Robin America | EH25-2 | Specifications | Robin America EH25-2 Specifications

OPERATION AND PARTS MANUAL
B-SERIES
WALK-BEHIND TROWEL
Revision #9 (07/06/10)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
P/N 11216
Engine exhaust and some of
its constituents, and some dust created
by power sanding, sawing, grinding,
drillingandotherconstructionactivities
contains chemicals known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Some examples of these chemicals are:
Leadfromlead-basedpaints.
Crystallinesilicafrombricks.
Cementandothermasonryproducts.
Arsenicandchromiumfromchemically
treatedlumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: ALWAYS work in a
well ventilated area, and work with
approved safety equipment, such as
dust masks that are specially designed
to filter out microscopic particles.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 3
B-SERIES TROWEL— TABLE OF CONTENTS
Here's How To Get Help ............................................ 3
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Training Checklist ...................................................... 6
Daily Pre-Operation Checklist ................................... 7
Safety Message Alert Symbols .............................. 8-9
Rules For Safe Operation .................................. 10-11
Operation And Safety Decals .................................. 12
Specifications (Trowel) ............................................ 12
Specifications (Engines & Electric Motor) ............... 14
Specifications (Trowel Weights) .............................. 14
General Information ................................................ 15
MQ WHITEMAN — B-SERIES TROWEL
Controls and Components ................................. 16-17
Basic Engine ........................................................... 18
Assembly and Installation .................................. 19-21
Pre-Inspection .................................................... 22-23
Initial Start-Up (Gasoline Engine) ...................... 24-25
Initial Start-Up (Electric Motor) ............................... 26
Operation ........................................................... 27-28
Options ............................................................... 29-30
Maintenance ...................................................... 31-35
Troubleshooting (Trowel) ................................... 36-37
Troubleshooting (Engine) ........................................ 38
Explanation of Codes in Remarks Column ............. 40
Suggested Spare Parts ........................................... 41
Nameplate and Decals....................................... 42-43
Standard Handle Assy. ....................................... 44-45
Quick Pitch™ Handle Assy. ............................... 46-47
Thrust Bearing Kit Assy. ..................................... 48-49
3 and 4 Blade spider Assy. ................................ 50-51
Gearbox and Engine Mounts ............................. 52-53
Engines, Honda, Robin, & Briggs & Stratton ..... 54-55
Hand Clutch Assy. (S/N LJ41888 & Below) ........ 56-57
Hand Clutch Assy. (S/N LJ41889 & Above) ....... 58-59
Electric Motor Assy. ............................................ 60-61
Guard Ring Assy. ............................................... 62-63
Stabilizer Ring Assy ........................................... 64-65
Blades and Adjustment Fixture Assy. ................ 66-67
Lifting Bale Assy. ................................................ 68-69
HONDA GX240K1 ENGINE
Air Cleaner Assy. ................................................ 70-71
Camshaft Assy. .................................................. 72-73
Carburetor Assy. ................................................ 74-75
Control Assy. ...................................................... 76-77
Crankcase Cover Assy. ...................................... 78-79
Crankshft Assy. .................................................. 80-81
Cylinder Barrel Assy. .......................................... 82-83
Cylinder Head Assy. ........................................... 84-85
Fan Cover Assy. ................................................. 86-87
Flywheel Assy..................................................... 88-89
Fuel Tank ............................................................ 90-91
Gasket Kit ................................................................ 93
Ignition Coil ........................................................ 94-95
Muffler ................................................................ 96-97
Piston ................................................................. 98-99
Recol Starter ..................................................100-101
Labels ............................................................102-103
ROBIN EH25-2 ENGINE
Crankcase Assy. ............................................ 104-105
Crankshaft Assy. ............................................ 106-107
Intake and Exhaust Assy. ............................... 108-109
Governor Assy. .............................................. 110-111
Cooling and Starting Assy. ............................. 112-113
Fuel Tank Assy. .............................................. 114-115
Carburetor Assy. ............................................ 116-117
Recoil Start Assy. ........................................... 118-119
Oil Sensor ...................................................... 120-121
Terms and Conditions of Sale — Parts ................. 122
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
www.multiquip.com
B-SERIES TROWEL— PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Order via Internet (Dealers Only):
Best Deal!
Effective:
January 1st, 2006
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
Order parts on-line using Multiquip’s SmartEquip website!
N View Parts Diagrams
N Order Parts
N Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Goto www.multiquip.com and click on
Order Parts to log in and save!
Note: Discounts Are Subject To Change
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Note: Discounts Are Subject To Change
Order via Phone: Domestic (US) Dealers Call:
1-800-427-1244
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
R
R
R
R
R
R
Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Quantity, Part Number and Description of Each Part
R
Specify Preferred Method of Shipment:
UPS/Fed Ex
DHL
N Priority One
Truck N Ground
N Next Day
N Second/Third Day
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 5
B-SERIES TROWEL— TRAINING CHECKLIST
TRAINING CHECKLIST
This checklist will lists some of the minimum requirements for
machine maintenance and operation. Please feel free to detach
it and make copies. Use this checklist whenever a new operator
is to be trained or it can be used as a review for more experienced
operator’s.
TRAINING CHECKLIST
NO.
DESCRIPTION
1
Read Operator’s Manual completely.
2
Machine layout, location of components, checking of engine and
gearbox fluid level.
3
Fuel system, refueling procedure
4
Operation of controls (machine not running).
5
Safety controls, kill switch operation.
6
Emergency stop procedures.
7
Star tup of machine.
8
Maneuvering
9
Pitching
10
Concrete finishing techniques.
11
Shutdown of machine.
12
Lifting of machine (optional equipment).
13
Machine transpor t and storage.
OK?
DATE
Operator _________________________________________ Trainee __________________________________________
COMMENTS:
PAGE 6 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL— DAILY PRE-OPERATION CHECKLIST
DAILY PRE-OPERATION CHECKLIST
DAILY PRE-OPERATION CHECKLIST
1
Engine Oil Level.
2
Gearbox Fluid Level.
3
Condition of Blades.
4
Blade Pitch Operation.
5
Safety Kill Switch Operation.
6
Clutch Operation
COMMENTS:
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 7
B-SERIES TROWEL— SAFETY MESSAGE ALERT SYMBOLS
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
NOTE
This Owner's Manual has been developed to provide
complete instructions for the safe and efficient operation
of the MQ Whiteman B-SERIES TROWEL. For engine
maintenance information, please refer to the engine
manufacturers instructions for data relative to its safe
operation.
Before using this WALK-BEHIND TROWEL, ensure
that the operating individual has read and
understands all instructions in this manual.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
HAZARD SYMBOLS
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
Explosive Fuel
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
Burn Hazards
DANGER:
You WILL be KILLED or
SERIOUSLY injured if you DO NOT follow
directions.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. NEVER operate the engine with
heat shields or heat guards removed.
WARNING:
You CAN be KILLED or
SERIOUSLY injured if you DO NOT follow
directions.
CAUTION: You CAN be injured if you
DO NOT follow directions.
Rotating Parts
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
Potential hazards associated with B-Series trowel operation will
be referenced with "Hazard Symbols" which appear throughout
this manual, and will be referenced in conjunction with Safety
"Message Alert Symbols".
PAGE 8 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL— SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
ALWAYS place the engine ON/OFF
switch in the OFF position, when the
trowel is not in use.
Over Speed Conditions
NEVER tamper with the factory settings of the
engine governor or settings. Personal injury
and damage to the engine or equipment can
result if operating in speed ranges above
maximum allowable.
NOTE
This walk-behind trowel, other property, or
the surrounding environment could be
damaged if you do not follow instructions.
Respiratory Hazard
ALWAYS wear approved respiratory
protection.
Sight and Hearing hazard
ALWAYS wear approved eye and hearing
protection.
Equipment Damage Messages
Other important messages are provided throughout this manual
to help prevent damage to your trowel, other property, or the
surrounding environment.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 9
B-SERIES TROWEL— RULES FOR SAFE OPERATION
CAUTION:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only! This equipment is
for industrial use only.
The following safety guidelines should always be used when
operating the B-Series walk-behind power trowel.
SAFETY
■ DO NOT operate or service this equipment
before reading this entire manual.
■ This equipment should not be operated by
persons under 18 years of age.
■ NEVER operate the trowel without proper protective clothing,
shatterproof glasses, steel-toed boots and other protective
devices required by the job.
■ NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
the trowel.
■ High Temperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot! components can cause serious burns.
■ The engine of this trowel requires an adequate free flow of
cooling air. NEVER operate the trowel (except electric models)
in any enclosed or narrow
area where free flow of the
air is restricted. If the air flow
is restricted it will cause
serious damage to the
trowel's engine and may
cause injury to people.
Remember the trowel's
engine gives off DEADLY
carbon monoxide gas.
■ ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■ NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
■ NEVER operate the trowel under the
influence or drugs or alcohol.
■ NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■ Manufacture does not assume responsibility for any accident
due to equipment modifications.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ ALWAYS check the trowel for loosened threads or bolts
before starting.
■ ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it
to cool.
■ NEVER smoke around or near the
machine. Fire or explosion could result from
fuel vapors, or if fuel is spilled on a hot!
engine.
■ NEVER operate the trowel in an explosive atmosphere or
near combustible materials. An explosion or fire could result
causing severe bodily harm or even death.
■ Topping-off to filler port is dangerous, as it tends to spill fuel.
PAGE 10 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL— RULES FOR SAFE OPERATION
■ DO NOT operate this trowel unless all guards and safety
devices are attached and in place. See Pages 16 and 17.
■ ALWAYS use proper lifting techniques when moving the
trowel.
■ ALWAYS check to make sure that the operating area is clear
before starting the engine.
■ ALWAYS test the safety kill switch devices before operating
the trowel.
■ NEVER place your feet or hands inside the guard rings
while starting or operating this equipment.
■ AVOID wearing jewelry or loose fitting clothing that may snag
on the controls or moving parts, this can cause a serious
injury.
■ Keep the trowel in proper running condition.
■ Make sure that there is no buildup of concrete, grease, oil or
debris on the trowel.
■ Fix damage to the trowel immediately and always replace
broken parts.
■ Dispose of hazardous waste properly. Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
■ High Temperatures – Allow the machine and engine to
cool before adding fuel or performing service and
maintenance functions. Contact with hot! components can
cause serious burns.
■ ALWAYS keep clear of rotating or moving parts while
operating the trowel.
CAUTION
■ NEVER leave the machine unattended while running.
Emergencies
■ Moving Parts – Shut down the engine before performing
service or maintenance functions. Contact with moving parts
can cause serious injury.
Maintenance Safety
■ Disconnect the spark plug wires before attempting any type
of service.
■ ALWAYS know the location of the nearest
fire extinguisher and first aid kit. Know the
location of the nearest telephone. Also know
the phone numbers of the nearest
ambulance, doctor and fire department.
This information will be invaluable in the case
of an emergency.
■ Securely support any machine components that must be
raised.
■ NEVER lubricate components or attempt service on a running
machine.
■ DO NOT use food or plastic containers to dispose of
hazardous waste.
■ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 11
B-SERIES TROWEL— OPERATION AND SAFETY DECALS
Machine Safety Decals
The B-Series walk-behind trowel is equipped with a number of safety decals. These decals are provided for operator safety and
maintenance information. Figure 1 below illustrates these decals as they appear on the machine. Should any of these decals
become unreadable, replacements can be obtained from your dealer.
Figure 1. B-Series Trowel Decals
PAGE 12 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL— SPECIFICATIONS (TROWEL)
Side View
Figure 2. B-Series Trowel Dimensions
Table 1. B-Series Trowel Specifications
A– Height (Lifting Hook)
34.5 in (876.2 mm)
B– Height Engagement Lever)
41.1 in (1,044.2 mm)
46.0 (1,168.4 mm)
C–Width
75.2 (1,910.1 mm)
D–Length
Weight – Operating
See Table 3
Sound Pressure
97 db
Vibration
2.5g (24.5 m/s2)
Ring Diameter
46 in (117 cm)
Number of Blades
3 or 4
Blade Tip Speed – FPM (m/s)
1,478 fpm (7.5 m/s)
Rotor – RPM (Gasoline)
60 to 125
Rotor – RPM (Electric)
108
Path Width – in. (cm)
48 (233)
NOTE:
1.
Sound pressure is a weighted measure. Measured at the
operators ear position while the walk-behind trowel is
operating at full throttle on concrete in a manner most often
experienced in “normal” circumstances. Sound pressure
may vary depending upon the condition of the concrete.
Hearing protection is always recommended.
2.
The vibration level indicated is the maximum RMS (Root
Mean Square) value obtained at the handle grip while
operating the walk-behind trowel on curing concrete in a
manner most often experienced in “normal” circumstances.
Values were obtained from all three axes of motion. The
values shown represent the maximum RMS value from
these measurements.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 13
B-SERIES TROWEL— SPECIFICATIONS (ENGINES & ELECTRIC MOTOR )
Table 2. Specifications (Engines & Electric Motor)
Model
HONDA GX240K1
ROBIN EH-25-2
Electric Motor
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
N/A
Bore X Stroke
2.90 in. X 2.30 in.
(73 mm x 58 mm)
2.95 in. X 2.24 in.
(75 mm x 57 mm)
N/A
Displacement
14.81 cc
15.31 cc
N/A
8.0 H.P./3600 R.P.M.
8.5 H.P./4000 R.P.M.
2.0 HP
Approx. 1.59 U.S. Gallons
(6 Liters)
Approx. 1.59 U.S. Gallons
(6 Liters)
N/A
Unleaded Gasoline
Unleaded Gasoline
N/A
2-1/3 pints
2 pints
N/A
Centrifugal Fly-weight
Type
Centrifugal Fly-weight Type
N/ A
Recoil Star t
Recoil Star t
N/ A
N/ A
N/A
115/230 VAC Single
Phase
14.0 x 16.9 X 16.1 in.
(355 X 430 X 410 mm)
14.40 x 16.20 X 17.32 in.
(366 X 412 X 440 mm)
TBD
55.1 lbs (25 Kg.)
50.7 lbs (23 Kg.)
TBD
Type
Max Output
Engine/Electric Motor
Fuel Tank Capacity
Fu e l
Lube Oil Capacity
Speed Control Method
Star ting Method
Input Voltage
Dimension (L x W x H)
Dry Net Weight
Table 3. Specifications (Trowel Weights)
MODEL
POWER SOURCE
OPERATING WEIGHT
SHIPPING WEIGHT
B-3-8H
8 HP Honda
237 lbs. (107 kg.)
286 lbs. (130 kg.)
B-4-8BS
8 HP Briggs and Stratton
228 lbs. (103 kg.)
278 lbs. (126 kg.)
B-4-7R
7.5 HP Robin
237 lbs. (107 kg.)
287 lbs. (130 kg.)
B-4-7RM
7.5 HP Robin, Manual Clutch
237 lbs. (107 kg.)
287 lbs. (130 kg.)
B-4-8H
8.0 HP Honda
242 lbs. (110 kg.)
292 lbs. (132 kg.)
B-4-8HM
8.0 HP Honda, Manual Clutch
242 lbs. (110 kg.)
292 lbs. (132 kg.)
B-4-2E
2 HP, 115/230, Single-Phase
179 lbs. (81 kg.)
229 lbs. (104 kg.)
PAGE 14 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL— GENERAL INFORMATION
B-Series Walk-Behind Trowel Familiarization
Blades
This walk-behind trowel is designed for the floating and
finishing of concrete slabs.
The blades of the trowel finish the concrete as they are rotated
around the surface. Blades are classified as combination (8
inches wide), float (10 or 8 inches wide), and finish (6 inches
wide). This trowel comes equipped with either three or four
blades per rotor equally spaced in a radial pattern and
attached to vertical rotating shaft by means of a spider
assembly.
Take a walk around the trowel. Take notice of all the major
components (see Figure 3, pages 16 and 17) like the engine,
blades, quick pitch control, air cleaner, centrifugal stop switch
etc. Check that there is always oil in the engine.
Read all the safety instructions carefully. Safety instructions will
be found throughout this manual and on the trowel. Keep all
safety information in good, readable condition. Operators should
be well trained on the operation and maintenance of the trowel.
Before using your trowel, test it on a flat watered down section of
finished concrete that is free of any debris and other objects.
This trial test run will increase your confidence in using the trowel
and at the same time it will familiarize you with the trowel’s
controls. In addition you will understand how the trowel handles
under actual conditions.
Centrifugal Stop Switch
In the event of a trowel runaway condition (operator releases
the handle), a centrifugal stop switch, manual clutch or
micro-switch depending which trowel you have, will stop
the engine and bring the trowel to a halt.
CAUTION
NEVER attempt to lift the trowel by yourself.
ALWAYS get the assistance of another
person to help lift the trowel or use a crane or
lifting device to move the trowel.
Engines
This trowel is available with either an 8.0 HP HONDA, 8.5 HP
ROBIN, or a 8.0 HP Briggs and Stratton gasoline engine. In
addition, a 2.0 horsepower 115/230 VAC, single phase electric
motor is also available. Refer to the engine owner’s manual for
instructions regarding the operation and maintenance of your
engine. The engine manual is included with your trowel at the
time of shipping from Whiteman. Please contact your nearest
Multiquip Dealer for a replacement should the original manual
disappear.
Drive System
Power is transferred from the engine or electric motor to the
gearbox input shaft via a V-belt or pulley drive system. The pulley
engages using either a centrifugal or manual clutch. See page
23.
Gearbox
The gearbox is located beneath the engine and transfers power
to the rotor or spider assembly. The gearbox controls the
rotational speed of the trowel and is equipped with two shafts
(input and output).
Moving the B-Series Walk-Behind Trowel
This walk-behind trowel is designed to be moved and handled
in several ways. The easiest way to lift the trowel is to use the
auxiliary lifting tube that is attached to the main handle. See
page 24, Figure 19. When using the auxiliary tube, always use
two persons to lift the trowel.
Some models have a lifting bale (option) installed. A strap or
chain can be attached to the lifting bale, allowing a forklift or
crane to lift the trowel up onto a slab of concrete. Use a lifting
device of adequate lifting capacity to lift the trowel.
Training
For proper training, please use the “TRAINING CHECKLIST”
located in the front of this manual (Page 6). This checklist will
provide an outline for an experienced operator to provide training
to a new operator
Spider
The vertical output shaft of the gearbox connects to a cast hub
called the spider. The spider has either 3 or 4 arms that extend
outward that are used for attachment of blades or other
accessories. Remember as the gearbox output shaft rotates so
does the spider assembly.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 15
B-SERIES TROWEL— CONTROLS AND COMPONENTS
Figure 3. B-Series Walk-Behind Trowels
PAGE 16 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL— CONTROLS AND COMPONENTS
Figures 3 shows the location of the basic controls or components,
for the B-Series trowel. Listed below is a brief explanation of
each control or component
1.
2.
3.
Quick Pitch™ Control Handle – To adjust the pitch of
the blades, grasp the handle then squeeze and either move
the handle forward or backward to achieve the desired
blade pitch.
10. Trowel Lifting Point – Insert the auxiliary lifting tube here.
See Figure 19.
11. AC Power Plug (Electric Models Only) – Insert this plug
into an AC power source.
12. Micro-Switch (Electric Models Only) – In the event the
operator loses control of the trowel, this micro-switch will
shut-down the electric motor.
Throttle Control Lever – Controls the speed of the engine.
Move the hand lever towards the operator to increase
engine speed (high), away from the operator to decrease
engine speed (low).
13. Electric Switch Box (Electric Models Only) – Provides
AC power to the electric motor.
Hand Grip/Handle Bar – When operating the trowel, place
both hands on each grip to maneuver the trowel. Replace
hand grips when they become worn or damaged.
15. Electric Motor (Electric Models Only) – This trowel uses
a 2 HP, 115/230 VAC single phase electric motor.
14. Guard Ring- NEVER! put hands or feet inside guard ring.
16. Trowel Arm – NEVER operate the trowel with a bent, broken
or out of adjustment trowel arm. If the blades show uneven
wear patterns or some blades wear out faster than others,
the trowel arm may need to be adjusted. Use the trowel
arm adjustment tool P/N 1817 to adjust the trowel arms.
4.
Centrifugal Kill Switch – In the event the operator looses
control of the trowel, this switch will shut-down the engine.
5.
Engine – This trowel uses Honda, Robin and Briggs and
Stratton type gasoline engines.
6.
Auxiliary Lifting Tube - Use this tube to lift the trowel onto
a slab. Tube is to be inserted into socket located in front of
the gearbox.
7.
Pitch Control (standard models) - Turn this "Star Wheel"
clockwise for increase blade pitch, and counter-clockwise
for decrease blade pitch.
18. V-Belt Cover – Remove this cover to gain access to the Vbelt. NEVER operate the trowel with this cover removed.
8.
Clutch Lever - Clutch engagement lever. When this lever
is engaged, the blades will begin to rotate. May be used
with either Quick Pitch™ or Standard handle.
19. Weights – The trowel may be equipped with two 10 lbs.
weights. The weights may be removed to reduce the
operating weight of the trowel.
9.
Main Tube - When disassembling components inside the
tube exercise extreme CAUTION! Tube is spring-loaded,
severe injury could result if not disassembled correctly.
20. Stabilizer Ring – Reduces trowel arm vibration. Helps
stabilize trowel arm.
17. Blades – This trowel is equipped with combination blades.
These blades are versatile and should take care of most
troweling needs. In addition float discs can be attached to
the trowel arms that will allow the trowel to float on "wet"
concrete.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 17
B-SERIES TROWEL— BASIC ENGINE
HONDA engine shown.
Figure 4. Engine Controls and Components
INITIAL SERVICING
The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions & details of operation and servicing. The
engine shown above is a HONDA engine, operation for other
types of engines may vary somewhat.
1.
5.
Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
6.
Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7.
Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
NOTE
Operating the engine without an air filter,
with a damaged air filter, or a filter in need of
replacement will allow dirt to enter the
engine, causing rapid engine wear.
DANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity to
cool down. In the event of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been completely wiped up, and the
area surrounding the engine is dry.
2.
Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
3.
Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4.
Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
8.
Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
9.
Muffler – Used to reduce noise and emissions.
WARNING
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
PAGE 18 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — ASSEMBLY AND INSTALLATION
Assembly and Installation
Quick Pitch™ Handle Installation (Quick Pitch Models Only)
Before the trowel can be put into operation there are some
components that must be installed before the trowel can be used.
This section explains how to install those components.
CAUTION
The Quick Pitch™ handle is spring loaded,
personal injury or damage could result from
improper handling or installation. Be careful
when installing this component.
Handle Tube Installation (All Models)
1.
Install the handle tube to the gearbox as shown in Figure 5.
The mounting hardware should be contained in the shipping
container.
NOTE
Considerable force may be required when
moving the Quick Pitch ™ T-handle
forward or backward.
1.
Grasp the Quick Pitch™ T-handle from the operator's
position and squeeze the blade pitch adjustment trigger.
Move the T-handle towards the engine as far as possible
(Figure 6). This will compress the spring inside the handle
tube. Allowing maximum exposure of the pitch cable.
Figure 5. Handle Tube Installation
Figure 6. Blade Pitch T-Handle
2.
Lock the spring in the compressed position, by releasing
the blade pitch adjustment trigger.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 19
B-SERIES TROWEL — ASSEMBLY AND INSTALLATION
3.
Remove one brass set nut from the Quick Pitch™ cable
end as shown in Figure 7.
4.
Thread the second brass set nut towards the cable as far
as possible.
Pre-load Adjustment (Quick Pitch™ Models Only)
1.
After the Quick Pitch™ handle has been installed on the
trowel, spring pre-load adjustment will be required.
2.
Locate the adjustment screw on the underside of the handle
tube (Figure 9).
Figure 7. Quick Pitch™ Cable
5.
Insert the cable end through the yoke eyelet (Figure 8)
Tighten the first brass set nut by hand to remove all the
slack from the cable.
6
Using a wrench, tighten the second brass set nut up against
the yoke boss. This will lock the cable in place.
7.
Use a wrench and finish tightening the first brass set nut up
against the yoke boss.
Figure 9. Cable/Yoke Attachment
3.
A decal has been placed on the side of the handle tube to
assist the user in the adjustment of the spring.
4.
Align the arrow on the adjustment screw with the letter "B"
COMBO on the decal. The letter "B" stands for B-Series
Walk-Behind trowel.
5.
Test the pitch control operation and adjust if necessary.
Throttle Cable Installation (Honda and Robin Engines)
1.
Figure 8. Cable Yoke Attachment
Set the throttle lever (Figure 10) to the idle position by
pushing it away from the operator’s position towards the
engine.
Figure 10. Throttle Lever
PAGE 20 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — ASSEMBLY AND INSTALLATION
2.
On ROBIN engines, the hook-on the engine end of the
throttle wire must be removed. Make the cut as shown in
Figure 11. The HONDA engine will not require this
modification to the throttle cable.
5. Connect the throttle cable to the engine. Keep in mind there
should be a piece of wire installed on the trowel to show you
where to route the throttle cable. When connecting the cable
housing, make sure that no more than 1/4" (6.4mm) of the
cable housing protrudes past the housing clamp on the
engine (Step 4).
6. After the cable has been installed on the engine, tighten the
clamp on the throttle control, operator position of the handle
to lock the throttle cable at the proper length.
7. These are general instructions. Installation of the throttle
cable may vary for different engine configurations. Please
look for more detailed instructions inside the box containing
the handle.These more detailed instructions should provide
adequate guidance for installing.
Figure 11. Throttle Wire Hook
3.
Connect the throttle cable hook-on wire to the HONDA
engine throttle lever as shown in Figure 12.
Safety Kill Wire
Locate the RED wire protruding from the handle tube (Figure14)
and connect it to the RED tail wire on the engine. Test the kill
switch to insure proper operation.
Figure 12. Throttle Cable Connection (HONDA)
4. Connect the throttle cable hook-on wire to the ROBIN engine
throttle lever as shown in Figure 13.
Figure 14. Engine Kill Wire Connection
Handle Height Adjustment
Figure 13. Throttle Cable Connection (ROBIN)
If handle height adjustment is desired, a handle wedge kit can be
purchased for your trowel by ordering Part Number 2576 from
your Multiquip dealer. These wedges are placed between the
handle and the gearbox to adjust the operating height of the
handle. This kit comes complete with wedges, new bolts and
installation instructions. This will move your operating handle
position up or down approximately 3” (76mm).
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 21
B-SERIES TROWEL— PRE-INSPECTION
CAUTION
NEVER operate the trowel
in a confined area or
enclosed area structure
that does not provide ample
free flow of air.
ALWAYS wear approved eye and hearing
protection before operating the trowel.
NEVER place hands or feet inside the guard
rings while the engine is running. ALWAYS shut
the engine down before performing any kind
of maintenance service on the trowel.
Figure 15. Engine Oil Dipstick (Removal)
3. Insert and remove the dipstick without screwing it into the filler
neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 16), fill to the edge of the oil filler
hole with the recommended oil type (Table 4). Maximum oil
capacity is 400 cc.
It is recommended that the trowel's kill switch be used to stop
the engine after every use. Doing this will verify that the switch is
working properly and presents no danger to the operator.
NOTE
Reference manufacturer engine manual for
specific servicing instructions.
Before Starting
1. Read safety instructions at the beginning of manual.
2. Clean the trowel, removing dirt and dust, particularly the
engine cooling air inlet, carburetor and air cleaner.
3. Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
4. Check carburetor for external dirt and dust. Clean with dry
compressed air.
5. Check fastening nuts and bolts for tightness.
Figure 16. Engine Oil Dipstick (Oil Level)
Table 4. Oil Type
Engine Oil Check
1. To check the engine oil level, place the trowel on secure level
ground with the engine stopped.
2. Remove the filler dipstick from the engine oil filler hole
(Figure 15) and wipe it clean.
Season
Temperature
Oil Type
Summer
25°C or Higher
SAE 10W-30
Spring/Fall
25°C~10°C
SAE 10W-30/20
Winter
0°C or Lower
SAE 10W-10
PAGE 22 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL— PRE-INSPECTION
Explosive Fuel
V-belt Check
A worn or damaged V-belt can adversely affect the performance
of the trowel. If a V-belt is defective or worn simply replace the Vbelt as outlined in the maintenance section of this manual.
Fuel Check
Blade Check
Motor fuels are highly flammable and can be dangerous if
mishandled. DO NOT smoke while refueling. DO NOT attempt
to refuel the trowel if the engine is hot! or running.
Check for worn or damaged blades. Check to see if one blade is
worn out while the others look new. If this is the case there could
be a blade pitch problem. Refer to the maintenance section of
this manual for blade pitch adjustment procedure. Replace any
worn blades.
CONTROLS
1. Remove the gasoline cap located on top of fuel tank.
Safety Kill Switches
2. Visually inspect to see if fuel level is low. If fuel is low, replenish
with unleaded fuel.
This trowel has been equipped with a safety kill switch or a hand
operated clutch. Safety kill switches should be tested every time
the engine is started.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
Gearbox Oil
1.
Determine if the gearbox oil is low by removing the oil
plug located on the side of the gearbox. This plug will be
marked by the "check" decal. See Figure 17. The correct
level of the lubrication oil should be to the bottom of the fill
plug.
NOTE
NEVER! disable or disconnect the kill switch.
It is provided for operator safety. Injury may
result if it is disable, disconnected or
improperly maintained.
Centrifugal Type Kill Switch
Located on the main handle tube is a red switch (Figure 18).The
switching mechanism of this switch should operate freely and
should always be kept in this condition. With the switch in the OFF
position, the engine should not start or run. The purpose of this
switch is to stop the engine in a runaway situation, (i.e.-the
operator releasing the handle during operation).
Figure 17. Gearbox
2.
3.
If lubrication oil begins to seep out as the drain plug is
being removed, then it can be assumed that the gearbox
has a sufficient amount of oil.
If lubrication oil does not seep out as the drain plug is
being removed, fill with type ISO 680 (Whiteman P/N 10139)
gearbox lubricant oil until the oil filler hole overflows.
Figure 18. Centrifugal Kill Switch
Hand Clutch
Some finisher models are equipped with a hand operated
clutch. These units are not equipped with a safety kill switch since
the unit automatically stops rotating when the clutch lever is
released. Clutch operation should be tested each time the machine
is started.
DO NOT let the machine sit unused with the engine at high speed
for an extended period of time. It will cause premature belt wear
or may destroy the belt. Always set the engine speed to idle when
the hand clutch is disengaged.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 23
B-SERIES TROWEL — INITIAL START-UP (GASOLINE ENGINE)
CAUTION
The trowel is heavy and awkward to move
around. Use proper heavy lifting procedures
and DO NOT lift the trowel by the guard
rings.
Lifting the Trowel Onto a Slab.
Auxiliary Lifting Tube
Remove the auxiliary lifting tube located on top of the main handle.
Insert the tube into the socket located on the opposite side of the
gearbox (Figure 19) from the handle.
Make sure that the hole in the tube engages with the pin in the
socket. With one person lifting from the main handle, and another
lifting from the auxiliary lifting tube pick up the machine to move
onto a slab.
This section is intended to assist the operator with the initial
start-up of the walk-behind trowel. It is extremely important that
this section be read carefully before attempting to use the trowel
in the field.
DO NOT use your trowel until this section is thoroughly
understood
CAUTION
DO NOT attempt to operate the trowel until
the Safety, General Information and
Inspection sections of this manual have
been read and thoroughly understood.
Depending on engine manufacturer,
operating steps may vary. See engine
manufactures operating manual. The
following start-up procedure makes
reference to a HONDA 13 HP Engine
(Manual Start)
Starting the Engine (HONDA engine)
1. Place the engine fuel valve lever (Figure 20) to the "ON"
position.
Figure 19. Lifting the Trowel
CAUTION
The trowel must be stabilized by the person
carrying the operator’s handle (Figure 19).
If it is not stabilized properly the handle may
swing around and flip the trowel, thus causing
damage to the trowel and bodily injury.
Lifting Bale (Option)
Figure 20. Engine Fuel Valve Lever
2. Place the trowel's throttle lever (Figure 21) to the "ON"
position.
The lift bale is optional on new trowels. It provides an optimal lift
point for moving the trowel. Lift bales or forklift can be used to
lift a trowel up onto a building with a crane. See “Optional
Equipment” section in this manual for ordering information.
Using a crane to move a machine with a lift bale is highly
recommended, and is perfectly safe for the machine. Extra care
should be taken when lifting the machine off the ground, though.
Serious damage to the machine or personal injury could be
caused by dropping a trowel.
Figure 21. Throttle Lever (Idle Position)
PAGE 24 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — INITIAL START-UP (GASOLINE ENGINE)
3. Place the centrifugal kill switch (Figure 22) in the "ON"
position. For models that use this feature.
6. If the engine has started, slowly return the choke lever
(Figure 23) to the CLOSED position. If the engine has not
started repeat steps 1 through 5.
NEVER disable or disconnect the centrifugal
kill switch. It is provided for the operators’
safety and injury may result if it is disabled,
disconnected or improperly maintained.
7. Before the trowel is placed into operation, run the engine for
several minutes. Check for fuel leaks, and noises that would
associate with a loose guard ring and/or covers.
8. To begin troweling, place the throttle lever (Figure 21) in the
"RUN" position
Figure 22. Centrifugal Kill Switch
4. Place the Choke Lever (Figure 23) in the "OPEN " position
Figure 25. Throttle Lever (Run Position)
Figure 23. Engine Choke Lever
5. Grasp the starter grip (Figure 24) and slowly pull it out. The
resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly
and smoothly for starting.
Figure 24. Starter Grip
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 25
B-SERIES TROWEL — INITIAL START-UP (ELECTRIC MOTOR)
Starting The Electric Motor (Single Phase 115/230 Volts)
The electric motor used on the B-Series trowel has two operating
voltages:
■ 115 VAC Single Phase, 2 Horsepower
■ 230 VAC Single Phase, 2 horsepower
4. Squeeze the micro-switch lever ( Figure 26) to begin troweling. This lever will act an emergency stop switch. When
this lever is released, voltage to the electric motor will be
interrupted. When this lever is squeezed the voltage will
resume.This can only be accomplished if the trowel's power
ON/OFF switch is in the ON position.
1. Lift the trowel onto the slab in the same manner as described
on page 24 ("Lifting the Trowel Onto a Slab").
2. Connect one end of a heavy duty extension cord to the
AC power plug on the trowel.
3. Connect the other end of the extension cord to an AC power
source.
NOTE
Make sure to connect the correct AC voltage
(115 or 230 VAC) to the electric motor.
Connecting an incorrect voltage could cause
serious damage to the electric motor. The
identification plate located on the motor will
indicate the motor's voltage requirement.
Extension Cable
Figure 26. Electric Motor Trowel
When electric power is to be provided to the trowel at some
distance from the power source, extension cords are normally
used. Cables should be sized to allow for distance in length and
amperage so that the voltage drop between the power source
and point of use (trowel) is held to a minimum. Use the cable
selection chart (Table 5) as a guide for selecting proper extension
cable size.
NOTE
At 115
VAC the motor should draw about 16.6
Specification and part number
ampsare
andsubject
at 230 VAC
the motor
should draw
to change
without
about 8.4 amps. notice.
Table 5. Cable Selection (60 Hz, Single Phase Operation)
Load In Watts
Current in
Amperes At 120 At 240
Volts
Volts
Maximum Allowable Cable Length
#10 Wire
#12 Wire
#14 Wire
#16 Wire
2.5
300
600
1000 ft.
(305 m)
600 ft.
(183 m)
375 ft.
(107 m)
250 ft.
(76 m)
5
600
1200
500 ft.
(152 m)
300 ft.
(91 m)
200 ft.
(61 m)
125 ft.
(38 m)
7.5
900
1800
350 ft.
(107 m)
200 ft.
(61 m)
125 ft.
(38 m)
100 ft.
(30 m)
10
1200
2400
250 ft.
(76 m)
150 ft.
(45 m)
100 ft.
(30 m)
15
180 0
3600
150 ft.
(46 m)
100 ft.
(30 m)
65 ft.
(19 m)
20
2400
4800
125 ft.
(38 m)
75 ft.
(22 m)
50 ft.
(15 m)
30
3600
7200
75 ft.
(23 m)
50 ft.
(15 m)
35 ft.
(11 m)
CAUTION: Equipment damage can result from low voltage.
PAGE 26 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — OPERATION
The following steps are intended as a basic guide to machine
operation, and are not to be considered a complete guide to
concrete finishing. We suggest that all operators (experienced
and novice) read “Slabs on Grade” published by the American
Concrete Institute, Detroit, Michigan. Read the “Training”
section of this manual for more information.
Pitching The Blades.
Quick Pitch Handle
1. To pitch the blades upwards using the "Quick Pitch™"
T-handle , (Figure 27) simply squeeze the trigger lock
and pull the T-handle towards the operator. Pushing
the T-handle towards the engine will cause the blades
to lay flat.
Maneuvering the Trowel
1. Get into the operator’s position behind the handle. With a
secure foothold and a firm grasp on the handles slowly
increase the engine speed until the desired blade speed is
obtained.
If your trowel has a hand clutch (Figure 29), set your engine
speed with the throttle, then pull on the hand clutch lever to
start the blades turning. Adjust the blade speed after the hand
clutch is fully engaged.
Figure 29. Hand Clutch Lever
Figure 27. Quick Pitch™ T- Handle
Standard Handle
If your trowel has an electric motor, Squeeze the microswitch lever ( Figure 30) to begin turning the blades. This
lever will act an emergency stop switch. When this lever
is released, voltage to the electric motor will be interrupted.
When this lever is squeezed the voltage will resume.This can
only be accomplished if the trowel's power ON/OFF switch
is in the ON position.
1. To pitch the blades upwards using the "Standard" handle,
(Figure 28) simply turn the star-wheel clockwise.Turning the
star wheel counter clockwise will cause the blades to lay flat.
Figure 30. Micro-Switch Engagement Lever
2. To maneuver the trowel, gently lift up on or press down on the
main trowel handle. To move the machine to the operator’s
left, lift up on the handle, to move machine to the right, push
down on the handle.
3. The best method for finishing concrete is to slowly walk
backwards (Figure 31) with the trowel, guiding the trowel
from side to side. This will cover all footprints on wet concrete.
Figure 28. Standard Handle
4. Remember that if you let go of the trowel, just step away and
let the trowel come to a complete stop before trying to recover
the trowel.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 27
B-SERIES TROWEL — OPERATION
Figure 31 below illustrates a typical walk-behind trowel
application. Practice maneuvering the trowel. The trick is to let
the trowel do the work.
Continue to practice maneuvering the trowel. Try to practice as if
you were finishing a slab of concrete. Practice edging and
covering a large area. Remember a good finishing technique is
to work backwards. Be careful when moving backwards so that
hazards can be avoided. The best way to get accustomed to the
trowel is repeated use.
Figure 31. Maneuvering The Trowel
CAUTION
CAUTION
NEVER place your feet or hands inside the
guard rings while starting or operating this
equipment.
ALWAYS keep clear of rotating or moving
parts while operating this equipment.
PAGE 28 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — OPTIONS
Clip-On Float Blades (Optional)
Blades
NOTE
Blades
should be changed when they fail to
Specification and part number
finishare
concrete
in atosatisfactory
manner.
subject
change without
notice.
Blades are a vital part of finishing concrete. This Whiteman
finisher has been designed to finish concrete and are built to
stringent quality standards out of the finest trowel steel. If you need
replacement blades, consult your parts list in this manual for part
numbers and order them from your Multiquip parts dealer or
importer.
Combo Blades
This trowel was equipped with combination FLOAT/FINISH
(Figure 32) blades as original equipment. These blades have
been designed for optimum performance in both the floating and
finishing operations. These blades are versatile and should take
care of most troweling needs.
These blades will clip (Figure 34) on to an existing installed
blade, allowing your finisher to float on “wet” concrete so that the
troweling operation can begin as early as possible. They are
easily removable, so that after the floating operation, when the
concrete is sufficiently cured, they can be removed to expose the
finish blades for continued troweling.
Figure 34. Clip-On Float Blade
Float Discs (Optional)
These round discs (Figure 35) attach to the spiders and allow the
machine to “float” on “wet” concrete. The disc design allows early
floating and easy movement from wet to dry areas. They are also
very effective in embedding large aggregates and surface
hardeners.
Figure 32. Combination Blade
Finish Blades (Optional)
These blades (Figure 33) have been specifically designed for
finish operations with this trowel. They will provide a premium
surface finishing capability from your trowel. They should only be
used after the concrete has set to the point where the trowel does
not sink into the concrete when placed on it.
Figure 35. Float Disk
Figure 33. Finish Blade
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 29
B-SERIES TROWEL — OPTIONS
Grinding Attachments
Trowel Arm Adjustment Tool
Available grinding attachments are used for grinding surface
imperfections or joints.These attachments allow greater utilization
of your trowel. Figure 36 illustrates a typical grinding disk assembly,
complete with hub and stone mounting plate.
If blades show uneven wear patterns or some tend to wear out
faster than others, the trowel arms may need to be adjusted.
Whiteman makes a special tool (Figure 38) that will adjust all of
the trowel arms consistently. The Trowel Arm Fixture P/N is 1817.
Figure 38. Trowel Arm Adjustment Fixture
Figure 36. Grinding Disk
Lifting Bale
There is a heavy duty, center balance type lifting bale (Figure 37)
made specifically for your trowel. These bales are ideal for lifting
and transporting your trowel. They are designed to lift the finisher
and balance it on it’s center of gravity, providing great stability
while lifting. This option is not available on electric trowel models.
Figure 37. Lifting Bale
PAGE 30 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — MAINTENANCE
NOTE
See the engine manual supplied with your
machine for appropriate engine maintenance
schedule and troubleshooting guide for
problems.
At the front of the book (Page 7) there is a “Daily Pre-Operation
Checklist ”. Make copies of this checklist and use it on a daily
basis.
Trowel Arm adjustment Procedure
NOTE
The following procedure should be followed
to adjust trowel arms when it becomes
apparent that the trowel is finishing poorly or
in need of routine maintenance.
CAUTION!
A level, clean area to test the trowel prior to and after is essential.
Any unlevel spots in the floor or debris under the trowel blades
will give an incorrect perception of adjustment. Ideally, a 5 x 5"
three-quarter inch thick flat steel plate should be used for testing.
ALWAYS allow the engine to cool before
servicing. NEVER attempt any maintenance work
on a hot! engine.
1. To determine which blades need adjustment, place the
trowel in the test area (three-quarter inch thick plate) and look
for the following conditions:
■ Pitch the blades as flat as possible and look at the
adjustment bolts. They should all barely make contact
with the lower wear plate on the spider. If you can see
that one of them is not making contact, some adjustment
will be necessary.
MAINTENANCE SCHEDULE
Daily (8-10 Hours)
1.
Check the oil level in the engine crankcase and gear box,
fill as necessary.
2.
Check V-belt.
Weekly (50-60 Hours)
1.
Relube arms, thrust collar and clutch
2.
Replace blades if necessary.
3.
Check and clean or replace the engine air filter as
necessary.
4.
Replace engine oil and filter as necessary, see engine
manual.
Monthly (200-300 Hours)
1.
Remove, clean, reinstall and relube the arms and thrust
collar. Adjust the blade arms.
2.
Remove, clean, reinstall clutch
■ Is the machine wearing out blades unevenly (i.e. one
blade is completely worn out while the others look new)?
Figure 39 below illustrates a "worn spider bushings or bent
trowel arms". Check to see that adjustment bolt is barely
touching (0.10" max. clearance) lower wear plate. All alignment
bolts should be spaced the same distance from the lower wear
plate.
Figure 39. Worn Spider Plate
Figure 40 below illustrates the "correct alignment " for a spider
plate (as shipped from the factory).
Yearly (2000-2500 Hours)
1.
Check and replace if necessary the arm bushings, thrust
collar bushings and shaft seals.
2.
Check pitch control cables for wear.
3.
Adjust blade speed.
Figure 40. Correct Spider Plate Alignment
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 31
B-SERIES TROWEL — MAINTENANCE
2. Start engine, and bring trowel blades up to full speed and look
for the following conditions:
■ Does the trowel have a perceived rolling or bouncing
motion when in use?
■ Look at the trowel while it is running, does the guard
ring “rock up and down” relative to the ground?
Spider Removal
b. Loosen the jam nut and cone point square head set
screw, and carefully lift the upper trowel assembly off
of the spider assembly. A slight tap with a rubber mallet
may be necessary to dislodge the spider from the main
shaft of the gearbox.
c. If the trowel is equipped with an outer stabilizer ring
(Figure 42), remove the four bolts at the end of each
spider arm.
1. Once it is determined that an adjustment is required, remove
the spider assembly from the gearbox shaft as follows:
a. Locate the cone point square head set screw (Figure 41)
and attached jam nut found on the side of the spider
assembly.
Figure 42. Stabilizer Ring
d. Examine stabilizer ring for out of round or bends. If ring
is damaged, replace ring. If ring is found to be correct with
no damage, set aside.
Trowel Arm Removal
1. Each trowel arm is held in place at the spider plate by a hex
head bolt (zerk grease fitting) and a roll pin. Remove both the
hex head bolt and the roll pin (Figure 43) from the spider
plate.
2. Remove the trowel arm from the spider plate.
Figure 41. Spider/Gearbox Removal
Figure 43. Removing Roll Pin
and Zerk Grease Fitting
PAGE 32 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — MAINTENANCE
3. Should the trowel arm inserts (bronze bushing ) come out
with the trowel arm, remove the bushing from the trowel arm
and set aside in a safe place. If the bushing is retained inside
the spider plate, carefully remove the bushing.
4. Examine the bronze trowel arm bushing insert (Figure 44),
clean if necessary. Replace bushing if out of round or worn.
Trowel Arm Flatness Test
1. Using a piece of 3/4 inch thick steel plate or any surface which
is true and flat, check all six sides of each trowel arm for
flatness.
2. Check each of the six sides of the trowel arm (hex section
only) using a ten thousands of an inch (max.) feeler gauge
(Figure 46) between the flat of the trowel arm and an extremely flat test surface.
Figure 44. Bronze Bushings
Trowel Blade Removal
1. Remove the trowel blades from the trowel arm by removing
the three hex head bolts (Figure 45) from the trowel arm. Set
blades aside.
Figure 46. Trowel Arm Flatness Test
3. If the trowel arm is found to be uneven or bent, replace the
trowel arm. A bent trowel will not allow the trowel to operate
in a smooth fluid rotation.
Figure 45. Trowel Blades
2. Wire brush any build-up of concrete from all six sides of the
trowel arm. Repeat this for the remaining three arms.
4. Next, check each of the six sides of the round machined shaft
section of the trowel arm. Each section should have the same
clearance between the round of the trowel arm shaft and the
test surface.
NOTE
Trowel arms can be damaged by rough
handling or by striking exposed plumbing or
forms while in operation. ALWAYS look-out
for objects which might cause damage to the
trowel arms.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 33
B-SERIES TROWEL — MAINTENANCE
Trowel Arm Adjustment
Shown in Figure 47 is the adjustment fixture with a trowel arm
inserted. As each trowel arm is locked into the fixture, the arm bolt
is adjusted to where it contacts a stop on the fixture. This will
consistently adjust all of the trowel arms, keeping the finisher as
flat and evenly pitched as possible.
1. Locate the trowel arm adjustment tool P/N 1817. Set the
adjustment tool for a clock-wise blade rotation, meaning the
fixture arm is in the "UP" position.
3. Un-screw the locking bolts on the adjustment tool, and place
the trowel arm into the adjustment fixture channel as shown
in Figure 47. A thin shim may be required to cover the blade
holes on the trowel arm. Make sure to align the trowel
adjustment bolt with the fixture adjustment bolt.
4. Using an allen wrench, tighten the locking bolts on the
adjustment tool and securely lock the trowel arm in place.
5. Loosen the locking nut on the trowel arm lever, then turn the
trowel arm adjusting bolt until it barely touches (.010") the
adjusting bolt on the fixture.
6. After the correct adjustment has been made, tighten lock nut
on trowel arm lever to lock in place.
7. Loosen locking bolts on adjustment fixture, and remove
trowel arm from fixture.
8. Repeat steps 2-7 for the remaining trowel arms.
Re-Assembly
1. Clean and examine the upper/lower wear plates and thrust
collar. Examine the entire spider assembly. Wire brush any
concrete or rust build-up. If any of the spider components are
found to be damaged or out of round, replace them.
2. Make sure that the bronze trowel arm bushing is not damage
or out of round. Clean the bushing if necessary. If the bronze
bushing is damage or worn, replace it.
3. Reinstall bronze bushing onto trowel arm.
4. Repeat steps 2 -3 for each trowel arm.
5. Make sure that the spring tensioner is in the correct position
to exert tension on the trowel arm.
6. Insert all trowel arms with levers into spider plate (with bronze
bushing already installed) using care to align grease hole on
bronze bushing with grease hole fitting on spider plate.
Figure 47. Trowel Arm Adjustment Tool
2. Trowels manufactured prior to June of 1982 require that the
distance from the end of the adjusting bolt and the fixture arm
must be 7/8" (Figure 47). Conversely, trowels manufactured
after June of 1982 require that the distance from the end of
the adjusting bolt and the fixture arm must be 1/2".
7. Lock trowel arms in place by tightening the hex head zerk
grease fitting and jam nut.
8. Re-install the blades back onto the trowel arms
8. Install stabilizer ring onto spider assembly.
9. Reinstall lower wear plate, thrust collar and upper wear
ring in the reverse order that they were dis-assembled onto
the spider shaft. Make sure that there is little or no lateral
movement between the thrust collar and the spider shaft.
PAGE 34 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — MAINTENANCE
10. Carefully lift the upper trowel assembly, line up the keyway on gear box main shaft and insert into spider assembly
11. Reinstall square head cone point into spider plate and
tighten in place. Tighten jam nut. Use care in making sure
point of set screw engages groove in gear box main shaft.
12. Lubricate all grease points (zerk fittings) with premium
"Lithum 12" based grease, conforming to NLG1 Grade #2
consistency.
Testing
1. Place trowel in test area, start engine and test trowel for
smoothness.
Hand Clutch Adjustment
Some trowels are equipped with a hand-operated clutch instead
of an automatic centrifugal clutch. Two types of hand clutches
have been installed. Both are belt-tightener type clutches. They
operate by removing slack in the V-belt which then transmits
power from the engine to the gearbox.
There are two reasons to adjust the hand clutch: 1) operator
comfort; 2) initial belt stretch and break-in.
The easiest and most simple adjustment is to adjust the clutch
cable housing using the adjustment nut (Figure 48) located on the
clutch lever. Rotating the nut provides either more or less
(depending upon the direction of rotation) clutch engagement.
2. If trowel bounces has excessive vibration or does not run
smoothly repeat alignment procedure.
Changing a Blade
Whiteman recommends that all the blades be changed at the
same time.The machine may wobble or bounce if only some of
the blades are changed at one time.
1. Place the machine on a flat, level surface. Adjust the blade
pitch control to make the blades as flat as possible. Note the
blade orientation on the trowel arm.
NOTE
Before removing the blades, please note
the orientation of the blade on the trowel
arm.
1. Remove the three bolts and lock washers that secure the
blade to the trowel arm. Remove the blade.
2. Using a wire brush, scrape all concrete particles and foreign
debris from the trowel arm.
3. Install the new trowel blade onto the trowel arm. Make sure
blade is installed correctly, maintaining the proper orientation for direction of rotation.
4. Reinstall the three bolts and lock washers that secure the
blade to the trowel arm. Tighten all three bolts securely.
5. Repeat steps 1-4 for all remaining blades.
Figure 48. Trowel Arm Adjustment Tool
Hand Clutch Disengagement
1. Start the trowel as outlined in the "Initial Start-up" section"
in this manual. Move the throttle lever so that the engine is
running about 1/4 to 1/3 of full speed.
2. Grip the trowel handle firmly and carefully engage the clutch
by squeezing the clutch lever toward the handle with your left
hand. After the trowel is stabilized and you feel comfortable
with its operation, use your right hand to adjust the housing
adjustment nut.
3. Rotating the nut so that it backs out of the lever housing
increases the engagement and also the squeezing force
required to keep it engaged.
Too much squeezing force may cause premature hand
fatigue. Too little squeezing force may cause belt slippage
and premature belt wear. Each operator should experiment
with the adjustment to get the optimum combination of
squeeze force and belt grip.
4. After initial break-in (approximately 8 hours) the above
procedure should be repeated to attain optimum operator
comfort and belt wear.
5. After considerable belt wear, the adjustments mentioned
above may have a little or no effect on clutch engagement. If
this is the case, the belt should be replaced.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 35
B-SERIES TROWEL — TROUBLESHOOTING (TROWEL)
TABLE 6. TROUBLESHOOTING
SYMPTOM
Engine running rough or not at
all.
Safety kill switch not functioning.
If trowel “bounces, rolls
concrete, or makes uneven
swirls in concrete”.
Machine has a perceptible
rolling motion while running.
POSSIBLE PROBLEM
SOLUTION
Kill switch malfunction?
Make sure that the kill switch is ON or replace switch if
necessary.
Fuel?
Look at the fuel system. Make sure there is fuel being supplied to
the engine. Check to ensure that the fuel filter is not clogged.
Ignition?
Check to ensure that the ignition switch has power and is
functioning correctly.
Other problems?
Consult engine manufacturer’s manual.
Loose wire connections?
Check wiring. Replace as necessary.
Bad contacts?
Replace switch.
Blades?
Make cer tain blades are in good condition, not excessively worn.
Finish blades should measure no less than 2" (50mm) from the
blade bar to the trailing edge, combo blades should measure no
less that 3.5" (89mm). Trailing edge of blade should be straight
and parallel to the blade bar.
Spider?
Check that all blades are set at the same pitch angle as
measured at the spider. A field adjustment tool is available for
height adjustment of the trowel arms (see Optional Equipment).
Bent trowel arms?
Check the spider assembly for bent trowel arms. If one of the
arms is even slightly bent, replace it immediately.
Trowel arm bushings?
Check the trowel arm bushings for tightness. This can be done by
moving the trowel arms up and down. If there is more than 1/8"
(3.2 mm) of travel at the tip of the arm, the bushings should be
replaced. All bushings should be replaced at the same time.
Thrust collar?
Check the flatness of the thrust collar by rotating it on the spider.
If it varies by more than 0.02" (0.5 mm) replace the thrust collar.
Thrust collar bushing?
Check the thrust collar by rocking it on the spider. If it can tilt
more than 3/32" (2.4 mm) [as measured at the thrust collar O.D.],
replace the bushing in the thrust collar.
Thrust bearing worn?
Check the thrust bearing to see that it is spinning free. Note:
Thrust cap, replace if necessary.
Main shaft?
The main output shaft of the gearbox assembly should be
checked for straightness. The main shaft must run straight and
cannot be more than 0.003" (0.08 mm) out of round at the spider
attachment point.
Yoke?
Check to make sure that both fingers of the yoke press evenly on
the wear cap. Replace yoke as necessary.
Blade Pitch?
Check to ensure that each blade is adjusted to have the same
pitch as all other blades. Adjust per maintenance section in
manual.
PAGE 36 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — TROUBLESHOOTING (TROWEL)
TABLE 6. TROUBLESHOOTING (CONTINUED)
SYMPTOM
Clutch slipping or sluggish
response to engine speed
change.
POSSIBLE PROBLEM
SOLUTION
Worn V-belts?
Replace V-belt
Dir ty centrifugal clutch?
Disassemble and clean clutch.
Defective or worn out
centrifugal clutch?
Replace entire clutch.
Hand clutch out of adjustment?
Adjust per instructions in maintenance section of this manual.
Worn or fefective hand clutch
par ts?
Replace par ts as necessary.
Worn bearings in gearbox?
Rotate input shaft by hand. If shaft rotates with difficulty, check
the input and output shaft bearings. Replace as necessary.
Worn or broken gears in
gearbox?
Verify that the gearbox shaft rotates when the input shaft is
rotated. Replace both the worm and worm gear as a set.
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 37
B-SERIES TROWEL — TROUBLESHOOTING (ENGINE)
TABLE 7. TROUBLESHOOTING (ENGINE)
SYMPTOM
Difficult to star t, "fuel is available, but no
SPARK at spark plug".
Difficult to star t, "fuel is available, and
SPARK is present at the spark plug".
Difficult to star t, "fuel is available, spark
is present and compression is normal"
Difficult to star t, "fuel is available, spark
is present and compression is low"
POSSIBLE CAUSE
SOLUTION
Spark plug bridging?
Check gap, insulation or
replace spark plug.
Carbon deposit on spark plug?
Clean or replace spark plug.
Shor t circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
Set to proper gap.
ON/OFF switch is shor ted?
Check switch wiring, replace
switch.
Ignition coil defective?
Replace ignition coil.
Improper spark gap, points dir try?
Set correct spark gap and
clean points.
Condenser insulation worn or shor t
circuiting?
Replace condenser.
Spark plug wire broken or shor t circuiting?
R e p l a c e d e fe c t i ve s p a r k p l u g
wiring.
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Water or dust in fuel system?
Flush fuel system.
Air cleaner dir ty?
Clean or replace air cleaner.
Choke Open?
Close Choke.
Suction/exhaust valve stuck or protruded?
Re-seat valves.
Piston ring and/or cylinder worn?
Replace piston rings and or
piston.
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spar k plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Clean or replace fuel tank cap.
Air in fuel line?
Bleed fuel line.
No fuel present inside priming bulb.
PAGE 38 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
NOTE PAGE
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 39
B-SERIES TROWEL — EXPLANATION OF CODES IN REMARKS COLUMN
The following section explains the different symbols and
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice. Multiquip
does not guarantee the availability of the parts listed.
SAMPLE PARTS LIST
NO.
1
2%
2%
3
4
PART NO. PART NAME
QTY. REMARKS
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
12347
WASHER, 3/8 IN....1 .....MQ-45T ONLY
12348
HOSE ..................A/R ...MAKE LOCALLY
12349
BEARING ..............1 .....S/N 2345B AND ABOVE
NO. Column
QTY. Column
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
Unique Symbols — All items with same unique
symbol
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items. Examples include battery cables, shims,
and certain washers and nuts.
“Not Sold Separately” — Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
PAGE 40 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — SUGGESTED SPARE PARTS
B-SERIES TROWEL 1 TO 3 UNITS WITH HONDA
GX240K1 ENGINE.
1 to 3 Units
Qty. ........ P/N .............................. Description
3 ............ 0189 ...................... GRIP
2 ............ 1103 ...................... SAFETY SWITCH
2 ............ 1727 ...................... QUICK PITCH SAFETY SWITCH
1 ............ 1115 ...................... CABLE STANDARD HANDLE
1 ............ 1714 ...................... CABLE QUICK PITCH
1 ............ 0302 ...................... THROTTLE CABLE
4 ............ 1157 A .................. BUSHING
1 ............ 2828 ...................... ARM (11-3/4")
4 ............ 1162 A .................. LUBE CAP
4 ............ 1167 A .................. SCREW
4 ............ 1456 ...................... NUT
4 ............ 1875 ...................... WASHER
4 ............ 1322 ...................... SCREW
1 ............ 2614 ...................... GASKET KIT
1 ............ 2616 ...................... BEARING KIT
4 ............ 1247 ...................... RUBBER GROMMET
4 ............ 1245 ...................... SPACER
1 ............ 2827 ...................... ARM (16-1/2")
2 ............ 0261 ...................... BELT (A-31) HONDA
1 ............ 10968 .................... THRUST COLLAR KIT
2 ............ 9807955846 .......... SPARK PLUG HONDA
2 ............ 17620ZH7023 ....... TANK CAP (HONDA)
2 ............ 17210ZE2505 ....... AIR CLEANER ELEMENT (HONDA)
2 ............ 17218ZE2505 ....... FILTER OUTER (HONDA)
B-SERIES TROWEL 1 TO 3 UNITS WITH ROBIN
EH25-2 ENGINE.
1 to 3 Units
Qty. ........ P/N .............................. Description
3 ............ 0189 ...................... GRIP
2 ............ 1103 ...................... SAFETY SWITCH
2 ............ 1727 ...................... QUICK PITCH SAFETY SWITCH
1 ............ 1115 ...................... CABLE STANDARD HANDLE
1 ............ 1714 ...................... CABLE QUICK PITCH
1 ............ 0302 ...................... THROTTLE CABLE
4 ............ 1157 A .................. BUSHING
1 ............ 2828 ...................... ARM (11-3/4")
4 ............ 1162 A .................. LUBE CAP
4 ............ 1167 A .................. SCREW
4 ............ 1456 ...................... NUT
4 ............ 1875 ...................... WASHER
4 ............ 1322 ...................... SCREW
1 ............ 2614 ...................... GASKET KIT
1 ............ 2616 ...................... BEARING KIT
4 ............ 1247 ...................... RUBBER GROMMET
4 ............ 1245 ...................... SPACER
1 ............ 2827 ...................... ARM (16-1/2")
2 ............ 0152 1 ................... BELT (A-30) (ROBIN)
1 ............ 10968 .................... THRUST COLLAR KIT
2 ............ 0650140031 .......... SPARK PLUG (ROBIN)
2 ............ 0430430015 .......... TANK CAP (ROBIN)
2 ............ 2703261008 .......... AIR CLEANER ELEMENT (ROBIN)
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 41
B-SERIES TROWEL — NAMEPLATE AND DECALS
PAGE 42 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO.
1
2
3
4
5
6
7
8
9
*
10
*
11
*
12
13
14
*
15
*
PART NO.
1734
1755
12405
1758
1499
1735
1492
1261
11247
11246
11246
1940
11246
11246
12620
PART NAME
QTY. REMARKS
DECAL: WARNING DO NOT OPERATE
1
DECAL: WARNING PITCH HANDLE
1
DECAL: QUICK PITCH™ HANDLE INSERT
2
2
DECAL: QUICK PITCH™ HANDLE
DECAL: MQ WHITEMAN (LARGE)
1
DECAL: PRE-LOAD INDICATOR
1
DECAL: STANDARD HANDLE (FINISHER)
1
DECAL: DO NOT LIFT
1
DECAL: HELMET, FOOT AND GLOVE
1
DECAL: HEAT
1
DECAL: OIL CHECK
1
NAMEPLATE .......................................................... 1 ....... CONTACT MULTIQUIP PARTS DEPT.
DECAL: MQ WHITEMAN (SMALL)
1
DECAL: GEAR DRIVE
1
DECAL: BELT DRIVE
1
KIT, DECAL REPLACEMENT ................................ 1 ....... INCLUDES ITEMS W/
*
SEE DECAL ILLUSTRATIONS ON PAGE 12
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 43
B-SERIES TROWEL — STANDARD HANDLE
STANDARD HANDLE
PAGE 44 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — STANDARD HANDLE
STANDARD HANDLE
NO.
PART NO.
PART NAME
1
1
2
3
4
5
5
6
7
8
9
10
11
12
13
14
15#
16#
17#
18#
19#
20#
21
22
23#
24
25
26
27
28
29
30
31
32
33
34
35
36
0189
4634
1102
0304
1103
1101
1907
HANDLE GRIP
2
HANDLE GRIP (ELECTRIC MODEL)
2
PLUG
1
RHMS 10-24X 1/4"
4
SAFETY SWITCH ASSY
1
HANDLE ONLY
1
HANDLE ONLY (ELECT. MODEL)
1
HANDLE ASSY ................................................. 1 ............. CONTACT UNIT SALES DEPT./ ACCESSORY ITEM
LOCK NUT 3/8-16
2
FLAT WASHER 3/8"
4
SUPPORT BLOCK ASSY (PULLEY & PIN)
1
HOLDER
1
HHCS 3/8-16X2.3/4"
2
MQ-WHITEMAN DECAL
2
2.1/2" CHROME DECAL
1
THROTTLE CONTROL ASSY
1
SHSS 3/8-16X3/8"
1
HAND WHEEL
1
TROWEL CONTROL SHAFT
1
BEARING
1
BEARING
1
SET COLLAR (WITH SET SCREW)
1
SLIDE BLOCK .................................................. 1 ............. SLIDE BLOCK ONLY
CONTROL CABLE ASSY ................................. 1 ............. 47.25 INCHES LONG
BCHS 1/4-20X3/8" NY-LOC
2
SPACER
1
ROLL PIN 5/32 X1.3/8"
2
BRASS JAM NUT 5/16-18
2
YOKE ARM
1
ARM PIN
1
COTTER PIN 3/32X3/4"
2
PIGTAIL ASSY (ELECT. MODEL)
1
SWITCH BOX (ELECT. MODEL)
1
FHMS 10-32X3/4" (ELECT. MODEL)
1
MICRO SWITCH (ELECT. MODEL)
1
SWITCH CONDUIT ASSY (ELECT. MODEL) ... 1 ............. INCLS. ITEMS W/
LIFT HANDLE ASSY ........................................ 1 ............. NO LONGER AVAILABLE
TROWEL CONTROL ASSY .............................. 1 ............. INCLS. ITEMS W/#
*
*
*
*
10133
10136
1117
0190A
1121
1499
1492
0302
0185
0280B
1478
0281
1111
3615
1113
1115
0786
0786A
1114
1116
1150
1151
0683
2505
01751
5044A
1268
1189
1110
QTY.
REMARKS
*
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 45
B-SERIES TROWEL — QUICK PITCH™ HANDLE
QUICK PITCH ™ T-HANDLE
PAGE 46 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — QUICK PITCH™ HANDLE
QUICK PITCH ™ T-HANDLE
NO.
PART NO.
PART NAME
1
2
3
3%
3%
4
5
6
7
8
9
10
11
12 #
13 #
14 #
15 #
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
1746
1724
1707
1739
1734
1729
1706
1745
QUICK PITCH TRIGGER
1
CONTROL HANDLE GRIP
2
CONTROL HANDLE .................................. 1 ............. INCLUDES ITEMS W/%
BUSHING
2
WARNING DECAL
1
ROLL PIN 3/16X1.1/4"
3
LATCH RETURN SPRING
1
LATCHING SHAFT
1
HANDLE ASSY COMPLETE ...................... 1 ............. CONTACT UNIT SALES DEPT./ACCESSORY ITEM
FINISHER HANDLE PATENT DECAL
1
WHITEMAN DECAL
2
HANDLE ONLY
1
PRE-LOAD DECAL
1
LOCK NUT 3/8-16
2
FLAT WASHER 3/8"
4
HOLDER
1
HHCS 3/8-16X2.3/4"
2
SUPPORT BLOCK ASSY
1
SNAP RING
1
HARDENED WASHER 1/2"X1/32"
2
PRE-LOAD ADJUSTMENT NUT
1
PRE-LOAD ADJUSTMENT PIN
1
PRE-LOAD ADJUSTMENT SCREW
1
PIVOT PLATE BUSHING
2
CONTROL SHAFT
1
ROLL PIN 3/16"X1"
1
ROLL PIN 1/4"X3/4"
1
SLIDE CONTROL ARM
1
PHSTS 1/4X1/2"
1
SAFETY SWITCH ASSY
1
HANDLE PAD & COVER
1
RHMS 10-24X1/4"
2
THROTTLE CABLE ASSY
1
HANDLE GRIP
2
BRASS JAM NUT 5/16-18
2
YOKE ARM
1
YOKE PIN
1
COTTER PIN 3/32"X3/4"
2
PRE-LOAD ADJUSTMENT BLOCK
1
CONTROL BALANCE SPRING
1
CONTROL CABLE ASSY
1
ROLL PIN 3/16"X1.3/8"
1
ROLL PIN 1/4"X1.3/8"
1
CONTROL CABLE SLIDE BLOCK
1
CONTROL ARM CONNECTOR
1
LIFT HANDLE ASSY .................................. 1 ............. NO LONGER AVAILABLE
TOOL ASSY FOR UNLOADING SPRING ... 1 ............. CONTACT UNIT SALES DEPT./ACCESSORY ITEM
T-HANDLE ASSY ....................................... 1 ............. INCLUDES ITEMS W/
KIT HANDLE HARDWARE ......................... 1 ............. INCLUDES ITEMS W/ #
*
*
*
*
*
*
1758
1499
1701
1735
10133
10136
0190A
1121
1117
1737
1733
1718
1732
1717
1719
1711
4568
1731
1708
1743
1727
1730
0304
0302
0189
1116
1150
1151
0683
1716
1715
1714
1757
1726
1712
1709
1754
2811
QTY.
REMARKS
*
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 47
B-SERIES TROWEL — THRUST BEARING KIT ASSY.
THRUST BEARING KIT ASSEMBLY.
PAGE 48 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — THRUST BEARING KIT ASSY.
THRUST BEARING KIT ASSEMBLY.
NO.
1
*
2
*
3
*
4
*
5
*
6
PART NO.
12208
12778
10793
1471
1154A
10968
PART NAME
QTY.
REMARKS
WEAR RING
1
FLANGE BEARING
1
THRUST COLLAR W/BUSHING
1
BUSHING
1
LOWER WEAR PLATE
1
THRUST BEARING KIT .................................................... 1............ INCLUDES ITEMS W/
*
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 49
B-SERIES TROWEL — 3 AND 4-BLADE SPIDER ASSY.
3 AND 4 BLADE SPIDER ASSY.
PAGE 50 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — 3 AND 4-BLADE SPIDER ASSY.
3 AND 4 BLADE SPIDER ASSY.
NO.
1
*
2
*
3
*
4
*
5%$■+
6%$■+
7%$■+
8%$■+
9%$■+
10%$■+
11%+
12%$
12■+
13%$■+
14%$■+
15%$■+
16$■
17%$■+
18%$■+
19%$■+
20%$■+
21
21
21
21
22%$■+
23
24 #
*
PART NO.
12208
12778
10793
1154A
1157A
0164B
1875
1876
0105
0161C
1156
2827
2828
1163
4164
1316
1161
1322
1456
1167A
0166A
1489
1155
1490
1160
1162A
10968
1471
PART NAME
QTY.
REMARKS
WEAR RING
1
FLANGE BEARING
1
THRUST COLLAR ................................................................ 1 ........ INCLUDES ITEMS W/#
WEAR PLATE
1
BEARING INSERT
3,4
RADIUS HEAD 3/8- 16 x 1-1/4”
3,4
INT. SHKP. WASHER 3/8”
3,4
JAM NUT 3/8- 16
3,4
HHCS 5/16- 18 x 1-1/2”
6,8
LOCK WASHER 5/16”
6,8
SPIDER PLATE ONLY ......................................................... 1 ........ 3 BLADE ONLY
TROWEL ARM EXTENDED, 16-1/2" (LONG)
3,4
TROWEL ARM 11-3/4 (SHORT)
3,4
TROWEL ARM LEVER
3,4
ROLL PIN 5/16 x 1-3/4”
3,4
SPRING (RIGHT HAND)
3,4
SPIDER PLATE ONLY ......................................................... 1 ........ 4 BLADE ONLY
RETAINING SCREW ASSY.
3,4
HEX NUT 3/8-16
1
SHSS 3/8-16 x 1-1/2” CONE POINT
1
LOCK WASHER 3/8”
3,4
SPIDER PLATE ASSY. (3 BLADE/W 16-1/2 ARM) .............. 1 ........ INCLUDES ITEMS W/%
SPIDER PLATE ASSY. (3 BLADE/W 11-3/4 ARM) .............. 1 ........ INCLUDES ITEMS W/+
SPIDER PLATE ASSY. (4 BLADE/W 16-1/2 ARM) .............. 1 ........ INCLUDES ITEMS W/$
SPIDER PLATE ASSY. (4 BLADE/W 11-3/4 ARM) .............. 1 ........ INCLUDES ITEMS W/■
LUBRA- CAP
3,4
THRUST BEARING KIT
1
INCLUDES ITEMS W/
*
THRUST COLLAR BUSHING
1
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 51
B-SERIES TROWEL — GEARBOX AND ENGINE MOUNTS ASSY.
GEARBOX AND ENGINE MOUNTS ASSY.
GEARBOX REQUIRES
22 OZ. OF LUBRICATING
OIL FOR OPERATION.
2
GEARBOX
LUBRICATING
OIL
QTY. 1
22 0Z.
1
4
39
38
35
BEARING
KIT
NOTES:
USE SPECIALLY FORMULATED
1 WHITEMAN GEARBOX LUBRICANT
P/N 10139 OR ISO 680 OIL.
SEE GUARD RING ASSY., PAGE 60,
2 ITEM 1.
PAGE 52 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — GEARBOX AND ENGINE MOUNTS ASSY.
GEARBOX AND ENGINE MOUNTS ASSY.
NO.
PART NO.
PART NAME
1%
2%
3%
4
5#%
6%
7#%
8%
9 %
10
11%
12%
13
14
15#%
16#%
17%
18%
19%
20%
21%
22 %
23%
24%
25 %
26
27%
28%
29
30
30
31
32
33
34
35
36
36
36
36
37
37
37
38
39
1131
0131A
1136
2614
0735A
1132
0735
1851
2308
0627
0753
1133
0655
0300B
0232A
0232
1138
1140
2440
1810
1145
0254
1146
10235
1143
1238
1139
0121A
1481
1480
0166A
1245
1247
2273
1816
1130
1955
1965
1958
1956
1943
1964
1961
2616
10139
GEAR CASE
1
HHCS 1/4-20X3/4"
8
END CAP
1
GASKET KIT ............................................... 1 ............. INCLS. ITEMS W/
BEARING CUP
2
AIR VENT
1
BEARING CONE
2
WORM & COUNTER SHAFT
1
O-RING
2
SQ. KEY 3/16X3/16X1.1/4"
1
OIL SEAL
1
FLANGE
1
HHCS 5/16-18X3/4 ASSY
1
FLAT WASHER 5/16" ASSY
1
BEARING CUP
2
BEARING CONE
2
RETAINING RING
1
BRONZE GEAR 1 1/8 38 TEETH
1
MAINSHAFT
1
WEIGHT
2
COVER PLATE
1
OIL SEAL
1
FHSCS 5/16-18X1"
4
EXT. SHKP. WASHER 5/16"
4
SEAL RING
1
WOODRUFF KEY#25 ASSY
1
WOODRUFF KEY#21
1
SQUARE HEAD PIPE PLUG 3/8"
1
FHCS 3/8-16X1.3/4" (ELECTRIC)
4
C’SINK SHKP WASHER 3/8"
4
LOCK WASHER 3/8" (ELECTRIC)
4
SPACER
4
GROMMET (STATIONARY RING ONLY) 4
STATIONARY GUARD RING ...................... 1 ............. REPLACES 1244
PLATE
2
GEARBOX ASSY ........................................ 1 ............. INCLS. ITEMS W/%
FRONT ENGINE MOUNT (ELECTRIC)
1
FRONT ENGINE MOUNT (ROBIN 7.5 H.P.)1
FRONT ENGINE MOUNT (HONDA 8 H.P.) 1
FRONT ENGINE MOUNT (B & S 8H.P.)
1
REAR ENGINE MOUNT (ELECTRIC)
1
REAR ENGINE MOUNT (ROBIN & HONDA1
REAR ENGINE MOUNT (B & S 8 H.P.)
1
BEARING REPLACEMENT KIT .................. 1 ............. INCLS ALL ITEMS W/#
GEAR BOX OIL (22 OZ.)
*
*
*
QTY.
REMARKS
*
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 53
B-SERIES TROWEL — ENGINES, 8.0 HP HONDA, 8.5 HP ROBIN, & 5 HPB&S
ENGINES, 8.0 HP HONDA, 8.5 HP ROBIN, & 8.0 HP BRIGGS AND STRATTON
PAGE 54 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — ENGINES, 8.0 HP HONDA, 8.5 HP ROBIN, & 5 HPB&S
ENGINES, 8.0 HP HONDA, 8.5 HP ROBIN, & 8.0 HP BRIGGS AND STRATTON
NO.
PART NO.
PART NAME
1
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
28
30
23
24
26
26
27
28
30
1256
GX240K1QA2
1242
0310
0250
0252
0251
0458
B1766
0855
0253
1868
0456
0261
1127
1335
0181B
2577
0300B
0161C
10181
1391
ENGINE 8.5HP ROBIN
1
ENGINE 8HP HONDA
1
ENGINE 8HP BRIGS & STRATTON
1
SQUARE KEY 1/4X1/4X1.1/2"
1
AUTOMATIC CLUTCH ASM 1" BORE ........ 1 ............. INCLS. ALL ITEMS W/
SPINDLE 1" BORE
1
CLUTCH HOUSING DRUM
1
CLUTCH HOUSING DRUM BUSHING
1
WEIGHT, CLUTCH ..................................... 1 ............. REPLACES P/N 0454
SPRING
1
CLUTCH EXPANSION PLATE
1
SCREW, SHS 3/8-24 X 3/4, NOPLT ............ 1 ............. REPLACES P/N 0457
BELT RUNNER (BEARING)
1
BELT (A31)(HONDA,B&S)
1
PULLEY
1
BELT GUARD
1
LOCK WASHER 1/4"
2
T-BOLT 1/4-20
2
FLAT WASHER 5/16"
4
LOCK WASHER 5/16"
4
HHCS 5/16-24 x 1-1/4"
4
HHCS 5/16-24 x 1-1/2"
4
LIFT STRAP ............................................... 1 ............. CONTACT UNIT SALES DEPT./ACCESSORY ITEM
BELT (A30) GATES (ROBIN)
1
THROTTLE BRACKET(ROBIN)
1
HHCS 5/16-24 x 1"
4
LOCK WASHER 5/16"
4
HHCS 3/8-16 x 1"
3
FHSCS 3/8-16 x 1"
1
LOCK WASHER 3/8"
3
BELT (A30)(ROBIN)
1
THROTTLE BRACKET(ROBIN)
1
*
*
*
*
*
*
*
*
0152 1
2743
10229
0161C
0205
1394
0166A
1521
2743
QTY.
REMARKS
*
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 55
B-SERIES TROWEL — HAND CLUTCH ASSY. (S/N LJ41888 AND BELOW)
HAND CLUTCH ASSY. - S/N LJ41888 AND BELOW
PAGE 56 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — HAND CLUTCH ASSY. (S/N LJ41888 AND BELOW)
HAND CLUTCH ASSY. - S/N LJ41888 AND BELOW
NO.
PART NO.
PART NAME
1
1
2
3
4
5
6
7
8
9
10
11
11
12
13
13
14
15
16
16
17
17
18
19
19
20
20
21
22
23
GX24OK1QA2
1256
2834
1512
10075
ENGINE 8HP HONDA
1
ENGINE 8.5HP ROBIN
1
SPACER (ROBIN)
1
HAND CLUTCH HAND LEVER
1
HAND CLUTCH CABLE ASSY
1
LIFTING BALE ASSY .................................. 1 ............. CONTACT UNIT SALES DEPT./ACCESSORY ITEM
COTTER PIN 1/16"X1/2"
2
CLEVIS PIN 1/4"X7/8"
2
LOCK NUT 3/8-24
2
HHCS 3/8-24X2.1/4"
2
HAND CLUTCH 1" BORE
1
LIFT BRACKET PLATE (HONDA)
1
LIFT BRACKET PLATE (ROBIN)
1
CLUTCH ARM
1
PULLEY (HONDA)
1
PULLEY (ROBIN)
1
LOCK WASHER 1/4"
4
HHCS 1/4-20X5/8"
4
BELT GUARD MOUNT (HONDA)
1
BELT GUARD MOUNT (ROBIN)
1
BELT (A30)(HONDA)
1
BELT (A30)(ROBIN)
1
BELT GUARD
1
HHCS 3/8-16X1" (ROBIN)
4
HHCS M8-1.25X25MM (HONDA)
4
LOCK WASHER 3/8" (ROBIN)
4
LOCK WASHER 5/16" (HONDA)
4
SPACER (ROBIN)
4
SHSS 10-32X1/4"
1
GRIP
5117
5133
1063
0478
2806
10076
10137
10089
0740
2842
0181B
4514
2861
2862
1521
0260
2492
0205
1605
0166A
0161C
1897
10450
2267
QTY.
REMARKS
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 57
B-SERIES TROWEL — HAND CLUTCH ASSY. (S/N LJ41889 AND ABOVE)
PAGE 58 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — HAND CLUTCH ASSY. (S/N LJ41889 AND ABOVE)
HAND CLUTCH ASSY — S/N LJ41889 AND ABOVE
NO.
PART NO.
PART NAME
QTY.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
17
18
18
19
20
21
22
23
24
25
26
GX24OK1QA2
1256
10036
6014C
0300B
1391
10450
0948
0181B
1579
10936
10971
2469
1512
10831
10833
0730
0262
0261
1127
2842
10229
0161C
10898
9154
10935
10740
1876
10822
ENGINE 8HP HONDA
ENGINE 8.5HP ROBIN
CLUTCH ASSIST HANDLE ASSY
HEX FINISH NUT 5/16-24
FLAT WASHER 5/16”
HHCS 5/16-24X1.1/2”
SHSS 10-32X1/4”
FLAT WASHER 1/4"
LOCK WASHER 1/4”
HHCS 1/4-20 x 1/2”
HAND CLUTCH CABLE ASSY
SHOULDER BOLT 5/16X1.1/2”
PULLEY,ENGINE
HAND CLUTCH CONTROL LEVER
BELT GUARD MOUNT
BELT GUARD
HHCS 1/4-20X1”
BELT,(A33)(HONDA)
BELT,(A31)(ROBIN)
PULLEY,DRIVEN(HONDA)
PULLEY,DRIVEN(ROBIN)
HHCS 5/16-24X1”
LOCK WASHER 5/16”
CLUTCH BRKT.
HHCS 3/5-16X1.3/4”
PULLEY,IDLER
BELT TENSIONING SHOE
HEX JAM NUT 3/8-16
CLUTCH IDLER LEVER
1
1
1
1
5
1
1
1
6
2
1
1
1
1
1
1
4
1
1
1
1
2
2
1
1
1
1
1
1
REMARKS
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 59
B-SERIES TROWEL — ELECTRIC MOTOR ASSY.
ELECTRIC MOTOR ASSY.
PAGE 60 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — ELECTRIC MOTOR ASSY.
ELECTRIC MOTOR ASSY.
NO.
PART NO.
PART NAME
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1860
0627
1231
1232
0251
0458
0454
0855
0253
0457
0456
1867
1335
2577
0181B
1127
0152 3
0400B
0300B
0161C
ELECTRIC MOTOR 2HP
1
SQUARE KEY 3/16X3/16X1.1/4"
1
AUTOMATIC CLUTCH ASM 5/8" BORE
1
SPINDLE 5/8" BORE
1
DRUM, CLUTCH HOUSING ...................... 1 ............. INCLS. ITEMS W/
BUSHING, CLUTCH HOUSING DRUM
1
WEIGHT SET (INCLUDES 4 WEIGHTS) 1
SPRING
1
CLUTCH EXPANSION PLATE
1
HSSS 3/8-24X1/2"
1
BELT RUNNER (BEARING)
1
PLUG
1
BELT GUARD
1
T-BOLT 1/4-20
2
LOCK WASHER 1/4"
2
PULLEY
1
BELT (A28)
1
HHCS 5/16-18X1/2"
4
FLAT WASHER 5/16"
4
LOCK WASHER 5/16"
4
*
QTY.
REMARKS
*
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 61
B-SERIES TROWEL — GUARD RING ASSY.
GUARD RING ASSY.
PAGE 62 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — GUARD RING ASSY.
GUARD RING ASSY.
NO.
PART NO.
PART NAME
1
2
2
2273
1489
1490
STATIONARY GUARD RING ............................................... 1 ............ REPLACES P/N 1244
SPIDER PLATE ASSY 16-1/2" ARM (EXT) .......................... 1 ............ 3-BLADE MODEL
SPIDER PLATE ASSY 16-1/2" ARM (EXT) .......................... 1 ............ 4-BLADE MODEL
QTY.
REMARKS
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 63
B-SERIES TROWEL — STABILIZER RING ASSY.
STABILIZER RING ASSY
PAGE 64 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — STABILIZER RING ASSY.
STABILIZER RING ASSY
NO
PART NO
PART NAME
1
2
3
4
5
5
0161C
1237
1723
6014C
1482
1483
QTY.
REMARKS
WASHER, LOCK, 5/16 MED
4
SCREW, SCH 5/16-18 X 7/8, NYL, NP
4
ROD END, 5/16-24 MALE
4
NUT, HEX FINISH 5/16-24
8
RING, STABILIZER, 14-1/2" ARM .............. 1 ............. 3-BLADE MODEL, REPLACES P/N 1234
RING, STABILIZER, 14-1/2" ARM .............. 1 ............. 4-BLADE MODEL, REPLACES P/N 1235
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 65
B-SERIES TROWEL — BLADES & ADJUSTMENT FIXTURE ASSY.
(OPTIONS)
BLADES & ADJUSTMENT FIXTURE ASSY.
PAGE 66 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — BLADES & ADJUSTMENT FIXTURE ASSY.
BLADES & ADJUSTMENT FIXTURE ASSY.
NO.
PART NO.
PART NAME
20
20
21
22
22
23
24
26
31
32
33
34
35
36
39
39
40
40
41
42
46
47
49
50
0202
0201
1434
0490
0487
0489
0488
QTY. REMARKS
COMBO FLOAT & FINISH BLADE .......................... 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
ENDURO COMBO FLOAT &FINISH BLADE .......... 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
FLOAT BLADE ........................................................ 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
FINISH BLADE ....................................................... 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
ENDURO FINISH BLADE W/ROTATING ................ 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
HHCS 5/16-18X1" RING
3,4
GUARD RING LUG RING
3,4
TROWEL LUG (FINISH BLADE ONLY)
3,4
SHCS 7/16-14X1"
3
SHCS 3/8-16X1/2"
20
GRINDING DISC HUB
1
STONE MOUNT PLATE
1
GRINDING DISC STONE ONLY ............................. 1 ......... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
GRINDING DISC ASSY .......................................... 1 ......... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
UNIVERSAL COMBO BLADE ................................. 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
ENDURO UNIVERSAL COMBO BLADE ................ 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
UNIVERSAL FINISH BLADE .................................. 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
ENDURO UNIVERSAL FINISH BLADE .................. 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
UNIVERSAL MOUNTING BAR ............................... 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
SNAP PIN 1/4"X1.3/4" ............................................ 6,8 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
TROWEL ARM ADJ. FIXTURE ASSY ..................... 1 ......... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
REVERSIBLE COMBO BLADE ............................... 3,4 ...... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
FLOAT DISC ........................................................... 1 ......... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
FLOAT DISC LATCH PIN ....................................... 4 ......... CONTACT UNIT SALES DEPT./ACCESSORY ITEM
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 67
B-SERIES TROWEL — LIFTING BALE ASSY. (OPTION)
LIFTING BALE ASSY. (OPTION)
PAGE 68 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
B-SERIES TROWEL — LIFTING BALE ASSY. (OPTION)
LIFTING BALE ASSY. (OPTION)
NO.
PART NO.
PART NAME
1
2
3
4
5
7
8
10229
0161C
0205
0166A
1897
QTY.
REMARKS
LIFTING BALE ASSY .................................. 1 ............. CONTACT UNIT SALES DEPT./ACCESSORY ITEM
HHCS 5/16-24X1"
4
LOCK WASHER 5/16"
4
LIFTING BALE ASSY .................................. 1 ............. CONTACT UNIT SALES DEPT. /ACCESSORY ITEM
HHCS 3/8-16X1"
3
LOCK WASHER 3/8"
3
SPACER (ROBIN ENGINE)
4
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 69
HONDA GX-240K1 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 70 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
3
*
5
6
8#
9#
10
12
13
14
15
PART NO.
16271ZE2000
17210ZE2505
17218ZE2505
17231ZH9820
17232891000
17238ZE2310
17239ZE1000
17410ZE2020
90203ZA0800
90325044000
90009ZE2003
9405006000
PART NAME
QTY.
REMARKS
GASKET, ELBOW ..................................... 1 ............. INCLUDES ITEM W/
*
ELEMENT, AIR CLEANER, DUAL
1
FILTER, OUTER
1
COVER, AIR CLEANER
1
GROMMET, AIR CLEANER
1
COLLAR, AIR CLEANER
2
COLLAR B, AIR CLEANER
1
ELBOW COMP., AIR CLEANER ............... 1 ............. INCLUDES ITEM W/#
WINGNUT 6MM
1
WINGNUT, TOOL BOX SETTING
2
BOLT- WASHER 6 X 22
1
NUT, FLANGE 6MM
2
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 71
HONDA GX-240K1 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 72 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
1
1
2
3
4
5
6
*
7
8
9
10
11
12
13
14
15
PART NO.
14100ZE2W00
14100ZE2W01
14100ZE2306
14410ZE2013
14431ZE2010
14441ZE2000
14451ZE1013
14568ZE1000
14711ZE2000
14721ZE2000
14751ZE2003
14771ZE2000
14773ZE2000
14781ZE2000
14791ZE2010
90012ZE0010
90206ZE1000
PART NAME
QTY.
REMARKS
CAMSHAFT ASSY. ................................... 1 ............. INCLUDES ITEM W/
*
CAMSHAFT ASSY.
1
CAMSHAFT
1
ROD PUSH
2
ARM VALVE ROCKER
2
LIFTER VALVE
2
PIVOT ROCKER ARM
2
SPRING, WEIGHT RETURN
1
VALVE, IN.
1
VALVE, EX.
1
SPRING, VALVE
2
RETAINER, IN. VALVE SPRING
1
RETAINER, EX. VALVE SPRING
1
ROTATOR, VALVE
1
PLATE, PUSH ROD GUIDE
1
BOLT, PIVOT 8MM
2
NUT, PIVOT ADJ.
2
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 73
HONDA GX-240K1 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 74 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
1 +%
*
2
*
3
*
4
*
4
5
*
6 +%
*
7 +%
*
8
*
9
*
10
*
11
*
12
*
13
*
14
15
16
17
18
19
*
19
*
19
20
21
*
22
*
23
*
24
*
25
26
26
26
*
27
*
28
*
PART NO.
16010ZE2812
16011ZA0931
16013ZA0931
16015ZE2005
16015ZE8005
16016ZHW01
16024ZE1811
16028ZE0005
16028ZE2005
16100ZE2W71
16124ZE0005
16166ZE2W70
16172ZE3W10
16173001004
16211ZE2000
16220ZA0702
16221ZA0800
16223ZA0800
16610ZE1000
16953ZE1406
16953ZE1811
16953ZE1812
16954ZE1811
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
9430520122
99101ZH70820
99101ZH70850
99101ZH70880
99204ZE20400
16015ZE8005
PART NAME
QTY. REMARKS
GASKET SET
1
VALVE SET, FLOAT
1
FLOAT SET
1
CHAMBER SET, FLOAT ................ 1 ..... INCLUDES ITEMS W/%, BELOW S/N BE70BA
CHAMBER SET, FLOAT ................ 1 ..... ABOVE S/N BE70BA
SCREW SET
1
SCREW SET, DRAIN
1
SCREW SET B
1
CHOKE SET
1
CARBURETOR ASSY. ................... 1 ..... INCLUDES ITEMS W/
*
SCREW, THROTTLE STOP
1
NOZZLE, MAIN
1
COLLAR, SET
1
O-RING
1
INSULATOR, CARB.
1
SPACER COMP., CARB.
1
GASKET, CARBURETOR
1
GASKET, INSULATOR
1
LEVER COMP., CHOKE, STD.
1
LEVER, VALVE ............................. 1 ..... BELOW S/N BE70BA
LEVER, VALVE ............................. 1 ..... ABOVE S/N BE70BA
LEVER, VALVE
1
PLATE, LEVER SETTING
1
SPRING, VALVE LEVER
1
GASKET, VALVE
1
CUP, FUEL STRAINER
1
SCREW, PAN 3 X 6
2
PIN, SPRING 2 X 12
1
JET, MAIN #82, OPTIONAL
1
JET, MAIN #85, OPTIONAL
1
JET, MAIN #88
1
JET SET, PILOT #40
CHAMBER SET, FLOAT ................ 1 ..... INCLUDES ITEMS W/+
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 75
HONDA GX-240K1 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 76 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
2
3
4
5
8
10
*
11
*
12
*
13
*
14
*
15
*
16
*
17
*
19
20
21
*
24
*
26
*
27
PART NO.
16551ZE2000
16555ZE2000
16561ZE2000
16562ZE2000
16570ZE2W20
16571ZE2W00
16574ZE1000
16575ZE2W00
16576891000
16578ZE1000
16581ZE2W00
16584883300
16592883310
90013883000
90015ZE5010
90114SA0000
93500050280A
93500050160A
9405006000
PART NAME
QTY.
REMARKS
ARM, GOVERNOR
1
ROD, GOVERNOR
1
SPRING, GOVERNOR
1
SPRING, THROTTLE RETURN
1
CONTROL ASSY., REMOTE ..................... 1 ............. INCLUDES ITEM W/
*
LEVER, CONTROL
1
SPRING, LEVER
1
WASHER, CONTROL LEVER
1
HOLDER, CABLE
1
SPACER, CONTROL LEVER
1
BASE COMP., CONTROL
1
SPRING, CONTROL ADJUSTING
1
SPRING, CABLE RETURN
1
BOLT, FLANGE 6 X 12 CT200
2
BOLT, GOVERNOR ARM
1
NUT, SELF-LOCK 6MM
1
SCREW, PAN 5 X 28
1
SCREW, PAN 5 X 16
1
NUT, FLANGE 6MM
1
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 77
HONDA GX-240K1 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 78 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
2
3
4
5
6
7+
8#
9%
10
11 ■
*
12 ■
*
13 ■
*
14
*
15
*
16
*
17
18
*
19
*
20
21
*
22
*
PART NO.
11400ZE2601
11381ZE2800
15600ZG4003
15600735003
15620ZG4910
15621896010
15625ZE1000
15625ZE1003
16510ZE2811
16511ZE2000
16512ZE2811
16513ZE2000
16531ZE2000
90473147000
90602ZE1000
90701HC4000
91201890003
9410106800
957010803500
961006202000
961006206000
PART NAME
QTY.
REMARKS
COVER ASSY., CRANKCASE .................. 1 ............. INCLUDES ITEMS W/
*
GASKET, CASE COVER
1
CAP ASSY., OIL FILLER .......................... 1 ............. INCLUDES ITEM W/%
CAP ASSY., OIL FILLER .......................... 1 ............. INCLUDES ITEM W/#
CAP, OIL FILLER ...................................... 1 ............. INCLUDES ITEM W/+
GASKET, OIL FILLER CAP
1
GASKET, OIL FILLER CAP
1
GASKET, OIL FILLER CAP
1
GOVERNOR ASSY., BALANCER ............. 1 ............. INCLUDES ITEMS W/■
WEIGHT, GOVERNOR
2
HOLDER, GOVERNOR WEIGHT
1
PIN, GOVERNOR WEIGHT
2
SLIDER, GOVERNOR
1
WASHER 6 X 16
1
CLIP, GOVERNOR HOLDER
1
PIN, DOWEL 8 X 12
2
OIL SEAL 30 X 46 X 8
1
WASHER, PLAIN 6MM
1
BOLT, FLANGE 8 X 35
7
BEARING, RADIAL BALL 6202
1
BEARING, RADIAL BALL 6206
1
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 79
HONDA GX-240K1 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 80 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
2
8
10
12
*
PART NO.
13320ZE2601
13351ZE2010
90745ZE2600
961006206000
PART NAME
CRANKSHAFT COMP., Q- TYPE
WEIGHT, BALANCER
KEY 6.3 X 6.3 X 43
BEARING, RADIAL BALL 6206
QTY.
1
1
1
1
REMARKS
INCLUDES ITEM W/
*
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 81
HONDA GX-240K1 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 82 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
1
2
2
2
3
3
4
5
6
7
8
*
9
10
11
12
12
13
14
*
15
16
PART NO.
12000ZE2834
15510ZE2023
15510ZE2033
15510ZE2043
16541ZE2000
16541ZE2010
32197ZE2003
90013883000
90131896650
90446KE1000
91201890003
91353671003
9405010000
9410912000
9425108000
9425110000
957010601200
961006202000
90013883000
34150ZH7003
PART NAME
QTY.
REMARKS
CYLINDER ASSY., BALANCER + OIL ALERT ...... 1 .......... INCLUDES ITEMS W/
*
SWITCH ASSY., OIL LEVEL
1
SWITCH ASSY., OIL LEVEL
1
SWITCH ASSY., OIL LEVEL
1
SHAFT, GOVERNOR ARM
1
SHAFT, GOVERNOR ARM
1
SUB- HARNESS
1
BOLT, FLANGE 6 X12 CT200
1
BOLT, DRAIN PLUG
2
WASHER 8.2 X17X0.8
1
OIL SEAL 30X46X8
1
O-RING 14MM ARAI
1
NUT FLANGE 10MM
1
WASHER, DRAIN PLUG 12MM
2
PIN, LOCK 8MM
1
PIN, LOCK 10MM
1
BOLT, FLANGE 6X12
2
BEARING, RADIAL BALL 6202
1
BOLT, FLANGE 6X12 CT200
1
ALERT UNIT, OIL
1
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 83
HONDA GX-240K1 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 84 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
1
2
*
3
*
4
*
5
6
7
8
10
11
12
13
14
15
16
17
17
PART NO.
12200ZH9000
12204ZE2306
12205ZE2305
12216ZE2300
12251ZE2800
12310ZE2020
12391ZE2020
14775ZE2010
90014ZE2000
90042ZE2000
90047ZE2000
90441ZE2010
9430112200
950051100130M
957011008000
9807956846
9807956855
PART NAME
QTY.
REMARKS
CYLINDER HEAD COMP. ....................................... 1 .......... INCLUDES ITEMS W/
*
GUIDE, VALVE, OS, OPTIONAL
1
GUIDE, EX. VALVE, OS, OPTIONAL
1
CLIP, VALVE GUIDE
1
GASKET, CYLINDER HEAD
1
COVER COMP., HEAD
1
GASKET, CYLINDER HEAD COVER
1
SEAT, VALVE SPRING
1
BOLT, HEAD COVER
1
BOLT, STUD 8X123
2
BOLT, STUD 8X47
2
WASHER COMP., HEAD COVER
1
PIN A, DOWEL 12X20
2
BULK HOSE, VACUUM 11X1000, 11X100
1
BOLT, FLANGE 10X80
4
SPARK PLUG, BPR6ES, NGK
1
SPARK PLUG, W20EPR-U, DENSO
1
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 85
HONDA GX-240K1 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 86 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
1
2
3
4
5
7
9
PART NO.
16731ZE2003
19610ZE2010ZC
19631ZE2D00
32197ZH8003
36100ZE1015
90013883000
90684ZA0601
PART NAME
CLIP, TUBE
COVER COMP., FAN *NH1* BLACK
SHROUD
SUB-HARNESS
SWITCH ASSY., ENGINE STOP
BOLT, FLANGE 6X12, CT200
CLIP, WIRE HARNESS
QTY.
1
1
1
1
1
6
1
REMARKS
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 87
HONDA GX-240K1 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 88 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
4
7
8
PART NO.
19511ZE2000
28450ZE2W11
31100ZE2010
90201ZE3V00
90741ZE2000
PART NAME
FAN, COOLING
PULLEY COMP., STARTER, SCREEN GRID
FLYWHEEL COMP.
NUT, SPECIAL 16MM
KEY, SPECIAL WOODRUFF 25X18
QTY.
1
1
1
1
1
REMARKS
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 89
HONDA GX-240K1 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
PAGE 90 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
NO.
1
2
3
5
6
*
8
11
12
13
14
15
PART NO.
16854ZH8000
16955ZE1000
17510ZE2020ZD
17620ZH7023
17631ZH7003
17672ZE2W01
91353671003
9405008000
950014500360M
9500202080
957010802500
PART NAME
QTY.
REMARKS
RUBBER SUPPORTER 107MM
1
JOINT, FUEL TANK
1
TANK COMP., FUEL *NH1*, BLACK
1
CAP COMP., FUEL FILLER .................................... 1 .......... INCLUDES ITEMS W/
*
GASKET, FUEL FILLER CAP
1
FILTER, FUEL
1
O-RING 14MM, ARAI
1
NUT, FLANGE 8MM
2
BULK HOSE, FUEL 4.5X3000, 4.5X222
1
CLIP, TUBE, B8
2
BOLT, FLANGE 8X25
2
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 91
NOTE PAGE
PAGE 92 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — GASKET KIT ASSY.
GASKET KIT ASSY.
NO.
1
1
2
3
4
5
6
PART NO.
06111ZE2408
11381ZE2800
11381ZE2801
12251ZE2800
12391ZE2020
16221ZA0800
16223ZA0800
18333ZE3800
PART NAME
GASKET KIT
GASKET, CASE COVER
GASKET, CASE COVER
GASKET, CYLINDER HEAD
GASKET, CYLINDER HEAD COVER
GASKET, CARBURETOR
GASKET, INSULATOR
GASKET, EX. PIPE
QTY.
1
1
1
1
1
1
1
1
REMARKS
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 93
HONDA GX-240K1 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 94 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
2
6
8
11
PART NO.
30500ZE2023
30700ZE1013
31512ZE2000
36101ZE1010
90015883000
PART NAME
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
GROMMET, WIRE
WIRE, STOP SWITCH 370MM
BOLT, FLANGE 6X28
QTY.
1
1
1
1
2
REMARKS
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 95
HONDA GX-240K1 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 96 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
2
3
4
5
6
7
8
10
11
12
13
14
PART NO.
18310ZE2W00
18320ZE2W01
18323ZE2W00
18330ZE2W00
18331ZE2810
18333ZE3800
18355ZE2010
18381ZE2W10
90013883000
90050ZE1000
90055ZE1000
90050ZE1000
9405008000
PART NAME
MUFFLER COMP.
PROTECTOR COMP., MUFFLER
PROTECTOR, EX. PIPE
PIPE, EX.
CAP, MUFFLER
GASKET, EX. PIPE
ARRESTER, SPARK
GASKET, MUFFLER, ARRESTER
BOLT, FLANGE 6X12 CT200
SCREW, TAPPING 5X8
SCREW, TAPPING 4X6
SCREW, TAPPING 5X8
NUT, FLANGE 8MM
QTY.
1
1
1
1
1
1
1
1
1
6
3
1
5
REMARKS
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 97
HONDA GX-240K1 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 98 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — PISTON ASSY.
PISTON ASSY.
NO.
1
1
1
1
2
2
2
2
3
4
4
5
*
6
PART NO.
13010ZE2013
13011ZE2013
13012ZE2013
13013ZE2013
13101ZE2W00
13102ZE2W00
13103ZE2W00
13104ZE2W00
13111ZE2000
13200ZE2000
13200ZE2305
90001ZE8000
90551ZE1000
PART NAME
QTY.
REMARKS
RING SET, PISTON, STD.
1
RING SET, PISTON, OS 0.25, OPTIONAL
1
RING SET, PISTON, OS 0.50, OPTIONAL
1
RING SET, PISTON, 0.75, OPTIONAL
1
PISTON, STANDARD
1
PISTON, OS 0.25, OPTIONAL
1
PISTON, OS 0.50, OPTIONAL
1
PISTON, 0.75, OPTIONAL
1
PIN, PISTON
1
ROD ASSY., CONNECTING STANDARD ................ 1 .......... INCLUDES ITEMS W/
*
ROD ASSY., CONNECTING, US 0.25, OPT.
1
BOLT, CONNECTING ROD
2
CLIP, PISTON PIN 18MM
2
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 99
HONDA GX-240K1 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 100 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
1
2
*
3
*
4
*
5
*
6
*
7
*
8
*
10
*
11
*
12
*
13
*
14
PART NO.
28400ZE2W01ZB
28410ZE2W01ZB
28421ZE2W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28461ZE2W02
28462ZE2W11
28469ZE2W01
90004ZE2W01
90008ZE2003
PART NAME
QTY.
REMARKS
STARTER ASSY., RECOIL *NH1*, BLK ............... 1 ......... INCLUDES ITEMS W/
*
CASE COMP., RECOIL STARTER *NH1*, BLK 1
PULLEY, RECOIL STARTER
1
RATCHET, STARTER
2
SPRING, FRICTION
1
SPRING, STARTER RETURN
1
SPRING RATCHET
2
RETAINER, SPRING
1
GRIP, STARTER
1
ROPE, RECOIL STARTER
1
GRIP, REINFORCEMENT
1
SCREW, CENTER
1
BOLT, FLANGE 6X10
3
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 101
HONDA GX-240K1 ENGINE — LABELS ASSY.
LABELS ASSY.
PAGE 102 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
HONDA GX-240K1 ENGINE — LABELS ASSY.
LABELS ASSY.
NO.
1
2
3
5
15
16
PART NO.
