Master-force | 252-8020 | Operator`s manual | Master-force 252-8020 Operator`s manual

12.0-Volt Lithium-Ion
Power Source
241-0318
OPERATOR’S MANUAL
CAUTION: To Reduce The Risk Of Injury, User Must Read
And Understand Operator’s Manual. Save These Instructions
For Future Reference.
Page 1
table of contents
Safety Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
Overview / Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9
safety symbols
Some of these following symbols may be used on this tool. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
Symbol
Name
Designation / Explanation
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
W
Watts
Power
∿
Alternating current
Type of current
�
Direct current
Type of characteristic of current
no
No-load speed
Rotational speed at no load
Class II construction
Double insulated construction
Per minute
Revolutions, strokes, surface speed
orbits, etc., per minute
.../min
Wear safety goggles
WARNING: The operation of any
power tool can result in foreign objects
being thrown into your eyes, which can
result in severe eye damage. Before
beginning power tool operation, always
wear safety goggles or safety glasses
with side shields and a full-face shield
when needed. We recommend a Wide
Vision Safety Mask for use over eyeglasses or standard safety glasses with
side shields. Always use eye protection
which is marked to comply with
ANSI Z87.1.
WARNING: To ensure safety and reliability, all repairs should be performed by a
qualified service technician.
Page 2
safety INSTRUCTIONS
The purpose of safety symbols is to attract your attention to possible dangers. The
safety symbols and the explanations with them deserve your careful attention and
understanding. The symbol warnings do not, by themselves, eliminate any danger. The
instructions and warnings they give are no substitutes for proper accident prevention
measures.
WARNING: Be sure to read and understand all safety instructions in this manual,
including all safety alert symbols such as “DANGER,” ”WARNING,” and “CAUTION”
before using this auto hammer . Failure to following all instructions listed below may
result in electric shock, fire, and/or serious personal injury.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION.
May be used in conjunction with other symbols or pictographs.
DANGER: Indicates an imminently hazardous situation, which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided,
could result in minor or moderate injury.
NOTICE: (Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SAVE THESE INSTRUCTIONS!
Page 3
safety INSTRUCTIONS
WARNING:
Read all safety
warnings and instructions!
Failure to follow the warnings and
instructions may result in electric shock,
fire and/or serious personal injury. Save
these instructions – This operator’s manual
contains important safety and operating
instructions for the MASTERFORCE 12V
Power Source. Before using this Power
Source, read this operator’s manual, your
battery pack and charger operator’s
manuals, and all labels on the battery
pack, charger and Power Source.
WARNING: Risk of fire and electric
shock. Dry location use only. Do not
expose to rain. Risk of injury.
Work area safety
1. Avoid dangerous environments. Do not
use outdoors in rain, snow, damp or wet
locations.
2. Do not use in the explosive atmospheres
(in the presence of gaseous fumes, dust or
flammable materials), because sparks may
be generated when inserting or removing
the battery pack, possibly causing fire.
Electrical safety
1. Do not use an extension cord with the
appliance. Using an extension cord could
result in the risk of fire and electrical shock.
Personal safety
3. Stay alert, watch what you are doing
and use common sense when operating
this Power Source. Do not use while you
are tired or under the influence of drugs,
alcohol or medication. A moment of
inattention may result in serious personal
injury.
use and care
1. Disconnect plugs from the Power
Source and remove the battery pack before
storing it. Such preventive safety measures
reduce the risk of starting the appliance
accidentally.
2. Store an idle Power Source out of the
reach of children and do not allow persons
unfamiliar with the power source or
instructions to operate it. The Power Source
is dangerous in the hands of untrained
users.
3. Maintain the Power Source. Check for
misalignment, breakage of parts and any
other condition that may affect the Power
Source operation. If damaged, have the
Power Source repaired before use. Use
the Power Source in accordance with
these instructions, taking into account the
working conditions and the work to be
performed. Use of the Power Source for
operations different from those intended
could result in a hazardous situation.
4. Keep Power Source away from other
metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects
that can make a connection from one
terminal to another. Shorting the terminals
together may cause burns or a fire.
1. Follow the manufacturer’s instructions
regarding operation and power for this
Power Source. Use of the Power Source
other than described in this manual could
result in a hazardous situation.
2. Use the correct appliance for the
application.
Page 4
safety INSTRUCTIONS
Battery tool use and care
Service
1. Your Power Source is rated for 12 V DC
only. Use only appropriate Masterforce
battery packs (252-8016). Use of any other battery pack may create a risk of injury
and fire.
