php9030sJ GE Profile Series 30" Built-In Touch Control Induction Cooktop

php9030sJ  GE Profile Series 30" Built-In Touch Control Induction Cooktop
GE Profile™ Series 30" Built-In Touch Control Induction Cooktop
Dimensions and Installation Information (in inches)
Important: Requires a 5" free area between
the bottom of the cooktop to any combustible
material, i.e., shelving. Free area not required
when installing wall oven underneath cooktop.
Refer to installation instructions. Requires a 15"
minimum from cooktop to adjacent overhead
cabinets. Units are furnished with a 48" flexible
armored cable.
Note: 30" induction cooktops are approved
for use over select GE 27" and GE 30" Single
Wall Ovens and Warming Drawers. Refer
to cooktop and wall oven/warming drawer
installation instructions packed with product for
current dimensional data. If installed with a GE
Telescopic Downdraft System, consult both the
cooktop and downdraft installation instructions
packed with product before installing. Cooktop
gas/electric supply may need to be re-routed to
install downdraft. The countertop cutout requires
23-1/2" minimum flat countertop surface and 25"
minimum total countertop depth. In addition,
other clearances to front edge of the countertop
must be considered. Before installing, consult
installation instructions packed with product for
­current dimensional data.
Cutout filler trim kit: A filler trim kit
is available for use if your countertop cutout
is larger than the dimension shown, up to
29-13/16" x 20-7/16". Order JXTR32B for black or
JXTR32W for white, to reduce the cutout opening
for installation of this cooktop. These kits may be
ordered from your GE Dealer.
Approximate Cooking Dimensions
4-5/8" at baffle near center
ofunit (except when installed
above an approved wall
oven) and 3-1/4" at rear
of air intake
13" MAX. depth of unprotected
overhead cabinets (when no
hood or microwave is installed)
to 19-3/4"
28-1/2" to
1-3/4" MIN.
to rear wall
30" MIN. from countertop to
unprotected cabinet (when
no hood or microwave is
15" MIN. height from countertop
to nearest cabinet (including
light rails) on both sides of
2-1/2" MIN.
Electrical junction box 16" MIN.
below countertop
To insure accuracy, it is best to make a
template when cutting the opening in the counter
2" MIN. clearance
to side wall from cut-out
on both sides of cooktop
KW Rating
240V 7.3
208V 6.4
240V 30.8 Amps†
208V 30.8 Amps†
Note: Check local codes
for required breaker size
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at or call GE Answer Center®
service, 800.626.2000.
Listed by
Specification Created 1/15
GE Profile™ Series 30" Built-In Touch Control Induction Cooktop
Features and Benefits
Four Induction elements - Enjoy a new level of rapid, precise heating
with a cool-to-the-touch surface that’s easy to clean
igital touch controls - Accurately control your heating and enjoy an
easy to clean surface
1 1" 3,700-watt induction element - Rapidly boil water with
GE's most powerfull induction element
yncBurners - Control two 7" elements simultaneously to evenly heat
large cookware or griddles*
Kitchen timer - Helps coordinate meal preparation and cooking
Control lock capability - Protects against unintended activation
an presence & size sensor - Cook efficiently with elements that heat to
the size of your pan and shut off when no
pan is present
ed LED display with black glass surface and stainless steel trim R
Achieve a modern look that complements the entire kitchen and other
stainless steel appliances
Hot surface indicator lights - Know when elements are too
hot to touch with a quick glance
*Optional Stainless Steel Clad
Aluminum Griddle
Achieve even results with this lightweight griddle,
tailored to fit GE SyncBurners. Order part number
JXGRIDL1 from your GE Dealer.
Model PHP9030SJSS - Stainless Steel
Specification Created 1/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF