php9030DJ GE Profile Series 30" Built-In Touch Control Induction Cooktop PHP9030DJ

php9030DJ GE Profile Series 30" Built-In Touch Control Induction Cooktop PHP9030DJ
GE Profile™ Series 30" Built-In Touch Control Induction Cooktop
Dimensions and Installation Information (in inches)
Important: Requires a 5" free area between
the bottom of the cooktop to any combustible
material, i.e., shelving. Free area not required when
installing wall oven underneath cooktop. Refer to
installation instructions. Requires a 15" minimum
from cooktop to adjacent overhead cabinets. Units
are furnished with a 48" flexible armored cable.
Note: 30" induction cooktops are approved for
use over select GE 27" and GE 30" Single Wall
Ovens and Warming Drawers. Refer to cooktop and
wall oven/warming drawer installation instructions
packed with product for current dimensional
data. If installed with a GE Telescopic Downdraft
System, consult both the cooktop and downdraft
installation instructions packed with product
before installing. Cooktop gas/electric supply
may need to be re-routed to install downdraft.
The countertop cutout requires 23-1/2” minimum
flat countertop surface and 25” minimum total
countertop depth. In addition, other clearances
to front edge of the countertop must be considered.
Before installing, consult installation instructions
packed with product for ­current dimensional data.
Cutout filler trim kit: A filler trim kit
is available for use if your countertop cutout is
larger than the dimension shown, up to 29-13/16" x
20-7/16". Order JXTR32B for black or JXTR32W
for white, to reduce the cutout opening for
installation of this cooktop. These kits may be
ordered from your GE Dealer.
Approximate Cooking Dimensions
13" MAX. depth of unprotected
overhead cabinets (when no
hood or microwave is installed)
4-5/8" at baffle near center of
unit (except when installed
above an approved wall oven)
3-1/4" at rear of air intake
to 19-3/4"
28-1/2" to
1-3/4" MIN.
to rear wall
30" MIN. from countertop to
unprotected cabinet (when
no hood or microwave is
15" MIN. height from countertop
to nearest cabinet (including
light rails) on both sides of
2-1/2" MIN.
Electrical junction box 16" MIN.
below countertop
To insure accuracy, it is best to make a
template when cutting the opening in the counter
2" MIN. clearance
to side wall from cut-out
on both sides of cooktop
KW Rating
240V 7.3
208V 6.4
240V 30.8 Amps†
208V 30.8 Amps†
†Note: Check local codes
for required breaker size
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at or call GE Answer Center®
service, 800.626.2000.
Listed by
Specification Created 1/15
GE Profile™ Series 30" Built-In Touch Control Induction Cooktop
Features and Benefits
Four Induction elements - Enjoy a new level of rapid, precise heating
with a cool-to-the-touch surface that’s easy to clean
Digital touch controls - Accurately control your heating and enjoy an
easy to clean surface
1 1" 3,700-watt induction element - Rapidly boil water with
GE's most powerfull induction element
SyncBurners - Control two 7" elements simultaneously to evenly heat
large cookware or griddles*
Kitchen timer - Helps coordinate meal preparation and cooking
Control lock capability - Protects against unintended activation
an presence & size sensor - Cook efficiently with elements that heat to
the size of your pan and shut off when no
pan is present
Red LED display with black glass surface - Achieve a modern look that
complements the entire kitchen
ot surface indicator lights - Know when elements are too
hot to touch with a quick glance
Model PHP9030DJBB - Black on black
*Optional Stainless Steel Clad
Aluminum Griddle
Achieve even results with this lightweight griddle,
tailored to fit GE SyncBurners. Order part number
JXGRIDL1 from your GE Dealer.
Specification Created 1/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF