EMachines | V700 Series | User`s guide | eMachines V700 Series User`s guide

eMachines Projector
V700 Series
User's Guide
Copyright © 2010. Acer Incorporated.
All Rights Reserved.
eMachines Projector V700 Series User's Guide
Original Issue: 03/2010
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
eMachines Projector V700 Series
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
eMachines and the eMachines logo are registered trademarks of Acer Incorporated. Other companies'
product names or trademarks are used herein for identification purposes only and belong to their
respective companies.
"HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."
iii
Information for your safety and
comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
•
•
•
Install the power supply unit before connecting the power cord to the AC
power outlet.
Unplug the power cord before removing the power supply unit from the
projector.
If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
Warnings!
•
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
•
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
iv
•
•
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices, lamp.
Using electrical power
•
•
•
•
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.6 meters (15 feet) maximum length.
v
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
•
•
•
•
•
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
•
•
•
Do not look into the projector's lens when the lamp is on. The bright may
hurt your eyes.
Turn on the projector first and then signal sources
Do not place the product in following environments:
•
•
•
•
Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.
Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.
•
Locations near fire alarms.
•
•
Locations with an ambient temperature above 40 ºC/104 ºF.
Locations where the altitudes are higher than 10000 feet.
Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
vi
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
Do not face the projector lens to the sun. It can lead to fire.
When switching the projector off, suggest to ensure the projector
completes its cooling cycle before disconnecting power.
Do not turn off the main power abruptly or unplug the projector during
operation. It can lead to lamp breakage, fire, electric shock or other
trouble. The best way is to wait for the fan to turn off before turning main
power off.
Do not touch air outlet grille and bottom plate which becomes hot.
Clean the air filter frequently if have. The temperature inside may rise and
cause damage when the filter/ventilation slots clogged with dirt or dust.
Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
Always open the lens shutter or remove the lens cap when the projector is
on.
Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.
The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
The product will detect the life of the lamp itself. Please be sure to change
the lamp when is showing warning message.
When changing the lamp, please allow unit to cool down, and follow all
changing instructions.
Reset the "Lamp Hour Reset" function from the Onscreen display
"Management" menu after replacing the lamp module.
Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
vii
Caution for Listening
To protect your hearing, follow these instructions.
•
•
•
•
•
Increase the volume gradually until you can hear clearly and comfortably.
Do not increase the volume level after your ears have adjusted.
Do not listen to music at high volumes for extended periods.
Do not increase the volume to block out noisy surroundings.
Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
“Lamp(s) contain Mercury,
Dispose Properly.”
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org
viii
First things first
Usage Notes
Do:
•
Turn off the product before cleaning.
•
Use a soft cloth moistened with mild detergent to clean the display
housing.
•
Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
•
Block the slots and openings on the unit provided for ventilation.
•
Use abrasive cleaners, waxes or solvents to clean the unit.
•
Use under the following conditions:
•
•
•
•
In extremely hot, cold or humid environments.
In areas susceptible to excessive dust and dirt.
Near any appliance that generates a strong magnetic field.
Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
•
•
Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
•
•
Please do not open or disassemble the product as this may cause electric shock.
•
This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
•
Reset the "Lamp Hour Reset" function from the Onscreen display "Management"
menu after replacing the lamp module.
•
When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
•
•
•
Turn on the projector first and then the signal sources.
When changing the lamp, please allow unit to cool down, and follow all changing
instructions.
Do not use lens cap when projector is in operation.
When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
iii
First thing first
x
Usage Notes
x
Precautions
x
Introduction
1
Product Features
1
Package Overview
2
Projector Overview
3
Projector Outlook
3
Remote Control and Control Panel Layout
4
Getting Started
6
Connecting the Projector
6
Turning the Projector On/Off
7
Turning on the Projector
7
Turning off the Projector
8
Adjusting the Projected Image
9
Adjusting the Height of Projected Image
9
How to optimize image size and distance
10
How to get a preferred image size by adjusting
distance and zoom
12
User Controls
Installation menu
14
14
eMachines Empowering Technology
15
Onscreen Display (OSD) Menus
16
Color
17
Image
18
Setting
21
Management
23
Audio
23
Timer
24
Language
24
Appendices
25
Contents
Information for your safety and comfort
Troubleshooting
25
LED & Alarm Definition Listing
29
Replacing the Lamp
30
Ceiling Mount Installation
31
Specifications
34
Compatibility modes
36
Regulations and safety notices
40
1
Product Features
This product is a single-chip DLP® projector. Outstanding features include:
•
DLP® technology
•
Native 1280 x 720 720p resolution
4:3 / 16:9 / L.Box aspect ratio supported
•
eMachines ColorBoost technology delivers nature's true colors for vivid,
life-like images
•
High brightness and contrast ratio
•
Versatile display modes (Bright, Standard, Movie, Dark Cinema, Game,
Sports, User) for optimum performance in any situation
•
NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported
•
Lower power consumption and economy (ECO) mode extends lamp life
•
eMachines EcoProjeciton Technology delivers Intelligent power
management approach and physical efficiency improvement.
•
Empowering Key reveals eMachines Empowering Technology utilities
(eMachines eView, eTimer, ePower Management) for easy adjustment of
settings
•
Advanced digital keystone correction optimizes presentations
•
Multi-language onscreen display (OSD) menus
•
Manual focus projection lens zooms up to 1.1X
•
2X digital zoom and pan move function
•
Microsoft® Windows® 2000, XP, Vista®, Macintosh® OS compliant
English
Introduction
English
2
Package Overview
This projector comes with all the items shown below. Check to make sure your
unit is complete. Contact your dealer immediately if any thing is missing.
Projector with lens cap
Power cord
VGA cable
XXXXXX
3V
eMachines Projector
Security Card
Composite video cable
Battery
Security card
V700
V700
P/N: MU.JBD00.001
www.emachines.com
This CD contains:
• User Guide
• Acrobat Reader
Quick Start Guide
Cop
yright
© 2 00 9 . Al l r i g h t s r e s e r v
ed.
User’s guide
Carrying case
Remote control
Quick start guide
3
English
Projector Overview
Projector Outlook
Front / upper side
1
7
8
3
2
9
3
1
4
10
5
6
#
1
2
3
4
5
Description
#
Ventilation (inlet)
Ventilation (outlet)
Remote control receivers
Focus ring
Zoom lens
6
7
8
9
10
Description
Lens cap
Power button
Remote control
Zoom lever
Horn
Rear side
3
4
5
6
7
8
9
RS232
2
1
#
1
Description
Power socket
#
6
Description
YPbPr input connector
2
KensingtonTM lock port
7
S-Video input connector
3
4
RS232 connector
8
Composite video input connector
5
PC analog signal/HDTV/component video
9
input connector (VGA IN)
HDMI connector
Audio input connector
English
4
Remote Control and Control Panel Layout
2
1
8
3
9
8
4
#
Icon
5
6
10
11
7
12
2
13
Function
Description
1
Remote control
receiver
Receives signals from remote control.
2
POWER
Refer to the "Turning the Projector On/Off" section.
3
MENU
•
Press "MENU" to launch the Onscreen display (OSD)
menu, back to the previous step for the OSD menu
operation or exit the OSD menu.
•
Confirm your selection of items.
4
KeyPad 0~9
Press "0~9" to input a password in the "Security".
5
ASPECT RATIO
To choose the desired aspect ratio (Auto/4:3/16:9/L.Box).
6
RESYNC
Automatically synchronizes the projector to the input source.
7
FREEZE
To pause the screen image.
8
KEYSTONE
Adjusts the image to compensate for distortion caused by
tilting the projector (± 40 degrees).
9
Four directional Use up, down, left, right buttons to select items or make
select keys
adjustments to your selection.
10
ZOOM
Zooms the projector display in or out.
11
SOURCE
Changes the active source.
12
HIDE
Momentarily turns off the video. Press "HIDE" to hide the
image, press again to display the image.
5
Icon
Function
Empowering
key
Description
Unique eMachines functions: eView, eTimer, ePower
Management.
Note:
VZ.JBD00.001
Remote Control Placement
Please refer to the illustration to attach the remote control to the projector.
English
#
13
Getting Started
Connecting the Projector
VGA
DVD player
D-Sub
2
3
R B G
RS232
DVD player,
Set-top Box,
HDTV receiver
HDMI
D-Sub
4
6
5
HDMI
R
B
G
RS232
Y
1
9
7
S-Video Output
Y
8
R W
English
6
Video Output
#
Description
#
6
Description
1
Power cord
Audio cable jack/jack
2
RS232 cable
7
Audio cable Jack/RCA
3
VGA cable
8
Composite video cable
4
HDMI cable
9
S-Video cable
5
3 RCA component cable
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
7
Turning on the Projector
1
Remove the lens cap.(Illustration #1)
2
Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
3
Turn on the projector by pressing "Power" button on the control panel,
and the Power indicator LED will turn blue. (Illustration #2)
4
Turn on your source (computer, notebook, video player ,etc.). The
projector will detect your source automatically.
•
If the screen displays "Lock" and "Source" icons, it means the
projector is locked onto a specific source type and there is no such
type of input signal detected.
•
If the screen displays "No Signal", please make sure the signal cables
are securely connected.
•
If you connect to multiple sources at the same time, use the "Source"
button on the remote control to switch between inputs.
2
Power button
1
Lens cap
English
Turning the Projector On/Off
English
8
Turning off the Projector
1
To turn off the projector, press the "Power" button twice. The message
below will display onscreen for 5 seconds.
"Please press power button again to complete the shutdown process."
2
Immediately after powering off, the Power indicator LED will flash RED
rapidly and the fan(s) will continue to operate for about 120 seconds. This
is to ensure that the system cools correctly.
3
Once the system has finished cooling, the Power indicator LED will turn
solid RED which means projector enter standby mode.
4
It is now safe to unplug the power cord.
Warning: Do not turn on the projector immediately after
powering off.
Note: If you wish to turn the projector back on, you must wait for
60 seconds at least to press the "Power" button to restart the
projector.
Warning indicators:
•
If the projector automatically shuts down and the Power indicator
quick flashing RED and steady BLUE by returns, please contact your
local reseller or service center.
•
If the projector automatically shuts down and the Power indicator
quick flashing RED and steady BLUE by returns, this indicates that the
projector has overheated. The message below will display onscreen if
this is about to happen:
"Projector Overheated. Lamp will automatically turn off soon."
•
If the Power indicator quick flashing RED and steady BLUE by returns
and the message below is displayed onscreen, please contact your
local dealer or service center:
"Fan fail. Lamp will automatically turn off soon."
9
Adjusting the Height of Projected Image
The projector is equipped with elevator feet for adjusting the height of image.
To raise/lower the image:
1
Use Tilt adjusting wheel (Illustration #1) to fine-tune the display angle.
1
Tilt adjusting wheel
English
Adjusting the Projected Image
English
10
How to optimize image size and distance
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen. Example: If the
projector is 3 m from the screen, good image quality is possible for image sizes
between 80" and 87".
Note: Remind as below figure, the space of 122 cm height is
required when located at 3m distance.
Max
scree
n size
Min s
creen
size
B
87"
80"
Height: 122cm
Form base to
top of image
Height:
112cm
C
A
3m
Desired Distance
Figure: Fixed distance with different zoom and screen size.
11
(Min zoom)
W (cm) x
H (cm)
Top
Screen size
(Max zoom)
From base to Diagonal
top of image
(inch)
<B>
(cm) <C>
W (cm) x
H (cm)
From base to top
of image (cm)
<C>
41
1
27
59 x 33
37
29
65 x 36
1.5
40
88 x 50
56
44
97 x 54
61
2
53
118 x 66
74
58
129 x 73
82
2.5
66
147 x 83
93
73
161 x 91
102
3
80
176 x 99
112
87
194 x 109
122
3.5
93
206 x 116
130
102
226 x 127
143
4
106
235 x 132
149
117
258 x 145
163
4.5
120
265 x 149
167
131
290 x 163
184
5
133
294 x 165
186
146
323 x 181
204
6
159
353 x 199
223
175
387 x 218
245
7
186
412 x 232
260
204
452 x 254
286
8
213
471 x 265
298
233
516 x 290
326
9
239
529 x 298
335
262
581 x 327
367
10
266
588 x 331
372
291
645 x 363
408
10.3
274
606 x 341
383
300
665 x 374
420
Zoom Ratio: 1.1x
English
Top
Screen size
Desired
Distance
(m)
Diagonal
<A>
(inch)
<B>
English
12
How to get a preferred image size by adjusting
distance and zoom
A
50"
Desir
e
imag d
es
ize
D
Height
Form base to
top of image
1.7 m
1.9 m
C
B
Desired Distance
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring. Example: to obtain an image size of 50" set the
projector at a distance 1.7 m and 1.9 m from the screen and adjust the zoom
level accordingly.
13
Distance (m)
Top (cm)
Diagonal (inch)
<A>
W (cm) x H (cm)
Max zoom
<B>
Min zoom
<C>
30
66 x 37
1.0
1.1
From base to top of
image
<D>
42
40
89 x 50
1.4
1.5
56
50
111 x 62
1.7
1.9
70
60
133 x 75
2.1
2.3
84
70
155 x 87
2.4
2.6
98
80
177 x 100
2.7
3.0
112
90
199 x 112
3.1
3.4
126
100
221 x 125
3.4
3.8
140
120
266 x 149
4.1
4.5
168
150
332 x 187
5.1
5.6
210
180
398 x 224
6.2
6.8
252
200
443 x 249
6.9
7.5
280
250
553 x 311
8.6
9.4
350
300
664 x 374
10.3
***
420
Zoom Ratio: 1.1x
English
Desired Image Size
English
14
User Controls
Installation menu
The installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No signal
input" is displayed on the screen.
The menu options include settings and adjustments for screen size and distance,
focus, keystone correction and more .
1
Turn on the projector by pressing "Power" button on the control pad.
2
Press the "MENU" button on the control pad to launch the OSD for
projector installation and maintenance.
3
The background pattern acts as a guide to adjusting the calibration and
alignment settings, such as screen size and distance, focus and more .
4
The Installation menu includes the following options:
•Projection method
•Projection location
•Menu location
•Keystone settings
•Language settings
•Reset to factory default function
Use the up and down arrow keys to select an option, the left and right
arrow keys to adjust selected option settings, and the right arrow key to
enter a submenu for feature setting. The new settings will be saved
automatically upon exiting the menu.
5
Push the menu button anytime to exit the menu and return to the
eMachines welcome screen.
15
Empowering
Key
eMachines eView
Management
eMachines Empowering Key provide
three eMachines unique functions, they
are "eMachines eView Management",
"eMachines eTimer Management" and
"eMachines ePower Management"
respectively. Press "
" key for more
than one second to launch the
Onscreen display main menu to modify
its function.
Press "
" to launch "eMachines
eView Management" submenu.
"eMachines eView Management" is for
display mode selection. Please refer to
Onscreen Display Menus section for
more detail.
eMachines eTimer
Management
Press "
" to launch "eMachines
eTimer Management" submenu.
"eMachines eTimer Management"
provides the reminding function for
presentation time control. Please refer
to Onscreen Display Menus section for
more detail.
eMachines ePower
Management
Press "
" to launch "eMachines
ePower Management".
"eMachines ePower Management"
provides user one shortcut to save lamp
and projector life. Please refer to
Onscreen Display section for more
detail.
English
eMachines Empowering Technology
English
16
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allow you to make image adjustments
and change a variety of settings.
Using the OSD menus
•
To open the OSD menu, press "MENU" on the remote control.
•
When the OSD is displayed, use the
keys to select any item in the
main menu. After selecting the desired main menu item, press
submenu for feature setting.
•
Use the
using the
to enter
keys to select the desired item and adjust the settings by
keys.
•
Select the next item to be adjusted in the submenu and adjust as described
above.
•
Press "MENU" on the remote control, the screen will return to the main
menu.
•
To exit OSD, press "MENU" on the remote control again. The OSD menu
will close and the projector will automatically save the new settings.
Main menu
Setting
Sub menu
17
Display Mode
English
Color
There are many factory presets optimized for various types of
images.
•
•
•
•
•
•
•
Bright: For brightness optimization.
Standard: For common environment.
Movie: For brighter and general movie/video/photo playing.
Dark Cinema: For dark movie content.
Game: For game content.
Sports: For sport picture.
User: Memorize user’s settings.
Wall color
Use this function to choose a proper color according to the wall.
There are several choices, including white, light yellow, light blue,
pink, dark green. It will compensate the color deviation due to the
wall color to show the correct image tone.
Brightness
Adjust the brightness of the image.
Contrast
•
Press
to darken image.
•
Press
to lighten the image.
"Contrast" controls the difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
•
Press
to decrease the contrast.
•
Press
to increase the contrast.
Color
Temperature
Adjust the color temperature. At higher color temperatures, the
screen looks colder; at lower color temperatures, the screen looks
warmer.
Degamma
Effects the representation of dark scenery. With greater gamma
value, dark scenery will look brighter.
Color R
Adjusts the red color.
Color G
Adjusts the green color.
Color B
Adjusts the blue color.
English
18
Saturation
Adjusts a video image from black and white to fully saturated
color.
Tint
•
Press
to decrease the amount of color in the image.
•
Press
to increase the amount of color in the image.
Adjusts the color balance of red and green.
•
Press
to increase the amount of green in the image.
•
Press
to increase the amount of red in the image.
Note: "Saturation" and "Tint" functions are not supported under computer
mode or DVI mode.
Image
Projection mode
•
Front: The factory default setting.
•
Rear: Reverses the image so you can project from behind a
translucent screen.
•
Auto: Automatically adjusts projection location of image.
•
Desktop
•
Ceiling: Turns the image upside down for ceiling-mounted
projection.
Projection Location
19
Use this function to choose your desired aspect ratio.
Auto: Keep the image with original width-higth ratio and maxi
mize the image to fit native horizontal or vertical pixels.
•
4:3: The image will be scaled to fit the screen and displayed using
a 4:3 ratio.
•
16:9: The image will be scaled to fit the width of the screen and
the height adjusted to display the image using a 16:9 ratio.
•
Auto Keystone
Automatically adjusts vertical image.
Manual Keystone
Adjust image distortion caused by tilting projection. (±40 degrees)
<Note> The Manual Keystone funcion is unavailable under Auto
Keystone setting to "On".
H. Position
(Horizontal
position)
•
Press
to move the image left.
•
Press
to to move the image right.
V. Position
(Vertical position)
•
Press
to move the image down.
•
Press
to move the image up.
Frequency
"Frequency" changes the projector's refresh rate to match the
frequency of your computer’s graphics card. If you can see a vertical
flickering bar in the projected image, use this function to make the
necessary adjustments.
Tracking
Synchronizes the signal timing of the projector with the graphics card.
If you experience an unstable or flickering image, use this function to
correct it.
Sharpeness
3D
3D Sync L/R
Adjusts the sharpness of the image.
•
Press
to decrease the sharpness.
•
Press
to increase the sharpness.
Choose "On" to enable 3D function supported by NVIDIA or TI DLP 3D
technology.
•
On: Choose this item while using DLP 3D glasses, quad buffer
(NVIDIA/ATI...) graphic card and HQFS format file or DVD with
corresponding SW player.
•
Off: Turn off 3D mode.
If you see a discrete or overlapping image while wearing DLP 3D
glasses, you may need to execute "Invert" to get best match of left/
right image sequence to get the correct image (for DLP 3D).
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under DVI or Video mode.
Note: "Sharpness" functions is not supported under DVI and Computer
mode.
Note: It needs correct settings on graphic card 3D application program for
correct 3D display.
Note: The SW players, such as Stereoscopic Player and DDD TriDef Media
Player can support 3D format files. You can download these three players
on web page below,
English
Aspect Ratio
English
20
- NVIDIA Stereoscopic 3D Video Player:
http://www.nvidia.com/object/3D_Drivers_Downloads.html
- Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx
- DDD TriDef Media Player (Trial):
http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html
Note: "3D Sync L/R" is only available when 3D is enabled.
Note: There has reminder screen if 3D still enable when power on projector.
Please adjust setting depended on your purpose.
21
English
Setting
Menu Location
Choose the menu location on the display screen.
Source Lock
When source lock is turned "off", the projector will search for
other signals if the current input signal is lost. When source lock is
turned "on", it will "lock" the current source channel unless you
press "Source" button on the remote control for the next channel.
Closed Caption
Selects a preferred closed captioning mode from CC1, CC2, CC3,
CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only
available when a composite video or S-Video input signal is
selected and its system format is NTSC.
<Note> This function is not available when the aspect ratio is
"16:9" or 16:9 format detected under "Auto mode"..
Security
Security
This projector provides a useful security function for the
administrator to manage usage of the projector .
Press
to change the "Security" setting. If the security function
is enabled, your must enter the "Administrator Password" first
before changing the security settings.
•
Select "On" to enable the security function. The user has to
enter a password to operate the projector. Please refer to the
"User Password" section for details.
•
If "Off" is selected, then the user can turn on the projector
without password.
Timeout(Min.)
Once "Security" is activated to "On", the administrator can set
timeout function.
•
Press
•
•
The range is from 10 minute to 990 minutes.
•
•
The factory default setting of "Timeout(Min.)" is "Off".
or
to select the timeout interval.
When the time is up, the projector will prompt the user to
enter the password again.
Once the security function is enabled, the projector will
request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be
accepted for this dialogue.
22
English
User password
•
•
Press
•
Press
•
Enter the password when you see "Confirm Password"
displayed.
•
•
The password should be between 4 and 8 characters long.
•
If you select "Always request password while projector turns
on", the user has to enter the password every time when the
projector is turned on.
to setup or change the "User Password".
Press number keys to set your password on the remote control
and press "MENU" to confirm.
to delete character.
If you select "Request password only after plugging power
cord", the projector will prompt the user to enter the
password every time the power cord is plugged.
Administrator Password
The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.
•
•
Press
to change the "Administrator Password".
The factory default of "Administrator Password" is "1234".
If you forgot your administrator password, do the following to
retrieve the administrator password:
Reset
•
An unique 6-digit "Universal Password" which is printed on
the Security Card (please check accessory in the box). This
unique password is the number which will be accepted by
projector anytime no matter what the Administrator
Password is.
•
If losing this security card and number, please contact with an
eMachines service center.
•
Press the
button and choose "Yes" to return the
parameters on all menus to the factory default settings.
23
English
Management
ECO Mode
Choose "On" to dim the projector lamp which will lower power
consumption, extend the lamp life and reduce noise. Choose "Off"
to return normal mode.
High Altitutde
Choose "On" to turn on High Altitude mode. Operate the fans at
full speed continuously to allow for proper high altitude cooling of
the projector.
Auto Shutdown
The projector will automatically shutdown when there is no signal
input after the allocated time. (in minutes)
Lamp Hour Elapse
Displays the lamp’s elapsed operating time (in hours).
Lamp Reminding
Activate this function to display a reminder to change the lamp 30
hours before its expected end-of-life.
Lamp Hour Reset
Press the
button and choose "Yes" to turn the lamp hour
counter to 0 hours.
Audio
Volume
•
Press
to decrease the volume.
•
Press
to increase the volume.
Choose "On" to mute the volume.
Choose "Off" to restore the volume.
Power On/Off Volume
•
•
•
Alarm Volume
•
Select this function to adjust the volume of any warning
votifications.
Mute
Select this function to adjust the notification volume when
turning the projector on/off.
English
24
Timer
Timer Location
•
Choose the location of the timer on the screen.
Timer Start
•
Press
to start or stop the timer.
Timer Period
•
Press
or
Timer Volume
•
Select this function to adjust the nitification volume when
the timer function is enabled and time is up.
Timer Display
•
Press
or
to adjust the timer period.
to which timer mode to display on the
screen.
Language
Language
Choose the multilingual OSD menu. Use the
to select your preferred menu language.
•
Press
to confirm the selection.
or
key
25
English
Appendices
Troubleshooting
If you experience a problem with your eMachines projector, refer to the
following troubleshooting guide. If the problem persists, please contact your
local reseller or service center.
Image Problems and Solutions
#
1
2
Problem
No image appears
onscreen
Partial, scrolling
or incorrectly
displayed
image(For PC
(Windows 95/98/
2000/XP))
Solution
•
Connected as described in the "Getting Started"
section.
•
Ensure none of the connector pins are bent or
broken.
•
Check if the projector lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
•
Make sure you have removed the lens cap and the
projector is switched on.
•
•
Press "RESYNC" on the remote control.
For an incorrectly displayed image:
•
Open "My Computer," open the "Control
Panel," and then double-click the "Display"
icon.
•
Select the "Settings" tab.
