Zhone | 4821-A2 | Installation guide | Zhone 4821-A2 Installation guide

BitStorm® 4800 Express
Model 4821-A2
Installation Guide
Document No. 4821-A2-GN21-10
July 2004
Copyright © 2004 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or
by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express
written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.
Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for any help needed. For additional
information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or
Paradyne worldwide office locations, use one of the following methods:
„
Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at
www.paradyne.com/warranty.)
„
Telephone: Call our automated system to receive current information by fax or to speak with a company
representative.
—
Within the U.S.A., call 1-800-870-2221
—
Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them to Technical Publications,
Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the
number and title of this document in your correspondence. Please include your name and phone number if you are
willing to provide additional clarification.
Trademarks
ACCULINK, BitStorm, COMSPHERE, FrameSaver, Hotwire, Jetstream, MVL, NextEDGE, OpenLane, Performance
Wizard are registered trademarks of Paradyne Corporation. EtherLoop, GranDSLAM, GrandVIEW, iMarc, ReachDSL,
StormTracker, and TruePut are trademarks of Paradyne Corporation. All other products and services mentioned herein
are the trademarks, service marks, registered trademarks, or registered service marks of their respective owners.
A
July 2004
4821-A2-GN21-10
Software and Firmware License Agreement
ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS, YOU MAY USE THE
SOFTWARE AND/OR FIRMWARE INCORPORATED INTO THE PARADYNE PRODUCT. BY USING THE
PARADYNE PRODUCT YOU SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS LICENSE AGREEMENT,
PROMPTLY RETURN THE UNUSED PRODUCT IN ITS ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR
INVOICE TO THE LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE LOCATION FROM
WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU WILL RECEIVE A REFUND OR CREDIT FOR
THE PARADYNE PRODUCT PURCHASED BY YOU.
The terms and conditions of this License Agreement (the “Agreement”) will apply to the software and/or
firmware (individually or collectively the “Software”) incorporated into the Paradyne product (the “Product”)
purchased by you and any derivatives obtained from the Software, including any copy of either. If you have
executed a separate written agreement covering the Software supplied to you under this purchase, such
separate written agreement shall govern.
Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept a personal,
non-transferable, non-exclusive, right (without the right to sublicense) to use the Software, solely as it is
intended and solely as incorporated in the Product purchased from Paradyne or its authorized distributor or
reseller under the following terms and conditions:
1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The Licensee acquires
no title, right or interest in the Software other than the license granted under this Agreement.
2. Licensee shall not use the Software in any country other than the country in which the Product was
rightfully purchased except upon prior written notice to Paradyne and an agreement in writing to
additional terms.
3. The Licensee shall not reverse engineer, decompile or disassemble the Software in whole or in part.
4. The Licensee shall not copy the Software except for a single archival copy.
5. Except for the Product warranty contained in the manual, the Software is provided “AS IS” and in its
present state and condition and Paradyne makes no other warranty whatsoever with respect to the
Product purchased by you. THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER
WARRANTIES, WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING
WITHOUT LIMITATION:
a. Any warranty that the Software is error-free, will operate uninterrupted in your operating
environment, or is compatible with any equipment or software configurations; and
b.
ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NON-INFRINGEMENT.
Some states or other jurisdictions do not allow the exclusion of implied warranties on limitations on how
long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from one state or jurisdiction to
another.
6. In no event will Paradyne be liable to Licensee for any consequential, incidental, punitive or special
damages, including any lost profits or lost savings, loss of business information or business interruption
or other pecuniary loss arising out of the use or inability to use the Software, whether based on
contract, tort, warranty or other legal or equitable grounds, even if Paradyne has been advised of the
possibility of such damages, or for any claim by any third party.
4821-A2-GN21-10
July 2004
B
7. The rights granted under this Agreement may not be assigned, sublicensed or otherwise transferred by
the Licensee to any third party without the prior written consent of Paradyne.
8. This Agreement and the license granted under this Agreement shall be terminated in the event of
breach by the Licensee of any provisions of this Agreement.
9. Upon such termination, the Licensee shall refrain from any further use of the Software and destroy the
original and all copies of the Software in the possession of Licensee together with all documentation
and related materials.
This Agreement shall be governed by the laws of the State of Florida, without regard to its provisions
concerning conflicts of laws.
! Important Safety Instructions
1. Read and follow all warning notices and instructions marked on the product or included in the manual.
2. This product is intended to be used with a 3-wire grounding type plug — a plug that has a grounding pin. This is a
safety feature. Equipment grounding is vital to ensure safe operation. Do not defeat the purpose of the grounding
type plug by modifying the plug or using an adapter. Prior to installation, use an outlet tester or a voltmeter to check
the AC receptacle for the presence of earth ground. If the receptacle is not properly grounded, the installation must
not continue until a qualified electrician has corrected the problem.
If a 3-wire grounding type power source is not available, consult a qualified electrician to determine another
method of grounding the equipment.
3. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to
protect it from overheating, these slots and openings must not be blocked or covered.
4. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power
cord.
5. Do not attempt to service this product yourself, as it will void the warranty. Opening or removing covers may expose
you to dangerous high voltage points or other risks. Refer all servicing to qualified service personnel.
6. General purpose cables are described for use with this product. Special cables, which may be required by the
regulatory inspection authority for the installation site, are the responsibility of the customer. To reduce the risk of
fire, use a UL Listed or CSA Certified, minimum No. 26 AWG (0.128 mm2) telecommunication cable, or
comparable cables certified for use in the country of installation.
7. When installed in the final configuration, the product must comply with the applicable Safety Standards and
regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory
agencies and inspection authorities to ensure compliance.
8. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If products
installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition. Consult
a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary, implement
corrective action prior to interconnecting the products.
9. In addition, if the equipment is to be used with telecommunications circuits, take the following precautions:
C
—
Never install telephone wiring during a lightning storm.
—
Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
—
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface.
—
Use caution when installing or modifying telephone lines.
—
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of
electric shock from lightning.
—
Do not use the telephone to report a gas leak in the vicinity of the leak.
July 2004
4821-A2-GN21-10
10. CLASS 1 LASER PRODUCT: This product has provisions for the customer to install a Class 1 laser transciever,
which provides optical coupling to the telecommunication network. Once a Class 1 laser product is installed, the
equipment is to be considered to be a Class 1 Laser Product (Appareil à Laser de Classe 1). The customer is
responsible for selecting and installing the laser transciever and for insuring that the Class 1 AEL (Allowable
Emission Limit) per EN/IEC 60825 is not exceeded after the laser transponders have been installed. Do not install
laser products whose class rating is greater than 1. Refer to all important safety instructions that accompanied the
transciever prior to installation. Only laser Class 1 devices, certified for use in the country of installation by the
cognizant agency are to be utilized in this product.
11. The equipment is intended for installation in a max. 50° C ambient temperature, in an environment that is free of
dust and dirt.
12. The power supply cord for countries other than North America is to be a minimum H05 V V-F type, min. 0.75 mm2,
2-conductor and earth ground terminated in an IEC 320 connector on one end, and a plug which is certified for use
in the country of installation at the other end.
13. Do not physically stack more than eight (8) 26x1 units high. Physical stability has not been evaluated for stacking
higher than eight units, and any configuration greater than eight may result in an unstable (tip-over) condition.
Ensure that the four (4) rubber feet supplied with the product have been installed on the bottom of each unit prior to
stacking any 26x1 units on top of one another.
EMI Notices
! UNITED STATES – EMI NOTICE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
The authority to operate this equipment is conditioned by the requirements that no modifications will be
made to the equipment unless the changes or modifications are expressly approved by Paradyne
Corporation.
If the equipment includes a ferrite choke or chokes, they must be installed per the installation instructions.
! CANADA – EMI NOTICE:
This Class A digital apparatus meets all requirements of the Canadian interference-causing equipment
regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du réglement sur le matérial
brouilleur du Canada.
4821-A2-GN21-10
July 2004
D
Notices to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was
performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It
does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment. The REN
assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may consist of any combination of devices subject
only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
When the equipment is used in a customer premises environment, a Model 6051 POTS Splitter must be used to ensure
CS-03 compliance. Refer to the POTS splitter installation instructions for details.
CE Marking
When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be
downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Library → Technical Manuals →
CE Declarations of Conformity.
Japan
Class A ITE
This is a Class A product based on the standard of the Voluntary Control Council for interference by Information
Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When
such trouble occurs, the user may be required to take corrective actions.
E
July 2004
4821-A2-GN21-10
Contents
About This Guide
1
2
3
„
Document Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . .
iii
„
Document Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iii
„
Related Product Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv
„
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
„
Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2
„
Cables Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3
„
Unpacking the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4
„
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4
„
Mounting Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6
„
Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6
„
Installing the Brackets for Rack Mounting . . . . . . . . . . . . . . . . . . . . . .
1-6
„
Installing the BitStorm 4800 Express Into a Rack . . . . . . . . . . . . . . . .
1-8
„
Installing the BitStorm 4800 Express on a Wall . . . . . . . . . . . . . . . . . .
1-10
„
Installing the BitStorm 4800 Express on a Shelf or Desktop . . . . . . . .
1-12
„
Cabling Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
„
DSL Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
„
10/100BaseT Uplink (Port 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3
„
Management Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4
„
Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5
Connecting a Terminal or PC to the Console Port. . . . . . . . . . . . .
2-5
Connecting a Modem to the Console Port. . . . . . . . . . . . . . . . . . .
2-6
„
Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7
„
Connecting to Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8
„
LED Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1
„
LED Meanings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2
Installation
Cabling
LEDs
4821-A2-GN21-10
July 2004
i
Contents
4
Configuration
„
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
„
Using the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2
Configure Management Default Gateway Address . . . . . . . . . . . .
4-2
Configure Management Inband Address . . . . . . . . . . . . . . . . . . . .
4-3
Configure Management Out-of-Band Address . . . . . . . . . . . . . . .
4-3
BitStorm 4800 Express Startup Procedure . . . . . . . . . . . . . . . . . . . . .
4-4
Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4
Management Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4
„
Startup Procedure for Inband Management . . . . . . . . . . . . . . . . . . . . .
4-5
„
Startup Procedure for Out-of-Band Management . . . . . . . . . . . . . . . .
4-5
„
Using the Web Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6
„
System / Users. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7
„
Configuration / Management / SNMP . . . . . . . . . . . . . . . . . . . . . . . . .
4-8
„
A Connectors and Pin Assignments
„
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-1
„
DSL Ports Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-2
„
Port 1 and Port 2 10/100BaseT Connectors . . . . . . . . . . . . . . . . . . . .
A-3
„
Console Port Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-4
B Equipment List
C Technical Specifications
Index
ii
July 2004
4821-A2-GN21-10
About This Guide
Document Purpose and Intended Audience
This document is written for technicians who install the BitStorm® 4800 Express
Model 4821-A2 IP DSLAM.
Document Summary
Section
Description
Chapter 1, Installation
Describes the physical installation of the BitStorm 4800
Express into a rack.
Chapter 2, Cabling
Describes how to install all cables for the BitStorm 4800
Express.
Chapter 3, LEDs
Explains the meaning and usage of the front panel LEDs.
Chapter 4, Configuration
Describes the minimal configuration steps required to
prepare the BitStorm 4800 Express for remote access,
using the command line interface and web interface.
Appendix A, Connectors
and Pin Assignments
Provides pinouts for connectors on the BitStorm 4800
Express.
Appendix B, Equipment List
Provides part numbers for the BitStorm 4800 Express and
related products.
Appendix C, Technical
Specifications
Lists the technical characteristics of the BitStorm 4800
Express.
Index
Lists key terms, acronyms, concepts, and sections in
alphabetical order.
A master glossary of terms and acronyms used in Paradyne documents is
available on the World Wide Web at www.paradyne.com. Select Support →
Technical Manuals → Technical Glossary.
4821-A2-GN21-10
July 2004
iii
About This Guide
Related Product Documents
Documentation for the BitStorm 4800 Express IP DSLAM is available on the World
Wide Web at www.paradyne.com. Select Support → Technical Manuals.
Document Number
Document Title
4821-A2-GB21
BitStorm 4800 Express Model 4821-A2 Command Line Interface
Reference
Describes the Command Line Interface (CLI) used to configure
and monitor the BitStorm 4800 Express.
4821-A2-GB22
BitStorm 4800 Express Model 4821-A2 SNMP Reference
Contains the information necessary to use Simple Network
Management Protocol (SNMP) to configure and monitor the
BitStorm 4800 Express.
6051-A2-GZ40
BitStorm 6051 POTS Splitter Installation Instructions
Describes how to install the BitStorm 6051 POTS splitter.
6210-A2-GB20
Hotwire 6210-A2, 6211-A2, and 6381-A2 User’s Guide
Describes the installation and operation of the 6210 ADSL
bridge, 6211 ADSL router, and 6381 ADSL/R router.
7890-A2-GB22
GrandVIEW EMS User’s Guide
Contains instructions for maintaining network services and
resources using the GrandVIEW Element Management System
(EMS).
To order a paper copy of a Paradyne document, or to talk to a sales representative,
please call 727-530-2000.
iv
July 2004
4821-A2-GN21-10
Installation
1
Overview
The BitStorm® 4800 Express is a stackable IP DSLAM designed for installation in
a Central Office (CO), multi-tenant unit (MTU), or multi-dwelling unit (MDU)
environment.
PORT1
10/100B
T
PORT2
10/100B
T
STATUS
ALARM
TEST
CONSOL
E
1
3
5
2
4
6
7
9 11
13 15
17 19
21 23
8 10
12 14
16 18
20 22
24
25 27
29 31
33 35
37 39
41 43
45 47
26 28
30 32
34 36
38 40
42 44
46 48
DSL POR
TS 1-24
POTS
DSL POR
TS 25-4
8
1-24
04-17534
The BitStorm 4800 Express is interoperable with the Hotwire 6381 ADSL/R
modem, as well as any standard ADSL CPE.
A Command Line Interface (CLI) and a web browser interface are provided. The
unit also may be managed using a network manager such as the Paradyne
GrandVIEW™ Element Management System (EMS).
BitStorm 4800 Express IP DSLAM models and features are listed in Table 1-1,
BitStorm 4800 Express Models and Features.
Table 1-1.
4821-A2-GN21-10
BitStorm 4800 Express Models and Features
Model Number
Type
Number of Ports
4821-A2-427
ADSL
24
4821-A2-447
ADSL
48
July 2004
1-1
1. Installation
Preparation
Consider the following before installing the BitStorm 4800 Express IP DSLAM:
„
Installation Site
Your installation site should be well ventilated, clean, and free of
environmental extremes.
„
Installation Options
The BitStorm 4800 Express may be:
— Mounted with the included mounting brackets in a standard 19-inch
(483 mm) or 23-inch (584 mm) rack (including both Bay Networks and
Nortel 23-inch racks), or, with separately purchased mounting brackets, in
a 21-inch (535 mm) ETSI rack. ETSI brackets are available from
Paradyne. See Appendix B, Equipment List.
As many BitStorm 4800 Express units may be mounted in a standard rack
as there are 1.75-inch (44.45 mm) spaces in the rack, so long as
adequate cooling is provided.
— Mounted vertically against a wall.
The standard mounting brackets provided can be fastened to the base of
the unit for wall mounting.
— Set on a shelf or desktop.
Up to five BitStorm 4800 Express units may be stacked on a shelf or
desktop.
„
Power
The BitStorm 4800 Express operates from a 90 to 265 VAC, 47 to 63 Hz power
source.
„
Cabling
No cable except the power cable is provided with the BitStorm 4800 Express.
See Table 1-2, Cable Descriptions, to determine what cables you need to
procure before installation.
1-2
July 2004
4821-A2-GN21-10
1. Installation
Cables Required
Table 1-2 shows all the cables that may be required for your installation.
Table 1-2.
Cable Descriptions
Connector Name
Connector and Cable
For Connecting . . .
DSL PORTS 1–24
50-pin RJ21X Telco-type
straight connector and 50-wire
cable. Two cables required for
48-port model.
Up to 24 DSL ports per cable to
a POTS splitter.
Port 2
10/100BaseT
8-position modular plug and
8-wire Category 5 or better
unshielded twisted pair (UTP)
cable.
The BitStorm 4800 Express to a
network.
Port 1
10/100BaseT
8-position modular plug and
8-wire Category 5 or better
unshielded twisted pair (UTP)
cable.
A Network Management System
(NMS) over a Local Area
Network (LAN) employing
10BaseT or 100BaseT.
CONSOLE
DB9 plug connector and
shielded cable.
The BitStorm 4800 Express to
one of the following:
„ The other connector
„ A terminal or a PC with a
DSL Ports 25–48
(if installed)
depends on the serial port on
your terminal or PC, but
normally is a DB9 socket.
„ The other connector
terminal emulation program,
or
„ A modem.
depends on the serial port on
your modem, but normally is
a DB25 plug. A null modem
(crossover) cable is required.
4821-A2-GN21-10
July 2004
1-3
1. Installation
Unpacking the Hardware
HANDLING PRECAUTIONS FOR
! STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from damage
due to electrostatic discharge (ESD) during normal operation. When
performing installation procedures, however, take proper static control
precautions to prevent damage to equipment. If you are not sure of the
proper static control precautions, contact your nearest sales or service
representative.
The BitStorm 4800 Express is shipped in a cardboard shipping container.
Carefully remove the unit from its shipping container and check for physical
damage. If the unit shows signs of shipping damage, notify your sales
representative.
Package Contents
In addition to this installation guide, the BitStorm 4800 Express shipping carton
should contain:
„
BitStorm 4800 Express DSLAM
„
AC Power Cable
„
Two sets of mounting brackets: one set suitable for a 19-inch (483 mm) rack
and one set suitable for a 23-inch (584 mm) rack (including Bay Networks and
Nortel)
„
Hardware kit (see Table 1-3, Contents of Hardware Kit Shipped with the
BitStorm 4800 Express)
If anything is missing, notify your sales representative.
Before installing the BitStorm 4800 Express, read the Important Safety
Instructions in the beginning of this document.
Be sure to register your warranty at www.paradyne.com/warranty.
1-4
July 2004
4821-A2-GN21-10
1. Installation
Table 1-3.
Contents of Hardware Kit Shipped with the BitStorm 4800 Express
Appearance
02-17259
Description
Quantity
Flat-head screw for attaching 19" mounting brackets to
unit
6
Machine screw with captive starwasher (6-32 x 1/4″) for
attaching 23" mounting brackets to unit
6
Self-retaining nut for racks without threaded holes
4
Dress screw (12-24 x 1/2″) for use with self-retaining
nuts
4
Machine screw with captive starwasher (10-32 x 1/2″)
for use with racks with threaded holes
4
Captive pan-head screw for replacing long Telco screw
2
Rubber foot for desk-mount and stacking of units
4
Cable tie (8″) for strain relief and cable management
2
02-17326
02-17256
02-17257
02-17258
02-17325
02-17261
02-17262
4821-A2-GN21-10
July 2004
1-5
1. Installation
Mounting Configurations
Three basic installation configurations are available:
„
Rack mount – see Installing the Brackets for Rack Mounting on page 1-6 and
Installing the BitStorm 4800 Express Into a Rack on page 1-8.
„
Wall mount – see Installing the BitStorm 4800 Express on a Wall on
page 1-10.
„
Shelf or desktop – see Installing the BitStorm 4800 Express on a Shelf or
Desktop on page 1-12.
Mounting Brackets
Your BitStorm 4800 Express can be installed in a rack or on the wall using
mounting brackets. Two brackets suitable for a 19-inch (483 mm) rack (marked
EIA-19) and two brackets suitable for a 23-inch (584 mm) Bay Networks or Nortel
rack (marked with Paradyne Part Number 868-6282-0020) are shipped with the
unit. Two brackets suitable for a 21-inch (535 mm) rack (marked ETSI) are
available from Paradyne as a separate feature (see Appendix B, Equipment List).
Rack-mounting brackets may also be used to attach the unit to a wall.
NOTE:
In this guide, the term rack refers to any rack, cabinet, frame, or bay suitable
for mounting telecommunications equipment.
Installing the Brackets for Rack Mounting
Procedure
To install the mounting brackets for rack mounting:
1. Locate the black screw nearest the front panel on each side of the unit, as
shown.
PORT1
10/100BT
PORT2
10/100BT
STATUS
ALARM
TEST
CONSOLE
1
3
5
2
4
6
7
9 11
13 15
17 19
21 23
8 10
12 14
16 18
20 22
24
25 27
29 31
33 35
37 39
41 43
45 47
26 28
30 32
34 36
38 40
42 44
46 48
DSL POR
TS 1-24
POTS
DSL POR
TS 25-48
1-24
04-17525
2. Remove these two black screws (one from each side) before attempting to
install the mounting brackets.
1-6
July 2004
4821-A2-GN21-10
1. Installation
3. Identify six flat-head screws (for 19-inch racks) or six machine screws (for
23-inch racks) provided with the mounting brackets in the hardware kit.
4. Attach the brackets appropriate to your rack size. Tighten all screws firmly.
19-inch (483 mm) Rack Mount
21.1-inch (535 mm) Rack Mount
4821-A2-GN21-10
July 2004
23-inch (584 mm) EIA and Bay Networks
Rack Mount
23-inch (584 mm) Nortel
Rack Mount
02-17324
1-7
1. Installation
Installing the BitStorm 4800 Express Into a Rack
Two types of mounting screws are provided. Use:
„
#10-32 mounting screws for rails with threaded screw holes
„
#12-24 mounting screws and self-retaining nuts for rails with unthreaded
screw holes
Procedure
To install the BitStorm 4800 Express into a rack:
1. Determine where in the rack you will mount the BitStorm 4800 Express. If your
rack does not have threaded screw holes, slip self-retaining nuts onto the rails
where the BitStorm 4800 Express will be fastened.
02-17070
2. Place the unit so that the brackets rest against the front of the rails. Insert
screws in the bottom screw positions and hand-tighten them.
1-8
July 2004
4821-A2-GN21-10
1. Installation
3. Insert and tighten the screws in the top screw positions, then tighten the
bottom screws.
PORT1
10/100B
T
PORT2
10/100B
T
STATUS
ALARM
TEST
CONSOL
E
1
3
5
7
2
4
6
8 10
12 14
16 18
20 22
24
9 11
13 15
17 19
21 23
25 27
29 31
33 35
37 39
41 43
45 47
26 28
30 32
34 36
38 40
42 44
46 48
DSL POR
TS 1-24
POTS 1-24
DSL POR
TS 25-4
8
LINK
PORT3
ACT
1000BT
GigE
STATUS
CONSOLE
ALARM
ALARM
PORT2-10/100BT
TEST
PORT1-10/100BT
POTS 1-24
1
3
5
2
7
4
9
6
11
8
13
10
15
12
17
14
19
16
21
18
23
20
22
24
DSL PORTS
1-24
04-17526
4821-A2-GN21-10
July 2004
1-9
1. Installation
Installing the BitStorm 4800 Express on a Wall
Wall mounting requires two wood screws suitable for the weight of the fully cabled
unit. These are not included. Use at a minimum 1/4-inch (6 mm) diameter screws
in 3/4-inch (19 mm) plywood (not drywall).
Procedure
To install the BitStorm 4800 Express on a wall:
1. Identify the flat-head screws provided in the hardware kit and the brackets
suitable for a 23-inch rack. Two screws are required for each bracket.
2. Orient the unit so that the bottom is facing you and the faceplate is at the top.
3. Locate the supplied Right Side mounting bracket and fasten it to the right side
of the unit.
04-17527
4. Locate the supplied Left Side mounting bracket and fasten it to the left side of
the unit.
5. Tighten all screws firmly.
1-10
July 2004
4821-A2-GN21-10
1. Installation
6. Install two wood screws (not provided) at the same height above the floor and
18.75 inches (476.25 mm) apart. Do not completely tighten the screws. Leave
them so their heads are about 1/4 inch (6 mm) from the wall.
17.85 in (453 mm)
04-17528
7. Hang the unit from the wood screws to verify that the screws are properly
placed. The screws should freely slide into the top of the key slots in the
brackets.
Do not fasten the unit to the wall until after it is completely cabled and tested.
4821-A2-GN21-10
July 2004
1-11
1. Installation
Installing the BitStorm 4800 Express on a Shelf or Desktop
If the BitStorm 4800 Express will be placed on a shelf or desktop, install the
provided rubber feet before putting the unit in position.
Procedure
To install the BitStorm 4800 Express on a shelf or desktop, as a standalone unit or
in a stack:
1. Locate the rubber feet in the hardware kit provided with the unit.
2. Turn the unit upside down on a work surface. Squares stamped into the
bottom of the unit show the proper positions for the feet.
3. Remove the protective sheet from the bottom of each foot, then press the foot
onto a corner of the bottom of the unit.
03-17439
4. Turn the unit right side up and place it in position on a shelf or desktop.
If the installation includes more than one unit, one can be stacked atop
another. Up to five units can be stacked together.
1-12
July 2004
4821-A2-GN21-10
Cabling
2
Cabling Overview
The BitStorm 4800 Express has a large variety of possible cabling configurations.
This chapter describes all possible connections, not all of which are required:
4821-A2-GN21-10
„
DSL Ports on page 2-2
„
10/100BaseT Uplink (Port 2) on page 2-3
„
Management Port on page 2-4
„
Console Port on page 2-5
„
Ground on page 2-7
„
Connecting to Power on page 2-8
July 2004
2-1
2. Cabling
DSL Ports
The BitStorm 4800 Express DSL connector supports the tip and ring connections
of up to 24 DSL ports over a 50-position cable. There are two DSL connectors on
the 48-port model.
You must connect the unit to a separate POTS splitter. The Model 6051 POTS
Splitter must be used for customer premises applications in Canada.
Procedure
To cable the DSL Ports:
1. Insert a cable tie (provided) through the top of the anchor mount next to the
DSL PORTS 1–24 connector.
2. If the connector for your cable has a short captive screw, attach the cable to
the DSL PORTS 1–24 connector and fasten it to the jack screw with its short
captive screw.
#4-40
Jack Screw
Anchor
Mount
Short
Screw
50-Pin
Connector
02-17083
3. If the connector for your cable has a long captive screw, remove the provided
jack screw from the threaded hole next to the DSL PORTS 1–24 connector.
Attach the DSL PORTS 1–24 connector to the unit using the long, captive
pan-head screw (provided).
Anchor
Mount
Long
Screw
50-Pin
Connector
02-17346
4. Tighten the cable tie around the connector and trim the excess.
02-17084
5. For a 48-port model, repeat Step 1 through Step 4, substituting
DSL Ports 25–48 for DSL PORTS 1–24.
2-2
July 2004
4821-A2-GN21-10
2. Cabling
6. Secure the cables as required for strain relief.
10/100BaseT Uplink (Port 2)
Port 2 is the uplink for the DSLAM. A straight-through cable can be used
regardless of the destination interface, since the port automatically distinguishes
between an MDI and an MDIX.
Procedure
To use Port 2 as the uplink:
1. Connect an 8-position modular cable to Port 2.
2. Connect the other end of the cable to the uplink interface, such as an Ethernet
switch.
4821-A2-GN21-10
July 2004
2-3
2. Cabling
Management Port
Port 1 can be used to connect the BitStorm 4800 Express to a network
management system using a 10BaseT or 100BaseT LAN. A straight-through cable
can be used regardless of the destination interface, since the port automatically
distinguishes between an MDI and an MDIX.
Procedure
To use Port 1 as the out-of-band management port:
1. Connect an 8-position modular cable to Port 1.
2. If the BitStorm 4800 Express is in a rack, fasten the cable to a rail with a cable
tie.
3. Connect the other end of the cable to your Ethernet switch or a network
interface card in a PC.
Ethernet Switch
CONS
PORT1
10/100
BT
PORT2
10/100
BT
STATUS
ALARM
TEST
OLE
1
3
5
2
4
6
7 9
11 13
15 17
19 21
23
8 10
12 14
16 18
20 22
24
25 27
29 31
33 35
37 39
41 43
45 47
26 28
30 32
34 36
38 40
42 44
46 48
DSL PO
RTS 1-2
04-17529
Port 1
2-4
4
July 2004
4821-A2-GN21-10
2. Cabling
Console Port
The CONSOLE port normally serves as the primary user interface with the
BitStorm 4800 Express during installation. You can connect a terminal or PC
directly to the CONSOLE port using a DTE cable (see procedure below). You can
also use the CONSOLE port to attach a modem to the BitStorm 4800 Express for
remote dial-in management of the unit using a DCE cable (see Connecting a
Modem to the Console Port on page 2-6).
Connecting a Terminal or PC to the Console Port
Procedure
To connect a terminal or PC to the CONSOLE port:
1. Configure the terminal or terminal emulation program to use the following
parameters:
— Speed: 9600 bps
— Data bits: 8
— Parity: None
— Flow Control: None
— Stop bits: 1
2. Determine and procure the proper Data Terminal Equipment (DTE) cable type.
The CONSOLE port requires a DB9 plug connector. The other connector
depends on the serial port on your terminal or PC.
3. Connect the DB9 plug connector to the CONSOLE port socket. The
CONSOLE port is ordinarily used only during installation, so do not fasten the
connector.
4. Connect the other end of the cable to the serial port of your terminal or PC.
Serial
Port
E
PORT1
10/100B
T
PORT2
10/100B
T
STATUS
ALARM
TEST
CONSOL
1
3
5
2
4
6
7 9
11 13
15 17
19 21
23
8 10
12 14
16 18
20 22
24
25 27
29 31
33 35
37 39
41 43
45 47
26 28
30 32
34 36
38 40
42 44
46 48
DSL POR
TS 1-24
04-17530
4821-A2-GN21-10
July 2004
2-5
2. Cabling
Connecting a Modem to the Console Port
Procedure
To connect a modem to the CONSOLE port:
1. Determine and procure the proper DCE cable type for your modem. The
CONSOLE port requires a DB9 plug connector. The other connector depends
on the serial port on your modem, but normally a DB25 plug is required. The
cable must be an EIA-232-E crossover (null modem) cable.
2. Connect the DB9 plug connector to the CONSOLE port socket.
3. If the modem will be permanently connected, fasten the connector to the
Management Module with its captive screws. If the BitStorm 4800 Express is
in a rack, dress the cable to the left and attach it to the rail with a cable tie.
4. Connect the other end of the cable to the serial port of your modem.
Serial Port
Modem
PWR
OLE
PORT1
10/100
BT
TST
LINE
ETHER
NET
PORT2
10/100
BT
STATUS
ALARM
TEST
CONS
ALM
1
3
5
2
4
6
7 9
11 13
15 17
19 21
23
8 10
12 14
16 18
20 22
24
25 27
29 31
33 35
37 39
41 43
45 47
26 28
30 32
34 36
38 40
42 44
46 48
DSL PO
CONSOLE
Port
2-6
RTS 1-2
4
04-17531
July 2004
4821-A2-GN21-10
2. Cabling
Ground
Procedure
To connect the unit to a ground:
1. Crimp a ring terminal onto the stripped end of 14 AWG or heavier copper
ground wire.
2. Remove the screw marked by the ground symbol (
front panel.
) at the right side of the
3. Fasten the ring terminal to the front panel using the same screw.
4. Attach the ground wire to an earth ground.
POTS 1-2
4
DSL PO
RTS 25
-48
To Earth Ground
04-17532
4821-A2-GN21-10
July 2004
2-7
2. Cabling
Connecting to Power
The BitStorm 4800 Express can be powered by any AC power source supplying
90–265 VAC at 47–63 Hz.
Procedure
To connect the BitStorm 4800 Express to a power source:
1. Insert the supplied power cord into the power socket on the back of the unit.
02-17248
2. If the BitStorm 4800 Express is in a rack, dress the power cord to the left and
fasten it to the rail with a cable tie.
3. Connect the other end of the power cord to a grounded AC power source.
4. Make sure the STATUS LED on the front panel is ON (green). See Chapter 3,
LEDs.
2-8
July 2004
4821-A2-GN21-10
LEDs
3
LED Locations
The locations of the System and DSL Port LEDs on the front panel of the
BitStorm 4800 Express are shown in Figure 3-1, Front Panel LEDs.
Link LEDs
PORT1
10/100BT
DSL Ports LEDs
PORT2
10/100BT
STATUS
ALARM
TEST
CONSOLE
Activity LEDS
1
3
5
7
9 11 13 15 17 19 21 23
25 27 29 31 33 35 37 39 41 43 45 47
2
4
6
8 10 12 14 16 18 20 22 24
26 28 30 32 34 36 38 40 42 44 46 48
04-17533
PORT1
10/100B
T
PORT2
10/100B
T
STATUS
ALARM
TEST
CONSO
LE
1
3
5
7
2
4
6
8 10
12 14
16 18
20 22
24
9 11
13 15
17 19
21 23
25 27
29 31
33 35
37 39
41 43
45 47
26 28
30 32
34 36
38 40
42 44
46 48
DSL PORTS
1-24
POTS
DSL PORTS
Figure 3-1.
4821-A2-GN21-10
1-24
25-48
Front Panel LEDs
July 2004
3-1
3. LEDs
LED Meanings
When power is first applied to the unit, it performs a power-on self-test. When this
test is successfully completed, the Status LED blinks. The meaning of all the LEDs
is shown in Table 3-1, Front Panel LEDs.
Table 3-1.
Front Panel LEDs
LED
Color
State
Meaning
Link*
Green
Off
No Ethernet link present.
On
Ethernet Link present.
Flashing
Ethernet link is present, but port is
administratively disabled.
Off
No data is being transferred.
On
Data is being transferred.
Off
No power, or the unit has not completed
initialization.
On
Unit has power and has completed initialization.
Off
No Alarms.
On
Unit failed self-test, or the unit has exceeded a
safe temperature, or a fan has failed.
Off
Normal operating mode.
On
At least one port is in test mode.
Off
The port is disabled or no signal is detected on
the line.
On
Port has successfully trained with the remote
and is active.
Activity*
STATUS
ALARM
TEST
DSL Ports
(LEDs
numbered 1–24
or 1–48
correspond to
DSL ports 1–24
or 1–48)
Green
Green
Amber
Amber
Green
* The RJ45-type connectors for Port 1 and Port 2 bear two LEDs: the left one is the
Link LED and the right one is the Activity LED.
3-2
July 2004
4821-A2-GN21-10
Configuration
4
Overview
The BitStorm 4800 Express is designed to require minimal configuration before it
can be accessed by a Network Operations Center (NOC). When the
BitStorm 4800 Express is first powered up it is a fully functional bridge, and all
DSL ports are set to their maximum speed.
Initial configuration is performed using the Command Line Interface (CLI). The CLI
is available from a terminal or PC connected to the CONSOLE port, or through the
management port (Port 1).
Additional configuration may be necessary, depending on the mode used to
manage the BitStorm 4800 Express:
„
Inband
„
Out of band through Port 1
This can be performed using the CLI, SNMP, or the web interface.
For more configuration information, see the BitStorm 4800 Express Model
4821-A2 Command Line Interface Reference (for the CLI) and the online Help (for
the web interface).
4821-A2-GN21-10
July 2004
4-1
4. Configuration
Using the CLI
A command line interface (CLI) can be used to configure and monitor the unit. The
CLI is available from a PC or terminal connected to the Console port, or from a
Telnet session with the device.
The following commands are available:
Table 4-1.
CLI Commands
Command
Function
clear
Clear the system log.
configure
Enter Configuration mode.
copy
Copy from one file to another.
date
Set the time zone and date format.
end
If user is in Administrator mode, shifts to User mode; if user is in
User mode, positions interface at top of menu tree.
exit
Terminate current session.
firmware
Download or apply new firmware.
paging
Enable or disable paging (more prompt) for this session.
privilege
Enable administrator mode.
restart
Restart a unit.
show
Display configuration, statistics, and status.
technical-support
Display information for contacting technical support.
test
Test the system.
Descriptions of some essential configuration commands follow.
Configure Management Default Gateway Address
The configure management default gateway command specifies the IP address
of the next hop router for the management traffic.
configure management default-gateway {ip_address}
Minimum Access Level: Administrator
ip_address – Specifies the IP address of the default gateway for the management ports.
Example:
PDYN# configure management default-gateway 137.90.127.1
4-2
July 2004
4821-A2-GN21-10
4. Configuration
Configure Management Inband Address
The configure management inband address command specifies the IP address
of the unit.
configure management inband address {ip_address} { subnet_mask}
Minimum Access Level: Administrator
ip_address – Specifies the management IP address. Default is 0.0.0.0 (disabled). Do
not configure inband and out-of-band management on the same subnet.
subnet_mask – Specifies the subnet mask to be applied to the IP address. The default
mask is 255.255.255.0.
Example:
PDYN# configure management inband address 137.90.127.3
255.255.255.0
Configure Management Out-of-Band Address
The configure management out-of-band address command specifies the IP
address of the unit that will accept management traffic on the out-of-band
management port.
configure management out-of-band address {bootp | {{ip_address} {
subnet_mask} }
Minimum Access Level: Administrator
bootp – Specifies that a BOOTP server will determine the management IP address.
ip_address – Specifies the management IP address. The default address is
10.10.10.10. Do not configure inband and out-of-band management on the same
subnet.
subnet_mask – Specifies the subnet mask to be applied to the IP address. The default
mask is 255.255.255.0.
Example:
4821-A2-GN21-10
PDYN# configure
management out-of-band address bootp
PDYN# configure
255.255.255.0
management out-of-band address 137.90.127.3
July 2004
4-3
4. Configuration
BitStorm 4800 Express Startup Procedure
You can initialize your BitStorm 4800 Express via a PC or terminal connected to
the unit’s CONSOLE port. Then, using a series of CLI commands, GrandVIEW
EMS or another Element Management System, or the web interface, you can
configure the unit according to your requirements.
Login
Procedure
To log in to the BitStorm 4800 Express:
1. Connect a PC or terminal to the CONSOLE port. (See Console Port in
Chapter 2, Cabling.)
2. At the login> prompt, type admin and press Enter.
3. At the password> prompt, press Enter. The default login password is blank.
4. At the PDYN> prompt, type privilege and press Enter.
5. At the password# prompt, press Enter. The default privileged password is
blank.
You are now logged on and in privileged mode, which allows you to configure the
unit.
Management Modes
The startup procedure for the BitStorm 4800 Express system differs depending on
the type of management used:
4-4
„
Inband Management – Operates over the uplink.
„
Out-of-Band Management – Operates over Port 1.
July 2004
4821-A2-GN21-10
4. Configuration
Startup Procedure for Inband Management
With inband management, the BitStorm 4800 Express is managed using the
uplink port.
Procedure
To start up the BitStorm 4800 Express using inband management:
1. To avoid losing your connection when the IP address is changed, access the
CLI using the CONSOLE port.
2. Assign an IP address, netmask, and next-hop router using the configure
management command. For example:
PDYN# configure management inband address 137.90.127.3
255.255.255.0
PDYN# configure management default-gateway
137.90.127.1
Do not configure inband and out-of-band management on the same subnet.
Startup Procedure for Out-of-Band Management
In out-of-band management, you manage the unit through Port 1.
Procedure
To start up the BitStorm 4800 Express using out-of-band management:
1. To avoid losing your connection when the IP address is changed, access the
CLI using the CONSOLE port.
2. Assign an IP address, netmask, and next-hop router using the configure
management command. For example:
PDYN# configure management out-of-band address
137.90.80.3 255.255.255.0
PDYN# configure management default-gateway 137.90.80.1
You can now access the web interface by typing into the Location field of your
web browser the IP address assigned to the Port 1. See Using the Web
Interface on page 4-6.
Do not configure inband and out-of-band management on the same subnet.
3. Configure routers as necessary to route data from the NOC to the
BitStorm 4800 Express.
4821-A2-GN21-10
July 2004
4-5
4. Configuration
Using the Web Interface
To access the web interface:
Procedure
1. Open your web browser. (Internet Explorer Version 6 or above is
recommended.)
2. Type http:// and the IP address of the BitStorm 4800 Express into the Address
field of your browser window. For example:
3. A login window appears. Enter the default User ID (admin) and leave
Password blank. Click on OK. The web interface screen appears.
4. Click on the menu tab appropriate to what you would like to do:
— Configuration – To configure the system and interfaces
— Status – To display statistics, status, and contents of memory
— System – To display system information, download firmware, back up
configurations, and modify users
— Diagnostics – To start and stop tests
4-6
July 2004
4821-A2-GN21-10
4. Configuration
System / Users
For security reasons, it is a good idea to change the default password the first time
you use the system.
Procedure
To change the default password for user admin:
1. Click on the System menu tab, then click on Users. The folllowing screen
appears.
2. In the Configured Users box, select admin by clicking in the circle next to it.
3. Click on Modify Selected. The System / Users / admin screen appears.
4. Type in a new Login Password and a new Privilege Password, then click on
Apply. Keep a record of the new password.
4821-A2-GN21-10
July 2004
4-7
4. Configuration
Configuration / Management / SNMP
SNMP access to the unit is disabled by default. The read-only community string is
public, and the read-write string is private. Community strings, network
management system addresses, and trap manager addresses can be set using
the System/Management/SNMP screen.
Procedure
To set SNMP parameters:
1. Click on the Configuration menu tab, then click on SNMP. The
System/Management/SNMP screen appears.
2. Enter new SNMP parameters as desired. Click on Apply.
4-8
July 2004
4821-A2-GN21-10
Connectors and Pin Assignments
A
Overview
The following sections provide pin assignments for:
PORT1
10/100BT
DSL Ports Connectors on page A-2
„
Port 1 and Port 2 10/100BaseT Connectors on page A-3
„
Console Port Connector on page A-4
PORT2
10/100BT
STATUS
ALARM
TEST
CONSOLE
„
1
3
5
7
9 11 13 15 17 19 21 23
25 27 29 31 33 35 37 39 41 43 45 47
2
4
6
8 10 12 14 16 18 20 22 24
26 28 30 32 34 36 38 40 42 44 46 48
DSL PORTS 1-24
DSL PORTS 25-48
04-17535
Figure A-1.
4821-A2-GN21-10
BitStorm 4800 Express IP Front Panel
July 2004
A-1
A. Connectors and Pin Assignments
DSL Ports Connectors
The 50-pin RJ21X Telco connectors labeled DSL Ports 1–24 and (on the 48-port
model) DSL Ports 25–48 provide the 2-wire loop interface from each DSL port to
the POTS splitter. The Canadian designation for this connector is CA21A.
Table A-1 lists the pin assignments for these interfaces. Note that Pins 25 and 50
are not used.
Table A-1. DSL Connector Pinouts
A-2
DSL Port
Connector Pins
(Ring, Tip)
1 or 25
1, 26
2 or 26
2, 27
3 or 27
3, 28
4 or 28
4, 29
5 or 29
5, 30
6 or 30
6, 31
7 or 31
7, 32
8 or 32
8, 33
9 or 33
9, 34
10 or 34
10, 35
11 or 35
11, 36
12 or 36
12, 37
13 or 37
13, 38
14 or 38
14, 39
15 or 39
15, 40
16 or 40
16, 41
17 or 41
17, 42
18 or 42
18, 43
19 or 43
19, 44
20 or 44
20, 45
21 or 45
21, 46
22 or 46
22, 47
23 or 47
23, 48
24 or 48
24, 49
July 2004
1
25
50
26
02-17151
4821-A2-GN21-10
A. Connectors and Pin Assignments
Port 1 and Port 2 10/100BaseT Connectors
Port 1 and Port 2 are 8-pin unkeyed modular jacks for a 10/100BaseT interface.
Table A-2. Port 1 and Port 2 Pinouts
4821-A2-GN21-10
Signal
Pin
Transmitted Data +
1
Transmitted Data –
2
Received Data +
3
Unused
4
Unused
5
Received Data –
6
Unused
7
Unused
8
July 2004
Pin 1
Pin 8
97-15449
A-3
A. Connectors and Pin Assignments
Console Port Connector
The CONSOLE port connector is a DB9 socket connector that supports an
EIA-232-E circuit as shown in Table A-3.
Table A-3. Console Port Connector
A-4
RS-232 Signal
Direction
Pin
Ground
Out
1
Receive Data
Out
2
Send Data
In
3
Data Terminal Ready
In
4
Ground
—
5
Ground
Out
6
NC
—
7
Ground
Out
8
NC
—
9
July 2004
4821-A2-GN21-10
Equipment List
B
Table B-1.
BitStorm 4800 Express Equipment List
Description
Model Number
BitStorm 4800 Express Model 4821-A2 Command Line Interface
Reference (paper copy)
4821-A2-GB21
BitStorm 4800 Express Model 4821-A2 SNMP Reference (paper
copy)
4821-A2-GB22
BitStorm 4800 Express 24-Port IP DSLAM, with North America
power cord
4821-A2-427
Includes BitStorm 4800 Express, 19- and 23-inch mounting brackets
and hardware, and Installation Guide.
BitStorm 4800 Express 48-Port IP DSLAM, with North America
power cord
4821-A2-447
Includes BitStorm 4800 Express, 19- and 23-inch mounting brackets
and hardware, and Installation Guide.
4821-A2-GN21-10
Mounting Brackets for ETSI 21-inch (535 mm) Rack
4200-F1-001
1-Slot POTS Splitter Chassis
5011-A1-000
6-Slot POTS Splitter Chassis
5016-A1-000
BitStorm 6051 Universal Line Sharing POTS Splitter
6051-B1-001
July 2004
B-1
B. Equipment List
B-2
July 2004
4821-A2-GN21-10
Technical Specifications
C
Technical specifications are subject to change without notice.
Table C-1. BitStorm 4800 Express Technical Specifications
Specifications
Criteria
Cooling and Air
Handling
Each BitStorm 4800 Express is independently cooled with integral fans
and does not rely on vertical air flow.
DSL
Compatibility
„ G.dmt (G.992.1)
„ G.lite (G.992.2)
„ ANSI T1.413-1998
Electromagnetic
Compatibility
(EMC)
Meets the following standards:
„ EN 300 386-2
„ EN 55024
„ EN 55022, Class A
„ FCC Part 15, Class A
„ VCCI, Class A
Interfaces
„ DSL PORTS: 50-pin RJ21X Telco-type connector
„ CONSOLE: DB9 (EIA-232-E)
„ Port 1 and Port 2: 8-pin modular jack (10/100BaseT)
Operating
Environment
Ambient Temperature: 0° to 50° C (32° to 122° F)
Relative Humidity: 5% to 95% noncondensing
Storage Temperature: –40° to 85° C (–40° to 185° F)
Shock and vibration tolerance sufficient to withstand normal shipping
Physical
Dimensions
Height: 1.75″ (44.5 mm, or 1U as defined in EIA-310-C) without feet
Width: 17.2″ (437 mm) without mounting brackets
Depth: 16.0″ (406 mm) with cables
Power
90–265 VAC, 47–63 Hz
Power
Consumption
Model 4821-A2-427: 26 Watts Maximum
Weight
Model 4821-A2-427: 11.2 lbs (5.1 kg)
Model 4821-A2-447: 40 Watts Maximum
Model 4821-A2-447: 10.7 lbs (4.8 kg)
4821-A2-GN21-10
July 2004
C-1
C. Technical Specifications
C-2
July 2004
4821-A2-GN21-10
Index
Numerics
10/100BaseT pinouts, A-3
A
AC power, 2-8
Activity LEDs, 3-2
administrator, login, 4-4
Alarm LED, 3-2
audience for this document, iii
autosensing, 2-3–2-4
B
BitStorm 4800 Express
description, 1-1
features, 1-1
models, 1-1
brackets
installation for rack mount, 1-6
C
cables, A-1
DSL ports, A-2
MGMT port, A-3
required, 1-3
cabling, 2-1
console port, 2-5
DSL ports, 2-2
ground, 2-7
management port, 2-4
Port 1, 2-4
Port 2, 2-3
POTS ports, 2-2
power, 2-8
uplink, 2-3
CO grounding screw, 2-7
Command Line Interface (CLI), 4-2
commands, 4-2
community strings, 4-8
configuration, 4-1
CLI commands, 4-2
mounting brackets, 1-6
configuring
inband management, 4-5
out-of-band management, 4-5
SNMP parameters, 4-8
4821-A2-GN21-10
connectors, A-1
DSL ports, A-2
front panel, A-1
Management port, A-3–A-4
POTS splitter, A-2
CONSOLE port, 2-5
cabling and settings, 2-5
connecting modem, 2-6
description, 1-3
pinouts, A-4
contents of shipping carton, 1-4
cooling and air handling, C-1
D
DB9
cabling, 2-5
pinouts, A-4
default gateway, 4-2
default password, 4-4
changing, 4-7
desktop installation, 1-12
dimensions, C-1
document purpose, iii
documents
online, iii
ordering, iv
related, iv
DSL ports
cabling, 2-2
description, 1-3
LEDs, 3-2
pin assignments, A-2
E
earth ground, 2-7
EIA-232-E, A-4
Electromagnetic Compatibility (EMC), C-1
EMS, 4-4
Enter key, 4-2
environment, C-1
equipment list
hardware provided, 1-5
package contents, 1-4
part numbers, B-1
ESD precautions, 1-4
July 2004
IN-1
Index
Ethernet
LEDs, 3-2
F
fasteners provided, 1-5
feature numbers, B-1
features, 1-1
feet, 1-12
front panel, 3-1, A-1
illustration, A-1
LEDs, 3-1
G
glossary URL, iii
grounding screw, 2-7
H
hardware kit contents, 1-5
I
inband management
configuring, 4-5
described, 4-4
initialization procedures, 4-4
installation, 1-1
options, 1-2
installing
feet for shelf installation, 1-12
in rack, 1-8
mounting brackets for rack mount, 1-6
mounting brackets for wall mount, 1-10
on shelf or desktop, 1-12
screws for wall mount, 1-11
self-retaining nuts, 1-8
unit into rack, 1-8
unit on wall, 1-10
interfaces, C-1
J
jack screw, 2-2
L
LEDs, 3-1
License Agreement, B
Link LEDs, 3-2
login, 4-4
lug for grounding, 2-7
M
Management port
cabling, 2-4
connector, A-3–A-4
description, 1-3
pin assignments, A-3–A-4
management port, 2-4
menu tabs, 4-6
models, 1-1
modem
connecting to Console port, 2-6
mounting brackets, description, 1-6
mounting configurations, 1-2, 1-6
N
network management systems, 4-8
NMS, 4-8
O
operating environment, C-1
optional mounting brackets, 1-6
order numbers, B-1
out-of-band management
configuring, 4-5
described, 4-4
overview
cabling, 2-1
configuration, 4-1
management modes, 4-4
of BitStorm 4800 Express, 1-1
of book, iii
P
package contents, 1-4
part numbers, B-1
password, 4-4
changing, 4-7
default, 4-4
PC cabling and settings, 2-5
physical dimensions, C-1
pin assignments, A-1
Console port, A-4
Management port, A-3–A-4
Ports 1 and 2, A-3
RJ21X connectors, A-2
Telco connectors, A-2
Port 1
cabling, 2-4
pinouts, A-3
Port 2
cabling, 2-3
pinouts, A-3
management modes, 4-4
IN-2
July 2004
4821-A2-GN21-10
Index
POTS splitter
cabling, 2-2
pin assignments, A-2
port description, 1-3
power, C-1
connecting to, 2-8
consumption, C-1
requirements, 2-8, C-1
preinstallation, 1-2
product-related documents, iv
purpose of this document, iii
R
rack installation, 1-8
bracket installation, 1-6
example, 1-9
procedure, 1-8
related documents, iv
Return key, 4-2
RJ21X connectors, A-2
RJ45 pinouts, A-4
S
screws provided, 1-5
shelf installation, 1-12
shipping carton, 1-4
site preparation, 1-2
site requirements, 1-2, C-1
SNMP, configuring parameters, 4-8
Software and Firmware License Agreement, B
specifications
product, C-1
stacking, 1-2
startup procedures, 4-4
4821-A2-GN21-10
Status LED, 3-2
synopsis of chapters, iii
T
technical specifications, C-1
Telco connectors
fastening, 2-2
pinouts, A-2
terminal cabling and settings, 2-5
Test LED, 3-2
trap managers, 4-8
troubleshooting, LEDs, 3-1
turn-up procedures, 4-4
typographic conventions, 4-2
U
unpacking, 1-4
uplink
cabling, 2-3
Port 2, 2-3
V
VT100 cabling and settings, 2-5
W
wall mount
bracket installation, 1-10
screw positions, 1-11
web interface
password, 4-7
starting, 4-6
using, 4-6
weight, C-1
July 2004
IN-3
Index
IN-4
July 2004
4821-A2-GN21-10
Download PDF