Craftsman | 315.277012 | Owner`s manual | Craftsman 315.277012 Owner`s manual

Owner's Manual
114SHEET PROFESSIONAL
Double Insulated
SANDER
Model No.
315.277012
IS_i_ tl_lL_
r_nual
for future reference
_,
•
•
•
•
•
CAUTION:
Read and
follow all Safety Rules and
Operating Instructions before
first use of this product.
Customer
Help Line:
1-800-932-3188
Sears Roebuck and Co., Hoffman Estates,
IL 60179
Visit the Craftsman web page: www.sears.com/craftsman
972000-858
7-01
USA
Safety
Features
Operation
Maintenance
Parts List
®
•
Table Of Contents ..........................................................................................................................................
2
•
Warranty .........................................................................................................................................................
2
•
Introduction .....................................................................................................................................................
2
•
Rules for Safe Operation .............................................................................................................................
3-4
•
Product Specifications ....................................................................................................................................
5
•
Unpacking .......................................................................................................................................................
5
•
Accessories ....................................................................................................................................................
5
•
Features .........................................................................................................................................................
6
•
Operation .....................................................................................................................................................
•
Maintenance .................................................................................................................................................
10
•
Exploded View and Repair Parts List ......................................................................................................
12-13
•
Parts Ordering / Service ...............................................................................................................................
FULL ONE YEAR WARRANTY
ON CRAFTSMAN
PROFESSIONAL
6-9
14
SANDER
If this rRAFTSHRN Professional Sander fails due to a defect in material or workmanship within one year from
the date of purchase, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE
STORE IN THE UNITED STATES.
BY SIMPLY RETURNING
THE TOOL TO THE NEAREST
SEARS
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck
and Co., Dept. 817WA, Hoffman Estates,
IL 60179
Your sander has many features for making sanding
operations more pleasant and enjoyable. Safety,
performance and dependability have been given top
priority in the design of this sander making it easy to
maintain and operate.
_IL CAUTION: Carefully read through this entire
owner's manual before using your new sander.
Pay close attention to the Rules for Safe
Operation, Warnings and Cautions. If you use
your sander propedy and only for what it is
intended, you will enjoy years of safe, reliable
service.
_.
safety precautions.
Look for this symbol to point out important
Your safety is involved.
It means attention!!!
_1, WARNING:
The operation of any sander can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and a full face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses
with side shields, available at Sears Retail Stores. Always wear eye protection which is
marked to comply with ANSI Z87.1.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and
the explanations with them, deserve your careful attention and understanding. The safety warnings do
not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for
proper accident prevention measures.
SYMBOL
,&
MEANING
SAFETY
ALERT
SYMBOL:
Indicates danger, warning, or caution. May be used in conjunction with other symbols or
pictographs.
A
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
A
WARNING:
Failure to obey a safety waming can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
A
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock
and personal injury.
NOTE:
Advises you of information or instructions vital to the operation or maintenance
of the equipment.
DOUBLE INSULATION
IMPORTANT
Double insulation is a concept in safety, in electric
power tools, which eliminates the need for the usual
three-wire grounded power cord. All exposed metal
parts are isolated from internal metal motor
components with protecting insulation. Double
insulated tools do not need to be grounded.
Servicing of a tool with double insulation requires
extreme care and knowledge of the system and
should be performed only by a qualified service
technician. For service we suggest you return the tool
to your nearest Sears Store for repair. Always use
original factory replacement parts when servicing.
_i
WARNING:
Do not attempt to operate this
tool until you have read thoroughly
and
understand completely
all instructions, safety
rules, etc. contained in this manual. Failure
to comply can result in accidents involving
fire, electric shock, or serious personal
injury. Save owner's manual and review
frequently for continuing
safe operation, and
instructing others who may use this tool.
•
AVOID DANGEROUS
Do
not use power tools in damp or wet locations or
expose to rain. Keep work area well lit.
•
KEEP CHILDREN
AND VISITORS AWAY. All
visitors should wear safety glasses and be kept a
safe distance from work area. Do not let visitors
contact tool or extension cord.