•
Verify that your display resolution setting is
lower than or equal to UXGA (1600 x 1200).
•
Click the "Advanced Properties" button.
If the problem still appears, change the monitor display
you are using and follow the steps below:
•
Verify that the resolution setting is lower than
or equal to UXGA (1600 x 1200).
•
Click the "Change" button under the
"Monitor" tab.
•
Click "Show all devices". Next, select "Standard
monitor types" under the SP box, and choose
the resolution mode you need under the
"Models" box.
•
Verify that the resolution setting of the
monitor display is lower than or equal to UXGA
(1600 x 1200).
English
26
3
4
5
6
7
8
Partial, scrolling
or incorrectly
displayed image
(For notebooks)
The screen of the
notebook
computer is not
displaying your
presentation
Image is unstable
or flickering
Image has vertical
flickering bar
Image is out of
focus
Image is stretched
when displaying a
"widescreen"
DVD title
•
•
Press "RESYNC" on the remote control.
•
If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment
including the projector.
•
If you are using a Microsoft® Windows® based
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
•
If you are using an Apple® Mac® OS based
notebook: In System Preferences, open Display and
select Video Mirroring "On".
•
Adjust the "Tracking" to correct it. Refer to the
"Image" section for more information.
•
Change the display color depth settings on your
computer.
•
Use "Frequency" to make an adjustment. Refer to
the "Image" section for more information.
•
Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
•
•
•
Make sure the lens cap is removed.
For an incorrectly displayed image:
•
Follow the steps for item 2 (above) to adjust
the resolution of your computer.
•
Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP
[Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5 ]
Adjusts the focus ring on the projector lens.
Make sure the projection screen is within the
required distance of 3.3 to 33.8 feet (1.0 to 10.3
meters) from the projector. Refer to the "How to
Get a Preferred Image Size by Adjusting Distance
and Zoom" section for more information.
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:
•
If you play a 4:3 format DVD title, please change the
format to 4:3 in the projector OSD.
•
If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
27
10
11
Image is too small
or too large
Image has slanted
sides
Image is reversed
•
•
Adjust the zoom lever on the front of the projector.
•
Press "MENU" on the remote control. Go to "Image
--> Aspect Ratio" and try different settings or
press"Aspect Ratio" on the remote control to adjust
directly.
•
If possible, reposition the projector so that it is
centered on the screen.
•
Press the "Keystone / " button on the remote
control until the sides are vertical.
•
Press "MENU" on the remote control. Go to "Image -> Auto Keystone" and choose "Off" on the OSD, if
"Keystone" button is not available on the remote
control.
•
Select "Image --> Projection" on the OSD and adjust
the projection direction.
Move the projector closer to or further from the
screen.
Problems with the Projector
#
Condition
Solution
1
The projector stops responding
to all controls
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
2
Lamp burns out or makes a
popping sound
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
English
9
English
28
OSD Messages
#
1
Condition
Message
Message Reminder
Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed to
cool down before it may be used.
Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
29
English
LED & Alarm Definition Listing
LED Messages
Power LED
Message
Red
Blue
Flash ON to OFF 100ms
--
Standby
V
--
Power button ON
--
V
Lamp retry
--
Quick Flashing
Quick Flashing
--
V
--
Input Power Plug
Power off (Cooling state)
Power button OFF:
Cooling completed;
Standby Mode
Error (Thermal Failure)
Quick Flashing RED and Steady BLUE by returns
Error (Fan lock)
Quick Flashing RED and Steady BLUE by returns
Error (Lamp breakdown)
Quick Flashing BLUE and Steady RED by returns
Error (Color Wheel fail)
Quick Flashing BLUE and Steady RED by returns
English
30
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.
The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement Suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooling down for at least 30
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool down
before changing the lamp.
1
3
2
4
To Change the Lamp
1
Turn off the projector by pressing the Power button.
2
Allow the projector at least 30 mins to cool down.
3
Disconnect the power cord.
4
Use a screwdriver to remove the screw from the cover. (Illustration #1)
5
Push up and remove the cover.
6
Remove the two screws that secure the lamp module (Illustration #2) and
pull up the lamp bar.(Illustration #3)
7
Pull out the lamp module by force. (Illustration #4)
To replace the lamp module, reverse the previous step.
Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
31
If you wish to install the projector using a ceiling mount, please refer to the
steps below:
Drill four holes into a solid, structurally sound part of the ceiling, and
secure the mount base.
m
m
m
13 m
20
1
mm
130 mm
8.4
.9
49mm
Note: Screws are not included. Please obtain the appropriate
screws for your type of ceiling.
2
Secure the ceiling rod using the appropriate type of four-cylinder screws.
Ceiling Mount Base
- Attach to ceiling
Short Rod
Long Rod
Extension Rod
Screw Type A
50 mm length / 8 mm diameter -
Long Cylinder Cap
Allen Key
- For tightening/looseni
Tightening Screw
Medium Rod
English
Ceiling Mount Installation
English
32
3
Use the appropriate number of screws for the projector size to attach the
projector to the ceiling mount bracket.
Screw Type B
Smaller Washer
Large Washer
Projector Bracket
Supports projector and allows for adjustments
Spacer
- For heat dissipation
Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution. Use two washers for extra support, if deemed
necessary.
4
Attach the ceiling bracket to the ceiling rod.
Large cylinder cap
Allen Key
Screw Type A
50 mm length 08 mm diameter
- For tightening/loosening
Tightening Screw
33
Adjust the angle and positioning as necessary.
English
5
Tightening Screw
Allen Key
3
Allen Key
Tightening Screw
Note: The appropriate type of screw and washer for each model is
listed in the table below. 3 mm diameter screws are enclosed in
the screw pack.
Models
Washer Type
Length (mm)
Large
Small
3
25
V
V
SCREW SPEC. M3 x 25 mm
82.30 mm
V700
Screw Type B
Diameter (mm)
95.00 mm
15.00 mm
English
34
Specifications
The specifications listed below are subject to change without notice. For final
specs, please refer to eMachines's published marketing specifications.
Projection system
DLP®
Resolution
V700: Native: 720P (1280 x 720) , Maximum: UXGA
(1600 x 1200), WSXGA+ (1680x1050),
1080p(1920x1080)
Computer compatibility
IBM PC and compatibles, Apple Macintosh, iMac and
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA +
Video compatibility
NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p,
576p), SDTV (480i, 576i)
Aspect ratio
Auto, 4:3, 16:9, L.Box
Displayable colors
1.07 Billion colors
Projection lens
F/ 2.5 - 2.67, f = 21.86 mm - 24.00 mm, 1.1X manual
zoom lens
Projection screen size (diagonal)
27" (0.69m) - 300" (7.62 m)
Projection distance
3.3' (1.0 m) - 33.8' (10.3 m)
Throw ratio
58"@2m (1.55 - 1.70:1)
Horizontal scan rate
30k - 100 kHz
Vertical refresh scan rate
50-85 Hz, 120Hz (for 3D mode only)
Lamp type
200W user-replaceable lamp
Keystone correction
± 40 degrees
Audio
Internal speaker with 2 W output
Weight
2.26 Kg (4.9 lbs.)
Dimensions (W x D x H)
268 mm x 192 mm x 80 mm (10.6" x 7.6" x 3.1")
Digital Zoom
2X
Power supply
AC input 100 - 240 V auto-switching power supply
Power consumption
248W ± 10% for normal mode
201W ± 10% for ECO mode
Operating temperature
5ºC to 35ºC / 41ºF to 95ºF
I/O connectors
•
•
•
•
•
•
•
•
Power socket x1
VGA input x1
RS232 x1
Composite video x1
S-Video x1
3 RCA Component video x1
HDMI x1
3.5 mm audio jack input x1
35
•
•
•
•
•
•
•
•
•
•
AC power cord x1
VGA cable x1
Composite video cable x1
Remote control x1
Battery x1 (for remote control)
User's guide (CD-ROM) x1
Quick start guide x1
Security card x1
Carrying case x1
HDMI cable x1
* Design and specifications are subject to change without notice.
English
Standard package contents
English
36
Compatibility modes
A. VGA Analog
1
VGA Analog - PC Signal
Modes
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
VGA
640x480
60
31.47
640x480
72
37.86
640x480
75
37.50
SVGA
XGA
SXGA
QuadVGA
640x480
85
43.27
640x480
119.51
61.60
800x600
56
35.20
800x600
60
37.88
800x600
72
48.08
800x600
75
46.88
800x600
85
53.67
800x600
119.85
77.20
1024x768
60
48.36
1024x768
70
56.48
1024x768
75
60.02
1024x768
85
68.67
1024x768
119.804
98.80
1152x864
70
63.80
1152x864
75
67.50
1152x864
85
77.10
1280x1024
60
63.98
1280x1024
72
77.90
1280x1024
75
79.98
1280x1024
85
91.15
1280x960
60
60.00
1280x960
75
75.00
SXGA+
1400x1050
60
65.32
UXGA
1600x1200
60
75.00
PowerBook G4
640x480
60
31.50
PowerBook G4
640x480
66.6(67)
35.00
PowerBook G4
800x600
60
37.88
PowerBook G4
1024x768
60
48.36
PowerBook G4
1152x870
75
68.68
PowerBook G4
1280x960
75
75.20
i Mac DV(G3)
1024x768
75
60.30
37
VGA Analog - Extended Wide timing
Modes
WXGA
WXGA+
WSXGA
3
Resolution
1280x768
1280x768
1280x768
1280x720
1280x720
1280x800
1366x768
1440x900
1680x1050
1920x1080-RB
1920x1080-EIA
1024x600
V.Frequency [Hz]
60
75
85
60
119.858
60
60
60
60
60
60
60
H.Frequency [KHz]
47.78
60.29
68.63
44.80
92.89
49.60
47.71
55.90
65.30
66.60
66.60
37.30
VGA Analog -Component Signal
480i
480p
576i
576p
720p
720p
1080i
1080i
1080p
1080p
720x480
720x480
720x576
720x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
59.94(29.97)
59.94
50(25)
50
60
50
60(30)
50(25)
60
50
27.00
31.47
27.00
31.25
45.00
37.50
33.75
33.75
67.50
56.26
B. HDMI Digital
(1) HDMI - PC Signal(same as DVI)
Modes
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
VGA
640x480
60
31.47
640x480
72
37.86
640x480
75
37.50
SVGA
XGA
640x480
85
43.27
640x480
119.51