87521ZE2W01
87522ZE1810
87522ZH9000
87528ZE2810
87586ZH7W00
87532ZH8810
PART NAME
EMBLEM, INTERNAL
MARK, CAUTION, EXTERNAL
LABEL, CAUTION
MARK, CHOKE, EXTERNAL
LABEL, FUEL CAUTION
MARK, OIL ALERT
QTY.
1
1
1
1
1
1
REMARKS
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 103
ROBIN EH25-2 ENGINE — CRANKCASE ASSY.
CRANKCASE ASSY.
PAGE 104 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
ROBIN EH25-2 ENGINE — CRANKCASE ASSY.
CRANKCASE ASSY.
NO.
10
20+
30
*
40
*
45
*
50
*
60+
80
90
210
220#
230#
235#
PART NO.
2541010131
13212AA080
0440300030
0600300220
0600150010
0310060020
0105080290
0401140030
0211140020
2541100301
0440300030
0600300220
0600150010
1600280010
250
2344500101
260
2054190103
270
2276360107
280% 0213160020
290
2541600103
300
0011308300
330
2541750213
340
0043505100
610
2701300101
620
2541500113
630
0110100040
680
2701550303
690
2701600403
700
0310060020
710
0110060020
810
2541430101
820
2541440111
830
2461600603
840
2461600713
850
0851080000
0851080000
960
2549900107
PART NAME
QTY.
REMARKS
CRANKCASE CP ....................................... 1 .................. INCLUDES ITEMS W/
*
VALVE GUIDE
2
OIL SEAL
1
BALL BEARING BB-6206C3 ...................... 1 .................. REPLACES 0600300020
BALL BEARING BB-6202C3
1
DOWEL PIN
2
STUD
2
PLUG
2
GASKET
2
MAIN BEARING COVER CP ..................... 1 .................. INCLUDES ITEMS W/#
OIL SEAL
1
BALL BEARING BB-6206C3 ...................... 1 .................. REPLACES 0600300020
BALL BEARING BB-6206C3
1
BALL BEARING BB-62/28C3
1
GOVERNOR GEAR CP
1
GOVERNOR SLEEVE
1
OIL GAUGE ASSY. .................................... 1 .................. INCLUDES ITEM W/%
GASKET
1
GASKET, BEARING COVER
1
BOLT AND WASHER ASSY.
8
OIL SHELTER (SENSOR)
1
SCREW AND WASHER ASSY.
3
CYLINDER HEAD CP ................................ 1 .................. INCLUDES ITEMS W/+
GASKET, HEAD
1
FLANGE BOLT
4
ROCKER COVER
1
GASKET, ROCKER COVER
1
DOWEL PIN
2
FLANGE BOLT
6
BREATHER COVER CP
1
BREATHER PLATE CP
1
GASKET, BREATHER COVER
1
GASKET, BREATHER PLATE
1
RUBBER PIPE, 8 X11 X 60"
1
RUBBER PIPE, 8 X11 X 75" Cyclone
1
GASKET SET
1
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 105
ROBIN EH25-2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 106 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
ROBIN EH25-2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
10
40
50
60
70
210
310
320
*
350
360
370
380
PART NO.
2542090101
0230300170
0230300180
0230300190
0021808000
0032018000
0323030010
2542410103
2542250100
2462300103
2702330103
2702340103
2702340203
2702340303
2542350107
2542350207
2542350307
0565180010
PART NAME
QTY.
REMARKS
CRANKSHAFT CP ..................................... 1 ................... SAE 1” KEYED SHAFT
SPACER T=0.6 ........................................... 1 ................... SELECT 1 SPACER ONLY
SPACER T=0.8 ........................................... 1 ................... SELECT 1 SPACER ONLY
SPACER T=1.0 ........................................... 1 ................... SELECT 1 SPACER ONLY
NUT
1
SPRING WASHER
1
WOODRUFF KEY
1
BALANCER SHAFT
1
CONNECTING ROD ASSY. ....................... 1 ................... INCLUDES ITEMS W/
*
CONNECTING ROD BOLT
2
PISTON PIN
1
PISTON , STANDARD
1
PISTON, OVERSIZE 0.25 MM
1
PISTON, OVERSIZE 0.50 MM
1
PISTON RING SET, STANDARD
1
PISTON RING SET, OVERSIZE 0.25 MM 1
PISTON RING SET, OVERSIZE 0.50 MM 1
CLIP
2
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 107
ROBIN EH25-2 ENGINE — INTAKE AND EXHAUST ASSY.
INTAKE AND EXHAUST ASSY.
PAGE 108 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
ROBIN EH25-2 ENGINE — INTAKE AND EXHAUST ASSY.
INTAKE AND EXHAUST ASSY.
NO.
PART NO.
10
2543170141
35
* 2543640113
36
0051904100
*
37
* 0031522000
50
2393330113
60
2463361103
70
2463371103
80
2703340103
90
2703350103
95
2463550103
210
2703530103
220
26136001A3
230
2693580103
240
0170060090
260
2703650103
310
2703010101
320
2543420111
340
2463520103
350
0170080030
360
0152006090
363
0152060100
365
0011008160
430
2703480103
440
2463700107
445%
0150040060
500
2543300101
505+
0105060191
510
2543261310
510-2# 2343600308
510-3# 2073269008
520#
2343260407
540
2343290103
555
2463600113
556
0011308280
560
2343590203
570
2263921200
580
0011006120
650
2304390101
PART NAME
QTY.
REMARKS
CAMSHAFT CP ........................................... 1.................. INCLUDES ITEM W/
*
RELEASE LEVER
1
SPRING PIN
1
SNAP RING
1
TAPPET
2
VALVE SPRING
2
SPRING RETAINER
2
INTAKE VALVE
1
EXHAUST VALVE
1
COLLET VALVE
4
PUSH ROD
2
ROCKER ARM
2
BOLT, PIVOT
2
NUT
2
GUIDE PLATE
1
MUFFLER CP
1
MUFFLER COVER
1
GASKET, MUFFLER
1
NUT
2
TAPPING BOLT
4
TAPPING BOLT
1
BOLT AND WASHER ASSY.
1
EXHAUST PIPE COVER
1
DEFLECTOR ASSY. .................................... 1.................. INCLUDES ITEM W/%
TAPPING SCREW
3
INTAKE PIPE CP ......................................... 1.................. INCLUDES ITEM W/+
STUD
2
AIR CLEANER ASSY. .................................. 1 ................. INCLUDES ITEM W/#
PACKING
1
GROMMET
1
ELEMENT SET
1
INSULATOR
1
GASKET, INTAKE PIPE
1
BOLT AND WASHER ASSY.
3
GASKET 2, INSULATOR
2
NUT AND WASHER ASSY.
2
BOLT AND WASHER ASSY.
2
CHOKE KNOB
1
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 109
ROBIN EH25-2 ENGINE — GOVERNOR ASSY.
GOVERNOR ASSY.
PAGE 110 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
ROBIN EH25-2 ENGINE — GOVERNOR ASSY.
GOVERNOR ASSY.
NO.
10
20
30
40
50
60
70
80
310
320
*
330
*
340
345
346
350
360
370
380
410
440
450
PART NO.
2544230123
2464220123
2544270101
2544280103
0031306000
0011406300
0186060020
2544250113
2704330200
2704330201
2274360103
2704350103
0043104250
2694550303
2274500203
0043106300
0022706000
0110060050
2544420123
0043104080
0022706000
PART NAME
QTY.
REMARKS
GOVERNOR LEVER
1
GOVERNOR SHAFT
1
GOVERNOR ROD CP
1
ROD SPRING
1
CLIP
2
BOLT AND WASHER ASSY.
1
NUT
1
GOVERNOR SPRING
1
SPEED CONTROL ASSY. .................... 1 ..............INCLUDES ITEM W/
*
SPEED CONTROL CP
1
KNOB
1
STOP PLATE
1
SCREW
1
IDLE SET SPRING
1
SPRING WASHER
1
SCREW
1
NUT
1
FLANGE-BOLT
1
WIRE BRACKET
1
SCREW
1
NUT
1
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 111
ROBIN EH25-2 ENGINE — COOLING AND STARTING ASSY.
COOLING AND STARTING ASSY.
PAGE 112 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
ROBIN EH25-2 ENGINE — COOLING AND STARTING ASSY.
COOLING AND STARTING ASSY.
NO.
10
20
40
45
90
210
210-1
*
210-2
*
210-3
*
210-4
*
210-5
*
210-6
*
210-11
*
210-35
*
210-49
*
220
PART NO.
2545345001
2545355011
2709170303
0110060020
0732004950
2545270103
2705020100
2705011508
2705012008
2705011008
2615010008
2705012508
2275013108
2705014508
2705026108
2275015208
0110060010
PART NAME
QTY.
REMARKS
BLOWER HOUSING CP
1
BLOWER HOUSING CP
1
LABEL, TRADE MARK
1
FLANGE BOLT
5
LABEL, RECOIL OHV
1
HEAD COVER
1
RECOIL STARTER ASSY. ............ 1 ................ INCLUDES ITEMS W/
*
SPIRAL SPRING
1
REEL
1
STARTER ROPE
1
STARTER KNOB
1
RATCHET
2
FRICTION SPRING
1
STARTER PULLEY
1
RATCHET GUIDE
1
SET SCREW
1
FLANGE BOLT
4
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 113
ROBIN EH25-2 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
PAGE 114 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
ROBIN EH25-2 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
NO.
10
20
30
40
50
50-1
50-2
50-3
50-4
50-8
50-15
70
80+
90+
105
210
PART NO.
2546105011
0732003900
0430430015
0641360010
0642008600
0642004110
0642001430
0642001410
0642002360
0642002790
0642003230
2346260101
0851060000
0561110020
0011308200
2546252300
PART NAME
QTY.
REMARKS
FUEL TANK CP
1
LABEL, CAUTION
1
FUEL TANK CAP CP
1
FUEL FILTER CP
1
FUEL STRAINER ASSY. ...................... 1 ............. INCLUDES ITEMS W/
*
FILTER
1
RUBBER PACKING
1
CLIP
1
LOCK NUT
1
LOCK BOLT
1
SPRING
1
FUEL PIPE CP ..................................... 1 ............. INCLUDES ITEMS W/+
RUBBER PIPE 6 X 12 X 75
1
HOSE CLAMP
2
BOLT AND WASHER ASSY.
4
CARBURETOR ASSY.
1
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 115
ROBIN EH25-2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 116 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
ROBIN EH25-2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
210
2546252300
210-1
2396253508
* 2096235108
210-2
* 2546252508
210-3
* 2376245108
210-4
* 2546242008
210-5
* 2466243608
210-6
* 2306244808
210-7
* 2346252108
210-8
* 2396256008
210-9
*
210-11 2546253108
*
210-12 2246254408
*
210-13 2266255008
*
210-14 2246231208
*
210-15 2146251508
*
210-16 2246255208
*
210-17 2076234508
*
210-18 2066254008
*
210-19 2346250608
*
210-20 2546244008
*
210-22 2546240308
*
210-23 2466245508
*
210-24 2246256918
*
210-32 1066239208
*
210-40 2466243508
*
210-41 2306244608
*
210-61 2476255008
*
210-62 2366268008
*
210-89 2466242508
*
210-101 1566235108
*
210-121 2466255108
*
PART NAME
QTY.
REMARKS
CARBURETOR ASSY. ....................... 1 ..............INCLUDES ITEMS W/
*
THROTTLE VALVE
1
SCREW
2
VALVE, CHOKE
1
SCREW, PANHEAD
2
PILOT JET
1
ADJUSTER
1
SPRING
1
CHOKE LEVER ASSY.
1
RING
1
SHAFT ASSY., THROTTLE
1
BOLT
1
RING
1
NEEDLE VALVE ASSY.
1
FLOAT PIN
1
FLOAT CHAMBER BODY1
INSERT WASHER
1
PACKING, CHAMBER
1
FLOAT ASSY.
1
MAINNOZZLE
1
MAIN JET
1
BOLT
1
CLIP
1
SEAL
1
ADJUST SCREW
1
SPRING
1
CAP
1
SEAL
1
GUIDE HOLDER
1
PACKING
1
CAP
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 117
ROBIN EH25-2 ENGINE — RECOIL START ASSY.
RECOIL START ASSY.
PAGE 118 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
ROBIN EH25-2 ENGINE — RECOIL START ASSY.
RECOIL START ASSY.
NO.
10
11
30
60
70
90
100
110
PART NO.
2347020111
2547943021
0011406250
0660000361
0150040090
0566120050
0650140031
0650140150
0650141030
0655000051
PART NAME
FLYWHEEL CP
IGNITION COIL CP
BOLT AND WASHER ASSY.
SWITCH ASSY.
TAPPING SCREW
CLAMP
SPARK PLUG, NGK (BR-6HS)
SPARK PLUG
SPARK PLUG, CHAMPION (L86C)
SPARK PLUG CAP
QTY.
1
1
2
1
2
1
1
1
1
1
REMARKS
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 119
ROBIN EH25-2 ENGINE — OIL SENSOR ASSY.
OIL SENSOR ASSY.
PAGE 120 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
ROBIN EH25-2 ENGINE — OIL SENSOR ASSY.
OIL SENSOR ASSY.
NO.
700
760
790
PART NO.
KS31102801
2147312201
2147900301
PART NAME
OIL SENSOR CP 19
WIRE 22 CP
CLAMP CP
QTY.
1
1
1
REMARKS
W/OIL SENSOR
W/OIL SENSOR
W/OIL SENSOR
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 121
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5.
Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
6.
The following items are not returnable:
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
a.
SPECIAL EXPEDITING SERVICE
Terms of payment for parts are net 30 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
b.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
RETURNED GOODS POLICY
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
1.
2.
A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
c.
Any line item with an extended
dealer net price of less than
$5.00.
d.
Special order items.
e.
Electrical components.
f.
Paint, chemicals, and lubricants.
g.
Decals and paper products.
h.
Items purchased in kits.
7.
The sender will be notified of any material
received that is not acceptable.
To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
8.
Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
a.
The parts numbers and descriptions
must match the current parts price
list.
9.
b.
The list must be typed or computer
generated.
Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
c.
The list must state the reason(s)
for the return.
d.
The list must reference the sales
order(s) or invoice (s) under
which the items were originally
purchased.
e.
The list must include the name
and phone number of the person
requesting the RMA.
3.
A copy of the Return Material Authorization
must accompany the return shipment.
4.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
Effective: February 22, 2006
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
PAGE 122 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)
NOTE PAGE
B-SERIES WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #9 (07/06/10) — PAGE 123
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
Contact: mq@multiquip.com
MQ Parts Department
Tel. (800) 421-1244
Fax (800) 537-3927
Mayco Parts
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Warranty Department
800-306-2926
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
800-421-1244, Ext. 279
310-537-3700, Ext. 279
Fax: 310-537-1173
Technical Assistance
800-421-1244
310-537-3700
Fax: 310-537-4259
800-478-1244
Fax: 310-631-5032
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: pmastretta@cipsa.com.mx
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Unit 2, Northpoint Industrial Estate,
Global Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: sales@multiquip.co.uk
Tel: 0161 339 2223
Fax: 0161 339 3226
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: jmartin@multiquip.com
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2010, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Whiteman logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download PDF