Montigo | H36PVN | Owner`s manual | Montigo H36PVN Owner`s manual

H36PV Manual
Installation & Maintenance Manual
H36PVN Power Vent
Flush Face
Fireplace
H36PVN Shown
H36PVN Shown
DANGER
Read and understand this manual.
Improper installation, adjustment,
alteration, service or maintenance
can cause serious injury, property
damage or even death. For
assistance or additional information
consult a qualified installer, service
agency or the gas supplier.
WARNING
Do not store or use gasoline or any
other flammable vapors and liquids in
the vicinity of this or any other gas
burning appliance. A fire or explosion
my occur causing serious injury,
property damage or even death.
XW2006
XW2002
NOTICE
CAUTION
Glass doors on gas fireplaces are
extremely hot while the fireplace is
on and remain hot even after the
fireplace has been turned off. Safety
screens are available and can reduce
the risks of severe burns. Please
keep children away from the fireplace
at all times.
Installer: Leave this manual with the
appliance. Do not remove.
Consumer: Retain this manual for
maintenance and future reference. Do
not Discard.
XW2012
XW2004
NOTICE
Blank
IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do
not use any phone in your building.
Immediately call your gas supplier
from a neighbor's phone. Follow the gas
supplier's instructions.
If you cannot reach your gas supplier,
call the fire department.
Blank
Flammable materials
Toxic
Corrosive
Danger overhead crane
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
General Warning
Laser Radiation
Explosion risk
Biohazard
Oxidising
Hot surface
Danger of entrapment
Fork lift trucks
Danger of death
High voltage
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Slippery floor
Watch your step
Glass hazard
Danger of suffocation
Blank
General Warning
Irritant
Flammable materials
Irritant
®
Watch your step
Cutting
High temperatures
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Watch for
falling objects
Electricity
Danger for cutter
Strong magnetic field
Optical radiation
Non ionizing
radiation
Blank
Gas bottles
US
High temperatures
Danger overhead crane
Toxic
Slippery floor
Watch for
falling objects
Laser Radiation
Low temperature
C
Cutting
Corrosive
Explosion risk
Gas bottles
General Warning
Fork lift trucks
High voltage
Glass hazard
Danger of suffocation
Entrapment hazard
Battery hazard
Radiation
Hazardous to the
Environment
Danger of harming
your hands
Glass hazard
Danger of suffocation
Fork lift trucks
Hazardous to the
Environment
High voltage
Danger of harming
your hands
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Flammable materials
Low temperature
Explosion risk
Strong magnetic field
Toxic
Optical radiation
Corrosive
Non ionizing
radiation
Danger overhead crane
Radiation
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Gas bottles
Watch for
falling objects
Rotating parts
Rotating parts
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
radiation
Radiation
Hazardous to the
Environment
Danger of harming
your hands
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Danger of death
XW2014
XG0694
Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248
030711
H36PVN Power Vent Indoor Gas Fireplace
NOTICE
You must read and understand this
manual prior to installation, operation or
troubleshooting this appliance. Please
retain this owner’s manual for furure
reference and maintenance.
XW2010
Table of Contents
Safety Alert Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
3
Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Section A: Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . 4
Important Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before you start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pre-Installation Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Understanding Basic Operation . . . . . . . . . . . . . . . . . . . . . 4
Installation Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Section 1: Installation Overview and Product Dimensions . . . . . 5
The H36 PV Fireplace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Fireplace dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Section 2: Framing the Fireplace . . . . . . . . . . . . . . . . . . . . 6
Rough frame-in Dimensions. . . . . . . . . . . . . . . . . . . . . . . . 6
Fireplace Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Section 3: Finishing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing Non-combustible materials . . . . . . . . . . . . . . . . .
Installing Combustible Materials. . . . . . . . . . . . . . . . . . . . .
Combustible mantles and facings. . . . . . . . . . . . . . . . . . . .
Fireplace facing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mantles and surrounds. . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
8
8
8
Section 4: Installing the Power Vent. . . . . . . . . . . . . . . . . . 9
Installing the roof mounted power vent. . . . . . . . . . . . . . . . 9
Venting Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Vertical Vent. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multi-Elbow Vertical Vent. . . . . . . . . . . . . . . . . . . . . . . . .
Downward Vertical Vent. . . . . . . . . . . . . . . . . . . . . . . . . .
9
9
9
9
Venting Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation of the External roof mounted power vent.. . . . . .
Installing the external roof mounted power vent module. . . . . .
Installing a Wall Mounted Vertical Exterior Power Vent . . . .
10.
11
12
13
Venting Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multi-Elbow Installations . . . . . . . . . . . . . . . . . . . . . . . .
Downward Vertical Venting. . . . . . . . . . . . . . . . . . . . . .
Venting Components. . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation of the external wall mounted power vent . . . . . . .
Installing the external wall mounted power vent module. . . .
Installing In-Line Linear Power Vent. . . . . . . . . . . . . . .
13
13
13
14
15
16
17
Venting Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Typical Vertical Vent. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Page 2
Multi-Elbow Vertical Vent. . . . . . . . . . . . . . . . . . . . . . . . 17
Downward Vertical Vent. . . . . . . . . . . . . . . . . . . . . . . . . 17
Venting Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Section 5: Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installation Of Electrical Supply. . . . . . . . . . . . . . . . . . . . .
Installing The Remote Switch. . . . . . . . . . . . . . . . . . . . . .
HSI Wiring Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conduit & Wiring clearances . . . . . . . . . . . . . . . . . . . . . .
IPI Wiring Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
21
22
23
23
Section 6: Installing the Gas Line . . . . . . . . . . . . . . . . . . 24
Fuel Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Pressure requirements:. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Gas Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Section 7:Removing & Installing the Door . . . . . . . . . . . 25
Removing the doors:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Installing the Door:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Section 8: Installing the Logset . . . . . . . . . . . . . . . . . . 26-27
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
Section 9: Start-up Sequence . . . . . . . . . . . . . . . . . . . . . . 28
Honeywell Intermittent Pilot. . . . . . . . . . . . . . . . . . . . . . . . 28
For Your Safety - READ BEFORE LIGHTING . . . . . . . . . 29
Lighting Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
Section 10: Cleaning and Maintenance . . . . . . . . . . . . . . 30
Removing the log grate. . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Brick lining / Refractory . . . . . . . . . . . . . . .
Removing the standoffs. . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the firebox access Panel. . . . . . . . . . . . . . . . .
30
30
31
32
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
32
33
33
Appendix A
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Power Vent Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Vertical Power Vent Detail. . . . . . . . . . . . . . . . . . . . . . . . . 35
Horizontal Power Vent Detail. . . . . . . . . . . . . . . . . . . . . . . 35
Appendix B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Appendix C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
State of Massachusetts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Safety Alert Key
DANGER
WARNING
Indicates a hazardous situation which, if not
avoided, WILL result in death or serious
injury or property damage.
Indicates a hazardous situation which, if not
avoided, COULD result in death or serious
injury or property damage.
CAUTION
NOTICE
Indicates a hazardous situation which, if not
avoided, WILL result in minor or moderate
injury.
Address practices that are important, but
not related to personal injury
Introduction
Warranty and Installation Information: (See Appendix B)
INTRODUCTION
Congratulations on your purchase of a Montigo Fireplace.
With over 30 years of experience, Montigo is committed to
providing you with a gas fireplace that is not only a beautiful
addition to your space, but that is also designed and manufactured
to the highest safety, reliability and engineering standards.
We strongly encourage you to read and carefully follow
the instructions laid out in this Installation, Operation and
Maintenance Manual and retain it for your future reference.
Pay special attention to all cautions, warnings, and notices
throughout this manual intended to ensure your safety.
The Montigo warranty will be voided by, and Montigo disclaims
any responsibility for, the following actions:
►Modification of the fireplace and/or components including
Direct-Vent assembly or glass doors.
►Use of any component part not manufactured or approved
by Montigo in combination with this Montigo fireplace system.
►Installation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation
requirements for factory-built gas fireplaces. Installation & repairs
should be done by a qualified contractor.
Blank
This manual covers installation, operation and maintenance.
Lighting, operation and care of this fireplace can be easily
performed by the homeowner. All installation and service work
should be performed by a qualified or licensed installer, plumber
or gas fitter as certified by the state, province, region or governing
body where the fireplace is being installed.
Flammable materials
General Warning
Explosion risk
Toxic
XG0649 - 031511
Natural Gas Propane
55,000
---
Fork lift trucks
High v
Hot surface
Danger of entrapment
Danger o
warning
Laser Radiation
Biohazard
Oxidising
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Gas bottles
Watch for
falling objects
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
radiation
Radiation
Hazardous to the
Environment
Fireplace BTU/H Input
Model#
Danger overhead crane
Hot glass will cause
burns.
Do not touch
glass until unit is cooled.
Never allow children to
touch glass.
This installation, operation and maintenance manual is applicable
to the models described below. Refer to your rating plate to
verify included options.
H36PVN
Corrosive
Venting Type
Burner Type
Ignition Type
Top Power Vent
Traditional
IPI Electronic Ignition
Page 3
Danger of s
Rotatin
Danger of
your h
H36PVN Power Vent Indoor Gas Fireplace
Installation
Section A: Before You Begin
Section:
Important Message
Pre-Installation Checklist
Save these Instructions
The H36PV Power Vent fireplaces must be installed in
accordance with these Instructions. Carefully read all the
Instructions in this manual first. Consult the Local Gas Branch to
determine the need for a permit prior to starting the installation.
It is the responsibility of the installer to ensure this fireplace is
installed in compliance with the manufacturers instructions and
all applicable codes.
■ Determine the desired install location of your fireplace.
■See Section 1, Dimensions on Page 5, and refer to the
Framing Section 2 for details.
■Select your type and location of your Power Vent
run: Roof Mounted (EDVRSPV58) or Wall Mounted
(EDVWSPV58).
BEFORE YOU START:
■Your termination location should be selected to provide
the shortest possible vent run.
■Lay out the Vent run; calculating the required elbows
and straight runs of 5"/8" flex or rigid pipe.
■Refer to the Section 4 on Page 10, "Installing the Power
Vent" for details.
■Montigo supplies 20' of low voltage wire, which can be
spliced to any length. This wire CANNOT run in conduit
with any other wire.
■Refer to Section 5 on Page 18, for Wiring Details.
■The gas connection is located on the bottom side of the
fireplace.
■Refer to local codes and guidelines for installation
requirements.
■Installation and repairs should be done by a qualified
contractor and must conform to:
NOTICE
Installation and repairs should be done by an
authorized gas fireplace service technician. The
appliance should be inspected before use and at
least annually by a professional. More frequesnt
cleaning may be required due to exessive lint from
carpeting, bedding material, ect. It is imperative
that control compartments, burners and circulating
air passageways of the fireplace are kept clean.
XW2016
CAUTION
Due to high operating temperatures, this appliance
should be located out of traffic & away from
furniture and draperies.
Children and adults should be alerted to the
hazards of the high surface temperature, which
could cause burns or clothing ignition.
Young children should be carefully supervised
when they are in the same room as the appliance.
Clothing or other flammable materials should not
be placed on or near the appliance.
Blank
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
Electricity
Blank
Danger for cutter
Entrapment hazard
Battery hazard
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Low temperature
Gas bottles
Strong magnetic field
Watch for
falling objects
Optical radiation
Non ionizing
radiation
Radiation
Hazardous to the
Environment
Danger of harming
your hands
Rotating parts
Corrosive
Danger overhead crane
Blank
Flammable materials
XW2018
Explosion risk
Toxic
Fork lift trucks
High voltage
Irritant
Slippery floor
Watch your step
High temperatures
Glass hazard
Danger of suffocation
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Gas bottles
Watch for
falling objects
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Cutting
Irritant
Slippery floor
Watch your step
High temperatures
Glass hazard
Danger of suffocation
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
radiation
Radiation
Hazardous to the
Environment
Danger of harming
your hands
Gas bottles
Watch for
Electricity
Danger for cutter
Cutting
Entrapment hazard
Battery hazard
Rotating parts
XW2020-When-Installed_[EN].pdf
1
1/24/2011
12:48:53 PM
• Installations in Canada must conform to the current
CAN/CGA B-149.1 and .2 Gas Installation Code and
local regulations.
• Installations in the USA must conform to local
codes, or in the absence of local codes to the National
Fuel Gas Code, ANSI Z223.1-1988.
• See Appendix C for installation within the State
of Massachusetts. This fireplace must comply with
NFPA-54 Chapter 10.
■ Refer to Section 6 Page 21, "Installing the Gas Line" for
Details.
Understanding the Basic Operation
Residential H36PV fireplace
DANGER
When this appliance is installed directly
on any combustible material other than
wood flooring, it must be installed on a
metal or wood panel extending the full
width and depth of the appliance or a
fire will occur causing serious injury,
property damage or even death.
To operate the fireplace, Montigo has supplied and installed
twenty feet of low voltage wire to this electrical control panel.
Connect the two wire harness to a standard single pole ON/
Off switch located at a location of your choice. You may also
extent these wires to any length, as long as you select a wire
of equal quality.
XW2020
Page 4
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Installation
Section 1: Installation Overview and Product Dimensions
Please review the Pre-Installation Checklist on Page 4
for general information on preparing for a successful
installation of your fireplace.
Clearances
To ensure the H-Series H36PVN Fireplaces operate safely, all
models must maintain the following clearances.
The H-Series H36PVN & fireplace
The H36PVN fireplaces may be installed in any location that
maintains proper clearances to air conditioning ducts, electrical
wiring and plumbing. Safety, as well as efficiency of operation,
must be considered when selecting the fireplace location. Try
to select a location that does not interfere with room traffic,
32”
1”
has adequate ventilation, and offers an accessible pathway for
Power Vent installation.
Clearances to Combustibles
The fireplace dimensions are shown below:
32” 8 3/4”
1”
CL
8”
8 3/4”
5”
CL
Top
23”
View
Model#
Top
Sides
Back
H36PVN
8"
0"
1"
Floor Floor
(under) (front)*
0"
0"
8”
*Note:
Finishing hardwood, laminate flooring, or tile may be placed
directly in front of fireplace, however Montigo waives responsibility for
23”
discoloration
of flooring materials. Ability to withstand heat should be
5”
discussed with the flooring manufacturer. If carpet is to laid there must
be a 12" clearance or hearth between the front of the fireplace and the
start of the carpet.
Top View
46”
2”
23”
2”
5 ¾”
46”
Nailing
Flange
2”
23” 9”
2”
5 ¾”
Access
Panel
41 ¼”
4”
9”
Nailing
Flange
¾”
10” 41 ¼”
Front View
Side View
Flexible Incoming
Gas Connection
Left
de View
Blk
Wht
31 ½”
38 ½”
Flexible Incoming
Gas Connection
¾”
Left
Power Vent
Nailing Wall Switch
Communication
Flange LVT Connection
Harness Port
Blk
Nailing Wall Switch
Flange LVT Connection
38 ½”
Front View
Power Vent
Communication
Harness Port
31 ½”
Wht
Access Panel
Main Incoming A/C
Power Connection
Right
Side View
Access Panel
Main Incoming A/C
Power Connection
Right
WARNING
View
The H36PVN Side
& H36PVL
are power vented
fireplace systems. Under no circumstances can
these model(s) be installed without a power vent
module.
For regular Horizontal vent installation use 5"/8"
model EDVWSPV58 with the rough-in kit,
EDVWSPV58F for the
For regular Vertical vent installation use 5"/8"
model EDVRSPV58 with the rough-in kit, EPVF58
for the H36PVN & H36PVL.
XW2022
Figure 1. Fireplace dimensions.
XG0649 - 031511
Page 5
H36PVN Power Vent Indoor Gas Fireplace
Installation
Section 2: Framing
Step 1. To frame in the unit first frame a rough-in enclosure with
combustible framing materials, using typical framing practices. The
rough-in frame opening for the assembled fireplace is 46" wide, x
50" high x 24" deep. See Figure 2.
NOTE: When constructing the framed opening, please ensure
that your combustible 2 x 4 header is at 50" minimum and
that there is access to install the gas line when the unit is
installed. See Figures 1 and 2a.
46”
50”
(minimum)
24”
Figure 2. Fireplace installation (combustible frame dimensions)
Step 2. Place the Fireplace in the enclosure and install the Vent pipe,
and Power Vent module. Next, Connect the Gas line and provide a
gas service shut-off valve; according to local gas codes, then secure
in place with 1/4" wood screws. Install supplied Non-combustible
header at 45½" from floor.
Non-combustible Header (supplied by montigo), install to allow
15½” of Non-combustible cement board to fasten above the
glass of the unit and Non-combustible header.
Flexible
incoming gas
connection
Secure nailing
flange to 2 x 4’s
using ¼" wood
screws.
Figure 2a. Fireplace installation, (Inlet Gas & Power Vent) .
Page 6
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Installation
Section 3: Finishing
Step 1. As shown in Figure 3; Use Non combustible Cement board,
supplied by Montigo, screw to Non-combustible Header and 2 x 4's
at sides of unit (see figure 2a on page 6) using sheet metal screws.
Non-combustible Cement Board
(supplied by montigo).
Fasten above the glass of the
unit to Non-combustible header
and 2 x 4’s at side of unit.
Figure 3. Non-combustible Cement Board the Fireplace, (supplied by Montigo).
Step 2. As shown in figure 3a; Cut standard Drywall / Wall board
to complete the installation of fireplace surround.
Combustible Drywall / Wall
Board or equivelant.
Fasten above the glass of the
unit to Non-combustible header
and 2 x 4’s at side of unit.
Figure 3a.
XG0649 - 031511
Page 7
H36PVN Power Vent Indoor Gas Fireplace
Vertical Run
Installation
16”
15”
14”
13”
12”
11”
10”
9”
8”
7”
6”
5”
4”
3”
2”
1”
To Ceiling
Drywall/
Combustible Construction
Combustible Construction
allowed in shaded area
First Combustible
Header @ 50"
from floor or 8”
from top of unit
Non-combustible
Header (supplied by
Montigo @ 6½”)
Non-Combustible
Cement Board
(supplied by Montigo)
12” 11” 10” 9” 8” 7” 6” 5” 4” 3” 2” 1”
Horizontal Run
Non-Combustible
Cement Board
(supplied by Montigo)
Glass
Figure 3b. Combustible mantle and facings. (Not to scale)
Fireplace Facing
When selecting the finish material for your fireplace, it is important
to remember the following:
If the surround of the fireplace is to be painted to match the room decor,
heat-resistant paint must be provided . Also, decorative facing must
not extend past the fireplace opening at all, because it will interfere
with the access to retainers for removal of glass door and access to
the lower compartment.
Mantels & Surrounds
National Canadian Gas Association mantel test requirements are for
fire hazard prevention to combustible materials.
Please be aware; temperatures over the mantel will rise above normal
room temperature and walls above fireplace may be hot to touch.
CAUTION
CAUTION
We recommend careful consideration
be given to the effects of elevated
mantel temperatures which may be in
excess of product design, for example:
candles, plastic or pictures. This can
cause melting, deformation, discoloration or premature failure of T.V. radio,
and other electronic components.
XW2034
Page 8
When covering the upper metal
portion of the fireplace, (as shown,
Fig.16) with a non-combustible
material, Please Note: The
decorative facing materials may
be subject to temperatures in
excess of 250° F. This should be
considered when selecting facing
materials.
XW2036
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Installation
Section 4: Installing the Power Vent
Multi-Elbow Installations
Montigo supplies a variety of power venting options The location of
the power vent should be selected and laid out to provide the shortest
possible run to an external wall or through the roof In the event that
the external power vent is not aesthetically acceptable or otherwise
infeasible, an in-line power vent can be used with this and is included
on page 17 of this instruction manual (contact Montigo for Details)
Multi-elbow installations are possible up to a maximum of six
at 90° elbows
V3
Installing a Roof Mounted Vertical Exterior Power Vent
(EDVRSPV58)
Elbow 4
This section applies to installations where the shortest possible vent
run is through the roof Refer to Appendix A - Power Vent locations,
to ensure the planned Power vent location is acceptable Once the
vent location has been established, please refer to the appropriate
section below for installation details
Venting Layout
Elbow 5
H2
V2
Elbow 2
Elbow 3
Selection of components and details of venting lay out should adhere
to the following guidelines:
H1
V1
■ Ensure there is a minimum run of 2’ of straight pipe before
the power vent
Elbow 1
■ Ensure the maximum vent run does not exceed 80’
■ Ensure the number of 90° elbows does not exceed 6
■ Ensure the number of 45° elbows does not exceed 12
Straight Venting Layout
Multi Elbow - Venting Installation
V1 + H1 + V2 + H2 + V3
(Maximum Length)
Max. #
Elbows
80 Feet
6
Figure 4a. Multi-elbow Venting Installations.
Downward Vertical Venting
Venting Installation
V (Maximum Length) Max. # Elbows
V
100 Feet
Note: The downward vent run must not exceed 6' of vent run
0
Elbow 3
Elbow 2
Figure 4 Typical straight Venting Installations.
H1
V1
V3
D = 6’ foot
MAX
Elbow 1
WARNING:
MUST
on the door gasket and/or explosion ports will result in
products of combustion leaking into the living space and
may result in carbon monoxide poisoning.
Elbow 4
H2
Elbow
Multi Elbow - Venting Installation
V1 + H1 + V2 + H2 + V3
(Maximum Length)
Max. #
Elbows
40 Feet
6
Figure 4b. Downward Venting Installations.
XG0649 - 031511
Page 9
H36PVN Power Vent Indoor Gas Fireplace
Installation
Venting Components
The following venting components and associated Montigo part
numbers are available for the EDVRSPV58:
A - Termination
EDVRSPV58
B - Rough-in Frame
EDVRSPV58F
C - Flex Sections
PLF-1 (12" Section)
PLF-2 (24" Section)
PFL-3 (36" Section)
PFL 4 (48" Section)
D - Rigid Sections
E - Elbows
F - Power Cord
Harnesses
Installation of the EDVRSPV58 External roof mounted power vent
module.
Refer to Appendix A - Power Vent locations, to ensure the planned
Vertical Power vent location is acceptable.
The EDVRSPV58 Power Vent dimensions:
Ø14”
19 1/4”
PEXT-1 (12" m/f Section)
PXT-20 (20" Section)
PEXT-2 (24" m/f Section)
PEXT-3 (36" m/f Section)
PEXT-4 (48" m/f Section)
2”
PEL-90MM (m/m 90º Elbow
PEL-90FF (f/f 90º Elbow
PEL-90FM (f/m 90º Elbow)
PEL-45FM (f/m 90º Elbow)
EPVH10-10 foot power cord & harness
EPVH20-20 foot power cord & harness
EPVH30-30 foot power cord & harness
EPVH40-40 foot power cord & harness
EPVH50-50 foot power cord & harness
EPVH60-60 foot power cord & harness
EPVH70-70 foot power cord & harness
EPVH80-80 foot power cord & harness
EPVH70-70 foot power cord & harness
EPVH70-70 foot power cord & harness
EPVH80-80 foot power cord & harness
EPVH90-90 foot power cord & harness
EPVH100-100 foot power cord & harness
8 1/2”
Ø 1/2”
Front View
18”
18”
Top View
The EDVRSPV58F Rough-in Frame dimensions:
Connection and installation of the vent components
should adhere to the following guidelines:
6”
„„
Connect all vent sections using a minimum of three sheet
metal screws on the outer pipe flue.
„„
Ensure the pipe ends male to female slide in a minimum
of 1 1/2“ of overlap.
„„
Ensure all runs are supported with a minimum of 3 supports
per 10’ of venting.
Ø 8”
„„
When hanging/ supporting venting, ensure that 1” clearance
is maintained on all sides to any combustible material.
Front View
„„
Ensure when cutting sections of rigid pipe to maintain
integrity of internal supports.
18”
„„
Place the springs, supplied with the pipe kit, between the
outer and inner pipes to keep the pipes separate and avoid
any possible hot spots.
„„
Montigo recommends the use of a flex section for the final
pipe connected directly to the fireplace offering greater
flexibility of installation and absorption of movement.
„„
All exterior joints in venting should be sealed with high heat
silicone 706 High Temp.
14”
18”
Top View
Page 10
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Installation
Installing the external roof mounted power vent module
Step 1.
Construct a Vertical Chase for the termination opening to meet
the following requirements:
Step 3.
Install the Power Vent Rough-in Kit. Pull wire harness through
the supplied hole in the bottom corner of the rough-in box, and snap
into the slot provided, (See figure 5b inset).
Power Vent
Rough-in Kit
■ Opening Size must be: 14 1/2" x 14 1/2" x 18" Min. height.
14½"
14½"
Electrical Harness
Connerctor Location
18"
Electrical
Harness
Figure 5. Construction, Rough-in framing.
Figure 5b. Installation of Rough-in Kit
Step 2.
Install the Vent pipe female end up, and 2" to 3" MAX. from the
top of the Constructed Chase. Also, at this point install the Electrical
harness, (EPVH-(10-100) that will communicate with the Power
Vent Module.
2" to 3" Max.
Step 4.
Install fasteners around perimeter of Rough-in Kit. (Holes supplied
for ease of installation)
Electrical Harness
with connection
Vent Pipe
Install Fasteners around
perimeter of Rough-in Kit
Vent Chase
Figure 5c. (Fasten Rough-in Kit to framing)
Figure 5a. Installation, Vertical Vent pipe. (female end top end).
WARNING
All venting material must be sealed with high heat
silicone sealant RV230. All venting material to be
Montigo flex pipe, with as few joints as possible.
All joints use MVA vent splice, sealed thoroughly
with silicone. Montigo will not be held responsible
for any water damage that may occur from not
installing the equipment as specified by this
document.
XW2024
XG0649 - 031511
Figure 5d. (Installed Stainless steel cover)
Page 11
H36PVN Power Vent Indoor Gas Fireplace
Installation
Step 5.
Install the Power Vent, Roof-top Stainless steel cover over the
Installed Rough-in Kit. (You can see the Electrical harness connector
in the top right corner).
Electrical Harness
from Power Vent
Stainless Steel
Fasteners
Figure 5e.
Figure 5f.
Step 6.
Install the Power Vent Module Power / communication harness.
Hold the Power Vent in close proximity of the assembled Chase,
(with stainless steel cover attached) and plug in the Power Vent
communication / Power Cord. (Note the direction and orientation of
the plug socket). (See Figure 5e & Figure 5f)
Figure 5h. (Installed Power Vent Module)
Step 8.
Install (3) three stainless steel fasteners around Power Vent
Module @120 degrees (penetrating through the inner stainless steel
vent cover)
Vertical Roof Top
Power Vent
Install Power Vent Module
with Power / Communication
Harness
Vertical Roof Top
Power Vent Roughin Kit
CAUTION
■ Vent terminations can be very hot. The
termination is to be installed higher than 7 feet
above a public walkway.
■ Do not obstruct, or attempt to conceal, the vent
termination. These actions will affect the operation
of the fireplace, and may be hazardous.
■ In heavy snow areas, take extra care to
prevent snow buildup from obstructing the vent
termination.
XW2026
CAUTION!
Vent terminations can be very hot. The termination is to be installed higher than 7 feet above a public walkw
Step 7.
Do not obstruct, or attempt to conceal, the vent termination. These actions will affect the operation of the fi
In Module.
heavy snow
takeVent
extra
care to prevent snow buildup from obstructing the vent termination.
Install the Power Vent
Place areas,
the Power
Module
Figure 5g. (Installation of Power Vent Module)
over the stainless steel cover flange and vent pipe, aligning the
Power Vent into final position. Ensure the Harness is placed down
in the Rough-in box when placing the Power Vent Module into place.
The Power Vent Module will sit flush with the stainless steel cover
if installed correctly.
Page 12
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Installation
Installing a Wall Mounted Vertical Exterior Power Vent
(EDVWSPV58)
This section applies to installations where the shortest possible vent
run is through an exterior wall. Refer to Appendix A - Power Vent
locations, to ensure the planned Power vent location is acceptable.
Once the vent location has been established, please refer to the
appropriate section below for installation details.
Multi-Elbow Installations
Multi-elbow installations are possible up to a maximum of six
at 90° elbows.
Elbow 6
Once the vent location has been established, please refer to the
appropriate section below for installation details.
Elbow 4
Elbow 5
Venting Layout
Elbow 2
■Ensure there is a minimum run of 2’ of straight pipe before
the power vent.
■ Ensure the maximum vent run does not exceed 100’.
■ Ensure the number of 90° elbows does not exceed 6.
■ Ensure the number of 45° elbows does not exceed 12.
H2
V2
Selection of components and details of venting lay out should adhere
to the following guidelines:
H3
V3
Elbow 3
H1
V1
Elbow 1
H
V
Multi Elbow - Venting Installation
V1 + H1 + V2 + H2 + V3 = H3
(Maximum Length)
Max. #
Elbows
80 Feet
6
Figure 6a. Multi-elbow Venting Installations.
Downward Vertical Venting
Note: The downward vent run must not exceed 6' of vent run.
Venting Installation
V + H (Maximum Length)
Max. #
Elbows
80 Feet
6
H1
Figure 6. Typical Venting Installations.
V
D
WARNING
All venting material must be sealed with high heat
silicone sealant RV230. All venting material to be
Montigo flex pipe, with as few joints as possible.
All joints use MVA vent splice, sealed thoroughly
with silicone. Montigo will not be held responsible
for any water damage that may occur from not
installing the equipment as specified by this
document.
XW2024
H2
Multi Elbow - Venting Installation
V1 + H1 + D + H2
(Maximum Length)
Max. #
Elbows
40 Feet
6
Figure 6b. Downward Venting Installations.
XG0649 - 031511
Page 13
H36PVN Power Vent Indoor Gas Fireplace
Installation
Venting Components
The following venting components and associated Montigo part
numbers are available for the EDVWSPV58:
A - Termination
EDVRSPV58
B - Rough-in Frame
EDVRSPV58F
C - Flex Sections
PLF-1 (12" Section)
PLF-2 (24" Section)
PFL-3 (36" Section)
PFL 4 (48" Section)
D - Rigid Sections
E - Elbows
F - Power Cord
Harnesses
PEXT-1 (12" m/f Section)
PXT-20 (20" Section)
PEXT-2 (24" m/f Section)
PEXT-3 (36" m/f Section)
PEXT-4 (48" m/f Section)
Installation of the EDVWSPV58 external wall mounted power vent
module.
Refer to Appendix A - Power Vent locations, to ensure the planned
Vertical Power vent location is acceptable.
The EDVWSPV58 Power Vent dimensions:
11 1/16"
10 9/16"
11 1/16"
11 1/16"
9 3/4"
5
PEL-90MM (m/m 90º Elbow
PEL-90FF (f/f 90º Elbow
PEL-90FM (f/m 90º Elbow)
PEL-45FM (f/m 90º Elbow)
9.0
EPVH10-10 foot power cord & harness
EPVH20-20 foot power cord & harness
EPVH30-30 foot power cord & harness
EPVH40-40 foot power cord & harness
EPVH50-50 foot power cord & harness
EPVH60-60 foot power cord & harness
EPVH70-70 foot power cord & harness
EPVH80-80 foot power cord & harness 9.0
EPVH70-70 foot power cord & harness
EPVH70-70 foot power cord & harness
EPVH80-80 foot power cord & harness
EPVH90-90 foot power cord & harness
EPVH100-100 foot power cord & harness
10 9/16"
5
The EPVF58 Rough-in Frame dimensions:
EPVF58 DIMS (2).pdf 1 3/7/2011 9:16:30 AM
Connection and installation of the vent components should
adhere to the following guidelines:
■Connect all vent sections using a minimum of three sheet
metal screws on the outer pipe flue.
■Ensure the pipe ends male to female slide in a minimum
of 1 1/2“ of overlap.
■Ensure all runs are supported with a minimum of 3 supports
per 10’ of venting.
■When hanging/ supporting venting, ensure that 1” clearance
is maintained on all sides to any combustible material.
■Ensure when cutting sections of rigid pipe to maintain
integrity of internal supports.
■Place the springs, supplied with the pipe kit, between the
outer and inner pipes to keep the pipes separate and avoid
any possible hot spots.
■Montigo recommends the use of a flex section for the final
pipe connected directly to the fireplace offering greater
flexibility of installation and absorption of movement.
14 1/16"
14 1/4"
9 11/16"
12 5/16"
4
12 1/8"
1 1/2"
4 9/16"
8
9 11/16"
ISOMETRIC VIEW
■All exterior joints in venting should be sealed with high heat
silicone RV230.
Page 14
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Installation
Installing the external wall mounted power vent module
Step 1. Construct a frame for the termination opening to meet the
following requirements:
■ Opening Size must be: 14 1/2" x 14 1/2".
Step 4.
Insert the conduit from the Power Vent Module into the rough-in
frame through the two top right entry holes. Remove the nut from the
supplied strain relief and place as shown, Figure 7c.
Strain Relief
14 1/2”
(Opening)
Power Vent Conduit
Strain Relief
Nut
14 1/2”
(Opening)
Figure 7. Framing the Opening for Power Vent
Figure 7c. Installation of Power Vent Conduit
Step 2.
Step 5.
Insert the Power Vent Rough-in Box as shown in Figure 7a.
Fasten the Box securely in place with Screws or nails. Apply exterior
sheathing and finishing if required.
Framing
Securely fasten bottom Collar pan into the Rough-in frame using
the existing hardware, (4-pcs). Tighten Strain Relief nut onto Strain
relief.
Step 6.
Fasteners
Pull Power Vent Connector, (from behind) half-way through
supplied hole in conduit mounting frame, and snap into place, (notches
in two plastic wing clips. Orientation not critical).
Strain Relief & tightened nut
Rough-in Frame
Power Vent Conduit
Conduit
mounting
frame
Power Vent
Connector
Figure 7a. Orientation, Placing the Power Vent Inner Box
Step 3.
Next, remove the bottom collar and conduit mounting frame as
shown Figure 7b. (Place removed hardware in a handy location for
re-assembly).
Tightened hardware, 4-pcs.
Figure 7d. (Installing Conduit connector & conduit mounting frame)
Step 7.
Fasten Conduit mounting frame into place using existing hardware,
(6-pcs). (Coil conduit in behind cover.)
Figure 7b. Installation of Rough-in Kit
XG0649 - 031511
Page 15
H36PVN Power Vent Indoor Gas Fireplace
Installation
Installed Power Vent
Connector
Tightened hardware, 6-pcs.
CAUTION
■ Vent terminations can be very hot. The
termination is to be installed higher than 7 feet
above a public walkway.
■ Do not obstruct, or attempt to conceal, the vent
termination. These actions will affect the operation
of the fireplace, and may be hazardous.
■ In heavy snow areas, take extra care to
prevent snow buildup from obstructing the vent
termination.
Figure 7e. (Assembled Rough-in Kit)
Step 8.
Install the Power Vent Power / communication harness. Hold
the Power Vent in close proximity of the assembled Rough-in Kit,
and plug in the Power Vent communication / Power Cord. (Note the
XW2026
CAUTION!
direction and orientation
of the pins inside the Power Vent connector,
7f).
Vent terminations can be very hot. The termination is to be installed higher than 7 feet above a public walkw
snap together). (Figure
Do not obstruct, or attempt to conceal, the vent termination. These actions will affect the operation of the fire
In heavy snow areas, take extra care to prevent snow buildup from obstructing the vent termination.
Communication
Harness.
TOP of Power Vent,
(Note Quantity of
louvers).
Note louver
direction
Figure 7f. (Installation of Power Vent communication harness)
Step 9.
Install the Power Vent. Place the Power Vent into the Rough-in
frame, aligning the Power Vent into final position. Ensure the Harness
is placed down in the Rough-in box when placing the Power Vent.
(Secure the Power Vent in Place with the supplied hardware).
Tightened hardware,
4-pcs.
Figure 7g. (Completed Installation of Power Vent)
Page 16
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Installation
Installing an In-Line Linear Power Vent (LDVPV58)
This section applies to installations where an external roof
or wall mounted power vent is not aesthetically acceptable
or feasible.
Example B. Horizontal mounting with horizontal termination
Venting Installation
Venting Layout
Selection of components and details of venting lay out should
adhere to the following guidelines:
„„
Ensure the maximum vent run does not exceed 60'
„„
Maximum vent run must be reduced by 10’ for 1’ of pipe
running in a vertical downward direction
„„
Minimum
Vent Run**
Max. #
Elbows
60 Feet
20 Feet
3
** from fireplace to in-line power vent
Ensure there is a minimum run of 2’ of straight pipe between
the fireplace and the power vent
„„
Maximum
Vent Run
90deg
Elbow
Horizontal Installed
Linear Power Vent
Termination
LDVPV58
Horizontal Run Flex Pipe
Ensure the number of 90º elbows does not exceed 3 (maximum
allowable vent run must be reduced by 10’ for every additional
90º elbow added)
„„ Ensure the number of 45º elbows does not exceed 6
Linear Power Vent - Horizontal Termination
Option
Vertical
Flex Pipe
Snorkel
Termination
Option
90deg
Elbow
90deg
Elbow
Flush
Termination
VLWB-8
Example A. Vertical mounting with horizontal termination
Venting Installation
Maximum
Vent Run
Minimum
Vent Run**
Max. #
Elbows
60 Feet
2 Feet
3
Figure 7a. Horizontal Vent for the Linear Power Venter.
** from fireplace to in-line power vent
Maximum allowable vent run must be reduced by ten feet (10'-0"
for every additional 90° elbow added. With a snorkel Termination,
reduce the total vent run by an additional twenty feet (20'-0"). Figure's
7 and 7a.
90deg
Elbow
Vertical
Flex Pipe
Option
Snorkel
Termination
Vertical Installed
Linear Power Vent
LDVPV58
90deg
Elbow
Venting Installation
Termination
Horizontal Run Flex Pipe
2’-0 ”
MIN
Example C. Horizontal mounting with downward vent run and
horizontal termination
Maximum
Vent Run
Minimum
Vent Run**
Max. #
Elbows
40 Feet
2 Feet
3
** from fireplace to in-line power vent
Maximum allowable vent run must be reduced by ten feet (10'-0")
for every additional 90° elbow added. Also, deduct ten feet (10'-0")
of vent length for every one foot (1'-0") of vent run traveling in a
downward direction.
Horizontal Installed
Linear Power Vent
90deg
Elbow
Option
90deg
Elbow
Flush
Termination
VLWB-8
LDVPV58
Vertical
Flex Pipe
90deg
Elbow
6’-0”
Max.
Horizontal Run Flex Pipe
Termination
Figure 7. Vertical Mounting for the Linear Power Venter
Figure 7b. HorizontaI Linear Power Vent with Downward vent
and Horizontal Vent Run to Termination.
CAUTION
■ Vent terminations can be very hot. The
termination is to be installed higher than 7 feet
above a public walkway.
■ Do not obstruct, or attempt to conceal, the vent
termination. These actions will affect the operation
of the fireplace, and may be hazardous.
■ In heavy snow areas, take extra care to
prevent snow buildup from obstructing the vent
termination.
XW2026
CAUTION!
Page 17
XG0649 - 031511
Vent terminations
can be very hot. The termination is to be installed higher than 7 feet above a public walkway.
Do not obstruct, or attempt to conceal, the vent termination. These actions will affect the operation of the fireplace, and may be hazard
H36PVN Power Vent Indoor Gas Fireplace
Installation
Linear Power Vent - Vertical Termination
Venting Installation
Maximum
Vent Run
Minimum
Vent Run**
Max. #
Elbows
80 Feet
2 Feet
3
Venting Components
The following venting components and associated Montigo
part numbers are available for the LDVPV58:
** from fireplace to in-line power vent
Maximum allowable vent run must be reduced by ten feet (10'-0") for
every additional 90° elbow added. Figure's 8 and 8a.
Example A. Vertical Mounting with Vertical Termination
A - Termination
DVPV58
B - Power Vent
LDVPV58
C - Control Module
RHSIT05
D - Flex Sections
PFL-1 (12" Section)
PFL-2 (24" Section)
PFL-3 (36" Section)
PFL-4 (48" Section)
E - Rigid Sections
PEXT - 1 (12" m/f Section)
PXT-20 (20" section)
PEXT - 2 (24" m/f Section)
PEXT - 3 (36" m/f Section)
PEXT - 4 (48" m/f Section)
F - Elbows
PEL-90MM (m/m 90° Elbow)
PEL-90FF (f/f 90° Elbow)
PEL-90FM (f/m 90° Elbow)
PEL-45FM (f/m 45° Elbow)
G - Power Cord
Harnesses:
EPVH10 -10 foot power cord and harness
EPVH20 -20 foot power cord and harness
EPVH30 -30 foot power cord and harness
EPVH40 -40 foot power cord and harness
EPVH50 -50 foot power cord and harness
EPVH60 -60 foot power cord and harness
EPVH70 -70 foot power cord and harness
EPVH80 -80 foot power cord and harness
EPVH90 -90 foot power cord and harness
EPVH100 -100 foot power cord and harness
Termination
2’-0 ”
MIN
Vertical
Flex Pipe
90deg
Elbow
90deg
Elbow
Vertical Installed
Linear PowerV ent
LDVPV58
2’-0 ”
MIN
90deg
Elbow
90deg
Elbow
Figure 8. Vertical Vent for the Linear Power Venter
Example B. Vertical Mounting with Vertical Termination
Termination
2’-0 ”
MIN
90deg
Elbow
90deg
Elbow
Vertical Installed
Linear Power Vent
LDVPV58
90deg
Elbow
90deg
Elbow
Vertical
Flex Pipe
Connection and installation of the vent components
should adhere to the following guidelines:
„„
Connect all vent sections using a minimum of three sheet
metal screws on the outer pipe flue.
„„
Ensure the pipe ends male to female slide in a minimum
of 1 1/2" of overlap.
„„
Ensure all runs are supported with a minimum of 3 supports
per 10’ of venting.
„„
When hanging/ supporting venting, ensure that 1” clearance
is maintained on all sides to any combustible material.
„„
Ensure when cutting sections of rigid pipe to maintain
integrity of internal supports.
„„
Place the springs, supplied with the pipe kit, between the
outer and inner pipes to keep the pipes separate and avoid
any possible hot spots.
„„
Montigo recommends the use of a flex section for the final
pipe connected directly to the fireplace offering greater
flexibility of installation and absorption of movement.
„„
All exterior joints in venting should be sealed with high
heat silicone RV230.
Figure 8a. VerticaI Linear Power Vent with Vertical Vent Run
Page 18
XG0649 - 031511
Installation
13 5/16"
Installation of the LDVPV58 power vent module:
1. The linear power vent can be installed to existing stud
construction or directly to cement wall or roof. The LDVPV58
must maintain the clearance to combustibles as shown in Figure
9a. The required service access panel must be framed at 28"
X 18". To enclose the service access panel, (at less than 2") a
minimum 30% free air must be supplied at all times. 20 3/16"
2. Plug the power cord into the available slot in the linear power
vent.
3. Secure all venting joints with at least three screws and ensure
that the joints are properly sealed by applying high temperature
silicone.
16 1/2
34 7/8
1/2
MIN
Vent
18 1/8"
Louvres
2 MIN
Figure 9b. 5
MIN
5
5
MIN
8
LDVPV58 Power Vent framing dimensions.
Recessed Termination Installation (VLWB-8) Refer to Appendix A Termination locations
11
33
Access Cover
The VLWB-8 termination is
designed to be installed flush
with the exterior of the building.
This recessed design uses 5"/8"
vent and allows the installation to
be clean and flush so it does not
interfere or have an impact with
your architectural design.
8
ISOMETRIC VIEW
(NTS)
2
Top View
Side View
Figure 9. LDVPV58 Power Vent overall dimensions.
Framing
12 9/64" Dimensions
5 MIN
28 clearance
for Cover access
/8"
H36PVN Power Vent Indoor Gas Fireplace
1
181/2
5 MIN
Figure 10. TERMINATION, VERTICAL MOUNT, 5/8", 12" X 20" BOX
Linear Power Vent recessed Termination.
DIMENSIONS ARE IN INCHES
DATE
NAME
TOLERANCES:
NOTE:
7/29/2010
LF
DRAWN BY
1/32"
FRACTIONAL
.015"
TWO PLACE DECIMAL The H36PVN
requires
a specific volume of atmospheric interchange
CHECKED
BY
.005"
THREE PLACE DECIMAL
to
operate
properly
and efficiently
MATERIAL
ALL BENDS ARE ASSUMED
SIZE DWG. NO.
VLWB-8
TO BE 90 UNLESS NOTED
requires a MIN 80in/sq.Aair movement to function.
 The fireplace
FINISH
OTHERWISE.
304 S.S.T.
SCALE NTS WEIGHT:
grille OF
must
alsoHEATING
be able
to shed
water, not
 The
DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN
PERMISSION
CANADIAN
PRODUCTS
IS PROHIBITED.
Access Cover
moisture to enter the unit.
allowing any
Must be left clear on both
ends of Power Vent for
adequate ventilation.
Figure 9a. LDVPV58 Power Vent framing dimensions.
XG0649 - 031511
Page 19
SHEET 1 O
H36PVN Power Vent Indoor Gas Fireplace
Installation
Section 5: Wiring
The Fireplace A/C power and Power Vent harness's must be installed
before completing the installation of the H36PVN Fireplace. These
connections are made from the RH-Side of the fireplace, Figure 12
through Figure 12f.
Step 2. Locate all the Power vent connections & ports, Figure 12b.
Power Vent,
Communication port.
Power vent communication conduit, A/C
connection port
Incoming A/C
Power Connection
Figure 12b. Locate Power vent connections.
Figure 12. Incoming A/C Power , (connect per. Local Codes).
Install the Power Vent connections as described
below:
Note: To access the fireplace electrical connections from the
firebox follow the procedures described in figure 22 through 26.
Step 1. Remove the exterior Access cover, shown Figure 12a.
Power Vent,
& A/C Access
Cover
Step 3. Remove the Power Vent communication port cover from
cabinet, (as supplied) Figure 12c. (Philips head screwdriver
required).
Step 4. Place the cover plate on the Conduit, then tighten the strain
relief nut onto the threads protruding through backside of cover plate,
Figure 12e.
Figure 12a. Remove Exterior Access Cover.
Page 20
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Installation
Step 5. Route the Power Vent Comunication conduit into the cover
as shown, and connect to the communication Port, Figure 12d.
Installing The Remote Switch
Note
orientation of
connector
The H36PVN's Remote LVT (Low Voltage) Switch conduit is located
on the RH Side of the fireplace.
Note: The switch location must not exceed 30' from the fireplace.
Power vent
communication
harness port
Power vent
communication
port cover.
Power vent
communication
harness.
Figure 12c. Remove Exterior Access
Cover.
Figure 12d.
connections.
Locate Power vent
Note orientation of conduit plug into the Port, (flat side / notches).
Step 6. Re-Install the communication harness Port cover, Figure
12e. (Philips head screwdriver required).
Remote
Switch LVT
Figure 12f. Installing the Remote LVT Switch.
Step 7. Tighten Power Vent Strain relief adjustmsent screw, Figure 12e.
Power vent
communication
port cover strain
relief.
Power vent
communication
port cover
fasteners.
Figure 12e. Installing Conduit Port Cover Plate.
Figure 12g. Electrical Enclosure Dimensions
XG0649 - 031511
Page 21
H36PVN Power Vent Indoor Gas Fireplace
Installation
WARNING
If the information in these instructions is
not followed exactly, a fire or explosion
may result causing property damage,
personal injury or death.
XW2008
Figure 13. Wiring schematic for the H36PVN.
Page 22
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Installation
Figure 13a. H36PVN, SIT IPI Wiring Schemmatic
Conduit & Wiring clearances
Connect the wiring to the linear power vent as outlined in the previous section, and connect the wiring to the fireplace as outlined in the
H36PVN schematic, figure 13. Ensure that the proper clearances are
maintained for the wiring and conduit. When installing the wiring it
must never run above the vent run and it must be at least 1" clear of
all venting.
1” Clearance
Figure 13b. Conduit and Wiring Clearances.