1. Do
not
disassemble.
Incorrect
reassembly may result in the risk of
electric shock or fire.
2. Recharge only with the charger
specified in the table below. A charger that
is suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
3. Use only with the battery and chargers
listed:
Battery pack
Charger
252-8016
252-8020
4. To reduce the risk of electric shock,
always remove battery pack before cleaning
or maintenance.
5. The battery used in this device may
present a risk of fire or chemical burn if
mistreated. Do not disassemble, heat above
120° F (50° C), or incinerate.
6. Dispose of used battery promptly. Keep
away from children. Do not disassemble
and do not dispose of in fire.
Page 5
2. Store in a cool, dry place. Do not store
where temperatures may exceed 120° F
(50° C) such as in direct sunlight, a vehicle
or metal building during the summer.
3. Maintain labels and nameplates. These
carry important information.
4. Follow instructions in the Maintenance
section of this manual. Use of unauthorized
parts or failure to follow Maintenance
instructions may create a risk of shock or
injury.
overview
FIG. 1
Fuel Gauge
5V USB
receptical
12V DC
receptical
Access door
• F
uel gauge: Green, and red LED lights
indicate the amount of charge remaining.
• 5
V DC USB port: power for 5V appliances
with working current less than 1.5A
• 12V DC port: power for 12V automotive
appliances with working current less
than 3A.
• Both ports can power for smarts phones,
digital cameras, MP3 players, navigator,
etc.
• Access door: protects the ports from dirt
and short-circuit.
Specifications
Input
12V DC
DC Output
12V DC, 3A
USB Output
5V DC, 1.5A
Power Source Weight (without battery)
Optimum Charging Temperature
4.76 oz.
50° F (10° C) -104° F (40° C)
Page 6
assembly
UNPACKING
WARNING:
If any part is broken or
missing, DO NOT attempt to attach the
battery or operate the Power Source until
the broken or missing part is replaced.
Failure to do so could result in possible
serious injury.
WARNING:
Use only with the
specified battery and charger. For specific
charging instructions, read the operator’s
manual supplied with your charger and
battery.
WARNING: Do not attempt to
modify this Power Source or create
accessories not recommended for use
with this Power Source. Any such
alteration or modification is misuse and
could result in a hazardous condition
leading to possible serious injury. To
prevent accidental starting that could
cause serious personal injury, always
remove the battery pack from the Power
Source when assembling parts.
This product has been shipped completely
assembled.
1. Carefully remove the Power Source
from the box.
2. Inspect the Power Source carefully to
make sure no breakage or damage
occurred during shipping.
3. Do not discard the packing material
until you have carefully inspected and
satisfactorily operated the tool.
PACKING LIST
12.0-Volt Lithium-Ion power source and
Operator’s Manual
operation
Always remove the battery pack before
changing or removing accessories. Only
use accessories specifically recommended
for this tool. Others may be hazardous.
FIG. 2
Remove
Inserting/Removing the
Battery (Fig. 2)
1. To insert the battery, align the raised
ribs on the battery pack with the grooves
in the Power Source, and then attach the
battery pack to the Power Source.
2. To remove the battery, depress the
battery release buttons located on the both
sides of the battery pack to release the
battery pack. Pull the battery pack out and
remove it from the Power Source.
Page 7
Insert
operation
Fuel Gauge
To indicate the battery-pack charge level, after inserting the battery pack into the
power source, the Fuel Gauge will light up for 5-6 seconds. The functions of Fuel Gauge are
listed:
LED INDICATOR
ON WORKING
LOW BATTERY
SLOW FLASHINGOVERLOADED/
DEFECTIVE DEVICE
RAPID FLASHINGHI/LO TEMP.
RED LED
GREEN LED
MEANING
ON
Power Source is providing power to
device(s).
ON
OFF
Battery charge is below 20%
capacity (Battery pack will turn off
after depleted and LED indicator will
go off).
Slow flashing
at 1 Hz
OFF
Power source is overloaded or
defective.
Rapid
flashing at
2 Hz
OFF
The Power Source is not operating
with the optimum temperature range
of 50°F (10°C) to 104°F (40°C).
OFF
Using the Power Source
FIG. 3
1. Open the access door and plug in a 12 V
Automotive or 5 V USB powered appliance,
and then install the battery (Fig. 3).
2. If the appliance draws more than
the rated output of the port, the Power
Source will shut off all the outlets to protect
the battery pack and the Fuel Gauge will
flash red slowly. To restart the power source,
remove and reinstall the battery pack. Use
only appliances rated within the output
specifications for the port.
Page 8
Maintenance
WARNING: To avoid serious
personal injury, always remove the battery
pack from the Power Source when
cleaning or performing any maintenance.
Never disassemble the power source,
battery pack or charger.
WARNING: Avoid using solvents
when cleaning plastic parts. Most plastics
are susceptible to damage from various
types of commercial solvents and may be
damaged by their use. Use clean cloths to
remove dirt, dust, oil, grease, etc.
WARNING: To reduce the risk of
personal injury and damage, never immerse
your tool, battery pack or charger in liquid
or allow a liquid to flow inside them.
WARNING: When servicing, use
only identical replacement parts. Use of any
other parts may create a hazard or cause
product damage. To ensure safety and
reliability, all repairs should be performed
by a qualified service technician.
troubleshooting
PROBLEM
CAUSE
SOLUTION
The Fuel Gauge is not
ON when a battery
pack has been
inserted.
The battery pack
charge is fully
depleted.
Charge the battery pack following the
instructions for your charger and
battery pack.
Weak contacts.
Check the contacts of the Power
Source; make sure they are clean and
not damaged.
The Power Source
cannot power an
appliance and the Fuel
Gauge flashes in red.
The appliance draws
more than the rated
output of the port.
Remove the appliance from the port;
remove and reinstall the battery pack
to restart the Power Source. Make
sure the working current for the
appliance is not greater than the rated
output of the port.
The output port is under
short circuit protection.
Remove the battery pack, check and
make sure no metal or debris is inside
the ports.
The battery pack is
under high
temperature protection.
Remove the appliance and battery
pack from the Power source, cool the
battery pack until the temperature
drops to 158° F (70° C).
Page 9
notes
Page 10
notes
Page 11
notes
Page 12
notes
Page 13
12.0-Volt Lithium-ion Power Source
WARRANTY
90-DAY MONEY BACK GUARANTEE:
This MASTERFORCE® brand power tool carries our 90-DAY Money Back
Guarantee. If you are not completely satisfied with your MASTERFORCE® brand
power tool for any reason within ninety (90) days from the date of purchase, return
the tool with your original receipt to any MENARDS® retail store, and we will provide
you a refund – no questions asked.
3-YEAR LIMITED WARRANTY:
This MASTERFORCE® brand power tool carries our famous No Hassle 3-Year
Limited Warranty to the original purchaser.
If, during normal use, this
MASTERFORCE® power tool breaks or fails due to a defect in material or
workmanship within three (3) years from the date of original purchase, simply bring
this tool with the original sales receipt back to your nearest MENARDS® retail store.
At its discretion, MASTERFORCE® agrees to have the tool or any defective part(s)
repaired or replaced with the same or similar MASTERFORCE® product or part
free of charge, within the stated warranty period, when returned by the original
purchaser with original sales receipt. Not withstanding the foregoing, this limited
warranty does not cover any damage that has resulted from abuse or misuse of
the Merchandise. This warranty: (1) excludes expendable parts including but not
limited to blades, brushes, belts, bits, light bulbs, and/or batteries; (2) shall be void
if this tool is used for commercial and/or rental purposes; and (3) does not cover any
losses, injuries to persons/property or costs. This warranty does give you specific
legal rights and you may have other rights, which vary from state to state. Be
careful, tools are dangerous if improperly used or maintained. Seller’s employees
are not qualified to advise you on the use of this Merchandise. Any oral
representation(s) made will not be binding on seller or its employees. The rights
under this limited warranty are to the original purchaser of the Merchandise and may
not be transferred to any subsequent owner. This limited warranty is in lieu of all
warranties, expressed or implied including warranties or merchantability and fitness
for a particular purpose. Seller shall not be liable for any special, incidental, or
consequential damages. The sole exclusive remedy against the seller will be for the
replacement of any defects as provided herein, as long as the seller is willing or
able to replace this product or is willing to refund the purchase price as provided
above. For insurance purposes, seller is not allowed to demonstrate any of these
power tools for you.
For questions / comments, technical assistance or repair parts – Please Call Toll
Free at: 1-866-917-4374. (M-F 8am – 6pm)
SAVE YOUR RECEIPTS
THIS WARRANTY IS VOID WITHOUT THEM
Page 14
© 2011 Menard, Inc., Eau Claire, WI 54703
Page 16
08/2011
Download PDF