61.61
800x600
56
35.20
800x600
60
37.88
800x600
72
48.08
800x600
75
46.88
800x600
85
53.67
800x600
119.85
77.20
1024x768
60
48.36
English
2
English
38
SXGA
1024x768
70
56.48
1024x768
75
60.02
1024x768
119.804
98.80
1152x864
70
67.50
1152x864
85
77.10
1280x1024
60
64.00
1280x1024
72
77.90
1280x1024
75
79.98
1280x1024
85
91.15
QuadVGA
1280x960
75
75.00
PowerBook G4
640x480
60
31.50
PowerBook G4
640x480
66.6(67)
35.00
PowerBook G4
800x600
60
37.88
PowerBook G4
1024x768
60
48.36
PowerBook G4
1152x870
75
68.68
PowerBook G4
1280x960
75
75.20
i Mac DV(G3)
1024x768
75
60.30
(2) HDMI - Extended Wide timing(same as DVI)
Modes
WXGA
WXGA+
WSXGA
Resolution
1280x768
1280x768
1280x768
1280x720
1280x720
1280x800
1366x768
1440x900
1680x1050
1920x1080-RB
1920x1080-EIA
1024x600
V.Frequency [Hz]
60
75
85
60
119.858
60
60
60
60
60
60
60
H.Frequency [KHz]
47.78
60.29
68.63
44.80
92.89
49.60
47.71
55.90
65.30
66.60
66.60
37.30
(3) HDMI - Video Signal
480i
720x480
59.94(29.97)
27.00
480p
720x480
59.94
31.47
27.00
576i
720x576
50(25)
576p
720x576
50
31.25
720p
1280x720
60
45.00
720p
1280x720
50
37.50
1080i
1920x1080
60(30)
33.75
39
1920x1080
50(25)
33.75
1920x1080
60
67.50
1080p
1920x1080
50
56.26
Horizontal scan rate:
Graphic source moniVertical scan rate:
tor range limits
Max. pixel rate:
30-100kHz
50-85 Hz, 120Hz (for 3D mode only)
170MHz
English
1080i
1080p
English
40
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the device and receiver.
•
Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.
Caution
Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
Radio device regulatory notice
Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio
communication devices (RSS-210)
a
Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
b
Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact the local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.
English
Remarque à l'intention des utilisateurs canadiens
English
41
Acer Incorporated
8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih
Taipei Hsien 221, Taiwan
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan
Contact Person: Mr. Easy Lai, e-mail:easy_lai@acer.com.tw
And,
Acer Europe SA
Via Cantonale, Centro Galleria 2 6928 Manno Switzerland
Hereby declare that:
Product:
Trade Name:
Model Number:
Machine Type:
Projector
eMachines
H7P0901
V700
Is compliant with the essential requirements and other relevant provisions of the following EC
directives, and that all the necessary steps have been taken and are in force to assure that
production units of the same product will continue comply with the requirements.
EMC Directive 2004/108/EC as attested by conformity with the following
harmonized standards:
-. EN55022, AS/NZS CISPR22, Class B
-. EN55024
-. EN61000-3-2 Class A
-. EN61000-3-3
Low Voltage Directive 2006/95/EC as attested by conformity with the following
harmonized standard:
-. EN60950-1
RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous
Substances in Electrical and Electronic Equipment
-. The maximum concentration values of the restricted substances by weight in homogenous
material are:
Lead
Mercury
Hexavalent Chromium
!
0.1%
0.1%
0.1%
Polybrominated Biphenyls (PBB’s)
Polybrominated Diphenyl Ethers (PBDE’s)
Cadmium
0.1%
0.1%
0.01%
Directive 2009/125/EC with regard to establishing a framework for the setting
of ecodesign requirements for energy-related product.
Acer Incorporated
8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih
Taipei Hsien 221, Taiwan
The standards listed below are applied to the product if built with WLAN
module or wireless keyboard and mouse.
R&TTE Directive 1999/5/EC as attested by conformity with the following
harmonized standard:
z Article 3.1(a) Health and Safety
-. EN60950-1
-. EN62311
z Article 3.1(b) EMC
-. EN301 489-1
-. EN301 489-17
z Article 3.2 Spectrum Usages
-. EN300 328
-. EN301 893 (Applicable to 5GHz high performance RLAN).
Year to begin affixing CE marking 2010.
_______________________________
Mar. 1, 2010
Easy Lai /Manager
Date
Regulation Center, Acer Inc.
-
Acer America Corporation
333 West San Carlos St., San Jose
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product:
DLP Projector
Model Number:
H7P0901
Machine Type:
V700
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party:
333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147
Download PDF