Stanton C402 Manual

Stanton C402 Manual
C.402
/
USER MANUAL
IMPORTANT SAFETY PREC AUTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15. Servicing - The user should not attempt any service to the appliance
beyond that described in the operating instructions. All other servicing
should be referred to qualified service personnel..
16. Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product
should not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is the manufacturers instructions have
been adhered to.
17. Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
18. Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any mounting of the product
should follow the manufacturer s instructions, and should use
amounting accessory recommended by the manufacturer.
19. Lightning - For added protection fo r this product during a lightning
storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.
20. Replacement Parts - When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
21. Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
22. This product is in compliance with EUWEEE
regulations. Disposal of end of life product should not
be treated as municipal waste. Please refer to your
local regulations for instructions on proper disposal of
this product.
23. Carts and Stands - The appliance should be used only
with a cart or stand that is recommended by the
manufacturer. An appliance and cart combination
should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the appliance
and cart combination to overturn.
24. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Read Instructions - All the safety and operating instructions should
be read before this product is operated.
Retain Instructions - The safety and operating instructions should be
retained for future reference.
Heed Warnings - All warnings on the appliance and in the operating
instructions should be adhered to.
Follow Instructions - All operating and use instructions should be
followed.
Water and Moisture - The appliance should not be used near water
- for example, near a bathtub, washbowl, kitchen sink, laundry tub, in
a wet basement, or near a swimming pool, and the like.
Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
Heat - Appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
Power Sources - This product should be operated only from the type of
power source indicated on the rating label. If you are not sure of the
type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery
power, or other sources, refer the operating instructions.
Grounding or Polarization - This product may be equipped with a
polarized alternating current li ne plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
Power-Cord Protection - Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to the cord in
correspondence of plugs, convenience receptacles, and the point
where they exit from the appliance.
Cleaning - The appliance should be cleaned only as recommended by
the manufacturer. Clean by wiping with a cloth slightly damp with
water. Avoid getting water inside the appliance.
Non-use Periods - The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of time.
Object and Liquid Entry - Care should be taken so that objects do
not fall and liquids are not spilled into the enclosure through openings.
Damage Requiring Service - The appliance should be serviced by
qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a
marked change in performance; or
E. The appliance has been dropped, or the enclosure damage.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock, do not remove an y
cover. No user-serviceable parts inside. Refer servicing to qualified
service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use to the
presence of un-insulated "dangerous voltage” within the products enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of important
operation and maintenance (servicing) instructions in the literature accompanying this appliance.
CAUTION: To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet
unless the blades can be fully inserted to prevent blade exposure.
1
IMPORTANT TO SAFETY
WARNING:
• TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
USE THIS PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PRES ENT
BLADE EXPOSURE.
• TO PREVENT FIRE OR SHOCK HAZARD. NO NOT
EXPOSE THIS APPLIANCE TO RAIN OR NOISTURE.
• TO PREVENT ELECTRICAL SHOCK, MATCH WIDE
BLADE PLUG TO WIDE SLOT AND FULLY INSERT.
CAUTION:
1. Handle the power supply cord carefully
Do not damage or deform the power supply cord. If it is
damaged or deformed, it may cause electric shock or
malfunction when used. When removing from wall outlet,
be sure to remove by holding the plug attachment and
not by pulling the cord.
•FOR U.S.A. & CANADA MODEL ONLY
CAUTION
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
NOTE:
This CD player uses a semiconductor laser. To allo w you to
enjoy music at a stable operation, it is recommended to use
O
O
O
O
this in a room of 5 C 41 F - 35 C 95 F.
2. In order to prevent electric shock, do not open the
top cover. If a problem occurs, contact your dealer.
3. Do not place metal objects or spill liquid inside the
CD player. Electric shock or malfunction may result.
Please, record and retain the Model name and serial
number of your set shown on the rating label.
Model No. ___________ Serial No. ___________
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER
(OR BAC K) . NO USERSERVICEABLE PARTS I NSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation po
within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CLASS 1 LABEL
RATING LABEL
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR
REFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
THE COMPACT DISC PLAYER SHOULD NOT BE
ADJUSTED OR REPAIRED BY ANYONE EXCEPT
PROPERLY QUALIFIED SERVICE PERSONNEL.
DOUBLE INSULATED - WHEN SERVICING, USE ONLY
IDENTICAL REPLACEMENT PARTS.
NOTE:
This unit may cause interference to radio and television
reception.
• Line Voltage Selection (for multiple voltage
model only)
The desired voltage may be set with the
VOLTAGE SELECTOR switch on the rear
panel, using a screwdriver.
Do not twist the VOLTAGE SELECTOR
switch with excessive force as this may
cause damage.
If the VOLTAGE SELECTOR switch does not move
smoothly, please contact a qualified serviceman.
2
NOTE ON USE
•
•
•
•
•
•
•
•
•
•
Allow for sufficient heat dispersion when installed in a rack.
Handle the power cord carefully.
Hold the plug when unplugging the cord.
Keep the set free from moisture, water, and dust.
Unplug the power cord when not using the set for long periods of time.
Do not obstruct the ventilation holes. (For sets with ventilation holes.)
Do not place foreign objects in the set.
Do not let insecticides, benzene, and thinner come in contact with the set.
Never disassemble or modify the set in any way.
For 120 volt use in USA, USA nema style 120 volt plug. For other countries, use proper plug for the local outlet.
MAIN FEATURES
(1)
(2)
(3)
(4)
(5)
(6)
8 times oversampling, 1 bit D/A converter.
4 different scan speeds.
Frame search.
Auto cue.
Pitch display.
Digital output.
MAIN UNIT
1
2
DIGITAL OUT SOCKET
AC IN
VOLTAGE SELECTOR (Just for Dual Voltage only)
1
4
5
6
(1)
(3)
(5)
3
(2)
BALANCED OUTPUT L/R
(4) REMOTE START
(6)
AUDIO OUTPUT L AND R
3
2
4
5 6 7 8 9 10 11 12
13
/
21
(1) POWER BUTTON
(5) TIME
(9) RELOOP
(13)PITCH SLIDER
(17)PLAY/PAUSE
(21)JOG WHEEL
(2) DISC HOLDER
(6)
TRACK BACKWARD
(10)
F.BACKWARD
(14) PITCH LOCK
(18) LOOP OUT
(3)
(7)
(11)
(15)
(19)
3
20 19 18 17 16 15 14
OPEN/CLOSE
+10/ FOLDER
F.FORWARD
PITCH +/CUE
(4)
(8)
(12)
(16)
(20)
SGL/CTN
TRACK FORWARD
LCD
PITCH RANGE
LOOP IN
MAIN FEATURES
LCD
1
2 39 4 59
15 14 13
12 17 16 12
7 8 8 99
6
11
12
10
(1) PLAY/PAUSE INDICATOR
(4) SINGLE INDICATOR
(7) LOOP INDICATOR
(2) CUE INDICATOR
(5) MP3 INDICATOR
(8) RELOOP INDICATOR
(3) FOLDER/TRACK INDICATOR
(6) TIME BAR INDICATOR
(9) PITCH INDICATOR
(10) PITCH METER
(11) TIME DISPLAY
(12) CHARACTER DISPLAY
(13) ELAPSED INDICATOR
(16) TRACK INDICATOR
(14) REMAIN INDICATOR
(17) AUTO CUE
(15) TOTAL REMAIN INDICATOR
PREPARATIONS
1. Checking the Contents
Check that the carton contains the following items:
1) Main unit 2) Pair of RCA cables 3) Operating instructions (this booklet)
4) Power cord
NAMES AND FUNCTIONS
Main Unit
(1) DIGITAL OUT SOCKET
Coaxial (S/P DIF) digital output for use with audio
devices equipped with coaxial (S/P DIF) digital input
such as digital mixing consoles and computer audio
cards.
(4) REMOTE START
The player is paused when a Remote Switch is pressed
once; when touched again, it starts playing.
(5) VOLTAGE SELECTOR (Just for Dual Voltage only)
Select 115V or 230V according to the local voltage.
(2) BALANCED OUTPUT
Connect other appliances with balanced output easily.
(6) AUDIO OUT
The audio signals from each player are output from
these jacks.
(3) AC IN
Plug in the power supply cable here.
4
NAMES AND FUNCTIONS
Main Unit
(1) POWER (Power ON/OFF Switch)
When the POWER switch is pressed, the power turns
on.
(13)PITCH SLIDER
Use the slider to adjust the CD pitch. Slide up to
decrease the pitch, down to increase the pitch.
(2) DISC HOLDER
Place the discs in the holder. Press the OPEN/CLOSE
button to open and close the disc holder.
(14)PITCH LOCK
Use this button to enable or disable BPM
adjustment with the pitch sliders. BPM adjustment with
the pitch sliders is disabled when the PITCH LED lights.
(3) OPEN/CLOSE
Press this button to open and close the disc holder. The
disc holder cannot be opened during playback, so stop
playback before pressing the button.
(15)PITCH +/- BUTTON
+ The CD speeds up while this button is pressed.
Release the button to return to the original BPM.
- The CD slows down while this button is pressed.
Release the button to return to the original BPM.
(4) SGL/CTN (Single/Continuous Button)
Press this button to switch between single and continuous
play modes. SINGLE mode is indicated by the
SINGLE indicator on the LCD.
(16)PITCH RANGE
Choose from pitch percentages of 4%, 8% and 16%.
(5) TIME (Time Button)
Press this button to switch the time display among the
elapsed time and remaining time and total remaining time
of the disc.
(17)PLAY/PAUSE
Use this button to start playback. Press once to start
playback, once again to set the pause mode, and once
more to resume playback.
(6)
(18)LOOP OUT
TRACK BACKWARD
Use this button to go back to the beginning of the
current track or select a previous track for playing.
(7) +10/
Used for setting the end loop point and releasing the loop
action.
(19)CUE (Cue Button)
Press the CUE button during playback to return to the
position at which playback started.
FOLDER
CD mode, use this button to skip ahead 10 tracks.
Mp3 mode, press this button to select next folder.
(8)
(20)LOOP IN
Used for setting a start loop point and releasing the
loop action.
TRACK FORWARD
Use this button to skip to the next CD track.
(9) RELOOP
Depending on mode, as explained further, this button is
used for either repeating a previously set loop or
seamlessly stuttering on the last set cue point.
(21)JOG WHEEL(JOG dial)
When the dial is turned during CD pause, the point at
which the sound is being produced moves by a number
of frames corresponding to the number of clicks.
Clockwise moves the point forward, counterclockwise
moves the point backward.
(10),(11)
F.FORWARD/F.BACKWARD
Press these buttons to perform the scan function during
pause mode or during play mode.
(12) LCD
5
NAMES AND FUNCTIONS
LCD
(1) PLAY / PAUSE INDICATOR
When the unit is in play mode the “PLAY”
indicator will glow, when the drive is in pause
mode the “PAUSE” indicator will glow.
(10) PITCH METER
Shows the percentage change in pitch of the song.
The meter will display the pitch percentage
applied by the PITCH SLIDER.
(2) CUE INDICATOR
This indicator will glow when the unit is in CUE
mode and will flash every time a new CUE
POINT is set.
(11) TIME DISPLAY
This displays the Minutes, Seconds, and
Frames. The meter will display either the
elapsed time, or remaining time of a track.
(3) FOLDER/TRACK INDICATOR
This indicator shows you if you are looking at the
track number or the folder number.
(12) CHARACTER DISPLAY
This will display the name of the file, artist, and
title when a disc is loaded.
(13) ELAPSED INDICATOR
When the ELAPSED indicator is visible, this
indicates that the Time Display is showing elapsed
track time.
(4) SINGLE INDICATOR
This indicates that the CD drive is in single play
mode. The track will play once and return to CUE
mode. If the single indicator is not on, the unit is
in continuous mode and the drive will play all
the remaining tracks on the disc until you stop
play or power is interrupted.
(14) REMAIN INDICATOR
When the REMAIN indicator is visible, this
indicates that the Time Display is showing remaining
track time.
(5) MP3 INDICATOR
This will indicate that a Mp3 disc is loaded in the
drive.
(15) TOTAL REMAIN INDICATOR
When TOTAL and REMAIN are visible, this
indicates that the Time Display is showing total
remaining disc time.
(6) TIME BAR INDICATOR
This bar gives a visual approximation of a track's
or disc's remaining time. This bar will begin to
flash when a CD is ending.
(16) TRACK INDICATOR
This 3-digit indicator displays the current track. The
number displayed in the track indicator is a direct
reference to a track being selected or a track in
play, pause, or cue mode.
(7) LOOP INDICATOR
Appears when the CD is repeating a particular
area with the music on the CD.
(17) AUTO CUE
This will indicate if the Auto Cue is on or off.
Press and hold the SGL/CTN for 1 sec. to turn
the Auto Cue function on and off.
(8) RELOOP INDICATOR
Appears when the CD has had a loop set
previously and can go back to loop again.
(9) PITCH INDICATOR
Indicator will light up when the Pitch is activated.
6
OPERATIONS
1. Opening and Closing the Disc Holder
Turn the unit power on. Press the OPEN/CLOSE button to open the disc holder.
The disc holder cannot be opened during playback to prevent playback from being interrupted if the OPEN/CLOSE
button is pressed accidentally. Stop the playback first, then press the OPEN/CLOSE button.
2. Loading discs
Hold the disc by the edges and place it in the disc holder, then press the
OPEN/CLOSE button again to close the disc holder. The unit will show the total
track number and the total playing time for about 2 seconds then enter the cue
condition. The cue point will be set to the music starting point of the first track
automatically.