•
STORE IDLE TOOLS. When not in use, tools
should be stored in a dry and high or locked-up
place - out of the reach of children.
KNOW YOUR POWER TOOL. Read owner's
•
manual carefully. Learn its applications and
limitations as well as the specific potential hazards
related to this tool.
DO NOT FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
•
USE RIGHT TOOL. Don't force small tool or
READ ALL INSTRUCTIONS
•
ENVIRONMENT.
•
GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH
GROUNDED SURFACES. For example; pipes,
radiators, ranges, refrigerator enclosures.
•
KEEP GUARDS IN PLACE AND IN WORKING
ORDER.
•
KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
attachment to do the job of a heavy duty tool.
Do not use tool for purpose not intended-for
example-don't use a circular saw for cutting tree
limbs or logs.
•
WEAR PROPER APPAREL. Do not wear loose
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury. Rubber
gloves and nonskid footwear are recommended
when working outdoors. Wear protective hair
RULES FOR SAFE OPERATION (Continued)
FOR WET SANDING OR LIQUID POLISHING.
Failure to comply can result in electrical shock
causing serious injury or worse.
covering to contain long hair and keep it from being
drawn into nearby air vents.
•
ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses; they
are not safety glasses.
PROTECT YOUR LUNGS. Wear a face or dust
•
•
KEEP HANDS AWAY FROM SANDING AREA.
•
NEVER USE IN AN EXPLOSIVE
ATMOSPHERE. Normal sparking of the motor
could ignite fumes.
•
INSPECT TOOL CORDS PERIODICALLY and if
damaged, have repaired by authorized service
facility. Stay constantly aware of cord location.
•
INSPECT EXTENSION
mask if the operation is dusty.
•
PROTECT YOUR HEARING. Wear hearing
protection during extended periods of operation.
•
DO NOT ABUSE CORD. Never carry tool by cord
or yank it to disconnect from receptacle. Keep cord
from heat, oil, and sharp edges.
•
•
•
PERIODICALLY
•
SECURE WORK. Use clamps or a vise to hold
work. It is safer than using your hand and it frees
both hands to operate tool.
•
•
REMOVE ADJUSTING
STAY ALERT AND EXERCISE CONTROL.
Watch
what you are doing and use common sense. Do
not operate tool when you are tired. Do not rush.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, tools
should be disconnected from power supply.
DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products, or any strong
solvents to clean your tool.
DO NOT OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support. Secure tools when working at
elevated positions.
•
KEEP HANDLES
CORDS
and replace if damaged.
•
CHECK DAMAGED
PARTS. Before further use of
the tool, a guard or other part that is damaged
should be carefully checked to determine that it wiFI
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any
other conditions that may affect its operation. A
guard or other part that is damaged should be
properly repaired or replaced by an authorized
service center.
KEYS AND WRENCHES.
Form habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
•
•
AVOID ACCIDENTAL STARTING. Do not carry
plugged-in tool with finger on switch. Be sure
switch is off when plugging in.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
•
•
MAKE SURE YOUR EXTENSION
INSPECT FOR and remove all nails from lumber
before sanding.
•
DO NOT operate this tool while under the influence
of drugs, alcohol, or any medication.
•
POLARIZED
CORD IS IN
GOOD CONDITION. When using an extension
cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord
will cause a drop in line voltage resulting in loss of
power and overheating. A wire gage size (A.W.G.)
of at least 16 is recommended for an extension
cord 100 feet or less in length. A cord exceeding
100 feet is not recommended. If in doubt, use the
next heavier gage. The smaller the gage number,
the heavier the cord.
•
OUTDOOR USE EXTENSION
shock, this tool has a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
CORDS. When tool
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
is used outdoors, use only extension cords suitable
for use outdoors. Outdoor approved cords are
marked with the suffix W-A, for
example - SJTW-A or SJOW-A.
•
PLUGS. To reduce the risk of electric
SAVE THESE INSTRUCTIONS.
Refer to them
frequently and use them to instruct others who may
use this tool. If you loan someone this tool, loan
them these instructions a_so.
NEVER USE THIS OR ANY POWER SANDER
SAVE THESE INSTRUCTIONS
4
_ILWARNING:
Some dust created by power sanding, sawing, grinding, drifting, and other construction
activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based
• crystalline
paints,
silica from bricks and cement and other masonry products,
• arsenic and chromium
from chemically-treated
and
lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment,
such as those dust masks that are specially designed to filter out microscopic particles.
Size of Paper
1/4 sheet
No Load Speed
14,000 opm
Rating
2.0 Ampe_s
Orbital Motion
Paper Type
Your sander has been shipped completely assembled
except for the dust bag. Inspect it carefully to make
sure no breakage or damage has occurred during
shipping. If any parts are damaged or missing, contact
your nearest Sears Retail Store to obtain replacement
parts before attempting to operate sander• The dust
bag, sandpaper, paper punch, and this owner's
manual are also included in the box.
_ll
The following recommended
120 Volts, 60 Hz, AC only
Input
Non-Adhesive Sandpaper
Adhesive Sandpaper
WARNING:
If any parts are missing, do not
operate this tool until the missing parts are
replaced. Failure to do so could result in possible
serious personal injury.
accessories are currently available at Sears Retail Stores•
ALUMINUM OXIDE SHEETS WITH PAPER BACKING (1/4 SHEET)
Item No. 9-28275 -- X-Fine
Item No. -9-28276 -- Fine
Item No. -9-28277 -- Medium
Item No. _9-28278 -- Coarse
PRESSURE-SENSITIVE
ADHESIVE, PAPER BACKED SHEETS (1/4 SHEET)
Item No. -9-28280 -- X-Fine
Item No. 9-28281 -- Fine
Item No. -9-28282 -- Medium
Item No. 9-28283 -- Coarse
THE FOLLOWING
STANDARD
NON-LOADING
4-1/2 X 11 in. SANDING SHEETS CAN BE CUT TO FIT YOUR SANDER,
ALUMINUM
OXIDE SANDING SHEETS
Item No. _9-28250 -- X-Fine
Item No. 9-28251 -- Fine
Item No. -9-28252 -- Medium
Item No. -9-28253-- Coarse
,_
WARNING:
The use of attachments
or accessories not listed might be hazardous.
5
KNOW YOUR
See Figure 1.
ELECTRICAL CONNECTION
SANDER
Before attempting to use your sander, familiarize
yourself with all operating features and safety
requirements.
Your sander has a comfortable palm grip handle that
provides maximum one-hand contro_and comfort, plus
it reduces operator fatigue during continuous sanding
operations; it has quick action paper clamps; it is
suitable for sanding with coarse, medium, and fine grit
sandpaper; and has a built-in dust collection that
collects dust through punched holes in the sandpaper
and cushion.
Your sander has a precision built electric motor. It
should be connected to a power supply that is 120
volts, 60 Hz, AC only (normal household current).
Do not operate this tool on direct current (DC), A
substantial voltage drop will cause a loss of power and
the motor will overheat. Efyour tool does not operate
when plugged into an outlet, double-check the power
supply.
_,
SWITCH
This tool has a simple switch control. To turn your
sander ON, depress the switch button as shown in
figure 1. Depress the switch button in the opposite
direction to turn your sander OFF.
WARNING:
Do not allow familiarity with your
sander to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
severe injury.
APPLICATIONS
(Use only for the purposes listed below)
•
Sanding on wood surfaces.
•
Removing rust from and sanding steel surfaces.
SWITCH
ON
OFF
PAPERCLAMP
DUST
BAG
CUSHION
PLATEN
LEVER
PAPERPUNCH
_,
TAB
Fig 1
WARNING:
Your sander should never be connected to power supply when you are assembling parts,
making adjustments, assembling or replacing sandpaper, cleaning, or when not in use. Disconnecting your
sander will prevent accidental starting that could cause serious personal injury.
6
INSTALLING
SANDPAPER
INSTALLING
See Figures 2 and 3.
See Figure 2.
The cushion on your sander gives you the option of
using either non-adhesive sandpaper that clamps to
the platen; or adhesive backed sandpaper with
pressure sensitive adhesive backing that sticks to the
cushion.
•
INSTALLING
•
NON-ADHESIVE
SANDPAPER
,_
_,
•
WARNING:
Failure to unplug your sander could
result in accidental starting causing possible
serious personal injury.
NON-ADHESIVE
SANDPAPER
WARNING:
Failure to unplug your sander could
result in accidental starting causing possible
serious personal injury.
If replacing sandpaper, remove old sandpaper by
peeling it off cushion, if removing regular sandpaper, release paper clamp by lifting up on lever
and disengaging it from the tab on the platen.
Remove non-adhesive sandpaper, then lift up on
paper clamp lever and lock it into place.
Inspect sandpaper before installing. Do not use if
broken or defective.
Unplug your sander.
•
Carefully peel adhesive
sheet sandpaper.
•
Position sandpaper, making sure front edge of
sandpaper is aligned with front edge of the
cushion, then carefully press sticky side of
sandpaper on cushion. Note: Sandpaper must
be aligned with the front edge of the cushion for
proper functioning of the flush sanding feature.
See Figure 2.
PUNCH
See Figure 3.
PAPERCLAMP
PAPERCLAMP
IN UNLOCKED
POSITION
backing from new 1/4
Note: The cushion on your sander is approximately 1/4
in. smaller than precut adhesive backed sanding sheets.
If desired you may want to trim off the overhang of
sandpaper on the back side of cushion. The cushion has
been made smaller so that multiple sheets of nonadhesive sandpaper can be installed.
PAPER
CUSHION
SANDPAPER
Unplug your sander.
See Figure 2.
•
ADHESIVE
TAB
A paper punch template has been supplied with your
sander. It should be used for aligning and punching
holes in the sandpaper for alignment with the holes in
the cushion.
Punching the holes properly is a necessary step in
order for the dustless feature of your sander to
function properly.
ADHESIVE
Fig. 2
•
If replacing sandpaper, remove old sandpaper. To
remove paper, release paper clamp by lifting up on
lever and disengaging it from the tab on the platen.
•
Insert end of new 1/4 sheet sandpaper
approximately (1/2 inch) under the paper clamp.
•
Lift up on lever and lock into place. Apply downward pressure to conform sandpaper to platen.
•
Wrap sandpaper around cushion. Lift lever on
opposite end of sander and insert loose end of
sandpaper under the paper clamp. Fit sandpaper
against cushion as tight as possible.
•
Lift up on lever and lock into place.
PAPERPUNCH
ORIENTPAPER
PUNCHAS SHOWN
Fig. 3
_,
WARNING:
Always wear safety goggles or
safety glasses with side shields when operating
your sander. Failure to do so could result in
foreign objects being thrown into your eyes,
resulting in possible serious injury, tf the sanding
operation is dusty, also wear a face or dust
mask.
SANDPAPER
SELECTION
Selecting the correct size grit and type sandpaper is
an extremely important step in achieving a high
quality sanded finish. Aluminum oxide, silicon carbide,
and other synthetic abrasives are best for power
sanding. Natural abrasives, such as flint and garnet
are too soft for economical use in power sanding.
In general, coarse grit will remove the most material
and finer grit will produce the best finish in atl sanding
operations. The condition of the surface to be sanded
will determine which grit will do the job. If the surface
is rough, start with a coarse grit and sand until the
surface is uniform. Medium grit may then be used to
remove scratches left by the coarser grit and finer grit
used for finishing of the surface. Always continue
sanding with each grit until surface is uniform.
Note: Do not use sander without sandpaper. Doing
so will damage the cushion.
PREPARING FOR OPERATION
,_
CAUTION:
Be careful not to let your hand cover
the air vents.
SANDING
Clamp or otherwise secure the work to prevent it from
moving under your sander.
_
Fig. 4
Do not force, The weight of the unit supplies adequate pressure, so let the sandpaper and sander do
the work. Applying additional pressure only slows the
motor, rapidly wears sandpaper and greatly reduces
sander speed. Excessive pressure will overload the
motor causing possible damage from motor overheating and can result in inferior work. Any finish or resin
on wood may soften from the frictional heat. Do not
allow sanding on one spot too long as the sander's
rapid action may remove too much matedal, making
the surface uneven.
Flush sanding can be performed with your sander.
See Figure 5. The front edge of your sander allows
flush sanding in corners. Always remove sander from
workpiece before turning your sander off.
WARNING:
Unsecured work could be thrown
towards the operator causing injury.
Hold your sander in front and away from you, keeping
it clear of the workpiece. Start your sander by pressing the switch button to on position and letting the
motor build to its maximum speed. Gradually lower
your sander on the work with a slight forward movement. See Figure 4. Move if slowly using forward and
backward strokes.
_1= WARNING:
Do not wear loose clothing or
jewelry when operating sander. They could get
caught in moving parts causing serious injury.
Keep head away from sander and sanding area.
Hair could be drawn into sander causing serious
injury.
Fig. 5
ORBITAL MOTION
Orbital motion is ideal for fast cutting action when
removing old finishes, smoothing rough wood, cutting
stock down to required dimensions, or for finishing
surfaces to be painted. As shown in figure 6, the
sandpaper moves in tiny circles at a very high speed,
allowing the sander to move easily.
DUST BAG
TO REMOVE
DUSTBAG
Fig. 6
TO EMPTY
•
DUST
•
Slide dust bag retainer from sander as shown by
the arrow in figure 7. Note: Grooves on dust bag
retainer align with grooves on your sander.
•
Empty dust bag.
TO INSTALL
DUSTLESS
SANDING
The dust bag located on the rear of your sander
provides a dust collection system for your sander.
Sanding dust is drawn up through the holes of the
cushion and collects in the dust bag during sanding
operation. For more efficient operation, empty dust
bag when half full.
DUST
BAG
See Figure 8.
•
Unplug your sander.
,_,
WARNING:
Failure to unplug your sander could
result in accidental starting causing possible
serious personal injury.
BAG
DUSTBAG
\
Unplug your sander.
_.
WARNING:
Failure to unplug your sander could
result in accidental starting causing possible
serious personal injury.
•
Unzip dust bag.
•
Shake dust bag to empty.
•
Zip dust bag up after emptying.
TO REMOVE DUST BAG FOR EMPTYING OR
CLEANING
See Figure7.
• Unplug your sander.
,_
Fig. 7
DUSTBAG
RETAINERGROOVES
GROOVES
ON SANDER
WARNING:
Failure to unplug your sander could
result in accidental starting causing possible
serious personal injury.
9
Fig. 8
•
Realign grooves on dust bag retainer with
grooves on your sander.
•
Slide dust bag assembly
the arrow in figure 8.
into place as shown by
_i,
WARNING:
When servicing use only identical
Craftsman replacement parts. Use of any other
parts may create a hazard or cause product
damage.
GENERAL
Only the parts shown on parts list, page 13, are
intended to be repaired or replaced by the customer.
All other parts represent an important part of the
double insulation system and should be serviced only
by a qualified Sears service technician.
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from various
types of commercial solvents and may be damaged
by their use. Use clean cloths to remove dirt, carbon
dust, etc.
EXTENSION CORDS
The use of any extension cord will cause some loss of
power. To keep the loss to a minimum and to prevent
tool from overheating, use an extension cord that is
heavy enough to carry the current the tool will draw.
A wire gage size (A.W.G.) of at least 16 is recommended for an extension cord 100 feet or less in
length. When working outdoors, use an extension
cord that is suitable for outdoor use. The cord's jacket
will be marked WA.
A
CAUTION:
Keep extension cords away from the
sanding area and position the cord so that it will
not get caught on lumber, tools, etc., during
sanding.
_1_ WARNING:
Check extension cords before each
use. If damaged replace immediately. Never use
tool with a damaged cord since touching the
damaged area could cause electrical shock
resulting in serious injury.
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc. come in contact with plastic parts. They
contain chemicals that can damage, weaken, or
destroy plastic.
Extension cords suitable for use with your sander are
available at your nearest Sears Retail Store.
It has been found that electric tools are subject to
accelerated wear and possible premature failure when
they are used on fiberglass boats, sports cars,
wallboard, spackling compounds, or plaster. The
chips and grindings from these materials are highly
abrasive to electric tool parts such as bearings,
brushes, commutators, etc. Consequently, it is not
recommended that this tool be used for extended
work on any fiberglass material, wallboard, spackling
compounds, or plaster. During any use on these
materials it is extremely important that the tool is
cleaned frequently by blowing with an air jet.
_
WARNING:
Always wear safety goggles or
safety glasses with side shields during power tool
operation or when blowing dust. If operation is
dusty, also wear a dust mask.
LUBRICATION
All of the bearings in this tool are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore,
no further lubrication is required.
t0
11
CRAFTSMAN
SANDER - MODEL NO. 315.277012
SEE NOTE "A" PAGE 13
5
4
15_
I
2
!
I
\
I
I
14
12
CRAFTSMAN
SANDER - MODEL NO. 315.277012
L
The model number will be found on a plate attached to the motor housing. Always mention the model
number in all correspondence regarding your SANDER or when ordering repair parts.
SEE BACK
PAGE
FOR PARTS
ORDERING
INSTRUCTIONS
PARTS LIST
Key
No.
Part
Number
Description
1
031500-300
Retaining Plate ........................................................
2
968700-004
Screw (#6-19 x 5/16 in. Pan Hd.) ............................
2
3
968700-007
Screw (#6-19 x 1/2 in. Pan Hd.) ..............................
2
4
662316-001
Fan Baffle ................................................................
1
5
982598-001
Data Plate ................................................................
1
6
662514-001
Dust Bag Assembly
1
7
979853-001
Logo Plate ................................................................
8
***
Quan.
.................................................
2
1
Sandpaper
9
662318-001
Wire Clamp ..............................................................
2
10
623019-004
Rubber Plug .............................................................
1
11
662315-003
Platen .......................................................................
1
12
662317-003
Cushion ....................................................................
1
13
617966-030
Screw (#8-10 x 5/8 in. Pan Hd.) ..............................
4
14
662447-001
Paper Punch ............................................................
1
15
662870-001
Dust Shield ..............................................................
1
972000-858
Owner's Manual
NOTE: "A"- The assembly shown represents an important part of the Double Insulated System.
To avoid the possibility of alteration or damage to the system, service should be
performed by your nearest Sears Repair Center. Contact your nearest Sears Retail
Store for Service Center information.
* Standard Hardware Item - May Be Purchased Locally
*** Complete Assortment Available At Your Nearest Sears Retail Store
13
I
Get it fixed, at your home or ours!
For repair of major brand appliances in your own home...
no matter who made it, no matter who sold it!
1-800-4-MY-HOM
EsMAnyt,me, day
or n,ght
(1-800-469-4663)
www.sears.com
To bring in products such as vacuums, lawn equipment and electronics
for repair, call for the location of your nearest Seers Parts & Repair Center.
1-800-488-1222
Anyt,me, day or n,ght
www,sears.com
For the replacement
parts, accessories
that you need to do-it-yourself,
1-800-366-PART
and owner's
call Sears
manuals
PartsDirect
sM!
6 a m - 11 p m CST,
(1-800-366-7278)
7 days a week
www.sears.com/partsdirect
To purchase
or inquire
about a Sears Service
Agreement:
1-800-827-6655
7am
-5pm.
CST. Mon -Sat
Para ped_r servlclO de reparaclon a domlclho,
y para ordenar p_ezas con entrega a dom_c_ho
1-888-SU-HOGAR
sM
Au Canada pour service en fran£ats
1-877-LE-FOYER
sM
(1-877 -533-6937)
(1-888-784-6427)
® Registered
© Sears
Roebuck
and CO
® Marca
Trademark
Reo=strada
/ P_ Trademark
I vM Marca
of _ars
de F_!lbnca de Sears
Roebuck
Roebuck
and CO
and Co
Download PDF