Carrier | TST-EEPD06121SCS01 | DIGITAL THERMOSTAT

PROGRAMMABLE
DIGITAL THERMOSTAT
Error Codes
Programming Thermostat Schedules
TST-EEPC06111SCS00 / TST-EEPC06121SCS00:
Before programming the thermostat, plan the thermostat daily schedule. The
E1 — If the thermostat cannot properly read room temperature, and it
schedule is divided into 7 days (Monday through Sunday). Each day has 4
time periods (1,2, 3, 4). Each time period has a start time, heating
needs to be adjusted, E1 will be displayed.
TST-EEPC06111SCS00 / TST-EEPD06111SCS01
set point, and cooling set pointFill in Table 1 as an aid to programming
TST-EEPD06111SCS01 / TST-EEPD06121SCS01:
the daily schedules.
E2 — If the thermostat cannot properly read outdoor temperature, and it
NOTE: TST-EEPC06111SCS00 / TST-EEPC06121SCS00has single
needs to be adjusted, E2 will be displayed.
temperature set point.
Set Thermostat Configuration
To program the daily schedules,perform the following procedure:
Configuration options are intended to be selected at installation and
1. Enter programming mode by hold the clock button down for 5 seconds.
normally should not be modified by the home owner. These options are
“Wen” and ”--:--” will be displayed. Use “5” and “6” buttons to select the day
not discussed in the Homeowner’s Guide and therefore must be made
of the schedule. Press The clock button TIME annunciator will flash.
as part of the installation. A special procedure allows entry in to the
NOTE: If a programming button is not pushed for 90 seconds, the
configuration mode. The thermostat will automatically exit this if no
thermostat will exit programming mode.
button is pressed for 90seconds.
2. Press the “5” and “6” buttons to set the start time for the schedule day
An explanation for each of these and how to enter the configuration
TST-EEPC06121SCS00 / TST-EEPD06121SCS01
-7 Day Programmable
-Cool、Heat and Ventilation
and period shown.
3. Press the clock button once, The heating set point and the heat
mode follows.
To enter the configuration mode:
annunciator will be displayed. Press the “5” and “6” buttons to set heating
To enter the configuration mode, hold the fan button down for
set point.
approximately 15 seconds. After 15 the second periof,Option”01” will
4. Press the clock button once, The cooling set point and the cool
-Large, Easy To Read Display
appear in the display.
annunciator will be displayed. Press the “5” and “6” buttons to set cooling
-Blue Backlight
OPTION 01 –LOW TEMPERATURE PROTECTION (FROST
set point.
PROTECTION)
5. Press the clock button to advance to the next time period.
-Fahrenheit or Centigrade
Heat mode
Cool mode
Shows room temperature,
Ventilation mode
Room temperature
Set desired temperature
In the low temperature protection mode, When the thermostat is off , and
6. Perform Steps 2 through 5 until the times and temperature set points have
the room temperature is lower than 5℃, it will be turned on automatically
been entered for the entire day. Press the clock button and display”copy”,use
desired temperature, and
and in heating mode; When the room temperature is higher than 7℃, it
“5” and “6” buttons to select the day for copy, press the clock button to
other feature information
will be turned off automatically.
confirm.
as required.
TO ADJUST:
7. Repeat Steps 2 through 6 to program the remaining schedule days.
Current Time
Enter configuration mode (if not already there).
Table 1 Daily Schedule Planner
Use “5” and “6” buttons to display Option 01.The SET icon should be
Change mode
SET
SCHEDULE
off.
Fan indicator
Press” M ” button once. The SET icon will be come on. The display now
shows Option 01 setting.
Use “5” and “6” buttons to move between the available Option 01
choices of 00(disable) or 01(enable). Factory default is 00.
Power button
Mode button
Press” M ” button again to return to Option 01. The SET icon will now be
off.
Fan button Down button Up button
Use “5” and “6” buttons to select another Option, or press”
Clock button
“button
to exit configuration mode.
Specification
DAY OF
1
2
3
4
WEEK
Tim/Heat/Cool
Tim/Heat/Cool
Tim/Heat/Cool
Tim/Heat/Cool
Monday
/
/
/
/
/
/
/
/
/
/
/
Tuesday
/
/
/
/
/
/
/
/
/
/
/
/
Wednesday
/
/
/
/
/
/
/
/
/
/
/
/
Thursday
/
/
/
/
/
/
/
/
/
/
/
/
Friday
/
/
/
/
/
/
/
/
/
/
/
/
Saturday
/
/
/
/
/
/
/
/
/
/
/
/
Sunday
/
/
/
/
/
/
/
/
/
/
/
/
OPTION 02 –FAHRENHEIT/CELSIUS SELECTION
Set-Point Range: 5℃-35℃(41℉-95℉)
This option selects Fahrenheit or Celsius operation.
Wire Diagram
Operating difference: ± 1℃
TO ADJUST:
Switch current rating: < 2A
Enter configuration mode (if not already there).
Use “5” and “6” buttons to display Option 02.The SET icon should be
Sensing element : NTC
TST-EEPC06111SCS00/ TST-EEPC06121SCS00:
off.
Display: LCD
Press” M ”button once. The SET icon will be come on. The display now
Power supply:
shows Option 02 setting.
L(R)
L(R)
Use “5” and “6” buttons to move between the available Option 02
TST-EEPC06111SCS00: AC85V~220V 50Hz/60Hz
choices of F (Fahrenheit) or C (Celsius). Factory default is C.
Val
Val
TST-EEPD06111SCS01: AC85V~220V 50Hz/60Hz
Press” M ”button again to return to Option 02. The SET icon will now be
Low
Low
TST-EEPC06121SCS00: AC24V ±10% 50Hz/60Hz
off.
Med
Med
to exit configuration mode.
Hi
Hi
OPTION 3-ROOM TEMPERATURE OFFSET
N(C)
N(C)
Use “5” and “6” buttons to select another Option, or press “
TST-EFPD06121SCS01: AC24V ±10% 50Hz/60Hz
Dimensions: 86 × 86 × 29.5 mm(W×H×D)
“button
Housing: ABS Flame Retardant
This option allows calibration (or deliberate miscalibration) of room
Basic Operation
temperature sensor. There are various reasons why the home owners
Power ON/OFF
want to adjust the displayed temperature. The selected number is the
To turn the thermostat on, press “
”. Mode symbol (
,
or
),
“RT”, and room temperature will be displayed.
To turn the thermostat off, press “
LCD and no any output.
which will be displayed and acted upon as if it were 72. The effect is that
” is displayed, it will be confirmed
” is displayed, it will be confirmed
Ventilation Setting:Press “M”, until the “
” is displayed, it will be
confirmed automatically after 6 seconds.
L(R)
Val
Low
Low
plus or minus 1F, so this adjustment will provide the best accuracy when
Med
Med
set to 0.
Hi
Hi
N(C)
N(C)
TO ADJUST:
Enter configuration mode(if not already there).
Fan Setting:
Use “5” and “6” buttons to display Option 03.The SET icon should be
Fan speed select: press the fan button to select “
(Auto)”. In mode“
L(R)
Val
a positive number selection will make the room temperature lower and
vice versa. This thermostat is factory calibrated within an accuracy of
automatically after 6 seconds.
(Low)、
display and control action.For example, if 2 is selected, 72F actual will
read 74F. If setpoint is 72, the room will control to an actual value of 70
automatically after 6 seconds.
Heat Setting:Press “M”, until the “
TST-EEPD06111SCS01/ TST-EEPD06121SCS01:
temperature. The number can range between -5 and +5. Factory default
is 0. This adjusted value will be used as actual temperature for both
” again. There is no any display on
Select Mode:
Cool Setting:Press “M”, until the “
number of degrees, plus or minus, which will be added to the actual
(Hi)、
(Med)、
(Auto)”, the fan-speed changed
automatically. Auto LOW-speed When the difference between
room-temperature and setting-temperature exceed 1℃(2℉), Auto
MED-speed When exceed 2℃(4℉), Auto HI-speed When exceed 3℃(6
℉).
off.
Press” M ”button once. The SET icon will be come on. The display now
S1
OUTDOOR SENSOR
shows Option 03 setting.
S2
CONNECTION
Use “5” and “6” buttons to move between the available Option 01
choices of -5 through +5 in 1 step. Factory default is 0.
Press” M ”button again to return to Option 03. The SET icon will now be
off.
Select Current Stage Temperature
Use “5” and “6” buttons to select another Option, or press “
TST-EEPC06111SCS00 / TST-EEPC06121SCS00:
to exit configuration mode.
Press”5” or ”6” until the desired temperature set point is displayed.
OPTION 04 –SAVE CONFIGURATION DATA
TST-EEPD06111SCS01 / TST-EEPD06121SCS01:
This option can be used to choose Save configuration data
Press ”5” or ”6” until the desired heating or cooling temperature set
point is displayed.
Press the MODE button to select the second temperature setting(either
HEAT or COOL)
Set Current Time
Press the clock button. The hour of the time will flashing. Press the “5”
and “6” buttons until the correct time is shown. Press the clock button
once,the minute of the time will flashing. Press the “5” and “6” buttons
until the correct time is shown. Press the clock button once,the day will
flashing. Press the “5” and “6” buttons to the day.
“button
TO ADJUST:
Enter configuration mode (if required).
Use up and down buttons to display Option 04.The SET icon should be
off.
Press” M ” button once. The SET icon will come on. The display now
shows Option 04 setting.
Use “5” and “6” buttons to move between the available Option 04
choices of 00(disable) or 01(enable). Factory default is 01.
Press ” M” button again to return to Option 04. The SET icon will now be
off.
Use “5” and “6” buttons to select another Option, or press “
to exit configuration mode.
1/2
“button
/
Thermostat
Fan coil
Installation:
Thermostat Location
Thermostat should be mounted:
• Approximately 5 ft (1.5m) from floor.
• Close to or in a frequently used room, preferably on an inside
partitioning wall.
• On a section of wall without pipes or duct work.
1. Cut off the power, the mark of wire should be clear.
2. Take the main control panel
3.Push up by force, open the clip.
apart.
4. As per wiring drawing, connect
5. Fix by the two screws in the
with terminals, fix it by crewdriver.
packing box.
6. Push the downside by force,
lock the up panel, and finish the
installation.
2/2
Download PDF