30" (76.2 cm) Freestanding Gas Range PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS KFGD500E

30" (76.2 cm) Freestanding Gas Range PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS KFGD500E
30" (76.2 cm) Freestanding Gas Range
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
B*
KFGD500E
GAS SUPPLY REQUIREMENTS
Type of Gas:
Natural Gas:
• This range is factory set for use with Natural gas. See “Gas
Conversions” section. The model/serial/rating plate is located
on the oven frame behind the top left side of the oven door
has information on the types of gas that can be used. If the types
of gas listed do not include the type of gas available, check
with the local gas supplier.
C**
A**
D
LP gas conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial/rating plate for use with a different gas
without consulting the serving gas supplier. See “Gas Conversions”
section.
Gas Supply Line
• Provide a gas supply line if 3/4" (1.9 cm) rigid pipe to the range
location. A smaller pipe on longer runs may result in insuffient
gas supply. With LP gas, piping or tubing size can be 1/2"
(1.3 cm) minimum. Usually, LP gas suppliers deteremine the size
and materials used in the system. NOTE: Pipe-joint compounds that
resist the action of LP gas must be used. Do not use TEFLON tape.
Flexible metal appliance connector:
• If local codes permit, a new CSA design-certified, 4 to 5 ft
(122 to 152.4 cm) long, 1/2" (1.3 cm) or 3/4" (1.9 cm) I.D.
(inside diameter), flexible metal appliance connector
may be used for connecting range to the gas supply line.
E***
F
A. 353/4" ± 1/8" (90.8 ± 0.3 cm) cooktop height (minimum)
with leveling legs screwed all the way in**
B. Model/serial/rating plates (located behind the control panel)*
C. 473/8" ± 1/8" (120.3 ± 0.3 cm) overall height (minimum)
with leveling legs screwed all the way in**
D. 281/2" ± 1/4" (72.4 ± 0.6 cm) depth with handle
E. 261/8" ± 1/8" (69.2 ± 0.3 cm)***
F. 2915/16" ± 1/16" (76.0 ± 0.2 cm) width
* Model/serial/rating plates may be rotated up from behind the control
panel for viewing front the front of the range.
** Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
***Excludes handle. Dimension given is from wall to front of oven door
and will vary based on electronic outlet receptacle installation.
ELECTRICAL REQUIREMENTS
• A /2" (1.3 cm) male pipe thread is needed for connection
to the female pipe threads of the inlet to the appliance
pressure regulator.
To properly install your range, you must determine the type of electrical
connection you will be using and follow the instructions provided
for it here.
• Do not kink or damage the flexible metal tubing when moving
the range.
• Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial/rating plate. The
model/serial/rating plate is located behind the control panel. Refer
to the figure in "Product Dimensions" in the "Location
Requirements" section.
1
• Must include a shutoff valve:
The supply line must be equipped with a manual shutoff valve.
This valve should be located in the same room but external
to the range opening, such as an adjacent cabinet. It should
be in a location that allows ease of opening and closing. Do not block
access to shutoff valve. The valve is for turning on or shutting off gas
to the range.
• This range is manufactured with a 4-wire power supply cord rated
at 240 volts, 40 amps, rated at 194°F (90°C) and investigated for use
with this range.
Range Rating*
Specified Rating of Power
Supply Cord Kit and Curcuit
Protection
B
A. Gas supply line
B. Shutoff valve “open” position
C. To range
A
C
120/240 Volts
120/208 Volts
Amps
Temp Rating
8.8 – 16.5 KW
7.8 – 12.5 KW
40 or 50
194°F (90°C)
16.6 – 22.5 KW
12.6 – 18.5 KW
50
194°F (90°C)
* The NEC calculated load is less than the total connected load listed
on the model/serial/rating plate.
TEFLON is a registered trademark of E.I. Du Point De Nemours and Company.
†®
Page 1 of 2
Because Whirlpool Corporation includes a continues commitment to improve our products,
Dimensions are for planning purposes only. For complete details,
we reserve the right to change materials and specifications without notice.
see Installation Instructions packed with product. Specifications subject
to change without notice.
Ref. W10694069B
08/10/15
CABINET OPENING DIMENSIONS
Cabinet opening dimensions shown are for 25" (64.0 cm) countertop
depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop
height.
IMPORTANT: If installing a range hood or microwave hood combination
above the range, follow range hood or microwave hood combination
installation instructions for dimensional clearances above
the cooktop surface.
Range may be installed with zero clearance to combustible
construction at the rear and on the sides below the cooktop.
D
B
C
A
E
A. 18" (45.7 cm) upper cabinet to countertop
B. 13" (33.0 cm) upper cabinet depth
F
C. 30" (76.2 cm) min. opening width
J
K
D. For minimum clearance to the top of the cooktop, see NOTE.
E. In U.S.A.: 30" (76.2 cm) min. opening width
In Canada: 31" (78.7 cm) min. opening width
G
I
L
H
F. 3
" (7.6 cm) min. clearance from both sides of the range
to the side of the wall or other combustible material.
G. Cabinet door or hinges should not extend into the cutout.
H. 3" (7.6 cm) distance from wall
I. 11/2" (3.8 cm) min. from the right side cabinet
J. 8" (20.3 cm) width
K. 7" (17.8 cm) min. from floor
L. 2" (5.1 cm) min. from floor
L
8½"
(21.6 cm)
* Drill on centerline 11/4" (3.1 cm) from rear wall for gas supply line.
14"
*** (35.6 cm)
** G
as lines must be installed within the shaded area to ensure proper
alignment of this oven with cabinets.
*** R
ecessed electrical plugs must be installed within the shaded
area to ensure proper alignment of this oven with cabinets.
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet
is covered by not less than 1/4 " (0.64 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet steel, 0.015" (.04 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
1½"
(3.8 cm)
2¼" (5.7 cm)
1¼"*
(3.1 cm)
8½" (21.6 cm)**
gas line location
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bttom of an uncovered wood or metal cabinet.
Page 2 of 2
Because Whirlpool Corporation includes a continues commitment to improve our products,
Dimensions are for planning purposes only. For complete details,
we reserve the right to change materials and specifications without notice.
see Installation Instructions packed with product. Specifications subject
to change without notice.
Ref. W10694069B
08/10/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising