DMC | TSC-35/RU | User manual | DMC TSC-35/RU User manual

V PANEL
104 / 121 / 150 / 170 / 190
User manual
Rel. 08.2005 Ver.01
0-0096-3132
The German version of this manual is not available.
Die deutsche Version ist nicht verfügbar.
V Panel 104 / 121 / 150 / 170 / 190
User Manual
Manual History
Date
Aug.2005
Version
01
Changes
First edition
Kontron Embedded Computers GmbH
Werner-von-Siemens-Str. 1
93426 Roding
Phone:
+49 9461 950 -0
Fax:
+49 9461 950 -100
e-mail:
sales@kontron.com
Internet:
http://www.kontron.com
© Copyright Kontron Embedded Computers GmbH 2005. All rights are reserved
2
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
COPYRIGHT
Copyright Kontron Embedded Computers
All rights are reserved
No part of this product, including the product and software may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the express written permission of
Kontron Embedded Computers GmbH (herinafter referred to as Kontron) except documentation kept by the purchaser for backup purposes.
TRADEMARKS
All trademarks mentioned in this manual are registered properly of the respective owners.
CE-CONFORMITY
The following requirements, standards, specifications constitute part of the declaration:
EN 55022 class A
EN 55024
EN 60950
EN 61000-3-2
EN 61000-3-3 EN 61000-6-2
The validation of this declaration depends on the properly use of the product.
FCC Class A Radio Frequency
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to 1/47 CFR Part 15.109 Class A of FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference
that may cause undesired operation.
The limits of FCC Part15 class A are designed to provide reasonable protection
against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interferhttp://www.kontron.com
3
V Panel 104 / 121 / 150 / 170 / 190
User Manual
ence to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by more of one or more of the following measures:
1. Reorient or relocate the receiving antenna
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
4. Consult the dealer or an experienced radio/television technican for help.
Notice1: The changes or modifications not expressly approved by the party
responsible for compliance could void the user`s authority to operate the equipment.
Notice2: Shielded interface cables, if any, must be used in order to comply with
emission limits.
CAUTION !
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
4
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
Table of contents
Copyright .................................................................................................... 3
Trademarks ................................................................................................ 3
CE-Conformity ............................................................................................ 3
1. Introduction ................................................................................................. 6
2. Overview .................................................................................................... 8
3. Hardware Installation ................................................................................... 9
3.1 Connect external devices ................................................................ 9
3.2 Connect internal devices ............................................................... 11
3.3 Internal Jumper setting .................................................................. 12
3.4 LED Status indicators .................................................................... 14
4 Software installation .................................................................................. 15
4.1 Application software and operating system ................................... 15
4.2 Hardware drivers ........................................................................... 15
5. Technical Details ....................................................................................... 23
5.1 Mechanical .................................................................................... 23
5.2 Electronical ................................................................................... 23
5.3 Environment ................................................................................. 24
5.4 CE Directives and Standards ........................................................ 24
5.5 Connector pinout ........................................................................... 24
5.6 Options ......................................................................................... 31
5.7 Block diagram ............................................................................... 33
6.
Maintenance ........................................................................................ 34
6.1 Customer service ........................................................................... 34
6.2 Cleaning ........................................................................................ 34
6.3 Return and repair .......................................................................... 34
6.4 Packaging ...................................................................................... 35
7.
Troubleshooting ................................................................................... 36
7.1 FAQ ............................................................................................... 36
8.
Disposal ............................................................................................... 36
9.
Appendix .............................................................................................. 36
http://www.kontron.com
5
V Panel 104 / 121 / 150 / 170 / 190
User Manual
1. INTRODUCTION
1.1. APPROPRIATE USE
The main purpose of the V Panel is the use and operation with 24VDC-powersources.
The surrounding area of the Panel are dry rooms.
The Panel is intended for industrial applications in machine and plant control
engineering.
The user is not entitled to change the system components or open the body
without consultation to Kontron.
1.2 ITEM CHECKLIST
Your Panel comes securely packaged in solid shipping carton(s). Upon receiving your Panel, open the carton(s) and remove the contents carefully.
The shipping carton should contain the following items:
- V Panel 10,4” 12,1” 15” 17” or 19”
- CPU Support CD (optional)
- 24V DC Power cord (optional)
- This user manual (optional)
- Software installation CD if implemented
Carefully inspect each component to ensure that nothing is missing and/or
damaged. If any of these items is missing or damaged, please contact Kontron
immediately. Preserve of of the packing material for future transportation.
1.3 IMPORTANT SAFETY INSTRUCTIONS
This section gives you detailed information about how to maintain a safe
environment while using the Panel. You can maintain its condition and performance by following these guidelines. Please read it carefully to ensure maximum safety.
Be careful about the power supply input voltage. The Panel has specific
power requirements.
Please prevent the Panel from humidity.
Never pour any liquid on the Panel, this may cause fire or electrical shock.
Place the Panel on a reliable surface when installing. A drop or fall may cause
damage.
6
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
Do not leave the Panel in an unconditional environment. Storage temperature
above 70°C may damage the Panel.
The opening on the enclosure are for air convection, protect the Panel from
overheating.
DO NOT COVER THE OPENINGS
If the Panel is not in use for a long time, disconnect it from mains to avoid
possible damage by transient overvoltage.
If you had to open the housing of the Panel in service cases, all single parts of
the plant must first be switched off, after which the Panel can be disconnected
from the plant. Secure each part against accidentally switched on during service.
Following service activities on the Panel could cause failures.
• Metal objects such as screws or tools fall on or in the Panel
• Cables are removed or inserted during operation.
• Plug-in cards are removed or inserted during the Panel is
switched on.
All cautions and warnings on the Panel should be noted.
The system has to shut down and checked immediately by service staff, if one
of the following situation appears:
• The power cord or plug is damaged.
• Liquid has penetrated the Panel.
• The Panel is exposed to moisture.
• Obvious sign of breakage are visible.
• System did not work properly or you can not get it work
according to the application requirements.
http://www.kontron.com
7
V Panel 104 / 121 / 150 / 170 / 190
2.
User Manual
OVERVIEW
The Kontron V Panel computer is a high performance system. The compact
design enables an integration even under the condition of very restricted spaces.
Our 100% industiy capable, scalable Panel meet the highest requirements
concerning shock, vibration and temperature resistance. The system also
provides a high resistance under tough EMC conditions.
Features:
- Display sizes 10,4“ 12,1“ 15” 17” and 19”
- Display type TFT active Matrix LCD with resistive touch.
- Color depth up to 32 bit
- Max. Resolution 1280x 1024
- Intel Pentium M Processor up to 1.1 Ghz
- Main memory up to 1024 MB on SDRAM
- Standard interfaces 3x USB, 2x PS/2, 1x LPT, 2x LAN, 4x RS232
- Input power of 24 VDC
- Installation of two PCI extension cards.
- Front side protection in IP65 (conform to EN 60529)
- Operating temperature up to 50°C
- Operating system Windows and Linux
- Dimension 10.4” 295mm x 348mm x 121mm
12.1” 327mm x 400mm x 121mm
15.0” 362mm x 452mm x 123mm
17.0” 390mm x 465mm x 130mm
19.0” 426mm x 516mm x 135mm
- All connectors build for industrial standards
- Shock and vibration tested
- Embedded architecture long-life electronic components
- Optional:Stainless steel front, front USB, Power ON switch, power LED
8
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
3.
HARDWARE INSTALLATION
Attention!
The weight of the Panel is about 7kg
Carry it on with both hands!
The Panel of this type is developed to work in a control cabinet. Thereby it must
be pointed that all the environmental conditions must be considered.
When installing the Panel take care that there is enough area for ventilations on
rear side. For details go to item housing dimensions.
If your Panel was delivered without software install a keyboard and mouse.
If operating system and software is installed, the touch is working and calibrated.
Look up for further settings e.g. BIOS on the ETX board manuals.
3.1 CONNECT EXTERNAL DEVICES
To get detailed information about pinout of each connector please look to chapter
“technical details”.
MOUSE
Fieldb us
POWER - ON
COM 3
LAN 1
LPT
HDD
POWER
KEYBOARD
USB
COM 1
CRT
COM 2
LAN 2
RESET
POWER
Fig. 3-1
3.1.1 PS/2 Keyboard and Mouse
Use this connector to connect PS/2 mouse and keyboard.
3.1.2 LAN1 Port
This connector provides a external interfaces 10/100 BaseT on RJ45 to connect
your Panel to other devices in a network.
http://www.kontron.com
9
V Panel 104 / 121 / 150 / 170 / 190
User Manual
3.1.3 USB port
This connector provides two external USB 2.0 interfaces
3.1.4 Parallel port LPT
Use this port to connect a printer or other parallel devices.
3.1.5 Serial Interface COM1, COM2, COM3
Three serial interfaces enables you to connect a external device with 9 pin
DSUB connector such as mouse or modem. COM2 is selectable as a input for
programming fielbuscontroller.
3.1.6 Fieldbus interface CAN / CANOpen / Profibus / DeviceNet
External connector of internal fieldbus controller. Interface to connect CAN,
CANOpen, Profibus/MPI or DeviceNet devices. All interfaces in master or
slave configuration available.
3.1.7 CRT Monitor
Connector and interface to VGA/CRT monitor .
3.1.8 Second LAN2 Port
This connector provides a second external interfaces 10/100/1000 BaseT on
RJ45 connector to your panel to other devices in a network.
3.1.9 Reset
Reset Switch reset the hole unit.
3.1.10 Main power IN
Use this connector to connect the power supply of 24VDC. Please note the
Power requirements (See chapter technical details).
3.1.11 Power ON button
Enables you to switch on and off the main system.
3.1.13 Front USB
Use this port behind a cover to connect USB devices direct on the panel front
10
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
3.2 CONNECT INTERNAL DEVICES
The panel provides additional functions which could be implemented in the
system by adding cards or changing the configuration of your Panel.
CF
ETX CPU Module
Fig. 3-2
http://www.kontron.com
11
V Panel 104 / 121 / 150 / 170 / 190
Connector
J3
J4
J6
J12
J13
J15
J16
J17
J18
J21
J24
J25
J26
J29
J30
J31/J32
J34
J36
User Manual
Interface
Serial port COM3
Serial port COM4
Backlight interface
Advanced power button interface
External battery connector
Internal Fieldbus interface
Floppy disk drive interface
Secondary IDE Compact flash
Primary IDE Connector UDMA33
IrDA/FIR connector
PCI extension card
PCMCIA
Internal HDD power interface
4-5 wire Tochconnector
DMC touchcontroller interface (option)
Internal USB interfaces
Speaker interface
ATX Power button
3.3 INTERNAL JUMPER SETTING
To identify the jumper location please look to the board layout in Fig.3.2. All
described functions refers to the implemented baseboard.
3.3.1 Backlight supply voltage
3.3.2 Voltage supplied to display
6
5
4
1
2
3
1
Display supply voltage
3V
5V
12V
3.3.3 Address range NVSRAM Switch DIP1
Setting SW1 DIP1
OFF
ON
J8
SW1
ON
Setting
1-6 (default)
2-5
3-4
J5
Backlight supply voltage
12V
5V
OFF
Setting
1-2 (default)
2-3
NVSRAM address
CC000 – CFFFF (Hex)
D0000 – D7000 (Hex)
*TO ENABLE THE NVSRAM DIP8 ON SW1 MUST BE SET TO OFF. IF SJA1000 CHIP SIS POPULATED DIP2 ON SW1 MUST BE SET TO OFF.
12
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
3.3.4 Address range fielbus controller EC1
3.3.5 Fieldbus Contrl. SJ1000 Interrupt (optional)
DIP4
OFF
OFF
ON
ON
OFF
OFF
ON
ON
DIP5
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Interrupt request
IRQ3
IRQ4
IRQ5
IRQ7
IRQ10
IRQ11
No fieldbus installed
No interrupt
3.3.6 Fieldbus Contrl. SJ1000 IO Address (optional)
Setting SW1
DIP6
OFF
OFF
OFF
OFF
ON
ON
ON
ON
DIP7
OFF
OFF
ON
ON
OFF
OFF
ON
ON
DIP8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
http://www.kontron.com
SW2
SW2
Funktion Compact Flash
Powerbutton J12 disabled
Powerbutton J12 enabled
3.3.10 Configuration USB Port 2
Setting SW2 DIP4
OFF (default)
ON
1
Function Compact Flash
COM2
Input for external programming EC1
3.3.9 Function front power bottom
Setting SW2 DIP3
OFF
ON (default)
SW2
Function Compact Flash
Master
Slave
3.3.8 I/O configuration of COM2
Setting SW2 DIP2
OFF (default)
ON
SW1
IO-address
IRQ3
IRQ4
IRQ5
IRQ7
IRQ10
IRQ11
No fieldbus installed
No interrupt
3.3.7 Master-Slave configuration of Compact Flash
Setting SW2 DIP1
OFF (default)
ON
SW1
OFF
Setiing SW1
DIP3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
SW1
Base address fielbus contr. EC1
CA000 – CBFFF (Hex)
DA000 – DB000 (Hex) and
SJA1000 fieldbuscontroller populated
ON
Setting SW1 DIP2
ON
OFF
SW2
Funktion Compact Flash
USB Port 2 enabled
USB Port 2 disabled
13
V Panel 104 / 121 / 150 / 170 / 190
OFF
ON
SW3
OFF
Setting SW3 DIP1
OFF
ON
SW3
1
ON
3.3.11 Communication port to touchcontroller
User Manual
1
Communication port COM
COM1
COM4
3.3.12 Touch wire configurationr
3.3.13 Output configuration USB Port 0
Setting SW4 DIP1
OFF (default)
ON
SW4
OFF
Touchtype
5 wire
4 wire
ON
Setting SW3 DIP2
OFF
ON
1
USB Port 0
External Connector J22
Internal Connector J31
3.3.14 Output configuration USB Port I
Setting SW4 DIP2
OFF (default)
ON
SW4
USB Port 1
External Connector J22
Internal Connector J31
3.4 LED STATUS INDICATORS
3.3.1 Power LED
Description
POWER
D16 bottom
ON green
POWER OK
OFF
No power
3.3.2 HDD LED
D16 top
Description
HDD activity
ON red
Datatranfer from/to HDD
OFF
No access
3.3.3 Fieldbus status
Status including possible fieldbus modules
Baseboard LED D18
Top Ready Bottom
(yellow)
RUN
(green)
Flashing
OFF
irregular
Flashing
cyclic
OFF
ON
Flashing
irregular
Flashing
cyclic
Flashing
cyclic
Flashing
cyclic
ON
ON
ON
ON
ON
ON
ON
14
CanOpen and
Profibus Module
ERROR
Status
D1
D2
DeviceNet Indicated Status
Module
ERROR
D3
OFF
OFF
OFF
Fieldbus hardware error
OFF
OFF
OFF
Bootstraploader active
OFF
OFF
RED
No slave or fieldbus not connected
OFF
ON
-
PC applikation not redy
ON
OFF
-
Short circuite at fieldbus
ON
ON
RED
No slave or fielbus not connected
ON
ON
RED
At least one slave is missing
OFF
ON
GREEN
Communication is running faultless
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
4 SOFTWARE INSTALLATION
4.1 APPLICATION SOFTWARE AND OPERATING SYSTEM
The panel is designed to work with different operating systems. To install
operating system or application software follow the installation instructions of
the software.
4.2 HARDWARE DRIVERS
On preinstalled systems no drivers had to be installed by a technican or user. If
no operating system was installed, you had to install drivers for the implemented
hardware to get full function of the panel. All the drivers are stored on the
provided Support CD. Drivers also available at the online support at
http://www.kontron.com.
If you need additional help please contact Kontron customer service.
4.2.1 Install Touch driver
Installed touch controllers
Installed Touch
Elo touchcontroller
DMC touchcontroller
10,4”
SS ALU
X
X
12,1”
SS ALU
X
X
15”
SS ALU
X
X
17”
SS ALU
X
X
19”
SS ALU
X
X
SS=stainless steel Front bezel , ALU= Aluminium Front bezel
Preparations of system
Before installing the driver please check the following items.
- USB Port in BIOS enabled
- USB Port driver for operating system installed.
- Device for loading the drivers is installed
- Optional: download driver from WEB
Install DMC touch driver
Installation procedure
To start driver installation please go to the folder where all the driver files are
stored. Start driver installation by double click on file “SETUP.exe” in the
respective folder. Confirm each opened window with “NEXT” when choice is
done. Please observe that during installation no error occurs.
http://www.kontron.com
15
V Panel 104 / 121 / 150 / 170 / 190
User Manual
>>Start installation and set folder
>>Choose your destination folder
16
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
>>Choose display of touch icon in
system tray
>>Select installed touch controllers
Value: 1
>>Select spread of touch on display
Value line 1:“Whole Desktop”
Value line 2:“Device1”
http://www.kontron.com
17
V Panel 104 / 121 / 150 / 170 / 190
User Manual
>> Select controler type
Value: DMC TSC-10 Series USB
>> Installation
Calibration
To get the according touch function you had to calibrate the touch.
To do this go to START/Programs/DMC/ Calibrate
Do the calibration with a touch stick on the displayed arrows.
Install ELO touch driver
Installation procedure
To start driver installation please go to the folder where the driver files are
stored. Start driver installation by double click on file “SW500930.exe” in the
respective folder. Confirm each opened window with “OK” or “NEXT” when
choice is done.
Please observe that during installation no error occurs.
18
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
>> Choose your destination
folder to extract files
>> Select touch type
“USB touchsreen “
http://www.kontron.com
19
V Panel 104 / 121 / 150 / 170 / 190
User Manual
>>Confirm licence agreement
>>Start touch calibration
20
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
After complete installation and calibration of touch you find a new icon in the
control panel to set additional features.
4.2.2 Install EC1 fieldbus driver
Basically your system is perpared as one of the possible fieldbus interfaces.
That means that the firmware of the controller inside is programmed, and the
needed fieldbus module is mounted.
To get access from your operating system to this controller you had to install
the so called CIF device driver.
You find this driver on the provided Hilscher system software CD in the folder
DRIVER.
Start installation with program SETUP.EXE at this folder.
http://www.kontron.com
21
V Panel 104 / 121 / 150 / 170 / 190
User Manual
>>Select your destination
folder
>> Choose your program
description
22
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
5. TECHNICAL DETAILS
5.1 MECHANICAL
Features
V Panel
Model
104
121
Display size
10,4“
12.1”
Dimension 295 x 348 x 121mm
327 x 400 x 121mm
panelmount
HxWxD
Front Bezel ALU or stainless steel optional
Weight
6,6 kg
8 kg
Protection class IP65 Front (NEMA 250 type 12 and 13)
150
15”
362 x 452 x 123mm
170
17”
390 x 465 x 130mm
190
19”
426 x 516 x 135mm
9,85kg
11,7kg
13,4kg
5.2 ELECTRONICAL
Features
Model
Max. resolution
Brightness
Front Bezel
Touch screen
Function keys
Processor
Main memory
External interfaces
Free Slots
Field Buses
Internal Drives
Drives side
accessible
Verified OS
Power Supply
Power consum.
I max
Battery
MTBF
V Panel
104
121
150
170
800 x 600
800 x 600
1024 x 768
1280 x 1024
2
2
2
2
350CD /m
350CD /m
250CD /m
250CD /m
ALU or stainless steel optional
Resistive analog
Optional 16 up to 112 freely programmable keys
Intel Celeron 600 MHz
Intel Pentium M 1.1 GHz
Up to 1024 Mbyte
3x USB (1xfront, 2x rear side); 2x PS/2; 1x LPT; 1x LAN 10/100; 1x LAN 100/1000; 4x RS232
2x PCI, PCMCIA slot optional
CANopen or DeviceNet or Profi bus or CAN
CompactFlash up to 2 GByte, HDD optional
HDD
190
1280 x 1024
2
250CD /m
Windows XP, Windows XP embedded, Linux
24 VDC +/- 20% with protection against reverse polarity.
62W
3,32 W
External Lithium 3,5V 750mAh
< 40000 h (excluding backlight tube)
http://www.kontron.com
23
V Panel 104 / 121 / 150 / 170 / 190
User Manual
5.3 ENVIRONMENT
Features
V Panel all models
Temperature Operating: 0° to +50°C
Storage: -25° to +70°C
Humidity Operation: 5 to 95% non condensino
Storage: 5 to 95% non condensing
Cooling Fanless cooling concept
Shock acc. DIN Operating: 15G, 11ms duration
EN 60068-2-27 Storage: 50G, 11ms duration (half-sinus)
Vibration acc. DIN Operating: 10000 ft (3,048m)
EN 60068-2-27 Storage: 15000 ft (4,622m)
Altitude Operating: 10-500 Hz: 1G / 3 axis
Storage: 10-500 Hz: 2G / 3 axis
5.4 CE DIRECTIVES AND STANDARDS
Features
V Panel all models
EMC US: FCC47 CFR PART 15; Class A level
CE: EN61000-6-2; EN55022/A (CISPR22)l
Approvals CE, FCC, cULus
RoHS Compliant Yes
5
3
6
4
10
12
2
8
1
7
11
PS/2 Keyboard/Mouse Connector
9
5.5 CONNECTOR PINOUT
Keyboard
PIN
1
3
5
Signal Name
KBDATA#
GND
KBCLK#
PIN
2
4
6
Signal Name
NC
VCC
NC
PIN
8
10
12
Signal Name
NC
VCC
NC
PIN
2
4
6
8
Signal Name
TXNC
RXNC
PIN
B1
B2
B3
B4
Signal Name
VCC
DataData+
Gnd
Mouse
8
1
LAN + Dual USB Combo Connector
A1
Signal Name
MSDATA#
GND
MSCLK#
B1
PIN
7
9
11
LAN
PIN
1
3
5
7
Signal Name
TX+
RX+
NC
NC
USB
PIN
A1
A2
A3
A4
24
Signal Name
VCC
DataData+
Gnd
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
LPT
13
1
25
LPT, COM1, COM2, VGA Connector
1
14
1
5
10
6
11
9
COM
CRT
LPT
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
Signal Name
Strobe#
Data 1
Data 3
Data 5
Data 7
BUSY#
SELECT
ERROR#
SLIN#
GND
GND
GND
GND
PIN
2
4
6
8
10
12
14
16
18
20
22
24
Signal Name
Data 0
Data 2
Data 4
Data 6
ACK#
PE
AFD#
INIT#
GND
GND
GND
GND
PIN
2
4
6
8
Signal Name
RXD ( Receive data)
DTR (Data terminal ready)
DSR(Data set ready)
CTS (Clear to send)
PIN
2
4
6
8
10
12
14
Signal Name
Green
NC
CRTGND
CRTGND
CRTGND
DDCDAT
VSYNC
COM
PIN
1
3
5
7
9
Signal Name
DCD ( Data Carrier Detect)
TXD ( Transmit Data)
GND
RTS (Request to send)
RI (Ring indicator)
CRT
PIN
1
3
5
7
9
11
13
15
Signal Name
RED
Blue
CRTGND
CRTGND
VCC
NC
HSYNC
DDCCLK
LAN2 Port
8
1
PIN
1
2
Signal Name when 82541ER loaded 10/100/1000 Base T
Signal name when 82551xx loaded 10/100 BaseT
MX_0+
MX_0-
TXD+
TXD-
3
4
5
MX_1+
MX_2+
MX_2-
RXD+
NC
NC
6
7
8
MX_1MX_3+
MX_3-
RXDNC
NC
http://www.kontron.com
25
V Panel 104 / 121 / 150 / 170 / 190
User Manual
Power Connector
PIN
1
2
3
1
3
Signal Name
GND
NC
24V IN
RS232 Connector
Signal Name
DCD (Data Carrier Detect)
RXD (Receive Data)
TXD (Transmit Data)
DTR (Data Terminal Ready)
GND
DSR (Data Set Ready)
RTS (Request To Send)
CTS (Clear To Send)
RI (Ring Indicator)
J34
PIN
3
4
Serial port COM3 , COM4
PIN
1
3
5
7
9
Signal Name
DCD (Data Carrier Detect)
RXD (Receive Data)
TXD (Transmit Data)
DTR (Data Terminal Ready)
GND
Backlight interface
PIN
1
2
3
4
5
26
Signal Name
DSR (Data Set Ready)
RTS (Request To Send)
CTS (Clear To Send)
RI (Ring Indicator)
POWER (+12V)
J6
1
J12
1
Signal Name
Backlight Inverter supply voltage
GND
Brightness Control (0V max. Brightness, 5V min. Brightness)
Brightness Control (12V max. Brightness, 6V min. Brightness)
Enable
Advanced power button interface
PIN
1
2
3
4
J3
PIN
2
4
6
8
10
1
Signal Name
GND
VCC
1
Signal Name
Speaker
NC
2
PIN
1
2
9
Speaker interface
10
PIN
1
2
3
4
5
6
7
8
9
Signal Name
+3V STANDBY
GND
LED+
LED-
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
External battery connector
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
Signal Name
GND
GND
NC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
NC
GND
NC
http://www.kontron.com
J16
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
9
1
2
1
Floppy disk drive interface
Signal Name
STATUS
CAN TX
PROFIBUS TX
ERROR
+12V
2
PIN
2
4
6
8
10
33
Signal Name
+5V
CAN RX
PROFIBUS RX
PROFIBUS ENABLE
GND
J15
10
Signal Name
GND
NC
NC
V_BAT
Internal Fieldbus interface
PIN
1
3
5
7
9
1
34
PIN
1
2
3
4
J13
Signal Name
DENSEL#
NC
NC
FDINDEX# (Index)
FDMOTEA# (Motor Enable A)
FDDRVSB# (Drive Select B)
FDDRVSA# (Drive Select A)
FDMOTEB# (Motor Enable B)
FDDIR# (Stepper Motor Direction)
FDSTEP# (Step Pulse)
FDWD# (Write Data)
FDWG# (Write Enable)
FDTRK0# (Track 0)
FDWPD# (Write Protect)
FDRD# (Read Data)
FDSIDE# (Side 1 Select)
DSKCHG# (Diskette Change)
27
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
28
Signal Name
RESET#
Data 7
Data 6
Data 5
Data 4
Data 3
Data 2
Data 1
Data 0
GND
DRQ#
IOW#
IOR#
IORDY
ACK#
IRQ
ADDR1
ADDR0
CS0#
Active#
+5V
GND
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
1
2
Primary IDE Connector UDMA33 J18
Signal Name
NC
Data 11
Data 12
Data 13
Data 14
Data 15
CS1#
NC
IOR#
IOW#
VCC
IRQ
VCC
M#/S (Compact Flash)
NC
RESET#
IORDY
REQ#
ACK#
Active#
DIAG
Data 8
Data 9
Data 10
GND
43
PIN
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
44
Signal Name
GND
Data 3
Data 4
Data 5
Data 6
Data 7
CS0#
GND
GND
GND
GND
GND
VCC
GND
GND
GND
GND
ADDR2
ADDR1
ADDR0
Data 0
Data 1
Data 2
NC
NC
50
1
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
25
Secondary IDE Compact flash J17
User Manual
24
V Panel 104 / 121 / 150 / 170 / 190
Signal Name
GND
Data 8
Data 9
Data 10
Data 11
Data 12
Data 13
Data 14
Data 15
NC
GND
GND
GND
GND
GND
NC
PDIAG
ADDR2
CS1#
GND
+5V
NC
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
IrDA/FIR connector
PIN
1
2
3
4
5
J21
Signal Name
+5V
NC
IRRX
GND
IRTX
PCI Edge card Master connector
PIN
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
1
Signal Name
NC
+12V
NC
NC
+5V
INTA#
INTC#
+5V
NC
+5V (I/O)
NC
GND
GND
GNT1#
RESET#
+5V (I/O)
GNT0#
GND
REQ2#
AD30
+3.3V
AD28
AD26
GND
AD24
NC
+3.3V
AD22
AD20
GND
AD18
PIN
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
Signal Name
-12V
NC
GND
NC
+5V
+5V
INTB#
INTD#
NC
REQ1#
NC
GND
GND
PCICLK1
GND
PCICLK2
GND
REQ0#
+5V (I/O)
AD31
AD29
GND
AD27
AD25
+3.3V
CBE3#
AD23
GND
AD21
AD19
+3.3V
http://www.kontron.com
J24
PIN
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
A51
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
Signal Name
AD16
+3.3V
FRAME#
GND
TRDY#
GND
STOP#
+3.3V
NC
NC
GND
PAR
AD15
+3.3V
AD13
AD11
GND
AD09
Key
Key
CBE0#
+3.3V
AD06
AD04
GND
AD02
AD00
+5V (I/O)
NC
+5V
+5V
PIN
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B50
B51
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
Signal Name
AD17
CBE2#
GND
IRDY#
+3.3V
DEVSEL#
GND
LOCK#
PERR#
+3.3V
SERR#
+3.3V
CBE1#
AD14
GND
AD12
AD10
GND
Key
Key
AD08
AD07
+3.3V
AD05
AD03
GND
AD01
+5V (I/O)
NC
+5V
+5V
29
V Panel 104 / 121 / 150 / 170 / 190
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Signal Name
GND
AD0_Data 3
AD1_Data 4
AD3_Data 5
AD5_Data 6
AD7_Data 7
C/BE0#_CE1
AD9_A10
AD11_OE#
AD12_A11
AD14_A9
C/BE1#_A8
PAR_A13
PERR#_A14
GNT_WE
INTX_READY_IREQ
AVCC
AVCCP
CLK_A16
IRDY#_A15
C/BE2X_A12
AD18_A7
AD20_A6
AD21_A5
AD22_A4
AD23_A3
AD24_A2
AD25_A1
AD26_A0
AD27_Data 0
AD29_Data 1
RSVD_Data 2
CLKRUN_WP_IOCS16#
GND
Internal HDD power interface
PIN
1
2
3
4
30
Signal Name
GND
CD1
AD2_Data 11
AD4_Data 12
AD6_Data 13
RSVD_Data 14
AD8_Data 15
AD10_CE2
VS1
AD13_RSVD_IOR#
AD15_RSVD_IOW#
AD16_A17
RSVD_A18
LOCK#_A19
STOP#_A20
DEVSEL#_A21
AVCC
AVCCP
TRDY#_A22
FRAME#_A23
AD17_A24
AD19_A25
VS2
RESET#
SERR#_WAIT#
REQ#_RSVD_INPACK
C/BE3#_REG
AUDIO_BVD2
STSCHG_BVD1_STSCHG
AD28_Data 8
AD30_Data 9
AD31_Data 10
CD2
GND
J26
Signal Name
+12V
GND
GND
+5V
4 and 5 wire Tochconnector
PIN
1
2
3
4
5
6
7
8
68
PIN
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
1
PCMCIA connector J25
35
1
34
User Manual
J29
1
Signal Name
Upper Right (5-wire)
Lower Right (5-wire)
Sense (5-wire)
Upper Left (5-wire)
Lower Left (5-wire) and Top Side (4-wire)
Bottom Side (4-wire)
Left Side (4-wire)
Right Side (4-wire)
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
DMC touchcontroller interface (option) J30
PIN
1
2
3
4
Signal Name
XM
YM
XP
YP
Internal USB interfaces
PIN
1
2
3
4
5
6
7
8
Signal Name
+5V
Data0Data0+
GND
+5V
Data1Data1+
GND
J31/J32
PIN
1
2
3
4
5
6
7
8
ATX Power button
PIN
1
2
1
2
1
8
7
Signal Name
+5V
Data2Data2+
GND
+5V
Data3Data3+
GND
J36
1
Signal Name
+3V STANDBY
GND
Front USB
PIN
A1
A2
A3
A4
Signal Name
VCC
DataData+
Gnd
PIN
B1
B2
B3
B4
Signal Name
VCC
DataData+
Gnd
5.6 OPTIONS
5.6.1 Operating Panel
D1
S1
S1 is used to power on the system after standby. D1 indicates the status of
power on.
PIN
1
2
3
4
Signal Name
LEDLED+
GND
Powerbutton
D1 LED Status
D1
Green
Orange
Status
Power on
Standby
http://www.kontron.com
31
V Panel 104 / 121 / 150 / 170 / 190
User Manual
5.6.2 Fieldbus modules (optional)
5.6.2.1 Profibus module
5
1
9
PIN
1
2
3
4
5
6
7
8
9
6
female
Signal Name
NC
NC
RXD-P/TXD-M
ISODE
ISOLATET GND
ISOLLATED +5V
NC
RXD-M/TXD-M
NC
5.6.2.2 Canbus module
1
5
6
PIN
1
2
3
4
5
6
7
8
9
9
male
Signal Name
NC
CANL
ISOLATED GND
NC
NC
NC
CANH
NC
NC
5.6.2.3 DeviceNet module
1
PIN
1
2
3
4
5
32
Signal Name
GND
CANL
SHIELD
CANH
+24V
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
5.7 BLOCK DIAGRAM
The diagram displayed below shows the main internal function blocks of the
Panel.
PS/2 Mouse
J28
IRDA
J21
USB 0/1
J22 und J31
USB 2/3
J32
LAN
J22
CF
J17
PS/2
Keyboard
J28
HDD
J18
Watchdog**
U43
ETX-Modul
LVDS
J7 und J35
LPT1
J1
COM1
COM2
CRT
J1
Switchlogic
COM2
J2
ISA-Bus
NVSRAM**
Super I/O
PCI-Bus
SJA1000*
EC1*
COM3
COM4
COM3
J3
Switchlogic
COM1
J1
Touch
J29 und J30
COM4
J4
Floppy
J16
PCI-Riser
J24
Fieldbus
PB, CAN
DeviceNET
J15
2nd LAN**
J37
PCMCIA**
J25
External interface
Internal interface
* only SJA1000 or EC1 populated
** optional populated
fig. 5-1
http://www.kontron.com
33
V Panel 104 / 121 / 150 / 170 / 190
6.
User Manual
MAINTENANCE
The Panel is designed and produced according to DIN EN ISO 9000:2000.
One of the main development intentions was to minimice service requirements.
As a result, with exception changing CMOS-Ram battery and cleaning, no great
service is to do.
In case off any error kindly note the remarks below.
To analyze the error please check first all connections and configuration of the
software. Don’t try to repair the hardware inside.
No warranty if improper operated
6.1 CUSTOMER SERVICE
To get more technical information and help concerning errors on the Panel please
contact Kontron customer service.
Tel:
+49 (0)9461 950 104
Fax:
+49 (0)9461 950 200
E-Mail:
support@kontron.com
Internet:
http://www.kontron.com
6.2 CLEANING
To clean the surface of the Panel use a soft lint-free cloth. It should be slightly
moist with a mild detergent solution or any computer cleaning kit.
Never use alcohol, petroleum-based solvents or aggressive agents to clean
the Panel. Also never poor any liquids directly in the Panel PC Box.
To clean the liquid-crystal display (LCD) screen use soft clean lintfree cloth,
moist with a mild glass cleaner, and gently wipe the surface. Never apply liquids
directly on the screen surface. Do not use paper towels to clean the display
screen. Paper can scratch the display touch film.
6.3 RETURN AND REPAIR
Kontron Embedded Computers GmbH has started a service management system according DIN EN ISO 9001:2000 to reduce the terms of repair. This provides a fast, high quality and effective repair.
34
© Copyright Kontron Embedded Computers GmbH
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: +49 9461 950 - 0
Fax: +49 9461 950 - 100
6.3.1 Return Material Authorization Numbers (RMA)
Before send back the defective device please follow the hints below then request a RMA number from Kontron customer service.
• Return only Kontron product specified on the RMA request.
• Request a separate new RMA number for each Kontron product.
• If we receive a shipment containing not authorized products, we may
send it back.
• Please check before requesting an RMA number if there is a real defect
on the system. If not we could charge the costs for handling.
To request a RMA number fill out the form „Fault report“ and send him to
Kontron customer support. You can get the form as a download on http://
www.kontron.com. For additional questions please contact the customer service
by fax or Email.
Fill out all the menu items on the form and send it to Kontron by FAX or online.
Describe the error as detailed as possible. A detailed report is a base for a fast
and effective analyze of errors and repair.
After getting back the “Fault report” send the defective device, including the
fault report and your delivery note, to the following address:
Kontron Embedded Computers GmbH
Warenannahme Service
Werner-von-Siemens-Str. 1
D-93426 Roding
6.4 PACKAGING
To return a system use the original Kontron or equivalent packaging. Parts or
components of the system must be returned in anti-static-bags.
Always enclose a copy of the original delivery note and the fault report.
Kontron is not responsible for damage during shipment. We recommend that
you insure the shipment.
http://www.kontron.com
35
V Panel 104 / 121 / 150 / 170 / 190
7.
User Manual
TROUBLESHOOTING
7.1 FAQ
Please look to the online support at www.kontron.com
8.
DISPOSAL
In order to dispose your Panel, it must be removed from the plant and fully
dismantled. Electronic part such as disc drives and circuit boards must be disposed of in accordance with national electronic scrap regulations.
For details ask your local waste disposal department.
9. APPENDIX
ILLUSTRATION CONTENTS
Fig. 3-1
Connect external devices .......................................................... 9
Fig. 3-2
Connect internal devices ......................................................... 11
Fig. 5-1
Block diagram .......................................................................... 33
36
© Copyright Kontron Embedded Computers GmbH
Download PDF