GTD42EASJ Ge Series 7.2 Cu. Ft. Capacity electric Dryer

Add to my manuals
3 Pages

advertisement

GTD42EASJ Ge Series 7.2 Cu. Ft. Capacity electric Dryer | Manualzz
GTD42EASJ
Ge® Series 7.2 Cu. Ft. Capacity Electric Dryer
Dimensions and Installation Information
(in inches)
22 1/2"
5600W
24A
60Hz
208V
4400W
22A
60Hz
27"
Power Cord 4 1/2"
27"
Electric Dryer Rating:
240V
29 1/2"
11 3/4"
Exhaust Option: 4-way rear, right, left and bottom
Circuit Requirements: An individual, properly-grounded branch circuit,
protected by a 30-amp circuit breaker or a time-delay fuse, is required.
Note: Dryer wall outlet must be located within 36" of service cord entry and
acessible when dryer is mounted in position.
Installation Information: For complete information, see installation
instructions packed with your dryer.
Special Installation Requirements
Alcove or Closet Installation:
- If your dryer is approved for installation in an alcove or closet, it will be stated
on a label on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces
are: 0" either side; 3" front and rear
5.7
- Minimum vertical space from floor to overhead cabinets, ceilings, etc. is
52".cu. ft. Dryers
- Closet doors must be louvered or otherwise ventilated and must contain a minimum
of 60 sq. in. of open area equally distributed. If this closet contains both a2washer
and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
- The dryer MUST be exhausted to the outdoors.
Power
- The installation must conform with the local codes, or in the absence of local codes,
Cord
Hole
with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas
dryers.
30-1/2
Minimum Clearances other than Alcove or Closet Installation:
- Minimum clearances to combustible surfaces are: 0" both sides; 3" rear
Dryer Exhausting Information­: Use metal duct only, vertical and horizontal ducting.
Back View
For answers to your Monogram®, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
44"
37 1/2"
8"
1 3/4"
3 1/2"
5"
3 1/4"
Side View
View
Side
Rear View
Rear
View
5.8,
6.0 and
7.0 cu.
ft. Dryers
Power
Cord
Locations
5
Power
Cord Hole
4-1/2
Back View
View
Back
Listed by
Underwriters
Laboratories
Specification Created 3/15
GE Dryer Vent
GTD42EASJ
Ge® Series 7.2 Cu. Ft. Capacity Electric Dryer
Dryer exhausting information—
use metal duct only vertical and
horizontal ducting
For complete information, see installation instructions
packed with your dryer.
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all rigid metal
exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal
(semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it
may be necessary to connect the dryer to the house vent using a flexible metal
(foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in
installations where rigid metal or flexible metal (semi-rigid) ducting cannot be
used AND where a 4” diameter can be maintained throughout the entire length
of the transition duct. Please see installation instruction packed with your dryer
for complete instructions when using flexible metal (foil type) ducting.
Exhaust Length Calculation:
1.Determine the number of 90° turns needed for your installation. If you
exhaust to the side or bottom of dryer, add one turn.
2.The maximum length of 4" rigid (aluminum or galvanized) duct which can be
tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45°
turns within the duct length should be treated as a 90° elbow. A turn over 45°
should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under
any enclosed house floor (crawl space), or into an attic, since the accumulated
lint could create a fire hazard or moisture could cause damage. Never terminate
the exhaust into a common duct or plenum with a kitchen exhaust, since the
combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back
drafts, bird nesting, etc. The wall cap must also be located at least 12" above
the ground or any other obstruction with the opening pointed down.
For more information on venting kits and accessories,
please call 1-800-GE-CARES.
For answers to your Monogram®, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
A
A
4
B
Best performance
Maximum length
of 4" dia rigid
4
2-1/2
metal duct
B
Exhaust hood type
Number
A
B
2-1/2
of 90°
4"
2-1/2"
Domestic dryer models
turns
opening opening
0
200 ft.
175 ft.
1
185 ft.
165 ft.
2
175 ft.
155 ft.
3
165 ft.
145 ft.
GE Frontload Long Vent
4
155 ft.
135 ft.
7.0 cu. ft. capacity
electric dryer (GFDL)
5
145 ft.
125 ft.
0
150 ft.
125 ft.
1
135 ft.
115 ft.
2
125 ft.
105 ft.
Long Vent 6.0 - 8.0
3
115 ft.
95 ft.
cu. ft. capacity electric
4
105 ft.
85 ft.
& gas dryers
5
95 ft.
75 ft.
(GTDL and GTV)
0
120 ft.
90 ft.
1
100 ft.
75 ft.
2
85 ft.
65 ft.
Long Vent 6.1-7.4 cu. ft.
3
70 ft.
55 ft.
capacity electric & gas
4
60 ft.
45 ft.
(GTD42, GTD45, GTD65,
GTX42 and GTX65)
5
55 ft.
35 ft.
All 6.0 - 8.3 cu. ft.
0
90 ft.
60 ft.
capacity models electric
1
60 ft.
45 ft.
and gas dryers (GFDS,
2
45 ft.
35 ft.
GFDR, GFDN, GTDS,
3
35 ft.
25 ft.
GTDN, GHDN, GHDS,
4
25 ft.
15 ft.
GTDP,GLDP, GTD, HTDP,
HTDX)
0
90 ft.
60 ft.
1
60 ft.
45 ft.
2
45 ft.
35 ft.
DCVH480
3
35 ft.
25 ft.
0
46 ft.
37 ft.
1
37 ft.
30 ft.
2
30 ft.
22 ft.
All 3.6 cu. ft. (DSKS,
DSKP) electric dryers
3
23 ft.
15 ft.
0
56 ft.
42 ft.
1
48 ft.
34 ft.
2
40 ft.
26 ft.
Laundry Center GUD27
3
32 ft.
18 ft.
0
43 ft.
36 ft.
1
33 ft.
26 ft.
Laundry Center GUD24
2
24 ft.
16 ft.
A
Specification Created 3/15
GTD42EASJ
Ge® Series 7.2 Cu. Ft. Capacity Electric Dryer
Features and Benefits
Auto Dry – For clothes that come out feeling and looking great, this setting
monitors air temperature to set the optimal drying time
WrinkleCare Extended Tumble – Reduces wrinkling and creasing
End-Of-Cycle Signal – Alerts you when the load is done, so clothes can be
removed before wrinkles set in
4 heat selections – Provide the right temperatures for your clothes-drying needs
Up to 120 ft venting capability – Provides flexible installation
Model GTD42EASJWW – White
Specification Created 3/15

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement