Carrier | 48DL | Installation manual | Carrier 48DL Installation manual

INSTALLATION
MANUAL
SINGLE PACKAGE AIR CONDITIONERS AND
CONTENTS
SINGLE PACKAGE GAS/ELECTRIC UNITS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DL/DU -06, -07, -08, -10 and -12
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . 5
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6-1/2 TO 12-1/2 TON
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
(9.0 TO 11.5 EER)
RENEWAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
START-UP (COOLING) . . . . . . . . . . . . . . . . . . . . . . . . . 66
START-UP (GAS HEAT) . . . . . . . . . . . . . . . . . . . . . . . . 67
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . 74
See following pages for a complete Table of Contents.
NOTES, CAUTIONS AND WARNINGS
The installer should pay particular attention to the words:
NOTE, CAUTION, and WARNING. Notes are intended to
clarify or make the installation easier. Cautions are given
to prevent equipment damage. Warnings are given to alert
installer that personal injury and/or equipment damage
may result if installation procedure is not handled properly.
Tested in accordance with:
CAUTION:
READ ALL SAFETY GUIDES BEFORE YOU
BEGIN TO INSTALL YOUR UNIT.
SAVE THIS MANUAL
264975-BIM-B-1208
264975-BIM-B-1208
TABLE OF CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . 5
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
RENEWAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
INSTALLATION SAFETY INFORMATION . . . . . . . . . . . . 8
PRECEDING INSTALLATION . . . . . . . . . . . . . . . . . . . . . 8
LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
RIGGING AND HANDLING . . . . . . . . . . . . . . . . . . . . . . 11
CLEARANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
DUCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DUCT COVERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CONDENSATE DRAIN . . . . . . . . . . . . . . . . . . . . . . . . . . 16
COMPRESSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
THERMOSTAT WIRING . . . . . . . . . . . . . . . . . . . . . . . . . 17
POWER AND CONTROL WIRING . . . . . . . . . . . . . . . . . 17
POWER WIRING DETAIL . . . . . . . . . . . . . . . . . . . . . . . . 17
OPTIONAL ELECTRIC HEAT . . . . . . . . . . . . . . . . . . . . . 31
OPTIONAL GAS HEAT . . . . . . . . . . . . . . . . . . . . . . . . . . 31
GAS PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
GAS CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
LP UNITS, TANKS AND PIPING . . . . . . . . . . . . . . . . . . . . . . . 33
VENT AND COMBUSTION AIR . . . . . . . . . . . . . . . . . . . . . . . 33
OPTIONS/ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . 33
ELECTRIC HEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
MOTORIZED OUTDOOR DAMPER . . . . . . . . . . . . . . . . . . . . 33
ECONOMIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
POWER EXHAUST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
RAIN HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ECONOMIZER AND POWER EXHAUST SET POINT
ADJUSTMENTS AND INFORMATION . . . . . . . . . . . . . . . 34
MINIMUM POSITION ADJUSTMENT . . . . . . . . . . . . . . . . . . . 34
ENTHALPY SET POINT ADJUSTMENT . . . . . . . . . . . . . . . . . 34
POWER EXHAUST DAMPER SET POINT (WITH OR WITHOUT
POWER EXHAUST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
INDOOR AIR QUALITY AQ . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
PHASING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
BLOWER ROTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
BELT TENSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
AIR BALANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
CHECKING AIR QUANTITY . . . . . . . . . . . . . . . . . . . . . . 57
METHOD ONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
METHOD TWO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
SUPPLY AIR DRIVE ADJUSTMENT . . . . . . . . . . . . . . . 59
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
SEQUENCE OF OPERATIONS OVERVIEW . . . . . . . . . 61
COOLING SEQUENCE OF OPERATION . . . . . . . . . . . 61
CONTINUOUS BLOWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
INTERMITTENT BLOWER . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
NO OUTDOOR AIR OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . 61
ECONOMIZER WITH SINGLE ENTHALPY SENSOR - . . . . . 61
ECONOMIZER WITH DUAL ENTHALPY SENSORS - . . . . . . 62
ECONOMIZER WITH POWER EXHAUST - . . . . . . . . . . . . . . 62
MOTORIZED OUTDOOR AIR DAMPERS - . . . . . . . . . . . . . . 62
2
COOLING OPERATION ERRORS . . . . . . . . . . . . . . . . . . . . .62
HIGH-PRESSURE LIMIT SWITCH . . . . . . . . . . . . . . . . . . . . .62
LOW-PRESSURE LIMIT SWITCH . . . . . . . . . . . . . . . . . . . . . .62
FREEZESTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
LOW AMBIENT COOLING . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
COMPRESSOR PROTECTION . . . . . . . . . . . . . . . . . . . 63
FLASH CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
ELECTRIC HEATING SEQUENCE OF OPERATIONS . 63
ELECTRIC HEAT OPERATION ERRORS . . . . . . . . . . . 63
TEMPERATURE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
LIMIT SWITCH (LS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
FLASH CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
ELECTRIC HEAT ANTICIPATOR SETPOINTS . . . . . . . 64
GAS HEATING SEQUENCE OF OPERATIONS . . . . . . 64
IGNITION CONTROL BOARD . . . . . . . . . . . . . . . . . . . . 64
FIRST STAGE OF HEATING . . . . . . . . . . . . . . . . . . . . . . . . . .64
SECOND STAGE OF HEATING . . . . . . . . . . . . . . . . . . . . . . .64
RETRY OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
RECYCLE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
GAS HEATING OPERATION ERRORS . . . . . . . . . . . . . 64
LOCK-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
TEMPERATURE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
FLAME SENSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
GAS VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
LIMIT SWITCH (LS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
AUXILIARY LIMIT SWITCH (ALS) . . . . . . . . . . . . . . . . . . . . . .65
PRESSURE SWITCH (PS) . . . . . . . . . . . . . . . . . . . . . . . . . . .66
ROLLOUT SWITCH (ROS) . . . . . . . . . . . . . . . . . . . . . . . . . . .66
INTERNAL MICROPROCESSOR FAILURE . . . . . . . . . . . . . .66
FLASH CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
RESETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
GAS HEAT ANTICIPATOR SETPOINTS . . . . . . . . . . . .
START-UP (COOLING) . . . . . . . . . . . . . . . . . . . . . . . . . .
PRESTART CHECK LIST . . . . . . . . . . . . . . . . . . . . . . .
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . .
POST START CHECK LIST . . . . . . . . . . . . . . . . . . . . . .
START-UP (GAS HEAT) . . . . . . . . . . . . . . . . . . . . . . . . .
PRE-START CHECK LIST . . . . . . . . . . . . . . . . . . . . . . .
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . .
66
66
66
66
67
67
67
67
LIGHTING THE MAIN BURNERS . . . . . . . . . . . . . . . . . . . . . .67
POST START CHECKLIST . . . . . . . . . . . . . . . . . . . . . .
SHUT DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MANIFOLD GAS PRESSURE ADJUSTMENT . . . . . . . .
CHECKING GAS INPUT . . . . . . . . . . . . . . . . . . . . . . . .
67
67
67
68
NATURAL GAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
ADJUSTMENT OF TEMPERATURE RISE . . . . . . . . . .
BURNERS/ORIFICES INSPECTION/SERVICING . . . .
CHARGING THE UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL/DU FLASH CODES . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT CONTROL BOARD OPTION SETUP . . . . . . . . . . .
OPTION BYTE SETUP . . . . . . . . . . . . . . . . . . . . . . . . . .
HEAT DELAY SETUP . . . . . . . . . . . . . . . . . . . . . . . . . .
COOLING TROUBLESHOOTING GUIDE . . . . . . . . . . .
GAS HEAT TROUBLESHOOTING GUIDE . . . . . . . . . .
69
69
70
74
74
75
75
75
79
82
Johnson Controls Unitary Products
264975-BIM-B-1208
LIST OF FIGURES
Fig. #
1
Pg. #
Fig. #
Pg. #
UNIT SHIPPING BRACKET . . . . . . . . . . . . . . . . . . . . . 8
18 TYPICAL FIELD WIRING 24 VOLT THERMOSTAT . 18
2
CONDENSER COVERING . . . . . . . . . . . . . . . . . . . . . 8
3
COMPRESSOR SECTION . . . . . . . . . . . . . . . . . . . . . . 8
19 FIELD WIRING DISCONNECT - COOLING UNIT
WITH/WITHOUT ELECTRIC HEAT . . . . . . . . . . . . . . 19
4
DL/DU COMPONENT LOCATION (DL-10 SHOWN) . 10
5
UNIT 4 POINT LOAD . . . . . . . . . . . . . . . . . . . . . . . . . 11
6
UNIT 6 POINT LOAD . . . . . . . . . . . . . . . . . . . . . . . . . 12
7
UNIT CENTER OF GRAVITY . . . . . . . . . . . . . . . . . . . 12
8
UNIT DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 13
9
BOTTOM DUCT OPENINGS (FROM ABOVE) . . . . . 14
10 REAR DUCT DIMENSIONS . . . . . . . . . . . . . . . . . . . . 14
11 ROOF CURB DIMENSIONS . . . . . . . . . . . . . . . . . . . 15
12
TRANSITION ROOF CURBS . . . . . . . . . . . . . . . . . . 15
13 SIDE PANELS WITH HOLE PLUGS . . . . . . . . . . . . . 16
14 RETURN DOWNFLOW PLENUM WITH PANEL . . . . 16
15 DISCHARGE PANEL IN PLACE . . . . . . . . . . . . . . . . 16
16 CONDENSATE DRAIN . . . . . . . . . . . . . . . . . . . . . . . 16
17 TYPICAL ELECTRONIC THERMOSTAT FIELD
WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
20 FIELD WIRING DISCONNECT - COOLING UNIT WITH
GAS HEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
21 SIDE ENTRY GAS PIPING . . . . . . . . . . . . . . . . . . . . 31
22 BOTTOM ENTRY GAS PIPING . . . . . . . . . . . . . . . . . 31
23 ENTHALPY SET POINT CHART . . . . . . . . . . . . . . . . 35
24 HONEYWELL ECONOMIZER CONTROL W7212 . . 35
25 BELT ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . 36
26 DRY COIL DELTA P 50" CABINET . . . . . . . . . . . . . . 58
27 DRY COIL DELTA P 42" CABINET . . . . . . . . . . . . . . 58
28 TYPICAL FLAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
29 TYPICAL GAS VALVE . . . . . . . . . . . . . . . . . . . . . . . . 69
30 UNIT CONTROL BOARD . . . . . . . . . . . . . . . . . . . . . 75
31 BASIC TROUBLESHOOTING FLOWCHART . . . . . . 77
32 POWER ON FLOW CHART . . . . . . . . . . . . . . . . . . . 77
33 TRIP FAILURE FLOW CHART . . . . . . . . . . . . . . . . . 78
LIST OF TABLES
Tbl. #
Pg. #
1
UNIT VOLTAGE LIMITATIONS . . . . . . . . . . . . . . . . . . 10
2
UNIT TEMPERATURE LIMITATIONS . . . . . . . . . . . . . 10
3
UNIT WEIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4
4 POINT LOAD WEIGHT . . . . . . . . . . . . . . . . . . . . . . . 11
5
6 POINT LOAD WEIGHT . . . . . . . . . . . . . . . . . . . . . . . 12
6
UNIT HEIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7
UNIT CLEARANCES . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8
CONTROL WIRE SIZES . . . . . . . . . . . . . . . . . . . . . . . 17
9
ELECTRICAL DATA - DL-06 (6-1/2 TON) STANDARD
EFFICIENCY W/O PWRD CONV. OUTLET . . . . . . . . 20
10 ELECTRICAL DATA - DL-06 (6-1/2 TON) STANDARD
EFFICIENCY W/PWRD CONV. OUTLET . . . . . . . . . . 20
11 ELECTRICAL DATA - DU-06 (6-1/2 TON) HIGH
EFFICIENCY W/O PWRD CONV. OUTLET . . . . . . . . 21
12 ELECTRICAL DATA - DU-06 (6-1/2 TON) HIGH
EFFICIENCY W/PWRD CONV. OUTLET . . . . . . . . . . 21
13 ELECTRICAL DATA - DL-07 (7-1/2 TON) STANDARD
EFFICIENCY W/O PWRD CONV. OUTLET . . . . . . . . 22
14 ELECTRICAL DATA - DL-07 (7-1/2 TON) STANDARD
EFFICIENCY W/PWRD CONV. OUTLET . . . . . . . . . . 22
15 ELECTRICAL DATA - DU-07 (7-1/2 TON) HIGH
EFFICIENCY W/O PWRD CONV. OUTLET . . . . . . . . 23
16 ELECTRICAL DATA - DU-07 (7-1/2 TON) HIGH
EFFICIENCY W/PWRD CONV. OUTLET . . . . . . . . . . 23
Johnson Controls Unitary Products
Tbl. #
Pg. #
17 ELECTRICAL DATA - DL-08 (8-1/2 TON) STANDARD
EFFICIENCY W/O PWRD CONV. OUTLET . . . . . . . . 24
18 ELECTRICAL DATA - DL-08 (8-1/2 TON) STANDARD
EFFICIENCY W/PWRD CONV. OUTLET . . . . . . . . . . 24
19 ELECTRICAL DATA - DU-08 (8-1/2 TON) HIGH
EFFICIENCY W/O PWRD CONV. OUTLET . . . . . . . . 25
20 ELECTRICAL DATA - DU-08 (8-1/2 TON) HIGH
EFFICIENCY W/PWRD CONV. OUTLET . . . . . . . . . . 25
21 ELECTRICAL DATA - DL-10 (10 TON) STANDARD
EFFICIENCY W/O PWRD CONV. OUTLET . . . . . . . . 26
22 ELECTRICAL DATA - DL-10 (10 TON) STANDARD
EFFICIENCY W/PWRD CONV. OUTLET . . . . . . . . . . 26
23 ELECTRICAL DATA - DU-10 (10 TON) HIGH
EFFICIENCY W/O PWRD CONV. OUTLET . . . . . . . . 27
24 ELECTRICAL DATA - DU-10 (10 TON) HIGH
EFFICIENCY W/PWRD CONV. OUTLET . . . . . . . . . . 27
25 ELECTRICAL DATA - DL-12 (12-1/2 TON) STANDARD
EFFICIENCY W/O PWRD CONV. OUTLET . . . . . . . . 28
26 ELECTRICAL DATA - DL-12 (12-1/2 TON) STANDARD
EFFICIENCY W/PWRD CONV. OUTLET . . . . . . . . . . 28
27 ELECTRICAL DATA - DU-12 (12-1/2 TON) HIGH
EFFICIENCY W/O PWRD CONV. OUTLET . . . . . . . . 29
28 ELECTRICAL DATA - DU-12 (12-1/2 TON) HIGH
EFFICIENCY W/PWRD CONV. OUTLET . . . . . . . . . . 29
29 DL PHYSICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . 30
3
264975-BIM-B-1208
LIST OF TABLES (CONT’D)
Tbl. #
Pg. #
30 DU PHYSICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . 30
31 MINIMUM SUPPLY AIR CFM . . . . . . . . . . . . . . . . . . . 31
32 GAS APPLICATION DATA . . . . . . . . . . . . . . . . . . . . . 31
33 GAS PIPE SIZING - CAPACITY OF PIPE . . . . . . . . . . 32
Tbl. #
Pg. #
55 DL, DU-10 (10 TON) STANDARD MOTOR SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . 53
56 DL, DU-10 (10 TON) OPTIONAL MOTOR SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . 53
34 SUPPLY AIR LIMITATIONS . . . . . . . . . . . . . . . . . . . . 36
57 DL, DU-12 (12-1/2 TON) STANDARD MOTOR SIDE
SHOT BLOWER PERFORMANCE . . . . . . . . . . . . . . 54
35 DL-06 (6-1/2 TON) STANDARD MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . 37
58 DL, DU-12 (12-1/2 TON) OPTIONAL MOTOR SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . 54
36 DL-06 (6-1/2 TON) OPTIONAL MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . 37
59 INDOOR BLOWER SPECIFICATIONS . . . . . . . . . . . . 55
37 DU-06 (6-1/2 TON) STANDARD MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . 38
38 DU-06 (6-1/2 TON) OPTIONAL MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . 39
39 DL, DU-07 (7-1/2 TON) STANDARD MOTOR DOWN
SHOT BLOWER PERFORMANCE . . . . . . . . . . . . . . . 40
40 DL, DU-07 (7-1/2 TON) OPTIONAL MOTOR
DOWNSHOT BLOWER PERFORMANCE . . . . . . . . . 41
41 DL, DU-08 (8-1/2 TON) STANDARD MOTOR DOWN
SHOT BLOWER PERFORMANCE . . . . . . . . . . . . . . . 42
42 DL, DU-08 (8-1/2 TON) OPTIONAL DRIVE DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . 43
43 DL, DU-10 (10 TON) STANDARD MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . 44
60 POWER EXHAUST SPECIFICATIONS . . . . . . . . . . . 55
61 ADDITIONAL STATIC RESISTANCE DL-06, -10, -12
AND DU-10, -12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
62 ADDITIONAL STATIC RESISTANCE DL-07, -08 AND
DU-06, -07, -08 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
63 MOTOR SHEAVE DATUM DIAMETERS . . . . . . . . . . 61
64 ELECTRIC HEAT LIMIT SETTING 50” CABINET . . . . 63
65 ELECTRIC HEAT LIMIT SETTING 42” CABINET . . . . 64
66 ELECTRIC HEAT ANTICIPATOR SETPOINTS . . . . . 64
67 GAS HEAT LIMIT CONTROL SETTINGS . . . . . . . . . . 65
68 GAS HEAT ANTICIPATOR SETPOINTS . . . . . . . . . . 66
69 GAS HEAT STAGES . . . . . . . . . . . . . . . . . . . . . . . . . . 68
70 GAS RATE CUBIC FEET PER HOUR . . . . . . . . . . . . 68
44 DL, DU-10 (10 TON) OPTIONAL MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . 44
71 DL-06 (6.5 TON) STANDARD EFFICIENCY
SUPERHEAT CHARGING . . . . . . . . . . . . . . . . . . . . . 70
45 DL, DU-12 (12-1/2 TON) STANDARD MOTOR DOWN
SHOT BLOWER PERFORMANCE . . . . . . . . . . . . . . . 45
72 DL-07 (7.5 TON) STANDARD EFFICIENCY
SUPERHEAT CHARGING . . . . . . . . . . . . . . . . . . . . . 70
46 DL, DU-12 (12-1/2 TON) OPTIONAL MOTOR DOWN
SHOT BLOWER PERFORMANCE . . . . . . . . . . . . . . . 45
73 DL-08 (8.5 TON) STANDARD EFFICIENCY
SUPERHEAT CHARGING . . . . . . . . . . . . . . . . . . . . . 71
47 DL-06 (6-1/2 TON) STANDARD MOTOR SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . 46
74 DL -10 (10 TON) STANDARD EFFICIENCY
SUPERHEAT CHARGING . . . . . . . . . . . . . . . . . . . . . 71
48 DL-06 (6-1/2 TON) OPTIONAL MOTOR SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . 46
75 DL-12 (12.5 TON) STANDARD EFFICIENCY
SUPERHEAT CHARGING . . . . . . . . . . . . . . . . . . . . . 72
49 DU-06 (6-1/2 TON) STANDARD MOTOR SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . 47
76 DU-06 (6.5 TON) HIGH EFFICIENCY SUPERHEAT
CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
50 DU-06 (6-1/2 TON) OPTIONAL MOTOR SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . 48
77 DU-07 (7.5 TON) HIGH EFFICIENCY SUPERHEAT
CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
51 DL, DU-07 (7-1/2 TON) STANDARD MOTOR SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . 49
78 DU-08 (8.5 TON) HIGH EFFICIENCY SUPERHEAT
CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
52 DL, DU-07 (7-1/2 TON) OPTIONAL SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . 50
79 DU-12 (12.5 TON) HIGH EFFICIENCY SUPERHEAT
CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
53 DL, DU-08 (8-1/2 TON) STANDARD MOTOR SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . 51
80 UNIT CONTROL BOARD FLASH CODES . . . . . . . . . 74
54 DL, DU-08 (8-1/2 TON) OPTIONAL DRIVE SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . 52
82 IGNITION CONTROL FLASH CODES . . . . . . . . . . . . 76
4
81 HEAT DELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Johnson Controls Unitary Products
264975-BIM-B-1208
GENERAL
DL/DU units are single package air conditioners with optional
gas heating designed for outdoor installation on a rooftop or
slab and for non-residential use. These units can be
equipped with factory or field installed electric heaters for
heating applications.
These units are completely assembled on rigid, permanently
attached base rails. All piping, refrigerant charge, and electrical wiring is factory installed and tested. The units require
electric power, gas supply (where applicable), and duct connections. The electric heaters have nickel-chrome elements
and utilize single-point power connection.
If the information in this manual is not followed
exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
WHAT TO DO IF YOU SMELL GAS:
a.
Do not try to light any appliance.
b.
Do not touch any electrical switch; do not use
any phone in your building.
c.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
d.
If you cannot reach your gas supplier, call the fire
department.
SAFETY CONSIDERATIONS
Should overheating occur, or the gas supply fail to
shut off, shut off the manual gas valve to the furnace
before shutting off the electrical supply.
Do not use this furnace if any part has been under
water. Immediately call a qualified service technician
to inspect the furnace and to replace any part of the
control system and any gas control which has been
under water.
Due to system pressure, moving parts, and electrical components, installation and servicing of air conditioning equipment
can be hazardous. Only qualified, trained service personnel
should install, repair, or service this equipment. Untrained
personnel can perform basic maintenance functions of cleaning coils and filters and replacing filters.
Observe all precautions in the literature, labels, and tags
accompanying the equipment whenever working on air conditioning equipment. Be sure to follow all other applicable
safety precautions and codes including ANSI Z223.1 or CSAB149.1- latest edition.
Wear safety glasses and work gloves. Use quenching cloth
and have a fire extinguisher available during brazing operations.
Johnson Controls Unitary Products
Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
INSPECTION
As soon as a unit is received, it should be inspected for possible damage during transit. If damage is evident, the extent of
the damage should be noted on the carrier’s freight bill. A
separate request for inspection by the carrier’s agent should
be made in writing.
This furnace is not to be used for temporary heating
of buildings or structures under construction.
Before performing service or maintenance operations on unit, turn off main power switch to unit. Electrical shock could cause personal injury. Improper
installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer
to this manual. For assistance or additional information consult a qualified installer, service agency or
the gas supplier.
5
264975-BIM-B-1208
REFERENCE
APPROVALS
Additional information is available in the following reference
forms:
Design certified by CSA as follows:
1.
For use as a cooling only unit, cooling unit with supplemental electric heat or a forced air furnace.
2.
For outdoor installation only.
3.
For installation on combustible material and may be
installed directly on combustible flooring or, in the U.S.,
on wood flooring or Class A, Class B or Class C roof covering materials.
4.
For use with natural gas (convertible to LP with kit).
• Technical Guide - DU-06 thru -12, 246650
• Technical Guide - DL-06 thru -12, 246713
• General Installation - DU/DL-06 thru -12, 264975
• Pre-start & Post-start Check List
• Economizer Accessory Downflow Factory Installed
Downflow Field Installed
Horizontal Field Installed
• Motorized Outdoor Air Damper
• Manual Outdoor Air Damper (0-100%)
• Manual Outdoor Air Damper (0-35%)
• Gas Heat Propane Conversion Kit
• Gas Heat High Altitude Kit (Natural Gas)
• Gas Heat High Altitude Kit (Propane)
This product must be installed in strict compliance
with the enclosed installation instructions and any
applicable local, state, and national codes including,
but not limited to, building, electrical, and mechanical
codes.
• –60°F Gas Heat Kit
• Electric Heater Accessory 50” cabinet
• Electric Heater Accessory 42” cabinet
RENEWAL PARTS
Contact your local UP parts distribution center for authorized
replacement parts.
Improper installation may create a condition where the
operation of the product could cause personal injury
or property damage.
The installer should pay particular attention to the words:
NOTE, CAUTION, and WARNING. NOTES are intended to
clarify or make the installation easier. CAUTIONS are given
to prevent equipment damage. WARNINGS are given to alert
installer that personal injury and/or equipment damage may
result if installation procedure is not handled properly.
6
Johnson Controls Unitary Products
264975-BIM-B-1208
NOMENCLATURE
6.5-12.5 Ton Single Package Model Number Nomenclature
D U -10 N18 A T A AA 3 0 1 2 4 A
Product Category
Product Style
D = A/C, Single Pkg., R-22
A = Style A
B = Style B
Product Identifier
Configuration Options (not required for all units)
These four digits will not be assigned until a quote is requested, or an order placed.
L = 9.0 EER A/C
U = 11.0+ EER A/C
SS Drain Pan
CPC Controller, DFS, APS
Johnson Controller, DFS, APS
Nominal Cooling Capacity
Honeywell Controller, DFS, APS
Novar Controller, DFS, APS
-06 = 6.5 Ton
-07 = 7.5 Ton
-08 = 8.5 Ton
-10 = 10.0 Ton
-12 = 12.5 Ton
Simplicity IntelliComfort Controller
Simplicity IntelliComfort Controller w/ModLinc
2" Pleated filters
BAS Ready Unit with Economizer
Shipping Bag
Any Combination of Additional Options that Don’t Have an Option Code Pre-assigned
Heat Type and Nominal Heat Capacity
C00 = Cooling Only. No heat installed
Product Generation
Gas Heat Options
3 = Third Generation
4 = Fourth Generation
5 = Fifth Generation
6 = Sixth Generation
N12 = 120 MBH Input Aluminized Steel
N18 = 180 MBH Input Aluminized Steel
N24 = 240 MBH Input Aluminized Steel
S12 = 120 MBH Input Stainless Steel
S18 = 180 MBH Input Stainless Steel
S24 = 240 MBH Input Stainless Steel
Additional Options
Electric Heat Options
AA = None
AB = Phase Monitor
AC = Coil Guard
AD = Dirty Filter Switch
AE = Phase Monitor & Coil Guard
AF = Phase Monitor & Dirty Filter Switch
AG = Coil Guard & Dirty Filter Switch
AH = Phase Monitor, Coil Guard & Dirty Filter Switch
E09 = 9 KW
E18 = 18 KW
E24 = 24 KW
E36 = 36 KW
E54 = 54 KW
TA = Technicoat Condenser Coil
TJ = Technicoat Evaporator Coil
TS = Technicoat Evaporator & Condenser Coils
ZZ = If desired option combination is not listed above, ZZ will be assigned and configuration options will be
located in digits 15-18.
Airflow
A = Std. Motor
B = Std. Motor/Econo./Barometric Relief (Downflow
Only)
C = Std. Motor/Econo./Power Exhaust (Downflow Only)
D = Std. Motor/Motorized Damper (Downflow Only)
E = Std. Motor/Horizontal Economizer (No Baro.)
F = Std. Motor/Slab Econo./Power Exhaust
(Downflow Only)
G = Std. Motor/Slab Econo./Barometric Relief
(Downflow Only)
N = Hi Static
P = Hi Static/Econo./Barometric Relief
(Downflow Only)
Q = Hi Static/Econo./Power Exhaust
(Downflow Only)
R = Hi Static/Motorized Damper (Downflow Only)
S = Hi Static/Horizontal Economizer (No Baro.)
T = Hi Static/Slab Econo./Power Exhaust
(Downflow Only)
U = Hi Static/Slab Econo./Barometric Relief
(Downflow only)
Voltage
T = 208/230-3-60
W = 460-3-60
X = 575-3-60
Installation Options
A = No Options Installed
B = Option 1
C = Option 2
D = Options 1 & 2
E = Option 3
F = Option 4
G = Options 1 & 3
H = Options 1 & 4
J = Options 1, 2 & 3
K = Options 1, 2, & 4
L = Options 1,3 & 4
M = Options 1, 2, 3, & 4
N = Options 2 & 3
P = Options 2 & 4
Q = Options 2, 3, & 4
R = Options 3 & 4
S = Option 5
T = Options 1 & 5
U = Options 1, 3, & 5
V = Options 1, 4, & 5
W = Options 1, 3, 4, & 5
X = Options 3 & 5
Y = Options 4 & 5
Z = Options 3, 4 & 5
Options
1 = Disconnect
2 = Non-Pwr'd Conv. Outlet
3 = Smoke Detector S.A.
4 = Smoke Detector R.A.
5 = Pwr'd Conv. Outlet
Johnson Controls Unitary Products
7
264975-BIM-B-1208
INSTALLATION
2.
Turn each bracket toward the ground and the protective
plywood covering will drop to the ground.
3.
Remove the condenser coil external protective covering
prior to operation.
4.
Remove the toolless doorknobs and instruction packet
prior to installation.
INSTALLATION SAFETY INFORMATION
Read these instructions before continuing this appliance
installation. This is an outdoor combination heating and cooling unit. The installer must assure that these instructions are
made available to the consumer and with instructions to
retain them for future reference.
1.
Refer to the furnace rating plate for the approved type of
gas for this furnace.
2.
Install this furnace only in a location and position as
specified on Page 13 of these instructions.
3.
Never test for gas leaks with an open flame. Use commercially available soap solution made specifically for
the detection of leaks when checking all connections, as
specified on Pages 8, 32, 33 and 67 of these instructions.
4.
Always install furnace to operate within the furnace's
intended temperature-rise range with the duct system
and within the allowable external static pressure range,
as specified on the unit name/rating plate, specified on
Page 69 of these instructions.
5.
Condenser
Coil External
Protective
Covering
Barometric
Relief Hood in
Shipping Location (if included)
FIGURE 2 -
CONDENSER COVERING
This equipment is not to be used for temporary heating
of buildings or structures under construction.
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly could
result in serious injury, death or property damage.
Toolless
Doorknobs
Never test for gas leaks with an open flame. use a
commercially available soap solution made specifically for the detection of leaks to check all connections. A fire or explosion may result causing property
damage, personal injury or loss of life.
Installation
Instruction
Packet
PRECEDING INSTALLATION
1.
Remove the two screws holding the brackets in the front,
rear and compressor side fork-lift slots.
Bracket
Screws
FIGURE 1 -
8
FIGURE 3 -
COMPRESSOR SECTION
Turn down
UNIT SHIPPING BRACKET
Johnson Controls Unitary Products
264975-BIM-B-1208
In Canada:
This product must be installed in strict compliance
with the enclosed installation instructions and any
applicable local, state and national codes including,
but not limited to, building, electrical, and mechanical codes.
The furnace and its individual shut-off valve must be
disconnected from the gas supply piping system
during any pressure testing at pressures in excess
of 1/2 PSIG.
Pressures greater than 1/2 PSIG will cause gas
valve damage resulting in a hazardous condition. If it
is subjected to a pressure greater than 1/2 PSIG, the
gas valve must be replaced.
The furnace must be isolated from the gas supply
piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less
than 1/2 PSIG.
LIMITATIONS
1.
Canadian Electrical Code, CSA C22.1
2.
Installation Codes, CSA - B149.1.
3.
Local plumbing and waste water codes, and
4.
Other applicable local codes.
Refer to Tables 1 & 2 for unit application data.
After installation, gas fired units must be adjusted to obtain a
temperature rise within the range specified on the unit rating
plate.
If components are to be added to a unit to meet local codes,
they are to be installed at the dealer’s and/or customer’s
expense.
Size of unit for proposed installation should be based on heat
loss/heat gain calculation made according to the methods of
Air Conditioning Contractors of America (ACCA).
This furnace is not to be used for temporary heating of buildings or structures under construction.
These units must be installed in accordance with the following:
In U.S.A.:
1.
National Electrical Code, ANSI/NFPA No. 70 - Latest
Edition
2.
National Fuel Gas Code, ANSI Z223.1 - Latest Edition
3.
Gas-Fired Central Furnace Standard, ANSI Z21.47a. Latest Edition
4.
Local building codes, and
5.
Local gas utility requirements
Johnson Controls Unitary Products
The Simplicity® control board used in this product
will effectively operate the cooling system down to
0°F when this product is applied in a comfort cooling
application for people. An economizer is typically
included in this type of application. When applying
this product for process cooling applications (computer rooms, switchgear, etc.), please reference
applications bulletin AE-011-07 or call the applications department for Unitary Products @ 1-877UPG-SERV for guidance. Additional accessories
may be needed for stable operation at temperatures
below 30° F.
9
264975-BIM-B-1208
Terminal Block
for Hi-Voltage
Connection
Simplicity ® Control Board
w/Screw Connector for Tstat Wiring and Network
Connection
Disconnect Location
(Optional Disconnect Switch)
Filter Access
(2” Filters)
Filter-Drier (Solid Core)
Condenser
Section
Second model
nameplate inside
hinged access
panel
Belt-Drive
Blower
Motor
Dual stage
cooling for
maximum
comfort
Slide-out motor
and blower
assembly for
ease of adjustment and service
Compressor #2
Access (HighEff Compressor
w/ crankcase
heater)
Base Rails w/ Forklift
Slots (3 Sides) & Lifting Holes
Roof curbs in eight- and
fourteen-inch heights.
Rood curbs for transitioning from DHB/DHC/DUS
footprint to the DU/DC
Series footprint are also
available (field-installed
accessory)
FIGURE 4 -
Power Ventor Motor
Toolless
door latch
Side entry power
and control wiring
knockouts
Compressor #1 Access (High-Eff
Compressor w/ crankcase heater)
LOCATION
Power Rating1
Minimum
Maximum
208/230-3-60
460-3-60
575-3-60
187
432
540
252
504
630
Utilization range “A” in accordance with ARI Standard 110.
Use the following guidelines to select a suitable location for
these units:
1.
Unit is designed for outdoor installation only.
2.
Condenser coils must have an unlimited supply of air.
Where a choice of location is possible, position the unit
on either north or east side of building.
3.
Suitable for mounting on roof curb.
4.
For ground level installation, use a level concrete slab
with a minimum thickness of 4 inches. The length and
width should be at least 6 inches greater than the unit
base rails. Do not tie slab to the building foundation.
5.
Roof structures must be able to support the weight of the
unit and its options/accessories. Unit must be installed on
a solid, level roof curb or appropriate angle iron frame.
TABLE 2: UNIT TEMPERATURE LIMITATIONS
Temperature
Min.
Max.
Wet Bulb Temperature (°F) of Air on
Evaporator Coil
57
72
Dry Bulb Temperature (°F) of Air on
Condenser Coil
01
125
1.
10
Intelligent control board for
safe and efficient operation
DL/DU COMPONENT LOCATION (DL-10 SHOWN)
TABLE 1: UNIT VOLTAGE LIMITATIONS
1.
Two-stage gas heating to maintain
warm, comfortable
temperature
Slide-Out Drain
Pan w/ Steel 3/4”
NPT, Female
Connection
A low ambient accessory is available for operation
down to -20°F.
Johnson Controls Unitary Products
264975-BIM-B-1208
6.
Maintain level tolerance to 1/2” across the entire width
and length of unit.
Excessive exposure of this furnace to contaminated
combustion air may result in equipment damage or
personal injury. Typical contaminates include: permanent wave solution, chlorinated waxes and cleaners, chlorine based swimming pool chemicals, water
softening chemicals, carbon tetrachloride, Halogen
type refrigerants, cleaning solvents (e.g. perchloroethylene), printing inks, paint removers, varnishes,
hydrochloric acid, cements and glues, antistatic fabric softeners for clothes dryers, masonry acid washing materials.
RIGGING AND HANDLING
Exercise care when moving the unit. Do not remove any
packaging until the unit is near the place of installation. Rig
the unit by attaching chain or cable slings to the lifting holes
provided in the base rails. Spreader bars, whose length
exceeds the largest dimension across the unit, MUST be
used across the top of the unit.
If a unit is to be installed on a roof curb other than a
UP roof curb, gasketing must be applied to all surfaces that come in contact with the unit underside.
C
D
FIGURE 5 -
UNIT 4 POINT LOAD
TABLE 3: UNIT WEIGHTS
Model
Shipping Weight1 (lb.)
Operating Weight1 (lb.)
DL-06
1056
1041
DL-07
865
860
DL-08
880
875
DL-10
1131
1116
DL-12
1210
1195
DU-06
888
883
DU-07
895
890
DU-08
905
900
DU-10
1222
1207
DU-12
1212
1197
w/Econ.
85
84
w/ PE
150
148
w/Elec. Heat
49
49
2
110
110
1.
54 kW heater.
2.
8 Tube Heat Exchanger.
TABLE 4: 4 POINT LOAD WEIGHT
Units may be moved or lifted with a forklift. Slotted openings
in the base rails are provided for this purpose.
Location (lbs.)1
Model
LENGTH OF FORKS MUST BE A MINIMUM OF 60
INCHES.
All panels must be secured in place when the unit is
lifted.
The condenser coils should be protected from rigging cable damage with plywood or other suitable
material.
1.
Johnson Controls Unitary Products
B
A
w/Gas Heat
Before lifting, make sure the unit weight is distributed equally on the rigging cables so it will lift evenly.
F R O N T
L E F T
A
B
C
D
DL-06
228
195
285
333
DL-07
192
143
224
301
DL-08
195
146
228
306
DL-10
245
209
305
357
DL-12
262
224
327
382
DU-06
197
147
230
309
DU-07
199
148
232
311
DU-08
201
150
234
315
DU-10
265
226
330
386
DU-12
263
224
327
383
Weights include largest gas heat option.
11
264975-BIM-B-1208
CLEARANCES
TABLE 5: 6 POINT LOAD WEIGHT
Location (lbs.)1
Model
A
B
C
D
E
F
DL-06
156
140
127
185
205
228
DL-07
135
110
91
142
172
211
DL-08
137
112
93
145
175
214
DL-10
168
151
136
198
219
244
DL-12
180
161
145
212
235
262
DU-06
138
113
93
146
176
216
DU-07
139
113
94
147
128
218
DU-08
141
115
95
149
180
221
DU-10
181
163
147
214
237
264
DU-12
180
161
146
213
235
262
1.
All units require particular clearances for proper operation
and service. Installer must make provisions for adequate
combustion and ventilation air in accordance with section 5.3
of Air for Combustion and Ventilation of the National Fuel Gas
Code, ANSI Z223.1 – Latest Edition (in U.S.A.), or Sections
7.2, 7.3, or 7.4 of Gas Installation Codes, CSA-B149.1 (in
Canada) - Latest Edition, and/or applicable provisions of the
local building codes. Refer to Table 7 for clearances required
for combustible construction, servicing, and proper unit operation.
Weights include largest gas heat option.
Do not permit overhanging structures or shrubs to
obstruct condenser air discharge outlet, combustion
air inlet or vent outlets.
Excessive exposure to contaminated combustion air
will result in safety and performance related problems. To maintain combustion air quality, the recommended source of combustion air is the outdoor air
supply. The outdoor air supplied for combustion
should be free from contaminants due to chemical
exposure that may be present from the following
sources.
F R O N T
L E F T
D
C
B
A
E
F
FIGURE 6 -
UNIT 6 POINT LOAD
X
LEFT
Commercial buildings
Indoor pools
Laundry rooms
Hobby or craft rooms
Chemical storage areas
Y
The following substances should be avoided to
maintain outdoor combustion air quality.
FRONT
Unit Model Number
X
Y
DL-06
47 1/2
25 1/2
DL-07
38
23
DL-08
38
23
DL-10
47 1/2
25 1/2
FIGURE 7 -
12
•
•
•
•
•
DL-12
47 1/2
25 1/2
DU-06
38
23
DU-07
38
23
DU-08
38
23
DU-10
47 1/2
25 1/2
DU-12
47 1/2
25 1/2
•
•
•
•
•
•
•
•
•
•
•
•
•
Permanent wave solutions
Chlorinated waxes and cleaners
Chlorine based swimming pool cleaners
Water softening chemicals
De-icing salts or chemicals
Carbon tetrachloride
Halogen type refrigerants
Cleaning solvents (such as perchloroethylene)
Printing inks, paint removers, varnishes, etc.
Hydrochloric acid
Cements and glues
Anti-static fabric softeners for clothes dryers
Masonry acid washing materials
UNIT CENTER OF GRAVITY
Johnson Controls Unitary Products
264975-BIM-B-1208
30-11/32
X
See Detail
A
Control
Entry
Ø 7/8
Power
Entry
Ø 2-1/2
Power
Entry
Ø 2-1/2
4-1/4
11-1/2
Convenience
Power
Outlet
Entry
Ø 7/8
17-3/16
30-3/16
59
24-3/16
FIGURE 8 -
For Drain
Dimensions
See Detail C
6-3/16
LEFT
For Baserail
Dimensions
See Detail B
FRONT
89
27
UNIT DIMENSIONS
NOTE: A one-inch clearance must be provided between
any combustible material and the supply ductwork
for a distance of 3 feet from the unit.
TABLE 6: UNIT HEIGHT
Unit Model Number
X
DL-06
DL-07
DL-08
DL-10
DL-12
DU-06
DU-07
DU-08
DU-10
DU-12
50 3/4
42
DETAIL B
42
2 -3 /8
50 3/4
50 3/4
42
3 -3 /4
42
42
50 3/4
50 3/4
3 -9 /1 6
TABLE 7: UNIT CLEARANCES
Top1
1.
72”
Right
12”
2
Front
36”
Left
36”
Rear3
36”
Bottom4
0”
DETAIL C
Units must be installed outdoors. Overhanging structure or
shrubs should not obstruct condenser air discharge outlet.
5 -3 /8
2.
The products of combustion must not be allowed to
accumulate within a confined space and re-circulate.
3.
To remove the slide-out drain pan, a rear clearance of
sixty inches is required. If space is unavailable, the
drain pan can be removed through the front by separating the corner wall.
NOTE: If the unit includes gas heating, locate the unit so
the flue exhaust is at least:
Units may be installed on combustible floors made from
wood or class A, B or C roof covering materials.
•
Three (3) feet above any forced air inlet located within 10
horizontal feet (excluding those integral to the unit).
•
Four (4) feet below, four (4) horizontal feet from, or one
(1) foot above any door or gravity air inlet into the building.
•
Four (4) feet from electric meters, gas meters, regulators, and relief equipment.
4.
DETAIL A
G a s P ip e In le t
5 -1 /4
B a s e
P a n
1 7 -1 3 /1 6
V ie w o f W a ll A c r o s s fr o m
Johnson Controls Unitary Products
C o il
13
264975-BIM-B-1208
.
32-11/16
6-13/16
Supply
Air
6-13/16
6-13/16
Return
Air
24
LEFT
27-1/2
21
18
21-3/16
19-3/16
17-3/16
12-5/16
7-1/8
FRONT
14-23/32
16-3/8
18-1/16
19-5/8
Bottom
Condensate
Drain
Bottom
Power, Control and
Convenience Outlet
Wiring Entries
Bottom
Gas Supply Entry
63-1/2
FIGURE 9 -
BOTTOM DUCT OPENINGS (FROM ABOVE)
18-1/4
Dot Plugs
REAR DUCT DIMENSIONS
CABINET SIZE
DIMENSION
“A”
“B”
“C”
50 3/4”
28 1/4
18 1/16
28 1/4
42”
27 3/4
12 1/16
27 1/2
Supply
Air
Return
Air
A
18-1/4
B
5-5/32
2-31/32
C
31-11/16
FIGURE 10 - REAR DUCT DIMENSIONS
14
Johnson Controls Unitary Products
264975-BIM-B-1208
DUCTWORK
DUCT COVERS
Ductwork should be designed and sized according to the
methods in Manual D of the Air Conditioning Contractors of
America (ACCA) or as recommended by any other recognized authority such as ASHRAE or SMACNA.
Units are shipped with the side duct openings covered and a
covering over the bottom of the unit. For bottom duct application, no duct cover changes are necessary. For side duct
application, remove the side duct covers and install over the
bottom duct openings. The panels removed from the side
duct connections are designed to be reused by securing each
panel to its respective downflow opening. But keep in mind
that the supply panel is installed with the painted surface UP,
facing the heat exchanger, while the return panel is installed
with the painted surface DOWN, facing the downflow duct
opening. The supply panel is secured with the bracket
(already in place from the factory) and two screws. It’s a snug
fit for the panel when sliding it between the heat exchanger
and unit bottom, but there is room. The return panel is
secured with four screws.
A closed return duct system should be used. This will not
preclude use of economizers or outdoor fresh air intake. The
supply and return air duct connections at the unit should be
made with flexible joints to minimize noise.
The supply and return air duct systems should be designed
for the CFM and static pressure requirements of the job. They
should NOT be sized to match the dimensions of the duct
connections on the unit.
Refer to Figure 9 for bottom air duct openings. Refer to Figure 10 for rear air duct openings.
R IG H T
8 0 -5 /8
IN S U L A T E D D E C K U N D E R
C O N D E N S E R S E C T IO N
2 0
2 0
S U P P L Y
6
R E T U R N
2 T Y P .
3 0
IN S U L A T E D D E C K U N D E R
C O M P R E S S O R S E C T IO N
5 0 -1 /2
F R O N T
8 o r 1 4
FIGURE 11 - ROOF CURB DIMENSIONS
2 T Y P
5 0 -1 /2
3 0 -1 /2
2 3
4
8 0 -5 /8
2 6
R E T U R N
S U P P L Y
1 0
7 6 -5 /8
9 4
F R O N T
5 9 -1 /4
6 4 -1 /4
R IG H T
FIGURE 12 - TRANSITION ROOF CURBS
Johnson Controls Unitary Products
15
264975-BIM-B-1208
CONDENSATE DRAIN
When fastening ductwork to side duct flanges on
unit, insert screws through duct flanges only. DO
NOT insert screws through casing. Outdoor ductwork must be insulated and water-proofed.
The side condensate drain is reversible and maybe re-oriented to the rear of the cabinet to facilitate condensate piping. A condensate drain connection is available through the
base pan for piping inside the roof curb. Trap the connection
per Figure 16. The trap and drain lines should be protected
from freezing.
Plumbing must conform to local codes. Use a sealing compound on male pipe threads. Install condensate drain line
from the 3/4 inch NPT female connection on the unit to an
open drain.
O P T IO N A L C O IL
G U A R D
3 " M in im u m
FIGURE 13 - SIDE PANELS WITH HOLE PLUGS
Note orientation. Panel is “insulation” side up.
FIGURE 16 - CONDENSATE DRAIN
COMPRESSORS
The compressors are mounted on elastomer insulators. The
mounting bolts have been fully tightened for shipping.
Do not loosen the compressor mounting bolts.
FIGURE 14 - RETURN DOWNFLOW PLENUM WITH
PANEL
FILTERS
Two-inch filters are supplied with each unit. One-inch filters
may be used with no modification to the filter racks. Filters
must always be installed ahead of evaporator coil and must
be kept clean or replaced with same size and type. Dirty filters reduce the capacity of the unit and result in frosted coils
or safety shutdown. Refer to physical data tables, for the
number and size of filters needed for the unit. The unit should
not be operated without filters properly installed.
Make sure that panel latches are properly positioned
on the unit to maintain an airtight seal.
FIGURE 15 - DISCHARGE PANEL IN PLACE
16
Johnson Controls Unitary Products
264975-BIM-B-1208
THERMOSTAT WIRING
The thermostat should be located on an inside wall approximately 56 inch above the floor where it will not be subject to
drafts, sun exposure or heat from electrical fixtures or appliances. Follow the manufacturer's instructions enclosed with
thermostat for general installation procedure. Seven (7) colorcoded, insulated wires should be used to connect the thermostat to the unit. Refer to Table 8 for control wire sizing and
maximum length.
TABLE 8: CONTROL WIRE SIZES
1.
Wire Size
Maximum Length1
18 AWG
150 Feet
From the unit to the thermostat and back to the unit.
POWER AND CONTROL WIRING
Field wiring to the unit, fuses, and disconnects must conform
to provisions of National Electrical Code (NEC), ANSI/NFPA
No. 70 – Latest Edition (in U.S.A.), current Canadian Electrical Code C221, and/or local ordinances. The unit must be
electrically grounded in accordance with NEC and CEC as
specified above and/or local codes.
A disconnect must be utilized for these units. Factory
installed disconnects are available. If installing a disconnect
(field supplied or UP supplied accessory), refer to Figure 4 for
the recommended mounting location.
Avoid damage to internal components if drilling
holes for disconnect mounting.
NOTE: Since not all local codes allow the mounting of a disconnect on the unit, please confirm compliance with
local code before mounting a disconnect on the unit.
Electrical line must be sized properly to carry the load. USE
COPPER CONDUCTORS ONLY. Each unit must be wired
with a separate branch circuit fed directly from the meter
panel and properly fused.
Refer to Figures 17, 18 and 19 for typical field wiring and to
the appropriate unit wiring diagram mounted inside control
doors for control circuit and power wiring information.
Voltage tolerances which must be maintained at the compressor terminals during starting and running conditions are
indicated on the unit Rating Plate and Table 1.
208/230-3-60 and 380/415-3-50 units control transformers are factory wired for 230v and 415v power
supply respectively. Change tap on transformer for
208-3-60 or 380-3-50 operation. See unit wiring diagram.
The internal wiring harnesses furnished with this unit are an
integral part of the design certified unit. Field alteration to
comply with electrical codes should not be required. If any of
the wire supplied with the unit must be replaced, replacement
wire must be of the type shown on the wiring diagram and the
same minimum gauge as the replaced wire.
Johnson Controls Unitary Products
When connecting electrical power and control wiring
to the unit, water-proof connectors must be used so
that water or moisture cannot be drawn into the unit
during normal operation. The above water-proofing
conditions will also apply when installing a field supplied disconnect switch.
POWER WIRING DETAIL
Units are factory wired for the voltage shown on the unit
nameplate. Refer to Electrical Data Tables 9 to 28 to size
power wiring, fuses, and disconnect switch.
Power wiring is brought into the unit through the side of the
unit or the basepan inside the curb.
17
264975-BIM-B-1208
T H E R M
T E R M
O S T A T
IN A L S
1
U N IT T E R M IN A L S
S T R IP T B 1
R C
R H
R
Y 1
Y 1
Y 2
Y 2
W
1
W
W
2
1
W
G
208/230-3-60 and 380/415-3-50 units control transformers are factory wired for 230v and 415v power
supply respectively. Change tap on transformer for
208-3-60 or 380-3-50 operation. See unit wiring diagram.
2
G
C
C
X 1
2 4
V o lt
T r a n s fo r m
X
2
X 3
e r
O C C
X 4
A 1
A 2
T
T
T O R E M O T E S E N S O R
2 E T 0 4 7 0 1 3 2 4 IF U S E D
1
2
E le c tr o n ic p r o g r a m m a b le T h e r m o s ta t 2 E T 0 7 7 0 0 1 0 0 2 4 ( in c lu d e s s u b b a s e ) .
T e r m in a ls A 1 a n d A 2 p r o v id e a r e la y o u tp u t to c lo s e th e o u td o o r
e c o n o m iz e r d a m p e r s w h e n th e th e r m o s ta t s w itc h e s to th e s e t- b a c k p o s itio n .
FIGURE 17 - TYPICAL ELECTRONIC THERMOSTAT FIELD WIRING
T -S T A T
W 1
W 1
W 2
W 2
Y 1
Y 1
G
G
Y 2
O C C
R H
R C
R E M O T E
M IN P O S
C
U N IT C O N T R O L
B O A R D
Y 2
X
R
S D
C
FIGURE 18 - TYPICAL FIELD WIRING 24 VOLT THERMOSTAT
18
Johnson Controls Unitary Products
264975-BIM-B-1208
TERMINAL BLOCK TB1
FACTORY OR FIELD
SUPPLIED DISCONNECT
GROUND
LUG
THREE
PHASE
POWER
SUPPLY
FIGURE 19 - FIELD WIRING DISCONNECT - COOLING UNIT WITH/WITHOUT ELECTRIC HEAT
CONTACTOR 1M
GROUND
LUG
T1
T2
T3
L1
L2
L3
FACTORY OR FIELD
SUPPLIED DISCONNECT
THREE
PHASE
POWER
SUPPLY
FIGURE 20 - FIELD WIRING DISCONNECT - COOLING UNIT WITH GAS HEAT
Johnson Controls Unitary Products
19
264975-BIM-B-1208
TABLE 9: ELECTRICAL DATA - DL-06 (6-1/2 TON) STANDARD EFFICIENCY W/O PWRD CONV. OUTLET
MCA
Min. Circuit
Supply
Pwr
Pwr
w/Power
Ampacity
Blower
Exh Conv
Electric Heater Actual Heater
Exhaust
Voltage
Motor FLA Motor Outlet
(Amps)
KW Amps
Model No.
(Amps)
RLA
LRA
FLA
1.5
2
1.5
2
1.5
2
FLA FLA
ea.
ea.
ea.
HP
HP
HP
HP
HP
HP
None
--38.0
40.0 43.5 45.5
2TP04520925
6.8
18.9
38.0
40.0 43.5 45.5
12.8 110.0
1.5
6.2
8.2
5.5
0.0
208
2TP04521825
13.5
37.5
54.6
57.1 61.5 64.0
2TP04522425
18
50.0
70.2
72.7 77.1 79.6
2TP04523625
25.5
70.8
96.2
98.7 103.1 105.6
None
--38.0
40.0 43.5 45.5
2TP04520925
9
21.7
38.0
40.0 43.5 45.5
12.8 110.0
1.5
6.2
8.2
5.5
0.0
230
2TP04521825
18
43.3
61.9
64.4 68.8 71.3
2TP04522425
24
57.7
79.9
82.4 86.8 89.3
2TP04523625
34
81.8 110.0 112.5 116.9 119.4
None
--20.7
21.7 22.9 23.9
2TP04520946
9
11.3
20.7
21.7 22.9 23.9
460
7.1
54.0
0.8
3.1
4.1
2.2
0.0
2TP04521846
18
22.6
30.9
32.2 33.7 34.9
2TP04522446
24
30.1
40
41.2 42.7
44
2TP04523646
34
42.7
55
56.2 57.7
59
None
--15.1
16.3 16.9 18.1
2TP04520958
9
9.0
15.1
16.3 16.9 18.1
575
5.1
44.0
0.6
2.4
3.6
1.8
0.0
2TP04521858
18
18.1
24.7
26.2 26.9 28.4
2TP04522458
24
24.1
31.9
33.4 34.1 35.6
2TP04523658
34
34.1
43.9
45.4 46.1 47.6
*
Maximum HACR breaker of the same AMP size is applicable.
Compressors
OD Fan
Motors
Max
Max Fuse* Size
Fuse*
w/Power
Size
Exhaust
(Amps)
(Amps)
1.5
2
1.5
2
HP HP
HP
HP
50 50
50
50
50 50
50
50
60 60
70
70
80 80
80
80
100 100 110
110
50 50
50
50
50 50
50
50
70 70
70
80
80 90
90
90
110 125 125
125
25 25
25
30
25 25
25
30
35 35
35
35
40 45
45
45
60 60
60
60
20 20
20
20
20 20
20
20
25 30
30
30
35 35
35
40
45 50
50
50
TABLE 10: ELECTRICAL DATA - DL-06 (6-1/2 TON) STANDARD EFFICIENCY W/PWRD CONV. OUTLET
MCA
Supply
Pwr
Pwr
Min. Circuit
w/Power
Blower
Ampacity
Exh Conv
Electric Heater Actual Heater
Exhaust
Voltage
Motor FLA Motor Outlet
(Amps)
Model No.
KW Amps
(Amps)
RLA
LRA
FLA
1.5
2
1.5
2
1.5
2
FLA FLA
ea.
ea.
ea.
HP
HP
HP
HP
HP
HP
None
--48.0
50.0 53.5 55.5
2TP04520925
6.8
18.9
48.0
50.0 53.5 55.5
208
12.8 110.0
1.5
6.2
8.2
5.5
10.0
2TP04521825
13.5
37.5
67.1
69.6 74.0 76.5
2TP04522425
18
50.0
82.7
85.2 89.6 92.1
2TP04523625
25.5
70.8 108.7 111.2 115.6 118.1
None
--48.0
50.0 53.5 55.5
2TP04520925
9
21.7
48.0
50.0 54.2 56.7
230
12.8 110.0
1.5
6.2
8.2
5.5
10.0
2TP04521825
18
43.3
74.4
76.9 81.3 83.8
2TP04522425
24
57.7
92.4
94.9 99.3 101.8
2TP04523625
34
81.8 122.5 125.0 129.4 131.9
None
--25.7
26.7 27.9 28.9
2TP04520946
9
11.3
25.7
26.7 27.9 28.9
460
7.1
54.0
0.8
3.1
4.1
2.2
5.0
2TP04521846
18
22.6
37.2
38.4 39.9 41.2
2TP04522446
24
30.1
46.2
47.5
49
50.2
2TP04523646
34
42.7
61.2
62.5
64
65.2
None
--19.1
20.3 20.9 22.1
2TP04520958
9
9.0
19.1
20.3 21.1 22.6
575
5.1
44.0
0.6
2.4
3.6
1.8
4.0
2TP04521858
18
18.1
29.7
31.2 31.9 33.4
2TP04522458
24
24.1
36.9
38.4 39.1 40.6
2TP04523658
34
34.1
48.9
50.4 51.1 52.6
*
Maximum HACR breaker of the same AMP size is applicable.
Compressors
20
OD Fan
Motors
Max
Max Fuse* Size
Fuse*
w/Power
Size
Exhaust
(Amps)
(Amps)
1.5
2
1.5
2
HP HP
HP
HP
60 60
60
60
60 60
60
60
70 70
80
80
90 90
90
100
110 125 125
125
60 60
60
60
60 60
60
60
80 80
90
90
100 100 100
110
125 125 150
150
30 30
30
35
30 30
30
35
40 40
40
45
50 50
50
60
70 70
70
70
20 25
25
25
20 25
25
25
30 35
35
35
40 40
40
45
50 60
60
60
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 11: ELECTRICAL DATA - DU-06 (6-1/2 TON) HIGH EFFICIENCY W/O PWRD CONV. OUTLET
Voltage
OD Fan
Compressors
Motors
RLA
ea.
LRA
ea.
FLA
ea.
Supply
Blower
Motor FLA
1.5
HP
2
HP
Pwr
Pwr
Exh
Conv
Electric Heater Actual Heater
Motor Outlet
KW
Amps
Model No.
FLA
FLA
208
9.0
72.0
1.5
6.2
8.2
5.5
0.0
230
9.0
72.0
1.5
6.2
8.2
5.5
0.0
460
5.8
45.0
0.8
3.1
4.1
2.2
0.0
575
4.5
36.0
0.6
2.4
3.6
1.8
0.0
None
2TP04540925
2TP04541825
2TP04542425
2TP04543625
None
2TP04540925
2TP04541825
2TP04542425
2TP04543625
None
2TP04540946
2TP04541846
2TP04542446
2TP04543646
None
2TP04540958
2TP04541858
2TP04542458
2TP04543658
-6.8
13.5
18
25.5
-9
18
24
34
-9
18
24
34
-9
18
24
34
-18.9
37.5
50.0
70.8
-21.7
43.3
57.7
81.8
-11.3
22.6
30.1
42.7
-9.0
18.1
24.1
34.1
Min. Circuit
Ampacity
(Amps)
1.5
2
HP
HP
29.5
31.5
31.3
33.8
54.6
57.1
70.2
72.7
96.2
98.7
29.5
31.5
34.8
37.3
61.9
64.4
79.9
82.4
110.0 112.5
17.8
18.8
17.8
18.8
30.9
32.2
40
41.2
55
56.2
13.7
14.9
13.8
15.3
24.7
26.2
31.9
33.4
43.9
45.4
Max Fuse Size
MCA
Max Fuse*
w/Power
w/Power
Exhaust
Exhaust Size (Amps)
(Amps)
(Amps)
1.5
2
1.5
2
1.5
2
HP
HP
HP
HP
HP
HP
35.0 37.0
35
40
40
45
38.2 40.7
35
40
40
45
61.5 64.0
60
60
70
70
77.1 79.6
80
80
80
80
103.1 105.6 100 100 110
110
35.0 37.0
35
40
40
45
41.7 44.2
35
40
45
45
68.8 71.3
70
70
70
80
86.8 89.3
80
90
90
90
116.9 119.4 110 125 125
125
20
21
20
20
25
25
20.2 21.4
20
20
25
25
33.7 34.9
35
35
35
35
42.7
44
40
45
45
45
57.7
59
60
60
60
60
15.5 16.7
15
15
20
20
16.1 17.6
15
20
20
20
26.9 28.4
25
30
30
30
34.1 35.6
35
35
35
40
46.1 47.6
45
50
50
50
TABLE 12: ELECTRICAL DATA - DU-06 (6-1/2 TON) HIGH EFFICIENCY W/PWRD CONV. OUTLET
Compressors
Voltage
RLA
ea.
LRA
ea.
OD Fan
Motors
FLA
ea.
Supply
Blower
Motor FLA
1.5
HP
2
HP
Pwr
Pwr
Exh
Conv
Electric Heater Actual Heater
Motor Outlet
KW
Amps
Model No.
FLA
FLA
208
9.0
72.0
1.5
6.2
8.2
5.5
10.0
230
9.0
72.0
1.5
6.2
8.2
5.5
10.0
460
5.8
45.0
0.8
3.1
4.1
2.2
5.0
575
4.5
36.0
0.6
2.4
3.6
1.8
4.0
Johnson Controls Unitary Products
None
2TP04540925
2TP04541825
2TP04542425
2TP04543625
None
2TP04540925
2TP04541825
2TP04542425
2TP04543625
None
2TP04540946
2TP04541846
2TP04542446
2TP04543646
None
2TP04540958
2TP04541858
2TP04542458
2TP04543658
-6.8
13.5
18
25.5
-9
18
24
34
-9
18
24
34
-9
18
24
34
-18.9
37.5
50.0
70.8
-21.7
43.3
57.7
81.8
-11.3
22.6
30.1
42.7
-9.0
18.1
24.1
34.1
Min. Circuit
Ampacity
(Amps)
1.5
2
HP
HP
39.7
41.7
43.8
46.3
67.1
69.6
82.7
85.2
108.7 111.2
39.7
41.7
47.3
49.8
74.4
76.9
92.4
94.9
122.5 125.0
22.8
23.8
23.7
24.9
37.2
38.4
46.2
47.5
61.2
62.5
17.7
18.9
18.8
20.3
29.7
31.2
36.9
38.4
48.9
50.4
Max Fuse Size
MCA
Max Fuse*
w/Power
w/Power
Exhaust
Exhaust Size (Amps)
(Amps)
(Amps)
1.5
2
1.5
2
1.5
2
HP
HP
HP
HP
HP
HP
45.2 47.2
45
50
50
50
50.7 53.2
45
50
60
60
74.0 76.5
70
70
80
80
89.6 92.1
90
90
90
100
115.6 118.1 110 125 125
125
45.2 47.2
45
50
50
50
54.2 56.7
50
50
60
60
81.3 83.8
80
80
90
90
99.3 101.8 100 100 100
110
129.4 131.9 125 125 150
150
25
26
25
25
30
30
26.4 27.7
25
25
30
30
39.9 41.2
40
40
40
45
49
50.2
50
50
50
60
64
65.2
70
70
70
70
19.5 20.7
20
20
20
25
21.1 22.6
20
25
25
25
31.9 33.4
30
35
35
35
39.1 40.6
40
40
40
45
51.1 52.6
50
60
60
60
21
264975-BIM-B-1208
TABLE 13: ELECTRICAL DATA - DL-07 (7-1/2 TON) STANDARD EFFICIENCY W/O PWRD CONV. OUTLET
Compressors
Voltage
208
230
460
575
Supply
OD Fan
Pwr Exh
Blower Motor
Motor
Motors
FLA
RLA
LRA
FLA
ea.
ea.
ea.
11.5
11.5
6.4
5.1
84.0
84.0
42.0
34.0
3.5
3.5
1.6
1.3
2 HP
8.2
8.2
4.1
3.6
3 HP
10.9
10.9
5.3
4.1
FLA
5.5
5.5
2.2
1.8
Pwr
Conv
Outlet
Min. Circuit
Heater Ampacity (Amps)
Amps
Actual
KW
2 HP
3 HP
2 HP
3 HP
None
--
--
41.1
43.8
46.6
49.3
50
50
50
60
2TP04540925
6.8
18.9
41.1
43.8
46.6
49.3
50
50
50
60
2TP04541825
13.5
37.5
57.1
60.5
64.0
67.3
60
70
70
70
2TP04542425
18.0
50.0
72.7
76.1
79.6
83.0
80
80
80
90
2TP04543625
25.5
70.8
98.7
102.1
105.6
109.0
100
110
110
110
FLA
0.0
0.0
0.0
0.0
Max Fuse Size
Max Fuse*
MCA w/Power
w/Power Exhaust
Exhaust (Amps) Size (Amps)
(Amps)
Electric Heater
Model No.
2 HP 3 HP
2 HP
3 HP
None
--
--
41.1
43.8
46.6
49.3
50
50
50
60
2TP04540925
9.0
21.7
41.1
43.8
46.6
49.3
50
50
50
60
2TP04541825
18.0
43.3
64.4
67.8
71.3
74.6
70
70
80
80
2TP04542425
24.0
57.7
82.4
85.8
89.3
92.7
90
90
90
100
2TP04543625
34.0
81.8
112.5
115.9
119.4
122.7
125
125
125
125
None
--
--
21.7
22.9
23.9
25.1
25
25
30
30
2TP04540946
9
11.3
21.7
22.9
23.9
25.1
25
25
30
30
2TP04541846
18
22.6
32.2
33.7
34.9
36.4
35
35
35
40
2TP04542446
24
30.1
41.2
42.7
44
45.5
45
45
45
50
2TP04543646
34
42.7
56.2
57.7
59
60.5
60
60
60
70
None
--
--
17.7
18.2
19.5
20
20
20
20
25
2TP04540958
9
9.0
17.7
18.2
19.5
20
20
20
20
25
2TP04541858
18
18.1
26.2
26.8
28.4
29
30
30
30
30
2TP04542458
24
24.1
33.4
34
35.6
36.2
35
35
40
40
2TP04543658
34
34.1
45.4
46
47.6
48.3
50
50
50
50
TABLE 14: ELECTRICAL DATA - DL-07 (7-1/2 TON) STANDARD EFFICIENCY W/PWRD CONV. OUTLET
Compressors
Voltage
208
230
460
575
22
Supply
OD Fan
Pwr Exh
Blower Motor
Motors
Motor
FLA
RLA
LRA
FLA
ea.
ea.
ea.
11.5
11.5
6.4
5.1
84.0
84.0
42.0
34.0
3.5
3.5
1.6
1.3
2 HP
8.2
8.2
4.1
3.6
3 HP
10.9
10.9
5.3
4.1
FLA
5.5
5.5
2.2
1.8
Pwr
Conv
Outlet
Electric Heater
Model No.
Actual
KW
Min. Circuit
Heater Ampacity (Amps)
Amps
FLA
10.0
10.0
5.0
4.0
2 HP
3 HP
Max Fuse Size
Max Fuse*
MCA w/Power
w/Power Exhaust
Exhaust (Amps) Size (Amps)
(Amps)
2 HP
3 HP
2 HP 3 HP
2 HP
3 HP
None
--
--
51.1
53.8
56.6
59.3
60
60
60
70
2TP04540925
6.8
18.9
51.1
53.8
56.6
59.3
60
60
60
70
2TP04541825
13.5
37.5
69.6
73.0
76.5
79.8
70
80
80
80
2TP04542425
18.0
50.0
85.2
88.6
92.1
95.5
90
90
100
100
2TP04543625
25.5
70.8
111.2
114.6
118.1
121.5
125
125
125
125
None
--
--
51.1
53.8
56.6
59.3
60
60
60
70
2TP04540925
9.0
21.7
51.1
53.8
56.7
60.1
60
60
60
70
2TP04541825
18.0
43.3
76.9
80.3
83.8
87.1
80
90
90
90
2TP04542425
24.0
57.7
94.9
98.3
101.8
105.2
100
100
110
110
2TP04543625
34.0
81.8
125.0
128.4
131.9
135.2
125
150
150
150
None
--
--
26.7
27.9
28.9
30.1
30
30
35
35
2TP04540946
9
11.3
26.7
27.9
28.9
30.1
30
30
35
35
2TP04541846
18
22.6
38.4
39.9
41.2
42.7
40
40
45
45
2TP04542446
24
30.1
47.5
49
50.2
51.7
50
50
60
60
2TP04543646
34
42.7
62.5
64
65.2
66.7
70
70
70
70
None
--
--
21.7
22.2
23.5
24
25
25
25
25
2TP04540958
9
9.0
21.7
22.2
23.5
24
25
25
25
25
2TP04541858
18
18.1
31.2
31.8
33.4
34
35
35
35
35
2TP04542458
24
24.1
38.4
39
40.6
41.2
40
40
45
45
2TP04543658
34
34.1
50.4
51
52.6
53.3
60
60
60
60
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 15: ELECTRICAL DATA - DU-07 (7-1/2 TON) HIGH EFFICIENCY W/O PWRD CONV. OUTLET
Compressors
OD Fan
Motors
Voltage
208
230
460
575
RLA
LRA
FLA
ea.
ea.
ea.
11.5
11.5
5.8
5.1
84.0
84.0
42.0
34.0
1.5
1.5
0.8
0.6
Supply
Blower Motor
FLA
2 HP
8.2
8.2
4.1
3.6
3 HP
10.9
10.9
5.3
4.1
Pwr Exh
Motor
Pwr
Conv
Outlet
FLA
FLA
5.5
5.5
2.2
1.8
0.0
0.0
0.0
0.0
Electric Heater
Model No.
Actual
KW
Heater
Amps
Min. Circuit
Ampacity (Amps)
2 HP
3 HP
MCA w/Power
Exhaust (Amps)
2 HP
3 HP
Max Fuse Size
Max Fuse*
w/Power Exhaust
Size (Amps)
(Amps)
2 HP 3 HP
2 HP
3 HP
None
--
--
37.1
39.8
42.6
45.3
45
50
50
50
2TP04540925
6.8
18.9
37.1
39.8
42.6
45.3
45
50
50
50
2TP04541825
13.5
37.5
57.1
60.5
64.0
67.3
60
70
70
70
2TP04542425
18.0
50.0
72.7
76.1
79.6
83.0
80
80
80
90
2TP04543625
25.5
70.8
98.7
102.1
105.6
109.0
100
110
110
110
None
--
--
37.1
39.8
42.6
45.3
45
50
50
50
2TP04540925
9.0
21.7
37.3
40.7
44.2
47.6
45
50
50
50
2TP04541825
18.0
43.3
64.4
67.8
71.3
74.6
70
70
80
80
2TP04542425
24.0
57.7
82.4
85.8
89.3
92.7
90
90
90
100
2TP04543625
34.0
81.8
112.5
115.9
119.4
122.7
125
125
125
125
None
--
--
18.8
20
21
22.2
20
25
25
25
2TP04540946
9
11.3
18.8
20.2
21.4
22.9
20
25
25
25
2TP04541846
18
22.6
32.2
33.7
34.9
36.4
35
35
35
40
2TP04542446
24
30.1
41.2
42.7
44
45.5
45
45
45
50
2TP04543646
34
42.7
56.2
57.7
59
60.5
60
60
60
70
20
None
--
--
16.3
16.8
18.1
18.6
20
20
20
2TP04540958
9
9.0
16.3
16.8
18.1
18.6
20
20
20
20
2TP04541858
18
18.1
26.2
26.8
28.4
29
30
30
30
30
2TP04542458
24
24.1
33.4
34
35.6
36.2
35
35
40
40
2TP04543658
34
34.1
45.4
46
47.6
48.3
50
50
50
50
TABLE 16: ELECTRICAL DATA - DU-07 (7-1/2 TON) HIGH EFFICIENCY W/PWRD CONV. OUTLET
Compressors
OD Fan
Motors
Voltage
208
230
460
575
RLA
LRA
FLA
ea.
ea.
ea.
11.5
11.5
5.8
5.1
84.0
8 4 .0
42.0
34.0
1.5
1.5
0.8
0.6
Supply
Blower Motor
FLA
2 HP
8.2
8.2
4.1
3.6
3 HP
10.9
10.9
5.3
4.1
Johnson Controls Unitary Products
Pwr Exh
Motor
Pwr
Conv
Outlet
FL A
FL A
5.5
5.5
2.2
1.8
10.0
10.0
5.0
4.0
Electric Heater
Model No.
Actual
KW
Heater
Amps
Min. Circuit
Ampacity (Amps)
2 HP
3 HP
MCA w/Power
Exhaust (Amps)
2 HP
3 HP
Max Fuse Size
Max Fuse*
w/Power Exhaust
Size (Amps)
(Amps)
2 HP 3 HP
2 HP
3 HP
None
--
--
47.1
49.8
52.6
55.3
50
60
60
60
2TP04540925
6.8
18.9
47.1
49.8
53.2
56.6
50
60
60
60
2TP04541825
13.5
37.5
69.6
73.0
76.5
79.8
70
80
80
80
2TP04542425
18.0
50.0
85.2
88.6
92.1
95.5
90
90
100
100
2TP04543625
25.5
70.8
111.2
114.6
118.1
121.5
125
125
125
125
None
--
--
47.1
49.8
52.6
55.3
50
60
60
60
2TP04540925
9.0
21.7
49.8
53.2
56.7
60.1
50
60
60
70
2TP04541825
18.0
43.3
76.9
80.3
83.8
87.1
80
90
90
90
2TP04542425
24.0
57.7
94.9
98.3
101.8
105.2
100
100
110
110
2TP04543625
34.0
81.8
125.0
128.4
131.9
135.2
125
150
150
150
None
--
--
23.8
25
26
27.2
25
30
30
30
2TP04540946
9
11.3
24.9
26.4
27.7
29.2
25
30
30
30
2TP04541846
18
22.6
38.4
39.9
41.2
42.7
40
40
45
45
2TP04542446
24
30.1
47.5
49
50.2
51.7
50
50
60
60
2TP04543646
34
42.7
62.5
64
65.2
66.7
70
70
70
70
None
--
--
20.3
20.8
22.1
22.6
25
25
25
25
2TP04540958
9
9.0
20.3
21
22.6
23.2
25
25
25
25
2TP04541858
18
18.1
31.2
31.8
33.4
34
35
35
35
35
2TP04542458
24
24.1
38.4
39
40.6
41.2
40
40
45
45
2TP04543658
34
34.1
50.4
51
52.6
53.3
60
60
60
60
23
264975-BIM-B-1208
TABLE 17: ELECTRICAL DATA - DL-08 (8-1/2 TON) STANDARD EFFICIENCY W/O PWRD CONV. OUTLET
Compressors
Voltage
208
230
460
575
OD Fan
Motors
RLA
LRA
FLA
ea.
ea.
ea.
11.7
11.7
6.4
5.1
88.0
88.0
42.0
36.0
3.5
3.5
1.6
1.3
Supply Blower Pwr Exh
Motor FLA
Motor
3 HP
10.9
10.9
5.3
4.1
3 HP
10.9
10.9
5.3
4.1
FLA
5.5
5.5
2.2
1.8
Pwr
Conv
Outlet
MCA w/Power
Exhaust
(Amps)
Min. Circuit
Ampacity
(Amps)
Max Fuse*
Size (Amps)
Max Fuse Size
w/Power
Exhaust
(Amps)
Electric Heater
Model No.
Actual
KW
Heater
Amps
3 HP
3 HP
3 HP
3 HP
3 HP
3 HP
3 HP
3 HP
0.0
None
2TP04540925
2TP04541825
2TP04542425
2TP04543625
-6.8
13.5
18
25.5
-18.9
37.5
50.0
70.8
44.2
44.2
60.5
76.1
102.1
44.2
44.2
60.5
76.1
102.1
49.7
49.7
67.3
83.0
109.0
49.7
49.7
67.3
83.0
109.0
50
50
70
80
110
50
50
70
80
110
60
60
70
90
110
60
60
70
90
110
0.0
None
2TP04540925
2TP04541825
2TP04542425
2TP04543625
-9
18
24
34
-21.7
43.3
57.7
81.8
44.2
44.2
67.8
85.8
115.9
44.2
44.2
67.8
85.8
115.9
50.4
50.4
74.6
92.7
122.7
50.4
50.4
74.6
92.7
122.7
50
50
70
90
125
50
50
70
90
125
60
60
80
100
125
60
60
80
100
125
0.0
None
2TP04540946
2TP04541846
2TP04542446
2TP04543646
-9
18
24
34
-11.3
22.6
30.1
42.7
22.9
22.9
33.7
42.7
57.7
22.9
22.9
33.7
42.7
57.7
25.1
25.1
36.4
45.5
60.5
25.1
25.1
36.4
45.5
60.5
25
25
35
45
60
25
25
35
45
60
30
30
40
50
70
30
30
40
50
70
0.0
None
2TP04540958
2TP04541858
2TP04542458
2TP04543658
-9
18
24
34
-9.0
18.1
24.1
34.1
18.2
18.2
26.8
34
46
18.2
18.2
26.8
34
46
20
20
29
36.2
48.3
20
20
29
36.2
48.3
20
20
30
35
50
20
20
30
35
50
25
25
30
40
50
25
25
30
40
50
FLA
TABLE 18: ELECTRICAL DATA - DL-08 (8-1/2 TON) STANDARD EFFICIENCY W/PWRD CONV. OUTLET
Compressors
OD Fan
Motors
Supply Blower Pwr Exh
Motor FLA
Motor
Voltage
208
230
460
575
24
RLA
LRA
FLA
ea.
ea.
ea.
11.7
11.7
6.4
5.1
88.0
88.0
42.0
36.0
3.5
3.5
1.6
1.3
3 HP
10.9
10.9
5.3
4.1
3 HP
10.9
10.9
5.3
4.1
FLA
5.5
5.5
2.2
1.8
Pwr
Conv
Outlet
Electric Heater
Model No.
Actual
KW
Heater
Amps
FLA
10.0
10.0
10.0
10.0
Min. Circuit
Ampacity
(Amps)
3 HP
MCA w/Power
Exhaust
(Amps)
3 HP
3 HP
3 HP
Max Fuse*
Size (Amps)
3 HP
3 HP
Max Fuse Size
w/Power
Exhaust
(Amps)
3 HP
3 HP
None
--
--
54.2
54.2
59.7
59.7
60
60
70
70
2TP04540925
6.8
18.9
54.2
54.2
59.7
59.7
60
60
70
70
2TP04541825
13.5
37.5
73.0
73.0
79.8
79.8
80
80
80
80
2TP04542425
18
50.0
88.6
88.6
95.5
95.5
90
90
100
100
2TP04543625
25.5
70.8
114.6
114.6
121.5
121.5
125
125
125
125
None
--
--
54.2
54.2
59.7
59.7
60
60
70
70
2TP04540925
9
21.7
54.2
54.2
59.7
59.7
60
60
70
70
2TP04541825
18
43.3
80.3
80.3
87.1
87.1
90
90
90
90
2TP04542425
24
57.7
98.3
98.3
105.2
105.2
100
100
110
110
2TP04543625
34
81.8
128.4
128.4
135.2
135.2
150
150
150
150
None
--
--
27.9
27.9
30.1
30.1
30
30
35
35
2TP04540946
9
11.3
27.9
27.9
30.1
30.1
30
30
35
35
2TP04541846
18
22.6
39.9
39.9
42.7
42.7
40
40
45
45
2TP04542446
24
30.1
49
49
51.7
51.7
50
50
60
60
2TP04543646
34
42.7
64
64
66.7
66.7
70
70
70
70
None
--
--
22.2
22.2
24
24
25
25
25
25
2TP04540958
9
9.0
22.2
22.2
24
24
25
25
25
25
2TP04541858
18
18.1
31.8
31.8
34
34
35
35
35
35
2TP04542458
24
24.1
39
39
41.2
41.2
40
40
45
45
2TP04543658
34
34.1
51
51
53.3
53.3
60
60
60
60
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 19: ELECTRICAL DATA - DU-08 (8-1/2 TON) HIGH EFFICIENCY W/O PWRD CONV. OUTLET
Compressors
Voltage
208
230
460
575
OD Fan
Motors
RLA
LRA
FLA
ea.
ea.
ea.
11.7
11.7
6.4
5.1
88.0
88.0
42.0
36.0
3.5
3.5
1.6
1.3
Supply Blower Pwr Exh
Motor FLA
Motor
3 HP
10.9
10.9
5.3
4.1
3 HP
10.9
10.9
5.3
4.1
FLA
5.5
5.5
2.2
1.8
Pwr
Conv
Outlet
Electric Heater
Model No.
Actual
KW
Heater
Amps
FLA
Min. Circuit
Ampacity
(Amps)
MCA w/Power
Exhaust
(Amps)
Max Fuse*
Size (Amps)
Max Fuse Size
w/Power
Exhaust
(Amps)
3 HP
3 HP
3 HP
3 HP
3 HP
3 HP
3 HP
3 HP
0.0
None
2TP04540925
2TP04541825
2TP04542425
2TP04543625
-6.8
13.5
18
25.5
-18.9
37.5
50.0
70.8
44.2
44.2
60.5
76.1
102.1
44.2
44.2
60.5
76.1
102.1
49.7
49.7
67.3
83.0
109.0
49.7
49.7
67.3
83.0
109.0
50
50
70
80
110
50
50
70
80
110
60
60
70
90
110
60
60
70
90
110
0.0
None
2TP04540925
2TP04541825
2TP04542425
2TP04543625
-9
18
24
34
-21.7
43.3
57.7
81.8
44.2
44.2
67.8
85.8
115.9
44.2
44.2
67.8
85.8
115.9
50.4
50.4
74.6
92.7
122.7
50.4
50.4
74.6
92.7
122.7
50
50
70
90
125
50
50
70
90
125
60
60
80
100
125
60
60
80
100
125
0.0
None
2TP04540946
2TP04541846
2TP04542446
2TP04543646
-9
18
24
34
-11.3
22.6
30.1
42.7
22.9
22.9
33.7
42.7
57.7
22.9
22.9
33.7
42.7
57.7
25.1
25.1
36.4
45.5
60.5
25.1
25.1
36.4
45.5
60.5
25
25
35
45
60
25
25
35
45
60
30
30
40
50
70
30
30
40
50
70
0.0
None
2TP04540958
2TP04541858
2TP04542458
2TP04543658
-9
18
24
34
-9.0
18.1
24.1
34.1
18.2
18.2
26.8
34
46
18.2
18.2
26.8
34
46
20
20
29
36.2
48.3
20
20
29
36.2
48.3
20
20
30
35
50
20
20
30
35
50
25
25
30
40
50
25
25
30
40
50
TABLE 20: ELECTRICAL DATA - DU-08 (8-1/2 TON) HIGH EFFICIENCY W/PWRD CONV. OUTLET
Compressors
OD Fan
Motors
Supply Blower Pwr Exh
Motor FLA
Motor
Voltage
208
230
460
575
RLA
LRA
FLA
ea.
ea.
ea.
11.7
11.7
6.4
5.1
88.0
88.0
42.0
36.0
3.5
3.5
1.6
1.3
3 HP
10.9
10.9
5.3
4.1
Johnson Controls Unitary Products
3 HP
10.9
10.9
5.3
4.1
FLA
5.5
5.5
2.2
1.8
Pwr
Conv
Outlet
Electric Heater
Model No.
Actual
KW
Heater
Amps
FLA
10.0
10.0
10.0
10.0
Min. Circuit
Ampacity
(Amps)
3 HP
3 HP
MCA w/Power
Exhaust
(Amps)
3 HP
3 HP
Max Fuse*
Size (Amps)
3 HP
3 HP
Max Fuse Size
w/Power
Exhaust
(Amps)
3 HP
3 HP
None
--
--
54.2
54.2
59.7
59.7
60
60
70
70
2TP04540925
6.8
18.9
54.2
54.2
59.7
59.7
60
60
70
70
2TP04541825
13.5
37.5
73.0
73.0
79.8
79.8
80
80
80
80
2TP04542425
18
50.0
88.6
88.6
95.5
95.5
90
90
100
100
2TP04543625
25.5
70.8
114.6
114.6
121.5
121.5
125
125
125
125
None
--
--
54.2
54.2
59.7
59.7
60
60
70
70
2TP04540925
9
21.7
54.2
54.2
59.7
59.7
60
60
70
70
2TP04541825
18
43.3
80.3
80.3
87.1
87.1
90
90
90
90
2TP04542425
24
57.7
98.3
98.3
105.2
105.2
100
100
110
110
2TP04543625
34
81.8
128.4
128.4
135.2
135.2
150
150
150
150
None
--
--
27.9
27.9
30.1
30.1
30
30
35
35
2TP04540946
9
11.3
27.9
27.9
30.1
30.1
30
30
35
35
2TP04541846
18
22.6
39.9
39.9
42.7
42.7
40
40
45
45
2TP04542446
24
30.1
49
49
51.7
51.7
50
50
60
60
2TP04543646
34
42.7
64
64
66.7
66.7
70
70
70
70
None
--
--
22.2
22.2
24
24
25
25
25
25
2TP04540958
9
9.0
22.2
22.2
24
24
25
25
25
25
2TP04541858
18
18.1
31.8
31.8
34
34
35
35
35
35
2TP04542458
24
24.1
39
39
41.2
41.2
40
40
45
45
2TP04543658
34
34.1
51
51
53.3
53.3
60
60
60
60
25
264975-BIM-B-1208
TABLE 21: ELECTRICAL DATA - DL-10 (10 TON) STANDARD EFFICIENCY W/O PWRD CONV. OUTLET
Supply
Pwr
Min. Circuit
Pwr
Blower
Ampacity
Exh Conv
Electric Heater Actual Heater
Voltage
Motor FLA Motor Outlet
(Amps)
KW
Amps
Model No.
RLA
LRA
FLA
2
3
2
3
FLA
FLA
ea.
ea.
ea.
HP
HP
HP
HP
None
--51.9
54.6
2TP04521825
13.5
37.5
57.1
60.5
8.2 10.9
5.5
0.0
16.3 150.0
3.5
208
2TP04522425
18
50.0
72.7
76.1
2TP04523625
25.5
70.8
98.7 102.1
2TP04525425
40.6
112.7 151.1 154.5
None
--51.9
54.6
2TP04521825
18
43.3
64.4
67.8
16.3 150.0
3.5
8.2 10.9
5.5
0.0
230
2TP04522425
24
57.7
82.4
85.8
2TP04523625
34
81.8 112.5 115.9
2TP04525425
129.9 140.2 143.5
54
None
--33.2
34.4
2TP04521846
18
22.6
33.2
34.4
11.5
75.0
1.6
4.1
5.3
2.2
0.0
460
2TP04522446
24
30.1
41.2
42.7
2TP04523646
34
42.7
56.2
57.7
2TP04525446
54
67.8
70.1
71.6
None
--22.2
22.7
2TP04521858
18
18.1
26.2
26.8
7.1
62.0
1.3
3.6
4.1
1.8
0.0
575
2TP04522458
24
24.1
33.4
34
2TP04523658
34
34.1
45.4
46
2TP04525458
54
54.2
56.5
57.1
Maximum HACR breaker of the same AMP size is applicable.
*
OD Fan
Compressors
Motors
MCA
w/Power
Exhaust
(Amps)
2
3
HP
HP
57.4 60.1
64.0 67.3
79.6 83.0
105.6 109.0
158.0 161.4
57.4 60.1
71.3 74.6
89.3 92.7
119.4 122.7
147.0 150.4
35.4 36.6
35.4 36.6
44
45.5
59
60.5
72.8 74.3
24
24.5
28.4
29
35.6 36.2
47.6 48.3
58.7 59.3
Max
Max Fuse* Size
Fuse*
w/Power
Size
Exhaust
(Amps)
(Amps)
2
3
2
3
HP HP
HP
HP
60 70
70
70
60 70
70
70
80 80
80
90
100 110
110
110
175 175
175
175
60 70
70
70
70 70
80
80
90 90
90
100
125 125
125
125
150 175
175
175
40 45
45
45
40 45
45
45
45 45
45
50
60 60
60
70
80 80
80
80
25 25
30
30
30 30
30
30
35 35
40
40
50 50
50
50
70 70
70
70
TABLE 22: ELECTRICAL DATA - DL-10 (10 TON) STANDARD EFFICIENCY W/PWRD CONV. OUTLET
Supply
Pwr
Pwr
Blower
Exh Conv
Electric Heater Actual Heater
Voltage
Motor FLA Motor Outlet
KW
Model No.
Amps
RLA
LRA
FLA
2
3
FLA
FLA
ea.
ea.
ea.
HP
HP
None
--2TP04521825
13.5
37.5
16.3 150.0
3.5
8.2 10.9
5.5
10.0
208
2TP04522425
18
50.0
2TP04523625
25.5
70.8
2TP04525425
40.6
112.7
None
--2TP04521825
18
43.3
16.3 150.0
3.5
8.2 10.9
5.5
10.0
230
2TP04522425
24
57.7
2TP04523625
34
81.8
2TP04525425
129.9
54
None
--2TP04521846
18
22.6
11.5
75.0
1.6
4.1
5.3
2.2
5.0
460
2TP04522446
24
30.1
2TP04523646
34
42.7
2TP04525446
54
67.8
None
--2TP04521858
18
18.1
7.1
62.0
1.3
3.6
4.1
1.8
4.0
575
2TP04522458
24
24.1
2TP04523658
34
34.1
2TP04525458
54
54.2
*
Maximum HACR breaker of the same AMP size is applicable.
Compressors
26
OD Fan
Motors
Min. Circuit
Ampacity
(Amps)
2
HP
61.9
69.6
85.2
111.2
163.6
61.9
76.9
94.9
125.0
152.7
38.2
38.4
47.5
62.5
76.3
26.2
31.2
38.4
50.4
61.5
3
HP
64.6
73.0
88.6
114.6
167.0
64.6
80.3
98.3
128.4
156.0
39.4
39.9
49
64
77.8
26.7
31.8
39
51
62.1
MCA
w/Power
Exhaust
(Amps)
2
3
HP
HP
67.4 70.1
76.5 79.8
92.1 95.5
118.1 121.5
170.5 173.9
67.4 70.1
83.8 87.1
101.8 105.2
131.9 135.2
159.5 162.9
40.4 41.6
41.2 42.7
50.2 51.7
65.2 66.7
79.1 80.6
28
28.5
33.4
34
40.6 41.2
52.6 53.3
63.7 64.3
Max
Max Fuse* Size
Fuse*
w/Power
Size
Exhaust
(Amps)
(Amps)
2
3
2
3
HP HP
HP
HP
70 80
80
80
70 80
80
80
90 90
100
100
125 125
125
125
175 175
175
175
70 80
80
80
80 90
90
90
100 100
110
110
125 150
150
150
175 175
175
175
45 50
50
50
45 50
50
50
50 50
60
60
70 70
70
70
90 90
90
90
30 30
35
35
35 35
35
35
40 40
45
45
60 60
60
60
70 70
70
70
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 23: ELECTRICAL DATA - DU-10 (10 TON) HIGH EFFICIENCY W/O PWRD CONV. OUTLET
Supply
Pwr
Min. Circuit
Pwr
Blower
Ampacity
Exh Conv
Electric Heater Actual Heater
Voltage
Motor FLA Motor Outlet
(Amps)
KW
Amps
Model No.
RLA
LRA
FLA
2
3
2
3
FLA
FLA
ea.
ea.
ea.
HP
HP
HP
HP
None
--51.2
53.9
2TP04521825
13.5
37.5
57.1
60.5
8.2 10.9
5.5
0.0
16.0 137.0
3.5
208
2TP04522425
18
50.0
72.7
76.1
2TP04523625
25.5
70.8
98.7 102.1
2TP04525425
40.6
112.7 151.1 154.5
None
--51.2
53.9
2TP04521825
18
43.3
64.4
67.8
16.0 137.0
3.5
8.2 10.9
5.5
0.0
230
2TP04522425
24
57.7
82.4
85.8
2TP04523625
34
81.8 112.5 115.9
54
2TP04525425
129.9 140.2 143.5
None
--26
27.2
2TP04521846
18
22.6
32.2
33.7
8.3
69.0
1.6
4.1
5.3
2.2
0.0
460
2TP04522446
24
30.1
41.2
42.7
2TP04523646
34
42.7
56.2
57.7
2TP04525446
54
67.8
70.1
71.6
None
--20.6
21.1
2TP04521858
18
18.1
26.2
26.8
6.4
58.0
1.3
3.6
4.1
1.8
0.0
575
2TP04522458
24
24.1
33.4
34
2TP04523658
34
34.1
45.4
46
2TP04525458
54
54.2
56.5
57.1
Maximum HACR breaker of the same AMP size is applicable.
*
Compressors
OD Fan
Motors
MCA
w/Power
Exhaust
(Amps)
2
3
HP
HP
56.7 59.4
64.0 67.3
79.6 83.0
105.6 109.0
158.0 161.4
56.7 59.4
71.3 74.6
89.3 92.7
119.4 122.7
147.0 150.4
28.2 29.4
34.9 36.4
44
45.5
59
60.5
72.8 74.3
22.4 22.9
28.4
29
35.6 36.2
47.6 48.3
58.7 59.3
Max
Max Fuse* Size
Fuse*
w/Power
Size
Exhaust
(Amps)
(Amps)
2
3
2
3
HP HP
HP
HP
60 60
70
70
60 70
70
70
80 80
80
90
100 110
110
110
175 175
175
175
60 60
70
70
70 70
80
80
90 90
90
100
125 125
125
125
150 175
175
175
30 35
35
35
35 35
35
40
45 45
45
50
60 60
60
70
80 80
80
80
25 25
25
25
30 30
30
30
35 35
40
40
50 50
50
50
70 70
70
70
TABLE 24: ELECTRICAL DATA - DU-10 (10 TON) HIGH EFFICIENCY W/PWRD CONV. OUTLET
Supply
Pwr
Pwr
Blower
Exh Conv
Electric Heater Actual Heater
Voltage
Motor FLA Motor Outlet
KW
Model No.
Amps
RLA
LRA
FLA
2
3
FLA
FLA
ea.
ea.
ea.
HP
HP
None
--2TP04521825
13.5
37.5
16.0 137.0
3.5
8.2 10.9
5.5
10.0
208
2TP04522425
18
50.0
2TP04523625
25.5
70.8
2TP04525425
40.6
112.7
None
--2TP04521825
18
43.3
3.5
8.2 10.9
5.5
10.0
16.0 137.0
230
2TP04522425
24
57.7
2TP04523625
34
81.8
54
2TP04525425
129.9
None
--2TP04521846
18
22.6
8.3
69.0
1.6
4.1
5.3
2.2
5.0
460
2TP04522446
24
30.1
2TP04523646
34
42.7
2TP04525446
54
67.8
None
--2TP04521858
18
18.1
6.4
58.0
1.3
3.6
4.1
1.8
4.0
575
2TP04522458
24
24.1
2TP04523658
34
34.1
2TP04525458
54
54.2
*
Maximum HACR breaker of the same AMP size is applicable.
Compressors
OD Fan
Motors
Johnson Controls Unitary Products
Min. Circuit
Ampacity
(Amps)
2
HP
61.2
69.6
85.2
111.2
163.6
61.2
76.9
94.9
125.0
152.7
31
38.4
47.5
62.5
76.3
24.6
31.2
38.4
50.4
61.5
3
HP
63.9
73.0
88.6
114.6
167.0
63.9
80.3
98.3
128.4
156.0
32.2
39.9
49
64
77.8
25.1
31.8
39
51
62.1
MCA
w/Power
Exhaust
(Amps)
2
3
HP
HP
66.7 69.4
76.5 79.8
92.1 95.5
118.1 121.5
170.5 173.9
66.7 69.4
83.8 87.1
101.8 105.2
131.9 135.2
159.5 162.9
33.2 34.4
41.2 42.7
50.2 51.7
65.2 66.7
79.1 80.6
26.4 26.9
33.4
34
40.6 41.2
52.6 53.3
63.7 64.3
Max
Max Fuse* Size
Fuse*
w/Power
Size
Exhaust
(Amps)
(Amps)
2
3
2
3
HP HP
HP
HP
70 70
80
80
70 80
80
80
90 90
100
100
125 125
125
125
175 175
175
175
70 70
80
80
80 90
90
90
100 100
110
110
125 150
150
150
175 175
175
175
35 40
40
40
40 40
45
45
50 50
60
60
70 70
70
70
90 90
90
90
30 30
30
30
35 35
35
35
40 40
45
45
60 60
60
60
70 70
70
70
27
264975-BIM-B-1208
TABLE 25: ELECTRICAL DATA - DL-12 (12-1/2 TON) STANDARD EFFICIENCY W/O PWRD CONV. OUTLET
Max
MCA
Max
Min. Circuit
Supply
Pwr
Pwr
w/Power
Fuse
Fuse*
Ampacity
Blower
Exh Conv
Electric Heater Actual Heater
Exhaust
Size
Size
Voltage
(Amps)
Motor FLA Motor Outlet
Amps
KW
Model No.
(Amps)
(Amps) w/Power
RLA
LRA
FLA
3
5
3
5
3
5
3
5
3
5
FLA
FLA
Max
MCA
Max
ea.
ea.
ea.
HP
HP
HP Circuit
HP
HP
HP HP HP HP HP
Min.
Supply
Pwr
Pwr
w/Power
OD Fan
Fuse*
Fuse
None
--62.9
68.1 68.4 73.6 80 80 80 90
Compressors
Ampacity
Blower
Exh Conv
Electric Heater Actual Heater
Exhaust
Motors
Size
Size
13.5
37.5
62.9
68.1 68.4 73.8 80 80 80 90
Voltage
(Amps)
Motor FLA Motor Outlet 2TP04521825
KW
Amps
Model No.
(Amps)
(Amps) w/Power
20.0 146.0
3.5
10.9 16.1
5.5
0.0
208
2TP04522425
18
50.0
76.1 82.6 83.0 89.5 80 90 90 90
RLA
LRA
FLA
3
5
3
5
3
5
3
5
3
5
2TP04523625
25.5
70.8 102.1 108.6 109.0 115.5 110 110 110 125
FLA
FLA
ea.
ea.
ea.
HP
HP
HP 161.0
HP 161.4
HP 167.9
HP 175
HP 175
HP 175
HP 175
HP
2TP04525425
40.6
112.7 154.5
None
--62.9 68.1
68.1 68.4
68.4 73.6
73.6 80
80 80
80 80
80 90
90
None
--62.9
2TP04521825
13.5
37.5
62.9
68.1
68.4
73.8
80
80
80
90
2TP04521825
18
43.3
67.8 74.3 74.6 81.1 80 80 80 90
20.0 146.0
146.0
3.5
10.9 16.1
16.1
5.5
0.0
208
2TP04522425
18
50.0
76.1 92.3
82.6 92.7
83.0 99.2
89.5 90
80 100
90 100
90 100
90
20.0
3.5
10.9
5.5
0.0
230
2TP04522425
24
57.7
85.8
2TP04523625
25.5
70.8
102.1
108.6 122.7
109.0 129.2
115.5 125
110 125
110 125
110 150
125
2TP04523625
34
81.8 115.9 122.4
2TP04525425
40.6 129.9
112.7 143.5
154.5 150.0
161.0 150.4
161.4 156.9
167.9 175
175 175
175 175
175 175
175
2TP04525425
54
None
--62.9
None
--27.4 68.1
30.2 68.4
29.6 73.6
32.4 80
35 80
35 80
35 90
40
2TP04521825
18
43.3
67.8
2TP04521846
18
22.6
33.7 74.3
37.2 74.6
36.4 81.1
39.9 80
35 80
40 80
40 90
40
20.0
146.0
3.5
10.9
5.5
0.0
230
2TP04522425
24
57.7
85.8
8.4
73.0
1.6
5.3 16.1
8.1
2.2
0.0
460
2TP04522446
24
30.1
42.7 92.3
46.2 92.7
45.5 99.2
49 90
45 100
50 100
50 100
50
2TP04523625
34
81.8 115.9
2TP04523646
34
42.7
57.7 122.4
61.2 122.7
60.5 129.2
64 125
60 125
70 125
70 150
70
2TP04525425
129.9
143.5
150.0
150.4
156.9
175
175
175
175
54
2TP04525446
54
67.8
71.6 75.1 74.3 77.8 80 90 80 90
None
--27.4 23.7
30.2 23.6
29.6 25.5
32.4 25
35 30
35 30
35 30
40
None
--21.8
2TP04521846
18
22.6
33.7 29.2
37.2 36.4
39.9 30
35 30
40 30
40 35
40
2TP04521858
18
18.1
26.8
29
31.4
8.4
73.0
1.6
5.3
8.1
2.2
0.0
460
2TP04522446
24
30.1
42.7
46.2 36.2
45.5 38.6
49
45 40
50 40
50 40
50
6.7
60.0
1.3
4.1
6.0
1.8
0.0
575
2TP04522458
24
24.1
34
36.4
35
2TP04523646
34
42.7
57.7
61.2
60.5
64
60
70
70
70
2TP04523658
34
34.1
46
48.4 48.3 50.6 50 50 50 60
2TP04525446
54
67.8
71.6 59.5
75.1 59.3
74.3 61.7
77.8 70
80 70
90 70
80 70
90
2TP04525458
54
54.2
57.1
--21.8 23.7 23.6 25.5 25 30 30 30
*
Maximum HACR breaker of the same AMP size is applicable. None
Compressors
OD Fan
Motors
TABLE 26: ELECTRICAL DATA - DL-12 (12-1/2 TON) STANDARD EFFICIENCY W/PWRD CONV. OUTLET
MCA
Max
Min. Circuit
Supply
Pwr
Pwr
w/Power
Fuse*
Ampacity
Blower
Exh Conv
Electric Heater Actual Heater
Exhaust
Size
Voltage
(Amps)
Motor FLA Motor Outlet
KW
Amps
Model No.
(Amps)
(Amps)
RLA
LRA
FLA
3
5
3
5
3
5
3
5
FLA
FLA
ea.
ea.
ea.
HP
HP
HP
HP
HP
HP HP HP
None
--72.9 78.1 78.4 83.6 90 90
2TP04521825
13.5
37.5
73.0 79.5 79.8 86.3 90 90
20.0 146.0
3.5
10.9 16.1
5.5
10.0
208
2TP04522425
18
50.0
88.6 95.1 95.5 102.0 90 100
2TP04523625
25.5
70.8 114.6 121.1 121.5 128.0 125 125
2TP04525425
40.6
112.7 167.0 173.5 173.9 180.4 175 175
None
--72.9 78.1 78.4 83.6 90 90
2TP04521825
18
43.3
80.3 86.8 87.1 93.6 90 90
20.0 146.0
3.5
10.9 16.1
5.5
10.0
230
2TP04522425
24
57.7
98.3 104.8 105.2 111.7 100 110
2TP04523625
34
81.8 128.4 134.9 135.2 141.7 150 150
2TP04525425
129.9 156.0 162.5 162.9 169.4 175 175
54
None
--32.4 35.2 34.6 37.4 40 40
2TP04521846
18
22.6
39.9 43.4 42.7 46.2 40 45
8.4
73.0
1.6
5.3
8.1
2.2
5.0
460
2TP04522446
24
30.1
49
52.5 51.7 55.2 50 60
2TP04523646
34
42.7
64
67.5 66.7 70.2 70 70
2TP04525446
54
67.8
77.8 81.3 80.6 84.1 90 90
None
--25.8 27.7 27.6 29.5 30 30
2TP04521858
18
18.1
31.8 34.2
34
36.4 35 35
6.7
60.0
1.3
4.1
6.0
1.8
4.0
575
2TP04522458
24
24.1
39
41.4 41.2 43.6 40 45
2TP04523658
34
34.1
51
53.4 53.3 55.6 60 60
2TP04525458
54
54.2
62.1 64.5 64.3 66.7 70 70
*
Maximum HACR breaker of the same AMP size is applicable.
OD Fan
Compressors
Motors
28
Max
Fuse
Size
w/Power
3
5
HP HP
90 100
90 100
100 110
125 150
175 200
90 100
90 100
110 125
150 150
175 175
40 45
45 50
60 60
70 80
90 90
30 35
35 40
45 45
60 60
70 70
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 27: ELECTRICAL DATA - DU-12 (12-1/2 TON) HIGH EFFICIENCY W/O PWRD CONV. OUTLET
Compressors
Voltage
RLA
ea.
208
230
460
575
*
LRA
ea.
OD Fan
Motors
FLA
ea.
Supply
Blower
Motor FLA
3
HP
5
HP
Pwr
Pwr
Exh Conv
Electric Heater
Motor Outlet
Model No.
FLA
Actual Heater
KW
Amps
FLA
None
2TP04521825
18.9 146.0
3.5
10.9 16.1
5.5
0.0
2TP04522425
2TP04523625
2TP04525425
None
2TP04521825
18.9 146.0
3.5
10.9 16.1
5.5
0.0
2TP04522425
2TP04523625
2TP04525425
None
2TP04521846
9.5
73.0
1.6
5.3
8.1
2.2
0.0
2TP04522446
2TP04523646
2TP04525446
None
2TP04521858
7.6
58.4
1.3
4.1
6.0
1.8
0.0
2TP04522458
2TP04523658
2TP04525458
Maximum HACR breaker of the same AMP size is applicable.
-13.5
18
25.5
40.6
-18
24
34
54
-18
24
34
54
-18
24
34
54
-37.5
50.0
70.8
112.7
-43.3
57.7
81.8
129.9
-22.6
30.1
42.7
67.8
-18.1
24.1
34.1
54.2
Min. Circuit
Ampacity
(Amps)
3
HP
60.4
60.5
76.1
102.1
154.5
60.4
67.8
85.8
115.9
143.5
29.9
33.7
42.7
57.7
71.6
23.8
26.8
34
46
57.1
5
HP
65.6
67.0
82.6
108.6
161.0
65.6
74.3
92.3
122.4
150.0
32.7
37.2
46.2
61.2
75.1
25.7
29.2
36.4
48.4
59.5
MCA
w/Power
Exhaust
(Amps)
3
5
HP
HP
65.9 71.1
67.3 73.8
83.0 89.5
109.0 115.5
161.4 167.9
65.9 71.1
74.6 81.1
92.7 99.2
122.7 129.2
150.4 156.9
32.1 34.9
36.4 39.9
45.5
49
60.5
64
74.3 77.8
25.6 27.5
29
31.4
36.2 38.6
48.3 50.6
59.3 61.7
Max
Max Fuse* Size
Fuse *
w/Power
Size
Exhaust
(Amps)
(Amps)
3
5
3
5
HP HP
HP
HP
70 80
80
90
70 80
80
90
80 90
90
90
110 110 110
125
175 175 175
175
70 80
80
90
70 80
80
90
90 100 100
100
125 125 125
150
175 175 175
175
35 40
40
40
35 40
40
40
45 50
50
50
60 70
70
70
80 90
80
90
30 30
30
35
30 30
30
35
35 40
40
40
50 50
50
60
70 70
70
70
TABLE 28: ELECTRICAL DATA - DU-12 (12-1/2 TON) HIGH EFFICIENCY W/PWRD CONV. OUTLET
Compressors
Voltage
RLA
ea.
208
230
460
575
*
LRA
ea.
OD Fan
Motors
FLA
ea.
Supply
Blower
Motor FLA
3
HP
5
HP
Pwr
Pwr
Exh Conv
Electric Heater
Motor Outlet
Model No.
FLA
FLA
None
2TP04521825
18.9 146.0
3.5
10.9 16.1
5.5
10.0
2TP04522425
2TP04523625
2TP04525425
None
2TP04521825
18.9 146.0
3.5
10.9 16.1
5.5
10.0
2TP04522425
2TP04523625
2TP04525425
None
2TP04521846
9.5
73.0
1.6
5.3
8.1
2.2
5.0
2TP04522446
2TP04523646
2TP04525446
None
2TP04521858
7.6
58.4
1.3
4.1
6.0
1.8
4.0
2TP04522458
2TP04523658
2TP04525458
Maximum HACR breaker of the same AMP size is applicable.
Johnson Controls Unitary Products
Actual Heater
KW
Amps
-13.5
18
25.5
40.6
-18
24
34
54
-18
24
34
54
-18
24
34
54
-37.5
50.0
70.8
112.7
-43.3
57.7
81.8
129.9
-22.6
30.1
42.7
67.8
-18.1
24.1
34.1
54.2
Min. Circuit
Ampacity
(Amps)
3
HP
70.4
73.0
88.6
114.6
167.0
70.4
80.3
98.3
128.4
156.0
34.9
39.9
49
64
77.8
27.8
31.8
39
51
62.1
5
HP
75.6
79.5
95.1
121.1
173.5
75.6
86.8
104.8
134.9
162.5
37.7
43.4
52.5
67.5
81.3
29.7
34.2
41.4
53.4
64.5
MCA
w/Power
Exhaust
(Amps)
3
5
HP
HP
75.9 81.1
79.8 86.3
95.5 102.0
121.5 128.0
173.9 180.4
75.9 81.1
87.1 93.6
105.2 111.7
135.2 141.7
162.9 169.4
37.1 39.9
42.7 46.2
51.7 55.2
66.7 70.2
80.6 84.1
29.6 31.5
34
36.4
41.2 43.6
53.3 55.6
64.3 66.7
Max Fuse* Size
Max
w/Power
Fuse *
Exhaust
Size
(Amps)
(Amps)
3
5
3
5
HP HP
HP
HP
80 90
90
100
80 90
90
100
90 100 100
110
125 125 125
150
175 175 175
200
80 90
90
100
90 90
90
100
100 110 110
125
150 150 150
150
175 175 175
175
40 45
45
45
40 45
45
50
50 60
60
60
70 70
70
80
90 90
90
90
35 35
35
35
35 35
35
40
40 45
45
45
60 60
60
60
70 70
70
70
29
264975-BIM-B-1208
TABLE 29: DL PHYSICAL DATA
Models
Component
Evaporator
Blower
-06
-07
-08
-10
-12
Blower, Centrifugal (Dia X Wd. In)
15 x 15
12 x 12
12 X 12
15 x 15
15 x 15
Motor, Standard (HP)
1-1/2
2
3
2
3
Motor, Optional (HP)
2
3
3
3
5
Evaporator
Coil
Condenser
Fan
(2 per Unit)
2
2
3
2
3
15
15
15
15
15
Height (in.)
30
32
32
40
40
Face Area (ft2)
9.9
10.67
10.67
13.2
13.2
Propeller Dia. (in.)
24
24
24
24
24
Motor (HP each)
1/3
3/4
3/4
3/4
3/4
CFM, Nominal (each)
3400
4400
4400
4400
4400
Condenser
Coil
(2 per unit)
Refrigerant
Charge
Rows
1
1
1
1
2
Fins per Inch
20
20
20
20
20
Height (in.)
24
28
36
44
44
Face Area (ft2)
7.9
9.33
12
14.5
14.5
System 1 (lb/oz)
4/6
4/10
5/8
6/12
10/12
System 2 (lb/oz)
4/0
3/14
5/2
6/12
11/0
Quantity
2
2
2
2
2
Type
Recip
Recip
Recip.
Recip
Scroll
Size (Wd. X Ht. x Thickness in.)
25x20x2
25x16x2
25x16x2
25x20x2
25x20x2
Number Per Unit
4
4
4
4
4
Compressors
Air Filters
Rows
Fins per Inch
TABLE 30: DU PHYSICAL DATA
Models
Component
Evaporator
Blower
Evaporator
Coil
Condenser
Fan
(2 per Unit)
-06
-07
-08
-10
-12
Blower, Centrifugal (Dia. X Wd.
in.)
12 x 12
12 x 12
12 X 12
15 x 15
15 x 15
Motor, Standard (HP)
1-1/2
2
3
2
3
Motor, Optional (HP)
2
3
3
3
5
Rows
3
3
3
4
4
Fins per Inch
15
15
15
15
15
Height (in.)
32
32
32
40
40
Face Area (ft.2 each)
10.67
10.67
10.67
13.2
13.2
Propeller Dia.
(in., each)
24
24
24
24
24
Motor (HP, each)
1/3
1/3
3/4
3/4
3/4
CFM, Nominal (each)
3400
3400
4400
4400
4400
2
2
2
2
Rows (each)
Condenser
Coil
(2 per unit)
Refrigerant
Charge
Compressors
Air Filters
30
Sys 1: 2 Row
Sys 2: 1 Row
Fins per Inch
20
20
20
20
20
Height (in., each)
36
36
36
44
44
Face Area (ft.2 each)
12
12
12
14.5
14.5
System 1 (lb./oz.)
8/0
8/12
9/8
12/0
9/14
System 2 (lb./oz.)
4/12
9/0
8/2
11/0
9/4
Quantity
2
2
2
2
2
Type
Recip.
Recip
Recip.
Recip
Scroll
Size (Wd. x Ht. x Thickness in.)
25x16x2
25x16x2
25x16x2
25x20x2
25x20x2
Johnson Controls Unitary Products
264975-BIM-B-1208
OPTIONAL ELECTRIC HEAT
GAS PIPING
The factory-installed heaters are wired for single point power
supply. Power supply need only be brought into the single
point terminal block.
Proper sizing of gas piping depends on the cubic feet per
hour of gas flow required, specific gravity of the gas and the
length of run. "National Fuel Gas Code" Z223.1 (in U.S.A.) or
the current Gas Installation Codes CSA-B149.1 (in Canada)
should be followed in all cases unless superseded by local
codes or gas utility requirements. Refer to the Pipe Sizing
Table 33. The heating value of the gas may differ with locality.
The value should be checked with the local gas utility.
These CSA approved heaters are located within the central
compartment of the unit with the heater elements extending
in to the supply air chamber.
Fuses are supplied, where required, by the factory. Some kW
sizes require fuses and others do not. refer to Table 31 for
minimum CFM limitations and to Tables 9 through 28 for electrical data.
TABLE 31: MINIMUM SUPPLY AIR CFM
Heater
kW
Unit Model Size (Nominal Tons)
Voltage
-06 (6.5) -07 (7.5) -08 (8.5) -10 (10) -12 (12.5)
Minimum Supply Air CFM
9
1950
2250
2550
-
-
18
1950
2250
2550
3000
3750
1950
2250
2550
3000
3750
1950
2250
2550
3000
3750
54
-
-
-
3000
3750
9
1950
2250
2550
-
-
18
1950
2250
2550
3000
3750
24
36
24
208/
230
480
1950
2250
2550
3000
3750
36
1950
2250
2550
3000
3750
54
-
-
-
3000
3750
9
1950
2250
2550
-
-
1950
2250
2550
3000
3750
1950
2250
2550
3000
3750
36
1950
2250
2550
3000
3750
54
-
-
-
3000
3750
18
24
600
OPTIONAL GAS HEAT
O P
C O
G U
S H
T IO N A L
IL
A R D
O W N
FIGURE 21 - SIDE ENTRY GAS PIPING
OPTIONAL
COIL
GUARD
SHOWN
These gas-fired heaters have aluminized-steel or optional
stainless steel, tubular heat exchangers with spark ignition.
TABLE 32: GAS APPLICATION DATA
Unit
Size
-06
-07
-08
-10
-12
Input (MBH)
Output (MBH)
Temp Rise
(°F)
120
96
20-50
15
180
144
35-65
10
120
96
15-45
Opt.
10
15
180
144
30-60
10
120
96
15-45
15
180
144
30-60
15
180
144
20-50
20
240
192
30-60
15
180
144
10-40
20
240
192
20-50
Johnson Controls Unitary Products
FIGURE 22 - BOTTOM ENTRY GAS PIPING
31
264975-BIM-B-1208
TABLE 33: GAS PIPE SIZING - CAPACITY OF PIPE
4.
All piping should be cleaned of dirt and scale by hammering on the outside of the pipe and blowing out loose
particles. Before initial start-up, be sure that all gas lines
external to the unit have been purged of air.
5.
The gas supply should be a separate line and installed in
accordance with all safety codes as prescribed under
“Limitations”.
6.
A 1/8-inch NPT plugged tapping, accessible for test gage
connection, must be installed immediately upstream of
the gas supply connection to the unit.
7.
After the gas connections have been completed, open
the main shut-off valve admitting normal gas pressure to
the mains. Check all joints for leaks with soap solution or
other material suitable for the purpose. NEVER USE A
FLAME.
Nominal Iron Pipe Size
Length of
Pipe (ft.)
3/4 in.
1 in.
1-1/4 in.
10
278
520
1050
20
190
350
730
30
152
285
590
40
130
245
500
50
115
215
440
60
105
195
400
70
96
180
370
80
90
170
350
90
84
160
320
100
79
150
305
NOTE: Maximum capacity of pipe in cubic feet of gas per
hour based upon a pressure drop of 0.3 inch W.C.
and 0.6 specific gravity gas.
NOTE: There may be a local gas utility requirement specifying a minimum diameter for gas piping. All units
require a 3/4 inch pipe connection at the entrance
fitting. Line should not be sized smaller than the
entrance fitting size.
GAS CONNECTION
The gas supply line can be routed within the space and roof
curb, exiting through the unit’s basepan. Refer to Figure 9 for
the gas piping inlet location. Typical supply piping arrangements are shown in Figures 21 and 22. All pipe nipples, fittings, and the gas cock are field supplied or may be
purchased in UP accessory kit #1GP0405.
Gas piping recommendations:
1.
A drip leg and a ground joint union must be installed in
the gas piping.
2.
Where required by local codes, a manual shut-off valve
must be installed outside of the unit.
3.
Use wrought iron or steel pipe for all gas lines. Pipe dope
should be applied sparingly to male threads only.
Natural gas may contain some propane. Propane is
an excellent solvent and will quickly dissolve white
lead and most standard commercial compounds. A
special pipe dope must be used when assembling
wrought iron or steel pipe. Shellac based compounds such as Gaskolac or Stalastic, and compounds such as Rectorseal #5, Clydes’s or John
Crane may be used.
32
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly could
result in serious injury, death or property damage.
Never test for gas leaks with an open flame. use a
commercially available soap solution made specifically for the detection of leaks to check all connections. A fire or explosion may result causing property
damage, personal injury or loss of life.
The furnace and its individual shut-off valve must be
disconnected from the gas supply piping system
during any pressure testing at pressures in excess
of 1/2 PSIG.
Pressures greater than 1/2 PSIG will cause gas
valve damage resulting in a hazardous condition. If it
is subjected to a pressure greater than 1/2 PSIG, the
gas valve must be replaced.
The furnace must be isolated from the gas supply
piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less
than 1/2 PSIG.
Threaded joints should be coated with a sealing
compound that is resistant to the action of liquefied
petroleum gases. Do not use Teflon tape.
Johnson Controls Unitary Products
264975-BIM-B-1208
LP UNITS, TANKS AND PIPING
All gas heat units are shipped from the factory equipped for
natural gas use only. The unit may be converted in the field
for use with LP gas with accessory kit model number
1NP0442.
All LP gas equipment must conform to the safety standards of
the National Fire Protection Association.
For satisfactory operation, LP gas pressure must be 10.5
inch W.C. at the unit under full load. Maintaining proper gas
pressure depends on three main factors:
1.
The vaporization rate which depends on the temperature
of the liquid and the “wetted surface” area of the container(s).
2.
The proper pressure regulation. (Two-stage regulation is
recommended).
3.
The pressure drop in the lines between regulators and
between the second stage regulator and the appliance.
Pipe size required will depend on the length of the pipe
run and the total load of all appliances.
Complete information regarding tank sizing for vaporization,
recommended regulator settings, and pipe sizing is available
from most regulator manufacturers and LP gas suppliers.
LP gas is an excellent solvent and will quickly dissolve white
lead and most standard commercial compounds. A special
pipe dope must be used when assembling wrought iron or
steel pipe for LP. Shellac base compounds such as Gaskolac
or Stalastic, and compounds such as Rectorseal #5, Clyde’s,
or John Crane may be used.
Check all connections for leaks when piping is completed
using a soap solution. NEVER USE A FLAME.
flue exhaust is routed through factory installed exhaust piping
with screen. If necessary, a flue exhaust extension may be
installed at the point of installation.
OPTIONS/ACCESSORIES
ELECTRIC HEAT
Electric heaters are available as factory-installed options or
field-installed accessories. Refer to electric heat instructions
for installation. These heaters mount in the heat compartment
with the heating elements extending into the supply air chamber. All electric heaters are fused and intended for use with
single point power supply.
MOTORIZED OUTDOOR DAMPER
The Motorized Outdoor Damper can be a factory installed
option or a field installed accessory. If factory installed, refer
to the instructions included with the outdoor air hood to complete the assembly. Field installed Motorized Outdoor
Damper accessories include complete instructions for installation.
ECONOMIZER
The Economizer can be a factory installed option or a field
installed accessory. If factory installed, refer to the instructions included with the outdoor air hood to complete the
assembly. Field installed Economizer accessories include
complete instructions for installation.
There are two Economizer options:
1.
Down Flow application with barometric relief hood standard.
2.
Horizontal Flow application that requires the purchase of
a barometric relief hood.
POWER EXHAUST
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly could
result in serious injury, death or property damage.
Never test for gas leaks with an open flame. use a
commercially available soap solution made specifically for the detection of leaks to check all connections. A fire or explosion may result causing property
damage, personal injury or loss of life.
VENT AND COMBUSTION AIR
Venting slots in the heating compartment access panel
remove the need for a combustion air hood. The gas heat
Johnson Controls Unitary Products
The Power Exhaust can be a factory installed option or a field
installed accessory. If factory installed, refer to the instructions included with the outdoor air hood to complete the
assembly. Field installed Power Exhaust accessories include
complete instructions for installation.
The Power Exhaust factory installed option is for Down Flow
application only.
There are two field installed Power Exhaust accessories:
1.
Down Flow application.
2.
Horizontal Flow application that requires the purchase of
a barometric relief hood.
33
264975-BIM-B-1208
RAIN HOOD
All of the hood components, including the filters, the gasketing and the hardware for assembling, are packaged and
located between the condenser coil section and the main unit
cabinet, if the unit has factory installed options. If field
installed accessories are being installed all parts necessary
for the installation comes in the accessory.
ECONOMIZER AND POWER EXHAUST SET POINT
ADJUSTMENTS AND INFORMATION
•
For a single enthalpy operation carefully turn the set
point adjusting screw (found on the damper control module) to the "A", "B", "C" or "D" setting corresponding to
the lettered curve of the Enthalpy Set Point Adjustment
Figure 23.
•
For a dual enthalpy operation, carefully turn the set point
adjusting screw fully clockwise past the "D" setting.
POWER EXHAUST DAMPER SET POINT (WITH OR WITHOUT POWER EXHAUST)
•
With no power exhaust option, adjust the Exhaust Air
Adjustment Screw fully clockwise. This will allow 2nd
stage cooling to operate.
•
With power exhaust option, each building pressurization
requirement will be different. The point at which the
power exhaust comes on is determined by the economizer damper position (Percent Open). The Exhaust Air
Adjustment Screw should be set at the Percent Open of
the economizer damper at which the power exhaust is
needed. It can be set from 0 to 100% damper open.
Remove the top rear access panel from the unit. Locate the
economizer control module, where the following adjustments
will be made.
Extreme care must be exercised in turning all set
point, maximum and minimum damper positioning
adjustment screws to prevent twisting them off.
INDOOR AIR QUALITY AQ
MINIMUM POSITION ADJUSTMENT
•
Check that the damper blades move smoothly without
binding; carefully turn the Minimum Position Adjust
screw (found on the damper control module) fully clockwise and then set the thermostat indoor fan switch to the
ON position and then OFF or energize and de-energize
terminals “R” to “G”.
•
With the thermostat set to the indoor fan ON position or
terminals “R” to “G” energized, turn the Minimum Position Adjusting screw (located on the damper control
module) counterclockwise until the desired minimum
damper position has been attained.
ENTHALPY SET POINT ADJUSTMENT
The enthalpy set point may now be set by selecting the
desired set point shown in the Enthalpy Set Point Adjustment
Figure 23. Adjust as follows:
Indoor Air Quality (indoor sensor input): Terminal AQ accepts
a +2 to +10 Vdc signal with respect to the (AQ1) terminal.
When the signal is below it's set point, the actuator is allowed
to modulate normally in accordance with the enthalpy and
mixed air sensor inputs. When the AQ signal exceeds it's set
point setting and there is no call for free cooling, the actuator
is proportionately modulated from the 2 to 10 Vdc signal, with
2 Vdc corresponding to full closed and 10 Vdc corresponding
to full open. When there is no call for free cooling, the damper
position is limited by the IAQ Max damper position setting.
When the signal exceeds it's set point (Demand Control Ventilation Set Point) setting and there is a call for free cooling,
the actuator modulates from the minimum position to the full
open position based on the highest call from either the mixed
air sensor input or the AQ voltage input.
•
Optional CO2 Space Sensor Kit Part # 2AQ04700324
•
Optional CO2 Sensor Kit Part # 2AQ04700424
Replace the top rear access panel on the unit.
34
Johnson Controls Unitary Products
264975-BIM-B-1208
CONTROL
CURVE
CONTROL POINT
APPROX. 0F (0C)
AT 50% RH
A
73 (23)
B
C
70 (21)
67 (19)
D
63 (17)
85 90 95 100 105 110
(29) (32) (35) (38) (41) (43)
80
(27)
75
(24)
70
(21)
65
(18)
60
(16)
55
(13)
50
(10)
45
(7)
35
(2)
A
B
C
D
40
(4)
B A
D C
35
(2)
40 45 50 55 60 65 70 75 80 85 90 95 100 105 110
(4) (7) (10) (13) (16) (18) (21) (24) (27) (29) (32) (35) (38) (41) (43)
APPROXIMATE DRY BULB TEMPERATURE - 0F (0C)
FIGURE 23 - ENTHALPY SET POINT CHART
Exhaust Air
Adjustment
Screw
Exhaust Air LED
Damper Min.
Position
Screw
Indoor Air Quality
Max. Adjustment
Screw
N1
N
EXH
Set
TR
P1
P
EXH
24
Vac
HOT
T1
T
Min
Pos
IAQ
Max
Indoor Air Quality
LED
AQ1
AQ
IAQ
SO
IAQ
Min
TR1
24
Vac
COM
+
1
2
5
Indoor Air Quality
Min. Adjustment
Screw
Free Cooling LED
SO+
3
4
EF
EF1
Free
Cool
SR+
SR
B
A
C
D
Economizer Enthalpy
Set Point Adjustment
Screw
FIGURE 24 - HONEYWELL ECONOMIZER CONTROL W7212
Johnson Controls Unitary Products
35
264975-BIM-B-1208
PHASING
A
DL/DU units are properly phased at the factory. Check for
proper compressor rotation. If the blower or compressors
rotate in the wrong direction at start-up, the electrical connection to the unit is misphased. Change the phasing of the Field
Line Connection at the factory or field supplied disconnect to obtain proper rotation. (Scroll compressors operate in
only one direction. If the scroll is drawing low amperage, has
similar suction and discharge pressures, or producing a high
noise level, the scroll is misphased.)
A
C*
* NEVER LOOSEN
A
B
SPAN LENGTH
Scroll compressors require proper rotation to operate correctly. Units are properly phased at the factory. Do not change the internal wiring to make the
blower condenser fans, or compressor rotate correctly.
DEFL. FORCE
BLOWER ROTATION
Check for proper supply air blower rotation. If the blower is
rotating backwards, the line voltage at the unit point of power
connection is misphased (See ‘PHASING’).
FIGURE 25 - BELT ADJUSTMENT
TABLE 34: SUPPLY AIR LIMITATIONS
Unit Size
Minimum
Maximum
-06
1950
3250
-07
2250
3750
-08
2550
4250
-10
3000
5000
-12
3750
6250
BELT TENSION
The tension on the belt should be adjusted as shown in Figure 25.
Procedure for adjusting belt tension:
1.
2.
3.
4.
Loosen six nuts (top and bottom) A.
Adjust by turning (B).
Never loosen nuts (C).
Use belt tension checker to apply a perpendicular
force to one belt at the midpoint of the span as
shown. Deflection distance of 4mm (5/32”) is
obtained.
To determine the deflection distance from normal
position, use a straight edge from sheave to sheave
as reference line. The recommended deflection
force is as follows:
Tension new belts at the max. deflection force recommended for the belt section. Check the belt tension at least two times during the first 24 hours of
operation. Any retensioning should fall between the
min. and max. deflection force values.
5. After adjusting retighten nuts (A).
36
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 35: DL-06 (6-1/2 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
1
2
3
4
5
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
0.2
-
-
-
-
-
-
3291
1191
1.28
3096
1059
1.14
2963
948
1.02
2757
831
0.89
0.4
-
-
-
3168
1225
1.31
2969
1085
1.16
2658
939
1.01
2535
834
0.89
2255
718
0.77
0.6
3223
1273
1.37
2732
1084
1.16
2500
947
1.02
2110
803
0.86
1923
699
0.75
1608
596
0.64
0.8
2541
1091
1.17
2168
925
0.99
1882
793
0.85
-
-
-
-
-
-
-
-
-
1.0
1859
908
0.97
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
TABLE 36: DL-06 (6-1/2 TON) OPTIONAL MOTOR DOWN SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
1
2
3
4
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
5
BHP
CFM
W5
BHP
0.4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3489
1553
1.67
0.6
-
-
-
-
-
-
-
-
-
-
-
-
3394
1641
1.76
3101
1407
1.51
0.8
-
-
-
-
-
-
3623
2009
2.15
3323
1742
1.87
2971
1477
1.58
2607
1241
1.33
1.0
-
-
-
3643
2150
2.31
3224
1820
1.95
2889
1569
1.68
2466
1306
1.40
2009
1071
1.15
1.2
3613
2238
2.40
3143
1917
2.06
2748
1621
1.74
2369
1385
1.49
1879
1141
1.22
-
-
-
1.4
3099
2039
2.19
2636
1711
1.83
2195
1424
1.53
-
-
-
-
-
-
-
-
-
1.6
2586
1833
1.97
2124
1532
1.64
-
-
-
-
-
-
-
-
-
-
-
-
1.8
2073
1621
1.74
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
Johnson Controls Unitary Products
37
264975-BIM-B-1208
TABLE 37: DU-06 (6-1/2 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE1,2
ESP3
0.2
0.4
0.6
0.8
1.0
1.2
CFM
–
3320
3020
2700
2300
1781
0 Turns
W5
RPM
–
–
1126 1650
1129 1530
1132 1380
1136 1230
1120 1010
BHP
–
1.77
1.64
1.48
1.32
1.08
CFM
3310
3050
2780
2450
2003
–
1 Turn
W5
RPM
1079 1590
1082 1440
1086 1320
1088 1180
1091 1010
–
–
BHP
1.71
1.54
1.42
1.27
1.08
–
CFM
3190
2850
2550
2160
1570
–
TURNS OPEN4
2 Turns
5
RPM W
BHP CFM
1035 1410 1.51 3005
1038 1290 1.38 2680
1040 1150 1.23 2320
1043 1010 1.08 1879
1047 820 0.88
–
–
–
–
–
3 Turns
5
RPM W
991 1230
992 1100
996 980
998 840
–
–
–
–
BHP
1.32
1.18
1.05
0.90
–
–
CFM
2780
2480
2055
1500
–
–
4 Turns
5
RPM W
945 1070
946 970
948 840
952 700
–
–
–
–
BHP
1.15
1.04
0.90
0.75
–
–
CFM
2560
2200
1925
–
–
–
5 Turns
5
RPM W
897 940
899 840
902 720
–
–
–
–
–
–
BHP
1.01
0.90
0.77
–
–
–
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
6-1/2 TON STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE
1.4
External Static ("WC)
1.2
1
0.8
0.6
0.4
0 Turns
0.2
0
1500
5 Turns
1700
1900
2100
2300
2500
4 Turns
2700
3 Turns
2900
2 Turns
3100
1 Turn
3300
3500
CFM
38
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 38: DU-06 (6-1/2 TON) OPTIONAL MOTOR DOWN SHOT BLOWER PERFORMANCE1,2
ESP3
0.2
0.4
0.6
0.8
1
1.2
1.4
CFM
–
–
3281
3031
2765
2493
2284
0 Turns
5
RPM W
–
–
–
–
1259 2140
1262 1970
1268 1810
1273 1700
1278 1520
BHP
–
–
2.3
2.1
1.9
1.8
1.6
CFM
–
3343
3123
2875
2595
2228
1690
1 Turn
5
RPM W
–
–
1207 2040
1212 1910
1215 1760
1220 1630
1225 1420
1231 1170
BHP
–
2.2
2.0
1.9
1.7
1.5
1.3
CFM
3426
3155
2912
2651
2300
1916
–
TURNS OPEN4
2 Turns
5
RPM W BHP CFM
1156 1940 2.1 3300
1160 1780 1.9 3014
1164 1650 1.8 2757
1167 1500 1.6 2449
1171 1360 1.5 2051
1176 1160 1.2 1323
–
–
–
–
3 Turns
5
RPM W
1108 1700
1111 1590
1114 1460
1116 1320
1120 1170
1126 880
–
–
BHP
1.8
1.7
1.6
1.4
1.2
0.9
–
4 Turns
5
RPM W
1057 1500
1059 1380
1062 1240
1065 1090
1069 950
–
–
–
–
CFM
3081
2800
2514
2148
1715
–
–
BHP
1.6
1.5
1.3
1.2
1.0
–
–
CFM
2889
2600
2287
1868
–
–
–
5 Turns
5
RPM W
1004 1300
1007 1170
1008 1050
1012 900
–
–
–
–
–
–
BHP
1.4
1.3
1.1
1.0
–
–
–
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
6-1/2 TON OPTIONAL MOTOR DOWN SHOT BLOWER PERFORMANCE
1.6
1.4
External Static ("WC)
1.2
1
0.8
0.6
0 Turns
0.4
1 Turn
0.2
5 Turns
0
1000
1500
2000
2500
4 Turns
3000
3 turns
2 Turns
3500
4000
CFM
Johnson Controls Unitary Products
39
264975-BIM-B-1208
TABLE 39: DL, DU-07 (7-1/2 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE
4
TURNS OPEN
3
ESP
0.2
0.4
0.6
0.8
1
1.2
CFM
3619
3343
3100
2846
2559
2219
0 Turns
5
RPM W
1203 2148
1204 1988
1205 1857
1205 1712
1207 1574
1209 1435
BHP
2.3
2.1
2.0
1.8
1.7
1.5
CFM
3452
3189
2944
2675
2335
1935
1 Turn
5
RPM W
1156 1913
1159 1781
1162 1676
1166 1534
1169 1364
1174 1039
BHP
2.1
1.9
1.8
1.6
1.5
1.1
CFM
3272
2995
2746
2448
2084
-
2 Turns
5
RPM W
1110 1696
1113 1547
1116 1440
1118 1326
1119 1174
-
BHP
1.8
1.7
1.5
1.4
1.3
-
CFM
3085
2798
2512
2162
1712
-
3 Turns
5
RPM W
1063 1503
1065 1360
1068 1246
1071 1098
1074 941
-
BHP
1.6
1.5
1.3
1.2
1.0
-
CFM
2932
2640
2340
1956
-
4 Turns
5
RPM W
1013 1299
1014 1190
1017 1067
1020 934
-
BHP
1.4
1.3
1.1
1.0
-
5 Turns
5
CFM RPM W
2742 963 1123
2421 965 1024
2084 967 918
1606 969 781
-
BHP
1.2
1.1
1.0
0.8
-
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
7-1/2 TON STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE
1.4
External Static (”WC)
1.2
1
0.8
0.6
0.4
0.2
0
1500
5 Turns
2000
2500
4 Turns
3 Turns
3000
2 Turns
1 Turn
0 Turns
3500
CFM
40
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 40: DL, DU-07 (7-1/2 TON) OPTIONAL MOTOR DOWNSHOT BLOWER PERFORMANCE
ESP3
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
CFM
3995
3718
3506
3290
3065
2799
2401
1940
0 Turns
5
RPM W
1299 2790
1303 2580
1305 2440
1308 2290
1312 2167
1315 1977
1320 1775
1325 1514
BHP
3.0
2.8
2.6
2.5
2.3
2.1
1.9
1.6
CFM
3765
3508
3288
3053
2795
2458
2098
-
1 Turn
5
RPM W
1249 2420
1252 2290
1255 2117
1258 1982
1261 1844
1264 1675
1269 1487
-
BHP
2.6
2.5
2.3
2.1
2.0
1.8
1.6
-
CFM
3619
3353
3107
2858
2558
2223
-
TURNS OPEN4
2 Turns
5
RPM W BHP CFM
1198 2147 2.3 3399
1201 2010 2.2 3131
1203 1862 2.0 2876
1206 1712 1.8 2594
1209 1602 1.7 2259
1212 1408 1.5 1780
-
3 Turns
5
RPM W
1144 1849
1147 1715
1149 1603
1152 1487
1155 1318
1159 1084
-
BHP
2.0
1.8
1.7
1.6
1.4
1.2
-
CFM
3223
2945
2666
2334
1954
-
4 Turns
5
RPM W
1092 1630
1094 1525
1096 1368
1099 1248
1101 1095
-
BHP
1.7
1.6
1.5
1.3
1.2
-
CFM
3002
2715
2418
2049
-
5 Turns
5
RPM W
1038 1421
1039 1328
1042 1206
1044 1037
-
BHP
1.5
1.4
1.3
1.1
-
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
7-1/2 TON OPTIONAL MOTOR DOWN SHOT BLOWER PERFORMANCE
1.8
1.6
External Static ("WC)
1.4
1.2
1
0.8
0.6
0.4
0.2
5 Turns
0
1700
2200
2700
4 Turns
3200
3 Turns
2 Turns
3700
1 Turn
0 Turns
4200
CFM
Johnson Controls Unitary Products
41
264975-BIM-B-1208
TABLE 41: DL, DU-08 (8-1/2 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE
4
3
ESP
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
CFM
3995
3718
3506
3290
3065
2799
2401
1940
0 Turns
5
RPM W
1299 2790
1303 2580
1305 2440
1308 2290
1312 2167
1315 1977
1320 1775
1325 1514
BHP
3.0
2.8
2.6
2.5
2.3
2.1
1.9
1.6
CFM
3765
3508
3288
3053
2795
2458
2098
-
1 Turn
5
RPM W
1249 2420
1252 2290
1255 2117
1258 1982
1261 1844
1264 1675
1269 1487
-
BHP
2.6
2.5
2.3
2.1
2.0
1.8
1.6
-
CFM
3619
3353
3107
2858
2558
2223
-
TURNS OPEN
2 Turns
5
RPM W BHP CFM
1198 2147 2.3 3399
1201 2010 2.2 3131
1203 1862 2.0 2876
1206 1712 1.8 2594
1209 1602 1.7 2259
1212 1408 1.5 1780
-
3 Turns
5
RPM W
1144 1849
1147 1715
1149 1603
1152 1487
1155 1318
1159 1084
-
BHP
2.0
1.8
1.7
1.6
1.4
1.2
-
CFM
3223
2945
2666
2334
1954
-
4 Turns
5
RPM W
1092 1630
1094 1525
1096 1368
1099 1248
1101 1095
-
BHP
1.7
1.6
1.5
1.3
1.2
-
CFM
3002
2715
2418
2049
-
5 Turns
5
RPM W
1038 1421
1039 1328
1042 1206
1044 1037
-
BHP
1.5
1.4
1.3
1.1
-
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
8-1/2 TON STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE
1.8
1.6
External Static ("WC)
1.4
1.2
1
0.8
0.6
0.4
0.2
5 Turns
0
1700
2200
2700
4 Turns
3200
3 Turns
2 Turns
3700
1 Turn
0 Turns
4200
CFM
42
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 42: DL, DU-08 (8-1/2 TON) OPTIONAL DRIVE DOWN SHOT BLOWER PERFORMANCE
ESP3
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
CFM
4073
3841
3627
3404
3182
2935
2615
2294
1808
0 Turns
5
RPM W
1346 2930
1351 2910
1354 2800
1358 2570
1362 2540
1367 2290
1371 2150
1375 2010
1382 1390
BHP
3.1
3.1
3.0
2.8
2.7
2.5
2.3
2.2
1.5
CFM
3897
3632
3425
3226
2975
2685
2409
1970
–
1 Turn
5
RPM W
1296 2700
1301 2470
1304 2360
1308 2230
1312 2030
1317 2000
1319 1690
1325 1430
–
–
BHP
2.9
2.6
2.4
2.4
2.2
2.1
1.8
1.5
–
CFM
3732
3460
3267
3047
2778
2462
2106
–
–
TURNS OPEN4
2 Turns
5
RPM W BHP CFM
1245 2390 2.6 3598
1248 2270 2.4 3324
1251 2090 2.2 3085
1254 2000 2.1 2820
1257 1790 1.9 2478
1261 1630 1.7 2160
1265 1470 1.6 1407
–
–
–
–
–
–
–
–
3 Turns
5
RPM W
1191 2100
1194 1930
1197 1800
1200 1670
1203 1550
1206 1380
1213 1000
–
–
–
–
BHP
2.2
2.1
1.9
1.8
1.7
1.5
1.0
–
–
CFM
3445
3168
2904
2585
2241
1729
–
–
–
4 Turns
5
RPM W
1136 1800
1138 1680
1141 1550
1144 1490
1147 1270
1151 1040
–
–
–
–
–
–
BHP
2.0
1.8
1.7
1.6
1.4
1.1
–
–
–
CFM
3209
2922
2638
2258
1811
–
–
–
–
5 Turns
5
RPM W
1078 1600
1081 1470
1082 1370
1085 1260
1088 1110
–
–
–
–
–
–
–
–
BHP
1.8
1.6
1.5
1.4
1.2
–
–
–
–
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
8-1/2 TON OPTIONAL DRIVE DOWN SHOT BLOWER PERFORMANCE
2
1.8
External Static ("WC)
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
5 Turns 4 Turns 3 Turns 2 Turns 1 Turn
0
1000
1500
2000
2500
3000
3500
4000
0 Turns
4500
CFM
Johnson Controls Unitary Products
43
264975-BIM-B-1208
TABLE 43: DL, DU-10 (10 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
1
2
3
4
5
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
0.2
-
-
-
-
-
-
-
-
-
3896
1639
1.76
3688
1453
1.56
3447
1268
1.36
0.4
4040
2076
2.23
4005
1934
2.07
3790
1698
1.82
3569
1508
1.62
3333
1330
1.43
3057
1147
1.23
0.6
3890
2006
2.15
3697
1790
1.92
3427
1550
1.66
3152
1356
1.45
-
-
-
-
-
-
0.8
3620
1882
2.02
3324
1629
1.75
2972
1380
1.48
-
-
-
-
-
-
-
-
-
1.0
3227
1708
1.83
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
TABLE 44: DL, DU-10 (10 TON) OPTIONAL MOTOR DOWN SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
CFM
W
0.4
4965
0.6
4876
0.8
1
5
BHP
CFM
W
3485
3.74
4875
3416
3.66
4651
4713
3291
3.53
1.0
4476
3116
1.2
4165
1.4
3779
1.6
3319
44
2
5
BHP
CFM
W
3150
3.38
4613
2997
3.21
4359
4387
2823
3.03
3.34
4084
2632
2898
3.11
3741
2646
2.84
3359
2372
2.54
-
3
5
4
5
BHP
CFM
W5
BHP
2106
2.26
3907
1860
1.99
1966
2.11
3590
1724
1.85
3541
1827
1.96
3242
1584
1.70
2.03
3197
1691
1.81
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
BHP
CFM
W
2739
2.94
4322
2582
2.77
4038
4077
2417
2.59
2.82
3768
2245
2427
2.60
3432
2212
2.37
3069
-
-
-
5
BHP
CFM
W
2374
2.55
4156
2220
2.38
3860
3719
2059
2.21
2.41
3365
1892
2070
2.22
-
1895
2.03
-
-
-
-
5
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 45: DL, DU-12 (12-1/2 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
1
2
3
4
5
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
0.4
5078
3630
3.89
4809
3103
3.33
4594
3053
3.27
4360
2478
2.66
4090
2093
2.24
3812
1798
1.93
0.6
4865
3456
3.71
4584
2961
3.17
4349
2912
3.12
4106
2318
2.49
3814
1964
2.11
-
-
-
0.8
4642
3284
3.52
4356
2828
3.03
4089
2776
2.98
3840
2137
2.29
-
-
-
-
-
-
1.0
4408
3114
3.34
4124
2705
2.90
3815
2647
2.84
-
-
-
-
-
-
-
-
-
1.2
4164
2947
3.16
3889
2592
2.78
-
-
-
-
-
-
-
-
-
-
-
-
1.4
3910
2787
2.99
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
TABLE 46: DL, DU-12 (12-1/2 TON) OPTIONAL MOTOR DOWN SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
1
2
3
4
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
5
BHP
CFM
W5
BHP
0.4
5994
5400
5.79
5565
4369
4.69
5488
4169
4.47
5264
3599
3.86
4990
3085
3.31
4738
2812
3.02
0.6
5824
5216
5.59
5368
4186
4.49
5289
3991
4.28
5049
3437
3.69
4763
2937
3.15
4491
2655
2.85
0.8
5641
5022
5.39
5170
4012
4.30
5076
3807
4.08
4822
3272
3.51
4528
2790
2.99
4235
2497
2.68
1.0
5444
4819
5.17
4971
3846
4.12
4847
3618
3.88
4584
3103
3.33
4286
2644
2.83
3969
2340
2.51
1.2
5233
4609
4.94
4771
3687
3.95
4604
3426
3.67
4335
2933
3.15
4035
2499
2.68
-
-
-
1.4
5009
4394
4.71
4571
3537
3.79
4346
3233
3.47
4074
2762
2.96
3777
2356
2.53
-
-
-
1.6
4771
4174
4.48
4370
3395
3.64
4074
3040
3.26
3802
2590
2.78
-
-
-
-
-
-
1.8
4520
3951
4.24
4169
3262
3.50
3786
2850
3.06
-
-
-
-
-
-
-
-
-
2.0
4255
3728
4.00
3966
3137
3.36
-
-
-
-
-
-
-
-
-
-
-
-
2.2
3976
3505
3.76
3763
3020
3.24
-
-
-
-
-
-
-
-
-
-
-
-
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
Johnson Controls Unitary Products
45
264975-BIM-B-1208
TABLE 47: DL-06 (6-1/2 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
1
2
3
4
5
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
0.4
-
-
-
-
-
-
3367
1216
1.30
3133
1067
1.14
2954
944
1.01
2701
819
0.88
0.6
-
-
-
3208
1239
1.33
2913
1068
1.15
2466
913
0.98
2350
789
0.85
1750
621
0.67
0.8
-
-
-
2651
1058
1.13
2317
894
0.96
1656
700
0.75
-
-
-
-
-
-
1.0
2186
998
1.07
1774
830
0.89
-
-
-
-
-
-
-
-
-
-
-
-
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
TABLE 48: DL-06 (6-1/2 TON) OPTIONAL MOTOR SIDE SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
CFM
W
0.6
-
0.8
1
5
BHP
CFM
W
-
-
-
-
-
-
1.0
-
-
-
1.2
-
-
1.4
-
1.6
1.8
46
2
5
3
5
BHP
CFM
W
BHP
CFM
W
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3327
1866
-
-
3270
1971
2.11
2537
3196
2077
2.23
2460
1651
1.77
2426
1768
1.90
-
-
-
4
5
BHP
CFM
W
-
-
-
5
5
BHP
CFM
W5
BHP
-
3597
1598
1.71
-
-
-
3503
1689
1.81
3172
1430
1.53
3406
1778
1.91
3032
1497
1.61
2248
1143
1.23
2.00
2926
1578
1.69
2160
1217
1.31
-
-
-
1544
1.66
2043
1296
1.39
-
-
-
-
-
-
1858
1318
1.41
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 49: DU-06 (6-1/2 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE
ESP3
0.2
0.4
0.6
0.8
1
1.2
1.4
CFM
–
–
–
2866
2611
2300
1918
0 Turns
5
RPM W
–
–
–
–
–
–
1117 1600
1122 1470
1126 1340
1131 1180
BHP
–
–
–
1.7
1.6
1.4
1.3
CFM
–
–
2974
2724
2417
2070
–
1 Turn
5
RPM W
–
–
–
–
1071 1530
1075 1420
1079 1300
1083 1160
–
–
BHP
–
–
1.6
1.5
1.4
1.2
–
CFM
3278
3007
2749
2465
2133
1702
–
TURNS OPEN4
2 Turns
3 Turns
4 Turns
5
5
5
RPM W BHP CFM RPM W BHP CFM RPM W
1021 1540 1.7 3146 980 1370 1.5 2963 936 1200
1025 1430 1.5 2865 982 1280 1.4 2673 939 1100
1029 1320 1.4 2585 986 1170 1.3 2371 941 980
1032 1220 1.3 2278 989 1050 1.1 2020 944 890
1036 1100 1.2 1907 992 940 1.0 1542 947 760
1040 950 1.0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
BHP
1.3
1.2
1.1
1.0
0.8
–
–
CFM
2792
2483
2154
1745
–
–
–
5 Turns
5
RPM W
892 1040
893 940
894 850
896 750
–
–
–
–
–
–
BHP
1.1
1.0
0.9
0.8
–
–
–
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
6-1/2 TON STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE
1.6
External Static ("WC)
1.4
1.2
1
0.8
0 Turns
0.6
1 Turn
0.4
0.2
0
1500
5 Turns
1700
1900
2100
2300
2500
2700
4 Turns
2900
3 Turns
2 Turns
3100
3300
3500
CFM
Johnson Controls Unitary Products
47
264975-BIM-B-1208
TABLE 50: DU-06 (6-1/2 TON) OPTIONAL MOTOR SIDE SHOT BLOWER PERFORMANCE
(63
&)0
±
±
±
±
±
7XUQV
530 :
±
±
±
±
±
±
±
±
±
±
%+3
±
±
±
±
±
&)0
±
±
±
±
7XUQ
530 :
±
±
±
±
±
±
±
±
%+3
±
±
±
±
&)0
±
±
±
7851623(1
7XUQV
530 : %+3 &)0
±
±
±
±
±
±
±
±
±
±
±
±
7XUQV
530 :
±
±
±
±
±
±
%+3
±
±
±
&)0
±
±
±
±
7XUQV
530 :
±
±
±
±
±
±
±
±
%+3
±
±
±
±
&)0
±
±
±
±
±
7XUQV
530 :
±
±
±
±
±
±
±
±
±
±
%+3
±
±
±
±
±
%ORZHUSHUIRUPDQFHIRUJDVKHDWLQFOXGHVPD[LPXPQXPEHURIKHDWWXEHVDYDLODEOHIRUHDFKWRQQDJH
%ORZHUSHUIRUPDQFHLQFOXGHVWZRLQFKWKURZDZD\ILOWHUV
(63([WHUQDO6WDWLF3UHVVXUHJLYHQLVWKDWDYDLODEOHIRUWKHVXSSO\DQGUHWXUQDLUGXFWV\VWHP$OOLQWHUQDOUHVLVWDQFHVKDYHEHHQ
GHGXFWHGIURPWKHWRWDOVWDWLFSUHVVXUHRIWKHEORZHU
³7XUQV2SHQ´UHIHUVWRWKHVHWWLQJRIWKHYDULDEOHSLWFKPRWRUVKHDYHZKHUH³7XUQV2SHQ´LVIXOO\FORVHG
: :DWWV
721237,21$/027256,'(6+27%/2:(53(5)250$1&(
( [ W H U Q D O 6 WD W L F : & 7XUQV
7XUQ
7XUQV
7XUQV
7XUQV
7XUQV
&)0
48
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 51: DL, DU-07 (7-1/2 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE
ESP3
CFM
3309
3058
2809
2580
0.2
0.4
0.6
0.8
1
1.2
1.4
0 Turns
5
RPM W
BHP
1202 2058 2.2
1206 1899 2.0
1209 1793 1.9
1212 1701 1.8
CFM
3439
3178
2918
2645
2340
1 Turn
5
RPM W
BHP
1152 1996 2.1
1156 1847 2.0
1159 1714 1.8
1162 1595 1.7
1165 1455 1.6
CFM
3721
3446
3198
2922
2649
2333
1951
TURNS OPEN4
2 Turns
3 Turns
5
5
RPM W
BHP CFM RPM W
BHP
1108 1951 2.1 3495 1053 1684 1.8
1104 1831 2.0 3239 1055 1408 1.5
1106 1697 1.8 2964 1057 1456 1.6
1109 1591 1.7 2688 1060 1336 1.4
1111 1453 1.6 2385 1063 1241 1.3
1115 1325 1.4 2002 1066 1114 1.2
1118 1176 1.3
-
CFM
3377
3058
2772
2469
2108
1624
-
4 Turns
5
RPM W
BHP
1006 1520 1.6
1008 1388 1.5
1010 1268 1.4
1012 1177 1.3
1015 1035 1.1
1017 886.2 1.0
-
5 Turns
5
CFM RPM W
BHP
3124 957 1309 1.4
2825 959 1182 1.3
2523 960 1090 1.2
2177 963 975
1.0
1746 965 851
0.9
-
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
7-1/2 TON STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE
1.6
External Static ("WC)
1.4
1.2
1
0.8
0 Turns
0.6
1 Turn
0.4
0.2
5 Turns
0
1500
2000
2500
3000
4 Turns
3 Turns
2 Turns
3500
CFM
Johnson Controls Unitary Products
49
264975-BIM-B-1208
TABLE 52: DL, DU-07 (7-1/2 TON) OPTIONAL SIDE SHOT BLOWER PERFORMANCE
ESP3
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
CFM
4467
4216
4001
3804
3603
3370
3185
2928
2678
2326
0 Turns
5
RPM W
1295 3131
1299 3018
1301 2861
1304 2729
1308 2598
1310 2435
1312 2327
1315 2173
1319 2055
1354 1844
BHP
3.4
3.2
3.1
2.9
2.8
2.6
2.5
2.3
2.2
2.0
CFM
4316
4058
3825
3652
3442
3225
2970
2742
2294
-
1 Turn
5
RPM W
BHP
1246 2800 3.0
1248 2708 2.9
1252 2534 2.7
1254 2426 2.6
1256 2306 2.5
1259 2173 2.3
1262 2049 2.2
1266 1944 2.1
1268 1687 1.8
-
CFM
4139
3882
3664
3436
3153
2898
2617
2251
-
TURNS OPEN4
2 Turns
5
RPM W BHP CFM
1195 2476 2.7 3886
1199 2391 2.6 3612
1201 2290 2.5 3369
1204 2097 2.3 3118
1207 2000 2.1 2840
1209 1858 2.0 2560
1212 1719 1.8 2216
1214 1555 1.7
-
3 Turns
5
RPM W
1146 2178
1147 2048
1149 1915
1151 1816
1153 1644
1155 1554
1158 1417
-
BHP
2.3
2.2
2.1
1.9
1.8
1.7
1.5
-
CFM
3622
3351
3100
2827
2539
2215
1758
-
4 Turns
5
RPM W
1092 1894
1095 1775
1097 1643
1099 1552
1100 1398
1103 1294
1105 1116
-
BHP
2.0
1.9
1.8
1.7
1.5
1.4
1.2
-
5 Turns
5
CFM RPM W BHP
3413 1037 1644 1.8
3139 1039 1550 1.7
2869 1041 1408 1.5
2583 1042 1307 1.4
2259 1045 1173 1.3
1828 1047 1027 1.1
-
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
7-1/2 TON OPTIONAL MOTOR SIDE SHOT BLOWER PERFORMANCE
2.5
External Static ("WC)
2
1.5
1
0.5
0
1500
5 Turns
2000
2500
3000
4 Turns
3500
3 Turns 2 Turns 1 Turn
4000
0 Turns
4500
5000
CFM
50
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 53: DL, DU-08 (8-1/2 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE
ESP3
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
CFM
4467
4216
4001
3804
3603
3370
3185
2928
2678
2326
0 Turns
5
RPM W
1295 3131
1299 3018
1301 2861
1304 2729
1308 2598
1310 2435
1312 2327
1315 2173
1319 2055
1354 1844
BHP
3.4
3.2
3.1
2.9
2.8
2.6
2.5
2.3
2.2
2.0
CFM
4316
4058
3825
3652
3442
3225
2970
2742
2294
-
1 Turn
5
RPM W
BHP
1246 2800 3.0
1248 2708 2.9
1252 2534 2.7
1254 2426 2.6
1256 2306 2.5
1259 2173 2.3
1262 2049 2.2
1266 1944 2.1
1268 1687 1.8
-
CFM
4139
3882
3664
3436
3153
2898
2617
2251
-
TURNS OPEN4
2 Turns
5
RPM W BHP CFM
1195 2476 2.7 3886
1199 2391 2.6 3612
1201 2290 2.5 3369
1204 2097 2.3 3118
1207 2000 2.1 2840
1209 1858 2.0 2560
1212 1719 1.8 2216
1214 1555 1.7
-
3 Turns
5
RPM W
1146 2178
1147 2048
1149 1915
1151 1816
1153 1644
1155 1554
1158 1417
-
BHP
2.3
2.2
2.1
1.9
1.8
1.7
1.5
-
CFM
3622
3351
3100
2827
2539
2215
1758
-
4 Turns
5
RPM W
1092 1894
1095 1775
1097 1643
1099 1552
1100 1398
1103 1294
1105 1116
-
BHP
2.0
1.9
1.8
1.7
1.5
1.4
1.2
-
5 Turns
5
CFM RPM W BHP
3413 1037 1644 1.8
3139 1039 1550 1.7
2869 1041 1408 1.5
2583 1042 1307 1.4
2259 1045 1173 1.3
1828 1047 1027 1.1
-
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
8-1/2 TON STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE
2.5
External Static ("WC)
2
1.5
1
0.5
0
1500
5 Turns
2000
2500
3000
4 Turns
3500
3 Turns 2 Turns 1 Turn
4000
0 Turns
4500
5000
CFM
Johnson Controls Unitary Products
51
264975-BIM-B-1208
TABLE 54: DL, DU-08 (8-1/2 TON) OPTIONAL DRIVE SIDE SHOT BLOWER PERFORMANCE
ESP3
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
CFM
–
–
–
4085
3900
3708
3500
3273
3050
0 Turns
RPM W 5
–
–
–
–
–
–
1354 3160
1362 3050
1366 2910
1369 2750
1372 2600
1376 2450
BHP
–
–
–
3.4
3.3
3.1
3.0
2.8
2.6
CFM
4478
4243
4037
3848
3678
3456
3238
3012
2848
1 Turn
RPM W 5
1289 3150
1293 3020
1294 2920
1295 2770
1309 2650
1313 2490
1315 2370
1317 2230
1320 2140
BHP
3.4
3.2
3.1
3.0
2.8
2.7
2.5
2.4
2.3
CFM
4375
4116
3900
3691
3469
3239
2994
2752
2373
TURNS OPEN4
2 Turns
RPM W 5 BHP CFM
1265 2890 3.1 4092
1266 2740 2.9 3831
1266 2600 2.8 3615
1267 2500 2.7 3393
1267 2340 2.5 3161
1268 2200 2.4 2910
1269 2070 2.2 2633
1269 1910 2.0 2282
1273 1730 1.9
–
3 Turns
RPM W 5
1203 2460
1204 2330
1205 2200
1206 2090
1206 1960
1207 1840
1208 1700
1210 1540
–
–
BHP
2.6
2.5
2.4
2.2
2.1
2.0
1.8
1.7
–
4 Turns
RPM W 5
1142 2250
1144 2100
1147 1960
1149 1828
1150 1700
1151 1500
1151 1400
1152 1200
–
–
CFM
3967
3691
3460
3195
2931
2655
2313
1833
–
BHP
2.4
2.2
2.1
1.9
1.8
1.7
1.5
1.3
–
CFM
3677
3402
3199
2900
2609
2302
1801
–
–
5 Turns
RPM W 5
1086 1880
1088 1790
1091 1670
1093 1540
1094 1410
1096 1300
1099 1100
–
–
–
–
BHP
2.0
1.9
1.8
1.6
1.5
1.4
1.2
–
–
1. Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2. Blower performance includes two-inch throwaway filters.
3. ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4. “Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5. W = Watts
8-1/2 TON OPTIONAL DRIVE SIDE SHOT BLOWER PERFORMANCE
2
1.8
External Static ("WC)
1.6
1.4
1.2
1
0.8
0 Turns
0.6
0.4
0.2
5 Turns
0
1500
2000
2500
3000
3500
4 Turns 3 Turns 2 Turns 1 Turn
4000
4500
5000
CFM
52
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 55: DL, DU-10 (10 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
1
2
3
4
5
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
0.2
-
-
-
-
-
-
-
-
-
4368
1843
1.98
4132
1624
1.74
3870
1423
1.53
0.4
-
-
-
4515
2192
2.35
4213
1885
2.02
4020
1692
1.81
3791
1491
1.60
3499
1283
1.38
0.6
-
-
-
4192
2027
2.17
3905
1741
1.87
3657
1537
1.65
3383
1345
1.44
3062
1149
1.23
0.8
-
-
-
3838
1858
1.99
3534
1591
1.71
3236
1386
1.49
2934
1202
1.29
-
-
-
1.0
3755
1942
2.08
3489
1695
1.82
3081
1425
1.53
-
-
-
-
-
-
-
-
-
1.2
3337
1757
1.88
2918
1475
1.58
-
-
-
-
-
-
-
-
-
-
-
-
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
TABLE 56: DL, DU-10 (10 TON) OPTIONAL MOTOR SIDE SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
1
2
3
4
5
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
0.2
-
-
-
-
-
-
-
-
-
-
-
-
5067
2614
2.80
4809
2290
2.46
0.4
-
-
-
-
-
-
5179
3112
3.34
4884
2703
2.90
4729
2401
2.57
4459
2113
2.27
0.6
-
-
-
-
-
-
4925
2943
3.16
4585
2521
2.70
4429
2244
2.41
4137
1964
2.11
0.8
-
-
-
4974
3220
3.45
4607
2727
2.92
4267
2342
2.51
4099
2080
2.23
3783
1809
1.94
1.0
4975
3453
3.70
4657
2995
3.21
4305
2550
2.73
3941
2171
2.33
3751
1919
2.06
3371
1630
1.75
1.2
4679
3423
3.67
4366
2808
3.01
4022
2373
2.54
3545
1978
2.12
3305
1741
1.87
-
-
-
1.4
4429
3065
3.29
4040
2607
2.80
3669
2673
2.87
2918
1700
1.82
-
-
-
-
-
-
1.6
4107
2845
3.05
3620
2357
2.53
2931
1830
1.96
-
-
-
-
-
-
-
-
-
1.8
3553
2500
2.68
2756
1899
2.04
-
-
-
-
-
-
-
-
-
-
-
-
2.0
2439
1939
2.08
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
Johnson Controls Unitary Products
53
264975-BIM-B-1208
TABLE 57: DL, DU-12 (12-1/2 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
1
2
3
4
5
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
0.4
-
-
-
-
-
-
5201
3162
3.39
4966
2796
3.00
4681
2405
2.58
4355
2054
2.20
0.6
-
-
-
5220
3395
3.64
4942
2980
3.20
4657
2608
2.80
4358
2230
2.39
4007
1890
2.03
3194
3.43
4661
2806
3.01
4378
2572
2.76
4016
2057
2.21
0.8
-
-
-
4944
-
-
-
1.0
5003
3490
3.74
4647
2988
3.20
4380
2636
2.83
4030
2257
2.42
-
-
-
-
-
-
1.2
4724
3290
3.53
4363
2875
3.08
4012
2505
2.69
-
-
-
-
-
-
-
-
-
1.4
4428
3040
3.26
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
TABLE 58: DL, DU-12 (12-1/2 TON) OPTIONAL MOTOR SIDE SHOT BLOWER PERFORMANCE1 2
TURNS OPEN4
ESP3
0
1
2
3
4
5
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
CFM
W5
BHP
0.4
-
-
-
6447
5315
5.70
6207
4760
5.1046
5966
4205
4.51
5717
3716
3.98
5470
3307
3.55
0.6
-
-
-
6110
4917
5.27
5965
4464
4.79
5740
4023
4.31
5430
3501
3.75
5126
3054
3.28
0.8
-
-
-
5772
4519
4.85
5741
4274
4.58
5503
3821
4.10
5162
3294
3.53
4849
2870
3.08
1.0
6235
5521
5.92
5628
4407
4.73
5474
4048
4.34
5244
3611
3.87
4882
3101
3.33
4530
2667
2.86
1.2
5881
5137
5.51
5384
4205
4.51
5248
3854
4.13
4941
3387
3.63
4589
2906
3.12
4225
2502
2.68
1.4
5695
4950
5.31
5123
3996
4.29
5014
3670
3.94
4651
3178
3.41
4284
2716
2.91
3858
2280
2.45
1.6
5471
4728
5.07
4919
3828
4.11
4732
3460
3.71
4365
2983
3.20
3951
2516
2.70
3491
2058
2.21
1.8
5242
4514
4.84
4656
3611
3.87
4438
3240
3.47
3998
2740
2.94
3618
2316
2.48
-
-
-
2.0
4954
4231
4.54
4339
3380
3.62
3905
2861
3.07
3631
2497
2.68
-
-
-
-
-
-
2.2
4585
3934
4.22
4022
3149
3.38
-
-
-
-
-
-
-
-
-
-
-
-
2.4
4217
3637
3.90
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2.6
3848
3340
3.58
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
54
1.
Blower performance for gas heat includes maximum number of heat tubes available for each tonnage.
2.
Blower performance includes two-inch throwaway filters.
3.
ESP (External Static Pressure) given is that available for the supply and return air duct system. All internal resistances have been
deducted from the total static pressure of the blower.
4.
“Turns Open” refers to the setting of the variable pitch motor sheave, where “0 Turns Open” is fully closed.
5.
W = Watts
Johnson Controls Unitary Products
264975-BIM-B-1208
NOTES FOR TABLE 35 THROUGH TABLE 58:
•
•
Blower performance includes dry coil and two-inch
filters.
Blower performance for gas heat includes the maximum
number of heat tubes available for each tonnage.
•
ESP (External Static Pressure) given is that available for
the supply and return air duct system. All internal resistances have been deducted from the total static pressure
of the blower.
TABLE 59: INDOOR BLOWER SPECIFICATIONS
MOTOR
MOTOR SHEAVE
BLOWER SHEAVE
MODEL
BELT
HP
RPM
Eff.
SF
Frame
Datum Dia. (in.)
Bore (in.)
Model
Datum Dia. (in.)
Bore (in.)
Model
1-1/2
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
9.5
1
AK99
A58
2
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
7.5
1
AK79
A55
1-1/2
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
7.0
1
AK74
A49
2
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
6.2
1
AK66
A49
2
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
6.5
1
AK69
A49
3
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
6.0
1
AK64
A49
2
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
6.5
1
AK69
A49
3
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
6.0
1
AK64
A49
3
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
6.0
1
AK64
A49
3
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
5.7
1
AK61
A49
3
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
6.0
1
AK64
A49
3
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
5.7
1
AK61
A49
2
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
8.5
1
AK89
A56
3
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
7.0
1
AK74
A54
2
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
8.5
1
AK89
A56
3
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
7.0
1
AK74
A54
3
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
7.0
1
AK74
A54
5
1725
87%
1.15
184T
4.3 - 5.3
1 1/8
1VP56
6.7
1
BK77
BX55
3
1725
80%
1.15
56
3.4 - 4.4
7/8
1VM50
7.0
1
AK74
A54
5
1725
87%
1.15
184T
4.3 - 5.3
1 1/8
1VP56
6.7
1
BK77
BX55
DL-06
DU-06
DL-07
DU-07
DL-08
DU-08
DL-10
DU-10
DL-12
DU-12
TABLE 60: POWER EXHAUST SPECIFICATIONS
POWER EXHAUST
MODEL
VOLT
PHASE
2PE0473225
2PE0473246
2PE0473258
208/230
460
575
1
1
1
1.
MOTOR
HP
0.75
RPM1
1075
1050
ELECTRICAL
QTY
1
LRA
FLA
MCA
FUSE
SIZE
CFM@
0.1 ESP
24.9
5.0
2.2
1.5
6.3
2.8
1.9
10
5
4
3,800
-
Motors are multi-tapped and factory wired for high speed.
Johnson Controls Unitary Products
55
264975-BIM-B-1208
AIR BALANCE
Start the supply air blower motor. Adjust the resistances in both the supply and the return air duct systems to balance the air distribution throughout the conditioned space. The job specifications may require that this balancing be done by someone other
than the equipment installer.
Belt drive blower systems MUST be adjusted to the
specific static and CFM requirements for the application. The Belt drive blowers are NOT set at the
factory for any specific static or CFM. Adjustments of
the blower speed and belt tension are REQUIRED.
Tighten blower pulley and motor sheave set screws
after these adjustments. Re-checking set screws
after 10-12 hrs. run time is recommended.
56
Johnson Controls Unitary Products
264975-BIM-B-1208
CHECKING AIR QUANTITY
METHOD ONE
1.
Remove the dot plugs from the duct panel (for location of
the dot plugs see Figure 10).
2.
Insert eight-inches of 1/4 inch metal tubing into the airflow on both sides of the indoor coil.
NOTE: The tubes must be inserted and held in a position
perpendicular to the air flow so that velocity pressure will not affect the static pressure readings.
3.
Use an Inclined Manometer or Magnehelic to determine
the pressure drop across a dry evaporator coil. Since the
moisture on an evaporator coil can vary greatly, measuring the pressure drop across a wet coil under field conditions could be inaccurate. To assure a dry coil, the
compressors should be de-activated while the test is
being run.
METHOD TWO
1.
Drill two 5/16 inch holes, one in the return air duct as
close to the inlet of the unit as possible, and another in
the supply air duct as close to the outlet of the unit as
possible.
2.
Using the whole drilled in step 1, insert eight inches of
1/4 inch metal tubing into the airflow of the return and
supply air ducts of the unit.
NOTE: The tubes must be inserted and held in position perpendicular to the airflow so that velocity pressure
will not affect the static pressure readings.
3.
Use an Inclined Manometer or Magnehelic to determine
the pressure drop across the unit. This is the External
Static Pressure (ESP). In order to obtain an accurate
measurement, be certain that the air filters are clean.
4.
Determine the number of turns the variable motor
sheave is open.
5.
Select the correct blower performance table for the unit
from Tables 35 - 46. Tables are presented for horizontal
and downflow configuration.
6.
To adjust Measured CFM to Required CFM, see ’SUPPLY AIR DRIVE ADJUSTMENT’.
Determine the unit Measured CFM from the Blower Performance Table, External Static Pressure and the number of turns the variable motor sheave is open.
7.
To adjust Measured CFM to Required CFM, see ’SUPPLY AIR DRIVE ADJUSTMENT’.
6.
After readings have been obtained, remove the tubes
and replace the dot plugs.
8.
After reading has been obtained, remove the tubes and
seal holes.
7.
Tighten blower pulley and motor sheave set screws after
any adjustments. Re-check set screws after 10-12 hrs.
run time is recommended.
9.
Tighten blower pulley and motor sheave set screws after
any adjustments. Re-check set screws after 10-12 hrs.
run time is recommended.
NOTE: De-energize the compressors before taking any test
measurements to assure a dry evaporator coil.
4.
5.
The CFM through the unit can be determined from the
pressure drop indicated by the manometer by referring to
Figure 26. In order to obtain an accurate measurement,
be certain that the air filters are clean.
NOTE: With the addition of field installed accessories
repeat this procedure.
Failure to properly adjust the total system air quantity can result in extensive blower damage.
Failure to properly adjust the total system air quantity can result in extensive blower damage.
Johnson Controls Unitary Products
57
264975-BIM-B-1208
DL/DU 50" Cabinet
Indoor Coil Pressure Drop vs. Airflow
0.9
0.8
Dry Coil Delta P (IWG)
0.7
DL, DU-12
0.6
0.5
0.4
DL, DU-10
0.3
DL-06
0.2
0.1
0
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
Airflow (CFM)
FIGURE 26 - DRY COIL DELTA P 50" CABINET
DL, DU 42" CABINET INDOOR COIL PRESSURE DROP VS AIRFLOW
0.55
DL-07, -08
DU-06, -07, -08
0.5
Dry Coil Delta P (IWG)
0.45
0.4
0.35
0.3
0.25
0.2
2000
2500
3000
3500
4000
4500
Airflow (CFM)
FIGURE 27 - DRY COIL DELTA P 42" CABINET
58
Johnson Controls Unitary Products
264975-BIM-B-1208
SUPPLY AIR DRIVE ADJUSTMENT
CFM • 4.0 in. = 4.21 in.
( 4,000
3,800 CFM )
Before making any blower speed changes review
the installation for any installation errors, leaks or
undesirable systems effects that can result in loss of
airflow.
Even small changes in blower speed can result in
substantial changes in static pressure and BHP.
BHP and AMP draw of the blower motor will
increase by the cube of the blower speed. Static
pressure will increase by the square of the blower
speed. Only qualified personnel should make blower
speed changes, strictly adhering to the fan laws.
At unit start-up, the measured CFM may be higher or lower
than the required CFM. To achieve the required CFM, the
speed of the drive may have adjusted by changing the datum
diameter (DD) of the variable pitch motor sheave as
described below:
(
Required CFM
Measured CFM
Use Table 63 to locate the DD nearest to 4.21 in. Close the
sheave to 1 turn open.
New BHP
= (Speed increase)3 • BHP at 3,800 CFM
= (Speed increase)3 • Original BHP
= New BHP
New motor Amps
= (Speed increase)3 • Amps at 3,800 CFM
= (Speed increase)3 • Original Amps
= New Amps
) • Existing DD = New DD
Use the following tables and the DD calculated per the above
equation to adjust the motor variable pitch sheave.
EXAMPLE
A 12.5 ton unit was selected to deliver 4,000 CFM with a 3
HP motor, but the unit is delivering 3,800 CFM. The variable
pitch motor sheave is set at 2 turns open.
Use the equation to determine the required DD for the new
motor sheave,
Johnson Controls Unitary Products
Belt drive blower systems MUST be adjusted to the
specific static and CFM requirements for the application. The Belt drive blowers are NOT set at the
factory for any specific static or CFM. Adjustments of
the blower speed and belt tension are REQUIRED.
Tighten blower pulley and motor sheave set screws
after these adjustments. Re-checking set screws
after 10-12 hrs. run time is recommended.
59
264975-BIM-B-1208
TABLE 61: ADDITIONAL STATIC RESISTANCE DL-06, -10, -12 AND DU-10, -12
CFM
1900
2100
2300
2500
2700
2900
3100
3300
3500
3700
3900
4100
4300
4500
4700
4900
5100
5300
5500
5700
5900
6100
6300
Cooling Only1
Economizer2 3
0.06
0.07
0.08
0.09
0.11
0.12
0.14
0.16
0.18
0.20
0.23
0.25
0.28
0.30
0.33
0.36
0.39
0.42
0.45
0.48
0.52
0.56
0.60
0.02
0.02
0.02
0.02
0.03
0.03
0.03
0.03
0.04
0.04
0.04
0.04
0.05
0.05
0.05
0.05
0.06
0.06
0.06
0.06
0.07
0.07
0.07
Electric Heat KW2
9
18
24
36
54
0.05
0.06
0.07
0.08
0.09
0.10
0.12
0.13
0.15
0.17
0.19
0.21
0.23
0.25
0.28
0.30
0.33
0.35
0.38
0.41
0.44
0.47
0.50
0.06
0.07
0.08
0.09
0.10
0.11
0.13
0.14
0.16
0.18
0.20
0.22
0.24
0.26
0.29
0.31
0.34
0.37
0.40
0.43
0.46
0.49
0.53
0.07
0.08
0.09
0.10
0.12
0.13
0.15
0.17
0.19
0.21
0.23
0.25
0.28
0.30
0.33
0.35
0.38
0.41
0.44
0.47
0.50
0.53
0.56
0.08
0.09
0.10
0.11
0.13
0.14
0.16
0.18
0.20
0.22
0.24
0.26
0.29
0.31
0.34
0.37
0.40
0.43
0.46
0.49
0.53
0.56
0.59
0.10
0.11
0.13
0.14
0.16
0.18
0.20
0.22
0.24
0.26
0.28
0.31
0.34
0.37
0.40
0.43
0.46
0.49
0.53
0.56
0.59
0.62
0.65
1.
Add these resistance values to the available static resistance in the respective Blower Performance Tables.
2.
Deduct these resistance values from the available external static pressure shown in the respective Blower Performance Table.
3.
The pressure drop through the economizer is greater for 100% outdoor air than for 100% return air. If the resistance of the return
air duct system is less than 0.25 IWG, the unit will deliver less CFM during full economizer operation.
TABLE 62: ADDITIONAL STATIC RESISTANCE DL-07, -08 AND DU-06, -07, -08
CFM
1900
2100
2300
2500
2700
2900
3100
3300
3500
3700
3900
4100
4300
60
Cooling Only1
Economizer2 3
-0.004
0.01
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.08
0.09
0.09
0.10
0.07
0.09
0.11
0.13
0.16
0.18
0.20
0.22
0.24
0.27
0.29
0.31
0.33
Electric Heat KW2
9
18
24
36
54
0.05
0.06
0.07
0.08
0.09
0.1
0.12
0.13
0.15
0.17
0.19
0.21
0.23
0.06
0.07
0.08
0.09
0.1
0.11
0.13
0.14
0.16
0.18
0.2
0.22
0.24
0.07
0.08
0.09
0.1
0.12
0.13
0.15
0.17
0.19
0.21
0.23
0.25
0.28
0.08
0.09
0.1
0.11
0.13
0.14
0.16
0.18
0.2
0.22
0.24
0.26
0.29
0.1
0.11
0.13
0.14
0.16
0.18
0.2
0.22
0.24
0.26
0.28
0.31
0.34
1.
Deduct these resistance values to the available static resistance in the respective Blower Performance Tables.
2.
Deduct these resistance values from the available external static pressure shown in the respective Blower Performance Table.
3.
The pressure drop through the economizer is greater for 100% outdoor air than for 100% return air. If the resistance of the return
air duct system is less than 0.25 IWG, the unit will deliver less CFM during full economizer operation.
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 63: MOTOR SHEAVE DATUM DIAMETERS
1VM50x7/8
(1-1/2, 2 & 3 HP Motor)
1VP56x1-1/8
(5 HP Motor)
Turns Open
Datum
Diameter
Turns Open
Datum
Diameter
0
4.4
1
5.3
1/2
4.3
1-1/2
5.2
1
4.2
2
5.1
1-1/2
4.1
2-1/2
5.0
2
4.0
3
4.9
2-1/2
3.9
3-1/2
4.8
3
3.8
4
4.7
3-1/2
3.7
4-1/2
4.6
4
3.6
5
4.5
4-1/2
3.5
5-1/2
4.4
5
3.4
6
4.3
OPERATION
SEQUENCE OF OPERATIONS OVERVIEW
For the DL/DU series of units, the thermostat makes a circuit
between "R" and "Y1" for the first stage of cooling.
The call is passed to the Unit Control Board (UCB), which
then determines whether the requested operation is available
and, if so, which components to energize.
For gas heating, the UCB monitors the "W1" call but does not
handle the operation of the gas furnace. An ignition control
board controls the gas heater operation. For electric heat
units, the UCB passes the call to the electric heater. In both
cases, when the "W1" call is sensed, the indoor air blower is
energized following a specified heating delay.
If at any time a call for both heating and cooling are present,
the heating operation will be performed. If operating, the cooling system is halted as with a completion of a call for cooling.
Heating always takes priority.
COOLING SEQUENCE OF OPERATION
CONTINUOUS BLOWER
By setting the room thermostat fan switch to "ON," the supply
air blower will operate continuously.
INTERMITTENT BLOWER
With the room thermostat fan switch set to "AUTO" and the
system switch set to either the "AUTO" or "HEAT" settings,
the blower is energized whenever a cooling or heating operation is requested. The blower is energized after any specified
delay associated with the operation.
When energized, the indoor blower has a minimum run time
of 30 seconds. Additionally, the indoor blower has a delay of
10 seconds between operations.
Johnson Controls Unitary Products
NO OUTDOOR AIR OPTIONS
When the thermostat calls for the first stage of cooling, the
low-voltage control circuit from “R” to “Y1” and “G” is completed. The UCB energizes the economizer (if installed and
free cooling is available) or the first available compressor*
and the condenser fans. For first stage cooling, compressor
#1 is energized. If compressor #1 is unavailable, compressor
#2 is energized. After completing the specified fan on delay
for cooling, the UCB will energize the blower motor.
When the thermostat calls for the second stage of cooling,
the low-voltage control circuit from “R” to “Y2” is completed.
The control board energizes the first available compressor. If
free cooling is being used for the first stage of cooling, compressor #1 is energized. If compressor #1 is active for first
stage cooling or the first compressor is locked-out, compressor #2 is energized. In free-cooling mode, if the call for the
second stage of cooling continues for 20 minutes, compressor #2 is energized, provided it has not been locked-out.
If there is an initial call for both stages of cooling, the UCB will
delay energizing compressor #2 by 30 seconds in order to
avoid a power rush.
Once the thermostat has been satisfied, it will de-energize Y1
and Y2. If the compressors have satisfied their minimum run
times, the compressors and condenser fans are de-energized. Otherwise, the unit operates each cooling system until
the minimum run times for the compressors have been completed. Upon the final compressor de-energizing, the blower
is stopped following the elapse of the fan off delay for cooling.
* To be available, a compressor must not be locked-out due
to a high or low-pressure switch or freezestat trip and the
Anti-Short Cycle Delay (ASCD) must have elapsed.
ECONOMIZER WITH SINGLE ENTHALPY SENSOR When the room thermostat calls for "first-stage" cooling, the
low voltage control circuit from "R" to "G" and "Y1" is completed. The UCB energizes the blower motor (if the fan switch
on the room thermostat is set in the "AUTO" position) and
drives the economizer dampers from fully closed to their minimum position. If the enthalpy of the outdoor air is below the
set point of the enthalpy controller (previously determined),
"Y1" energizes the economizer. The dampers will modulate to
maintain a constant supply air temperature as monitored by
the discharge air sensor. If the outdoor air enthalpy is above
the set point, "Y1" energizes compressor #1.
When the thermostat calls for "second-stage" cooling, the low
voltage control circuit from "R" to "Y2" is completed. The UCB
energizes the first available compressor. If the enthalpy of the
outdoor air is below the set point of the enthalpy controller
(i.e. first stage has energized the economizer), "Y2" will energize compressor #1. If the outdoor air is above the set point,
"Y2" will energize compressor #2.
Once the thermostat has been satisfied, it will de-energize
“Y1” and “Y2”. If the compressors have satisfied their minimum run times, the compressors and condenser fans are deenergized. Otherwise, the unit operates each cooling system
until the minimum run times for the compressors have been
61
264975-BIM-B-1208
completed. Upon the final compressor de-energizing, the
blower is stopped following the elapse of the fan off delay for
cooling, and the economizer damper goes to the closed position. If the unit is in continues fan operation, the economizer
damper goes to the minimum position.
ECONOMIZER WITH DUAL ENTHALPY SENSORS The operation with the dual enthalpy sensors is identical to
the single sensor except that a second enthalpy sensor is
mounted in the return air. This return air sensor allows the
economizer to choose between outdoor air and return air,
whichever has the lowest enthalpy value, to provide maximum operating efficiency.
ECONOMIZER WITH POWER EXHAUST A unit equipped with an economizer (single or dual enthalpy)
and a power exhaust operates as specified above with one
addition. The power exhaust motor is energized 45 seconds
after the actuator position exceeds the exhaust fan set point
on the economizer control. When the power exhaust is operating, the second stage of mechanical cooling will not operate. As always, the "R" to "G" connection provides minimum
position but does not provide power exhaust operation.
MOTORIZED OUTDOOR AIR DAMPERS This system operation is the same as the units with no outdoor air options with one exception. When the "R" to "G" circuit is complete, the motorized damper drives open to a
position set by the thumbwheel on the damper motor. When
the "R" to "G" circuit is opened, the damper spring returns
fully closed.
COOLING OPERATION ERRORS
Each cooling system is monitored for operation outside of the
intended parameters. Errors are handled as described below.
All system errors override minimum run times for compressors.
HIGH-PRESSURE LIMIT SWITCH
During cooling operation, if a high-pressure limit switch
opens, the UCB will de-energize the associated compressor,
initiate the ASCD (Anti-short cycle delay), and, if the other
compressor is idle, stop the condenser fans. If the call for
cooling is still present at the conclusion of the ASCD, the
UCB will re-energize the halted compressor.
Should a high-pressure switch open three times within two
hours of operation, the UCB will lock-out the associated compressor and flash a code (see Table 80). If the other compressor is inactive, the condenser fans will be de-energized.
LOW-PRESSURE LIMIT SWITCH
The low-pressure limit switch is not monitored during the initial 30 seconds of a cooling system's operation. For the following 30 seconds, the UCB will monitor the low-pressure
switch to ensure it closes. If the low-pressure switch fails to
close after the 30-second monitoring phase, the UCB will deenergize the associated compressor, initiate the ASCD, and,
if the other compressor is idle, stop the condenser fans.
62
Once the low-pressure switch has been proven (closed during the 30-second monitor period described above), the UCB
will monitor the low-pressure limit switch for any openings. If
the low-pressure switch opens for greater than 5 seconds,
the UCB will de-energize the associated compressor, initiate
the ASCD, and, if the other compressor is idle, stop the condenser fans.
If the call for cooling is still present at the conclusion of the
ASCD, the UCB will re-energize the halted compressor.
Should a low-pressure switch open three times within one
hour of operation, the UCB will lock-out the associated compressor and flash a code (Table 80). If the other compressor
is inactive, the condenser fans will be de-energized.
FREEZESTAT
During cooling operation, if a freezestat opens, the UCB will
de-energize the associated compressor, initiate the ASCD,
and, if the other compressor is idle, stop the condenser fans.
If the call for cooling is still present at the conclusion of the
ASCD, the UCB will re-energize the halted compressor.
Should a freezestat open three times within two hours of
operation, the UCB will lock-out the associated compressor
and flash a code (Table 80). If the other compressor is inactive, the condenser fans will be de-energized.
LOW AMBIENT COOLING
To determine when to operate in low ambient mode, the UCB
has a pair of terminals connected to a temperature-activated
switch set at 45ºF. When the low ambient switch is closed
and the thermostat is calling for cooling, the UCB will operate
in the low ambient mode.
Low ambient mode operates the compressors in this manner:
10 minutes on, 5 minutes off. The indoor blower is operated
throughout the cycle. The 5-minute off period is necessary to
defrost the indoor coil.
Low ambient mode always begins with compressor operation. Compressor minimum run time may extend the minutes
of compressor operation. The defrost cycle will begin immediately following the elapse of the minimum run time.
When operating in low ambient mode, the UCB will not lockout the compressors due to a freezestat trip. However, a
freezestat trip will de-energize the associated compressor. If
the call for cooling is still present at the end of the ASCD and
the freezestat has closed, the unit will resume operation.
SAFETY CONTROLS
The unit control board monitors the following inputs for each
cooling system:
1.
A suction line freezestat to protect against low evaporator temperatures due to a low airflow or a low return air
temperature, (opens at 26 ± 5 °F and resets at 38 ± 5°F).
2.
A high-pressure switch to protect against excessive discharge pressures due to a blocked condenser coil or a
Johnson Controls Unitary Products
264975-BIM-B-1208
condenser motor failure, (opens at 405 ± 10 psig or 440
± 10 psig depending on unit model).
3.
A low-pressure switch to protect against loss of refrigerant charge, (opens at 22 ± 5 psig or 45 ± 5 psig).
The above pressure switches are hard-soldered to the unit.
The refrigeration systems are independently monitored and
controlled. On any fault, only the associated system will be
affected by any safety/preventive action. The other refrigerant
system will continue in operation unless it is affected by the
fault as well.
The unit control board monitors the temperature limit switch
of electric heat units and the temperature limit switch and the
gas valve of gas furnace units.
COMPRESSOR PROTECTION
In addition to the external pressure switches, the compressors
also have inherent (internal) protection. If there is an abnormal
temperature rise in a compressor, the protector will open to
shut down the compressor. The UCB incorporates features to
minimize compressor wear and damage. An Anti-Short Cycle
Delay (ASCD) is utilized to prevent operation of a compressor
too soon after its previous run. Additionally, a minimum run
time is imposed any time a compressor is energized.
The ASCD is initiated on unit start-up and on any compressor
reset or lock-out.
FLASH CODES
The UCB will initiate a flash code associated with errors
within the system. Refer to UNIT CONTROL BOARD FLASH
CODES Table 80.
RESET
Remove the call for cooling, by raising thermostat setting
higher than the conditioned space temperature. This resets
any pressure or freezestat flash codes.
ELECTRIC HEATING SEQUENCE OF OPERATIONS
The following sequence describes the operation of the electric heat section.
Two-stage heating:
a.
b.
Upon a call for first stage heat by the thermostat, the
heater relay (RA) will be energized. After completing
the specified fan on delay for heating, the UCB will
energize the blower motor. If the second stage of
heat is required, heater relay (RB) will be energized.
After completing the specified fan on delay for heating, the UCB will energize the blower motor.
The thermostat will cycle the electric heat to satisfy
the heating requirements of the conditioned space.
Johnson Controls Unitary Products
ELECTRIC HEAT OPERATION ERRORS
TEMPERATURE LIMIT
If the UCB senses zero volts from the high temperature limit,
the indoor blower motor is immediately energized.
This limit is monitored regardless of unit operation status, i.e.
the limit is monitored at all times.
If the temperature limit opens three times within one hour, it
will lock-on the indoor blower motor and a flash code is initiated (See Table 80).
SAFETY CONTROLS
The UCB monitors the temperature limit switch of electric
heat units.
The control circuit includes the following safety controls:
LIMIT SWITCH (LS)
This control is located inside the heater compartment and is
set to open at the temperature indicated in the Electric Heat
Limit Setting Table 64. It resets automatically. The limit switch
operates when a high temperature condition, caused by inadequate supply air flow occurs, thus shutting down the heater
and energizing the blower.
TABLE 64: ELECTRIC HEAT LIMIT SETTING
50” CABINET
UNIT (TONS)
DL-06 (6.5)
DL-06, -10, -12 (6.5, 10, 12.5)
DU-10, -12 (10, 12.5)
DL-06, -10, -12 (6.5, 10, 12.5)
DU-10, -12 (10, 12.5)
DL-06, -10, -12 (6.5, 10, 12.5)
DU-10, -12 (10, 12.5)
DL, DU-10, -12 (10, 12.5)
DL-06 (6.5)
DL-06, -10, -12 (6.5, 10, 12.5)
DU-10, -12 (10, 12.5)
DL-06, -10, -12 (6.5, 10, 12.5)
DU-10, -12 (10, 12.5)
DL-06, -10, -12 (6.5, 10, 12.5)
DU-10, -12 (10, 12.5)
DL, DU-10, -12 (10, 12.5)
DL-06 (6,5)
DL-06, -10, -12 (6.5, 10, 12.5)
DU-10, -12 (10, 12.5)
DL-06, -10, -12 (6.5, 10, 12.5)
DU-10, -12 (10, 12.5)
DL-06, -10, -12 (6.5, 10, 12.5)
DU-10, -12 (10, 12.5)
DL, DU-10, -12 (10, 12.5)
VOLTAGE
208/230
480
600
HEATER
kW
LIMIT
SWITCH
OPENS °F
9
150
18
150
24
150
34
150
54
9
130
150
18
150
24
150
34
150
54
9
130
150
18
150
24
150
34
150
54
130
63
264975-BIM-B-1208
TABLE 65: ELECTRIC HEAT LIMIT SETTING 42”
CABINET
UNIT (TONS)
VOLTAGE
DL-07, -08 (7.5, 8.5)
DU-06, -07, -08 (6.5, 7.5, 8.5)
208/230
DL-07, -08(7.5, 8.5)
DU-06, -07, -08 (6.5, 7.5, 8.5)
480
DL-07, -08 (7.5, 8.5)
DU-06, -07, -08 (6.5, 7.5, 8.5)
600
HEATER
kW
LIMIT
SWITCH
OPENS °F
9
18
24
34
9
18
24
34
9
18
24
34
135
150
165
190
135
150
165
185
135
150
150
185
FLASH CODES
The UCB will initiate a flash code associated with errors
within the system. Refer to UNIT CONTROL BOARD FLASH
CODES Table 80.
RESET
IGNITION CONTROL BOARD
FIRST STAGE OF HEATING
When the ICB receives a call for first stage of heating, “W1,”
the draft motor is energized. Once the draft motor has been
proven, a 30-second purge is initiated. At the end of the
purge, the GV is opened, and the spark ignitor is energized
for 10 seconds. The ICB then checks for the presence of
flame. If flame is detected, the ICB enters a flame stabilization period. If flame was not detected, the GV closes, and a
retry operation begins.
During the flame stabilization period, a loss of the flame for 2
seconds will cause the GV to close and the retry operation to
begin. After the flame stabilization period, a loss of flame for
3/4 second will cause the GV to close and the retry operation
to begin.
At the conclusion of the flame stabilization period, the ICB will
operate the gas heat in high fire for an additional 60 seconds
(for a total for 120 seconds of high fire operation). After this
60 seconds, the ICB will then use the call for the second
stage of heat to control second stage operation of the GV.
Remove the call for heating by lowering the thermostat setting lower than the conditioned space temperature.This
resets any flash codes.
When “W1” is satisfied, both valves are closed.
ELECTRIC HEAT ANTICIPATOR SETPOINTS
When the ICB receives a call for the second stage of heating,
“W2,” the ICB conducts a complete first stage ignition
sequence. If this sequence is satisfied, the second main
valve of the GV is opened.
It is important that the anticipator setpoint be correct. Too
high of a setting will result in longer heat cycles and a greater
temperature swing in the conditioned space. Reducing the
value below the correct setpoint will give shorter “ON” cycles
and may result in the lowering of the temperature within the
conditioned space. Refer to Table 66 for the required electric
heat anticipator setting.
TABLE 66: ELECTRIC HEAT ANTICIPATOR
SETPOINTS
SETTING, AMPS
W1
W2
0.13
0.1
SECOND STAGE OF HEATING
When “W2” is satisfied, the second main valve is closed.
RETRY OPERATION
When a flame is lost or is not detected during an attempt to
achieve ignition, a retry operation occurs. A 30-second purge
is performed between ignition attempts.
If the unit fails after three ignition attempts, the furnace is
locked-out for one hour. The furnace is monitored during this
one-hour period for unsafe conditions.
GAS HEATING SEQUENCE OF OPERATIONS
RECYCLE OPERATION
When the thermostat calls for the first stage of heating, the
low-voltage control circuit from “R” to “W1” is completed. A
call for heat passes through the UCB to the Ignition Control
Board (ICB). The UCB monitors the “W1” call and acts upon
any call for heat by monitoring the Gas Valve (GV). Once
voltage has been sensed at the GV, the UCB will initiate the
fan on delay for heating, energizing the indoor blower the
specified delay has elapsed.
When a flame is lost after the flame stabilization period, a
recycle operation occurs. If the unit fails after five recycle
attempts, the furnace is locked-out for one hour.
When the thermostat has been satisfied, heating calls are
ceased. The GV is immediately closed. The blower is deenergized after the fan off delay for heating has elapsed. The
draft motor performs a 30-second post purge.
64
GAS HEATING OPERATION ERRORS
LOCK-OUT
A one-hour lockout occurs following three retries or five recycles. During the one-hour lockout, flame detection, limit conditions, and main valves are tested. Any improper results will
cause the appropriate action to occur. Recycling the low voltage power cancels the lock-out.
Johnson Controls Unitary Products
264975-BIM-B-1208
TEMPERATURE LIMIT
SAFETY CONTROLS
If the UCB senses zero volts from the high temperature limit,
the indoor blower motor is immediately energized. When the
UCB again senses 24 volts from the temperature limit, the
draft motor will perform a 15-second post-purge and the
indoor blower will be de-energized following the elapse of the
fan off delay for heating.
The UCB monitors the temperature limit switch of gas heat units.
This limit is monitored regardless of unit operation status, i.e.
this limit is monitored at all times.
If the temperature limit opens three times within one hour, it
will lock-on the indoor blower motor and flash code is initiated
(See Table 80).
FLAME SENSE
Flame sensing occurs at all times. If “W1” is not present and
a flame is sensed for 2 seconds, the draft motor is energized
and the GV is kept off. The ICB halts any operation until a
flame is not detected. Once the flame detection is lost, the
ICB performs a post-purge. Normal operation is allowed concurrently with the purge (i.e. this purge can be considered the
purge associated with a call for “W1”).
If “W1” is present, a flame is sensed, but the GV is not energized, the draft motor is energized until the flame detection is
lost. Normal operation is now allowed.
The flame detection circuitry continually tests itself. If the ICB
finds the flame detection circuitry to be faulty, the ICB will not
permit an ignition sequence and the draft motor is energized.
If this failure should occur during an ignition cycle the failure
is counted as a recycle.
The control circuit includes the following safety controls:
LIMIT SWITCH (LS)
This control is located inside the gas heat compartment and
is set to open at the temperature indicated in the Gas Heat
Limit Control Settings Table 67. It resets automatically. The
limit switch operates when a high temperature condition,
caused by inadequate supply air flow occurs, thus shutting
down the heater and energizing the blower.
AUXILIARY LIMIT SWITCH (ALS)
This control is located inside the supply air compartment and
is set to open at the temperature indicated in the Gas Heat
Limit Control Settings Table 67. It resets manually. The limit
switch operates when a high temperature condition, caused
by inadequate supply air flow occurs, thus shutting down the
heater and energizing the blower.
The auxiliary limit switch is wired in series with the limit
switch. As such, the UCB cannot distinguish the auxiliary limit
and the gas heat limit switch operation except the auxiliary is
manual reset. Consequently, the control will respond in the
same manner as outlined above under “Limit Switch”.
TABLE 67: GAS HEAT LIMIT CONTROL SETTINGS1
Unit
Size
DL -06
GAS VALVE
DL -07
The UCB and ICB continuously monitor the GV.
DL -08
If the ICB senses voltage at the GV when not requested, the
ICB will energize the draft motor. The ICB will not operate the
furnace until voltage is no longer sensed at the GV. The draft
motor is stopped when voltage is not sensed at the GV.
Any time the UCB senses voltage at the GV without a call for
heat for a continuous five-minute period, the UCB will lock-on
the indoor blower and a flash code is initiated (Table 80).
When voltage is no longer sensed at the GV, the UCB will deenergize the indoor blower following the elapse of the fan off
delay for heating.
If voltage has been sensed at the GV for at least 15 seconds
during the fan on delay for heating and GV voltage or “W1” is
lost, the indoor blower is forced on for the length of the fan off
delay for heating.
DL -10
DL -12
DU -06
DU -07
DU -08
DU -10
DU -12
1.
Opt.
10
15
10
15
10
15
15
20
15
20
10
15
10
15
10
15
15
20
15
20
Main Limit Setting
°F
215
195
165
165
165
165
195
160
195
160
165
165
165
165
165
165
195
160
195
160
Rollout = 300°F, Auxiliary Limit = 200°F.
During a call for heat, if the UCB does not sense voltage at
the GV for a continuous five-minute period the UCB will initiate a flash code (Table 80). The indoor blower motor will not
be locked-on while there is no GV voltage.
Johnson Controls Unitary Products
65
264975-BIM-B-1208
The ICB monitors the Pressure and Rollout switches of gas
heat units.
The control circuit includes the following safety controls:
H E A T E X C H A N G E R T U B E
PRESSURE SWITCH (PS)
Once the draft motor has reached full speed and closes the
pressure switch during a normal ignition sequence, if the
pressure sw opens for 2 seconds, the GV will be de-energized, the ignition cycle is aborted, and the ICB flashes the
appropriate code. See Table 82 Ignition Control Flash Codes.
The draft motor is energized until the pressure switch closes
or “W1” is lost.
G A S
S U P P L Y
B U R N E R
P IP E
B U R N E R B R A C K E T
B U R N E R F L A M E
(B L U E O N L Y )
IG N IT O R
FIGURE 28 : TYPICAL FLAME
START-UP (COOLING)
ROLLOUT SWITCH (ROS)
The rollout switch is wired in series with the pressure switch.
As such, the ICB cannot distinguish the rollout switch operation from that of the pressure switch.
Consequently, the control will only respond in the same manner as outlined above under “Pressure Switch”. An open rollout will inhibit the gas valve from actuating.
PRESTART CHECK LIST
After installation has been completed:
1.
Check the electrical supply voltage being supplied. Be
sure that it is the same as listed on the unit nameplate.
2.
Set the room thermostat to the off position.
3.
Turn unit electrical power on.
4.
Set the room thermostat fan switch to on.
5.
Check indoor blower rotation.
INTERNAL MICROPROCESSOR FAILURE
If the ICB detects an internal failure, it will cease all outputs,
ignore inputs, and display the proper flash code for control
replacement. The ICB remains in this condition until replaced.
•
If blower rotation is in the wrong direction. Refer to
Phasing Section in general information section.
•
Check blower drive belt tension.
FLASH CODES
The UCB will initiate a flash code associated with errors
within the system. Refer to UNIT CONTROL BOARD FLASH
CODES Table 80.
6.
Check the unit supply air (CFM).
7.
Measure evaporator fan motor's amp draw.
RESETS
8.
Set the room thermostat fan switch to off.
Remove the call for heating by lowering the thermostat setting lower than the conditioned space temperature. This
resets any flash codes.
9.
Turn unit electrical power off.
GAS HEAT ANTICIPATOR SETPOINTS
1.
It is important that the anticipator setpoint be correct. Too
high of a setting will result in longer heat cycles and a greater
temperature swing in the conditioned space. Reducing the
value below the correct setpoint will give shorter “ON cycles
and may result in the lowering of the temperature within the
conditioned space. Refer to Table 68 for the required gas
heat anticipator setting.
NOTE: Prior to each cooling season, the crankcase heaters
must be energized at least 10 hours before the system is put into operation.
OPERATING INSTRUCTIONS
2.
Set the room thermostat setting to lower than the room
temperature.
3.
First stage compressors will energize after the built-in
time delay (five minutes).
4.
The second stage of the thermostat will energize second
stage compressor if needed.
TABLE 68: GAS HEAT ANTICIPATOR SETPOINTS
SETTING, AMPS
66
W1
W2
0.65
0.1
Turn unit electrical power on.
Johnson Controls Unitary Products
264975-BIM-B-1208
POST START CHECK LIST
1.
Verify proper system pressures for both circuits.
2.
Measure the temperature drop across the evaporator coil.
2.
Check for correct manifold gas pressures. (See ’CHECKING GAS INPUT’.)
3.
Check the supply gas pressure. It must be within the limits shown on the rating nameplate. Supply pressure
should be checked with all gas appliances in the building
at full fire. At no time should the standby gas pressure
exceed 10.5 in. or the operating pressure drop below 4.5
in for natural gas units. If gas pressure is outside these
limits, contact the local gas utility or propane supplier for
corrective action.
START-UP (GAS HEAT)
PRE-START CHECK LIST
Complete the following checks before starting the unit.
1.
Check the type of gas being supplied. Be sure that it is
the same as listed on the unit nameplate.
2.
Make sure that the vent outlet and combustion air inlet
are free of any debris or obstruction.
OPERATING INSTRUCTIONS
This furnace is equipped with an automatic re-ignition
system. DO NOT attempt to manually light the pilot.
LIGHTING THE MAIN BURNERS
1.
Turn “OFF” electric power to unit.
2.
Turn room thermostat to lowest setting.
3.
Turn gas valve counter-clockwise to “ON” position (see
Figure 29).
4.
Turn “ON” electric power to unit.
5.
If thermostat set temperature is above room temperature, the main burners will ignite. If a second stage of
heat is called for, the main burners for second stage heat
will ignite for the second stage heat.
SHUT DOWN
1.
Set the thermostat to the lowest temperature setting.
2.
Turn “OFF” all electric power to unit.
3.
Open gas heat access panel.
4.
Turn gas valve clockwise to “OFF” position (See Figure
29).
MANIFOLD GAS PRESSURE ADJUSTMENT
This gas furnace has two heat stages. Therefore, the gas
valve has two adjustment screws located under a plastic protective cover. The second stage (100% input) adjustment
screw is adjacent to the “HI” marking on the valve and the
first stage (60% input) adjustment screw is located adjacent
to the “LO” marking on the valve (See Figure 29).
Manifold pressure adjustment procedure.
Adjust second stage (100% input) pressure first, then adjust
first stage (60% input) pressure.
1.
Turn off all power to the unit.
2.
Using the outlet pressure port on the gas valve, connect
a manometer to monitor the manifold pressure.
After the entire control circuit has been energized and the
heating section is operating, make the following checks:
3.
Remove plastic cap covering HI and LO pressure adjustment screws.
1.
4.
Turn on power to the unit.
5.
Set thermostat to call for second stage heat and start furnace.
6.
If necessary, using a screwdriver, turn the second stage
adjustment screw (adjacent to the “HI” marking on the
valve) clockwise to increase manifold pressure or counterclockwise to decrease manifold pressure. Be sure
not to over-fire the unit on second stage.
7.
After the high manifold pressure has been checked,
adjust the thermostat to call for first stage heat.
8.
If necessary, using a screwdriver, turn the first stage
adjustment screw (adjacent to the “LO” marking on the
POST START CHECKLIST
Check for gas leaks in the unit piping as well as the supply piping.
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly could
result in serious injury, death or property damage.
Never test for gas leaks with an open flame. use a
commercially available soap solution made specifically for the detection of leaks to check all connections. A fire or explosion may result causing property
damage, personal injury or loss of life.
Johnson Controls Unitary Products
67
264975-BIM-B-1208
valve) clockwise to increase manifold pressure or
counterclockwise to decrease manifold pressure. Be
sure not to under-fire the unit on first stage.
3.
Even when the thermostat is calling for first stage heat,
the unit will light on second stage and will run on Second
stage for 1 minute. Allow this one-minute time period to
expire and be certain the unit is running on first stage.
4.
NOTE: When using natural gas, the manifold pressure for
second stage (100% input) should be 3.5 IWG ±
0.3. The manifold pressure for first stage (60%
input) when using natural gas should be 1.5 IWG ±
0.3.
Measure the time needed for one revolution of the hand
on the smallest dial on the meter. A typical gas meter
has a 1/2 or a 1 cubic foot test dial.
5.
Using the number of seconds it takes for one revolution
of the dial, calculate the cubic feet of gas consumed per
hour (See example below).
TABLE 69: GAS HEAT STAGES
6.
If necessary, adjust the low pressure regulator as discussed in the section “Manifold Gas Pressure Adjustment”. Be sure not to under-fire the furnace on first
stage. If in doubt, it is better to leave the first stage of the
furnace slightly over-fired (greater than 60% input).
Repeat Steps 1-6.
9.
Once pressure has been checked, replace the plastic
cap covering the HI and LO pressure adjustment screws.
# of Burner Tubes
2nd Stage
Input (100%
Btuh)
1st Stage
Input (60%
Btuh)
4
120,000
72,000
6
180,000
108,000
8
240,000
144,000
CHECKING GAS INPUT
NATURAL GAS
TABLE 70: GAS RATE CUBIC FEET PER HOUR
Seconds
for One
Rev.
Size of Test Dial
1/2 cu. ft.
1 cu. ft.
10
180
360
This unit has two stages of gas heat. The first stage is 60% of
the full fire input and is considered the minimum input for the
furnace. The intended input for each furnace is shown in the
table below. The following Table applies to units operating on
60 Hz power only.
12
150
300
14
129
257
16
113
225
18
100
200
20
90
180
To determine the rate of gas flow (Second Stage).
22
82
164
24
75
150
26
69
138
28
64
129
30
60
120
32
56
113
34
53
106
Measure the time needed for one revolution of the hand
on the smallest dial on the meter. A typical gas meter
has a 1/2 or a 1 cubic foot test dial.
36
50
100
38
47
95
40
45
90
Using the number of seconds it takes for one revolution
of the dial, calculate the cubic feet of gas consumed per
hour. (See example below).
42
43
86
44
41
82
46
39
78
48
37
75
50
36
72
52
35
69
54
34
67
56
32
64
58
31
62
60
30
60
1.
2.
3.
4.
5.
Turn off all other gas appliances connected to the gas
meter.
Turn on the furnace and make sure the thermostat is
calling for Second stage (100% input) heat.
If necessary, adjust the high pressure regulator as discussed in the section “Manifold Gas Pressure Adjustment”. Be sure not to over-fire the furnace on Second
stage. If in doubt, it is better to leave the Second stage of
the furnace slightly under-fired. Repeat Steps 1-5.
To determine the rate of gas flow (First Stage)
1.
Turn off all other gas appliances connected to the gas
meter.
2.
Turn on the furnace and make sure the thermostat is
calling for first stage (60% input) heat.
68
NOTE: To find the Btu input, multiply the number of cubic
feet of gas consumed per hour by the Btu content of
the gas in your particular locality (contact your gas
company for this information as it varies widely from
area to area).
Johnson Controls Unitary Products
264975-BIM-B-1208
EXAMPLE:
By actual measurement, it takes 19 seconds for the hand on
a 1 cubic foot dial to make a revolution with a 192,000 Btuh
furnace running. To determine rotations per minute, divide 60
by 19 = 3.16. To calculate rotations per hour, multiply 3.16 •
60 = 189.6. Multiply 189.6 • 1 (0.5 if using a 1/2 cubic foot
dial) = 189.6. Multiply 189.6 • (the Btu rating of the gas). For
this example, assume the gas has a Btu rating of 1050
Btu/ft.3. The result of 199,000 Btuh is within 5% of the
192,000 Btuh rating of the furnace.
2.
Remove the screws holding each end of the manifold to
the manifold supports.
3.
Disconnect wiring to the gas valves and spark igniter(s).
Remove the manifold & gas valve assembly. Orifices can
now be inspected and/or replaced.
To service burners, complete step 4.
4.
Remove the heat shield on top of the manifold supports.
Burners are now accessible for inspection and/or
replacement.
ADJUSTMENT OF TEMPERATURE RISE
NOTE: Reverse the above procedure to replace the assemblies.
The temperature rise (the difference of temperature between
the return air and the heated air from the furnace) must lie
within the range shown on the CSA rating plate and the data
in Table 32.
Make sure that burners are level and seat at the rear of the
gas orifice.
H IG H & L O W
G A S A D J U S T M E N T
After the temperature rise has been determined, the CFM can
be calculated as follows:
0.8
CFM = Btu Input • ----------------------------( 1.08 ⋅ Δ°F )
After about 20 minutes of operation, determine the furnace
temperature rise. Take readings of both the return air and the
heated air in the ducts (about 6 feet from the furnace) where
they will not be affected by radiant heat. Increase the blower
CFM to decrease the temperature rise; decrease the blower
CFM to increase the rise (See ’SUPPLY AIR DRIVE
ADJUSTMENT’).
H I
L O
O N
IN L E T
P R E S S U R E
T A P
O F F
M A T E -N -L O C K
C O N N E C T O R S
O U T L E T
P R E S S U R E
T A P
NOTE: Each gas heat exchanger size has a minimum
allowable CFM. Below this CFM, the limit will open.
M V
BURNERS/ORIFICES INSPECTION/SERVICING
C
H I
Before checking or changing burners, pilot or orifices,
CLOSE MAIN MANUAL SHUT-OFF VALVE AND SHUT OFF
ALL POWER TO THE UNIT.
1.
Open the union fitting just upstream of the unit gas valve
and downstream from the main manual shut-off valve in
the gas supply line.
Johnson Controls Unitary Products
FIGURE 29 : TYPICAL GAS VALVE
69
264975-BIM-B-1208
CHARGING THE UNIT
When charging each system, superheat data should be taken
at the compressor inlet.
These units should be charged using the superheat method.
Super heat charging data is shown in Tables 71 thru 79.
TABLE 71: DL-06 (6.5 TON) STANDARD EFFICIENCY SUPERHEAT CHARGING
Superheat at Compressor Suction (°F)
Airflow = 2500 CFM
Outdoor
Temp (°F)
Indoor WB Temp (°F)
55
57
59
61
63
65
67
69
71
73
75
65
21.9
22.6
23.2
23.9
24.6
25.3
26.0
27.4
28.9
30.4
31.9
70
18.1
19.1
20.0
21.0
22.0
22.9
23.9
25.5
27.2
28.9
30.5
75
14.4
15.6
16.8
18.1
19.3
20.6
21.8
23.7
25.5
27.3
29.1
80
10.6
12.1
13.7
15.2
16.7
18.2
19.8
21.8
23.8
25.8
27.8
85
6.8
8.7
10.5
12.3
14.1
15.9
17.7
19.9
22.1
24.2
26.4
90
-
6.2
8.0
9.8
11.6
13.4
15.3
17.8
20.4
23.0
25.5
95
-
-
5.6
7.4
9.2
11.0
12.8
15.8
18.7
21.7
24.6
100
-
-
5.1
6.5
7.8
9.2
10.5
13.2
16.0
18.7
21.4
105
-
-
-
5.6
6.5
7.4
8.3
10.7
13.2
15.7
18.2
110
-
-
-
-
5.2
5.6
6.0
8.2
10.5
12.7
14.9
115
-
-
-
-
-
-
-
5.7
7.7
9.7
11.7
TABLE 72: DL-07 (7.5 TON) STANDARD EFFICIENCY SUPERHEAT CHARGING
Superheat at Compressor Suction (°F)
Airflow = 3000 CFM
Outdoor
Temp (°F)
70
Indoor WB Temp (°F)
55
57
59
61
63
65
67
69
71
73
75
65
-
6.4
8.7
10.9
13.2
15.4
17.7
19.8
21.9
24.1
26.2
70
-
6.3
8.5
10.7
12.9
15.1
17.3
19.2
21.1
23.0
24.9
75
-
6.1
8.3
10.4
12.6
14.7
16.9
18.6
20.2
21.9
23.5
80
-
6.0
8.1
10.2
12.3
14.4
16.5
17.9
19.4
20.8
22.2
85
-
5.8
7.9
9.9
12.0
14.0
16.1
17.3
18.5
19.7
20.9
90
-
5.7
7.7
9.7
11.7
13.7
15.7
16.3
16.9
17.5
18.1
95
-
5.5
7.5
9.4
11.4
13.3
15.3
15.3
15.3
15.3
15.3
100
-
-
6.2
7.8
9.3
10.8
12.4
12.4
12.4
12.5
12.5
105
-
-
-
6.1
7.2
8.3
9.4
9.5
9.6
9.6
9.7
110
-
-
-
-
5.1
5.8
6.5
6.6
6.7
6.8
6.9
115
-
-
-
-
-
-
-
-
-
-
-
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 73: DL-08 (8.5 TON) STANDARD EFFICIENCY SUPERHEAT CHARGING
Superheat at Compressor Suction (°F)
Airflow = 3400 CFM
Outdoor
Temp (°F)
Indoor WB Temp (°F)
55
57
59
61
63
65
67
69
71
73
75
65
17.0
19.1
21.2
23.3
25.4
27.5
29.6
31.4
33.1
34.9
36.6
70
14.6
16.6
18.6
20.6
22.6
24.6
26.7
28.4
30.1
31.8
33.6
75
12.1
14.1
16.0
17.9
19.8
21.8
23.7
25.4
27.1
28.8
30.5
80
9.7
11.5
13.4
15.2
17.1
18.9
20.8
22.4
24.1
25.8
27.4
85
7.2
9.0
10.8
12.5
14.3
16.0
17.8
19.4
21.1
22.7
24.4
90
-
-
6.6
8.7
10.7
12.7
14.8
16.7
18.7
20.7
22.7
95
-
-
-
-
7.1
9.4
11.7
14.0
16.3
18.7
21.0
100
-
-
-
-
5.3
7.0
8.8
11.0
13.2
15.5
17.7
105
-
-
-
-
-
-
5.8
8.0
10.1
12.3
14.4
110
-
-
-
-
-
-
-
-
7.0
9.1
11.1
115
-
-
-
-
-
-
-
-
-
5.9
7.8
TABLE 74: DL -10 (10 TON) STANDARD EFFICIENCY SUPERHEAT CHARGING
Superheat at Compressor Suction (°F)
Airflow = 4000 CFM
Outdoor
Temp (°F)
Indoor WB Temp (°F)
55
57
59
61
63
65
67
69
71
73
75
65
19.6
20.8
22.0
23.2
24.4
25.6
26.9
28.4
29.9
31.4
32.9
70
14.4
16.0
17.5
19.0
20.5
22.0
23.5
25.4
27.3
29.2
31.0
75
9.3
11.1
12.9
14.7
16.6
18.4
20.2
22.4
24.7
26.9
29.1
80
-
6.3
8.4
10.5
12.6
14.8
16.9
19.5
22.0
24.6
27.2
85
-
-
-
6.3
8.7
11.1
13.6
16.5
19.4
22.4
25.3
90
-
-
-
5.6
7.8
9.9
12.0
15.0
17.9
20.8
23.7
95
-
-
-
-
6.8
8.7
10.5
13.4
16.3
19.3
22.2
100
-
-
-
-
5.3
6.7
8.1
10.8
13.5
16.2
18.9
105
-
-
-
-
-
-
5.7
8.1
10.6
13.1
15.5
110
-
-
-
-
-
-
-
5.5
7.7
10.0
12.2
115
-
-
-
-
-
-
-
-
-
6.9
8.9
Johnson Controls Unitary Products
71
264975-BIM-B-1208
TABLE 75: DL-12 (12.5 TON) STANDARD EFFICIENCY SUPERHEAT CHARGING
Superheat at Compressor Suction (°F)
Airflow = 5000 CFM
Outdoor
Temp (°F)
Indoor WB Temp (°F)
55
57
59
61
63
65
67
69
71
73
75
65
33.9
34.5
35.1
35.7
36.3
36.9
37.5
38.1
38.7
39.3
39.9
70
30.2
31.0
31.8
32.7
33.5
34.3
35.2
36.0
36.8
37.7
38.5
75
26.4
27.5
28.6
29.6
30.7
31.8
32.8
33.9
35.0
36.0
37.1
80
23.5
24.7
26.0
27.2
28.4
29.7
30.9
32.1
33.4
34.6
35.8
85
20.6
22.0
23.4
24.8
26.2
27.6
29.0
30.4
31.8
33.2
34.6
90
17.2
18.8
20.3
21.9
23.5
25.0
26.6
28.2
29.7
31.3
32.9
95
13.8
15.5
17.2
19.0
20.7
22.4
24.2
25.9
27.6
29.4
31.1
100
9.9
11.8
13.6
15.5
17.4
19.2
21.1
23.0
24.8
26.7
28.6
105
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
26.0
110
4.8
6.5
8.2
9.8
11.5
13.2
14.8
16.5
18.2
19.8
21.5
115
3.7
5.0
6.3
7.7
9.0
10.3
11.7
13.0
14.3
15.7
17.0
TABLE 76: DU-06 (6.5 TON) HIGH EFFICIENCY SUPERHEAT CHARGING
Superheat at Compressor Suction (°F)
Airflow = 2500 CFM
Outdoor
Temp (°F)
72
Indoor WB Temp (°F)
55
57
59
61
63
65
67
69
71
73
75
65
12.0
15.8
19.6
23.4
27.2
31.0
34.8
38.1
41.4
44.8
48.1
70
11.6
14.9
18.3
21.6
24.9
28.2
31.6
34.3
37.1
39.9
42.7
75
11.2
14.1
16.9
19.8
22.6
25.5
28.3
30.5
32.8
35.0
37.3
80
10.8
13.2
15.6
17.9
20.3
22.7
25.1
26.8
28.5
30.2
31.9
85
10.4
12.3
14.2
16.1
18.0
19.9
21.8
23.0
24.1
25.3
26.4
90
-
6.1
8.3
10.4
12.5
14.7
16.8
19.0
21.2
23.4
25.6
95
-
-
-
-
7.1
9.4
11.8
15.0
18.3
21.5
24.8
100
-
-
-
-
5.3
7.1
8.9
11.3
13.7
16.1
18.6
105
-
-
-
-
-
-
5.9
7.5
9.1
10.8
12.4
110
-
-
-
-
-
-
-
-
-
5.4
6.2
115
-
-
-
-
-
-
-
-
-
-
-
Johnson Controls Unitary Products
264975-BIM-B-1208
TABLE 77: DU-07 (7.5 TON) HIGH EFFICIENCY SUPERHEAT CHARGING
Superheat at Compressor Suction (°F)
Airflow = 3000 CFM
Outdoor
Temp (°F)
Indoor WB Temp (°F)
55
57
59
61
63
65
67
69
71
73
75
65
37.1
37.6
38.1
38.5
39.0
39.4
39.9
40.0
40.1
40.2
40.3
70
32.1
32.8
33.4
34.1
34.8
35.5
36.2
36.4
36.7
37.0
37.3
75
27.0
27.9
28.8
29.7
30.6
31.5
32.4
32.9
33.4
33.9
34.4
80
21.9
23.1
24.2
25.3
26.4
27.5
28.7
29.3
30.0
30.7
31.4
85
16.9
18.2
19.5
20.9
22.2
23.6
24.9
25.8
26.7
27.5
28.4
90
7.3
9.6
11.8
14.0
16.2
18.4
20.6
22.3
24.1
25.8
27.6
95
-
-
-
7.0
10.1
13.1
16.2
18.8
21.5
24.1
26.8
100
-
-
-
5.4
7.8
10.2
12.6
15.3
18.0
20.7
23.4
20.1
105
-
-
-
-
5.5
7.2
8.9
11.7
14.5
17.3
110
-
-
-
-
-
-
5.3
8.1
11.0
13.9
16.8
115
-
-
-
-
-
-
-
-
7.5
10.5
13.4
TABLE 78: DU-08 (8.5 TON) HIGH EFFICIENCY SUPERHEAT CHARGING
Superheat at Compressor Suction (°F)
Airflow = 3000 CFM
Outdoor
Temp (°F)
Indoor WB Temp (°F)
55
57
59
61
63
65
67
69
71
73
75
65
29.9
31.4
32.9
34.4
35.8
37.3
38.8
39.9
41.0
42.2
43.3
70
27.5
29.0
30.5
32.0
33.5
35.0
36.5
37.4
38.4
39.3
40.3
75
25.1
26.7
28.2
29.7
31.2
32.7
34.2
35.0
35.7
36.5
37.2
80
22.8
24.3
25.8
27.3
28.9
30.4
31.9
32.5
33.1
33.6
34.2
85
20.4
21.9
23.4
25.0
26.5
28.1
29.6
30.0
30.4
30.8
31.2
90
12.1
14.4
16.6
18.9
21.2
23.5
25.8
26.9
28.0
29.1
30.2
95
-
6.8
9.8
12.9
15.9
19.0
22.0
23.8
25.6
27.4
29.2
100
-
5.3
7.6
9.8
12.1
14.3
16.6
19.1
21.7
24.3
26.9
105
-
-
5.3
6.7
8.2
9.6
11.1
14.5
17.8
21.2
24.5
110
-
-
-
-
-
-
5.7
9.8
13.9
18.1
22.2
115
-
-
-
-
-
-
-
5.1
10.0
15.0
19.9
DU-10 (10 ton) high efficiency unit uses TXV. Charge the unit to 10° subcooling.
TABLE 79: DU-12 (12.5 TON) HIGH EFFICIENCY SUPERHEAT CHARGING
Superheat at Compressor Suction (°F)
Airflow = 5000 CFM
Outdoor
Temp (°F)
Indoor WB Temp (°F)
55
57
59
61
63
65
67
69
71
73
75
65
7.9
10.7
13.6
16.4
19.3
22.2
25.0
26.9
28.7
30.5
32.4
70
7.3
9.7
12.2
14.6
17.1
19.5
22.0
24.2
26.5
28.8
31.0
75
6.7
8.7
10.8
12.8
14.8
16.9
18.9
21.6
24.3
27.0
29.7
80
6.1
7.7
9.3
11.0
12.6
14.3
15.9
19.0
22.1
25.2
28.3
85
5.5
6.7
7.9
9.2
10.4
11.6
12.9
16.4
19.9
23.5
27.0
90
5.6
6.5
7.4
8.4
9.3
10.2
11.2
14.9
18.7
22.5
26.2
95
5.6
6.3
6.9
7.6
8.2
8.8
9.5
13.5
17.5
21.5
25.5
100
5.2
5.8
6.5
7.1
7.8
8.4
9.0
12.3
15.6
18.8
22.1
105
-
5.4
6.0
6.7
7.3
8.0
8.6
11.1
13.7
16.2
18.7
110
-
-
5.6
6.2
6.9
7.5
8.2
10.0
11.8
13.6
15.4
115
-
-
5.1
5.8
6.4
7.1
7.7
8.8
9.9
10.9
12.0
Johnson Controls Unitary Products
73
264975-BIM-B-1208
TROUBLESHOOTING
DL/DU FLASH CODES
Troubleshooting of components may require opening the electrical control box with the power connected to the unit. Use extreme care when
working with live circuits! Check the unit nameplate for the correct line voltage and set the voltmeter to the correct range before making any
connections with line terminals.
When not necessary, shut off all electric power to the
unit prior to any of the following maintenance procedures so as to prevent personal injury.
Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dangerous operation which could cause injury to person
and/or damage unit components. Verify proper operation after servicing.
Various flash codes are utilized by the unit control board
(UCB) to aid in troubleshooting. Flash codes are
distinguished by the short on and off cycle used
(approximately 200ms on and 200ms off). To show normal
operation, the control board flashes a 1 second on, 1 second
off "heartbeat" during normal operation. This is to verify that
the UCB is functioning correctly. Do not confuse this with an
error flash code. To prevent confusion, a 1-flash, flash code
is not used.
Alarm condition codes are flashed on the UCB lower left Red
LED, See Figure 30. While the alarm code is being flashed, it
will also be shown by the other LEDs: lit continuously while
the alarm is being flashed. The total of the continuously lit
LEDs equates to the number of flashes, and is shown in the
table. Pressing and releasing the LAST ERROR button on
the UCB can check the alarm history. The UCB will cycle
through the last five (5) alarms, most recent to oldest,
separating each alarm flash code by approximately 2
seconds. In all cases, a flashing Green LED will be used to
indicate non-alarm condition.
In some cases, it may be necessary to "zero" the ASCD for
the compressors in order to perform troubleshooting. To reset
all ASCDs for one cycle, press and release the UCB TEST/
RESET button once.
Flash codes that do and do not represent alarms are listed in
Table 80.
TABLE 80: UNIT CONTROL BOARD FLASH CODES
FLASH CODE
On Steady
1 Flash
RED
LED
8
RED
LED
4
RED
LED
2
RED
LED
1
This is a Control Failure
-
-
-
-
-
Not Applicable
-
-
-
-
-
Flashing
Off
Off
On
Off
Off
Off
Off
On
On
2 Flashes
Control waiting ASCD1
3 Flashes
HPS1 Compressor Lockout
4 Flashes
HPS2 Compressor Lockout
Off
Off
On
Off
Off
5 Flashes
LPS1 Compressor Lockout
Off
Off
On
Off
On
6 Flashes
LPS2 Compressor Lockout
Off
Off
On
On
Off
7 Flashes
FS1 Compressor Lockout
Off
Off
On
On
On
8 Flashes
FS2 Compressor Lockout
Off
On
Off
Off
Off
9 Flashes
Ignition Control Locked Out / Ignition Control Failure
Off
On
Off
Off
On
Flashing
On
Off
On
Off
Flashing
On
Off
On
On
10 Flashes
11 Flashes
12 Flashes
Compressors Locked Out on Low Outdoor Air Temperature
Cooling1
Unit Locked Out due to Fan Overload Switch Failure
Off
On
On
Off
Off
Flashing
On
On
Off
On
EEPROM Storage Failure
Off
On
On
On
Off
No Power or Control Failure
Off
Off
Off
Off
Off
Compressor Held Off due to Low
14 Flashes
1.
1
Compressors locked out because the Economizer is using free
13 Flashes
OFF
74
GREEN
LED
16
DESCRIPTION
Voltage1
Non-alarm condition.
Johnson Controls Unitary Products
264975-BIM-B-1208
Check
Alarm
History
Reset All
ASCDs for
One Cycle
Non Alarm
Condition Green
LED Flashing
Current Alarm
Flashed
Red LED
FIGURE 30 - UNIT CONTROL BOARD
UNIT CONTROL BOARD OPTION SETUP
HEAT DELAY SETUP
OPTION BYTE SETUP
•
Enter the Option Setup mode by pushing the OPTION
SETUP / STORE button, and holding it for at least 2 seconds.
•
The green status LED (Option Byte) will be turned on
and the red status LED (Heat Delay) is turned off.
•
Press the COMM SETUP / SELECT button to toggle into
the Heat Delay Setup, the green LED will turn off and the
red LED for Heat Delay will turn on.
•
The 8, 4, 2 and 1 LEDs will then show the status of the
Heat Delay, (See Table 81). Press the UP or Down button to change the LED status to correspond to the
desired Heat Delay Value.
•
To save the current displayed value, push the OPTION
SETUP / STORE button and hold it for at least 2 seconds. When the value is saved, the red LED will flash a
few times and then normal display will resume.
•
Enter the Option Setup mode by pushing the OPTION
SETUP / STORE button, and holding it for at least 2 seconds.
•
The green status LED (Option Byte) will be turned on
and the red status LED (Heat Delay) is turned off.
•
The 8, 4, 2 and 1 LEDs will then show the status of the 4
labeled options ((8) Fan Off at Heat Start, (4) Low
Ambient Lockout, (2) Free Cooling Lockout, and (1)
Lead / Lag).
•
•
Press the UP or Down button to change the LED status
to correspond to the desired Option Setup.
To save the current displayed value, push the OPTION
SETUP / STORE button and hold it for at least 2 seconds. When the value is saved, the green LED will flash
a few times and then normal display will resume.
NOTE: While in either Setup mode, if no buttons are
pushed for 60 seconds, the3 display will revert to its
normal display, exiting the Option Setup mode.
When saving, the control board only saves the
parameters for the currently displayed mode
(Option Byte or Heat Delay).
Johnson Controls Unitary Products
NOTE: While in either Setup mode, if no buttons are
pushed for 60 seconds, the display will revert to its
normal display, exiting the Option Setup mode.
When saving, the control board only saves the
parameters for the currently displayed mode
(Option Byte or Heat Delay).
75
264975-BIM-B-1208
TABLE 81: HEAT DELAY
Heat
Fan On
Delay
60
60
60
60
45
45
45
45
30
30
30
30
0
0
0
Non-std
Heat
Fan Off
Delay
180
90
60
30
180
90
60
30
180
90
60
30
60
30
10
Non-std
TABLE 82: IGNITION CONTROL FLASH CODES
FLASHES
Red
LED 8
Red
LED 4
Red
LED 2
Red
LED 1
On
On
On
On
On
On
On
On
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
On
Off
Off
Off
Off
On
On
On
On
Off
Off
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
STEADY ON
Control Failure
HEARTBEAT
Normal Operation
CHECK
Control
1
Not Applicable
2
Pressure Switch
Stuck Closed
Pressure Switch
3
Pressure Switch Failed
To Close
Venter Pressure Switch
Vent Blocked
4
Limit Switch Open
Main Limit
AUX Limit
5
Flame Present With Gas
Off First Stage Gas Valve
Energized With W1 Off
Second Stage Gas Valve
Energized With First
Stage
Gas Valve Off
Gas Valve
6
Ignition Lockout
Gas Flow
Gas Pressure
Gas Valve
Flame Sensor
No Power Or Control
Failure
24VAC or Control
STEADY OFF
76
FAULT CONDITIONS
Johnson Controls Unitary Products
264975-BIM-B-1208
Monitored
Systems
Problem?
No
No
Call for
Heating?
Programming?
Yes
Yes
Program
Unit
Control
Board
Call for
Heat
Yes
Trip/Failure
Loss of
Call for
Heating?
No
Yes
Heat Off
No
Call for 2nd
Stage
Cooling
No
Energize ID
Blower Motor
Monitor
Call for
Cooling?
Yes
First
Stage?
Yes
No
Yes
No
Turn off ID
Blower Motor
Yes
No
Fan on
>30 secs?
Yes
Yes
No
Call for 1st
Stage
Cooling
Fan off
>10 secs?
No
Lossof Call
for ID Blower?
Call for
ID Blower?
No
Loss of Call
for Cooling?
Yes
Cool Off
FIGURE 31 - BASIC TROUBLESHOOTING FLOWCHART
Power to
Unit
Call for
heat?
No
Initialize ASCD
Yes
Voltage @
Gas Valve?
Yes
No
Energize ID
Blower
Montior
FIGURE 32 - POWER ON FLOW CHART
Johnson Controls Unitary Products
77
264975-BIM-B-1208
H P
S w itc h
O p e n 1
N o
L o s s o f
L S In p u t
T r ip /F a ilu r e
L P
S w itc h O p e n
> 5 S e c s2
N o
Y e s
Y e s
T
c o m
in itia
in c r e a
v a
E n e r g iz e b lo w e r :
in c r e a s e in c id e n t
v a lu e b y 1
N o
Y e s
u rn
p r
te
s e
lv e
o ff
e s s o r;
A S C D ;
in c id e n t
b y 1
N o
F re e z e s ta t
O p e n ?1
Y e s
T u rn o ff
C o m p re s s o r,
in itia te A S C D ;
in c r e a s e in c id e n t
v a lu e b y 1
T u rn
c o m p r
in itia te
in c r e a s e
v a lu e
o ff
e s s o r,
A S C D ;
in c id e n t
b y 1
N o
In c id e n t
v a lu e > = 3 ?
N o
Y e s
N o
L S in p u t
r e g a in e d ?
Y e s
L o c k o n b lo w e r ;
fla g a la r m
N o
In c id e n t
v a lu e > = 3
Y e s
N o
In c id e n t
v a lu e > = 3
Y e s
L o c k -o u t
c o m p r e s s o r , fla g
a la r m
L o a d F o ffD
In c id e n t
v a lu e > = 3
Y e s
L o c k -o u t
c o m p r e s s o r , fla g
a la r m
L o c k
c o m p re s
o ff ID b lo
o ff c o n
fa n s , fla
-o u t
s o r,
w e r,
d e n s
g a la
tu rn
tu rn
e r
rm
M o n ito r
L o s s o f
F O S in p u t
> 5 S e c s ?
C a ll fo r
H e a t w /o u t G V
v o lta g e ?
N o
Y e s
Y e s
T u rn
c o m p r
c o n d e n
in itia te
N o
o ff fa n
e s s o r &
s e r fa n s ;
A S C D
G V
v o lta g e
w /o u t c a ll fo r
h e a t?
N o
G V v o lta g e
> 5 m in ?
Y e s
F la g A la r m
N o
v o lta g e > 5
m in ?
N o
Y e s
F la g a la r m , lo c k
o n ID b lo w e r
N o
In c id e n t
v a lu e > = 3
F O S in p u t
r e g a in e d ?
N o
Y e s
c o m
o ff
o
fa
L o c k -o
p re s s o
ID b lo w
ff c o n d e
n s , fla g
N o
F O S in p u t > 1 5
m in u te s ?
N o
Y e s
u t
rs ,
e r,
n s
a la
tu rn
tu rn
e r
rm
Y e s
In c r e a s e in c id e n t
v a lu e b y 1
F la g a la r m , tu r n o n
X lin e
Y e s
L o s s o f G V
V o lta g e ?
N o
E n e rg
b lo w e r ,
O ff D e
h e a
iz e ID
lo a d 'F a n
la y ' fo r
tin g
M o n ito r
1 T h e
2 T h e
a n d
lo n g
c o n
lo w
a d d
e r h
tro l b o a rd
-p re s s u re
itio n a l 3 0
a n d le s th
o n ly
s w itc
s e c o
e lo w
m
h
n d
-p
o n ito r s
is n o t m
s , th e c
re s s u re
th e in
o n ito
o n tro
s w itc
p u t
re d
l b o
h d
w h e n th e c o m p re s s o r re a
fo r th e fir s t 3 0 s e c o n d s o f
a r d tu r n s o ff th e a s s o c ia te
iffe r e n tly th a n o th e r in p u ts
lly is e n e r g iz e d .
c o m p r e s s o r a c tiv ity . T h e c o n tr o l b o a r d th e n m o n ito r s th e s w itc h to e n s u r e it c lo s e s . If th e s w itc h r e m a in s o p e n
d c o m p r e s s o r a n d in itia te s th e A S C D . O n c e it h a s c lo s e d d u r in g th e s ta r t u p p e r io d , th e c o n tr o l b o a r d n o
.
FIGURE 33 - TRIP FAILURE FLOW CHART
78
Johnson Controls Unitary Products
264975-BIM-B-1208
COOLING TROUBLESHOOTING GUIDE
On calls for cooling, if the compressors are operating but the
supply air blower motor does not energize after a short delay
(the room thermostat fan switch is in the “AUTO” position):
1.
If installed, check the position of the economizer blades.
If the blades are open, the economizer is providing free
cooling and the compressors will not immediately operate. If both stages of cooling are requested simultaneously and the economizer provides free cooling,
following a short delay compressor #1 will be energized
unless it is locked out. If compressor #1 is locked out,
compressor #2 is energized. Compressor #2 is always
energized in place of compressor #1 when compressor
#1 is requested but locked out.
2.
If no economizer is installed or the economizer is not
opening to provide free cooling and compressor #1 does
not energize on a call for cooling, check for line voltage
at the compressor contactor, M1, and that the contactor
is pulled in. Check for loose wiring between the contactor and the compressor.
3.
If M3 is not pulled in, check for 24 volts at the M3 coil. If
24 volts are present at M3 but M3 is not pulled in,
replace the contactor.
If M1 is pulled in and voltage is supplied at M1, lightly
touch the compressor housing. If it is hot, the compressor may be off on inherent protection. Cancel any calls
for cooling and wait for the internal overload to reset.
Test again when cool.
4.
Failing the above, if there is line voltage supplied at M3,
M3 is pulled in, and the supply air blower motor still does
not operate, replace the motor.
If M1 is not pulled in, check for 24 volts at the M1 coil. If
24 volts are present and M1 is not pulled in, replace the
contactor.
5.
If 24 volts is not present at M3, check that 24 volts is
present at the UCB supply air blower motor terminal,
“FAN”. If 24 volts is present at the FAN, check for loose
wiring between the UCB and M3.
Failing the above, if voltage is supplied at M1, M1 is
pulled in, and the compressor still does not operate,
replace the compressor.
6.
If 24 volts is not present at M1, check for 24 volts at the
UCB terminal, C1. If 24 volts is present, check for loose
wiring between C1 and the compressor contactor.
7.
If 24 volts is not present at the C1 terminal, check for 24
volts from the room thermostat at the UCB Y1 terminal. If
24 volts is not present from the room thermostat, check
for the following:
1.
Turn the thermostat fan switch to the ON position. If the
supply air blower motor does not energize, go to Step 3.
2.
If the blower motor runs with the fan switch in the ON
position but will not run after the first compressor has
energized when the fan switch is in the AUTO position,
check the room thermostat for contact between R and G
in the AUTO position during calls for cooling.
3.
If the supply air blower motor does not energize when
the fan switch is set to ON, check that line voltage is
being supplied to the contacts of the M3, contactor, and
that the contactor is pulled in. Check for loose wiring
between the contactor and the supply air blower motor.
4.
If M3 is pulled in and voltage is supplied to M3, lightly
touch the supply air blower motor housing. If it is hot, the
motor may be off on internal protection. Cancel any
thermostat calls and set the fan switch to AUTO. Wait for
the internal overload to reset. Test again when cool.
5.
6.
7.
8.
If 24 volts is not present at the “FAN” terminal, check for
24 volts from the room thermostat. If 24 volts are not
present from the room thermostat, check for the following:
a.
9.
On calls for cooling, the supply air blower motor is operating
but compressor #1 is not (the room thermostat fan switch is in
the “AUTO” position):
Proper operation of the room thermostat (contact
between R and G with the fan switch in the ON position and in the AUTO position during operation
calls).
a.
24 volts at the thermostat Y1 terminal
b.
Proper wiring between the room thermostat and the
UCB, i.e. Y1 to Y1, Y2 to Y2, and
b.
Proper wiring between the room thermostat and the
UCB, and
c.
Loose wiring from the room thermostat to the UCB
c.
Loose wiring from the room thermostat to the UCB
8.
If 24 volts is present at the UCB Y1 terminal, the compressor may be out due to an open high-pressure switch,
low-pressure switch, or freezestat. Check for 24 volts at
the HPS1, LPS1, and FS1 terminals of the UCB. If a
switch has opened, there should be a voltage potential
between the UCB terminals, e.g. if LPS1 has opened,
there will be a 24-volt potential between the LPS1 terminals.
9.
If 24 volts is present at the UCB Y1 terminal and none of
the protection switches have opened, the UCB may have
If 24 volts is present at the room thermostat but not at the
UCB, check for proper wiring between the thermostat
and the UCB, i.e. that the thermostat G terminal is connected to the G terminal of the UCB, and for loose wiring.
10. If the thermostat and UCB are properly wired, replace
the UCB.
Johnson Controls Unitary Products
79
264975-BIM-B-1208
locked out the compressor for repeat trips. The UCB
should be flashing an alarm code. If not, press and
release the ALARMS button on the UCB. The UCB will
flash the last five alarms on the LED. If the compressor is
locked out, cancel any call for cooling. This will reset any
compressor lock outs.
NOTE: While the above step will reset any lockouts, compressor #1 may be held off for the ASCD. See the
next step.
10. If 24 volts is present at the UCB Y1 terminal and none of
the switches are open and the compressor is not locked
out, the UCB may have the compressor in an ASCD.
Check the LED for an indication of an ASCD cycle. The
ASCD should time out within 5 minutes. Press and
release the TEST button to reset all ASCDs.
11. If 24 volts is present at the UCB Y1 terminal and the
compressor is not out due to a protective switch trip,
repeat trip lock out, or ASCD, the economizer terminals
of the UCB may be improperly wired. Check for 24 volts
at the Y1 “OUT” terminal of the UCB. If 24 volts is present, trace the wiring from Y1 “OUT” for incorrect wiring.
If 24 volts is not present at the Y1 “OUT” terminal, the
UCB must be replaced.
12. For units without economizers: If 24 volts is present at
the Y1 OUT terminal, check for 24 volts at the Y1
“ECON” terminal. If 24 volts is not present, check for
loose wiring from the Y1 “OUT” terminal to the Mate-NLock plug, the jumper in the Mate-N-Lock plug, and in
the wiring from the Mate-N-Lock plug to the Y1 “ECON”
terminal.
13. For units with economizers: If 24 volts is present at the
Y1 “OUT” terminal, check for 24 volts at the Y1 “ECON”
terminal. If 24 volts is not present, check for loose wiring
from the Y1 “OUT” terminal to the Mate-N-Lock plug, a
poor connection between the UCB and economizer
Mate-N-Lock plugs, loose wiring from the Mate-N-Lock
plug to the economizer, back to the Mate-N-Lock plug,
and from the Mate-N-Lock plug to the Y1 “ECON” terminal. If nothing is found, the economizer control may have
faulted and is failing to return the 24-volt “call” to the Y1
“ECON” terminal even though the economizer is not providing free cooling. To test, disconnect the Mate-N-Locks
and jumper between the WHITE and YELLOW wires of
the UCB’s Mate-N-Lock plug. If compressor #1 energizes, there is a fault in the economizer wiring or the
economizer control.
14. The UCB can be programmed to lock out compressor
operation during free cooling and in low ambient conditions. These options are not enabled by default. Local
distributors can test the UCB for this programming.
For units with factory installed economizers, the UCB is
programmed to lock out compressor operation when the
LAS set point is reached.
80
For units without factory installed or with field installed
economizers, the UCB allows compressor operation all
the time. This programming can be checked or changed
by the local distributor.
15. If none of the above corrected the error, test the integrity
of the UCB. Disconnect the C1 terminal wire and jumper
it to the Y1 terminal. DO NOT jump the Y1 to C1 terminals. If the compressor engages, the UCB has faulted.
16. If none of the above correct the error, replace the UCB.
On calls for the second stage of cooling, the supply air blower
motor and compressor #1 are operating but compressor #2 is
not (the room thermostat fan switch is in the “AUTO” position):
1.
If installed, check the position of the economizer blades.
If the blades are open, the economizer is providing free
cooling. If the second stage of cooling is requested, following a short delay, compressor #1 will be energized
unless it is locked out. Typically, compressor #2 is energized only during free cooling if the call for the second
stage of cooling persists for 20 minutes.
2.
Compressor #2 will not energize simultaneously with
compressor #1 if a call for both stages of cooling is
received. The UCB delays compressor #2 by 30 seconds to prevent a power surge. If after the delay compressor #2 does not energize on a second stage call for
cooling, check for line voltage at the compressor contactor, M2, and that the contactor is pulled in. Check for
loose wiring between the contactor and the compressor.
3.
If M2 is pulled in and voltage is supplied at M2, lightly
touch the compressor housing. If it is hot, the compressor may be off on inherent protection. Cancel any calls
for cooling and wait for the internal overload to reset.
Test again when cool.
4.
If M2 is not pulled in, check for 24 volts at the M2 coil. If
24 volts is present and M2 is not pulled in, replace the
contactor.
5.
Failing the above, if voltage is supplied at M2, M2 is
pulled in, and the compressor still does not operate,
replace the compressor.
6.
If 24 volts is not present at M2, check for 24 volts at the
UCB terminal, C2. If 24 volts are present, check for
loose wiring between C2 and the compressor contactor.
7.
If 24 volts is not present at the C2 terminal, check for 24
volts from the room thermostat at the UCB Y2 terminal. If
24 volts is not present from the room thermostat, check
for the following:
a.
24 volts at the thermostat Y2 terminal
b.
Proper wiring between the room thermostat and the
UCB, i.e. Y1 to Y1, Y2 to Y2, and
c.
Loose wiring from the room thermostat to the UCB
Johnson Controls Unitary Products
264975-BIM-B-1208
8.
9.
If 24 volts is present at the UCB Y2 terminal, the compressor may be out due to an open high-pressure switch,
low-pressure switch, or freezestat. Check for 24 volts at
the HPS2, LPS2, and FS2 terminals of the UCB. If a
switch has opened, there should be a voltage potential
between the UCB terminals, e.g. if LPS2 has opened,
there will be 24 volts of potential between the LPS2 terminals.
If 24 volts is present at the UCB Y2 terminal and none of
the protection switches have opened, the UCB may have
locked out the compressor for repeat trips. The UCB
should be flashing a code. If not, press and release the
ALARMS button on the UCB. The UCB will flash the last
five alarms on the LED. If the compressor is locked out,
remove any call for cooling at the thermostat or by disconnecting the thermostat wiring at the Y2 UCB terminal.
This will reset any compressor lock outs.
NOTE: While the above step will reset any lock outs, compressor #1 will be held off for the ASCD, and compressor #2 may be held off for a portion of the
ASCD. See the next step.
2.
Check for line voltage at the compressor contactor, M1,
and that the contactor is pulled in. Check for loose wiring
between the contactor and the compressor.
3.
If M1 is pulled in and voltage is supplied at M1, lightly
touch the compressor housing. If it is hot, the compressor may be off on inherent protection. Cancel any calls
for cooling and wait for the internal overload to reset.
Test again when cool.
4.
If M1 is not pulled in, check for 24 volts at the M1 coil. If
24 volts is present and M1 is not pulled in, replace the
contactor.
5.
Failing the above, if voltage is supplied at M1, M1 is
pulled in, and the compressor still does not operate,
replace the compressor.
6.
If 24 volts is not present at M1, check for 24 volts at the
UCB terminal, C1. If 24 volts is present, check for loose
wiring between C1 and the compressor contactor.
7.
If 24 volts is not present at the C1 terminal, check for 24
volts from the room thermostat at the UCB Y1 terminal.
If 24 volts are not present at the UCB Y1 terminal, the
UCB may have faulted. Check for 24 volts at the Y1
ECON terminal. If 24 volts is not present at Y1 “ECON”,
the UCB has faulted. The UCB should de-energize all
compressors on a loss of call for the first stage of cooling, i.e. a loss if 24 volts at the Y1 terminal.
8.
If 24 volts are present at the UCB Y1 terminal, the compressor may be out due to an open high-pressure switch,
low-pressure switch, or freezestat. Check for 24 volts at
the HPS1, LPS1, and FS1 terminals of the UCB. If a
switch has opened, there should be a voltage potential
between the UCB terminals, e.g. if LPS1 has opened,
there will be a 24-volt potential between the LPS1 terminals.
9.
If 24 volts is present at the UCB Y1 terminal and none of
the protection switches have opened, the UCB may have
locked out the compressor for repeat trips. The UCB
should be flashing a code. If not, press and release the
ALARMS button on the UCB. The UCB will flash the last
five alarms on the LED. If the compressor is locked out,
remove any call for cooling. This will reset any compressor lock outs.
10. If 24 volts is present at the UCB Y2 terminal and none of
the switches are open and the compressor is not locked
out, the UCB may have the compressor in an ASCD.
Check the LED for an indication of an ASCD cycle. The
ASCD should time out within 5 minutes. Press and
release the TEST button to reset all ASCDs.
11. The UCB can be programmed to lock out compressor
operation during free cooling and in low ambient conditions. These options are not enabled by default. Local
distributors can test the UCB for this programming.
For units with factory installed economizers, the UCB is
programmed to lock out compressor operation when the
LAS set point is reached.
For units without factory installed or with field installed
economizers, the UCB allows compressor operation all
the time. This programming can be checked or changed
by the local distributor.
12. If none of the above corrected the error, test the integrity
of the UCB. Disconnect the C2 terminal wire and jumper
it to the Y2 terminal. DO NOT jump the Y2 to C2 terminals. If the compressor engages, the UCB has faulted.
13. If none of the above correct the error, replace the UCB.
On a call for cooling, the supply air blower motor and compressor #2 are operating but compressor #1 is not (the room
thermostat fan switch is in the “AUTO” position):
1.
Compressor #2 is energized in place of compressor #1
when compressor #1 is unavailable for cooling calls.
Check the UCB for alarms indicating that compressor #1
is locked out. Press and release the ALARMS button if
the LED is not flashing an alarm.
Johnson Controls Unitary Products
NOTE: While the above step will reset any lock outs, compressor #2 will be held off for the ASCD, and compressor #1 may be held off for a portion of the
ASCD. See the next step.
10. If 24 volts is present at the UCB Y1 terminal and none of
the switches are open and the compressor is not locked
out, the UCB may have the compressor in an ASCD.
Check the LED for an indication of an ASCD cycle. The
ASCD should time out within 5 minutes. Press and
release the TEST button to reset all ASCDs.
81
264975-BIM-B-1208
11. If 24 volts is present at the UCB Y1 terminal and the
compressor is not out due to a protective switch trip,
repeat trip lock out, or ASCD, the economizer terminals
of the UCB may be improperly wired. Check for 24 volts
at the Y1 “OUT” terminal of the UCB. If 24 volts is present, trace the wiring from Y1 “OUT” for incorrect wiring.
If 24 volts is not present at the Y1 “OUT” terminal, the
UCB must be replaced.
12. For units without economizers: If 24 volts is present at
the Y1 “OUT” terminal, check for 24 volts at the Y1
“ECON” terminal. If 24 volts is not present, check for
loose wiring from the Y1 “OUT” terminal to the Mate-NLock plug, the jumper in the Mate-N-Lock plug, and in
the wiring from the Mate-N-Lock plug to the Y1 “ECON”
terminal.
For units with economizers:If 24 volts is present at the
Y1 “OUT” terminal, check for 24 volts at the Y1 “ECON”
terminal. If 24 volts is not present, check for loose wiring
from the Y1 “OUT” terminal to the Mate-N-Lock plug, a
poor connection between the UCB and economizer
Mate-N-Lock plugs, loose wiring from the Mate-N-Lock
plug to the economizer, back to the Mate-N-Lock plug,
and from the Mate-N-Lock plug to the Y1 “ECON”
terminal. The economizer control may have faulted and
is not returning the 24 volts to the Y1 “ECON” terminal
even though the economizer is not providing free
cooling. To test the economizer control, disconnect the
Mate-N-Locks and jumper between the WHITE and
YELLOW wires of the UCB’s Mate-N-Lock plug.
13. The UCB can be programmed to lock out compressor
operation during free cooling and in low ambient conditions. These options are not enabled by default. They
can be checked by local distributors.
The furnace may shut down on a high temperature
condition during the procedure. If this occurs, the
UCB energize the supply air blower motor until the
high temperature limit has reset. Caution should be
used at all times as the supply air blower may energize regardless of the room thermostat fan switch
position.
1.
Place the thermostat fan switch in the “ON” position. If
the supply air blower motor energizes, go to Step 9.
2.
If the supply air blower motor does not energize when
the fan switch is set to “ON,” check that line voltage is
being supplied to the contacts of the M3 contactor, and
that the contactor is pulled in. Check for loose wiring
between the contactor and the supply air blower motor.
3.
If M3 is pulled in and voltage is supplied at M3, lightly
touch the supply air blower motor housing. If it is hot, the
motor may be off on inherent protection. Cancel any
thermostat calls and set the fan switch to “AUTO”, wait
for the internal overload to reset. Test again when cool.
4.
If M3 is not pulled in, check for 24 volts at the M3 coil. If
24 volts is present at M3 but M3 is not pulled in, replace
the contactor.
5.
Failing the above, if there is line voltage supplied at M3,
M3 is pulled in, and the supply air blower motor still does
not operate, replace the motor.
6.
If 24 volts is not present at M3, check that 24 volts is
present at the supply air blower motor terminal on the
UCB. If 24 volts is present at the UCB terminal, check
for loose wiring between the UCB and M3.
For units with factory installed economizers, the UCB is
programmed to lock out compressor operation when the
LAS set point is reached.
a.
For units without factory installed or with field installed
economizers, the UCB allows compressor operation all
the time. This programming can be checked or changed
by the local distributor.
i.Proper operation of the room thermostat (contact
between R and G with the fan switch in the
“ON” position and in the “AUTO” position during
operation calls)
14. If none of the above corrected the error, test the integrity
of the UCB. Disconnect the C1 terminal wire and jumper
it to the Y1 terminal. DO NOT jump the Y1 to C1 terminals. If the compressor engages, the UCB has faulted.
ii.Proper wiring between the room thermostat and
the UCB, and
15. If none of the above correct the error, replace the UCB.
GAS HEAT TROUBLESHOOTING GUIDE
On calls for heating, the draft motor operates and the furnace
lights but the supply air blower motor does not energize after
a short delay (the room thermostat fan switch is in “AUTO”
position).
82
If 24 volts is not present at the UCB supply air
blower motor terminal, check for 24 volts from the
room thermostat. If 24 volts is not present from the
room thermostat, check for the following:
iii.Loose wiring from the room thermostat to the UCB
7.
If 24 volts is present at the room thermostat but not at the
UCB, check for proper wiring between the thermostat
and the UCB, i.e. that the thermostat G terminal is connected to the G terminal of the UCB, and for loose wiring.
8.
If the thermostat and UCB are properly wired, replace
the UCB.
Johnson Controls Unitary Products
264975-BIM-B-1208
9.
If the blower motor runs with the fan switch in the “ON”
position but does not run shortly after the furnace has
ignited when the fan switch is in the “AUTO” position,
check the room thermostat for contact between R and G
during “W1” calls.
On calls for heating, the supply air blower operates but the
draft motor does not (the room thermostat fan switch is in the
“AUTO” position).
1.
The draft motor has inherent protection. If the motor
shell is hot to the touch, wait for the internal overload to
reset.
2.
If the motor shell is cold with the room thermostat calling
for heat, check for line voltage at the motor leads. If line
voltage is present, replace the draft motor.
3.
If line voltage is not present, check for line voltage on the
ignition control at the “inducer” terminal draft motor relay
(DMR or DMC) contacts in the main control box and
check to see if the (DMR or DMC) is pulled in.
the either pressure or rollout switch is not closed. Or the
draft motor is not sufficiently evacuating the heat
exchanger tubes or the pressure switch has failed.
Check the operation of the pressure switch. Check the
line voltage to the unit; if line voltage is low, call the local
power company. If the problem persists, the draft motor
may need replacement.
4.
If the furnace is hot, it may be out on a high temperature
limit open; wait for limit reset.
5.
If all are intact replace the ICB.
The draft motor runs and the spark ignitor sparks at the
burner, but the burner does not ignite and a gas odor is not
detected at the draft motor outlet.
1.
Check to ensure gas is being supplied to the unit. Confirm that the gas pressure to the unit is within the proper
limits as described in the “POST START CHECKLIST”.
2.
Check the voltage at the gas valve and at the gas valve
terminals on the ICB. Check all wiring between the ICB
and the gas valve. Check to make sure the ground connections are intact.
3.
If 24 volts is present, remove the pilot burner and the orifice. The removal procedure is described in
“BURNER/ORIFICE INSPECTION/SERVICING.” Inspect
the orifice for obstruction. If it is clear, replace the gas
valve.
The draft motor runs but the furnace does not light and the
spark ignitor does not spark.
1.
Check for 24 volts at the spark ignitor from the ignition
control board (ICB). Check the 24-volt wiring from the
ICB to the spark ignitor. Check for 24 volts at the ICB
spark ignitor terminal.
2.
Check the ground wiring for the ICB and the gas valve is
intact and making good electrical connection. Check the
ceramic insulator on the spark ignitor for breaks or
cracks. Replace the spark ignitor if damaged.
Main burners light but exhibit erratic flame characteristics.
1.
3.
With the draft motor running, check for 24 volts at the
pressure switch terminal on the ICB. If not present,
check for 24 volts on the terminal from the pressure
switch. If present, go to step 4. If 24 volts is not present,
Johnson Controls Unitary Products
Check the main burner orifices for obstruction and alignment. The removal procedure is described in
“BURNER/ORIFICE INSPECTION/SERVICING”. Clean
or replace burner orifices and burners as needed.
83
Subject to change without notice. Printed in U.S.A.
Copyright © 2009 by Johnson Controls, Inc. All rights reserved.
Johnson Controls Unitary Products
5005 York Drive
Norman, OK 73069
264975-BIM-B-1208
Supersedes: 264975-BIM-A-0806
Download PDF