GTD42GASJ GE Series 7.2 Cu. Ft. Capacity Gas Dryer

GTD42GASJ GE Series 7.2 Cu. Ft. Capacity Gas Dryer
GTD42GASJ
GE® Series 7.2 Cu. Ft. Capacity Gas Dryer
Dimensions and Installation Information (in inches)
Special Installation Requirements
Exhaust Option: When viewed from the front of the
unit, exhaust 3-way via rear, left and bottom. Dryer is shipped
exhausted to the rear. Alternate exhausting knockouts
are supplied.
Alcove or Closet Installation:
- If your dryer is approved for installation in an alcove or closet, it will be stated
on a label on the dryer back.
Gas: An individual, properly-grounded branch circuit, with
a three-prong grounding-type receptacle, protected by a 15
or 20 amp circuit breaker or a time-delay fuse is required.
- Minimum
clearances between dryer cabinet and adjacent walls or other
surfaces are: 0" either side; 3" front and rear
Gas Dryer Electric Rating: 120V, 60Hz, 6A
Gas (BTU/HR): 22,000. Factory-equipped for natural gas.
Tested for LP gas. LP gas supply requires a conversion kit.
Check installation instructions for correct kit and have a
qualified gas technician install a conversion kit. See dryer
ducting information for proper installation.
Note: Dryer wall outlet must be located within 36" of service
cord entry and accessible when dryer is mounted in position.
Installation Information: For complete information,
see installation instructions packed with your dryer.
-T
he dryer MUST be exhausted to the outside.
- Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
- Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet
with a gas dryer.
Bathroom or Bedroom Installation:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence
of local codes, with the National Electric Code and National Fuel Gas
Code, ANSI Z223 for gas dryers.
Minimum Clearances other than Alcove or Closet
Installation:
- Minimum clearances to combustible surfaces are: 0" both sides; 3" rear
Dryer Exhausting Information­: Use metal duct only, vertical
and horizontal ducting.
For answers to your Monogram®, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Specification Created 3/15
GTD42GASJ
GE® Series 7.2 Cu. Ft. Capacity Gas Dryer
5.7 cu. ft. Dryers
Dimensions and Installation Information (in inches)
5.8,
6.0 and
7.0 cu.
ft. Dryers
Power
Cord
Locations
5
2
22 1/2"
29 1/2"
27"
Power Cord 4 1/2"
27"
11 3/4"
30-1/2
Power
Cord Hole
Power
Cord Hole
4-1/2
Back View
BAck
View
Back
View
44"
37 1/2"
8"
3 1/2"
1 3/4"
5"
3 1/4"
Side View
Rear View
Side View
Rear View
For answers to your Monogram®, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Specification Created 3/15
GTD42GASJ
GE® Series 7.2 Cu. Ft. Capacity Gas Dryer
Dryer exhausting information—
use metal duct only vertical and
horizontal ducting
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct.
If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used
(Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house
vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used
ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND
where a 4" diameter can be maintained throughout the entire length of the transition duct. Please see
installation instruction packed with your dryer for complete instructions when using flexible metal
(foil type) ducting.
Exhaust Length Calculation:
1.Determine the number of 90° turns needed for your installation. If you exhaust to the side or
bottom of dryer, add one turn.
2.The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown
in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house
floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture
could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen
exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc.
The wall cap must also be located at least 12" above the ground or any other obstruction with the
opening pointed down.
For more information on venting kits and accessories, please call
1-800-GE-CARES.
For every extra 90° elbow, reduce the allowable vent system length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
The total vent system length includes all the straight portions and elbows of the system (transition duct included).
Best performance
A
For complete information, see installation instructions packed
with your dryer.
A 4
B
A
4
2-1/2
B
Domestic dryer models
2-1/2
GE Frontload Long Vent 7.0
cu. ft. capacity electric dryer
(GFDL)
Long Vent 6.0 - 8.0 cu. ft.
capacity electric & gas dryers
(GTDL and GTV)
Long Vent 6.1-7.4 cu. ft.
capacity electric & gas
(GTD42, GTD45, GTD65,
GTX42 and GTX65)
All 6.0 - 8.3 cu. ft. capacity
models electric and gas dryers
(GFDS, GFDR, GFDN, GTDS,
GTDN, GHDN, GHDS, GTDP,
GLDP, GTD, HTDP, HTDX)
DCVH480
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
Laundry Center GUD27
For answers to your Monogram®, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Laundry Center GUD24
Maximum length
of 4" dia rigid
metal duct
Exhaust hood type
Number
A
B
of 90°
4"
2-1/2"
turns
opening opening
0
200 ft.
175 ft.
1
185 ft.
2
175 ft.
165 ft.
155 ft.
3
165 ft.
145 ft.
4
155 ft.
135 ft.
5
145 ft.
125 ft.
0
1
2
3
4
5
0
1
2
3
4
5
0
150 ft.
135 ft.
125 ft.
115 ft.
105 ft.
95 ft.
120 ft.
100 ft.
85 ft.
70 ft.
60 ft.
55 ft.
90 ft.
125 ft.
115 ft.
105 ft.
95 ft.
85 ft.
75 ft.
90 ft.
75 ft.
65 ft.
55 ft.
45 ft.
35 ft.
60 ft.
1
2
3
4
0
1
2
3
0
60 ft.
45 ft.
35 ft.
25 ft.
90 ft.
60 ft.
45 ft.
35 ft.
46 ft.
45 ft.
35 ft.
25 ft.
15 ft.
60 ft.
45 ft.
35 ft.
25 ft.
37 ft.
1
2
3
0
37 ft.
30 ft.
23 ft.
56 ft.
30 ft.
22 ft.
15 ft.
42 ft.
1
2
3
0
1
2
48 ft.
40 ft.
32 ft.
43 ft.
33 ft.
24 ft.
34 ft.
26 ft.
18 ft.
36 ft.
26 ft.
16 ft.
Specification Created 3/15
GTD42GASJ
GE® Series 7.2 Cu. Ft. Capacity Gas Dryer
Features and Benefits
Auto Dry – For clothes that come out feeling and looking great, this setting monitors
air temperature to set the optimal drying time
Wrinkle Care extended tumble – reduces wrinkling and creasing
End-Of-Cycle Signal – Alerts you when the load is done, so clothes can be removed
before wrinkles set in
4 heat selections – Provide the right temperatures for your clothes-drying needs
Up to 120 ft venting capability – Provides flexible installation
Model GTD42GASJWW – White
GTDP220EFWW
Specification Created 3/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement