Windsor | LB1500IA | Operating instructions | Windsor LB1500IA Operating instructions

FLOOR BURNISHER
MODELS:
U1500
10090570
LB1500
10090160
LB1500IE
10090180
LB1500IA
10090170
Operating Instructions (ENG)
86309590-C
04/13/09
SPT1500
10090360
MACHINE DATA LOG
Model:
Date of Purchase:
Serial Number:
Sales Representative:
Address:
Phone Number:
1
86309590 (1500) BURNISHER 10/08/08
NOTES:
86309590 (1500) BURNISHER 10/08/08
2
TABLE OF CONTENTS
Machine Data Log/Overview………………... 1
Table of Contents ......................................... 3
HOW TO USE THIS MANUAL
How to use this Manual. ...............................1-1
SAFETY
Important Safety Instructions ........................ 2-1
Hazard Intensity Level. .................................2-2
Grounding Instructions-120V. ....................... 2-3
Grounding Instructions-230V ........................ 2-4
Safety Label Location ................................... 2-5
OPERATION
Technical Specifications ...............................3-1
Handle Installation ........................................3-2
Operation ......................................................3-4
Pad Driver Installation...................................3-4
MAINTENANCE
Machine Troubleshooting .............................4-1
Service Schedule..........................................4-2
GROUP PARTS LIST
Deck............................................................ 5-1
Drive/Pad Lock ........................................... 5-3
Electrical ..................................................... 5-5
Handle ........................................................ 5-7
Motor........................................................... 5-9
Wiring-120V ................................................ 5-11
Wiring-230V ................................................ 5-12
Suggested Spare parts ............................... 5-13
3
86309590 (1500) BURNISHER 10/08/08
HOW TO USE THIS MANUAL
This manual contains the following sections:
-
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
MAINTENANCE
PARTS LIST
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
Parts may be ordered from authorized dealers.
When placing an order for parts, the machine
model and machine serial number are important.
Refer to the MACHINE DATA box which is filled
out during the installation of your machine. The
MACHINE DATA box is located on the inside of
the front cover of this manual.
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
The PARTS LIST section contains assembled
parts illustrations and corresponding parts list. The
parts lists include a number of columns of
information:
-
The SAFETY section contains important
information regarding hazard or unsafe practices
of the machine. Levels of hazards are identified
that could result in product or personal injury, or
severe injury resulting in death.
-
REF – column refers to the reference
number on the parts illustration.
PART NO. – column lists the part
number for the part.
PRV NO. - Reference No.
QTY – column lists the quantity of the
part used in that area of the machine.
DESCRIPTION – column is a brief
description of the part.
SERIAL NO. FROM – If this column
has an (*) and a Reference number,
see the SERIAL NUMBERS page in
the back of your manual. If column
has two asterisk (**), call manufacturer
for serial number. The serial number
indicates the first machine the part
number is applicable to. The main
illustration shows the most current
design of the machine. When a boxed
illustration is shown, it displays the
older design.
NOTES – column for information not
noted by the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
NOTE: The number on the lower left corner of the
front cover is the part number for this manual.
86309590 (1500) BURNISHER 10/08/08
1-1
SAFETY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
To reduce the risk of fire, electric shock, or injury:
Use only indoors. Do not use outdoors or expose to rain.
Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water,
return it to an authorized service center.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce
airflow.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine
near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories,
shops and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
During operation, attention shall be paid to other persons, especially children.
The machine shall only be operated by instructed and authorized persons.
When leaving unattended, unplug the machine.
Do not handle the plug or machine with wet hands.
Do not unplug machine by pulling on cord. To unplug, grasp the plug, not the cord.
Do not use with damaged cord or plug. Follow all instructions in this manual concerning grounding the
machine.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or
corners.
Do not pull/run machine over cord. Keep cord away from heated surfaces.
Connect to a properly grounded outlet. See Grounding Instructions.
If the supply cord is damaged it must be replaced by a special cord from an authorized service agent.
Unplug machine before cleaning or servicing.
Operational hazard may occur when running the machine over the supply cord.
This appliance has been designed for use with pads specified by the manufacturer. The fitting of other pads
may affect its safety.
This machine is for dry use only and shall not be used or stored outdoors in wet conditions.
SAVE THESE INSTRUCTIONS
2-1
86309590 (1500) BURNISHER 10/08/08
SAFETY
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words – WARNING and CAUTION and FOR
SAFTEY. The level of hazard intensity is determined by the following definitions:
WARNING – Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION – Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or equipment. Read this information carefully. Know when these conditions can exist. Locate all
safety devices on the devices on the machine. Please take the necessary steps to train the machine
operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and Understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose fitting clothing, jackets, shirts, or sleeves when working on
the machine. Use approved replacement parts.
86309590 (1500) BURNISHER 10/08/08
2-2
SAFETY
GROUNDING INSTRUCTIONS 120V
THIS PRODUCT IS FOR COMMERCIAL
USE ONLY.
ELECTRICAL:
In the USA this machine operates on a 15 amp
nominal 120V, 60 hz, A.C. power circuit. The
amp, hertz, and voltage are listed on the data
label found on each machine. Using voltages
above or below those indicated on the data label
will cause serious damage to the motors.
Grounding Pin
GROUNDING CONNECTION
USING AN ADAPTOR
Grounded
Outlet
FIGURE A
Tab for Grounding
Screw
Metal Screw
Adaptor
Grounded
Outlet Box
FIGURE B
Adaptor
FIGURE C
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding provides
a path of least resistance for electric current to
reduce the risk of electric shock. This appliance
is equipped with a cord having an equipmentgrounding conductor and grounding plug. The
plug must be inserted into an appropriate outlet
that is properly installed and grounded in
accordance with all local codes and ordinances.
This appliance is for use on a nominal 120-volt
circuit, and has a grounded plug that looks like
the plug in “Fig. A”. A temporary adaptor that
looks like the adaptor in “Fig . C” may be used
to connect this plug to a 2-pole receptacle as
shown in “Fig. B”, if a properly grounded outlet
is not available. The temporary adaptor should
be used only until a properly grounded outlet
(Fig. A) can be installed by a qualified
electrician. The green colored rigid ear, lug, or
the like extending from the adaptor must be
connected to a permanent ground such as a
properly grounded outlet box cover. Whenever
the adaptor is used, it must be held in place by a
metal screw.
2-3
Note: Adaptors are not allowed in Canada.
Improper connection of the equipmentgrounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the outlet is properly
grounded. Do not modify the plug provided
with the appliance - if it will not fit the outlet,
have a proper outlet installed by a qualified
electrician.
86309590 (1500) BURNISHER 10/08/08
SAFETY
GROUNDING INSTRUCTIONS-230V
THIS PRODUCT IS FOR COMMERCIAL USE
ONLY.
ELECTRICAL:
The amp, hertz, and voltage are listed on the data
label found on each machine. Using voltages
above or below those indicated on the data label
will cause serious damage to the motors.
EXTENSION CORDS:
If an extension cord is used, the wire size must be
at least one size larger than the power cord on the
machine, and must be limited to 50 feet (15.5m) in
length.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding provides a
path of least resistance for electric current to
reduce the risk of electric shock. This appliance is
equipped with a cord having an equipmentgrounding conductor and grounding plug. The
plug must be inserted into an appropriate outlet
that is properly installed and grounded in
accordance with all local codes and ordinances.
Improper connection of the equipmentgrounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in doubt
as to whether the outlet is properly grounded.
Do not modify the plug provided with the
appliance - if it will not fit the outlet, have a
proper outlet installed by a qualified
electrician.
86309590 (1500) BURNISHER 10/08/08
2-4
SAFETY
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time, the
labels become illegible contact your authorized representative for prompt replacement.
WARNING LABEL
P/N 86219740
PRV NO. 500194
2-5
86309590 (1500) BURNISHER 01/21/09
OPERATION
TECHNICAL SPECIFICATIONS
ITEM
CONSTRUCTION
MOTOR
PAD SPEED
DIMENSION/CAPACITY/MODEL
Heavy-duty die cast aluminum deck
with heavy-duty rubber bumper,
tubular steel adjustable handle with die
cast aluminum handle housing and belt
driven pad.
1.5 hp
1500 rpm
ELECTRICAL SYSTEM
115 volts, 60 Hz
230 volts, 50 Hz
LB1500, U1500, SPT1500
LB1500IE, LB1500IA
CABLE
75’ [22.9 m]
SWITCHES
Dual levers with safety lock
WHEELS
HANDLE
DIMENSIONS (L X W X H)
Four 5” (12.7 cm) dia., 1.25” (3 cm)
wide, non-marking tread
1.5” (4 cm) tubular steel, adjustable,
easy to use thumb activated safety
lock
31.5” (80 cm) X 21.5” (54 cm) X 43.5”
(111 cm)
NOTE: Always use a pad, which has been designed for electric ultra high speed burnishing of at
least 2000 rpm.
The sound pressure level at the operator’s ear was measured to be 62 dBA. This was a nearfield,
broad-band measurement taken in a typical industrial environment on a tile floor. This appliance
contains no possible source of impact noise. The instantaneous sound pressure level is below 63 Pa.
86309590 (1500) BURNISHER 10/08/08
3-1
OPERATION
HANDLE INSTALLATION
HANDLE
RECEPTACLE
HANDLE
ASSEMBLY
4
5
6
MOTOR
PLUG
DECK
ASSEMBLY
PIVOT
HOLE
3
1
2
The machine is shipped with handle unassembled.
Follow these steps for installation:
1. Remove handle and deck assembly from carton.
2. Attach handle assembly to base using hardware kit
(86219680 – PRV NO. 47331) (attached to handle
in plastic bag) items 1, 2 and 3.
3. Remove bolt, nut and washers (items 4, 5
and 6) from lower block on handle assembly.
Attach links as shown. Tighten bolt and nut
securely, then back off 1/4 to 1/2 turn.
4. Check handle for movement up and down.
5. Plug motor cord into handle cord receptacle.
NOTE: The spacers (item 1) are required for the
correct operation of the handle. The spacers are
positioned completely inside the pivot holes in the
casting, and are held in place by tightening the bolts
and washers (items 2 and 3 against the spacer.
3-2
86309590 (1500) BURNISHER 01/21/09
OPERATION
CONTROLS
1. Safety Lock – Prevents unintended operation
of the machine.
2. Switch Levers – Turns machine on/off.
3. Adjustment Handle – Allows the handle to be
adjusted to a comfortable operating position.
1
NOTE: It is incorrect to make it lock
opposite from the way it was assembled by
applying more force to the nut.
The pivot pin is off center in relationship to the
axis of the handle. To adjust handle, tighten
nut on handle while in the locked position. The
handle is locked when the screw is to the
outside of the machine and the flat on the
opposite side of the handle is flush to the
bracket.
PIVOT PIN
HANDLE
2
2
LOCKING SIDE FLAT
3
HANDLE HEIGHT ADJUSTMENT
NOTE: The handle is in the up, locked
position from the factory.
1
3
4
2
The handle adjust bar (1) for the polishers are
individually preset at the factory for optimum
locking efficiency and minimum effort of
engaging. It should not be necessary to adjust
the handle adjust bar unless the handle
adjustment bar (1) the washer (3) and nut (2)
have been disturbed.
86309590 (1500) BURNISHER 10/08/08
3-3
OPERATION
MACHINE OPERATION
DAILY MAINTENANCE
1. Inspect power cord for wear. To prevent
electrical shock replace cords with frayed or
cracked insulation immediately.
For indoor use only.
2. Place machine in the storage position.
When using the pad, always keep the machine
moving when in contact with the floor.
3. Check pad condition. Change if soiled or torn.
PAD INSTALLATION
High starting torque. Hold machine firmly with
both hands.
1. Ensure that the pad driver is in good shape.
Install or change pad if necessary.
2. Plug the machine into a wall outlet as
described in the grounding instructions.
3. Lower the handle by unlocking the adjustment
handle and moving the handle into position.
Relock the handle when it is in a comfortable
position.
1. Lay machine back, exposing the under
side.
2. Remove center lock by turning counterclockwise.
3. Ensure pad is centered on pad driver. Pull
pad to edge of pad driver in several
directions to check for proper
engagement.
4. Replace center lock by turning clockwise
firmly compressing the center of the pad.
Insure that handle is locked in position before
starting machine.
4. Push the safety lock forward, unlocking the
switch levers.
5. With the safety lock forward, squeeze one or
both of the switch levers, turning the machine
on. (These levers can be operated
independently of each other). The safety lock
will not re-engage until both levers are
released.
6. To stop the machine, release the switch
levers.
7. Do not let machine rest on pad. When
finished with the machine, return handle to the
storage position.
NOTE: The machine is equipped with a circuit
breaker to protect the motor in the event an
overload condition occurs. The circuit breaker
is located on the handle. Push the reset button
to restart the machine. If the breaker trips
again, correct the cause of overloading before
proceeding.
3-4
86309590 (1500) BURNISHER 10/08/08
NOTES:
86309590 (1500) BURNISHER 10/08/08
3-5
MAINTENANCE
MACHINE TROUBLESHOOTING
PROBLEM
Machine will not run
CAUSE
Circuit breaker tripped in
building.
Power switch failure
Tripped circuit breaker
Faulty power cord
Fuse in motor blown
Electrical shock
Equipment not grounded
Receptacle not grounded
Internal wiring problem
Repeated circuit breaker
tripping
Mechanical problem
Faulty circuit breaker
Excessive vibration
Pad does not turn but motor is
running
4-1
Pad not centered
Damaged or unevenly worn
pad
Damaged pad driver
Belt is loose or broken
SOLUTION
Check and reset.
Test switch for continuity and
replace if necessary.
Reset.
Replace.
Replace
CAUTION: To reduce the risk
of electrical shock, unplug the
machine before opening fuse
holder. Fuse will only open
under extreme conditions.
Investigate cause before
replacing.
Follow grounding instructions
exactly.
Have an electrician inspects
building’s wiring.
Ensure that the machine wiring
matches the appropriate wiring
diagram. Replace any wires or
components that are short
circuiting.
Higher amp draws indicate a
mechanical problem. Find the
problem before using the
machine.
Test circuit for continuity.
Replace circuit breaker if
necessary.
Re-center pad.
Replace pad. Do not rest
machine on pad when not in
use.
Replace.
Adjust or replace belt.
86309590 (1500) BURNISHER 10/08/08
MAINTENANCE
SERVICE SCHEDULE
MAINTENANCE
DAILY
Check pad wear to prevent buildup of chemicals
*
Check pad driver system for damage
*
Check handles, switches, and knobs for damage
*
Store with pad off the floor
*
MONTHLY
Check all bearings for noise
*
Check skirt/bumpers for damage and replace as necessary
*
Check overall performance of machine
*
86309590 (1500) BURNISHER 10/08/08
4-2
DECK
1
8
3
14
13
12
11
4
10
15
5
7
9
5-1
8
86309590 (1500) BURNISHER 10/08/08
6
2
DECK
REF
PART NO.
PRV NO.
QTY
1
2
3
4A
4B
5
6
7
8
9
10
11
12
13
14
15
86288730
86288740
86215460
86217630
86288990
86214930
86226020
86225720
86137280
86136640
86214950
86276570
86137340
86216600
86216360
86222270
70184
70709
140397
29229BLU
29229GRY
03111
89206
87203
87054
70262
03116
70691
87211
27871
14423
57276
4
2
2
1
1
1
4
8
8
4
1
2
2
2
1
2
DESCRIPTION
SERIAL NO.
FROM
NOTES:
SCR, M8 X 25HHCS
SET SCR, 8MMX1.25X8MM CUP PT
BRACKET, HANDLE LINK
DECK, 20 IN BURNISHER, BLUE
DECK, 20 IN BURNISHER, GRAY
AXLE, MAIN POLISHER
WHEEL, 5D X 1.25 X 13MM ID GRY
WASHER, 14MM ID X 36MM OD
WASHER, M8 FLAT DIN125A PLT
SCR, M8-1.25 X 20 HHMS PLTD
AXLE, MAIN BURNISHER
SCR, M6 X 25 HHCS
WASHER, M6 FLAT
CAP, EXTRUSION
BUMPER, EXTRUSION 42.6 IN
NUT, PUSH FLAT RD .51 ID
86309590 (1500) BURNISHER 04/13/09
5-2
DRIVE/PAD LOCK
1
17
16
15
4
6
14
8
9
3
7
2
10
13
11
12
11
5-3
86309590 (1500) BURNISHER 10/08/08
5
DRIVE/PAD LOCK
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
86214940
86217510
86276730
86004820
86223280
86225730
86275570
86223290
86223470
86222480
86246740
86276740
86006670
86223970
86223480
86215330
86223980
03115
27913
70719
48041
64106
87218
70505
64107
67449
66426
51353
70720
70201
09133
67450
14424
09134
1
1
3
1
1
1
1
1
1
1
1
3
8
1
2
1
1
DESCRIPTION
SERIAL NO.
FROM
NOTES:
AXLE, PAD DRIVER
COVER, BEARING
SCR, M4 X 8MM PPHMS
KEY, 3/16 SQ X 7/8 CRS
PULLEY, .625 X 3.45
WASHER, M6 (20.5OD X 1.67) PLT
SCR, 1/4-20 X 1.00 HHCS GR5
PULLEY, BURNISHER
RING, 20M EXTERNAL SNAP
PAD DRIVER, 20 IN BURNISHER FLEX
LOCK, PAD DRIVER BLUE
SCR, #10 X 3/8 PPHST TYPE B
SCR, 1/4-20 X 3/4 FHCS
BEARING, 20MM X 52MM
RING, 52MM INTERNAL SNAP
BELT, DRIVE 38 IN
SEALED BALL BEARING, 25MM X 52MM
86309590 (1500) BURNISHER 10/08/08
5-4
ELECTRICAL
8
7
11
9
6
14A-B
5
10
2
1
3 A-C
4
12
13
5-5
86309590 (1500) BURNISHER 01/21/09
ELECTRICAL
REF PART NO. PRV NO. QTY
DESCRIPTION
1
2
3A
3B
86002010
86198450
86216950
86234140
14942
20005
23212
23254
1
1
1
1
BOOT, 3/8 CIRCUIT BREAKER
CLAMP, 5/16 NYLON
CORD SET, EURO 1.5MM X 75 BLK
CORD SET, 14/3 ST C 75’ YLW
3C
86234140
23154
1
CORD SET, 14/3 ST X 75FT, YLW
4
5
6
7
8
9
10
11
12
13
14A
14B
86216920
86268450
86136780
86007110
86224750
86137290
86137330
86215140
86224930
86224300
86312460
86291460
23206
70689
70801
72123
73993
87057
87208
140674
730012
730021
-
1
1
2
2
1
2
1
1
1
1
1
1
CORDSET, 14/3 X 52 IN, SJT, BLK
SCR, M4.8 X 10 HHTF TYPE B
SCR, M3.5 X 40 PHTF
SWITCH, 25A SPST 125-250V SNAP
SPRING, COMP, .48OD X .91
WASHER, M4 LOCK
WASHER, M5 LOCK
BARRIER SHEET
STRAIN RELIEF, 14/3 STRAIGHT
SPACER, POLISHER HANDLE
BREAKER, 14A VDE CIRCUIT
BREAKER, 11A VDE CIRCUIT
86309590 (1500) BURNISHER 10/08/08
SERIAL NO.
NOTES
FROM
LB1500IE
LB1500IA
LB1500,
U1500,SPT1500
120V
230V
5-6
HANDLE
5
17
6
27
3
16
12
13
7
1
2 14 19
22 14
9
10
21
24
8
20
4
15
8
25
11
18 23
8
23
20
18
11
5-7
86309590 (1500) BURNISHER 01/21/09
26
HANDLE
REF PART NO. PRV NO. QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
86215130
86216370
86004070
86311800
86005150
86005160
86136350
86136360
86222560
86223550
86274230
86136670
86136680
86288450
86136720
86224740
86225370
86137280
86279080
86010720
86225710
86137330
86224290
86310950
86218500
86311810
86311820
14344
14434
36196
51326
51327
57274
57275
66334
67430
70135
70686
70687
70689
70701
73990
78437
87054
87058
87086
87202
87208
730008
38316
-
1
1
2
1
1
2
4
2
1
1
2
2
2
4
1
2
1
2
2
3
1
2
2
1
1
1
1
DESCRIPTION
SERIAL NO.
FROM
NOTES
BAR, HANDLE ADJUST
BUMPER, BURNISHER HANDLE
GRIP, POLISHER HANDLE
TUBE ASSY, HANDLE ADJ.