CAUTION:
Do not place any foreign objects in the disc holder, and do not place more than one disc in the disc holder at a time.
Do not push the disc holder in manually when the power is off, as this may result in malfunction and damages the player.
3. Selecting Tracks
Press the TRACK button once to move to next higher or lower track.
Hold the TRACK button to change tracks continuously at a higher speed.
When a new track is selected during playback, playback begins as soon as the skip search operation is completed.
If the TRACK
button is pressed while at the last track, the first track is selected. In the same way, if the TRACK
button is pressed while at the first track, the last track is selected.
4. Starting Playback
Press the PLAY/PAUSE button during the pause or cue condition to start playback. The PLAY indicator will light.
The point at which playback starts is automatically stored in the memory as the cue point. The pickup then returns to
the cue point when the CUE button is pressed. (Back Cue)
Figure 4-1
5A. Stopping Playback
There are two ways to stop playback.
1. Press the PLAY/PAUSE button during playback to pause at that point.
2. Press the CUE button during playback to return to the cue point and enter pause condition.(Back Cue)
CUE
Figure 5-1
7
OPERATIONS
5B. Pausing
˙ Press the PLAY/PAUSE button to switch between play and pause.
˙ The play indicator flashes when the pause mode is set.
˙ Figure 5-2 shows the relationship between play and pause.
2
4
6
3
7
1
1)
2)
3)
4)
5
The player has completed the cue or pause operation
and is waiting for the play start command.
PLAY/PAUSE button is presse d and player enters play
mode.
Playing.
The PLAY/PAUSE button is presse d and the unit enters
Figure 5-2
5)
6)
7)
pause mode.
Pausing.
Playback resumes when the PLAY/PAUSE butt on is
pressed again.
Playing.
6. Cueing
˙ "Cueing" is the process of preparing for playback.
˙ Press the CUE button, the player will enter cue mode. The playback returns to the cue point and the player enters
the pause condition. The cue indicator lights up and the play indicator flashes. When the PLAY/PAUSE button is
pressed, playback starts from the cue point.
˙ When the track search operation is completed after pressing the SKIP buttons, the player automatically finds the
position at which the sound starts and cues there(Auto Cue).
˙ If the CUE button is pressed after the search operation or the scanning operation, playback returns to the cue point
and enter pause condition.
˙ Figure 6-1 shows the relationship between the play and back cue operations.
2
8
2
3
1
9
4
6
8
3
7
1
5
9
Figure 6-1
The player has completed the cue or pause operation
pressed again.
5) Pausing.
and is waiting for the play start command.
2) When the PLAY/PAUSE button is presse d, playback
6) The PLAY/PAUSE button is pressed again;
7) Playing.
starts and the cue point is stored in the memory.
8) Press the CUE button.
3) Playing.
9) The pickup returns to the cue point.(Back Cue)
4) The pause mode is set when the PLAY/PAUSE b utton is
˙ Cue point setting:
When play starts from pause by pressing the IN button or by using Scanning or Frame Search, or if you skip to a new
track by using the skip button, the begin play point will be set to the new cue point.
When a new cue point is set, the cue indicator lights by flashing for about 1 second.
NOTE: During cue mode, if the CUE button is pressed and held, playback will start from the cue point. When the button
is released, the player will return to the cue mode automatically. This allows you to check the cue point.
1)
7. Jog Wheel - The jog wheel serves two functions depending on the current operating mode:
The jog wheel will act as a slow frame search control when the unit is in pause or cue mode allowing you to set a
specific cue point or find a particular starting point.
The wheel also works as a momentary pitch bend during playback. Turning the wheel clockwise will increase the pitch
percentage up to +16%, and turning the wheel in the counterclockwise direction will decrease the pitch
percentage up to -16%. The pitch bend will be determined on how fast you turn the wheel.
8
OPERATIONS
8. Scanning (Fast forward/Fast backward)
or
button is pressed.
Scanning is a function for moving quickly forward or backward in the track when the
The scanning speed depends on how long you hold the button.
Press and hold the
or
to begin scanning. The disc moves rapidly forward or backward and the sound is
played. The current scan point is indicated on the LCD.
Press and hold the
to scan in the forward scanning,
to scan in the reverse scanning.
9. Time display
MP3 MODE
Press TIME button to select time display MP3 mode:
Elapsed time of a track.
(2) Remaining time of a track.
(1)
ELAPSED
REMAIN
Figure 9-1
CD MODE
Press this button to select the time display .
It switches between the elapsed time and remaining time and total remaining time of the disc.
ELAPSED
TOTAL
REMAIN
REMAIN
Figure 9-2
10. Matching the Beats Per Minute (BPM)
There are three tools available for matching the BPM :
(1) Use the pitch slider to adjust the BPM statically.
(2) Use the PITCH BEND buttons to change the BPM temporarily.
(3) Use the JOG WHEEL to change the BPM temporarily.
1) Pitch Slider
(1) To adjust the BPM by sliding the pitch slider up or down, you must first press the PITCH button to turn on the
Pitch Slider.
(2)
Slide the pitch slider up to decrease BPM, or down to increase BPM. The adjustment range is switchable from +/4%,+/-8% to +/-16%.
2) Pitch Bending
The BPM increases or decreases respectively while the PITCH BEND+ or PITCH BEND- button is pressed.
The BPM increase depends on how long you hold the button. If you hold the button for about 1/2 second, the BPM will
go either to +16% for PITCH BEND+ or -16% for PITCH BEND-. If you tap the button, the BPM will only change a little
so you can change the beat slightly without audible changes in the music.
The CD will return to the tempo indicated by the Pitch slider when you let go of the PITCH BEND + or - button.
9
BEFORE SWITCHING OFF THE POWER
CAUTION:
Do not forcibly close the disc holder when the power is off.
Do not switch off the power when the disc holder is open.
To avoid damage, please don’t switch the power until the
disc holder has been closed with the OPEN/CLOSE button
and the LCD displays "no disc”or "time code” shows.
COMPACT DISCS
1. Precautions on handling compact discs
˙ Do not allow fingerprints, oil or dust to get on the surface
of the disc.
If the disc is dirty, wipe it off with a soft dry cloth.
˙ Do not use benzene, thinner, water, record spray,
electrostatic-proof chemicals, or silicone-treated cloths to
clean discs.
˙ Always handle discs carefully to prevent damaging the
surface; in particular when removing a disc from its case
or returning it.
˙ Do not bend the disc.
˙ Do not apply heat.
˙ Do not enlarge the hole in the center of the disc.
˙ Do not write on the label (printed side) with a hard-tipped
implement such as a pencil or ball point pen.
˙ Condensation will form if a disc is brought into a warm
area from a colder one, such as outdoors in winter. Do
not attempt to dry the disc with a hair dryer, etc.
2. Precaution on storage
˙ After playing a disc, always unload it from the
player.
˙ Always store the disc in the jewel case protect from
dirt or damage.
˙ Do not place discs in the following areas:
(1) Areas exposed to directs sunlight for a considerable time.
(2) Areas subject to accumulation of dust or high humidity.
(3) Areas affected by heat from indoor heaters, etc.
SPECIFIC ATIONS
GENERAL
Dimensions:
Weight:
Power supply:
Power consumption:
482(W) x 88.8(H) x 266(D) mm
19"(W) x 3 1/2"(H) x 10 1/2"(D)
5.5 kgs / 12.1 lbs
Dual Voltage:
AC 115/230V, 50/60Hz
Single Voltage:
AC 100V, 50/60Hz (For Japan)
AC 110V, 60Hz (For Taiwan)
AC 120V, 60Hz (For U.S.A.,Canada,Mexico)
AC 220V, 50Hz (For United Arab Emirates,Chile,Aegentina)
AC 220V, 60Hz (For Philippines)
AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel)
AC 240V, 50Hz (For Australia,U.K)
20W
10
WARRANTY & RETURN POLICY
WARRANTY & RETURN POLICY
Warranty
Through Stantons authorized dealers around the World, Stanton, or one of Stantons authorized distributors outside the U.S., will, without charge, repair
or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective
in material or workmanship for a period of one (1) year following the date of original purchase. Exceptions to this warranty are as noted below:
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier of either thirty (30) days following the date of original
purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and Switches - 10,000.
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made necessary by reason of mi use, alteration, normal wear, or accident are not covered under this warranty.
Returns
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring warranty repair or replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from whom the merchandise was purchased and in the
same country where the merchandise was purchased. For purposes of purchases made via the Internet, the merchandise must be returned to the authorized Stanton dealer in the country where the authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton
dealer in the country where the purchaser is located or the country in which the merchandise was received. Any returns to a non-authorized dealer or to
an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth above will void this warranty.
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and follow such authorized
Stanton dealers return policy.
Stanton assumes no risk and shall be subject to no liability for damage or loss resulting from the specific use or application made of the merchandise.
Stantons liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party, or product liability, and relating
to the merchandise shall not exceed the price received by Stanton from our purchase of such merchandise. In no event will Stanton be liable for any
special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence
of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of
merchantability or fitness for a particular purpose.
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation from state to state and
country to country.
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein.
Please register your product online at www.stantondj.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement