and labor are warranted for ninety (90) days after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For inhome service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 258648 R0907A
Printed in USA © 2007 ICON IP, Inc.
Download PDF