XG0649 - 031511
Page 23
H36PVN Power Vent Indoor Gas Fireplace
Installation
Section 6: Installing the Gas Line
FUEL CONVERSION
„„
Verify that your fireplace is compatible with your available
gas type. (Natural Gas or Propane shown by "N" or "L" in
your model number
„„
If gas type is not compatible, contact your local Montigo
representative to purchase a conversion kit.
„„
Conversion kits must be installed by a qualified service
technician.
Figure 14. Gas line access. (See Figure 1,
L-H Side View)
10”
Back of
Fireplace
GAS PRESSURE
„„
Optimum appliance performance requires proper input
pressures.
„„
Gas line sizing requirements will be determined in ANSI
Z221.3 National Fuel Gas Code in the USA and CAN/CGA
B149 in Canada.
Pressure requirements are:
4”
Flexible Input
Gasline,
(Supplied)
Gas line & valve: Exterior Access
3”
The H36PVN is supplied one (1) one exterior access Panel (LH-side
firebox). This panel is fastened directly to the exterior of the firebox
with sheet metal screws. To remove the panel follow the steps below:
Pressure Requirements
Gas Pressure
Natural Gas
Propane
Minimum Inlet Pressure
5.5" W.C.
11" W.C.
Manifold Pressure
3.5" W.C.
10" W.C.
„„
The manifold outlet pressure is set from the factory to the
appropriate pressure but should be verified.
„„
To check pressures, control valves have a provision to remove
a 1/8” N.PT. plug to be fitted with a hose barb.
„„
Montigo requires a service shut off valve be located in an
accessible location to isolate the gas supply.
„„
Only install gas shut-off valves approved for use by the state,
province, or other governing body in which the fireplace is
being installed.
Exterior gas
access panel
hardware, 10-pcs.
Figure 15a. (Inset)
GAS CONNECTION
„„
See Figure 22 below for location of gas line access.
„„
Flexible gas connectors must not exceed 3 feet in length,
unless allowable within local regulations.
„„
Connect incoming gas line to the 1/2"or 3/8" gas inlet port.
„„
Purge all air out of gas line.
„„
Check appliance connection, valve and valve train under
normal operating pressure with a commercially available
leak check solution.
„„
Figure 15. (Removing the Gas valve
panel hardware).
Gas In, Figure 14
Gas Valve
DO NOT USE A FLAME OF ANY KIND TO TEST FOR
LEAKS.
Note:
After gas line is connected, each appliance connection,
valve and valve train must be checked while under
normal operating pressure with either a liquid solution, or
leak detection device, to locate any source of leak. Tighten
any areas where bubbling appears or leak is detected until
bubbling stops completely or leak is no longer detected.
Figure 15b. (Incoming gas supply line (supplied by Montigo)
and top of Gas valve).
NOTICE
Important Note: The flexible gas line supplied with the H36PV*
may not be acceptable in the jurisdiction
which this fireplace is being installed. Please
check the Local Gas codes or bylaws for the
State or Province prior to installation.
When pressure testing the fireplace,
Gas line, and input system follow the
appropriate local codes or your area.
DO NOT connect the fireplace to
pressures in excess of 1/2lb. This will
damage the gas control valve.
XW2032
Page 24
XG0649 - 031511
Section 7:
Installing & Removing the Door
H36PVN Power Vent Indoor Gas Fireplace
Installation
Section 7: Installing & Removing the Door
Removing the doors:
The doors are removed in a few simple steps.
Follow the steps below to remove the Vertical Door trim, place the
Door removal tool, and then remove the door. Replace all the parts
in reverse order.
Step 3. Hold the Glass Removal Tools firmly, Lift the door upward,
into the top door frame, Figure 17c. Then pull the bottom of the glass
door downward, and tilt outward from the bottom fireplace door frame.
Figure 17d. NOTE: Read ALL the instruction supplied with the tool,
and follow the associated operating procedures.
Step 1. Remove the two (2) Vertical Trim pieces, (LH & RH). Pulling
firmly with your fingers, remove from the bottom then the top. (See
Figures 17 & 17a). Other side Typical.
Lift Upward into
the door frame.
Lift Downward
& away from frame.
Figure 17c. (Lift the door
upward)
Figure 17d. (Lift the bottom of
the door outward).
Step 4. Still holding the Glass
Removal Tool firmly, remove the door
outward, and away from the Fireplace,
Figure 17e.
Step 5. Place the door in a safe
location while maintenance, cleaning
or other operation are in progress.
Figure 17. (Remove LH Trim)
NOTE: Read ALL the instruction
supplied with the tool, and
follow the associated operating
procedures.
Figure 17a. (Remove RH Trim)
Step 6. To replace, See Installing
the Door, Below.
Step 2. Remove the supplied glass lifting tool from the packaging.
Place in the center of the Glass door as shown, and activate the
suction feature of the tool, Figure 17b. NOTE: Read ALL the instruction
supplied with the tool, and follow the associated operating procedures.
Figure 17e.
Installing the Door:
To install the door, follow Steps 1 and 4 above, (in reverse order)..Hook
the top edge of the door frame into place. Lower and rest the door
frame in place and fasten the buckles. See figures 28a and 28b.
NOTICE
Do not use ammonia based or abrasive
cleaners on the glass, they will
permanently etch the surface. Use an
approved gas fireplace glass cleaner
such as Kel-Kem or White off.
Figure 17b. Supplied Glass lifting tools.
XW2000
XG0649 - 031511
Page 25
H36PVN Power Vent Indoor Gas Fireplace
Installation
Section 8: Installing the Log Set
Installing the Logs:
The H36PVN is supplied with six (6) piece ceramic fibre logs. Install
as described below:
Step 1. Unpack the logs and handle them very carefully. Set them
aside in a safe location until required.
Step 3.Position Back Log 'A' from the previously unpacked package,
(Figure 18). Place the Log upright, (as shown Figure 18d) and
move the Log flush against the sheet metal Back Pan. Without
pressing the Log down, move it as far to the left as possible,
bumping the bottom Left corner against the alignment tab,
(Figure 18a & 18d). Lastly, Press the Log FIRMLY downward,
onto the sharp spikes, shown in Figure 18a & 18e.
Log A
Figure 18. Packaged LogSet as supplied from Montigo.
Log A Retaining Clip
Figure 18d. Location of Log 'A'.
Log A back-pan
Log A
Alignment Tab
Move Log ‘A’ left
and bump against
Alignment Tab
Log A Spikes
Log C Rest
Log D Rest
Log D
Spikes
Log ‘A’ Spikes
Log B cradle
& Spike
Log C
Spikes
Log B Rest
Left end Rest
Alignment Tab
Log E Spike
Figure 18a. Log Grate Details & identification.
Step 2. L
ocate the Log Back Pan Retaining clip, Figure, 18a above
and remove, Figures, 18b & 18c. Place in a safe location
(Philips head screwdriver required).
Figure 18e. Alignment of Log 'A'.
Figure 18f. Log 'A' Spikes, Figure 18a.
Step 4.Once the 'Back Log 'A' is in it's final Position, hold the log
in place, and reinstall the Retaining Clip (removed earlier).
Press down the Clip for the sharp teeth to penetrate into the
top of the Log. (Figure 18g). (Philips head screwdriver
required).
Figure 18b.
Figure 18c.
Figure 18g. Securing Log 'A'.
Page 26
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Installation
Step 5. Position the Bottom Right Log 'B' and place Right end in the
sheet metal cradle (located at the far right of the Log Grate), Figure,
18h. and Log Rest in the center of the burners, Figure, 18a. Press
FIRMLY onto the spikes. Note location of hole feature in Log.
Step 8. Place Front Left Log 'E', with the Knots pointing in the
directions shown, Figure, 18k. Place the Darker, narrow end on
top of Log 'A' as shown, (arced line). Press FIRMLY onto the sharp
spike at Lower end, Figure 18a.
Knot
Log A
Log B
Log E
Knot
Figure 18h. Positioning of Log (B).
Step 6. Position Bottom Center Log 'C', with the flat edge down.
and place square end inside Log Rest, aligning the center of the Log
with the Spikes, Figure, 18a. Press FIRMLY, seating the Log onto
the sharp spikes, Figure 18i. Note the color variation in the Log.
Figure 18k. Installation of Log 'E'.
Step 9. Position Front Right Log 'F', with the Knots pointing in the
directions shown, Figure, 18l. Place the Lighter, narrow end on
top of Log 'E' as shown, (arced line). Align for length and location,
Figure 18k.
Knot
Knot
Log E
Log F
Log C
Knot
Figure 18i. Installation of Log 'C'.
Step 7. Place Bottom Left Log 'D', with the flat edge down. and
place square end inside Log Rest, aligning the center of the Log with
the Spikes, Figure, 18a. Press FIRMLY, seating the Log onto the
sharp spikes, Figure 18j. Note the color variation in the Log.
Figure 18l. Installation of Log 'F'.
Log D
Figure 18j. Installation of Log 'D'.
XG0649 - 031511
Figure 18m. Completed Log Set Installation.
Page 27
H36PVN Power Vent Indoor Gas Fireplace
Operation
Section 9: Start-up Sequence
WARNING
If the information in these instructions is
not followed exactly, a fire or explosion
may result causing property damage,
personal injury or death.
XW2008
Startup Sequence:
1) Turn the wall switch ON
4) This may need to be done three or four times to bleed all of the
air out of the gas lines within the fireplace
2) The blowers will start and within 10 seconds the glow plugs will
start to glow
3) If the pilot does not light the gas valves willl turn the glow plugs
off after 20 seconds
5) Turning the switch OFF and then ON again will reset this start
up sequence
6) Once the pilots are burning the main burner will turn on and
the fireplace will be functional for a quick start up on next use.
CAUTION
■ This fireplace has been set up at the factory for a
determined air volume though the venting system.
■ This fireplace will not operate unless the correct
air movement is detected by our control system..
■ Please consulted with your contact person at
Montigo should you have any problems with your
start up.
XW2040
Page 28
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Operation
Proflame SIT Electronic Ignition
For Your
Safety
- READ
BEFORE
LIGHTING:
with
American
Flame Electronic
Ignition
WARNING
If the information in these instructions is
not followed exactly, a fire or explosion
may result causing property damage,
personal injury or death.
XW2008
A.This appliance is equipped with an ignition system that lights
the pilot burner automatically. Do not attempt to light the pilot
by hand.
B.BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
What To Do If You Smell Gas:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbour's phone. Follow the gas
supplier's instructions.

If you cannot reach your gas supplier, call the Fire Department.
C.Use only your hand to push in or turn the gas control knob. Never use tools.
If the knob will not push in or turn by hand, don't try to repair it, call a qualified
service technician. Force or attempt to repair may result in a fire or explosion.
D.Do not use this appliance if any part has been under water. Immediately
call a qualified service technician to inspect the appliance and to replace any
part of the control system, and any gas control which has been under water.
Lighting Instructions:
1. STOP! Read the safety information above on this label.
2. Remove the lower Horizontal access panel.
3. Turn Incoming gas valve to the ON" position.
4.Wait 5 minutes to clear out any gas. If you smell gas, STOP!
Follow "B" in the safety information above on this label. If you
don't smell gas, go to the next step.
5. Turn wall switch "ON".
6. If the Fireplace does not light, the System will cycle through two
trials, (one minute audible clicking, thirty seconds of silence, and
then another one minute of audible clicking). If the system locks
out due to inadequate gas flow, refer to "Troubleshooting", Page
20.
7. After completion of the information in the Troubleshooting section,
Repeat step 5.
8.If the system will not function correctly, follow the instructions
"To Turn Off Gas To Appliance" and call your service technician
or gas supplier.
EV1 (Pilot
burner)
EV2 (Main
burner)
Pilot Adjust Screw
Pilot Sensor
Lockout Reset Key
Diagnostic Terminal
Igniter
Ground
EV1 (Pilot burner)
EV2 (Main burner)
Power
Gas "In"
Incoming Gas
Line, Shut-off
Valve
Gas "Out"
To fireplace
Main burner
Command (Wall
switch)
To Turn Off Gas To Appliance:
1. Turn off remote switch.
3. Turn the incoming gas control valve to "Off".
2. Remove the lower Horizontal access panel.
4. Replace the lower Horizontal access panel.
XG0649 - 031511
Page 29
H36PVN Power Vent Indoor Gas Fireplace
Maintenance
Removing the Log Grate:
Step 1 & 2. Figure 20. (Pilot mounting
machine screws).
The H36PVN is supplied with a log Grate that is fastened directly to
the base of the Fireplace. To remove the Grate, to perform certain
Maintenance functions, follow the steps described below:
5
Step 1. CLOSE GAS VALVE AT INCOMING TO FIREPLACE, (By
Qualified Persons ONLY, See 'Before You Start' in the Index).
2
1
Step 3 & 4. Figure 20a. (LH Base
mounting machine screw). Figure
20b. (RH Base mounting machine
screw).
4
Step 2. Remove the two (2) machine screws that hold the Pilot
Assembly in place, Figure 20. (Philips head screwdriver required).
3
Step 5. Figure 20c & 20d. Loosen, and
Remove the Flexible Gas hose (at
fitting), (turn clockwise, left to right)
(3/4" Open end wrench required).
2
1
Figure 20e. (Log Grate Removal Sequence).
Figure 20. (Pilot mounting machine screws).
Step 3 & 4 Remove the two (2) (RH & LH) Base mounting machine
screws, Figure 20a & 20b. (Philips head screwdriver required).
Removing the Refractory:
The H36PVN is supplied three (3) pieces of firebox refractory Lining.
These panels are fastened directly to the interior sides, and back
of the Fireplace firebox with brackets. To remove the brackets and
panels follow the steps described below:
4
3
Figure 20b. (RH Base mounting
machine screw).
Figure 20a. (LH Base mounting
machine screw).
Step 5. Loosen, and Remove the Flexible Gas hose (at fitting),
(turn clockwise, left to right) Figure 20c & 20d. (3/4" Open end
wrench required).
Step 1. Remove the RH-TOP machine screw that hold the Side
Refractory panel in place, then the bottom, Figure 22. (Philips head
screwdriver required).
Step 2. Remove the RH-Refractory panel from the firebox, Figure
22. (Place the Refractory panel somewhere safe where it will not
get chipped or damaged).
Step 3. Follow step1 & 2 to remove the LH-Side Refractory panel,
Figure 22. (Philips head screwdriver required).
Bottom
Brackets
Back-Panel
Top
Brackets
LH-Panel
5
RH-Panel
5
Figure 20c. (Gas fitting).
Figure 20d. (Loosening Gas fitting
on burner).
Figure 22. (Removing Refractory panels).
NOTE: Ensure all 5-steps are complete before removing Log Grate.
(Failing to do so may damage the flexible gas hose, or mounting
hardware of the grate). Figure 14e.
Page 30
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Maintenance
Removing the Stand-off Panels:
Removing the Access Panel:
The H36PVN is supplied two (2) two Stand-off Panels (RH & LH) that
hold the firebox refractory Lining in place. These panels are fastened
directly to the interior sides of the firebox with sheet metal screws. To
remove the panels follow the steps described below:
The H36PVN is supplied one (1) one interior access Panel (RH-side)
that contains the electronics and power control circuits. This panel is
fastened directly to the interior of the firebox with sheet metal screws.
To remove the panel follow the steps below:
Step 1. Remove the RH Refractory Panel as described in Figure 22.
Step 1. Remove the two (2) RH-TOP machine screw that hold
the Side panels in place, then the bottom two (2) machine screws,
Figure 24. (Philips head screwdriver required).
2
Step 2. Remove the RH Refractory Stand-off Panel as described
in Figure 24 & 24a.
Step 3. Having these two steps completed, remove the eight (8)
machine screw that hold the Side panels in place, Figure 26. (Philips
head screwdriver required).
Top 1
Step 4. Slightly tilt panel, and pull out between the grate and firebox
wall, Figure 26a.
Figure 24. (Inset).
3
Power Vent
Control Access
Panel
4
Access Panel
hardware,
7-pcs
Figure 24. (Removing interior stand-off panel hardware).
Step 2. Tilt the panel out from the top, and remove the panel from
the firebox. Pull out of the firebox straight, toward you without hitting
the Grate or panel Retaining brackets, Figure 24a.
Grate
Note: Place the panel somewhere safe where it will not get
damaged.
Side panel
retaining bracket,
4-places
Figure 26. (Removing the panel hardware).
Figure 26a. (Removing the panel from
the firebox).
12d).
Grate
Figure 24a. (Removing interior stand-off panels).
Blk
Step 3. Follow step1 & 2 to remove the LH-Side panel, Figure 24
& 24a. (Philips head screwdriver required).
Wht
12f) .
12).
Figure 26b. (A/C Connections, Gas
module and fireplace chassis). See figure
13, Schematic).
XG0649 - 031511
Figure 26c. (Remote LVT Switch
connection). See figure 13, Schematic).
Page 31
H36PVN Power Vent Indoor Gas Fireplace
Maintenance
Removing the Interior firebox Access Panel:
The H36PVN is supplied one (1) one interior access Panel (LH-side
firebox) that contains the Gas valve, and electronics. This panel is
fastened directly to the interior of the firebox with sheet metal screws.
To remove the panel follow the steps below:
Step 1. Remove the LH Refractory Panel as described in Figure 22.
General
 Have the fireplace and installation inspected yearly. The
inspection must include, but is not limited to, the following:
• A visual check of the entire vent system and termination.
• An inspection of the explosion relief flappers and the door gasketing to ensure a proper seal.
• An inspection of the burner, venturi, and primary air openings.
Step 2. Remove the LH Refractory Stand-off Panel as described in
Figure 24 & 24a.
• An inspection of the gas valve, gas components, and pilot
flame. For your convenience a 1/8" manifold pressure tap is
supplied on the gas valve for a test gauge connection.
Step 3. Once these two steps are complete, remove the eight (8)
machine screw that hold the Side panels in place, Figure 28. (Philips
head screwdriver required).
• Ensure proper log placement as per this manual.
Step 4. Slightly tilt panel, and pull out between the grate and firebox
wall, Figure 28a.
• Inspection of all optional equipment; fans, thermostats, etc.
 For Natural Gas this appliance requires a minimum inlet pressure
of 5.5" W.C. and a manifold pressure of 3.5" W.C.
 For Propane Gas this appliance requires a minimum inlet pressure
of 11" W.C. and a manifold pressure of 10" W.C.
 Always keep the fireplace area clear and free of combustible
materials, as well as gasoline and other flammable vapors and
liquids.
Access Panel
hardware,
7-pcs
 Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any
gas control which has been under water.
Gas Valve
Gas Valve, Control
Access Panel
Cleaning
Grate
Grate
Figure 28. (Removing the panel Figure 28a. (Removing the panel from
the firebox), incoming gas from service
hardware).
and Gas valve.
When the fireplace is first activated, there may be some smoking and
a visible film may be left on the glass. This is a normal condition, and
is the result of burning of protective coatings on new metal.
 Glass must be cleaned periodically to remove any film (which is
a normal by-product of combustion) which may be visible. Film
can easily be removed by removing the door, as shown on Page
23. Handle the door carefully, and clean it with non-abrasive glass
cleaners. One of the most effective products is Kel Kem.
 Silicone seals on inner door during initial firing will "off gas", leaving
a visual deposit of a white substance on combustion chamber walls.
This can easily be removed using normal household products.
 Use a vacuum cleaner or whisk broom to keep the control
compartment, burner, and firebox free from dust and lint. Gas Valve
 Logs may be cleaned periodically with a vacuum to remove soot
or other contaminates.
Blk Wht
Gas valve
Valve
Gas
Electronics
electronics
Figure 28b. (Gas valve and Gas valve
electronic module). See figure 13a,
Schematic).
Page 32
Figure 28c. (Gas valve electronic
module A/C Connection). See figure
13a, Schematic).
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Maintenance
Section:
Troubleshooting: (SIT - IPI Electronic)
1.
1. Locate the lead to the battery backup, (remove)
(Refer to schematic, below)
2.
2. Locate the AC/DC wall transformer, (Unplug connector)
(Refer to schematic, below)
If your fireplace still does not operate correctly, consult your dealer
or the manufacturer.
Replacement Parts
XG0649 - 031511
Part Description
Part Number
Gas Valve - N.G. Manual Hi low
RGC3044
Pilot Assembly - N.G. - Complete
RPA033
Igniter Probe Assembly
RGC3052
Flame sensor rod assembly
RGC3053
Pilot Tubing 18" Length
RPTA03
Control Module
RGC3035
Wiring Harness
RGC3041
DC Adapter
RGC3043
Power Vent Control Box
ECB007
Log Set
RLGSHW42
Page 33
H36PVN Power Vent Indoor Gas Fireplace
Appendix
Appendix A: Power Vent Locations
V
Horizontal
Detail
Vertical Detail
A = clearance to the termination frame above grade, veranda, porch, deck,
or balcony [30 inches (75 cm) minimum]
N = † clearance above paved sidewalk or a paved driveway located on public
property [*7 feet (2.1 m) minimum]
B = clearance to door, or sides and top of window, that may be opened [30
inches (75 cm) minimum for appliances.
P = clearance under veranda, porch, deck, or balcony [30 inches (75
cm) minimum‡ to non-combustibles] [30 inches (75 cm) minimum‡ to
combustibles]
C = clearance to bottom of window that may be opened horizontally [36
inches (92 cm) minimum for appliances.
Q = clearance above a roof [18 inches (46 cm) minimum]
D = no clearance to permanently closed window when installed with approved
glass penetration termination
R = clearance to adjacent walls and neighboring buildings [30 inches (75
cm) minimum]
E = clearance to permanently closed window [30 inches 75 cm recommended
to prevent condensation on window]
S = clearance from corner in recessed location [30 inches (75 cm) minimum]
F = vertical clearance to ventilated soffit located above the termination
within a horizontal distance of [30 inches 75 cm] from the centreline of
the termination [30 inches (75 cm) minimum]
U = minimum width for back wall of recessed location [60 inches (150 cm)
minimum]
G = c l e a r a n c e t o u n v e n t i l a t e d s o f f i t [ 3 0 i n c h e s
(75
cm)
minimum
to
non-combustibles]
[30 inches (75 cm) minimum to combustibles]
H = clearance to outside corner [30 inches (75 cm) minimum]
I = clearance to inside corner [30 inches (75 cm) minimum]
J = * not to be installed above a meter/regulator assembly within
40" (103 cm) horizontally from the centreline of the regulator
K = clearance to service regulator vent outlet [3 feet minimum in the United
States] [*6 feet (1.8 m) minimum in Canada]
L = clearance to non-mechanical air supply inlet to building or the combustion
air inlet to any other appliance [16 inches (41 cm) minimum for appliances
≤100 000 BTU/H (30kW)]
T = maximum depth in recessed location [48 inches (122 cm) minimum]
V = minimum horizontal clearance between the frames of two terminations
that are level, (see applicable Detail).
W = horizontal clearance between the frames of two terminations that are
not level. [30 inches (75 cm) minimum]
a vent shall not terminate directly above a sidewalk or paved driveway
which is located between two single family dwellings and serves both
dwellings
only permitted if veranda, porch, deck, or balcony has an open side that
is equal to or greater than the depth of the enclosed area
*
as specified in CGA B149 Installation Codes. Note: local Codes or
Regulations may require different clearance.
†
‡
M = clearance to mechanical air supply inlet [*6 feet (1.8 m) minimum]
Page 34
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Appendix
Appendix A: Power Vent Locations
EDVRSPV58 Vertical Power Vent Detail
EDVWSPV58 Horizontal Power Vent Detail
Wall
30”Min.
“R”
Wall
Eaves / Overhang
Wall
30”Min.
“F” & “G”
30”Min.
“R”
Top View
“R”
24” (61cm)
Min. “V”
30”Min.
“H” & “I”
30” (75cm)
Min. “V”
Front View
Wall
18”
18”
Min.
Front View
Not Acceptable
Front View
Side View
XG0649 - 031511
Page 35
H36PVN Power Vent Indoor Gas Fireplace
Appendix
Appendix B: Warranty
The Warranty
The Companies warrants the Montigo Gas Appliance to be free from defects in materials and workmanship at the time of manufacture. On the Montigo fireplace,
there is a ten-year warranty on the firebox and its components, a five-year warranty on the main burner and pilot burner, and a one-year warranty on the gas control
valve, fibre logs and Power Vent Module. The Glass, plated / painted finishes, and refractory lining are exempt from the warranty.
Remedy And Exclusions
The coverage of this Warranty is limited to all components of the Gas Appliance manufactured by The Companies.
This Warranty only covers Montigo Gas Appliances installed in the United States or Canada.
If the components of the Gas Appliance covered by this Warranty are found to be defective within the time frame stated (see The Companies right of investigation
outlined below). The Companies will, at its option, replace or repair defective components of the Gas Appliance manufactured by The Companies at no charge,
and will also pay for reasonable labour costs incurred in replacing or repairing components. If repair or replacement is not commercially practical, The Companies
will, at its option, refund the purchase price of the Montigo Gas Appliance.
This Warranty covers only parts and labour as provided above. In no case shall The Companies be responsible for materials, components, or construction which
are not manufactured or supplied by The Companies, or for the labour necessary to install, repair or remove such materials, components or construction. All
replacement or repair components will be shipped F.O.B. the nearest The Companies factory.
Qualifications To The Warranty
The Gas Appliance Warranty outlined above is further subject to the following qualifications:
(1) The Gas Appliance must be installed in accordance with The Companies installation instructions and local building codes. The Warranty on this Montigo
Gas Appliance covers only the component parts manufactured by The Companies. The use of components manufactured by others with this Montigo Gas
Appliance could create serious safety hazards, may result in the denial of certification by recognized national safety agencies, and could be in violation of
local building codes. This warranty does not cover any damages occurring from the use of any components not manufactured or supplied by The Companies
(2) The Montigo Gas Appliance must be subjected to normal use. The Gas Appliances are designed to burn gas only. Burning conventional fireplace fuels such
as wood, coal or any other solid fuel will cause damage to the Gas Appliance, will produce excessive temperatures and will result in a fire hazard.
Limitations On Liability
It is expressly agreed and understood that The Companies sole obligation, and purchaser's exclusive remedy under this Warranty, under any other warranty,
expressed or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above.
In no event shall The Companies be responsible for any incidental or consequential damages caused by defects in its products, whether such damage occurs
or is discovered before or after replacement or repair, and whether or not such damage is caused by The Companies negligence. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. The duration of any implied warranty
with respect to this Montigo Gas Appliance is limited to the duration of the foregoing warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above may not apply to you.
Investigation Of Claims Against Warranty
The Companies reserves the right to investigate any and all claims against this Warranty and to decide upon method of settlement.
The Companies Are Not Responsible For Work Done Without Written Consent
The Companies shall in no event be responsible for any warranty work done without first obtaining The Companies written consent.
Dealers Have No Authority To Alter This Warranty
The Companies employees and dealers have no authority to make any warranties nor to authorize any remedies in addition to or inconsistent with those stated above.
How To Register A Claim Against Warranty
In order for any claim under this Warranty to be valid, The Companies must be notified of the claimed defect in writing or by telephone, as soon as reasonably
possible after the defect is discovered. Claims against this Warranty in writing should include the date of installation, and a description of the defect.
Other Rights
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
NOTE:
The Companies as stated above refer to - Canadian Heating Products Inc. and/or Montigo Del Ray Corp.
Canadian Heating Products Inc. and/or Montigo DelRay Corp. reserves the right to make changes at any time, without notice, in design, materials,
specifications, prices and also to discontinue colors, styles and products.
Page 36
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Appendix
Amendment
Appendix C: State of Massachusetts
(Gas Fireplace / Equipment sold in the State of Massachusetts)
5.08: Modifications to NFPA-54, Chapter 10
(1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as follows:
Existing chimneys shall be permitted to have their use continued when a gas conversion burner is installed, and shall be equipped with a manually reset device
that will automatically shut off the gas to the burner in the event of a sustained back-draft.
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes,
including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in
the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon
monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled
equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon
monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days
to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm
shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet
above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print
size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless,
upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the
Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes. (c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions
provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”,
the following requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for
venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
(3) After NFPA-54 section 10.10.4.2 add a new section 10.10.4.3 as follows:
When more than four gas appliances are to be vented through a common gas vent or common horizontal vent manifold, a plan of the proposed vent installation
shall be submitted to the Inspector and the serving gas supplier for review and approval.
Extraction from: Massachusets Rules and Regulations
5.00: Amendments To 2002 Edition Of ANSI Z223.1-NFPA-54
XG0649 - 031511
Page 37
H36PVN Power Vent Indoor Gas Fireplace
Notes
Page 38
XG0649 - 031511
H36PVN Power Vent Indoor Gas Fireplace
Notes
XG0649 - 031511
Page 39
H36 PV
Power Vented Residential Gas Fireplace
Ferndale, Washington
TF: 1.800.789.6236
FX: 1.866.3000.0927
XG0649 - 031511
Langley, British Columbia
TF: 1.800.378.3115
FX: 1.604.607.6462
Download PDF