Moxa Technologies | Industio CP-114 Series CP-114 Series | User`s manual | Moxa Technologies Industio CP-114 Series CP-114 Series User`s manual

Universal PCI Board User’s Manual
Multiport Serial Board for PCI and PCI-X Bus
First Edition, July 2007
www.moxa.com/product
MOXA Technologies Co., Ltd.
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231
Web: www.moxa.com
MOXA Technical Support
support@moxa.com
Worldwide:
support@usa.moxa.com
The Americas:
Universal PCI Board User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance
with the terms of that agreement.
Copyright Notice
Copyright © 2007 Moxa Technologies Co., Ltd.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
MOXA is a registered trademark of the Moxa Group.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part
of Moxa.
Moxa provides this document “as is,” without warranty of any kind, either expressed or implied, including, but not
limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or
to the products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no
responsibility for its use, or for any infringements on the rights of third parties that may result from its use.
This manual might include unintentional technical or typographical errors. Changes are made periodically to the
information herein to correct such errors, and these changes are incorporated into new editions of the manual.
Table of Contents
Chapter 1
Introduction ...............................................................................................1-1
Overview .............................................................................................................................. 1-2
Applications.................................................................................................................. 1-3
Package Checklist................................................................................................................. 1-4
Product Features ................................................................................................................... 1-4
Product Specifications .......................................................................................................... 1-4
Hardware ...................................................................................................................... 1-4
Interface........................................................................................................................ 1-4
Signals .......................................................................................................................... 1-5
Performance.................................................................................................................. 1-5
Configuration................................................................................................................ 1-5
Power and Environment ............................................................................................... 1-5
Certifications ................................................................................................................ 1-6
Warranty ....................................................................................................................... 1-6
Installation Guide ................................................................................................................. 1-6
Chapter 2
Hardware Installation ................................................................................2-1
Overview .............................................................................................................................. 2-2
Configuring the Board .......................................................................................................... 2-2
CP-102U ....................................................................................................................... 2-2
CP-102UL..................................................................................................................... 2-3
CP-104JU V2................................................................................................................ 2-3
CP-104UL V2............................................................................................................... 2-4
CP-114UL..................................................................................................................... 2-5
CP-118U ....................................................................................................................... 2-6
CP-118U-I .................................................................................................................... 2-7
CP-132UL V2............................................................................................................... 2-8
CP-132UL-I V2 ............................................................................................................ 2-9
CP-134U V2 ............................................................................................................... 2-10
CP-134U-I V2............................................................................................................. 2-11
CP-138U ..................................................................................................................... 2-12
CP-138U-I .................................................................................................................. 2-13
CP-168U V2 ............................................................................................................... 2-14
POS-104UL ................................................................................................................ 2-15
Plugging the Board into an Expansion Slot ........................................................................ 2-16
Chapter 3
Driver Installation: Windows Vista ..........................................................3-1
Overview .............................................................................................................................. 3-2
Installing the Driver.............................................................................................................. 3-3
Installing the Ports................................................................................................................ 3-6
Verifying the Installation .................................................................................................... 3-10
Configuring the Ports ......................................................................................................... 3-12
Disabling the Board............................................................................................................ 3-13
Uninstalling the Board........................................................................................................ 3-14
Chapter 4
Driver Installation: Windows XP/2003 .....................................................4-1
Overview .............................................................................................................................. 4-2
Installing the Driver.............................................................................................................. 4-3
Installing the Ports................................................................................................................ 4-7
Verifying the Installation .................................................................................................... 4-10
Configuring the Ports ......................................................................................................... 4-12
Using PComm .................................................................................................................... 4-13
Using Event Log................................................................................................................. 4-13
Disabling the Board............................................................................................................ 4-14
Uninstalling the Board........................................................................................................ 4-15
Chapter 5
Driver Installation: Windows 2000 ...........................................................5-1
Overview .............................................................................................................................. 5-2
Installing the Driver.............................................................................................................. 5-3
Installing the Ports................................................................................................................ 5-7
Verifying the Installation .................................................................................................... 5-10
Configuring the Ports ......................................................................................................... 5-12
Using PComm .................................................................................................................... 5-13
Using Event Log................................................................................................................. 5-13
Disabling the Board............................................................................................................ 5-14
Uninstalling the Board........................................................................................................ 5-15
Chapter 6
Driver Installation: Windows NT ..............................................................6-1
Overview .............................................................................................................................. 6-2
Installing the Driver.............................................................................................................. 6-3
Configuring the Ports ........................................................................................................... 6-7
Removing the Board............................................................................................................. 6-9
Updating the Driver............................................................................................................ 6-10
Removing the Driver ...........................................................................................................6-11
Chapter 7
Driver Installation: Windows 95/98/ME....................................................7-1
Overview .............................................................................................................................. 7-2
Installing the Driver.............................................................................................................. 7-3
Windows 95.................................................................................................................. 7-3
Windows 98 and ME .................................................................................................... 7-5
Configuring the Ports ........................................................................................................... 7-8
Updating the Driver............................................................................................................ 7-10
Removing the Driver .......................................................................................................... 7-12
Chapter 8
Driver Installation: Non Windows ............................................................8-1
Overview .............................................................................................................................. 8-2
DOS ...................................................................................................................................... 8-2
Installing the Driver...................................................................................................... 8-2
Setting up the Driver..................................................................................................... 8-3
Loading the Driver........................................................................................................ 8-5
Unloading the Driver .................................................................................................... 8-5
Linux (32-bit/64-bit)............................................................................................................. 8-6
SCO ...................................................................................................................................... 8-7
Chapter 9
Serial Programming Tools........................................................................9-1
Overview .............................................................................................................................. 9-2
Serial Programming Library................................................................................................. 9-2
PComm Utilities ................................................................................................................... 9-2
Installation .................................................................................................................... 9-2
PComm Diagnostic....................................................................................................... 9-3
PComm Monitor ........................................................................................................... 9-3
PComm Terminal Emulator.......................................................................................... 9-4
Chapter 10
Pin Assignments .....................................................................................10-1
Overview ............................................................................................................................ 10-2
CP-102U............................................................................................................................. 10-3
DB9 (male): RS-232................................................................................................... 10-3
CP-102UL .......................................................................................................................... 10-4
DB25 (female): RS-232.............................................................................................. 10-4
CP-104JU V2...................................................................................................................... 10-5
8-pin RJ45: RS-232 .................................................................................................... 10-5
CP-104UL V2..................................................................................................................... 10-6
DB44 (female): RS-232.............................................................................................. 10-6
CP-114UL........................................................................................................................... 10-7
DB44 (female): RS-232.............................................................................................. 10-7
DB44 (female): RS-422, RS-485 (4-wire).................................................................. 10-7
DB44 (female): RS-485 (2-wire)................................................................................ 10-8
CP-118U ............................................................................................................................. 10-9
DB62 (female): RS-232.............................................................................................. 10-9
DB62 (female): RS-422, RS-485 (4-wire)................................................................ 10-10
DB62 (female): RS-485 (2-wire).............................................................................. 10-11
CP-118U-I ........................................................................................................................ 10-12
DB78 (female): RS-232............................................................................................ 10-12
DB78 (female): RS-422, RS-485 (4-wire)................................................................ 10-13
DB78 (female): RS-485 (2-wire).............................................................................. 10-14
CP-132UL V2, CP-132UL-I V2 ....................................................................................... 10-15
DB25 (female): RS-422............................................................................................ 10-15
DB25 (female): RS-485 (4-wire).............................................................................. 10-15
DB25 (female): RS-485 (2-wire).............................................................................. 10-16
CP-134U V2, CP-134U-I V2............................................................................................ 10-17
DB44 (female): RS-232 (Ports 1 and 2 only) ........................................................... 10-17
DB44 (female): RS-422............................................................................................ 10-17
DB44 (female): RS-485 (4-wire).............................................................................. 10-18
DB44 (female): RS-485 (2-wire).............................................................................. 10-18
CP-138U........................................................................................................................... 10-19
DB62 (female): RS-422, RS-485 (4-wire)................................................................ 10-19
DB62 (female): RS-485 (2-wire).............................................................................. 10-20
CP-138U-I ........................................................................................................................ 10-21
DB78 (female): RS-422, RS-485 (4-wire)................................................................ 10-21
DB78 (female): RS-485 (2-wire).............................................................................. 10-22
CP-168U V2 ..................................................................................................................... 10-23
DB62 (female): RS-232............................................................................................ 10-23
POS-104UL ...................................................................................................................... 10-24
DB44 (female): RS-232............................................................................................ 10-24
Serial Connectors.............................................................................................................. 10-25
DB9 (male) ............................................................................................................... 10-25
DB25 (male) ............................................................................................................. 10-26
DB25 (female) .......................................................................................................... 10-27
RJ45.......................................................................................................................... 10-28
1
Chapter 1
The following topics are covered in this chapter:
‰
Overview
¾
‰
‰
‰
Package Checklist
Product Features
Product Specifications
¾
¾
¾
¾
¾
¾
¾
¾
‰
Applications
Hardware
Interface
Signals
Performance
Configuration
Power and Environment
Certifications
Warranty
Installation Guide
Introduction
Universal PCI Board User’s Manual
Introduction
Overview
MOXA Universal PCI (UPCI) multiport serial boards can be installed in PCI or PCI-X slots, and
support both 3.3V and 5V PCI/PCI-X. With a UPCI board, you can connect data acquisition
equipment and other serial devices to your PC over RS-232, RS-422, or RS-485. Each board has
on-chip hardware and software flow control, a built-in 128-byte Tx/Rx FIFO, and well-designed
device drivers that have been fine-tuned. This allows Moxa UPCI boards to support data
transmission speeds of up to 921.6 Kbps.
The following UPCI multiport serial boards are available from Moxa:
CP-118U-I:
CP-118U:
CP-138U-I:
CP-138U:
CP-168U V2:
CP-104UL V2:
CP-104JU V2:
POS-104UL:
CP-102UL:
CP-102U:
CP-114UL:
CP-134U V2:
CP-134U-I V2:
CP-132UL V2:
CP-132UL-I V2:
8 ports, RS-232/422/485, 2KV optical isolation
8 ports, RS-232/422/485
8 ports, RS-422/485, 2KV optical isolation
8 ports, RS-422/485
8 ports, RS-232
4 ports, RS-232, low profile
4 ports, RS-232, 8-pin RJ45 connector on-board
4 ports, RS-232, low profile, serial port powered
2 ports, RS-232, low profile
2 ports, RS-232
4 ports, RS-232/422/485, low profile
4 ports, RS-422/485
4 ports, RS-422/485, 2KV optical isolation
2 ports, RS-422/485, low profile
2 ports, RS-422/485, low profile, 2KV optical isolation
Smartio—The Smart Multiport Async Solution
The Smartio Series of multiport serial boards includes the CP-168U V2, CP-104UL V2, CP-104JU
V2, POS-104UL V2, CP-102UL, and CP-102U. These boards provide RS-232 serial ports for
connecting terminals, modems, printers, scanners, cash registers, bar code readers, keypads,
numeric displays, electrical scales, data acquisition equipment, and many other serial devices to a
PC. These boards are a reliable, high-performance solution for multiport serial communication.
Industio—The Industrial Multiport Async Solution
The Industio Series of multiport serial boards includes the CP-118U-I, CP-118U, CP-138U-I,
CP-138U, CP-114UL, CP134U V2, CP-134U-I V2, CP-132UL V2, and CP-132UL-I V2. These
boards are designed for industrial use, with serial ports that can be configured independently for
RS-232, RS-422, or RS-485 operation. Industio boards provide a reliable communication link over
distances of up to 4000 ft and support point-to-point full-duplex or multi-drop half-duplex. With
RS-485 operation, a single port can connect to 32 devices in a multi-drop environment.
ADDC™ (Automatic Data Direction Control) for RS-485
ADDC™ (Automatic Data Direction Control) makes it easier to manage 2-wire RS-485 half-duplex
connections, eliminating the need for software interference. This means that it is not necessary to
write extra code for Windows applications to control the half-duplex protocol. ADDC intelligence is
built into Industio boards.
Built-in Termination Resistors for RS-422 and RS-485
Industio boards have termination resistors built-in, eliminating the headaches involved in
determining the proper impedance for the resistors. For additional information, please refer to
Chapter 2.
1-2
Universal PCI Board User’s Manual
Introduction
ESD and Isolation Protection
Certain models include TVSS (Transient Voltage Surge Suppressor) technology to help prevent
damage due to lightning or high potential voltage. Optical isolation (2000V) and embedded surge
protection (max. ESD of 16 KV, max. EFT of 2 KV) are also available with certain models. These
features help provide protection in critical or harsh factory-type environments.
PCI Solution
UPCI boards comply with PCI Spec. 2.1 and do not require switches or jumpers. IRQ and I/O
address is automatically assigned by the PCI BIOS. This means that the board must be physically
installed in the computer first before the driver software is installed.
Universal PCI
For maximum compatibility with the PCI local bus specification, UPCI boards support both 3.3V
and 5V PCI connector types. The 32/64-bit PCI local bus specification specifies both a 3.3V/5V and
32/64-bit slot.
Operating System Support
MOXA UPCI boards are compatible with most major industrial platforms, including Windows,
DOS, and Linux. Drivers are provided for smoother installation, configuration, and performance.
This manual provides separate sections for the different operating systems that are supported.
MOXA Serial Communication Tools
For application development, MOXA provides a serial communication library for Windows called
PComm. This library can help you develop your own applications in Visual Basic, Visual C++,
Borland Delphi, and more. Utilities are included for debugging, monitoring communication status,
terminal emulation, and file transfer.
Applications
UPCI boards are suitable for many industrial applications, including the following:
z
Multipoint data acquisition
z
Factory automation
z
Critical industrial control
z
Remote serial device control
z
Internet/intranet connections
z
Remote access applications
z
Multi-user applications
z
Industrial automation
z
Office automation
z
Telecommunications
z
PC-based vending machines or kiosk systems
z
POS (Point-of-Sale) systems
1-3
Universal PCI Board User’s Manual
Introduction
Package Checklist
UPCI boards are shipped with the following items:
z
1 Moxa UPCI multiport serial board
z
Document & Software CD
z
Quick Installation Guide
z
5-year Product Warranty statement
For the CP-102UL, CP-104UL V2, POS-104UL, CP-114UL, CP-132UL V2, and CP-132UL-I V2,
the following item is also included:
z
Low profile bracket
NOTE: Notify your sales representative if any of the above items is missing or damaged. For
information on optional accessories for each model, please refer to Chapter 5.
Product Features
MOXA UPCI boards enjoy the following features:
z
Over 700 Kbps data throughput for top performance
z
Serial communication speed up to 921.6 Kbps
z
128-byte FIFO and on-chip hardware and software flow control
z
Universal PCI supporting 3.3V PCI, 5V PCI and PCI-X
z
Driver support for Windows 2000, XP, 2003, and Vista (x86 and x64)
z
On-board 15 KV ESD protection
z
Low profile for compact-sized PCs (on “L” models only)
z
2 KV optical isolation protection (on “I” models only)
Product Specifications
Hardware
I/O Controller:
Connector Type:
MU860 (compatible with 16C550C)
CP-118U-I:
Female DB78
CP-118U:
Female DB62
CP-138U-I:
Female DB78
CP-138U:
Female DB62
CP-168U V2:
Female DB62
CP-104UL V2:
Female DB44
CP-104JU V2:
8-pin RJ45
POS-104UL:
Female DB44
CP-102UL:
Female DB25
CP-102U:
Male DB9
CP-114UL:
Female DB44
CP-134U V2:
Female DB44
CP-134U-I V2:
Female DB44
CP-132UL V2:
Female DB25
CP-132UL-I V2: Female DB25
Bus:
32-bit Universal PCI
Interface
1-4
Universal PCI Board User’s Manual
Introduction
Max. No. of Boards:
CP-118U-I:
CP-118U:
CP-138U-I:
CP-138U:
CP-168U V2:
CP-104UL V2:
CP-104JU V2:
POS-104UL:
CP-102UL:
CP-102U:
CP-114UL:
CP-134U V2:
CP-134U-I V2:
CP-132UL V2:
CP-132UL-I V2:
4
RS-232:
RS-422:
4-wire RS-485:
2-wire RS-485:
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
TxD+(B), TxD-(A), RxD+(B), RxD-(A), GND
TxD+(B), TxD-(A), RxD+(B), RxD-(A), GND
Data+(B), Data-(A), GND
No. of Ports:
8
8
8
8
8
4
4
4
2
2
4
4
4
2
2
Signals
Performance
Baudrate:
50 bps to 921.6 Kbps
Configuration
Parity:
Data Bits:
Stop Bits:
I/O Address, IRQ:
FIFO:
Flow Control:
Driver Support:
Power Output:
None, Even, Odd, Space, Mark
5, 6, 7, 8
1, 1.5, 2
Assigned by BIOS
128 bytes
RTS/CTS, XON/XOFF
Windows 2000
Windows XP/2003/Vista (x86 & x64)
Linux 2.4
Linux 2.6 (x86 & x64)
Complete driver support information is available at www.moxa.com in
the Download center.
5V/12V (POS-104UL only)
Power and Environment
Operating Temperature:
Operating Humidity:
Storage Temperature:
Protection:
0 to 55°C (32 to 131°F)
5 to 95% RH
-20 to 85°C (-4 to 185°F)
Embedded 15 KV ESD protection
1-5
Universal PCI Board User’s Manual
Introduction
Certifications
Approved:
EN55022 Class B
EN55024
EN6100-3-2
EN61000-3-3
FCC Part 15 Class B
Warranty
Period:
5 years
Installation Guide
UPCI board installation can be divided into six steps as follows:
Step 1: Select serial transmission mode
For certain models, you will need to set onboard DIP switches to select the serial transmission mode
for each port. This applies to the CP-118U-I, CP-138U-I, CP-118U, CP-138U, CP-114UL, CP-134U
V2, CP-134U-I V2, CP-132UL V2, CP-132UL-I V2, and POS-104UL. For details, please refer to
Chapter 2.
Step 2: Install board
UPCI boards are installed in an open PCI or PCI-X expansion slot on the PC. For details, please refer
to Chapter 2.
Step 3: Install drivers and configure board
For details, please refer to Chapters 3 through 8.
Step 4: Connect your serial devices to the board’s serial ports
For details, please refer to Chapter 10.
Step 5: Restart system and verify driver initialization
For details, please refer to Chapters 3 through 8.
Step 6: Develop and run your serial communication application
For details, please refer to Chapter 9.
1-6
2
Chapter 2
Hardware Installation
The following topics are covered in this chapter:
‰
‰
Overview
Configuring the Board
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
‰
CP-102U
CP-102UL
CP-104JU V2
CP-104UL V2
CP-114UL
CP-118U
CP-118U-I
CP-132UL V2
CP-132UL-I V2
CP-134U V2
CP-134U-I V2
CP-138U
CP-138U-I
CP-168U V2
POS-104UL
Plugging the Board into an Expansion Slot
Universal PCI Board User’s Manual
Hardware Installation
Overview
This chapter explains the hardware installation procedure in detail. Since the BIOS automatically
assigns the IRQ number and I/O addresses, you will need to install the board before you install the
drivers. You can install up to 4 UPCI boards in one system, as long as sufficient I/O address and IRQ
number resources are available.
Configuring the Board
CP-102U
COM1
COM2
This board does not require configuration.
2-2
Universal PCI Board User’s Manual
Hardware Installation
CP-102UL
This board does not require configuration.
CP-104JU V2
This board does not require configuration.
2-3
Universal PCI Board User’s Manual
Hardware Installation
CP-104UL V2
This board does not require configuration.
2-4
Universal PCI Board User’s Manual
Hardware Installation
CP-114UL
Onboard termination resistors can be activated individually for each serial port using jumpers JP1
through JP4. JP1 corresponds to serial port 1. Short the jumper pins to activate the termination
resistor; leave the jumper pins open to bypass the termination resistor.
The onboard DIP switches, S1, S2, and S3, are used to select RS-232, RS-422, or RS-485 mode for
each serial port. Switches 1 through 4 on each bank correspond to the 4 serial ports. S3 selects
between RS-232 and RS-422/485, S2 selects between RS-422 and RS-485, and S1 selects between
2-wire and 4-wire RS-485, as follows:
Mode
S1
RS-232
--RS-422
--4-wire RS-485 ON
2-wire RS-485 OFF
S2
--ON
OFF
OFF
S3
ON
OFF
OFF
OFF
2-5
Universal PCI Board User’s Manual
Hardware Installation
CP-118U
Onboard termination resistors can be activated individually for each serial port using jumpers JP1
through JP8. JP1 corresponds to serial port 1. Short the jumper pins to activate the termination
resistor; leave the jumper pins open to bypass the termination resistor.
The onboard DIP switches, S1, S2, and S3, are used to select RS-232, RS-422, or RS-485 mode for
each serial port. There are 8 switches on each bank corresponding to the 8 serial ports. S3 selects
between RS-232 and RS-422/485, S2 selects between RS-422 and RS-485, and S1 selects between
2-wire and 4-wire RS-485, as follows:
Mode
S1
RS-232
--RS-422
--4-wire RS-485 ON
2-wire RS-485 OFF
S2
--ON
OFF
OFF
S3
ON
OFF
OFF
OFF
2-6
Universal PCI Board User’s Manual
Hardware Installation
CP-118U-I
Onboard termination resistors can be activated individually for each serial port using jumpers JP1
through JP8. JP1 corresponds to serial port 1. Short the jumper pins to activate the termination
resistor; leave the jumper pins open to bypass the termination resistor.
The onboard DIP switches, S1, S2, and S3, are used to select RS-232, RS-422, or RS-485 mode for
each serial port. There are 8 switches on each bank corresponding to the 8 serial ports. S3 selects
between RS-232 and RS-422/485, S2 selects between RS-422 and RS-485, and S1 selects between
2-wire and 4-wire RS-485, as follows:
Mode
S1
RS-232
--RS-422
--4-wire RS-485 ON
2-wire RS-485 OFF
S2
--ON
OFF
OFF
S3
ON
OFF
OFF
OFF
2-7
Universal PCI Board User’s Manual
Hardware Installation
CP-132UL V2
Onboard termination resistors can be activated individually for each serial port using jumpers JP1
and JP2. JP1 corresponds to serial port 1. Short the jumper pins to activate the termination resistor;
leave the jumper pins open to bypass the termination resistor.
The onboard DIP switches, S1 and S2, are used to select RS-422 or RS-485 mode for each serial port.
On each bank, switch 1 corresponds to port 1 and switch 2 corresponds to port 2. S2 selects between
RS-422 and RS-485; S1 selects between 2-wire and 4-wire RS-485.
2-8
Universal PCI Board User’s Manual
Hardware Installation
CP-132UL-I V2
Onboard termination resistors can be activated individually for each serial port using jumpers JP1
and JP2. JP1 corresponds to serial port 1. Short the jumper pins to activate the termination resistor;
leave the jumper pins open to bypass the termination resistor.
The onboard DIP switches, S1 and S2, are used to select RS-422 or RS-485 mode for each serial port.
On each bank, switch 1 corresponds to port 1 and switch 2 corresponds to port 2. S2 selects between
RS-422 and RS-485; S1 selects between 2-wire and 4-wire RS-485.
2-9
Universal PCI Board User’s Manual
Hardware Installation
CP-134U V2
Onboard termination resistors can be activated individually for each serial port using jumpers JP1
through JP4. JP1 corresponds to serial port 1. Short the jumper pins to activate the termination
resistor; leave the jumper pins open to bypass the termination resistor.
The onboard DIP switches, S1 and S2, are used to select RS-422 or RS-485 mode for each serial port.
Switches 1 through 4 on each bank correspond to the 4 serial ports. S2 selects between RS-422 and
RS-485; S1 selects between 2-wire and 4-wire RS-485. In addition, ports 1 and 2 can be set
individually to RS-232 mode using the on-board 30-pin jumpers, as follows:
RS422
RS485
RS232
RS422
RS485
RS232
Port1
Port1
Port2
Port2
RS-422 or RS-485 mode:
RS-232 mode:
Use the jumper to cover the left Use the jumper to cover the right
two columns of jumper pins.
two columns of jumper pins.
2-10
Universal PCI Board User’s Manual
Hardware Installation
CP-134U-I V2
Onboard termination resistors can be activated individually for each serial port using jumpers JP1
through JP4. JP1 corresponds to serial port 1. Short the jumper pins to activate the termination
resistor; leave the jumper pins open to bypass the termination resistor.
The onboard DIP switches, S1 and S2, are used to select RS-422 or RS-485 mode for each serial port.
Switches 1 through 4 on each bank correspond to the 4 serial ports. S2 selects between RS-422 and
RS-485; S1 selects between 2-wire and 4-wire RS-485. In addition, ports 1 and 2 can be set
individually to RS-232 mode using the on-board 30-pin jumpers, as follows:
RS422
RS485
RS232
RS422
RS485
RS232
Port1
Port1
Port2
Port2
RS-422 or RS-485 mode:
RS-232 mode:
Use the jumper to cover the left Use the jumper to cover the right
two columns of jumper pins.
two columns of jumper pins.
2-11
Universal PCI Board User’s Manual
Hardware Installation
CP-138U
Onboard termination resistors can be activated individually for each serial port using jumpers JP1
through JP8. JP1 corresponds to serial port 1. Short the jumper pins to activate the termination
resistor; leave the jumper pins open to bypass the termination resistor.
The onboard DIP switches, S1 and S2, are used to select RS-422 or RS-485 mode for each serial port.
There are 8 switches on each bank corresponding to the 8 serial ports. S2 selects between RS-422
and RS-485; S1 selects between 2-wire and 4-wire RS-485, as follows:
Mode
S1
RS-422
--4-wire RS-485 ON
2-wire RS-485 OFF
S2
ON
OFF
OFF
2-12
Universal PCI Board User’s Manual
Hardware Installation
CP-138U-I
Onboard termination resistors can be activated individually for each serial port using jumpers JP1
through JP8. JP1 corresponds to serial port 1. Short the jumper pins to activate the termination
resistor; leave the jumper pins open to bypass the termination resistor.
The onboard DIP switches, S1 and S2, are used to select RS-422 or RS-485 mode for each serial port.
There are 8 switches on each bank corresponding to the 8 serial ports. S2 selects between RS-422
and RS-485; S1 selects between 2-wire and 4-wire RS-485, as follows:
Mode
S1
RS-422
--4-wire RS-485 ON
2-wire RS-485 OFF
S2
ON
OFF
OFF
2-13
Universal PCI Board User’s Manual
Hardware Installation
CP-168U V2
This board does not require configuration.
2-14
Universal PCI Board User’s Manual
Hardware Installation
POS-104UL
The onboard jumpers are used to specify the pin 9 power signal for each serial port.
Step a
The top row of jumper pins selects the source of 12V power; the bottom row of jumper pins selects
the source of 5V power:
Bus power
External power
If 5V or 12V external power is enabled, you will need to connect the cable from the back of
POS-104UL to the PC’s power supply. Remove both jumpers to disable all power signals to all ports.
Step b
For each serial port, a set of 5 jumper pins is used select the power signal that is sent to pin 9.
5V
12V
RI signal (input)
To disable pin 9 power signals for a specific port, remove the jumper.
2-15
Universal PCI Board User’s Manual
Hardware Installation
Plugging the Board into an Expansion Slot
ATTENTION
Safety First!
To avoid damaging your system and board, make sure your PC’s power is turned off before
installing your Universal PCI Board.
Step 1:
Power off the PC.
Step 2:
Shut off the power to any peripheral devices and remove the PC’s cover.
Step 3:
Configure the UPCI board’s DIP switches and jumpers as necessary. This only applies to
certain models. For additional information, please refer to your model in this chapter.
Step 4:
Insert the board firmly into a free PCI or PCI-X slot on the PC.
Step 6:
Use a screw to secure the board in place.
Step 7:
Replace the PC’s cover.
Step 8:
Power on the PC. The BIOS will automatically set the IRQ and I/O address. Each MOXA
UPCI board uses one unique IRQ and I/O address, both of which are assigned
automatically by the PCI BIOS.
Step 9:
Install the software. For details, please refer to the appropriate chapter for your operating
system.
2-16
3
Chapter 3
Driver Installation: Windows Vista
The following topics are covered in this chapter:
‰
‰
‰
‰
‰
‰
‰
Overview
Installing the Driver
Installing the Ports
Verifying the Installation
Configuring the Ports
Disabling the Board
Uninstalling the Board
Universal PCI Board User’s Manual
Driver Installation: Windows Vista
Overview
This chapter explains how to install, configure, update, and remove the board drivers for Windows
Vista. The following models are supported:
CP-102U
CP-102UL
CP-104JU V2
CP-104UL V2
CP-114UL
CP-118U
CP-118U-I
CP-132UL V2
CP-132UL-I V2
CP-134U V2
CP-134U-I V2
CP-138U
CP-138U-I
CP-168U V2
POS-104UL
Windows Vista supports up to 256 serial ports, from COM1 to COM256. Moxa developed pure 32
and 64-bit Windows device drivers in order to fully utilize the advanced multi-process and
multi-thread features of Windows Vista. The drivers conform to the Win32 COMM API standard.
You can download the drivers from the MOXA website. For information on developing your own
serial programming applications, please refer to Chapter 9.
Before installing the software, be sure to install the hardware first. For details on installing the
hardware, please refer to Chapter 2.
The overall procedure for installing the
drivers is shown on the right. A newly
installed board will be automatically
detected by the operating system.
Install the board in an available PCI slot
on the PC
Start Windows
Driver already installed?
No
Install the driver from the Document &
Software CD
Configure the port
The board s serial ports should be
ready to work
3-2
Yes
Universal PCI Board User’s Manual
Driver Installation: Windows Vista
Installing the Driver
The following instructions show how to install the driver for the first time under Windows Vista.
You will need to plug the board in an available PCI or PCI-X slot first, before installing the driver.
ATTENTION
The following steps will not be necessary if a MOXA UPCI board was already installed on your
computer. Windows will automatically detect and install any additional board(s) at bootup. In this
case, you may proceed directly to configuring the ports.
Note that these instructions use the CP-118U as an example. The procedure for installing all models
is the same.
1.
After the board is physically installed and the PC boots up, Windows will automatically detect
the new board. The Found New Hardware Wizard window will open automatically. Select
Locate and install driver software (recommended).
3-3
Universal PCI Board User’s Manual
Driver Installation: Windows Vista
2.
Select I don’t have the disc. Show me other options.
3.
Select Browse my computer for driver software (advanced).
3-4
Universal PCI Board User’s Manual
4.
Driver Installation: Windows Vista
Click Browse and select the appropriate directory on the Document & Software CD for the
driver. Drivers for all operating systems are located under the product folder in the \Software
directory (e.g., under \CP-118U Series\Software).
For 32-bit (x86) platforms, select the \Windows Vista\x86 folder.
For 64-bit (x64) platforms, select the \Windows Vista\x64 folder.
After selecting the folder, click Next to continue.
5.
If you receive a warning message stating that the Windows can’t verify the publisher of the
software, select Install this driver software anyway.
3-5
Universal PCI Board User’s Manual
6.
Driver Installation: Windows Vista
After the drivers have been installed, click Close to exit the wizard.
Installing the Ports
After the board and drivers have been installed, an installation wizard will guide you through
installation of the newly added serial ports, starting with port 0.
1.
When prompted to insert a disc, select I don’t have the disc. Show me other options.
3-6
Universal PCI Board User’s Manual
2.
Driver Installation: Windows Vista
Select Browse my computer for driver software (advanced).
3-7
Universal PCI Board User’s Manual
Driver Installation: Windows Vista
3.
Click Browse and select the appropriate directory on the Document & Software CD for the
driver. Drivers for all operating systems are located under the product folder in the \Software
directory (e.g., under \CP-118U Series\Software). For 32-bit (x86) platforms, select the
\Windows Vista\x86 folder. For 64-bit (x64) platforms, select the \Windows Vista\x64 folder.
After selecting the folder, click Next to continue.
4.
If you receive a warning message stating that the Windows can’t verify the publisher of the
software, select Install this driver software anyway.
3-8
Universal PCI Board User’s Manual
5.
Driver Installation: Windows Vista
After the drivers have been installed, click Close to exit the wizard. The other serial ports will
automatically install in the background.
3-9
Universal PCI Board User’s Manual
Driver Installation: Windows Vista
Verifying the Installation
You can use Windows Device Manager to verify proper installation.
1.
Under My Computer, click System Properties.
2.
In the System window, click Device Manager.
3-10
Universal PCI Board User’s Manual
3.
Driver Installation: Windows Vista
In the Device Manager window, you should see the UPCI board under Multi-port serial
adapters (CP-118U in this example). You should also see MOXA communication ports under
Ports (COM & LPT).
If you see any special marks, such as a question mark or an exclamation mark, next to the
MOXA items, the installation of your module or serial ports was not successful. Examine the
Windows event log for details.
3-11
Universal PCI Board User’s Manual
Driver Installation: Windows Vista
Configuring the Ports
After the board and serial port drivers are installed, the board’s Properties window will appear. The
system will map the ports automatically. You may be prompted to take care of port configuration if
other Moxa boards have been installed.
1.
On the Ports Configuration tab, select a port to configure and click Port Setting.
Under Port Number, select a COM number to assign to the serial port. Select Auto
Enumerating COM Number to map subsequent ports in numerical order. For example, if
COM 3 is assigned to Port 1, then COM 4 will be automatically assigned to Port 2.
2.
3.
Select an Rx FIFO Trigger and Tx FIFO Size. The default Rx FIFO Trigger is 120 bytes (high
level). The default Tx FIFO Size is 128 bytes (high level). Select Set the change to all ports to
use this setting for all serial ports on the board.
Tx FIFO Rx FIFO
High
128
120
Middle 64
60
Low
1
1
Click OK to approve the settings for the selected port. Continue in the same way to configure
the other ports. When you have finished setting up the ports, click OK to close the Properties
window and apply the new port settings.
3-12
Universal PCI Board User’s Manual
Driver Installation: Windows Vista
Disabling the Board
1.
Right-click My Computer and select Properties in the context menu.
2.
In the System window, click Device Manager.
3.
In Device Manager, right-click the UPCI board under Multi-port serial adapters and select
Disable in the context menu. This will disable the board.
3-13
Universal PCI Board User’s Manual
Driver Installation: Windows Vista
Uninstalling the Board
1.
Right-click My Computer and select Properties in the context menu.
2.
In the System window, click Device Manager.
3.
Right-click the UPCI board under Multi-port serial adapters (CP-118U in this example) and
select Uninstall in the context menu.
4.
A confirmation dialog will appear. Click OK to uninstall the device.
3-14
4
Chapter 4
Driver Installation: Windows XP/2003
The following topics are covered in this chapter:
‰
‰
‰
‰
‰
‰
‰
‰
‰
Overview
Installing the Driver
Installing the Ports
Verifying the Installation
Configuring the Ports
Using PComm
Using Event Log
Disabling the Board
Uninstalling the Board
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
Overview
This chapter explains how to install, configure, update, and remove the board drivers for Windows
XP/2003. The following models are supported:
CP-102U
CP-102UL
CP-104JU V2
CP-104UL V2
CP-114UL
CP-118U
CP-118U-I
CP-132UL V2
CP-132UL-I V2
CP-134U V2
CP-134U-I V2
CP-138U
CP-138U-I
CP-168U V2
POS-104UL
Windows XP/2003 supports up to 256 serial ports, from COM1 to COM256. Moxa developed pure
32 and 64-bit Windows device drivers in order to fully utilize the advanced multi-process and
multi-thread features of Windows XP/2003. The drivers conform to the Win32 COMM API
standard.
You can download the drivers from the MOXA website. For information on developing your own
serial programming applications, please refer to Chapter 9.
Before installing the software, be sure to install the hardware first. For details on installing the
hardware, please refer to Chapter 2.
The overall procedure for installing the
drivers is shown on the right. A newly
installed board will be automatically
detected by the operating system.
Install the board in an available PCI slot
on the PC
Start Windows
Driver already installed?
No
Install the driver from the Document &
Software CD
Configure the port
The board s serial ports should be
ready to work
4-2
Yes
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
Installing the Driver
The following instructions show how to install the driver for the first time under Windows XP. The
same procedure is used for Windows 2003. You will need to plug the board in an available PCI or
PCI-X slot first, before installing the driver.
