Samsung | SNP-1000A | User`s manual | Samsung SNP-1000A User`s manual

Real-time Network
Dynamic 10X
Pan & Tilt
10X PTZ Network Camera SNP-1000 User’s Manual
5IBOLZPVGPSQVSDIBTJOHB4".46/(J10-J4/FUXPSL$BNFSB
#FGPSFBUUFNQUJOHUPDPOOFDUPSPQFSBUFUIJTQSPEVDU
QMFBTFSFBEUIFTFJOTUSVDUJPOTDBSFGVMMZBOETBWFUIJTNBOVBMGPSGVUVSFVTF
ENGLISH
Preface
A brand that is integrated into Samsung's network products,
stands for a convenient world (Polis) made safe
(Police) through Samsung's superior network performance(Internet
protocol).
With
products'
clear
digital
images
transmitted over the internet, real-time monitoring is possible
anywhere with an internet connection. Easy remote control
functions and the use of existing networks minimize installation
costs. With
, experience a world of convenience
connected anytime, anywhere.
Preface
Thanks for purchasing of 10X PTZ Network Camera SNP-1000.
This is a user instruction manual for a 10X PTZ Network Camera
SNP-1000 that employs Samsung Techwin’s WINNER Ⅲ DSP
system with superior low light capability.
The user who installs and operates the product shall be aware of this
manual and other manuals referenced by this manual before the
installation and operation and use properly.
This manual and the software and hardware explained here are
protected by copyright law.
So the copy, reprint and translation to other languages of a part of or
all
contents
of
this
user
manual
without
permission
of
SamsungTechwin Co., LTD are not allowed except for the copy for
general use within the scope of copyright law.
i
Contents
Contents
Preface .............................................................................. i
Contents ...........................................................................1
Note to User .....................................................................5
Product Warranty and Limitations ....................................7
Warning Symbols .............................................................8
Danger..............................................................................8
Caution ...........................................................................10
Ch1. Overview .......................................................................12
1.1. 10X PTZ Network Camera SNP-1000 Introduction.........13
1.2. Features ..................................................................13
Ch2. Section names and functions .....................................16
2.1. Body ........................................................................17
2.2. Rear panel ...............................................................17
2.3. Connection to external terminal...............................18
Ch3. Installation and Network Setup...................................20
3.1. Components and Accessories.................................21
3.2. Installation ...............................................................22
3.2.1. Preparation for Cable ............................................. 22
3.2.2. Cable Connection................................................... 23
3.2.3. Installation of SNP-1000......................................... 25
3.2.4. Installing the SNP-1000 on a Ceiling ...................... 26
3.2.5. Installing the SNP-1000 Wall Mount ....................... 28
3.2.6. Installing the Dome Housing (STH-1000PI)............ 30
1
10X PTZ Network Camera SNP-1000
3.3. Network configuration and connection method .......31
3.3.1. Configuration/connection using Web page ............. 31
Ch4. How to Use Web Viewer...............................................36
4.1. How to Use Web Viewer..........................................37
4.1.1. Login ...................................................................... 37
4.1.2. Web Viewer screen ................................................ 38
4.2. Using Administration page.......................................44
4.2.1. Initialization Screen after Connecting ..................... 44
4.2.2. Live ........................................................................ 45
4.2.3. Basic ...................................................................... 46
4.2.4. Network.................................................................. 48
4.2.5. User ....................................................................... 49
4.2.6. Pan/Tilt/Zoom......................................................... 52
4.2.7. Motion Detection .................................................... 54
4.2.8. Alarm/Sensor ......................................................... 55
4.2.9. Time ....................................................................... 58
4.2.10. LOG ..................................................................... 59
4.2.11. Upgrade ............................................................... 60
4.2.12. System Reboot..................................................... 61
Ch5. How to Operate Camera...............................................62
5.1. OSD Menu Organization .........................................63
5.2. PTZ Camera User Menu Settings ...........................66
5.2.1. Camera Setting ...................................................... 66
5.2.2. FOCUS .................................................................. 66
5.2.3. White Balance ........................................................ 68
5.2.4. Exposure................................................................ 70
2
Contents
5.2.5. Back Light .............................................................. 71
5.2.6. AGC ....................................................................... 72
5.2.7. SSNR (Samsung Super Noise Reduction) ............. 72
5.2.8. Day & Night............................................................ 73
5.2.9. Others .................................................................... 74
5.3. Sequence Setting ....................................................75
5.3.1 Preset ..................................................................... 75
5.3.2. Swing SEQ............................................................. 77
5.3.3. Group SEQ ............................................................ 78
5.3.4. Tour SEQ ............................................................... 78
5.3.5. PTZ Trace .............................................................. 79
5.3.6. Auto Run ................................................................ 80
5.3.7. Power On Resume................................................. 81
5.4. P/T Setting...............................................................82
5.4.1. Pan Limit ................................................................ 82
5.4.2. Tilt Limit.................................................................. 82
5.4.3. Area Setting ........................................................... 83
5.4.4. Area Masking ......................................................... 84
5.4.5. Prop. P/T................................................................ 84
5.4.6. Digital Flip .............................................................. 85
5.4.7. Jog Speed .............................................................. 85
5.5. OSD Setting ............................................................86
5.5.1. Camera Name........................................................ 86
5.5.2. Preset Number ....................................................... 87
5.5.3. Preset Name .......................................................... 87
5.5.4. Sequence Status .................................................... 88
5.5.5. Area Name ............................................................. 88
3
10X PTZ Network Camera SNP-1000
5.5.6. PTZ Position .......................................................... 89
5.5.7. Language ............................................................... 89
5.6. Initialization Setting .................................................90
5.7. Status.......................................................................91
Ch6. Troubleshooting ...........................................................92
Appendix A. DDNS Usage.....................................................96
Specifications ...............................................................104
Dimension ....................................................................107
If you refer to the enclosed Quick guide and the
Note
Manual in the CD, you can learn how to use Network
Manager Standard.
4
Note to User
Note to User
This machine’s electromagnetic waves have been registered as
suitable for business purposes; the retailer and consumer should be
aware of this registration. If in the case of wrongful purchases,
please exchange the product for a home use product.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other
European countries with separate collection
systems)
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate this
from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources. Household users should
contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can
take this item for environmentally safe recycling. Business users
should contact their supplier and check the terms and conditions of
the purchase contract. This product should not be mixed with other
commercial wastes for disposal.
5
10X PTZ Network Camera SNP-1000
Samsung Techwin cares for the environment at all
product manufacturing stages to preserve the
environment, and is taking a number of steps to
provide customers with more environment-friendly
products.The Eco mark represents Samsung
Techwin s will to create environment-friendly
products, and indicates that the product satisfies
the EU RoHS Directive.
6
Product Warranty and Limitations
Product Warranty and Limitations
The manufacturers of this product do not take any responsibility for
this product; therefore, the manufacturer does not authorize the
third-party, but allows that retailer is responsible.
The product warranty does not extend to cover accidents, negligence,
abuse, or wrongful use for the whole or any part of the product.
Additionally, the manufacturer does not provide warranty for any
additional parts or affiliations.
The warranty is for one year from the purchase date. During the
period, warranty does not extend to malfunction in these areas.
y Malfunction due to user’s negligence
y Dismantlement or replacement by the user
y Connection to alternate power source
y Malfunction due to natural disasters (fire, flood, tsunami, etc.)
y Replacement due to wear and tear
y Instability of network
7
10X PTZ Network Camera SNP-1000
Warning Symbols
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for
future use.
Danger :
Misuse or wrongful operation of the product may
result in death, injury or bring about other fatal
results. It indicates absolute caution when operating.
Caution :
Misuse or wrongful operation of the product may
result in slight injury or damage to the product. It
indicates caution when operating.
Note :
Indication that the user needs to be aware of certain
matters, or will find matters helpful in operating the
product.
Danger
Before Setup
y Please set up the proper voltage before connecting to power
source.
y Please be sure the power is turned off before setup.
8
Danger
y There is risk of shock or fire; be sure to avoid setup in places
with high humidity.
y To prevent shocks, please connect the ground wire.
y Do not install the camera on a surface that can not support it.
y Unless the surface is suitable, it could cause falling or other
hazards.
During Use
y When opening the product cover, there is a risk of electric
shock. Only a professional should open the cover.
y Please use only in an environment with standard temperature
and humidity.
y Please do not plug in multiple products to a power source; it is
often the cause of fires.
y Please do not place water or heavy objects on the product; it is
often a cause of malfunction.
y Please do not use in a location with propane gas, gasoline or
other flammable substances to avoid risk of explosion or fire.
y Please do not touch the power plug with wet hands to avoid
electric shock.
y Do not pull on the power plug with too much force; a damaged
plug may cause electric shock or fires.
y Don’t connect the RJ-45 cable to a terminal by constraint.
y Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a
long time, Fire may be caused.
9
10X PTZ Network Camera SNP-1000
y Random replacement of built-in battery by other types of
batteries may cause explosion. The battery shall be replaced by
the same battery. The used batteries shall be disposed carefully
because they can cause environment pollutions.
y The battery shall be replaced by the same battery.
y The used batteries shall be disposed carefully because they can
cause environment pollutions.
Disassembly and Cleaning
y There is a risk of malfunction, shock or other dangers. Please
do not disassemble or attempt to fix the product.
y To prevent malfunction or shock, please do not use a wet cloth
or oil-based cleaning product to clean the product exterior.
Clean the exterior of the product with a dry cloth.
Caution
y Do not install under extreme temperature conditions
Use only under temperature conditions between -0°C and
+40°C. Provide good ventilation when using in high
temperature conditions.
10
Caution
y Do not install under unstable lighting conditions.
Severe lighting changes or flickering may hinder normal
camera operation.
y Do not drop the camera or subject it to physical shock.
May cause a product malfunction.
y Never keep the camera face to strong light directly.
May damage the CCD.
y Avoid touching the camera lens.
The lens is the most important component of the camera. Be
careful not to smear it with fingerprints.
y Do not expose the camera to rain or other types of liquids
Wipe dry any liquids. Liquids may contain minerals that are
corrosive to Electronic components.
y Do not expose the camera to radioactivity.
Radioactivity exposure may damage the CCD.
y Do not disassemble the camera.
If you disassemble the product as you please, a Repair Center
doesn’t repair it for free.
y Please check the created network place first, before trying to
connect to a network.
y Please use only the power adapter that is provided with the
product.
y Please check national laws to be sure that using the product for
monitoring purposes is not illegal.
11
C h 1.
Overview
1.1. 10X PTZ Network Camera SNP-1000 Introduction
1.1. 10X PTZ Network Camera SNP-1000 Introduction
The SNP-1000 is a high-tech network camera that uses MPEG-4
codec technology to allow high compression rates and clear picture
quality by allowing for high frame rates to be transmitted through
the network.
By using the network, remote connection, monitoring, and control is
possible from any location for simple use; additionally, set-up
requires only a network.
The 10X PTZ Network Camera SNP-1000 utilizes embedded
software solutions (Embedded Web Server, Embedded Streaming
Server, Network Protocol) developed by SamsungTechwin, and
guarantees performance and safety while offering various solutions
through Internet integration.
1.2. Features
€ 10X Zoom Lens with Auto-Focus Function
The 10X zoom lens having Auto-focus function magnifies
the image up to 100 times when used with the digital 10X
zoom function.
€ Variable Auto Surveillances
•
Individual Preset Saving Modes
12 camera adjustment functions can be saved independently
in each Preset menu to provide optimum images.
•
PTZ Trace
4 patterns which are set up by users can be saved and replayed.
13
10X PTZ Network Camera SNP-1000
•
Auto Swing
Pan or Tilt is operated in sequence between 2designated
positions.
•
Group Search
•
Tour Search
Maximum 128 Preset positions are toured in order.
Maximum 6 Group Search functions are toured in order.
€ Proportional P/T
Even when the Zoom-In function is On for the Pan and Tilt
speed correction function linked to the zoom position, fine
manual operation is possible.functions are toured in order.
€ Day & Night
Day & Night function of ICR (IR Cut-Filter Removal) and
Sens-Up function can achieve optimum images during
day and night.
※ Sens-Up function improves the CCD sensitivity by lengthening
the exposure time using electricity.
※ Day&Night function enables users to select and adjust the colour
and black and white images according to the light level.ions are
toured in order.
€ OSD (On Screen Display)
Items such as Camera ID, Camera Name, Preset Number,
Preset Name, Area Name and Camera Status are
displayed on the monitor. Camera functions can be set up
on the OSD menu screen.
14
1.2. Features
€ 128 Preset Position
A maximum of 128 Preset positions can be set up. This
function enables users to set up the monitoring place any
time.
€ Digital Flip
When you want to monitor the moving object below the
camera, you can execute the Digital Flip. The moving
object can be monitored without screen reverse.
€ Area Masking
For privacy protection, a maximum of 4 areas can be
masked among the surveillance areas preventing them to
be displayed on the screen.
€ High Data Compression Ratio
Its data transfer speed is very fast with high data
compression ratio based on MPEG-4 and it transfers
relatively high frame number at the same network
bandwidth.
15
C h 2.
Section names and functions
2.1. Body
2.1. Body
2.2. Rear panel
①
②
③
④
⑤
Power Connector
Audio Input Connector
Audio Output Connector
Alarm Input/Output Connector
Network Connector
17
10X PTZ Network Camera SNP-1000
2.3. Connection to external terminal
18
Alarm Connection Terminal
PIN NO.
NAME
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
S1
S2
G
+V
NO
NC
CM
Purpose
Not Used.
Not Used.
Not Used.
Alarm Input 1
Alarm Input 2
GND
DC 12V
Alarm Output(NO)
Alarm Output(NC)
Alarm Output(COM)
19
C h 3.
Installation and Network Setup
3.1. Components and Accessories
3.1. Components and Accessories
„ Accessories
„ Products Sold Separately
The following products are provided separately.
y Accessory Housing
- Wall Type Mount : STB-280PW
- Wall Type Mount : STB-230PW
- Dome Housing : STH-1000PI
Note
ƒ See pages 25 for product images.
21
10X PTZ Network Camera SNP-1000
3.2. Installation
3.2.1. Preparation for Cable
To install and use the SNP-1000, the following cables should be
used.
y Power Adapter Cable
The cable connected to the power input terminal of SNP-1000
is shown below with a rated voltage of DC 12V 4A.
y Video Cable
The BNC cable shown below is connected to the video output
terminal and the monitor of SNP-1000.
22
3.2. Installation
y Lan Network Cable
The cable connected to the network device of SNP-1000 for
Network communication is shown below.
Note
ƒ Video cable and LAN network cable are not
provided in this product’s package.
ƒ BNC connection terminal can optionally be used to
connect when the Analog output is necessary.
3.2.2. Cable Connection
1.
First, connect one end of the BNC video cable connector to the
Video Output Terminal.
2.
Next, connect the other end of the connector to the Video Input
Terminal of the monitor.
23
10X PTZ Network Camera SNP-1000
3.
For the network connection of the SNP-1000, connect the LAN
Cable as the figure below shows.
4.
Then, connect the Power Adapter Cable. Use a driver (-) to
screw one part of the Power Adapter consisting of two lines to
the Power Input Terminal of the camera holder.
5.
Connect the Power Adapter’s plug to the Power Outlet.
24
3.2. Installation
3.2.3. Installation of SNP-1000
„ Precautions for Installation
ƒ Check that the installation location can safely bear four times the
weight of the camera and its installation fittings.
ƒ When fixing the ceiling installation bracket, use the supplied
installation template and fixing screws.
ƒ Take care not to drop the product during installation. Do not allow
anyone to stand below the installation area.
„ Optional Products for Installation
y Wall Mount (STB-280PW)
This housing is used to install
the camera on an indoor wall or
ceiling using an external
conduit.
y Wall Mount(STB-230PW)
This housing is used to install
the camera on an indoor wall.
y Dome Housing (STH-1000PI)
This housing is used to install the camera
in a location that is dusty, or a place
where extra protection for the camera is
required.
25
10X PTZ Network Camera SNP-1000
3.2.4. Installing the SNP-1000 on a Ceiling
1.
Prepare the accessories in the camera box (power adapter,
installation template, audio extension cable, 1 loose-proof screw,
3 installation bracket fixing screws, 2 installation brackets,
installation cover, installation CD) and a tool for making a hole
in the ceiling.
2.
Attach the installation template to
the ceiling where you want to
install the camera, make a hole of at
least 65mm in diameter, and 3 holes
for fixing screws according to the
marks on the template, and pull the
external incoming cables out of the
hole.
Precautions before Attaching the Installation
Template
Caution
ƒ Installation Location: Check that the function
and performance of the camera installed on
the ceiling will not be adversely affected by the
external environment, and that the ceiling can
adequately support the weight of the camera.
ƒ Installation Direction: Determine the main
direction of the camera in advance and attach
26
3.2. Installation
the template so that the front of the template is
in line with the camera direction.
ƒ Caution: Since there is a danger of the product
falling during installation, take care not to allow
anyone to stand below the installation area.
3.
Align the arrow on the ceiling
attachment installation bracket
with the front of the template,
fix the bracket by fastening the 3
screws through the holes, and
connect the external incoming
cables (video cable, network
cable and power cord) to the
camera.
4.
Assemble the camera, which
should already have been
attached to the product
installation bracket, to the
ceiling attachment installation
bracket, facing forwards, and fix
the camera with the supplied
fixing screw.
5.
To complete installation,
rotate the installation
cover along the groove of
the ceiling attachment
bracket, and fix it.
27
10X PTZ Network Camera SNP-1000
3.2.5. Installing the SNP-1000 Wall Mount
1.
Prepare the accessories in the camera box (power adapter, audio
extension cable, 2 installation brackets, 1 loose-proof screw,
installation CD, installation cover) and the wall mount(STB280PW or STB-230PW) and 3 installation bracket fixing
screws in the mount packaging box.
2.
Fix the wall mount (STB-280PW) with 3
screws to the wall where the camera is to be
installed, as shown in the figure on the right.
Precautions before Attaching the Installation
Template
Caution
ƒ Precautions before Attaching the Installation
Template
ƒ Installation Place: Check that the function and
performance of the camera installed on the
wall will not be adversely affected by the
external environment, and that the ceiling can
adequately support the weight of the camera.
ƒ Installation Direction: Determine the main
direction of the camera in advance and attach
28
3.2. Installation
the template so that the front of the template is
in line with the camera direction.
ƒ Caution: Since there is a danger of the product
falling during installation, take care not to allow
anyone to stand below the installation area.
3.
Fix the wall bracket and the wall surface attachment installation
bracket onto the wall mount (STB-280PW) with the screws
supplied, as shown in the figure on the right, and connect the
external incoming cables (video cable, network cable and
power cord) to the camera.
4.
Assemble the camera, which should already have been attached
to the product installation bracket, to the wall attachment
installation bracket, facing forwards, and fix the camera with
the supplied fixing screw.
29
10X PTZ Network Camera SNP-1000
5.
To complete installation, rotate the installation cover along the
groove of the ceiling attachment bracket, and fix it.
3.2.6. Installing the Dome Housing (STH-1000PI)
To install the Dome Housing (STH-1000PI), fix it instead of
installing the cover in the last step “3.2.4. Installing the SNP-1000
on a Ceiling” on page 26 and “3.2.5. Installing the SNP-1000 Wall
Mount” on page 28.
ƒ When the Dome Housing is
installed on the ceiling
30
ƒ When the Dome Housing is
installed on the wall
3.3. Network configuration and connection method
3.3. Network configuration and connection method
3.3.1. Configuration/connection using Web page
Use when there is one 10X PTZ Network Camera SNP-1000 to be
installed.
1.
Please connect user’s PC to 10X PTZ Network Camera SNP1000 using cross cable.
2.
To configure network, the internal IP must be registered in the
user’s PC.
31
10X PTZ Network Camera SNP-1000
3.
After pressing internet protocol (TCP/IP) properties, press the
‘advanced’ button to go into advanced configurations.
4.
The IP address of IP setting tap can be added as
"192.168.1.XXX"
"XXX" is an IP address voluntarily set by a customer.
5.
Please launch a Web browser on user’s PC and enter
[192.168.1.100] in the URL address field and push <Enter>
button. Connect to Webviewer login window of 10X PTZ
Network Camera SNP-1000.
6.
Please login with administrator’s authorization and move to
‘Setup-Network’ page.
32
3.3. Network configuration and connection method
Note
7.
Default value is ID : admin, PW : 11111111
Please configure according to the network environment where
10X PTZ Network Camera SNP-1000 will be installed and
push <Save> button to save the configuration.
33
10X PTZ Network Camera SNP-1000
① LAN / xDSL/ DHCP Configuration
Item
LAN Use
xDSL
Video Quality
Description
When network product is connected to normal
local LAN or when connected to static IP, the
network data to be allotted to the IP is configured.
When using xDSL dynamic IP, enter the ID and
PW.
When automatically receiving IP through DHCP
server, the DHCP functions are activated.
‘DHCP’ is used in the LAN environment where the
DHCP is activated. Generally, for mid/large scale,
DHCP servers are operated through LAN and for
small-scales, IP sharers use DHCP functions.
② Port Configuration
Item
Port Setting
34
Description
The connection port and http, ftp port
configurations can be set here and the DDNS use
can be checked.
3.3. Network configuration and connection method
Note
Use DDNS changes its IP address every time the
user attempts to connect to the ISP and when the
product is connected to a cable modem or xDSL
modem. In this case, the user cannot know the
changed IP address. When a product that uses
dynamic IP is registered on the DDNS server, when
wishing to connect to the product, the changed IP
address can be easily recognized. In order to register
the IP address to the DDNS server, set Use DDNS as
Enabled.
35
C h 4.
How to Use Web Viewer
4.1. How to Use Web Viewer
4.1. How to Use Web Viewer
4.1.1. Login
To connect to the login page, click the ‘move to Webpage’ button on
Network Manager or enter network camera IP address on the
internet web browser and press the enter key.
Enter user ID and password and push <Login> button, it then moves
to the appropriate Web page.
Note
Default value is ID: admin, PW: 11111111
If you click <Guest> button, it moves to WebViewer page under the
Guest authenticated status. However, administrator has to permit
guest access for this.
Note
If you logged in first in administrator mode, please
change the password of administrator. It can
prevent other users from connecting to the
administration page.
37
10X PTZ Network Camera SNP-1000
4.1.2. Web Viewer screen
Web Viewer screen is composed of menu area for camera/video
configuration and screen area for displaying input video from
camera.
„ Controls
Flip Image
Vertical reversal of channel screen
38
4.1. How to Use Web Viewer
Stretch Image
When selecting resolution with Half D1 and CIF, stretches
channel screen to resolution D1 size.
Save Image
Saves channel screen to ‘JPEG file’.
Quad
Converts to 4 split screens (applied only to 4 channel server).
Compression
Video compression mode (the mode of
compressing video)
- MPEG, JPEG
Resolution
Video resolution (the size of video screen
transmitted)
- NTSC : D1(704x480), Half D1(704x240),
CIF(352x240)
- PAL : D1(704x576), Half D1(704x288),
CIF(352x288)
Frame Rate
The number of maximum video frame
transmitted for each second.
- 1, 5, 10, 15, 20, 25, 30
Quality
Quality Configures video quality
- Very High, High, Normal, Low, Very Low
39
10X PTZ Network Camera SNP-1000
Pause
Stops video for a while.
OSD
Displays related information.
Displays the title
Removes the title
40
4.1. How to Use Web Viewer
Deinterlace
On/off function of Deinterlace.
Screen where
Deinterlace is not
applied
Screen where
Deinterlace is not
applied
Deinterlace is a function to adjust the video quality
Note
softly by eliminating the border line which was made
by an interlace function. The interlace function draws
an even line and an odd line of the Image one after
the other.
41
10X PTZ Network Camera SNP-1000
Camera Setup
Displays OSD control button of camera.
Camera OSD
control button is
displayed
Camera OSD is
displayed
Day&Night
Day&Night configuration function
(Color, B/W configuration)
PTZ Control
PTZ control function
Screen where
camera PTZ
control window is
displayed
42
4.1. How to Use Web Viewer
Note
ƒ The left/right slide bar can control focus (left slide
bar) / zoom (right slide bar)
ƒ The “+” displayed in the middle can be pressed
using the mouse as the base point of the Pan / Tilt
and it will Pan /Tilt according to that point.
Instruction for Camera OSD control button
<↑>, <↓> button
Moves selection displaying arrows up and down on
camera OSD menu.
<←>, <→> button
Changes configuration of selected field on camera OSD
menu.
<Set> button
Displays camera OSD or moves to upper/lower menu of
selected field.
<Exit> button
Terminates camera OSD.
※ For configuring the function and detail operating method of 10X
PTZ Network Camera SNP-1000, refer ‘Ch5. How to Operate
Camera’.
43
10X PTZ Network Camera SNP-1000
4.2. Using Administration page
4.2.1. Initialization Screen after Connecting
When connection is successful, the below screen will be displayed.
44
4.2. Using Administration page
4.2.2. Live
Please Move to Web Viewer page
[Web Viewer live screen]
45
10X PTZ Network Camera SNP-1000
4.2.3. Basic
Configures basic information for camera.
Video/Audio Setup
Item
Description
Compression
Video compression mode
(Compression mode of video in the camera)
Video Size
If the type of installed camera (NTSC/PAL) is
selected, then the size of screen on the
camera becomes selectable.
Video Quality
Selects the quality of video screen. In case of
low speed internet, lower the video quality to
see seamless video.
Video FrameRate
Configures the number of transmitted frame
per second in the camera.
46
4.2. Using Administration page
Item
Description
Selects the video channel to be used in the
camera.
Video Channel
Selects whether to use the audio input
channel in the camera or not.
Selects whether to use the audio output in the
camera or not.
Configures the number of users who can be
connected to the camera through the
network(1~20 persons)
Audio amplifying function
onfigures Low for the microphone which has
amplifying function and High for the
microphone which has no amplifying function.
(In case of Line-In signal, configure Low)
Audio-In Channel
Audio-Out Channel
Max User Count
Mic. Sensitivity
Product Information
Item
Description
Model
Mac Address
Displays model name of the camera.
Displays MAC Address of the camera.
Camera Name
onfigures name of the camera, it help to classify
several cameras.
Location
Description
Memo
The location of the installed camera can be
entered.
Additional description related to the camera can be
entered.
The contact of camera administrator can be
entered.
47
10X PTZ Network Camera SNP-1000
4.2.4. Network
Configures network information of the camera.
Network Configuration
According to the user’s network environment, it is classified into
LAN, xDSL, DHCP.
Item
LAN
xDSL
DHCP
48
Description
In case the camera is connected to the local
network or xDSL with a static IP address, configure
network information to be assigned to the camera.
In case of xDSL with a dynamic IP address, enter
password in UserName and Password field.
This case is selected in case of using IP sharing
box/ cable modem.
4.2. Using Administration page
Port/DDNS Configuration
Item
Connection
Port
HTTP Port/
FTP Port
Use SWR
Use DDNS
Description
This controls communication with camera.
(Default : 4000)
This helps to connect to web page or FTP server.
(Default : http=80, ftp=21)
Select if use of SWR function is available. The way
of connection which used ID does not support.
Select if DDNS server is available. DDNS server is
connected to server without reference to changed
IP because there is possibility that floating IP
constantly is changed.
※ A detailed explanation about DDNS usage refers to <Appendix A.
DDNS Usage>.
4.2.5. User
This describes password change for administrator or user
registration.
49
10X PTZ Network Camera SNP-1000
Item
Description
Administrator
Password Change
Change password of administrator
Guest Setup
User clicks ‘Guest’ button to decide whether
allowing guest to connect Main Viewer.
Current User
You can register new user or delete, and set up
user’s authority.
※ Set up user authority
User’s authorities set up at ‘Current User’ are as follows.
Item
Video
Control
Description
Use video related setup function
(Compression, Resolution, Framerate, Quality)
Pan, Tilt, Zoom, Audio output, Alarm output
Audio
Audio Input
USE
Whether relevant account is used
(If not checked, not allowed log-in)
50
4.2. Using Administration page
ƒ Example 1) In case control function is limited (Do not check
Controls box)
※ Pan, tilt, zoom, audio output, alarm output function icon is
inactivated
ƒ Example 2) In case video function is limited (Do not check Video)
※ Compression, Resolution, Framerate, Quality set up icon is
inactivated.
51
10X PTZ Network Camera SNP-1000
4.2.6. Pan/Tilt/Zoom
Configures PTZ Swing and Preset of the camera.
52
4.2. Using Administration page
Item
Channel
PTZ Display
OSD Display
PTZ
Camera
Configura
tion
Preset
Swing
Group
First Setup
Swing
Setup
Group
Setup
Second Setup
Mode
Speed
Duration
Group No.
Preset No.
Travel Speed
Dwell Time
Description
Select the channel of camera.
Display PTZ menu.
Display OSD.
Set or delete(delete, delete all) the
Preset. Screen move the position of
Preset.
Surveille Pan/Tilt Swing at the position
of preset, set up the swing menu.
Surveille repeatedly at the position of
preset, set up the Group menu.
Indicate the first position of surveillant
Preset
Indicate the second position of
surveillant Preset
Select Pan/Tilt Mode.
Set Swing speed between Presets.
Set interval time on Preset.
Set Group Number among 1~6
Set Preset included the Group.
Set swing Speed between preset.
Set interval time on Preset.
53
10X PTZ Network Camera SNP-1000
4.2.7. Motion Detection
This sets up motion detection function of camera.
Item
Grid Display
Select Area
MD Enable
MD Sensitivity
54
Description
Basic grid, used to choose area on the screen, is
displayed or hidden.
When selecting motion detection area, click <Select
All> button to select all areas, or click <Deselect>
button to cancel the selected area.
Decide whether you use motion detection function.
Setting up sensitivity to detect motion to adjust input
video by situation. You can select 1-5, and 5 is the
highest.
4.2. Using Administration page
4.2.8. Alarm/Sensor
This sets up necessary information when using alarm function by
attaching sensor to camera.
55
10X PTZ Network Camera SNP-1000
Alarm/Sensor Setup
◊ Digital In Setup
Item
Description
Sensor Type
Types of sensors are ‘Normal open’ and ‘Normal
close.’ This selects up type of connected sensor.
◊ Digital Out Setup
Item
Description
Set up Alarm Out responding when event is
recognized by connected sensor (Sensor 1) or
Motion Detection (MD)
Set up time to operate relay. It means the period
from the time when sensor detects event to the
time when relay is released.
In case event occurs by sensor (Sensor 1) or
Motion Detection (MD) on the screen, decide
whether transferring related information to FTP.
Alarm
Duration
FTP
In case event occurs by sensor (Sensor 1) or
Motion Detection (MD) on the screen, decide
whether transferring related information by e-mail.
E-mail
E-mail/FTP Setup
Set up FTP server and e-mail information to which related
information is transferred in case alarm occurs.
Item
Mode
Server Name
FTP
Home Directory
User ID
User Password
56
Description
Select media for data transfer.
Enter domain or IP address of FTP
server.
Set up home directory to save relevant
data at FTP server.
Enter ID to connect FTP server.
Enter PW to connect FTP server.
4.2. Using Administration page
Item
Description
Recipient E-mail
Address 1
Recipient E-mail
Address 2
Server Name
E-mail
ID
Password
Mail Subject
Mail Body
Note
You can designate up to two e-mail
address receiving data when alarm
occurs.
In case you use outside e-mail server,
enter the name of the outside e-mail
server.
Enter ID to connect the outside e-mail
server.
Enter PW to connect the outside email server.
Enter the subject of mail to be
transferred.
Enter the body of mail to be
transferred.
If motion is detected, the contents transferred by email or to FTP are varied according to the set-up of
‘Video Compression’ at Admin page (Basic).
ƒ MPEG : Video length is set by ‘Duration’ of ‘Digital
Out Setup’.
File extension is ‘ste’, you can play this by ‘SLiM
Player’.
ƒ JPEG : JPG type image file attached.
57
10X PTZ Network Camera SNP-1000
4.2.9. Time
Current Time
Item
Date
Time
Description
Current setup date displayed
Current setup time displayed
Time Setup
Item
Set Manually
Time Server
58
Description
Adjust time manually.
Set up address of time server for Server 1 - 5.
4.2. Using Administration page
4.2.10. LOG
Recent activities made for camera are displayed as log.
Item
Lines
View
Clear
Description
Set up number of lines of the list.
Log is viewed with number of lines you set up most
recently.
Delete logs.
59
10X PTZ Network Camera SNP-1000
4.2.11. Upgrade
Upgrade program of 10X PTZ Network Camera SNP-1000.
System Upgrade Configuration.
Item
Firmware/Web
Description
Upgrade firmware and Web-page of 10X PTZ
Network Camera SNP-1000.
Factory Mode Setup
If you click <Reset> button, server is returned to initial value when
shipped from the factory after confirmation procedure by
administrator.
60
4.2. Using Administration page
4.2.12. System Reboot
System is rebooted after confirmation procedure of administrator.
Click <OK> button to reboot System.
61
C h 5.
How to Operate Camera
5.1. OSD Menu Organization
5.1. OSD Menu Organization
PTZ camera can be set up on the OSD (On Screen Display) menu
displayed on the video monitor.
① Camera Setting
P1
P2
P3
①Focus Mode
①Focus
②Zoom Tracking
➌Digital Zoom
➋White
Balance
AWB Mode
➊Brightness
➋Iris
③Exposure
➌Shutter
➍Sens-Up
➍Back Light
➎AGC
➏SSNR
➐Day
&
Night
⑧Others
High/Middle/Low/Off
High/Normal/Off
High/Middle/Low/Off
Auto
B/W
Color
➊Sync
➋Image Adj.
➌Freeze
P4
Auto/Manual/
One Shot AF
Mode: On/Off
Speed: Slow/Fast
Off(2X~10X)
ATW/AWC/MANUAL
►ATW
-ATW(I): Indoor
-ATW(O): Outdoor
►Manual
-Red
-Blue
25
Auto
Manual: Iris Level
--A.FLK
Manual:
1/60~1/120,000,
x2~x128
Auto: Sens-Up Limit
x1~x128
Off
Defaults
OneShot
AF
ON
Fast
OFF
ATW(O)
29
41
025
Auto
100
ESC
1/60
X4
OFF
Normal
Low
Burst Level
Sharpness
Color
On/Off
060
Internal
008
050
OFF
63
10X PTZ Network Camera SNP-1000
② Sequence Setting
P1
P2
①Preset
②Swing
SEQ
③Group
SEQ
④Tour SEQ
⑤PTZ
Trace
⑥Auto Run
⑦Power On
Resume
P3
P4
①Setting ②Edit ③Execute ④Clear ⑤Status
①Pan Swing
①Setting ②Execute ③Clear
②Tilt Swing
①Setting ②Execute ③Clear
①Setting ②Execute ③Clear
③P&T Swing
①Group1
①Setting ②Execute ③Clear
②Group2
①Setting ②Execute ③Clear
③Group3
①Setting ②Execute ③Clear
④Group4
①Setting ②Execute ③Clear
⑤Group5
①Setting ②Execute ③Clear
⑥Group6
①Setting ②Execute ③Clear
①Setting ②Execute ③Clear
①Trace1
①Replay ②Memorize
②Trace2
①Replay ②Memorize
③Trace3
①Replay ②Memorize
④Trace4
①Replay ②Memorize
➊Off
➋Preset: Preset No
③Swing: Swing Mode
Pan/Tilt/P&T
➍Group: Group No
①Mode
➎Tour
➏Trace: Trace1~Trace4
⑦A.Pan
- ①Auto Pan Speed: 20~50
- ②Tilt Angle: 10~45
➋Time
5,10,20,30(Sec), 1,2(Min)
On/Off
Defaults
OFF
32
25
30sec
OFF
③ P/T Setting
P1
P2
①Pan Limit
②Tilt Limit
③Area Setting
④Area
Masking
➎Prop.P/T
➏Digital Flip
⑦Jog Speed
64
P3
P4
①Area1
②Area2
③Area3
④Area4
①Mask1
②Mask2
③Mask3
④Mask4
ON/OFF
ON/OFF
Manual(10,20,30,40,50,60)
➊Area Name
➋Position
➌ON/OFF
➊Position ➋ON/OFF
➊Position ➋ON/OFF
Defaults
➊Position
➋ON/OFF
ON
ON
Manual
5.1. OSD Menu Organization
④ OSD Setting
P1
P2
①Camera Name
➋Preset Number
③Preset Name
➍Sequence Status
➎Area Name
➏PTZ Position
➐Language
P3
①ON/OFF ②Edit
ON/OFF
①ON/OFF ②Edit
ON/OFF
ON/OFF
ON/OFF
English, 中文,
Francais, Deutsch,
Espanol, Italiano
P4
➊Position
➋ON/OFF
Defaults
ON
ON
OFF
OFF
English
⑤ Initialize
P1
P2
P3
①Power On Reset
➋Initial Position
③Factory Default Set
④Camera Default Set
➎Auto Refresh
P4
➊Cancel ➋Execute
➊Position ➋ON/OFF
➊Cancel ➋Execute
➊Cancel ➋Execute
OFF, 1~7Days
Defaults
OFF
➏ Status
P1
P2
Note
P3
P4
Defaults
Preset setting is only possible within the OSD menu.
Symbol Description
Note
ƒ When there are sub menus under the selected
OSD menu.
Numbers are displayed in white color like ① on
the right top of the screen.
ƒ When there is no sub menu under the selected
OSD menu.
Numbers are displayed in black color like ➊ on
the right top of the screen.
65
10X PTZ Network Camera SNP-1000
5.2. PTZ Camera User Menu Settings
Execution of OSD Menu : After checking if the camera is in manual
operation mode, press the OSD Menu key. The following commands
are displayed on the monitor screen.
Main Menu
The selection key moves up and
down. Press the execution key
switch on the selected menu to
change the setup menu. Press the
ESC key to exit the OSD Menu.
5.2.1. Camera Setting
Select the Camera Setting on the Main Menu screen to control
camera settings
5.2.2. FOCUS
In Focus menu, you can set up the focus mode among Auto, Manual
or One Shot AF.
66
5.2. PTZ Camera User Menu Settings
➊Focus Mode
ƒ Auto : The camera adjusts the focus automatically while
monitoring the screen continuously in the auto mode. In the auto
focusing mode, zoom key operation is not recognized as the
input of the focus key.
ƒ Manual : In the manual mode, users can adjust the camera focus
manually.
ƒ One Shot AF : Only when the camera does not move, it turns into
the auto mode. It is the same as the manual mode.
②Zoom Tracking
ƒ Mode: When you select ON, the Focus function is executed when
the Zoom functionis on. When you select OFF, the Focus function
is not executed even when the Zoom function is on.
ƒ Speed: Fast will speed up the Zoom. Slow will slow down the
Zoom.
➌Digital Zoom
Magnification of the Digital Zoom can be selected among Off,
2X~10X.
※ It is recommended that the Digital Zoom should be set up before
the preset operation.
Caution
ƒ Digital Zoom
As the digital zoom magnification increases, the
image quality is lowered.
ƒ Auto-focus
Auto-focus may not function normally under the
following conditions.
- When the light level in the surveillance area
is low
- When the slow-shutter works
- When the amplification is increased
- When the light level in the surveillance area
is excessively high
67
10X PTZ Network Camera SNP-1000
- When the objects in the long and short
distance are under the same surveillance
area
- When there is no contrast (white and black)
in the object (e.g. sky or wall)
- When the thin horizontal line is captured
5.2.3. White Balance
The White Balance function corrects the abnormal white colour into
the normal white colour under any colour temperature lighting.
Select the mode among ATW, AWC and Manual. ATW is selected
by default.
„ WB Mode
ƒ ATW
Balances the colour automatically depending on the source of
light from 1,800~10,500K colour temperature.
- Indoor[ATW(I)] : Use this mode in the area under the limited
colour temperature.
- Outdoor[ATW(O)] : Use this mode in the area under the broad
colour temperature.
68
5.2. PTZ Camera User Menu Settings
ƒ AWC:
Set up the lighting to the objects and corrects the right colour
temperature to that of a white object. Camera works under the
setup conditions. For the most appropriate condition under the
current illumination, capture the white paper and then change the
mode into AWC. Press the Enter key and then AWC Start will be
displayed. When the adjustment is completed after pressing the
Enter key for AWC Start, go to the upper menu. When conditions
change, adjust the white balance function again.
ƒ Manual
Fine tuning is possible through this manual control mode. Select
the colour temperature and increase or decrease the Red or Blue
values to shift the colour of the object.
- Red : Red Gain can be changed.
- Blue : Blue Gain can be changed.
White Balance may not function properly under the
Note
following conditions.
ƒ When the colour temperature surrounding the
object is very high. (e.g. clear sky, sunset)
ƒ When it is dark around the object.
ƒ When the camera is pointing towards a fluorescent
lamp directly or when lighting conditions change a
lot.
69
10X PTZ Network Camera SNP-1000
5.2.4. Exposure
Camera exposure can be controlled.
➊Brightness
The brightness of the screen can be adjusted.
➋Iris
Auto mode or manual mode can be selected.
ƒ Auto: The brightness of the image signal can be adjusted
automatically depending on the amount of light.
ƒ Manual: The brightness of the image can be adjusted.
➌Shutter
ƒ ---: Electronic shutter mode is enabled. The shutter speed is
controlled automatically according to the brightness of the screen.
ƒ A.FLK: Use this mode when the screen flickers because of
inconsistent frequency with the surrounding lights.
ƒ Manual
- Shutter speed can be controlled manually.
- Shutter speed can be adjusted from 1/60(1/50) second to
1/120,000 second.
- Sens-Up function can be operated manually from x2 ~ x128.
Note
70
ƒ If the Shutter mode is ESC in the inner
synchronization mode and the camera faces to the
bright fluorescent lamp directly, the image may be
unstable. Be careful to select the installation
location.
5.2. PTZ Camera User Menu Settings
ƒ If the Manual or A.FLK mode is selected for the
Shutter menu, the Sens-Up function is disabled.
➍Sens-Up
ƒ Auto: The low light level of the night or dark condition is detected
automatically and the bright and clear image can be maintained.
- Sens-Up Limit: Maximum accumulated magnification can be
selected.
ƒ Off: Sens-Up function is cancelled.
Note
As the accumulated magnification increases, the
screen goes bright. But, the after image of the
moving object also becomes larger and the optimum
Auto Focus function may not work.
5.2.5. Back Light
Unlike other cameras, Samsung Techwin’s unique W-III DSP chip
gives you a clear image of the subject even with bright backlight.
ƒ HIGH : Gain increased from 6dB up to 34dB.
ƒ MIDDLE : Gain increased from 6dB up to 30dB.
ƒ LOW : Gain increased from 6dB up to 18dB
ƒ OFF : BLC function is cancelled.
71
10X PTZ Network Camera SNP-1000
5.2.6. AGC
When the brightness of the image taken under dark light is under a
certain level, the AGC (Automatic Gain Control) functions to define
whether to control the Gain automatically or not.
ƒ HIGH : Gain increased from 6dB up to 34dB.
ƒ NORMAL : Gain increased from 6dB up to 18dB.
ƒ OFF : Gain is fixed at 6dB.
5.2.7. SSNR (Samsung Super Noise Reduction)
SSNR function reduces background noise under low light conditions
differently in different modes. The noise reduction effect grows in
Off, Low, Middle and High modes in order.
ƒ OFF : No noise reduction effect.
ƒ LOW : Noise reduction effect is small but there is little afterimage.
ƒ MIDDLE: Noise reduction effect is generally effective in this mode.
Noise can be reduced properly and the afterimage is not strong.
72
5.2. PTZ Camera User Menu Settings
ƒ HIGH : Noise reduction effect is excellent but afterimage is also
strong.
When you select the AGC mode as “OFF”, you
Note
cannot use the SSNR function.
5.2.8. Day & Night
The darkness level is detected automatically under low light
conditions such as at night or under dark light to keep the screen
bright and clear.
ƒ COLOR : Output images are displayed in colour all the time.
Burst signal size can be adjusted.
ƒ B/W : Output images are displayed in black and white all the time.
Burst signal can be kept or removed.
73
10X PTZ Network Camera SNP-1000
ƒ AUTO : Under day condition, the mode is automatically changed
into the COLOR mode to keep an optimum colour. At night, the
mode is automatically changed into the B/W mode to distinguish
dark images clearly.
Note
ƒ If the AGC is in OFF mode, the Auto mode cannot
be used. Only COLOUR or B/W mode can be used.
ƒ If the sunlight or halogen lamp is used in B/W mode,
the focus may be blurred compared with the general
illumination.
5.2.9. Others
①Sync
Internal Sync is selected by default.
ƒ Internal : Internal synchronization
➋Image Adj.
Clarity of the video signal and saturation of the color may be
adjusted.
ƒ Sharpness : The overall sharpness of the image can be adjusted.
ƒ Color : The overall colour density of the image can be adjusted.
➌Freeze
Moving image can be stopped and replayed.
ƒ ON : Image can be frozen.
ƒ OFF : Frozen image is released and the film is replayed.
74
5.3. Sequence Setting
5.3. Sequence Setting
Sequence Setting Menu
5.3.1 Preset
12 items such as Pan/Tilt location, Zoom and Focus are selected
among camera functions and they can be called for monitoring.
Total 128 points can be preset.
ƒ Setting : Select the Preset number for setup. Adjust
Pan/Tilt/Zoom and press the Enter key to save the setting. If you
want to change the 12 items such as Focus, Brightness, Iris and
Scene Adj., use the Up/Down key to go to and select the item. If
you don’t want to change the 12 items, press the ESC key to go
to the next Preset step.
ƒ Edit : You can edit the 12 preset items such as Pan/Tilt location,
Zoom and Focus, which are selected among camera functions.
ƒ Execute : Select the Preset number for execution.
ƒ Clear : Select the Preset number to delete for clearing.
ƒ Status : The current Preset number setup is displayed.
75
10X PTZ Network Camera SNP-1000
„ Preset Menu Setting
1.
Select the Preset item on the Sequence Setting Menu
2.
Select the Setting item.
3.
Select the Preset number.
4.
Set up the Zoom and Focus.
5.
To change the camera settings, select Edit from the upper menu
first. Select the item to change, and then make the necessary
adjustments.
6.
If you select the Scene Adj. item, such items as Shutter, AGC,
SSNR, Sens-Up, White Balance can be set up differently in
every Preset item.
76
5.3. Sequence Setting
Note
In the White Balance setting of the individual Preset
Scene Adj., the AWC selection is not available.
5.3.2. Swing SEQ
Swing surveillance can be executed and set up and the data can be
deleted.
ƒ Pan Swing : Swing surveillance for the Pan direction is executed
and set up. Data is deleted.
ƒ Tilt Swing : Swing surveillance for the Tilt direction is executed
and set up. Data is deleted.
ƒ P&T Swing : Swing surveillance both for the Pan and the Tilt
directions are executed and set up simultaneously. Data is
deleted.
- Setting : The Preset Position for Swing function is selected by
clicking the mouse and confirmed with the Execution key. SPD
77
10X PTZ Network Camera SNP-1000
is the moving speed (01-64step). DWL is the stop time (00120sec). Press the Execution key in the location with selection
mark to finish the setting process.
- Execute : Swing surveillance is executed. Stop key designates
this function.
- Clear : Data in the Swing function is deleted.
5.3.3. Group SEQ
Group SEQ: Sequence surveillance can be executed and set up and
data can be deleted. Up to 6 groups can be registered.
ƒ Setting : Preset position for swing is selected by clicking the
mouse and confirmed with the Execution key. SPD is the moving
speed (01~64 step). DWL is the stop time (00~120sec). Press
the Execution key in the location with selection mark to finish the
setting process.
ƒ Execute : Swing surveillance can be executed. Stop key will stop
this function.
ƒ Clear : Swing data can be deleted.
5.3.4. Tour SEQ
Group surveillance can be executed and set up and data can be
deleted.
78
5.3. Sequence Setting
ƒ Setting : The registered Group Sequence is selected by clicking
the mouse and confirmed with the Execution key. If the selected
number is not registered, it cannot be input. Press the Execution
key in the location with selection mark to finish the setting
process.
ƒ Execute : Group surveillance is executed.
ƒ Clear : Group surveillance data are deleted.
5.3.5. PTZ Trace
Maximum 4 patterns of the manual operation paths (for Pan, Tilt,
Zoom and Focus) are memorized and replayed.
ƒ Replay : The manual operation paths are repeated and replayed.
Stop key will stop the replay.
Note
If the operation range is limited using ①Pan Limit
and ②Tilt Limit, please note that other operations
79
10X PTZ Network Camera SNP-1000
ƒ Memorize: Manual operations for minimum 120 seconds after
executing this function are memorized into the internal memory.
Nevertheless, the memorizing time becomes different depending
on the PTZ operation. OVER mark will finish this function.
Note
If the operation range is limited using ①Pan Limit
and ②Tilt Limit, only the operations within the limited
range are memorized.
Note
Press the OSD key to stop the internal memory to
continue saving.
5.3.6. Auto Run
If there is no controller operation by the user for a certain time, the
sequence operation designated by the user will be executed.
ƒ Mode:
- OFF : Auto Run will be cancelled.
- Preset : Auto Run in the corresponding Preset number
- Swing : Auto Run in the corresponding Swing mode
- Group : Auto Run in the corresponding Group number
- Tour : Auto Run in the corresponding Tour number
- Trace : Auto Run in the corresponding Trace number
- A. Pan : 350° Auto Run in Pan direction
※ Auto Pan Speed: Pan operation in the speed designated by
the user
※ Tilt Angle: The tilt angle set up by the user is kept.
80
5.3. Sequence Setting
ƒ Time : Auto Run operation is executed after a certain time
designated by the user.(Time can be set up by the unit of 5, 10,
20, 30 sec and 1~5 min.)
5.3.7. Power On Resume
When the power supply for the camera is stopped for some reason,
such as electricity failure, and resumed, the Sequence Settings
before the power off are restored.
81
10X PTZ Network Camera SNP-1000
5.4. P/T Setting
5.4.1. Pan Limit
The moving range in the Pan direction can be limited.
ƒ Position : Moving range can be set up. Set the position from the
left using the Execution key. The stop position may change due
to the initialization by such operation as power resumption
depending on position setting. This does not mean it is out of
order.
ƒ On/Off : When this function is on, the limit is effective. Default
setting is Off.
5.4.2. Tilt Limit
Moving range in the tilt direction can be limited.
ƒ Position : Moving range can be set up. Set the position from the
top direction using the Execution key. The stop position may
change due to initialization by such operation as power
82
5.4. P/T Setting
resumption depending on position setting. This does not mean it
is out of order.
ƒ On/Off : The application of limitation will be determined. Default
setting is Off.
5.4.3. Area Setting
Areas can be indicated. Areas can be designated up to 4.
ƒ Area Name : Area name can be set up. Use the Execution key to
enter the area name. A maximum of 12 letters (English, Chinese,
numbers) can be entered. When you finish inputting the name,
adjust the position mark to ”SET” and press the Execution key.
This is the end of Area Name setting.
ƒ Area Position : Area range can be designated. Use the Execution
key to determine the position from the left. If the area range is
overlapped, the smaller area number will indicate the overlapping
part.
ƒ On/Off : It can be determined whether or not to activate the area
mark. The activation becomes effective as soon as the position
moves from the current area to other areas. Set up the OSD
Setting as ON. If it is in OFF mode, this function does not work.
Default setting is OFF.
83
10X PTZ Network Camera SNP-1000
5.4.4. Area Masking
If you want to exclude some areas for surveillance, they can be
turned into black. You can mask 4 parts of one screen.
ƒ Position : Use the Execution key to determine the position for
screen operation from the left.
ƒ On/Off : Operation of screen area masking can be determined.
Default setting is OFF.
Note
If Area Masking is set while the Camera is in the
Digital Flip posion, automatically the Camera moves
the initial position which is not set for the Digital Flip
and then Area Masking position can be set. This is
not a malfunction.
5.4.5. Prop. P/T
Pan and Tilt speeds can be changed depending on zoom
magnification. Tele will slow down the speed of Pan/Tilt and Wide
will increase the Pan/Tilt speed. It will take about 20 seconds for 1
cycle in Tele mode and about 3 seconds in the Wide mode. Default
setting is ON.ed. Default setting is OFF.
84
5.4. P/T Setting
5.4.6. Digital Flip
When you operate the Tilt up to 100° limit and keep it for a certain
time, the image gets reversed automatically and the opposite Tilt
area is seen. When you want to monitor the moving object under the
camera, execute the Digital Flip function. You can observe the
moving object without reversing of the screen.
5.4.7. Jog Speed
Because using Pan/Tilt command protocol is fixed speed type ,so
that occation that Pan/Tilt speed is slow, can adjust command rate
by enter manual mode.
85
10X PTZ Network Camera SNP-1000
5.5. OSD Setting
5.5.1. Camera Name
Camera name is set up.
If you want to edit the item, move the cursor. Then
Note
select the character.
y Edit : A maximum of 12 characters consisting of English (or
Chinese, Japanese), numbers and special characters can be
input for Camera Name.
y On/Off : The operation of this function is preset. Default setting is
On.
86
5.5. OSD Setting
5.5.2. Preset Number
Preset numbering is set up. (Default setting is ON.)
5.5.3. Preset Name
ƒ Edit : A maximum of 12 characters consisting of English (or
Chinese), numbers and special characters can be input for
Preset Name.
87
10X PTZ Network Camera SNP-1000
ƒ On/Off : The operation of this function is predetermined. Default
setting is On.
5.5.4. Sequence Status
Display of the Sequence Group is set up. (Default setting is ON.)
5.5.5. Area Name
Display of Area Name is set up.
When the Area Name is OFF, the Area Name cannot be displayed.
88
5.5. OSD Setting
5.5.6. PTZ Position
Pan and Tilt position and Zoom magnification are displayed.
PTZ positions are not displayed in the OFF mode. (Only manual
operation can display them.)
5.5.7. Language
The OSD can be displayed either in English (default setting) ,
Chinese, French, German, Italy and Spanish.
89
10X PTZ Network Camera SNP-1000
5.6. Initialization Setting
Initialization Menu
①Power On Reset
Camera is initialized into the original status of power input.
➋Initial Position
If you want to set the default direction of the camera so that the
camera faces that direction when the power is turned on, you can set
up the desired Pan and Tilt for the camera.
③Factory Default Settings
Camera is initialized into the factory default settings.
Data including Preset is deleted. This function is used for
initialization all settings.
④Camera Default Settings
If only the camera module is replaced due to camera module failure,
the new camera module can be set up with the settings of the old
camera module.
➎ Auto Refresh
The electric circuit and the status of the equipment parts within the
camera are optimized regularly. (The cycle can be set up.) If camera
faces toward a certain source of light or if the settings cannot be
kept because of the long time rotation filming of a certain area, the
Auto Refresh function is used to maintain and reset the existing
90
5.7. Status
camera settings. Default setting is OFF.
ƒ OFF, 1-7 Days : This function is disabled in the OFF mode. 1-7
Days enables the Auto Refresh operation in the interval of the
selected days. Auto Refresh takes less than 10 seconds. The
message “Auto Refresh” disappears after finishing the operation.
5.7. Status
The status of PTZ camera setting is displayed.
CAM MODEL= 10NC
CAM VERSION= 4.6
DOME VERSION= 1.00
CON PROTOCOL=SAMSUNG TW
DOME ID= 001
CONTROLLER= Duplex-19200
Camera Model
Camera S/W Version
Control Board S/W Version
Protocol Setup
Dome Camera ID
Communication Mode Setup
91
C h 6.
Troubleshooting
Troubleshooting
If there are problems in operation, please refer to the items below. If
the problem persists, please contact the agent you purchased this
product from.
Problem
Nothing appears on the
screen.
Solution
ƒ Please check the power connection.
ƒ Please check the images
connecting the video signal line
after
ƒ Open MS-DOS window to check
whether 10X PTZ Network Camera
SNP-1000 is connected to network.
※ In case of ping 192.168.1.100,
replace it with IP address set up.
The video image is not
clear.
ƒ Please check if the lens is clean.
Please clean the lens with a clean
cloth or brush.
ƒ Please adjust the contrast feature of
the monitor.
ƒ Please make sure that the screen is
not exposed directly to a bright light.
Please move the camera if necessary.
The screen is dark.
ƒ Please adjust the contrast feature of
the monitor.
ƒ If you have an intermediate device, set
the 75Ω/Hi-z properly, and check the
terminals.
There is a problem with
the camera operation.
The camera surface is
too hot and black
stripes appear on the
screen.
ƒ Please check if an appropriate power
source to the camera complies with
the
manufacturer's
standard
requirement, or if the voltage keeps
changing.
93
10X PTZ Network Camera SNP-1000
Problem
The MOTION
DETECTION function is
not working.
Solution
ƒ Please check if 'MOTION
DETECTION' mode is turned on.
ƒ Please check if the MD LEVEL is too
low.
ƒ Please check the setting of the MD
AREA.
When camera cannot
be controlled for Pan/
Tilt/ Zoom
ƒ Inspect the cables(power or network)
connected to the device.
Colors are not quite
right.
ƒ Please check
setting.
The screen is
flickering.
ƒ Please check if the camera is facing
directly into sunlight or fluorescent
light.
DAYNIGHT(Auto) mode
is not working.
ƒ Please check if the AGC menu is set
to the OFF position.
SENS-UP function is
not working.
ƒ Please check if the AGC menu is set
to the OFF position.
ƒ Connect to Admin page to check
whether user control is selected.
the
'WHITE
BAL'
ƒ Please check if the SHUTTER menu
is set to MANUAL mode.
ƒ Please check the limit of SENS-UP
AUTO mode.
Audio is not working
ƒ Please check the audio is selected
from admin page.
ƒ Please check speaker volume from
the viewer.
ƒ In case input sound through
microphone at Viewer is not outputted
through Audio Out of camera, please
check whether Audio Out channel is
selected at admin page. Or check
whether microphone is available at
Viewer.
94
Troubleshooting
Problem
Solution
ƒ Please check audio driver is working
in user’s PC.
ƒ Please use the enclosed Audio
Extension Cable to install easily when
connecting the audio cable.
Video is stopped
ƒ Please check whether network cable
of 10X PTZ Network Camera SNP1000 is correctly connected
ƒ In case user uses hub or IP router,
check
whether
these
network
equipments are working properly.
ƒ Open MS-DOS window and check
whether 10X PTZ Network Camera
SNP-1000 is connected to network.
No image from web
viewer
ƒ Click ‘refresh (shortcut; F5) ’ button at
browser to recall the page
ƒ Check whether power of camera and
network cable is properly connected.
ƒ Check whether computer is connected
to network.
ƒ If you use hub or router, check
whether such equipments are properly
operated.
(Note: Open MS-DOS window and
enter network ID of camera at ping
192.168.1.100)
ƒ Connect to Admin page to check
whether video output is selected.
Image transferred to
FTP or by E-mail
cannot be viewed
ƒ Video may not be viewed since Divx
codec is not installed in user’s PC.
Divx codec can decode video
compressed with MPEG4. Download
and install the latest Divx codec, and
check video.
http://www.divx.com/divx/download
95
Appendix A. DDNS Usage
DDNS Usage
Registration process of DDNS is as following:
€ Step1) Complete the registration form in iPOLiS
website.
The website is ‘www.samsungipolis.com’.
Figure A-1. Website of iPOLiS
97
10X PTZ Network Camera SNP-1000
Figure A-2. Membership Registration: SIGNUP
Figure A-3. Membership Registration: Input your information.
98
DDNS Usage
€ Step2) Register the equipment after login.
Figure A-4. Login
Figure A-5. The list of registered equipment.
99
10X PTZ Network Camera SNP-1000
Figure A-6. The list of registered equipment.
Figure A-7. Product Registration.
(Confirm repetition certainly at domain registration.)
100
DDNS Usage
€ Step3) Configure DDNS information in the
equipment.
ƒ Click the part of Network Configuration in website of Network
Camera.
ƒ Click “USE DDNS” in order to do “Enable” and input the address
of DDNS Server.
(Default: www.samsungipolis.com )
ƒ Enter the ID and Password that is written when register product
is in iPOLiS website.
The Configuration of DDNS in SNP-1000 is Completed.
101
10X PTZ Network Camera SNP-1000
€ Step4) Confirm the connection status of
relevant product in product list of iPOLiS
website.
Figure A-8. The List of Product.
Be able to confirm the information of connected
equipment if click <check> button of ‘Product information’.
102
DDNS Usage
Figure A-9. Product information
Move to Login website of relevant product if click <view>
button of ‘ view’.
The buttons which are <Edit> and <Delete> of ‘product
management’ move to relevant page through input
password to item that fertilize or erase information of
registered equipment in List of product.
Only, ‘ID(Domain)’ of product should establishes again as
‘ID(Domain)’ after deleting because it can’t be fertilized.
Figure A-10. Edit/Delete
103
10X PTZ Network Camera SNP-1000
Specifications
Camera Part
Items
Imaging device
TV
Total Number of Pixels
Valid Pixel
Horizontal Scan
Frequency
Vertical Scan
Frequency
Synchronization
Image Output
S/N Ratio
Horizontal Resolution
Minimum Light for
Object
Electronic Shutter
Sens-Up
Day & Night
White Balance
Flickerless Adjustment
Iris
Gain Control
OSD Display
Outline Correction
Focal Length
Digital Zoom
Maximum Aperture
Rate
Coverage Angle
Proximity Distance
Horizontal Rotation
Angle
Horizontal Rotation
104
SNP-1000N
SNP-1000P
1/4” Color Vertical Double Density Interline CCD.
410,000pixel
NTSC
PAL
811(H) X 508(V)
795(H) X 596(V)
768(H) X 494(V)
752(H) X 582(V)
15.734kHz
15.625KHz
59.94Hz
50Hz
Internal Sync
1.0p-p/75Ω
Higher than 50dB (AGC OFF)
520 TV Lines (Color)/570 TV Lines(B/W)
0.7Lux(Color), 0.1Lux(B/W)/(@50IRE),
0.0007Lux (Day & Night is On.)/(@50IRE)
Auto/Manual
Auto/Manual
(1/60 - 1/120,000)
(1/50 - 1/120,000)
ON (x2 - x128 Fields) / OFF
ICR(Filter Switching) ON/OFF
ATW(Indoor/Outdoor Selection)/AWC/
Manual (1,800K - 10,500K)
Fixed Shutter Speed
Fixed Shutter Speed
(1/100)
(1/120)
Auto/Manual (Iris Level Adjustment Mode)
Low, Middle, High, Off
ON/OFF
Adjustable Level
F3.8mm(WIDE)~F38.0mm(TELE), 10X Optical Zoom
OFF, 2~10X Selection (Total 100X Zoom)
Wide Angle 1:1.6, Tele 1:2.8
Wide: 51.2°(H) X 39.3°(V) Tele: 5.58°(H) X 4.27°(V)
1.5m(Tele)
350°
Manual/Program
Specifications
Items
SNP-1000N
Horizontal Rotation
Speed
Horizontal Minimum
Moving Angle
Vertical Rotation Angle
Vertical Rotation
Vertical Rotation Speed
Vertical Minimum
Moving Angle
Preset Position
Area Masking
SNP-1000P
Manual: 0.5° ~ 70°/s(64 levels)
Preset: 0.5° ~ 140°/s(64 levels)
0.02°
-5°~ 185° (Digital Flip)
Manual/Program
Manual: 0.5° ~ 150°/s(64 levels)
Preset: 0.5° ~ 100°/s(64 levels)
0.02°
Alarm
Operating Temperature
Operating Humidity
Power, Voltage
Power Consumption
Dimension
Weight
Max 128 points
Max 4 locations
2 Alarm Inputs
1 Alarm Outputs
(Relay: NC/NO/COM, 0.5A 125VAC, 2A 30VDC Max)
0°C ~ 40°C
20% ~ 75%(Except for dew condensation)
DC 12V±10%
Operating 8.5Watts below
Ø110 X 134.8mm
Less than 0.85kg
- Wall Mount Bracket : STB-280PW
Option
- Wall Mount Bracket : STB-230PW
- Dome Housing : STH-1000PI
※ The product design and dimensions may change without
previous notice for improvement of performance.
Note
ƒ The copyright of this manual belongs to Samsung
Techwin Co. Ltd.
ƒ Parts or the whole of this manual cannot be
reproduced or transmitted by any electric,
mechanic or audio method without the authorized
written approval of Samsung Techwin.
ƒ The contents of this manual may be changed for
an improvement of functions.
105
10X PTZ Network Camera SNP-1000
Network Part
Items
Output Resolution
Output Video Format
Video Compression
Stage
Compression
transmission speed
Audio Format
Ethernet
Protocol
Dynamic IP
DDNS
Max. User
S/W
SNP-1000N
SNP-1000P
NTSC :
704 x 480(D1), 704 x 240(Half D1), 352 x 240(CIF)
PAL :
704 x 576(D1), 704 x 288(Half D1), 352 x 288(CIF)
MPEG4 / MJPEG Selectable
5 stages (Very Low, Low, Middle, High, Very High)
NTSC : MAX 30 frame/sec
PAL : MAX 25 frame/sec
Bi-directional audio, 8KHz ADPCM
10/100Mbps
HTTP, TCP/IP, FTP, SMTP, DHCP, DNS, DDNS, NTP,
PPPOE
Supports XDSL and DHCP
Supports DDNS
20 Users
Supply Network
Program
Manager
Standard
※ The product design and dimensions may change without
previous notice for improvement of performance.
106
Installation
Dimension
Dimension
107
SAMSUNG TECHWIN
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
145-3, Sangdaewon-dong, Jungwon-gu,
Seongnam-si, Gyeonggi-do, 462-120, Korea
Tel: +82-31-740-8151~8 Fax: +82-31-740-8145
www.samsungtechwin.com
www.samsungipolis.com
SAMSUNG OPTO-ELECTRONICS UK, LTD.
Samsung House, 1000 Hillswood Drive,
Hillswood Business Park Chertsey, Surrey KT16 OPS
Tel: +44-1932-45-5308 Fax: +44-1932-45-5325
P/NO : Z6806.0857.01B
Download PDF