American DJ | Accu Spot 250 II | Specifications | American DJ Accu Spot 250 II Specifications

American DJ
®
Accu Spot 250™
Table of Contents
User Instructions
Rev. 9/04
American DJ®
4295 Charter Street
Los Angeles CA. 90058
www.americandj.com
Unpacking......................................................................3
Introduction....................................................................3
Customer Support......................................................................3
Safety Precautions......................................................................4
Handling Precautions..................................................................5
Discharge Lamp Warnings..........................................................5
Registration......................................................................6
Features.........................................................................6
Controls and Functions..............................................................7
Set-Up.............................................................................10
System Menu............................................................................13
Editing Program.........................................................................25
Operating Modes.......................................................................28
Fuse and Lamp Replacement...................................................30
DMX Traits.................................................................................32
Gobos..................................................................................33
Gobo Replacement...................................................................35
Cleaning..................................................................36
Trouble Shooting.......................................................................36
Warranty.................................................................37
Specifications....................................................................39
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 2
Accu Spot 250™
General Information
Unpacking: Thank you for purchasing the Accu Spot 250™ by
American DJ®. Every Accu Spot 250™ has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your fixture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without
contacting customer support first.
Introduction: The Accu Spot 250™ is a eight channel, moving head,
intelligent DMX fixture. The fixture can operate in three different operating modes; stand alone, sound-active, or in a Master/Slave configuration. The Accu Spot 250™ comes with several built in programs and
is best used in multiples of four. When used as a stand alone unit or
when used in multiples linked in a master/slave configuration. For best
results use fog or special effects smoke to enhance the beams projections.
During the initial start-up or use of this product a light smoke or
smell may arise from the unit. This is a normal process and is
cause by the heat associated with the lamp.
Customer Support: American DJ® provides a toll free customer
support line, to provide help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:
00 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax:
(323) 582-2610
E-mail:
support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 3
Accu Spot 250™
Safety Precautions
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required voltage for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product outdoors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 38 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a
marked change in performance.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 4
Accu Spot 250™
Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact American DJ®.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
American DJ® will not accept any liability for any resulting damages
caused by the non-observance of this manual or any unauthorized
modification to this unit.
Accu Spot 250™
Discharge Lamp Warning
This fixture is fitted with a discharge lamp which
is highly susceptible to damage if improperly
handled. Never touch the lamp with your bare fingers as the oil from your hands will shorten lamp
life. Also, never move the fixture until the lamps
have had ample time to cool. Remember, lamps
are not covered under warranty conditions.
This unit emits intense UV radiation which is harmful to the eyes and
skin. The intense luminance of the lamp can cause severe damage
to the retina. Never operate this unit without it’s covers, these covers
have been specially designed to shield against UV radiation.
Epileptic Warning: Those suffering from epilepsy should avoid looking
directly into the lamp at all times.
Avoid switching the fixture on and off repeatedly in short intervals as
this will reduce lamp life and intensity.
To achieve the intensity associated with discharge lamps, these lamps
use gas sealed in a high pressure environment to emit a brilliant output.
Due to the high pressure involved with the construction of the lamp,
the lamp may explode during prolonged extensive use. This risk is
increased with age, added care is encouraged when dealing with older
lamps. Extreme caution should be used when operating this or any
fixture fitted with a gas discharge lamp. Never open this unit while in
use.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 5
Accu Spot 250™
General Instructions
To optimize the performance of this product, please read these operating
instructions carefully to familiarize yourself with the basic operations of
this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with
the unit, for future reference.
Accu Spot 250™
Product Registration
The Accu Spot 250™ carries a one year limited warranty. Please fill
out the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper and included in the shipping carton.
If the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our toll free customer support number. All
packages returned to the service department not displaying a R.A.
number on the outside of the package will be returned to the shipper
at the shippers cost.
Accu Spot 250™
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Features
Micro-Stepping Motors for Smooth Color and Gobo Transitions
DMX-512 Protocol Compatible (Uses Eight DMX Channels)
Independent Gobo and Color Wheels
8 Rotating Gobos, 1 Dichroic + Spot - All Replaceable
9 Colors, Plus White - With Rainbow
3 Operating Modes - Master/Slave; Stand Alone; Sound Active
Internal Microphone
ZB-MSD250 Discharge Lamp, 230v/250w
Edit and Save Scenes into the Memory
Manual Focus Lens
Variable Strobe (1-12 fps)
360˚ Pan Movement
265˚ Tilt Movement
Digital Display for Address and Function Setting
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 6
Accu Spot 250™
Controls and Functions
Accu Spot 250™
Controls and Functions
1. Lens Assembly - This high quality lens is a fully focusing. Focus
the lens by manually turning the lens in a clockwise or counter-clockwise direction until the desired effect is achieved.
FRONT
1
2. Digital Display - This display shows the menu and operating functions that you can choose from.
3. Enter Button - This button is used to select and confirm a function when working in the system menu. It is also used to exit certain
menus.
4. Exit/DN Button - This button is used to exit menus and to scroll
backwards through certain menus only.
REAR
2
5. Up Button - This button is used to scroll forward when navigating
through the system menu.
9
6. Carrying Handles - The includes built-in carrying handles. Be sure
to always handle the unit by the built-in handles. Never lift or carrying the unit by head or yoke. Pulling on or transporting the unit by the
moving head may severely damage the unit and will void the unit warranty.
3
4
5
6
7
8
10
7. XLR Output Jack - This jack is used to transmit the incoming
DMX signal to another DMX fixture, or transmit a Master/Slave signal
to the next Accu Spot 250™ in the chain. For best results in DMX or
Master/Slave mode terminate this jack if it is the last unit in the chain.
See “Terminator” on page 11.
8. XLR DMX Input Jack - This jack is used to receive an incoming
DMX signal or Master/Slave signal.
9
6
11
12
9
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 7
9. Cooling Fan - This unit is equipped with three high velocity variable
fans to aid in the cooling process. These fans are designed to vary
their velocity at different operating temperatures, to provide better
cooling when the unit reached higher operating temperatures associated with long usage. Be sure to never obstruct the cooling fans during
normal usage. Also, be sure to keep the vents clean at all times. A
blocked or malfunctioning cooling system may shorten lamp life and
unit reliability.
10. Lamp Assembly and Access Plate - This plate accesses the lamp
socket assembly. The unit includes a spring mounted ZB-MSD250
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 8
Accu Spot 250™
Controls and Functions
230v/250w discharge lamp. Be sure to only replace with same type
lamp. After replacing a lamp be sure the lamp is centered in the reflector. See page 32 for details on installing and optimizing replacement
lamps. Never operate this unit with the lamp exposed, this lamp emits
strong UV radiation.
11. Fuse Holder - This housing stores a 10 amp (5 amp 220v) GMA
protective fuse. Never defeat the fuse, the fuse is designed to protect the electronics in the event of severe power fluctuations. Always
be sure to replace the fuse with an exact match as the one being
replaced, unless otherwise told to do so by an authorized American
DJ® service technician.
12. Power Cord Inlet - This unit is equipped with a removable I.E.C.
power cord. Be sure to only use the power cord included with the unit,
this cord is designed to match the electrical requirements of the unit.
Other cords may cause the unit to overheat or malfunction. Voltage
may vary from venue to venue, when connecting this unit to a power
supply be sure to connect to a matching power outlet. Never use
this fixture if the ground prong has been removed or broken off. The
ground prong is designed to reduce the risk of fire or electrical shock
in the event the unit suffers from an internal short.
Accu Spot 250™
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your American DJ®
Accu Spot 250.™ The American DJ® Accu Spot 250™ is available in
a 120v and 220v version. Because line voltage may vary from venue
to venue, you should be sure your unit voltage matches the wall outlet
voltage before attempting to operate you fixture. Also be sure to only
use the included I.E.C. power cable supplied with the unit, this cable
matches the voltage and current requirements of the unit.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX
and Master/Slave Operation): The Accu Spot
250™ can be controlled via DMX-512 protocol.
The Accu Spot 250™ is a eight channel DMX unit.
The DMX address is set electronically using the
controls on the side panel of the unit. Your unit and
your DMX controller require a standard 3-pin XLR
connector for data input and data output (Figure
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 9
Set Up
Figure 1
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 10
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
REMOTE
CONTROL
INPUT
SOUND
Accu Spot 250™
INPUT
OUTPUT
Set Up
1). If you are making your own cables, be sure to use standard two
conductor shielded cable (This cable may be purchased at almost all
professional sound and lighting stores). Your cables should be made
with a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.
POWER
POWER
Notice: Be sure to follow
figures two and three when making your own
DMX512
DMX+,DMX-,COMMON
cables. Do not use
the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
DMX512 OUT
3-PIN XLR
DMX +
1
3
DMX -
2
1
1
DMX512 IN
3-PIN XLR
3
2
3
2
Figure 2
SOUND
REMOTE
CONTROL
INPUT
XLR Female Socket
XLR Male Socket
REMOTE
CONTROL
INPUT
SOUND
2 Cold
2 Cold
INPUT
OUTPUT
1 Ground
3 Hot
Set Up
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
POWER
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Pin 2
Pin 2
Pin 3
Pin 3
(- signal)
Termination reducesData
signalCompliment
errors and
avoids signal transmission problems
and interference. It is always
advisable
Data True (+ signal)
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the lastNot
fixture.
Used
Pin 4 - Do Not Use
Pin 5 - Do Not Use
XLR Pin Configuration
Pin 1 = Ground
REMOTE
CONTROL
SOUND
OUTPUT
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
Not Used
1 Ground
INPUT
Accu Spot 250™
INPUT
OUTPUT
INPUT
Pin 2
= Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
Figure 3
Special Note: Line Termination. When longer runs of cable are
POWER
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
1
3
2
DMX512 IN
3-PIN XLR
1
3
2
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 11
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 12
Accu Spot 250™
System Menu
ADDR
VALU
RDIS
MODE
VALU
DISP
DELA
MAIN MENU
LAMP
OPEN
ON
OFF
ONLI
ON
OFF
SET
LADJ
ON
OFF
TEST
T-01
T-08
CLLT
ON
OFF
ADJU
TINE
ON
OFF
AUTO
ALON
MAST
SOUN
ALON
MAST
System Menu
ADDRESS MENU A001
A511
SLAV (Slave) - Designates a unit to be a slave unit in master/
slave mode.
VALU (Value) - This is for setting the DMX address of the unit.
D-01
D-08
DISPLAY MENU DISP (Display) - Takes you into the display menu of settings.
RDIS (Reverse Display) - “Flips” the digital display 180º.
VALU (DMX-512 Value) - Display the DMX-512 value of each
channel.
CLDI - Turns digital display off after 2 minutes.
REST
ON
OFF
RPAN
ON
OFF
RTILT
ON
OFF
LODA
ON
OFF
VER
V-2.2
RUN MENU RUN (Run) - Takes you into the run menu to select a mode to run
the unit in.
AUTO (Automatic) - Runs its own internal program.
SOUN (Sound Active) - The unit will run in sound active mode.
ALON (Alone) - Unit runs in stand alone mode, no master/slave.
MAST (Master) - Designates that unit to be master in master/
slave mode.
LAMP MENU DELA (Delay) - Delays lamp turning “On”.
NATI
LATI
CLNT
EDIT
ON
OFF
CLDI
RUN
D-00
D-59
ON
OFF
SLAV
Accu Spot 250™
OPEN (Open) - Switches the lamp “On” or “Off”.
ON
OFF
STEP
S-01
S-48
SCO1
SC48
C-01
C-08
OML1 - External controller will switch lamp “On” and “Off”.
TINE
C-01
C-30
CNIN
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 13
SET MENU REST (Reset) - Resets the unit.
RPAN (Reverse Pan) - Reverses the pan.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 14
Accu Spot 250™
System Menu
Accu Spot 250™
System Menu
RTILT (Reverse Tilt) - Reverses the tilt.
On-Board System Menu. The Accu Spot 250™ comes with an
LODA - Restores factory settings.
easy to navigate system menu. This next section will detail the functions of each command in the system menu.
VER (Version) - Software version 2.2
ADJUST MENU LADJ (Lamp Adjustment) - With this function you can adjust
the lamp via the control board. In this mode, the device will not
react to any control signal.
TEST (Test) - Tests the functions of each channel. There are eight
channels, but only channels 1,2,3,4, and 6 can be tested.
TIME MENU CLLT - Clears the lamp running time.
NAT 1 - Displays the fixture running time.
Enter Button - To access the main menu locate the ENTER button
(3) on the side of the unit. Press this button for 3 seconds to activate
the system menu. Tap the UP button (5) until you reach function you
wish to change. When you reach the function you wish to change tap
the ENTER button. When a function is selected the menu will begin to
flash, use the UP button to change the function. Once your changes
are made tap the ENTER button again to lock the change in the system,
if the ENTER button is not selected within eight seconds the system
will automatically return to menu section. To exit without making any
changes tap the EXIT/DN button (4).
MODE MAIN MENU -
LAT 1 - Displays the lamp running time.
ADDR
CLNT - Clears the fixture running time.
1. Access the main menu.
EDIT MENU STEP (Step) - Steps to be used in Edit Programming. See ediit
program. See page 27.
SCO1 - SC48 (Scene 01 - Scene 48) - These are the scene slots
that you write your programs into. See edit program, page 28.
TIME (Time) - Time for each scene. See page 28.
CNIN - Edit program using a external controller. See page 30.
C-01 - C-30 (Channel 1 - Channel 30) - The channels of each
scene that can be edited. See page 28.
DMX Address Setting via control board -
2. Tap the UP button until “NODE” is displayed, press ENTER.
3. Tap the UP button until “ADDR” will now be displayed. Press
ENTER.
4. Now the display will show “VALU”, press ENTER. Now, “A001”
should be displayed. Adjust the DMX address by pressing the
UP or DOWN buttons.
5. Press ENTER to confirm.
6. Press the EXIT/DN button to return to the main menu.
When the display is on “A001”, you can directly press the UP
or DN buttons to change the DMX start address.
SLAV
Define the unit as a slave, in master/slave mode -
1. Access the main menu.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 15
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 16
Accu Spot 250™
System Menu
Accu Spot 250™
System Menu
2. Tap the UP button until “NODE” is displayed, press ENTER.
2. Tap the UP button until “NODE” is displayed, press ENTER.
3. Tap the UP button until “SLAV” is displayed, press ENTER.
3. Tap the UP button until “DISP” is displayed, press ENTER.
4. Press ENTER, the display will show “ON/OFF”.
4. “VALU” should now be displayed, press ENTER.
5. The display should show “D-00”. Press the UP button in
order to select the desired channel. If you select “D-05” the
display will only show the DMX value of the 5th channel
5. Press the UP button to select “ON” to activate this unit as a
slave, or “OFF” to deactivate this unit.
6. Press ENTER to confirm.
7. Press EXIT/DN to return to the main menu.
RUN
With the function “RUN”, you can run the units internal program. You can set the number of steps under Step.
You can edit the individual scenes under Edit. You can run
the individual scenes either automatically “AUTO”, or soundactive “SOUN”. The selection “ALON” means stand alone and
“MAST” means that the unit is designated as the master in
master/slave mode.
6. Press ENTER to confirm.
7. Press EXIT/DN to return to the main menu.
Now the display will change as per the 5th channel DMX
value.
CLDI
Shuts off digital display after 2 minutes.
1. Access the main menu.
2. Tap the UP button until “NODE” is displayed, press ENTER.
1. Access the main menu.
3. Tap the UP button until “DISP” is displayed, press ENTER.
2. Tap the UP button until “NODE” is displayed, press ENTER.
4. “CLDI” should now be displayed, press ENTER.
3. Tap the UP button until “RUN” is displayed, press ENTER.
5. The display will show “ON/OFF”. Press the UP button to
select “ON” to activate this function, or “OFF” to deactivate this
function.
4. “AUTO” is displayed. If you press the UP button it will show
“SOUN”. Select which one you want to activate, and press
ENTER.
6. Press ENTER to confirm.
5. Press UP, to select “ALON” or “NAST”. Which mean stand
alone, and master/slave mode.
7. Press EXIT/DN to return to the main menu.
6. Select a mode, and press ENTER to confirm.
LAMP MAIN MENU -
7. Press EXIT/DN to return to the main menu.
OPEN With this function you can switch the lamp on or off
via the control board.
DISP
Display the DMX-512 value of each channel -
1. Access the main menu.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 17
1. Access the main menu.
2. Tap the UP button until “LAMP” is displayed, press ENTER.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 18
Accu Spot 250™
System Menu
Accu Spot 250™
System Menu
3. Tap the UP button until “OPEN” is displayed, press ENTER.
SET MAIN MENU -
4. The display will show “ON/OFF”. Press the UP button to
select “ON” to switch on the lamp, or “OFF” to switch off the
lamp.
RDIS - This function will reverse the display 180º.
5. Press ENTER to confirm.
2. Tap the UP button until “RDIS” is displayed.
6. Press EXIT/DN to return to the main menu.
3. Press ENTER, the display will show “ON/OFF”.
ONL I
With this function you can switch the lamp on or off
via an external controller.
4. Press the UP button to select “ON” to activate this function,
or “OFF” to deactivate this function.
1. Access the main menu.
5. Press ENTER to confirm.
2. Tap the UP button until “LAMP” is displayed, press ENTER.
6. Press EXIT/DN to return to the main menu.
3. Tap the UP button until “ONL I” is displayed, press ENTER.
RPAN - The movement of the Pan will be reversed.
4. The display will show “ON/OFF”. Press the UP button to
select “ON” to switch on the lamp, or “OFF” to switch off the
lamp.
1. Access the main menu.
1. Access the main menu.
2. Tap the UP button until “SET” is displayed, press ENTER.
5. Press ENTER to confirm.
3. Tap the UP button until “RPAN” is displayed, press ENTER.
6. Press EXIT/DN to return to the main menu.
4. The display will show “ON/OFF”.
DELA
5. Press the UP button to select “ON” to activate this function,
or “OFF” to deactivate this function.
- With this function you can delay the lamp ignition.
1. Access the main menu.
6. Press ENTER to confirm.
2. Tap the UP button until “LAMP” is displayed, press ENTER.
7. Press EXIT/DN to return to the main menu.
3. Tap the UP button until “DELA” is displayed, press ENTER.
4. The display shows “D-00”. Press the UP button to select the
desired delay between “00” and “59” minutes. For example, if
you select “D-03” the lamp will ignite after 3 minutes.
5. Press ENTER to confirm.
RTILT - The movement of the Tilt will be reversed.
1. Access the main menu.
2. Tap the UP button until “SET” is displayed, press ENTER.
6. Press EXIT/DN to return to the main menu.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 19
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 20
Accu Spot 250™
System Menu
3. Tap the UP button until “RTILT” is displayed, press ENTER.
4. Press ENTER, the display will show “ON/OFF”.
Accu Spot 250™
System Menu
5. Press the UP button to display “ON” to activate this function,
or “OFF” to deactivate this function.
5. Press the UP button to select “ON” to activate this function,
or “OFF” to deactivate this function.
6. Press ENTER to confirm.
6. Press ENTER to confirm.
7. Press EXIT/DN to return to the main menu.
When you exit this function, the unit will begin to reload
data.
REST - When you activate the reset function, the fixture
VER - Use this function to display the Software version of
will begin the reset motion.
the unit.
1. Access the main menu.
1. Access the main menu.
2. Tap the UP button until “SET” is displayed, press ENTER.
2. Tap the UP button until “SET” is displayed, press ENTER.
2. Tap the UP button until “REST” is displayed, press ENTER.
3. Tap the UP button until “VER” is displayed, press ENTER.
3. The display will show “ON/OFF”.
4. The display will show “V-X.X”, “X.X” stands for the version
number, such as the display may show “V-1.0”, “V-2.6” etc.
4. Press the UP button to select “ON” to activate this function,
or “OFF” to deactivate this function.
5. Press ENTER to confirm.
6. Press EXIT/DN to return to the main menu.
LODA - With this function you can restore the factory
settings of the device. All settings will be set back to the
default values. Any edited scenes will be lost. When restoring the factory settings the unit must be set to the address
that the unit was in when you started editing.
7. Press EXIT/DN to return to the main menu.
5. Press ENTER or EXIT/DN to exit.
ADJU MAIN MENU -
TEST - This will test the functions of each channel.
1. Access the main menu.
2. Tap the UP button until “ADJU” is displayed, press ENTER.
3. Tap the UP button until “TEST” is displayed, press ENTER.
2. Tap the UP button until “SET” is displayed, press ENTER.
4. The display will show “TE-X”, “X” stands for the channel
number, if you selected “TE-3”, the unit will test the color channel, change the color one by one and show the rainbow effect
with different speeds.
3. Tap the UP button until “LODA” is displayed, press ENTER.
5. Press ENTER or EXIT/DN to exit.
1. Access the main menu.
4. The display will show “ON/OFF”.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 21
©American
DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 2
Accu Spot 250™
System Menu
LADJ
- With this function you can adjust the lamp via
the control board. The shutter opens and the lamp can be
adjusted. In this mode, the device will not react to any control signal.
1. Access the main menu.
2. Tap the UP button until “ADJU” is displayed, press ENTER.
Accu Spot 250™
System Menu
3. Tap the UP button until “LAT I” is displayed, press ENTER.
4. The display shows “XXXX”, “X” stands for the number of
hours.
5. Press ENTER or EXIT/DN to return to the main menu.
CLNT - With this function you can clear the running time of
3. Tap the UP button until “LADJ” is displayed, press ENTER.
the unit.
4. The display will show “ON/OFF”.
1. Access the main menu.
5. Press the UP button to select “ON” to activate this function,
or “OFF” to deactivate this function.
2. Tap the UP button until “TIME” is displayed, press ENTER.
3. Tap the UP button until “CLNT” is displayed, press ENTER.
6. Press ENTER to confirm.
4. Press ENTER, the display will show “ON/OFF”.
7. Press EXIT/DN to return to the main menu.
5. Press the UP button to select “ON” to activate this function,
or “OFF” to deactivate this function.
TINE MAIN MENU -
6. Press ENTER to confirm.
NAT I - With this function you can display the running time
7. Press EXIT/DN to return to the main menu.
of the unit.
1. Access the main menu.
2. Tap the UP button until “TIME” is displayed, press ENTER.
3. Tap the UP button until “NAT I” is displayed, press ENTER.
4. The display shows “XXXX”, “X” stands for the number of
hours.
5. Press ENTER or EXIT/DN to return to the main menu.
LAT I - With this function you can display the running time
CLLT - With this function you can clear the running time of
the lamp. Note Very Important: Please clear the lamp time
every time you replace the lamp.
1. Access the main menu.
2. Tap the UP button until “TIME” is displayed, press ENTER.
3. Tap the UP button until “CLLT” is displayed, press ENTER.
4. Press ENTER, the display will show “ON/OFF”.
5. Press the UP button to select “ON” to activate this function,
or “OFF” to deactivate this function.
of the lamp.
6. Press ENTER to confirm.
1. Access the main menu.
7. Press EXIT/DN to return to the main menu.
2. Tap the UP button until “TIME” is displayed, press ENTER.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 23
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 24
Accu Spot 250™
Editing Program
Accu Spot 250™
Editing Program
STEP - With this function you can define the number of
6. Adjust the DMX value by pressing the UP button, until you
get the expected effect for this channel.
1. Access the main menu.
7. Press ENTER to enter the editing of the other channels of the
scene.
steps in the Run Program.
2. Tap the UP button until “EDIT” is displayed, press ENTER.
3. Tap the UP button until “STEP” is displayed, press ENTER.
4. The display shows “S-XX”, “X” stands for the total amount
of steps you want to save, so you can call up to 48 scenes in
“Run”. For example, if the “XX” is 05, it means that “Run” will
run the first 5 scenes you saved in “Edit”.
5. Press ENTER to save and exit.
EDIT - This menu item allows you to write a program into the
memory (EEPROM) via the control panel or via the external
controller.
Editing procedure 1: Using the control board only.
1. Access the main menu.
2. Tap the UP button until “EDIT” is displayed. Press ENTER.
3. The display will show “SCXX”, the “X” again stands for the
scene number. For example, “SC01” is displayed, it means you
will be editing scene 1, press ENTER. You can change the
scene number by pressing the UP button.
8. Repeat steps 5-8, until you finish setting all the DMX values
for all the channels of this scene, each scene can have 15
channels maximum.
9. Once all the channels are completed, the display will flash
“TIME”, this stands for the time needed to run this scene.
10. Press ENTER to edit the time needed, the display shows
“T--X”, “X” stands for the time needed to run this scene. For
example, “T--2” means scene 1 needs 2 seconds to run, “T-15”
means scene 1 needs 15 seconds to run.
11. Adjust the time needed by pressing the UP button.
12. Press ENTER to save the settings for the scene you are
editing, the display will change to the next scene automatically.
13. Repeat steps 3-12 to edit other scenes, you can edit and
save 48 scenes maximum.
14. Press EXIT/DN to exit, now you have edited and saved
scenes using the control board. The number of steps can be
defined under “Step” and the scenes can be called up under
“Run”. To run the scenes see page 18.
4. Press ENTER, the display will show “C-X”, the “X” again
stands for the channel number. If “C-01” is displayed, you will
be editing channel 1 of your selected scene, press ENTER. You
can change the scene number by pressing the UP button.
5. The display will show the DMX value for the channel that is
being edited. It will be displayed as “11XX”, it stands for Channel
11 of the editing scene, the DMX value is “XX”.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 25
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 26
Accu Spot 250™
Editing Program
Editing procedure 2: Using an external controller.
1. Access the main menu.
2. Tap the UP button until “EDIT” is displayed. Press ENTER.
3. The display will show “SCXX”, “X” stands for the scene
number to be edited. For example: If “SC01” is displayed, you
will be editing scene 1.
4. Change the scene number by pressing the UP button.
5. Press ENTER, the display will show “C-01”, the “1” stands for
the channel number 1.
6. Press the UP button until “CNIN” is displayed, press ENTER.
7. The display will show “OFF”, press the UP button so that “ON”
is displayed, press ENTER.
8. The display shows “SC02”. You have successfully downloaded the first scene.
9. Adjust the Step-time. needed by pressing the UP button.
10. Call up the second scene in your controller now.
11. Repeat steps 3-6 until all desired scenes are downloaded.
12. Press EXIT/DN to exit. The number of steps can be defined
under “Step” and the scenes can be called up under “Run”.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 27
Accu Spot 250™
Operation
Operating Modes: The Accu Spot 250™ can operate in three
different modes. This next section will detail the differences in
the operating modes.
• Stand alone mode The unit will react to sound, chasing through the built-in programs.
• Master/Slave mode You can daisy chain up to 16 units together to get a synchronized
light show without the need of an external controller. The units will
react to sound chasing through the several built-in programs.
• DMX control mode This function will allow you to control each individual fixtures
traits with a standard DMX-512 controller such as the LSC® Show
Designer.™
Universal DMX Control: This function allows you to use a universal DMX-512 controller such as the American DJ® DMX Operator™ or
LSC® Show Designer™ to control head movement, the color wheel,
gobo wheel, and the shutter (strobe). A DMX controller allows you to
create unique programs tailored to your individual needs.
1. The Accu Spot 250™ uses eight DMX channels. Channel 1 controls pan, channel 2 controls tilt, channel 3 controls color, channel
4 controls gobo wheel, channel 5 controls gobo rotation, channel 6 control the shutter/strobe, channel 7 accesses internal programs, and channel 8 controls the speed of the pan/tilt movement. See page 35 for detailed description of the DMX traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 10-14 as well as the set-up specifications that are
included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 16 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 28
Accu Spot 250™
Operation
Stand-Alone Operation (Sound Active): This mode allows a
single unit or several units linked together, to run to the beat of the
music.
1. Access the main menu.
2. Tap the UP button until “NODE” is displayed, and Press ENTER.
3. Tap the UP button until “RUN” is displayed, and Press ENTER.
4. “AUTO” is displayed. If you press the UP button it will show
“SOUN”. Select which one you want to activate, and press ENTER.
5. Press UP, to select “ALON” or “NAST”. Which mean stand alone,
or master/slave mode.
6. Select a mode, and press ENTER to confirm.
7. Press EXIT/DN to return to the main menu
8. The unit comes with two preprogrammed shows built-in, each
show will react to low frequencies via the internal microphone.
You may change the show or invert the pan and tilt functions by
in the system menu by following the directions on page 21.
Master-Slave Operation (Sound Active): This function will allow
you to link up to 16 units together and operate without a controller. The
units will be sound activated. In Master-Slave operation one unit will
act as the controlling unit and the others will react to the controlling
units programs. Any unit can act as a Master or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units
together via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR
connector is the output. The first unit in the chain (master) will use
the female XLR connector only - The last unit in the chain will use
the male XLR connector only. For longer cable runs we suggest a
terminator at the last fixture.
2. Follow the procedures on page 16 under “SLAV”, and page 18
under “RUN” to set the master and slave units.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 29
Accu Spot 250™
Fuse & Lamp Replacement
Caution: Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ® service
technician. Replacing with anything other than the specified part can
damage your unit and will void your manufactures warranty.
Warning: If you continue to blow lamps or fuses, STOP using the
unit. Contact customer support for further instructions, you may have
to return the unit for servicing. Continuing to use the unit may cause
serious damage.
Lamp Replacement: Caution! Never attempt to change the lamp
while the fixture is plugged in. Always disconnect the main power
and allow the unit ample time to cool before attempting to replace the
lamp. Lamp replacement has been made simple by incorporating the
use of a flip-up front cover that is retained by thumb screws.
1. Be sure to follow the proper handling procedures that deal with
discharge lamps.
2. Remove the two small screws (A,B) on the rear of the unit
3. After removing the screws, gently slide out the socket assembly
from the rear of the unit to expose the lamp.
4. Carefully remove the old lamp and discard it in the trash.
5. Replace the lamp with an exact match and reassemble in reverse
order.
6. After replacing the lamp follow the optimization procedures on the
next page to be sure the lamp is center in the reflector
A
B
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 30
Accu Spot 250™
Fuse & Lamp Replacement
Optimizing Lamp Alignment: This procedure centers the lamp in
the reflector. Proper optimization will increase lamp life and ensure a
bright crisp output. Improper optimization may add a yellow tint to the
lamp output and reduce intensity.
1. Be sure main power is disconnected and allow the unit to cool. If
the you have just installed a new unit you can obviously skip this
step.
2. Make a preliminary adjustment: Turn the three lamp adjustment
thumb screws completely in (clockwise). Then back them each
out (counter-clockwise) about three complete turns.
3. Turn the unit on and allow it to reset.
4. Using either a DMX controller or the control panel on the unit,
strike the lamp and focus the light on a flat surface.
6. Center the hot-spot (the brightest part of the beam) using the 3
adjustment screws. Turn one screw at a time to drag the hot-spot
diagonally across the projected image. If you cannot detect a hotspot, adjust the lamp until the light is even.
7. To reduce a hot-spot, pull the lamp in by turning all three screws
clockwise 1/4-turn at a time until the light is evenly distributed.
8. If the light is brighter around the edge than it is in the center, or if
light output is low, the lamp is too far back in the reflector. “Push”
the lamp out by turning the screws.
Optimizing Screws
Optimizing Screws
Fuse Replacement: Locate and remove the unit’s power cord. Once
the cord has been removed located the fuse holder located inside the
power socket. Insert a flat-head screw driver into the power socket
and gently pry out the fuse holder. Remove the bad fuse and replace
with a new one. The fuse holder has a built-in socket for a spare fuse
be sure not to confuse the spare fuse with active fuse.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 31
Accu Spot 250™
DMX Traits
Channel
Value
1
0 - 255
PAN
2
0 - 255
TILT
3
0 - 199
COLOR
0 - 19
20 - 39
40 - 59
60 - 79
80 - 99
100 - 119
120 - 139
140 - 159
160 - 179
180 - 199
200 - 255
4
Function
WHITE
RED
BLUE
YELLOW
GREEN
LIGHT BLUE
AMBER
PINK
MAGENTA
PURPLE
RAINBOW EFFECT
GOBO
0 - 13
14 - 27
28 - 41
42 - 55
56 - 69
70 - 83
84 - 97
98 - 115
116 - 135
136 - 155
156 - 175
176 - 195
196 - 215
216 - 235
236 - 255
SPOT
GOBO 1 (metal)
GOBO 2 (metal)
GOBO 3 (metal)
GOBO 4 (dichoric)
GOBO 5 (metal)
GOBO 6 (metal)
GOBO 7 (metal)
GOBO 1 SHAKE
GOBO 2 SHAKE
GOBO 3 SHAKE
GOBO 4 SHAKE
GOBO 5 SHAKE
GOBO 6 SHAKE
GOBO 7 SHAKE
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 32
Accu Spot 250™
Gobos
Accu Spot 250™
Channel
7
1
2
3
4
5
6
7
8
Accu Spot 250™
Channel
Value
5
DMX Traits cont.
Function
GOBO ROTATION
0-7
8 - 127
128 - 135
136 - 255
6
NO ROTATION
FORWARDS GOBO ROTATION
FAST
SLOW
NO ROTATION
BACKWARDS GOBO ROTATION
SLOW
FAST
SHUTTER/STROBE
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
Value
DMX Traits cont.
Function
LAMP ON/OFF/RESET/INTERNAL PROGRAMS
0 - 19
COLOR CHANGE NORMAL
20 - 39 COLOR CHANGE TO ANY POSITION
40 - 59
LAMP ON
60 - 79
LAMP SWITCH OFF
80 - 99
MOTOR RESET
100 - 119
INTERNAL PROGRAM 1
120 - 139
INTERNAL PROGRAM 2
140 - 159
INTERNAL PROGRAM 3
160 - 179
INTERNAL PROGRAM 4
180 - 199
INTERNAL PROGRAM 5
200 - 219
INTERNAL PROGRAM 6
220 - 239
INTERNAL PROGRAM 7
240 - 255
SOUND ACTIVE
8
SPEED OF PAN/TILT MOVEMENT
0
MAX. SPEED
5 - 225
MAX. TO MIN. SPEED
226 - 235
BLACKOUT BY MOVEMENT
236 - 245 BLACKOUT BY WHEEL MOVEMENT
246 - 255
NO FUNCTION
SHUTTER CLOSED
DIMMER
STROBE
SLOW
FAST
SHUTTER OPEN
PULSE EFFECT
SHUTTER OPEN
RANDOM STROBE
SLOW
FAST
SHUTTER OPEN
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 33
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 34
Accu Spot 250™
Gobo Replacement
This unit comes with interchangable gobos. Changing the
gobos is a easy procedure. Follow the instructions below.
Caution! Never open the unit when in use. Always disconnect
the main power before attempting to change the gobos.
1. To change the gobo, you must remove the top half of the
moving head. The top half of the moving head does not have
the lens in front. The lens is on the bottom half of the head.
2. Unscrew the two phillips screws in the front of the moving
head and the two in the back. Remove the top half of the
shell.
3. When you remove the top shell you will be able to access the
gobo wheel. Turn the wheel with your hand until you come
across the gobo you would like to change. Now turn the
color wheel so that the empty space appears behind the
gobo that you want to change.
4. Remove the fixation-ring with a small flat-head screwdriver.
Put your finger through the empty space in the color wheel,
and push the gobo out towards the front. When doing this
you do not need a lot of pressure. You can also use tweezers
to gently pull the gobo out, or a small flat-head screwdriver
and gently pry out the gobo.
5. Change the gobo, replace the fixation-ring, and reassemble
the unit.
Accu Spot 250™
Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the
internal and external optical lenses and mirror should be carried out
periodically to optimize light output. Cleaning frequency depends on
the environment in which the fixture operates (I.e. smoke, fog residue,
dust, dew). In heavy club use we recommend cleaning on a monthly
basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft
cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Accu Spot 250™
Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1. Be sure you have connected your unit into a standard 120v wall
outlet.
2. Be sure the external fuse has not blown. The fuse is located on
the bottom panel of the unit.
3. Remove the lamp holder and be sure the lamp is seated in its
socket properly. Occasionally lamps become loose during shipping be sure the lamp is push in to its socket all the way.
4. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 35
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 36
Accu Spot 250™
Warranty
Accu Spot 250™
Notes
1-YEAR LIMITED WARRANTY
A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be
free of manufacturing defects in material and workmanship for a period of 1 Year (365 days)
from the date of purchase. This warranty shall be valid only if the product is purchased
within the United States of America, including possessions and territories. It is the owner’s
responsibility to establish the date and place of purchase by acceptable evidence, at the
time service is sought.
B. For warranty service, send the product only to the American DJ® factory. All shipping
charges must be pre-paid. If the requested repairs or service (including parts replacement)
are within the terms of this warranty, American DJ® will pay return shipping charges only
to a designated point within the United States. If the entire instrument is sent, it must be
shipped in its original package. No accessories should be shipped with the product. If any
accessories are shipped with the product, American DJ® shall have no liability whatsoever
for loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ® concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than
the American DJ® factory unless prior written authorization was issued to purchaser by
American DJ®; if the product is damaged because not properly maintained as set forth in
the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ® will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor
by reason of defects in material or workmanship. The sole responsibility of American DJ®
under this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of American DJ®. All products covered by this warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E. American DJ® reserves the right to make changes in design and/or improvements upon
its products without any obligation to include these changes in any products theretofore
manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ® in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period
set forth above. And no warranties, whether expressed or implied, including warranties of
merchantability or fitness, shall apply to this product after said period has expired. The
consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly
provided above; and under no circumstances shall American DJ® be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to American DJ® Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions
heretofore published.
H. Lamps are not covered under this or any other warranty, either written or implied.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 37
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 38
Accu Spot 250™
Model:
Voltage*:
Lamp:
Dimensions:
Colors:
Gobos:
Weight:
Fuse:
Duty Cycle:
DMX:
Sound Active:
Working Position:
Warranty:
Specifications
Accu Spot 250™
120v/60Hz or 230v/50Hz
ZB-MSD250, 230v/250w
13.5”(L) x 14”(W) x 19.5”(H)
373mm x 295mm x 451mm
9 Plus White
7 Rotating + Spot - All Replaceable
24mm Outside/ 20mm Viewable
39 Lbs. / 18 kgs.
10A (120v) / 5A (220v)
None
8 Channels
Yes
Any Safe, Secure Position
1 Year (365 days)
*Voltage is preset at the factory and is not user selectable
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
American DJ® - www.americandj.com - Accu Spot 250™ Instruction Manual Page 39
American DJ®
American DJ World Headquarters:
4295 Charter Street Los Angeles, CA 90058 USA
Tel: 323-582-2650 / Fax: 323-582-2610
Web: www.americandj.com / E-mail: info@americandj.com
Download PDF