ATTENTION
The following steps will not be necessary if a MOXA UPCI board was already installed on your
computer. Windows will automatically detect and install any additional board(s) at bootup. In this
case, you may proceed directly to configuring the ports.
Note that these instructions use the CP-118U as an example. The procedure for installing all models
is the same.
1.
After the board is physically installed and the PC boots up, Windows will automatically detect
the new board. The Found New Hardware Wizard window will open automatically. When
prompted to connect to Windows Update, select. No, not this time and click Next to continue.
4-3
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
2.
Select Install from a list or specific location (Advanced) and click Next to continue.
3.
Select Search for the best driver in these locations and Include this location in the search.
Click Browse and select the appropriate directory on the Document & Software CD for the
driver.
Drivers for all operating systems are located under the product folder in the \Software directory
(e.g., under \CP-118U Series\Software). For 32-bit (x86) platforms, select the \Windows
XP_2003\x86 folder. For 64-bit (x64) platforms, select the \Windows XP_2003\x64 folder.
After selecting the folder, click Next to continue.
4-4
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
4.
If you see a warning that the software has not passed Windows Logo testing, click Continue
Anyway.
5.
Windows will install the drivers. When the installation is complete, click Finish.
4-5
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
4-6
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
Installing the Ports
After the board and drivers have been installed, an installation wizard will guide you through
installation of the newly added serial ports, starting with port 0.
1.
When prompted to connect to Windows Update, select No, not this time and click Next to
continue.
2.
Select Install from a list or specific location (Advanced) and click Next to continue.
4-7
Universal PCI Board User’s Manual
3.
Driver Installation: Windows XP/2003
Select Search for the best driver in these locations and Include this location in the search.
Click Browse and select the appropriate directory on the Document & Software CD for the
driver. Drivers for all operating systems are located under the product folder in the \Software
directory (e.g., under \CP-118U Series\Software).
For 32-bit (x86) platforms, select the \Windows XP_2003\x86 folder.
For 64-bit (x64) platforms, select the \Windows XP_2003\x64 folder.
After selecting the folder, click Next to continue.
4.
If you see a warning that the software has not passed Windows Logo testing, click Continue
Anyway.
4-8
Universal PCI Board User’s Manual
5.
Driver Installation: Windows XP/2003
After the drivers for the serial port have been installed, click Finish to close the wizard. Repeat
this process for the remaining serial ports.
4-9
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
Verifying the Installation
You can use Windows Device Manager to verify proper installation of the board.
1.
Right-click My Computer and select Properties in the context menu.
2.
In the Hardware tab, click Device Manager.
4-10
Universal PCI Board User’s Manual
3.
Driver Installation: Windows XP/2003
In the Device Manager window, you should see your UPCI board under Multi-port serial
adapters (CP-118U in this example). You should also see MOXA communication ports under
Ports (COM & LPT).
If you see any special marks, such as a question mark or an exclamation mark, next to the
MOXA items, the installation of the board was not successful. Examine the Windows event log
for details.
4-11
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
Configuring the Ports
After the board and serial port drivers are installed, the board’s Properties window will appear. The
system will map the ports automatically. You may be prompted to take care of port configuration if
other Moxa boards have been installed.
1.
On the Ports Configuration tab, select a port to configure and click Port Setting.
Under Port Number, select a COM number to assign to the serial port. Select Auto
Enumerating COM Number to map subsequent ports in numerical order. For example, if
COM 3 is assigned to Port 1, then COM 4 will be automatically assigned to Port 2.
2.
3.
Select an Rx FIFO Trigger and Tx FIFO Size. The default Rx FIFO Trigger is 120 bytes (high
level). The default Tx FIFO Size is 128 bytes (high level). Select Set the change to all ports to
use this setting for all serial ports on the board.
Tx FIFO Rx FIFO
High
128
120
Middle 64
60
Low
1
1
Click OK to approve the settings for the selected port. Continue in the same way to configure
the other ports. When you have finished setting up the ports, click OK to close the Properties
window and apply the new port settings.
4-12
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
Using PComm
PComm Diagnostic is a useful program for checking the board’s status. It provides internal and
external testing of IRQ, TxD/RxD, UART, CTS/RTS, DTR/DSR, and other items. You can use
PComm Diagnostic to verify that the module and serial ports are working properly.
You may download PComm from the Moxa website.
Using Event Log
You may refer to the Windows event log to verify operation of the board. To view the event log, open
Event Viewer, which is located under Administrative Tools in the Control Panel. Information about
the board will be located under the System category.
4-13
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
Disabling the Board
1.
Right-click My Computer and select Properties in the context menu.
2.
In the Hardware tab, click Device Manager.
3.
In Device Manager, right-click the UPCI board under Multi-port serial adapters and select
Disable in the context menu. This will disable the board.
4-14
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
Uninstalling the Board
1.
Right-click My Computer and select Properties in the context menu.
2.
In the Hardware tab, click Device Manager.
4-15
Universal PCI Board User’s Manual
Driver Installation: Windows XP/2003
3.
Right-click the UPCI board under Multi-port serial adapters (CP-118U in this example) and
select Uninstall in the context menu.
4.
A confirmation dialog will appear. Click OK to uninstall the device.
4-16
5
Chapter 5
Driver Installation: Windows 2000
The following topics are covered in this chapter:
‰
‰
‰
‰
‰
‰
‰
‰
‰
Overview
Installing the Driver
Installing the Ports
Verifying the Installation
Configuring the Ports
Using PComm
Using Event Log
Disabling the Board
Uninstalling the Board
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
Overview
This chapter explains how to install, configure, update, and remove the board drivers for Windows
2000. The following models are supported:
CP-102U
CP-102UL
CP-104JU V2
CP-104UL V2
CP-114UL
CP-118U
CP-118U-I
CP-132UL V2
CP-132UL-I V2
CP-134U V2
CP-134U-I V2
CP-138U
CP-138U-I
CP-168U V2
POS-104UL
Windows 2000 supports up to 256 serial ports, from COM1 to COM256. Moxa developed pure
32-bit Windows device drivers in order to fully utilize the advanced multi-process and multi-thread
features of Windows 2000. The drivers conform to the Win32 COMM API standard.
You can download the drivers from the MOXA website. For information on developing your own
serial programming applications, please refer to Chapter 9.
Before installing the software, be sure to install the hardware first. For details on installing the
hardware, please refer to Chapter 2.
The overall procedure for installing the
drivers is shown on the right. A newly
installed board will be automatically
detected by the operating system.
Install the board in an available PCI slot
on the PC
Start Windows
Driver already installed?
No
Install the driver from the Document &
Software CD
Configure the port
The board s serial ports should be
ready to work
5-2
Yes
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
Installing the Driver
The following instructions show how to install the driver for the first time under Windows 2000.
You will need to plug the board in an available PCI or PCI-X slot first, before installing the driver.
ATTENTION
The following steps will not be necessary if a MOXA UPCI board was already installed on your
computer. Windows will automatically detect and install any additional board(s) at bootup. In this
case, you may proceed directly to configuring the ports.
Note that these instructions use the CP-118U as an example. The procedure for installing all models
is the same.
1.
After the board is physically installed and the PC boots up, Windows will automatically detect
the new board and the Found New Hardware Wizard window will open automatically. Click
Next to continue.
5-3
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
2.
Select Search for a suitable driver for my device (recommended) and click Next to
continue.
3.
Select Specify a location and click Next to continue.
5-4
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
4.
Click Browse and select the appropriate directory on the Document & Software CD for the
driver. Drivers for all operating systems are located under the product folder in the \Software
directory (e.g., under \CP-118U Series\Software). Select the \Windows 2K folder and click
Next to continue.
5.
After the wizard has located the driver files, click Next to proceed.
5-5
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
6.
If you see a warning that the digital signature has not been found, click Yes to proceed.
7.
Windows will install the drivers. When the installation is complete, click Finish.
5-6
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
Installing the Ports
After the board and drivers have been installed, an installation wizard will guide you through
installation of the newly added serial ports, starting with port 0.
1.
When the installation wizard opens, click Next to proceed.
2.
Select Search for a suitable driver for my device (recommended) and click Next to
continue.
5-7
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
3.
Select Specify a location and click Next to continue.
4.
Click Browse and select the appropriate directory on the Document & Software CD for the
driver. Drivers for all operating systems are located under the product folder in the \Software
directory (e.g., under \CP-118U Series\Software). Select the \Windows 2K folder and click
Next to continue.
5-8
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
5.
After the wizard has located the driver files, click Next to proceed.
6.
After the drivers have been installed, click Finish to exit the wizard. The other serial ports will
automatically install in the background.
5-9
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
Verifying the Installation
You can use Windows Device Manager to verify proper installation of the board.
1.
Right-click My Computer and select Properties in the context menu.
2.
In the Hardware tab, click Device Manager.
5-10
Universal PCI Board User’s Manual
3.
Driver Installation: Windows 2000
In the Device Manager window, you should see your UPCI board under Multi-port serial
adapters (CP-118U in this example). You should also see MOXA communication ports under
Ports (COM & LPT).
If you see any special marks, such as a question mark or an exclamation mark, next to the
MOXA items, the installation of the board was not successful. Examine the Windows event log
for details.
5-11
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
Configuring the Ports
After the board and serial port drivers are installed, the board’s Properties window will appear. The
system will map the ports automatically. You may be prompted to take care of port configuration if
other Moxa boards have been installed.
1.
On the Ports Configuration tab, select a port to configure and click Port Setting.
Under Port Number, select a COM number to assign to the serial port. Select Auto
Enumerating COM Number to map subsequent ports in numerical order. For example, if
COM 3 is assigned to Port 1, then COM 4 will be automatically assigned to Port 2.
2.
3.
Select an Rx FIFO Trigger and Tx FIFO Size. The default Rx FIFO Trigger is 120 bytes (high
level). The default Tx FIFO Size is 128 bytes (high level). Select Set the change to all ports to
use this setting for all serial ports on the board.
Tx FIFO Rx FIFO
High
128
120
Middle 64
60
Low
1
1
Click OK to approve the settings for the selected port. Continue in the same way to configure
the other ports. When you have finished setting up the ports, click OK to close the Properties
window and apply the new port settings.
5-12
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
Using PComm
PComm Diagnostic is a useful program for checking the board’s status. It provides internal and
external testing of IRQ, TxD/RxD, UART, CTS/RTS, DTR/DSR, and other items. You can use
PComm Diagnostic to verify that the module and serial ports are working properly.
You may download PComm from the Moxa website.
Using Event Log
You may refer to the Windows event log to verify operation of the board. To view the event log, open
Event Viewer, which is located under Administrative Tools in the Control Panel. Information about
the board will be located under the System category.
5-13
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
Disabling the Board
1.
Right-click My Computer and select Properties in the context menu.
2.
In the Hardware tab, click Device Manager.
3.
In Device Manager, right-click the UPCI board under Multi-port serial adapters and select
Disable in the context menu. This will disable the board.
5-14
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
Uninstalling the Board
1.
Right-click My Computer and select Properties in the context menu.
2.
In the Hardware tab, click Device Manager.
5-15
Universal PCI Board User’s Manual
Driver Installation: Windows 2000
3.
Right-click the UPCI board under Multi-port serial adapters (CP-118U in this example) and
select Uninstall in the context menu.
4.
At the warning prompt, click OK to uninstall the device.
5-16
6
Chapter 6
Driver Installation: Windows NT
The following topics are covered in this chapter:
‰
‰
‰
‰
‰
‰
Overview
Installing the Driver
Configuring the Ports
Removing the Board
Updating the Driver
Removing the Driver
Universal PCI Board User’s Manual
Driver Installation: Windows NT
Overview
This chapter explains how to install, configure, update, and remove the board drivers for Windows
NT. The following models are supported:
CP-102U
CP-102UL
CP-104JU V2
CP-104UL V2
CP-118U
CP-118U-I
CP-132UL V2
CP-132UL-I V2
CP-134U V2
CP-134U-I V2
CP-168U V2
Windows NT supports up to 256 serial ports, from COM1 to COM256. Moxa developed pure 32-bit
Windows device drivers in order to fully utilize the advanced multi-process and multi-thread
features of Windows NT. The drivers conform to the Win32 COMM API standard.
You can download the drivers from the MOXA website. For information on developing your own
serial programming applications, please refer to Chapter 9.
Before installing the software, be sure to install the hardware first. For details on installing the
hardware, please refer to Chapter 2.
The overall procedure for installing the
Install the board in an available PCI slot
drivers is shown on the right. Windows
on the PC
NT will not automatically detect a newly
installed board. You will need to manually
add the board in the operating system.
Start Windows
Driver already installed?
No
Install the driver from the Document &
Software CD
Configure the port
The board s serial ports should be
ready to work
6-2
Yes
Universal PCI Board User’s Manual
Driver Installation: Windows NT
Installing the Driver
You will need to plug the board in an available PCI or PCI-X slot first, before installing the driver.
Note that these instructions use the CP-168U V2 as an example. The procedure for installing all
models is the same.
1.
Log into Windows NT as Administrator.
2.
Locate the appropriate folder for your board’s drivers on the Document & Software CD. The
NT drivers will be located under the product folder in the \Software\WinNT directory (e.g.,
under \CP-118U Series\Software). Copy this folder to the PC’s hard disk and remember its
location.
3.
In the Control Panel, open Network applet. On the Adapters tab, click Add. When prompted
to select a product, click Have Disk…
You will be prompted to enter the path to the driver. Enter the location of the drivers that you
copied from the Document & Software CD (C:\Windows.nt in this example) and then click
OK.
6-3
Universal PCI Board User’s Manual
Driver Installation: Windows NT
4.
When prompted, select your board model (Smartio/Industio Family multiport board in this
example) and click OK.
5.
After the files have been installed, a configuration panel will open. This is where boards are
installed, configured, and removed. If another board has already been installed on the system, it
will already be listed. Windows NT does not automatically detect Moxa UPCI boards, so you
will need to click Add for a newly installed board.
6-4
Universal PCI Board User’s Manual
6.
Driver Installation: Windows NT
Under Board Type, select the UPCI board that is being installed. The window will show the
COM settings for the serial ports on the board. You can modify the COM settings for any port at
this time by selecting a port and clicking Port Setting. If you are satisfied with the COM
settings, click OK to return to the configuration panel.
6-5
Universal PCI Board User’s Manual
Driver Installation: Windows NT
7.
The board will now appear in the configuration panel (CP-168U Series in this example). Click
OK to return to the Network applet. After that, click OK again to exit the Network applet
8.
Restart the PC. After you have logged back into Windows NT, you may check the event log
issued by the MOXA driver to see if the board’s ports have been initialized successfully. In the
Administrative group, open Event Viewer and select Log and System. For each newly
installed or configured Moxa UPCI board, check for a message stating that the board has been
enabled (e.g., “MOXA CP-168U V2 board, with first serial port COM3, has been enabled”).
ATTENTION
The driver configuration will NOT take effect until you restart the PC.
Double check that all CP-168U V2 board components are connected and fastened tightly to ensure
that the system and the driver can start up successfully.
6-6
Universal PCI Board User’s Manual
Driver Installation: Windows NT
Configuring the Ports
1.
In Windows Control Panel, open the Network applet. In the Adapters tab, UPCI boards will
appear as a type of Moxa adapter (MOXA Smartio/Industio Family Adapter in this example).
Select the Moxa adapter and click Properties…
2.
The configuration panel will open with a list of installed boards. Select your board and click
Property. Up to 4 Moxa UPCI boards can be installed at a time.
6-7
Universal PCI Board User’s Manual
3.
Driver Installation: Windows NT
Select a port to configure and click Port Setting.
Under Port Number, select a COM number to assign to the serial port. Select Auto
Enumerating COM Number to map subsequent ports in numerical order. For example, if
COM 3 is assigned to Port 1, then COM 4 will be automatically assigned to Port 2.
4.
Select an Rx FIFO Trigger and Tx FIFO Size. The default Rx FIFO Trigger is 120 bytes (high
level). The default Tx FIFO Size is 128 bytes (high level). Select Set the change to all ports to
use this setting for all serial ports on the board.
High
Middle
Low
Tx FIFO
128
64
1
Rx FIFO
120
60
1
6-8
Universal PCI Board User’s Manual
5.
Driver Installation: Windows NT
Click OK to approve the settings for the selected port. Continue in the same way to configure
the other ports. When you have finished setting up the ports, click OK to close the Properties
window and apply the new port settings. Click OK again to exit the Network applet.
Removing the Board
To remove a board, shut of your PC and physically remove the board from the PCI slot. The next
time you start up the PC, Windows NT will automatically remove the configuration. You do not need
to go through the Windows control panel.
6-9
Universal PCI Board User’s Manual
Driver Installation: Windows NT
Updating the Driver
1.
In Windows Control Panel, open the Network applet. In the Adapters tab, UPCI boards will
appear as a type of Moxa adapter (MOXA Smartio/Industio Family Adapter in this example).
Select the Moxa adapter and click Remove.
2.
Restart the system.
3.
Go through the process of installing the drivers using the new drivers.
6-10
Universal PCI Board User’s Manual
Driver Installation: Windows NT
Removing the Driver
1.
In Windows Control Panel, open the Network applet. In the Adapters tab, UPCI boards will
appear as a type of Moxa adapter (MOXA Smartio/Industio Family Adapter in this example).
Select the Moxa adapter and click Remove.
2.
Click OK to exit the Network applet and restart the system.
6-11
7
Chapter 7
Driver Installation: Windows 95/98/ME
The following topics are covered in this chapter:
‰
‰
Overview
Installing the Driver
¾
¾
‰
‰
‰
Windows 95
Windows 98 and ME
Configuring the Ports
Updating the Driver
Removing the Driver
Universal PCI Board User’s Manual
Driver Installation: Windows 95/98/ME
Overview
This chapter explains how to install, configure, update, and remove the board drivers for Windows
95/98/ME. The following models are supported:
CP-102U
CP-102UL
CP-104JU V2
CP-104UL V2
CP-118U
CP-118U-I
CP-132UL V2
CP-132UL-I V2
CP-134U V2
CP-134U-I V2
CP-168U V2
Windows 95/98/ME supports up to 128 serial ports, from COM1 to COM128. In order to fully
utilize the advanced multi-process and multi-thread features of Windows 95/98/ME, Moxa
developed pure 32-bit virtual device port drivers (VxD) that are compliant with communication
drivers (VCOMM). The drivers conform to the Win32 COMM API standard.
You can download the drivers from the MOXA website. For information on developing your own
serial programming applications, please refer to Chapter 9.
Before installing the software, be sure to install the hardware first. For details on installing the
hardware, please refer to Chapter 2.
The overall procedure for installing the
drivers is shown on the right. A newly
installed board will be automatically
detected by the operating system.
Install the board in an available PCI slot
on the PC
Start Windows
Driver already installed?
No
Install the driver from the Document &
Software CD
Configure the port
The board s serial ports should be
ready to work
7-2
Yes
Universal PCI Board User’s Manual
Driver Installation: Windows 95/98/ME
Installing the Driver
The following instructions show how to install the driver for the first time under Windows 95/98/ME.
You will need to plug the board in an available PCI or PCI-X slot first, before installing the driver.
ATTENTION
The following steps will not be necessary if a MOXA UPCI board was already installed on your
computer. Windows will automatically detect and install any additional board(s) at bootup. In this
case, you may proceed directly to configuring the ports.
Windows 95
1.
After the board is physically installed and the PC boots up, Windows will automatically detect
the new board and the Found New Hardware Wizard window will open. Click Next to
continue.
2.
Select Other Locations…
7-3
Universal PCI Board User’s Manual
Driver Installation: Windows 95/98/ME
3.
Click Browse and select the appropriate directory on the Document & Software CD for the
driver. Drivers for all operating systems are located under the product folder in the \Software
directory (e.g., under \CP-168U V2\Software). Select the \Win9x folder and click OK to
continue.
4.
After Windows finds the drivers, click Finish.
You may begin configuring and using the new COM ports right away without restarting
Windows.
7-4
Universal PCI Board User’s Manual
Driver Installation: Windows 95/98/ME
Windows 98 and ME
1.
After the board is physically installed and the PC boots up, Windows will automatically detect
the new board and the Found New Hardware Wizard window will open. Click Next to
continue.
2.
Select Display a list... and click Next.
7-5
Universal PCI Board User’s Manual
Driver Installation: Windows 95/98/ME
3.
Select Other Devices and click Next.
4.
Select Have Disk…
5.
Click Browse and select the appropriate directory on the Document & Software CD for the
driver. Drivers for all operating systems are located under the product folder in the \Software
directory (e.g., under \CP-168U V2 \Software). Select the \Win9x folder and click OK to
continue.
7-6
Universal PCI Board User’s Manual
6.
Driver Installation: Windows 95/98/ME
After Windows installs the drivers, click Finish.
7-7
Universal PCI Board User’s Manual
Driver Installation: Windows 95/98/ME
Configuring the Ports
You may configure the COM ports after the board and drivers have been installed.
1.
In the Windows Control Panel, open the System applet.
2.
In the Device Manager tab, expand the Moxa Smartio/Industio multiport board category by
clicking the “+” sign next to it. Select the desired board (CP-168U in this example) and click
Properties.
7-8
Universal PCI Board User’s Manual
3.
Driver Installation: Windows 95/98/ME
On the Ports Configuration tab, select a port to configure and click Port Setting.
Under Port Number, select a COM number to assign to the serial port. Select Auto
Enumerating COM Number to map subsequent ports in numerical order. For example, if
COM 3 is assigned to Port 1, then COM 4 will be automatically assigned to Port 2.
4.
5.
Select an Rx FIFO Trigger and Tx FIFO Size. The default Rx FIFO Trigger is 120 bytes (high
level). The default Tx FIFO Size is 128 bytes (high level). Select Set the change to all ports to
use this setting for all serial ports on the board.
Tx FIFO Rx FIFO
High
128
120
Middle 64
60
Low
1
1
Click OK to approve the settings for the selected port. Continue in the same way to configure
the other ports. When you have finished setting up the ports, click OK to close the Properties
window and apply the new port settings. Click OK again to close the Device Manager and
restart the system.
7-9
Universal PCI Board User’s Manual
Driver Installation: Windows 95/98/ME
Updating the Driver
You may configure the COM ports after the board and drivers have been installed.
1.
In the Windows Control Panel, open the System applet.
2.
In the Device Manager tab, expand the Moxa Smartio/Industio multiport board category by
clicking the “+” sign next to it. Select the desired board (CP-168U in this example) and click
Properties.
7-10
Universal PCI Board User’s Manual
Driver Installation: Windows 95/98/ME
3.
In the Driver tab, click Update Driver....
4.
Select the appropriate model (CP-168U in this example) and click Have Disk...
7-11
Universal PCI Board User’s Manual
Driver Installation: Windows 95/98/ME
5.
When prompted, select the appropriate directory on the Document & Software CD for the
driver. Drivers for all operating systems are located under the product folder in the \Software
directory (e.g., under \CP-118U Series\Software). Select the \Win9x folder and click OK to
continue.
6.
You will be prompted to restart the system. The new drivers will be in effect the next time you
restart.
Removing the Driver
1.
In the Windows Control Panel, open the Add/Remove Programs applet. On the
Install/Uninstall tab, select MOXA Smartio/Industio Driver and click Add/Remove.
2.
When prompted, click Yes to confirm that you want to remove the driver.
3.
After the driver has been removed, click OK to return to the Add/Remove Programs applet.
7-12
8
Driver Installation: Non Windows
Chapter 8
The following topics are covered in this chapter:
‰
‰
Overview
DOS
¾
¾
¾
¾
‰
‰
Installing the Driver
Setting up the Driver
Loading the Driver
Unloading the Driver
Linux (32-bit/64-bit)
SCO
Universal PCI Board User’s Manual
Driver Installation: Non Windows
Overview
This chapter explains how to install, configure, update, and remove the board drivers for non
Windows operating systems. Before installing the software, be sure to install the hardware first. For
details on installing the hardware, please refer to Chapter 2.
You can download DOS, Linux, and SCO drivers from the MOXA website. For information on
developing your own serial programming applications, please refer to the next chapter.
DOS
MOXA DOS API-232 is a software package that can help you develop or debug serial
communications programs. This section will show you how to install the package, how to set up the
driver, and how to load or unload the driver. The following models are supported:
CP-102U
CP-102UL
CP-104JU V2
CP-104UL V2
CP-114UL
CP-118U
CP-118U-I
CP-132UL V2
CP-132UL-I V2
CP-134U V2
CP-134U-I V2
CP-138U
CP-138U-I
CP-168U V2
POS-104UL
Installing the Driver
1.
Run the installation program, DOSINST.EXE under \Software\DOS on the Document &
Software CD. Specify the target directory for the API-232 files (e.g., C:\MOXA). Press F2 to
start the installation.
8-2
Universal PCI Board User’s Manual
2.
Driver Installation: Non Windows
After installation is complete, you will be prompted to set up the board and driver initial values.
It is strongly recommended that you set up the board and driver at this time by pressing Y.
Setting up the Driver
The following instructions are not intended to illustrate every function of the setup program. For
more detailed information, please refer to the help files by pressing F1 in the setup program.
1.
Run the setup program, BIN\SETUP.EXE.
2.
Select your board model (CP-134U in this example) and press Enter.
8-3
Universal PCI Board User’s Manual
Driver Installation: Non Windows
3.
Press PgDn to view and modify the setup options for the selected board.
4.
The settings for each port will be displayed. Verify the settings and make any necessary
changes.
Port number:
This is the port ID of each port. Application software will refer to a port
by its port number (ID). Port numbers must be unique; duplicate port
numbers are not allowed. The port number can range from 0 to 255 as
long as it does not overlap with another port. Generally, you should
consider the convenience of programming when specifying the port
number.
TxD buffer size:
This is the transmission (output) buffer allocated in the system for each
port.
8-4
Universal PCI Board User’s Manual
5.
Driver Installation: Non Windows
RxD buffer size:
This is the receiving (input) buffer allocated in the system for each port.
F5: Group Edit:
This allows you to configure several ports simultaneously as a group.
Press F10 to save the latest configuration and exit the setup program.
Loading the Driver
After setting up the driver, you must load the driver in order to gain access to the serial ports on the
serial board. Run BIN\DP-DRV.EXE at the DOS prompt. The driver will detect your multiport
serial board automatically. You should see messages indicating successful detection of your module,
such as the following:
Smartio/Industio Family DOS driver Version 1.9
Setup driver .
CP-134U series (Bus= x ,Dev=y) : OK!
Device driver setup O.K.
At this point, you can execute applications that support API-232 functions, or start developing
applications using the API-232 library.
Unloading the Driver
To unload or release the driver from memory, enter DP-DRV /Q at the DOS prompt.
8-5
Universal PCI Board User’s Manual
Driver Installation: Non Windows
Linux (32-bit/64-bit)
The Linux drivers support the following models:
CP-102U
CP-102UL
CP-104JU V2
CP-104UL V2
CP-114UL
CP-118U
CP-118U-I
CP-132UL V2
CP-132UL-I V2
CP-134U V2
CP-134U-I V2
CP-138U
CP-138U-I
CP-168U V2
POS-104UL
To install and load the Linux drivers, enter the following commands from the Linux prompt:
# mkdir moxa
# cd moxa
# tar xvfz mxser.tgz
# cd mxser
# make clean; make install
# cd /moxa/mxser/driver
# ./msmknod
# modprobe mxser
If the driver has loaded successfully, you should see a message such as the following:
MOXA Smartio/Industio family driver version 1.11
Found MOXA CP-168U series board(BusNo=2,DevNo=13)
ttyM0 – ttyM7 max. baudrate = 921600 bps
You can verify that the driver has loaded by entering the following:
# lsmode |grep mxser
You should see a message such as the following:
mxser 59484 0
The installation will include msdiag, a diagnostic utility, msterm, a terminal emulation program,
and msmon, a monitoring utility. For additional information, please refer to readme.txt in the
/home/moxa/mxser directory.
8-6
Universal PCI Board User’s Manual
Driver Installation: Non Windows
SCO
The MOXA SCO driver supports the following boards and SCO versions:
Supported Boards
CP-102U
CP-102UL
CP-104JU V2
CP-104UL V2
CP-118U
CP-138U-I
CP-168U V2
1.
Supported SCO Versions
SCO OpenServer 5/6
SCO UnixWare 7
To install the SCO drivers, first copy the driver file .tar to your host using the following
commands:
#tar xvf <driver tar file>
/tmp/moxa/mxintall
/tmp/moxa/sco.tar
# cd/tmp/mxinstall
# ./mxinstall
2.
You should see the following message. Press any key to continue.
Copyright© 2004 Moxa Technologies Co., Ltd.
All Rights Reserved.
MOXA Smartio Family Device Driver Installation (Ver 1.6)
For SCO UNIX System V/386 Release 3.2
Tar files, please wait...O.K.
Press any key to continue
3.
A configuration window should appear. Under SCO Unix/SCO Open Server, you can install up
to four Moxa UPCI boards.
MOXA Smartio Family Installation Utility (Ver 1.9)
Smartio Family Basic Configuration
Board No.
Board Type I/O Address Interrupt
Bus/Dev No.
1
None
-------------------------- ------------2
None
-------------------------- ------------3
None
-------------------------- ------------4
None
-------------------------- ------------PgDn: getty Setting
Esc: Exit
Enter: Confirm Input Value
Tab: Change Item
Select the board that you are installing and press Enter.
None
C168 ISA Series
C104 ISA Series
C168 PCI Series
C104 PCI Series
CP-104UL Series
CP-168U Series
CP-118U Series
CP-102U/UL Series
CP-104JU Series
8-7
Universal PCI Board User’s Manual
4.
Driver Installation: Non Windows
You should see a message indicating the I/O address, buss number, and device number for the
board. These resources will be automatically assigned by the SCO system. Press Enter to
return to the main configuration screen.
PCI Boards Selecting
1
I/O Addr= AC00, BusNo=2, DevNo=13
Enter: Select ESC: Exit
5.
Press Esc to save the configuration and exit. Confirm this action by pressing Y.
6.
The driver files will be copied to the SCO system. When prompted, press any key to continue.
Save configuration changes? (Y/N)
Copying driver files and configuring system. Please wait..
Press any key to continue! _
7.
When prompted press Y to rebuild the system.
8.
After the system is rebuilt, press any key to return to the shell command. You will now have
access to the serial ports on the UPCI board.
Do you want to rebuild the system? (y/n)_
Do you want to rebuild the system? (y/n)
Rebuilding kernel. Please wait..
Rebuilding kernel completed.
Please remember to manually reboot your system later.
Press any key to continue. _
8-8
9
Chapter 9
Serial Programming Tools
The following topics are covered in this chapter:
‰
‰
‰
Overview
Serial Programming Library
PComm Utilities
¾
¾
¾
¾
Installation
PComm Diagnostic
PComm Monitor
PComm Terminal Emulator
Universal PCI Board User’s Manual
Serial Programming Tools
Overview
MOXA provides Windows serial programming libraries and troubleshooting utilities that are easy to
use and powerful. You can use these tools to reduce software development time.
The serial communication library is useful for developing applications for data communications,
remote access, data acquisition, and industrial control. It provides a simpler solution compared to the
more complex Windows Win32 COMM API.
PComm is a professional serial communication tool for Windows PCs. PComm includes the
following features:
z
Useful utilities for diagnostics, port monitoring, and terminal emulation
z
Sample programs
z
Comprehensive help files
Serial Programming Library
The serial programming library assists you in developing serial communications programs for any
COM port that complies with the Microsoft Win32 API. It facilitates the implementation of
multi-process and multi-thread serial communication programs and can remarkably reduce
development time.
The library provides a complete set of functions as well as various sample programs for Visual C++,
Visual Basic, and Delphi. To view detailed descriptions of the available functions and sample
programs, go to Start Æ Program Æ PComm Lite and select PComm Lib Help, PComm
Porting Notes, or PComm Programming Guide. You may also refer to the sample programs in the
PComm directory.
PComm Utilities
This section provides brief descriptions of the PComm utilities. For more information about these
utilities, please refer to the Windows help files or to the API-232.txt file for DOS.
Installation
To install PComm, run Setup.exe from the Document and Software CD. Please note that the
PComm diagnostic and monitor utilities are for MOXA boards only. These two utilities will not
work with other serial boards.
9-2
Universal PCI Board User’s Manual
Serial Programming Tools
PComm Diagnostic
PComm Diagnostic is designed for MOXA boards only. It provides internal and external testing of
IRQ, TxD/RxD, UART, CTS/RTS, DTR/DSR, DTR/DCD, and other items. You can use PComm
Diagnostic to check the operation of both software and hardware.
To run the Diagnostic program, go to Start Æ Program Æ PComm Lite Æ Diagnostic.
PComm Monitor
PComm Monitor is designed for MOXA boards in Windows NT only. It allows you to monitor data
transmission of selected MOXA COM ports. It monitors data transmission, throughput, and line
status at regular intervals. Click on a specific port to view that port’s communication parameters and
status.
To run PComm Monitor, go to Start Æ Program Æ PComm Lite Æ Monitor.
9-3
Universal PCI Board User’s Manual
Serial Programming Tools
PComm Terminal Emulator
PComm Terminal Emulator can be used to connect to a serial port to verify that data transmission is
functioning correctly. It supports multiple windows and both VT100 and ANSI terminal types. You
can interactively transfer data, periodically send patterns, and transfer files using ASCII, XMODEM,
YMODEM, ZMODEM, and KERMIT protocols.
To run PComm Terminal Emulator, go to Start Æ Program Æ PComm Lite Æ Terminal
Emulator.
9-4
10
Chapter 10
The following topics are covered in this chapter:
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
Overview
CP-102U
CP-102UL
CP-104JU V2
CP-104UL V2
CP-114UL
CP-118U
CP-118U-I
CP-132UL V2, CP-132UL-I V2
CP-134U V2, CP-134U-I V2
CP-138U
CP-138U-I
CP-168U V2
POS-104UL
Serial Connectors
¾
¾
¾
¾
DB9 (male)
DB25 (male)
DB25 (female)
RJ45
Pin Assignments
Universal PCI Board User’s Manual
Pin Assignments
Overview
This chapter provides the pin assignments for each Moxa UPCI multiport serial board, as well as the
pin assignments for the optional accessories. Moxa UPCI boards do not have built-in serial port
connectors. The only exception is the CP-102U, which is built with two DB9 (male) serial
connectors. For all other models, you will need a cable or other accessory with standard serial
connectors in order to connect serial devices to the board. The following chart shows the available
cables and accessories for each model.
Model
CP-102U
CP-102UL
CP-132UL V2
CP-132UL-I V2
CP-104UL V2
CP-114UL
CP-134U V2
CP-134U-I V2
CP-104JU V2
CP-118U
CP-138U
CP-168U V2
Board Connector
2×DB9 (male)
Supported Accessories
---
Serial Connectors
---
DB25 (female)
CBL-M25M9x2-50
2×DB9 (male)
CBL-M44M9x4-50
4×DB9 (male)
CBL-M44M25x4-50
4×DB25 (male)
CBL-RJ45M9-150
CBL-RJ45M25-150
OPT8-M9
CBL-M62M9x8-100 (OPT8D)
OPT8B
CBL-M62M25x8-100 (OPT8C)
4×DB9 (male)
4×DB25 (male)
DB44 (female)
RJ45
DB62 (female)
8×DB9 (male)
8×DB25 (male)
OPT8A, OPT8S, OPT8F, OPT8Z,
8×DB25 (female)
OPT8K, OPT8I
OPT8-RJ45*
8×RJ45
CP-118U-I
CBL-M78M9x8-100
8×DB9 (male)
DB78 (female)
CP-138U-I
CBL-M78M25x8-100
8×DB25 (male)
POS-104UL
DB44 (female)
CBL-M44M9x4-50(POS)
4×DB9 (male)
* The OPT8-RJ45 is designed for RS-232 only. It should only be used with the CP-118U in RS-232
mode or with the CP-168U V2.
The serial connectors on each accessory use standard serial port pin assignments. Please refer to the
Serial Connectors section for details.
10-2
Universal PCI Board User’s Manual
Pin Assignments
CP-102U
1
6
5
9
This board supports RS-232 only.
Model
CP-102U
Board Connector
2×DB9 (male)
Supported Accessories
---
DB9 (male): RS-232
Pin
1
2
3
4
5
6
7
8
Signal
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
10-3
Serial Connectors
---
Universal PCI Board User’s Manual
Pin Assignments
CP-102UL
This board supports RS-232 only.
Model
CP-102UL
Board Connector
DB25 (female)
Supported Accessories
CBL-M25M9x2-50
DB25 (female): RS-232
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Signal
--DCD1
GND
CTS1
RxD1
------DTR0
DSR0
RTS0
TxD0
---
Pin
14
15
16
17
18
19
20
21
22
23
24
25
---
Signal
--DTR1
DSR1
RTS1
TxD1
----DCD0
GND
CTS0
RxD0
-----
10-4
Serial Connectors
2×DB9 (male)
Universal PCI Board User’s Manual
Pin Assignments
CP-104JU V2
1
8
This board supports RS-232 only.
Model
Board Connector
CP-104JU V2
RJ45
Supported Accessories
CBL-RJ45M9-150
CBL-RJ45M25-150
8-pin RJ45: RS-232
Pin
1
2
3
4
5
6
7
8
Signal
DSR
RTS
GND
TxD
RxD
DCD
CTS
DTR
10-5
Serial Connectors
4×DB9 (male)
4×DB25 (male)
Universal PCI Board User’s Manual
Pin Assignments
CP-104UL V2
This board supports RS-232 only.
Model
Board Connector
CP-104UL V2
DB44 (female)
Supported Accessories
CBL-M44M9x4-50
CBL-M44M25x4-50
Serial Connectors
4×DB9 (male)
4×DB25 (male)
DB44 (female): RS-232
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
TxD3
RxD3
RTS3
--TxD2
RxD2
RTS2
--TxD1
RxD1
RTS1
--TxD0
RxD0
RTS0
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal
CTS3
DTR3
DSR3
--CTS2
DTR2
DSR2
--CTS1
DTR1
DSR1
--CTS0
DTR0
DSR0
10-6
Pin
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Signal
DCD3
--GND
--DCD2
--GND
--DCD1
--GND
DCD0
--GND
Universal PCI Board User’s Manual
Pin Assignments
CP-114UL
This board supports RS-232, RS-422, and RS-485 (both 2 and 4-wire).
Model
Board Connector
CP-114UL
DB44 (female)
Supported Accessories
CBL-M44M9x4-50
CBL-M44M25x4-50
Serial Connectors
4×DB9 (male)
4×DB25 (male)
DB44 (female): RS-232
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
TxD3
RxD3
RTS3
--TxD2
RxD2
RTS2
--TxD1
RxD1
RTS1
--TxD0
RxD0
RTS0
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal
CTS3
DTR3
DSR3
--CTS2
DTR2
DSR2
--CTS1
DTR1
DSR1
--CTS0
DTR0
DSR0
Pin
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Signal
DCD3
--GND
--DCD2
--GND
--DCD1
--GND
DCD0
--GND
Pin
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Signal
TxD3-(A)
--GND
--TxD2-(A)
--GND
--TxD1-(A)
--GND
TxD0-(A)
--GND
DB44 (female): RS-422, RS-485 (4-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
RxD3+(B)
TxD3+(B)
----RxD2+(B)
TxD2+(B)
----RxD1+(B)
TxD1+(B)
----RxD0+(B)
RxD0-(A)
---
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal
--RxD3-(A)
------RxD2-(A)
------RxD1-(A)
------RxD0-(A)
---
10-7
Universal PCI Board User’s Manual
Pin Assignments
DB44 (female): RS-485 (2-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
Data3+(B)
------Data2+(B)
------Data1+(B)
------Data0+(B)
-----
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal
--Data3-(A)
------Data2-(A)
------Data1-(A)
------Data0-(A)
---
10-8
Pin
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Signal
----GND
------GND
------GND
----GND
Universal PCI Board User’s Manual
Pin Assignments
CP-118U
Port 6
Port 8 Port 7
Port 3
Port 5 Port 4
Port 2 Port 1
21
42
62
1
22
43
GND
GND
GND
GND
GND
GND
This board supports RS-232, RS-422, and RS-485 (both 2 and 4-wire).
Model
Board Connector
CP-118U
DB62 (female)
Supported Accessories
OPT8-M9
CBL-M62M9x8-100 (OPT8D)
OPT8B
CBL-M62M25x8-100 (OPT8C)
Serial Connectors
8×DB9 (male)
8×DB25 (male)
OPT8A, OPT8S
8×DB25 (female)
OPT8-RJ45*
8×RJ45
* The OPT8-RJ45 is designed for RS-232 only. It should only be used with the CP-118U in RS-232
mode.
DB62 (female): RS-232
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Signal
TxD0
DTR0
RxD1
DSR1
DCD1
TxD2
DTR2
RxD3
DSR3
DCD3
RxD4
DSR4
DCD4
TxD5
DTR5
RxD6
DSR6
DCD6
RxD7
DSR7
Pin
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Signal
RxD0
DSR0
DCD0
TxD1
DTR1
RxD2
DSR2
DCD2
TxD3
DTR3
GND
TxD4
DTR4
RxD5
DSR5
DCD5
TxD6
DTR6
GND
TxD7
10-9
Pin
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Signal
CTS0
RTS0
GND
CTS1
RTS1
CTS2
RTS2
GND
CTS3
RTS3
CTS4
RTS4
GND
CTS5
RTS5
GND
CTS6
RTS6
CTS7
RTS7
Universal PCI Board User’s Manual
Pin
21
Signal
DCD7
Pin
42
Pin Assignments
Signal
DTR7
Pin
Signal
Pin
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Signal
----GND
--------GND
--------GND
----GND
---------
DB62 (female): RS-422, RS-485 (4-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Signal
RxD0+(B)
RxD0-(A)
TxD1+(B)
--TxD1-(A)
RxD2+(B)
RxD2-(A)
TxD3+(B)
--TxD3-(A)
TxD4+(B)
--TxD4-(A)
RxD5+(B)
RxD5-(A)
TxD6+(B)
--TxD6-(A)
TxD7+(B)
--TxD7-(A)
Pin
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Signal
TxD0+(B)
--TxD0-(A)
RxD1+(B)
RxD1-(A)
TxD2+(B)
--TxD2-(A)
RxD3+(B)
RxD3-(A)
GND
RxD4+(B)
RxD4-(A)
TxD5+(B)
--TxD5-(A)
RxD6+(B)
RxD6-(A)
GND
RxD7+(B)
RxD7-(A)
10-10
Universal PCI Board User’s Manual
Pin Assignments
DB62 (female): RS-485 (2-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Signal
Data0+(B)
Data0-(A)
------Data2+(B)
Data2-(A)
------------Data5+(B)
Data5-(A)
-------------
Pin
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Signal
------Data1+(B)
Data1-(A)
------Data3+(B)
Data3-(A)
GND
Data4+(B)
Data4-(A)
------Data6+(B)
Data6-(A)
GND
Data7+(B)
Data7-(A)
10-11
Pin
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Signal
----GND
--------GND
--------GND
----GND
---------
Universal PCI Board User’s Manual
Pin Assignments
CP-118U-I
This board supports RS-232, RS-422, and RS-485 (both 2 and 4-wire).
Model
Board Connector
CP-118U-I
DB78 (female)
Supported Accessories
CBL-M78M9x8-100
CBL-M78M25x8-100
Serial Connectors
8×DB9 (male)
8×DB25 (male)
DB78 (female): RS-232
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Signal
GND7
TxD7
--GND6
TxD6
GND5
TxD5
--GND4
TxD4
GND3
TxD3
--GND2
TxD2
GND1
TxD1
--GND0
TxD0
RTS7
DTR7
RTS6
DTR6
--RTS5
Pin
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
Signal
DTR5
RTS4
DTR4
--RTS3
DTR3
RTS2
DTR2
--RTS1
DTR1
RTS0
DTR0
CTS7
DSR7
--CTS6
DSR6
CTS5
DSR5
--CTS4
DSR4
CTS3
DSR3
---
10-12
Pin
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
Signal
CTS2
DSR2
CTS1
DSR1
--CTS0
DSR0
DCD7
RxD7
DCD6
RxD6
--DCD5
RxD5
DCD4
RxD4
--DCD3
RxD3
DCD2
RxD2
--DCD1
RxD1
DCD0
RxD0
Universal PCI Board User’s Manual
Pin Assignments
DB78 (female): RS-422, RS-485 (4-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Signal
GND7
RxD7+(B)
--GND6
RxD6+(B)
GND5
RxD5+(B)
--GND4
RxD4+(B)
GND3
RxD3+(B)
--GND2
RxD2+(B)
GND1
RxD1+(B)
--GND0
RxD0+(B)
--RxD7-(A)
--RxD6-(A)
-----
Pin
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
Signal
RxD5-(A)
--RxD4-(A)
----RxD3-(A)
--RxD2-(A)
----RxD1-(A)
--RxD0-(A)
---------------------------
10-13
Pin
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
Signal
--------------TxD7-(A)
TxD7+(B)
TxD6-(A)
TxD6+(B)
--TxD5-(A)
TxD5+(B)
TxD4-(A)
TxD4+(B)
--TxD3-(A)
TxD3+(B)
TxD2-(A)
TxD2+(B)
--TxD1-(A)
TxD1+(B)
TxD0-(A)
TxD0+(B)
Universal PCI Board User’s Manual
Pin Assignments
DB78 (female): RS-485 (2-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Signal
GND7
Data7+(B)
--GND6
Data6+(B)
GND5
Data5+(B)
--GND4
Data4+(B)
GND3
Data3+(B)
--GND2
Pin
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Signal
Data2+(B)
GND1
Data1+(B)
--GND0
Data0+(B)
--Data7-(A)
--Data6-(A)
----Data5-(A)
---
10-14
Pin
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Signal
Data4-(A)
----Data3-(A)
--Data2-(A)
----Data1-(A)
--Data0-(A)
-------
Universal PCI Board User’s Manual
Pin Assignments
CP-132UL V2, CP-132UL-I V2
These boards support RS-422 and RS-485 (both 2 and 4-wire).
Model
Board Connector
CP-132UL V2
DB25 (female)
CP-132UL-I V2
Supported Accessories
Serial Connectors
CBL-M25M9x2-50
2×DB9 (male)
DB25 (female): RS-422
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Signal
--TxD1-(A)
GND1
CTS1+(B)
TxD1+(B)
----CTS0-(A)
RxD0-(A)
RTS0-(A)
RTS0+(B)
RxD0+(B)
---
Pin
14
15
16
17
18
19
20
21
22
23
24
25
Signal
CTS1-(A)
RxD1-(A)
RTS1-(A)
RTS1+(B)
RxD1+(B)
----TxD0-(A)
GND0
CTS0+(B)
TxD0+(B)
---
DB25 (female): RS-485 (4-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Signal
--TxD1-(A)
GND1
--TxD1+(B)
------RxD0-(A)
----RxD0+(B)
---
Pin
14
15
16
17
18
19
20
21
22
23
24
25
Signal
--RxD1-(A)
----RxD1+(B)
----TxD0-(A)
GND0
--TxD0+(B)
---
10-15
Universal PCI Board User’s Manual
Pin Assignments
DB25 (female): RS-485 (2-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Signal
----GND1
----------Data0-(A)
----Data0+(B)
---
Pin
14
15
16
17
18
19
20
21
22
23
24
25
Signal
--Data1-(A)
----Data1+(B)
------GND0
-------
10-16
Universal PCI Board User’s Manual
Pin Assignments
CP-134U V2, CP-134U-I V2
These boards support RS-422 and RS-485 (both 2 and 4-wire). Ports 1 and 2 also support RS-232.