LOCK, SAFETY HANDLE
LEVER, SWITCH
NUT, M6 HEX FINISH
NUT, M10 X 1.5 HEX NYLOK PLTD
PIN, PIVOT, HANDLE ADJUST
ROD, HANDLE ADJUST
SCR, M8 X 30 HHMS
SCR, M6 X 45 SHCS, BLK
SCR, M6 X 50 SHCS, BLK
SCR, M4.8 X 10 HHTF TYPE B
SCR, M10 X 1.50 X 90 HHCS PLTD
SPRING, EXT, .50D X 3.5L
TUBE, GRIP HANDLE
WASHER, M8 FLAT DIN15A PLT
WASHER, M4 FLAT DIN125A PLT
WASHER, M10 X 30 PLTD
WASHER, BEARING (HANDLE ADJ)
WASHER, M5 LOCK SHAKEPROOF PLTD
SPACER, .317ID X .5OD X .44LG
CLAMP, HANDLE
HANDLE, BRNSHR EXTND
HOUSING, POLSHR HANDLE RR, CB
HOUSING, POLSHR HANDLE FRT,CB
86309590 (1500) BURNISHER 10/08/08
5-8
MOTOR
5
4
3A-B
2
1
5-9
86309590 (1500) BURNISHER 01/21/09
MOTOR
REF
PART
NO.
PRV
NO.
QTY
1
86006920
70507
4
2
3A
3B
86010720
86312240
86312230
87086
-
4
1
-
4
86223680
70700
8
5
86217500
27892
1
DESCRIPTION
SERIAL NO.
FROM
NOTES:
SCR, 3/8-16 X 3/4 HHCS GR5
PLT
WASHER, M10 X 3 PLTD
MOTOR, 115V 1.5HP 3000RPM
MOTOR, 230V 1.5HP 3000RPM
SCR, M5 X .8 X 10MM PHMS
BLK
COVER ASM, MOTOR 1.75HP
86309590 (1500) BURNISHER 10/08/08
5-10
WIRING-120V
CORD SET
WHT
GRN
BLK
-CB1
120V AC 15A
1
-SWITCH
-SWITCH
WHT
WHT
BLK
BLK
GRN
-MOTOR
GRN
REF
PART NO.
PRV NO.
QTY
1
86311830
-
1
5-11
DESCRIPTION
WIRE, 125MM, BLK/14,
76029X76029
86309590 (1500) BURNISHER 10/08/08
SERIAL NO.
FROM
NOTES:
M
WIRING-230V
CORD SET
WHT
BLK
GRN
-CB1
120V AC 15A
1
EMC FILTER
-SWITCH
-SWITCH
EMC FILTER2
WHT
WHT
BLK
BLK
GRN
-MOTOR
M
GRN
REF
PART NO.
PRV NO.
QTY
1
86311830
-
1
DESCRIPTION
SERIAL NO.
FROM
NOTES:
WIRE, 125MM, BLK/14,
76029X76029
86309590 (1500) BURNISHER 10/08/08
5-12
SUGGESTED SPARE PARTS
PART
NO.
86225710
86224740
86224750
86007110
86215130
86222560
86223550
86291460
86312460
PRV
NO.
87202
73990
73993
72123
14344
66334
67430
-
WASHER, BEARING (HANDLE ADJ)
SPRING, EXT, .5OD X 3.5L
SPRING, COMP, .48 OD X .91L
SWITCH, 25A SPST 125-250V SNAP
BAR, HANDLE ADJ
PIN, PIVOT ,HANDLE ADJ
ROD, HANDLE ADJ
BREAKER, 11A VDE CIRCUIT
BREAKER, 14A VDE CIRCUIT
86223390
67488
RECTIFIER, 50A 600V BRIDGE
86001820
86001720
86003660
86003670
86216600
86216360
86222480
86246740
14404
140785
34378
34379
27871
14423
66426
51353
86223970
09133
86223980
09134
86217510
86215330
27913
14424
BRUSH SET
BRUSH SET (SET OF 4)
FUSE
FUSE HOLDER
CAP, EXTRUSION
BUMPER, EXTRUSION 44.30 IN
PAD DRIVER, 20IN BURNISHER FLEX
LOCK, PAD DRIVER BLUE
SEALED BALL BEARING, 20MM X
52MM
SEALED BALL BEARING, 25MM X
52MM
COVER, BEARING
BELT, DRIVE 38 IN
5-13
DESCRIPTION
SERIAL NO.
FROM
86309590 (1500) BURNISHER 10/08/08
NOTES:
230V
120V
LB1500, U1500,
SPT1500
120V
230V
NOTES:
86309590 (1500) BURNISHER 10/08/08
5-14
Download PDF