Model
CP-134U V2
CP-134U-I V2
Board Connector
DB44 (female)
Supported Accessories
CBL-M44M9x4-50
CBL-M44M25x4-50
Serial Connectors
4×DB9 (male)
4×DB25 (male)
DB44 (female): RS-232 (Ports 1 and 2 only)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
----------------TXD1
RXD1
RTS1
--TXD0
RXD0
RTS0
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal
----------------CTS1
DTR1
DSR1
--CTS0
DTR0
DSR0
Pin
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Signal
----------------DCD1
RI1
GND
DCD0
RI0
GND
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal
CTS3+(B)
RXD3-(A)
RTS3-(A)
--CTS2+(B)
RXD2-(A)
RTS2-(A)
--CTS1+(B)
RXD1-(A)
RTS1-(A)
--CTS0+(B)
RXD0-(A)
RTS0-(A)
Pin
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Signal
TXD3-(A)
CTS3-(A)
GND3
--TXD2-(A)
CTS2-(A)
GND2
--TXD1-(A)
CTS1-(A)
GND1
TXD0-(A)
CTS0-(A)
GND0
DB44 (female): RS-422
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
RXD3+(B)
TXD3+(B)
RTS3+(B)
--RXD2+(B)
TXD2+(B)
RTS2+(B)
--RXD1+(B)
TXD1+(B)
RTS1+(B)
--RXD0+(B)
TXD0+(B)
RTS0+(B)
10-17
Universal PCI Board User’s Manual
Pin Assignments
DB44 (female): RS-485 (4-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
RXD3+(B)
TXD3+(B)
----RXD2+(B)
TXD2+(B)
----RXD1+(B)
TXD1+(B)
----RXD0+(B)
TXD0+(B)
---
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal
--RXD3-(A)
------RXD2-(A)
------RXD1-(A)
------RXD0-(A)
---
Pin
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Signal
TXD3-(A)
--GND3
--TXD2-(A)
--GND2
--TXD1-(A)
--GND1
TXD0-(A)
--GND0
Signal
--Data3-(A)
------Data2-(A)
------Data1-(A)
------Data0-(A)
---
Pin
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Signal
----GND3
------GND2
------GND1
----GND0
DB44 (female): RS-485 (2-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
Data3+(B)
------Data2+(B)
------Data1+(B)
------Data0+(B)
-----
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
10-18
Universal PCI Board User’s Manual
Pin Assignments
CP-138U
This board supports RS-422 and RS-485 (both 2 and 4-wire).
Model
CP-138U
Board Connector
DB62 (female)
Supported Accessories
OPT8-M9
CBL-M62M9x8-100 (OPT8D)
OPT8B
CBL-M62M25x8-100 (OPT8C)
Serial Connectors
8×DB9 (male)
8×DB25 (male)
OPT8A, OPT8S, OPT8F, OPT8Z,
8×DB25 (female)
OPT8K, OPT8I
DB62 (female): RS-422, RS-485 (4-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Signal
RxD0+(B)
RxD0-(A)
TxD1+(B)
--TxD1-(A)
RxD2+(B)
RxD2-(A)
TxD3+(B)
--TxD3-(A)
TxD4+(B)
--TxD4-(A)
RxD5+(B)
RxD5-(A)
TxD6+(B)
--TxD6-(A)
TxD7+(B)
--TxD7-(A)
Pin
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Signal
TxD0+(B)
--TxD0-(A)
RxD1+(B)
RxD1-(A)
TxD2+(B)
--TxD2-(A)
RxD3+(B)
RxD3-(A)
GND
RxD4+(B)
RxD4-(A)
TxD5+(B)
--TxD5-(A)
RxD6+(B)
RxD6-(A)
GND
RxD7+(B)
RxD7-(A)
10-19
Pin
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Signal
----GND
--------GND
--------GND
----GND
---------
Universal PCI Board User’s Manual
Pin Assignments
DB62 (female): RS-485 (2-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Signal
Data0+(B)
Data0-(A)
------Data2+(B)
Data2-(A)
------------Data5+(B)
Data5-(A)
-------------
Pin
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Signal
------Data1+(B)
Data1-(A)
------Data3+(B)
Data3-(A)
GND
Data4+(B)
Data4-(A)
------Data6+(B)
Data6-(A)
GND
Data7+(B)
Data7-(A)
10-20
Pin
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Signal
----GND
--------GND
--------GND
----GND
---------
Universal PCI Board User’s Manual
Pin Assignments
CP-138U-I
This board supports RS-422 and RS-485 (both 2 and 4-wire).
Model
Board Connector
CP-138U-I
DB78 (female)
Supported Accessories
CBL-M78M9x8-100
CBL-M78M25x8-100
Serial Connectors
8×DB9 (male)
8×DB25 (male)
DB78 (female): RS-422, RS-485 (4-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Signal
GND7
RxD7+(B)
--GND6
RxD6+(B)
GND5
RxD5+(B)
--GND4
RxD4+(B)
GND3
RxD3+(B)
--GND2
RxD2+(B)
GND1
RxD1+(B)
--GND0
RxD0+(B)
--RxD7-(A)
--RxD6-(A)
-----
Pin
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
Signal
RxD5-(A)
--RxD4-(A)
----RxD3-(A)
--RxD2-(A)
----RxD1-(A)
--RxD0-(A)
---------------------------
10-21
Pin
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
Signal
--------------TxD7-(A)
TxD7+(B)
TxD6-(A)
TxD6+(B)
--TxD5-(A)
TxD5+(B)
TxD4-(A)
TxD4+(B)
--TxD3-(A)
TxD3+(B)
TxD2-(A)
TxD2+(B)
--TxD1-(A)
TxD1+(B)
TxD0-(A)
TxD0+(B)
Universal PCI Board User’s Manual
Pin Assignments
DB78 (female): RS-485 (2-wire)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Signal
GND7
Data7+(B)
--GND6
Data6+(B)
GND5
Data5+(B)
--GND4
Data4+(B)
GND3
Data3+(B)
--GND2
Pin
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Signal
Data2+(B)
GND1
Data1+(B)
--GND0
Data0+(B)
--Data7-(A)
--Data6-(A)
----Data5-(A)
---
10-22
Pin
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Signal
Data4-(A)
----Data3-(A)
--Data2-(A)
----Data1-(A)
--Data0-(A)
-------
Universal PCI Board User’s Manual
Pin Assignments
CP-168U V2
This board supports RS-232. With the OPT8F or OPT8Z accessory, it can support RS-422. With the
OPT8K or OPT8I accessory, it can support RS-422 and RS-485 (both 2 and 4-wire).
Model
Board Connector
CP-168U V2
DB62 (female)
Supported Accessories
OPT8-M9
CBL-M62M9x8-100 (OPT8D)
OPT8B
CBL-M62M25x8-100 (OPT8C)
Pin
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
8×DB25 (male)
8×RJ45
DB62 (female): RS-232
Signal
TxD0
DTR0
RxD1
DSR1
DCD1
TxD2
DTR2
RxD3
DSR3
DCD3
RxD4
DSR4
DCD4
TxD5
DTR5
RxD6
DSR6
DCD6
RxD7
DSR7
DCD7
8×DB9 (male)
OPT8A, OPT8S, OPT8F, OPT8Z,
8×DB25 (female)
OPT8K, OPT8I
OPT8-RJ45
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Serial Connectors
Signal
RxD0
DSR0
DCD0
TxD1
DTR1
RxD2
DSR2
DCD2
TxD3
DTR3
GND
TxD4
DTR4
RxD5
DSR5
DCD5
TxD6
DTR6
GND
TxD7
DTR7
10-23
Pin
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Signal
CTS0
RTS0
GND
CTS1
RTS1
CTS2
RTS2
GND
CTS3
RTS3
CTS4
RTS4
GND
CTS5
RTS5
GND
CTS6
RTS6
CTS7
RTS7
Universal PCI Board User’s Manual
Pin Assignments
POS-104UL
This board supports RS-232 only.
Model
POS-104UL
Board Connector
DB44 (female)
Supported Accessories
CBL-M44M9x4-50(POS)
Serial Connectors
4×DB9 (male)
DB44 (female): RS-232
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
TxD3
RxD3
RTS3
5V/12V/RI3
TxD2
RxD2
RTS2
5V/12V/RI2
TxD1
RxD1
RTS1
5V/12V/RI1
TxD0
RxD0
RTS0
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal
CTS3
DTR3
DSR3
--CTS2
DTR2
DSR2
--CTS1
DTR1
DSR1
--CTS0
DTR0
DSR0
10-24
Pin
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Signal
DCD3
--GND
--DCD2
--GND
--DCD1
--GND
DCD0
5V/12V/RI0
GND
Universal PCI Board User’s Manual
Pin Assignments
Serial Connectors
DB9 (male)
The following accessories provide DB9 (male) serial connectors for your UPCI board:
Accessory
CBL-M25M9x2-50
Board Connector Serial Connectors
DB25 (female)
2×DB9 (male)
CBL-M44M9x4-50
DB44 (female)
4×DB9 (male)
CBL-M44M9x4-50(POS)
CBL-RJ45M9-150
OPT8-M9
CBL-M62M9x8-100 (OPT8D)
CBL-M78M9x8-100
DB44 (female)
RJ45
4×DB9 (male)
4×DB9 (male)
DB62 (female)
8×DB9 (male)
DB78 (female)
8×DB9 (male)
1
6
5
9
The pin assignments for the DB9 (male) serial connector are shown below. There are different pin
assignments depending on the serial interface that your board is configured for.
RS-422
RS-485 (2W)
RS-485 (4W)
1
DCD
TxD-(A)
--2
RxD
TxD+(B)
--3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
----7
RTS
----8
CTS
----9
*5V/12V/RI
----* The 5V/12V/RI signal only applies to the POS-104UL
Pin
RS-232
10-25
Universal PCI Board User’s Manual
Pin Assignments
DB25 (male)
The following accessories provide DB25 (male) serial connectors for your UPCI board:
Accessory
CBL-M44M25x4-50
Board Connector Serial Connectors
DB44 (female)
4×DB25 (male)
CBL-RJ45M25-150
RJ45
4×DB25 (male)
DB62 (female)
8×DB25 (male)
DB78 (female)
8×DB25 (male)
OPT8B
CBL-M62M25x8-100 (OPT8C)
CBL-M78M25x8-100
1
13
14
25
The pin assignments for the DB25 (male) serial connector are shown below. There are different pin
assignments depending on the serial interface that your board is configured for.
Pin
RS-232
2
3
4
5
6
7
8
20
TxD
RxD
RTS
CTS
DSR
GND
DCD
DTR
RS-422
RS-485 (4W)
RxD+(B)
TxD+(B)
------GND
TxD-(A)
RxD-(A)
10-26
RS-485 (2W)
Data+(B)
--------GND
--Data-(A)
Universal PCI Board User’s Manual
Pin Assignments
DB25 (female)
The following accessories provide DB25 (female) serial connectors for your UPCI board:
Accessory
Board Connector Serial Connectors
OPT8A, OPT8S, *OPT8F,
DB62 (female)
8×DB25 (female)
*OPT8Z, *OPT8K, *OPT8I
* The OPT8F, OPT8Z, OPT8K, and OPT8I are designed for use with the CP-168U V2 only.
13
1
25
14
The pin assignments for the DB25 (female) serial connector are shown below. There are different
pin assignments depending on the serial interface that your board is configured for.
OPT8A, OPT8S
Pin
RS-232
2
3
4
5
6
7
8
20
RxD
TxD
CTS
RTS
DTR
GND
DCD
DSR
RS-422
RS-485 (4W)
TxD+(B)
RxD+(B)
----RxD-(A)
GND
TxD-(A)
---
OPT8F, OPT8Z, OPT8K, OPT8I
Pin
2
3
7
14
16
RS-422
RS-485 (4W)
RxD+(B)
TxD+(B)
GND
RxD-(A)
TxD-(A)
RS-485 (2W)
Data+(B)
--GND
Data-(A)
---
10-27
RS-485 (2W)
--Data+(B)
----Data-(A)
GND
-----
Universal PCI Board User’s Manual
Pin Assignments
RJ45
The following accessories provide RJ45 serial connectors for your UPCI board:
Accessory
OPT8-RJ45
1
Board Connector Serial Connectors
DB62 (female)
8×RJ45
8
The pin assignments for the RJ45 serial connector are shown below. Only RS-232 is supported. The
OPT8-RJ45 accessory should only be used with the CP-118U in RS-232 mode or with the CP-168U
V2.
Pin
1
2
3
4
5
6
7
8
RS-232
DSR
RTS
GND
TxD
RxD
DCD
CTS
DTR
10-28
Download PDF