Osram LM10A-A1 (33-641-06)

Osram LM10A-A1 (33-641-06)
Data Sheet
LINEARlight Flex
OS-LM10A
Benefits
Picture for
Datasheet
is missing
!!!
¾
Linear separable LED strip on flexible
printed circuit board with self-adhesive
back
¾
Small in size
¾
Available in various colors
Applications
¾
Edge-lighting of transparent or diffused
materials
¾
Path & contour marking
¾
Illuminated signs
Technical Operating Data
Product
Color
Number of
LEDs
Voltage
[V DC]*
Power
[W]*
Current
[A]*
Radiance
Angle [°]*
Wavelength [nm]
Color Temp [K]*
Lum. Flux
[lm]*
OS-LM10A-W2-865
white
600
24
86,4
3,6
120
6500 K
1290
OS-LM10A-W1-865
white
600
24
57,6
2,4
120
6500 K
540
OS-LM10A-W2-854
white
600
24
86,4
3,6
120
5400 K
1290
OS-LM10A-W1-854
white
600
24
57,6
2,4
120
5400 K
540
OS-LM10A-W2-847
white
600
24
86,4
3,6
120
4700 K
1290
OS-LM10A-W1-847
white
600
24
57,6
2,4
120
4700 K
540
OS-LM10A-A1
red
600
24
72,0
3
120
617 nm
1620
OS-LM10A-Y1
yellow
600
24
72,0
3
120
587 nm
1290
OS-LM10A-T1
green
600
24
72,0
3
120
525 nm
675
OS-LM10A-B1
blue
600
24
72,0
3
120
470 nm
170
*)
All Data are related to the entire module
Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Technical Features
¾ Modules optimized for use with OSRAM
OPTOTRONIC power supplies.
¾ Entire Module consists of 600 LEDs
¾ Wide viewing angle enables homogeneously
¾ Dimmable by pulse width modulation (PWM)
with the electronic controller OT DIM
illuminated surfaces
¾ Size of printed circuit board (LxWxH): 8400 mm
¾ Smallest unit of 10 LEDs can be cut out at
regular intervals without damaging the rest of
the module
OS-LM10A - 01.03.2005
x 10 mm x 3 mm
¾ Size of smallest unit 10 LED
(LxW): 140 mm x 10 mm
Page 1 of 4
Minimum and Maximum Ratings
Product
Operating Temperature
at Tc-Point [ °C ] *
Storage Temperature
[ °C ] *
Voltage Range
[ V dc ] *
Reverse Voltage
[ V dc ] *
OS-LM10A-W2-865
-30 ... 75
-40 ... 85
23 ... 25
25
OS-LM10A-W1-865
-30 ... 75
-40 ... 85
23 ... 25
25
OS-LM10A-W2-854
-30 ... 75
-40 ... 85
23 ... 25
25
OS-LM10A-W1-854
-30 ... 75
-40 ... 85
23 ... 25
25
OS-LM10A-W2-847
-30 ... 75
-40 ... 85
23 ... 25
25
OS-LM10A-W1-847
-30 ... 75
-40 ... 85
23 ... 25
25
OS-LM10A-A1
-30 ... 85
-40 ... 85
23 ... 25
25
OS-LM10A-Y1
-30 ... 85
-40 ... 85
23 ... 25
25
OS-LM10A-T1
-30 ... 75
-40 ... 85
23 ... 25
25
OS-LM10A-B1
-30 ... 75
-40 ... 85
23 ... 25
25
*)
Exceeding maximum ratings for operation and storage temperature will reduce expected life time or destroy the LED Module.
Exceeding maximum ratings for operation voltage will cause hazardous overload and will likely destroy the LED Module.
The temperature of the LED module needs to measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature
sensitive label (available e.g. at RS-Components). For exact location of the Tc-point see drawing below.
Drawing
Drawing is missing !!!
OS-LM10A - 01.03.2005
Page 2 of 4
Safety Information
¾ The LED module itself and all its components may not be mechanical stressed.
¾ Assembly must not damage or destroy conducting paths on the circuit board.
The LED Module incorporates no protection against short circuits, overload or overheating. Therefore it is absolutely necessary to
operate the modules with a electronically stabilised power supply offering protection against the above mentioned safety risks.
For dimming applications attention should be paid to specific references in "OPTOTRONIC Technical Guide".
OSRAM OPTOTRONIC power supplies are specifically designed with protection features for safe operation.
When using power supplies other than OPTOTRONIC the following basic safety features are required, in addition to any other
application specific concerns and local safety codes:
¾ Short circuit protection
¾ Overload protection
¾ Overheat protection
¾ Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards.
Only qualified personnel should be allowed to perform installations.
¾ Correct electrical polarity needs to be observed. Wrong polarity may destroy the module!
¾ Parallel connection is highly recommended as safe electrical operation mode.
Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and demage the LED module.
¾ Please ensure that the power supply is of adequate power to operate the total load.
¾ When mounting on metallic or otherwise conductive surfaces, there needs to be a electrical isolation at soldering points between
module and the mounting surface.
¾ The maximum length of LINEARlight Flex OS-LM10A is 4200 mm with power feed at one end (OS-LM10A-W2 3500 mm). The
complete module 8400 mm ( OS-LM10A-W2 7000 mm) can be operated with a two pole power feed in the middle of the module or
from both ends, when do you use one power supply.
¾ Pay attention to standard ESD precautions when installing the module.
¾ The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. The ability
to customize the length of the module by cutting at specifically marked points is a key feature of the product and hence the reason
for no factory installed conformal coating. For these reasons, it is recommended that the user complete all module modifications
first ( cutting, wiring) and then apply a conformal coating in the final stages of installation.
¾ Damage by corrosion will not be honored as a materials defect claim. It is the user´s responsibility to provide suitable protection
against corrosive agents such as moisture and condensation and other harmful elements.
¾ For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable
protection class. The module can be protected against condensation water by treatment with an appropriate circuit board grade
conformal coating. The conformal coating should have the following features:
- Optical transparency
- UV-resistance
- thermal expansion matching the thermal expansion of the module 15-30*10^-6 cm/cm/K
- low permeability of steam for all climatic conditions
- resistance against corrosive environment
The lacquer APL of the company Electrolube http://www.electrolube.com met the conditions for the LINEARlight Flex in our tests.
OS-LM10A - 01.03.2005
Page 3 of 4
Assembly Information
¾ Solder connections should only be performed on designated solder pads ( marked "24V +/-"). During soldering, do not exceed the
maximum soldering time of 10 seconds and the maximum soldering temperature of 260°C.
¾ The smallest unit (140 mm- 10 LEDs) can be removed by cutting with scissors between the designated solder pads.
¾ The mounting of the module is facilitated by means of the double-sided adhesive on the back-surface of the module. Care must be
taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particle. The mounting substrate
must have sufficient structural integrity. Take care to completely remove the adhesive backing. Once the module is appropriately
positioned, press on the module with about 20N/cm² ( refer to application techniques of 3M adhesive transfer tapes).
¾ The minimum bending radius is 2 cm. The module may be bent over a smaller radius but only in regions of the circuit board
containing no electronic components and such bends should be made once and fixed in position to avoid cyclic fatigue.
¾ The thermal length expansion coefficent of the modul is 17*10^-6cm/cm/K. When installing in enviroments with large variations in
temperature ( e.g. outdoor applications) and operating length of more than 2 m, the use of metallic mounting surfaces is
necessary. Otherwise it is advisable to use an additional thicker adhesive tape to absorb the stress of any mismatch in expansion
coefficients.
Ordering Guide
S-Unit *
Productgroup
Productname
EAN *
LINEARlight Flex
OS-LM10A-W2-865
4050300887265
8
LINEARlight Flex
OS-LM10A-W1-865
4050300873817
8
LINEARlight Flex
OS-LM10A-W2-854
4050300887289
8
LINEARlight Flex
OS-LM10A-W1-854
4050300817170
8
LINEARlight Flex
OS-LM10A-W2-847
4008321040145
8
LINEARlight Flex
OS-LM10A-W1-847
4050300817156
8
LINEARlight Flex
OS-LM10A-A1
4008321040060
8
LINEARlight Flex
OS-LM10A-Y1
4050300946030
8
LINEARlight Flex
OS-LM10A-T1
4050300946054
8
LINEARlight Flex
OS-LM10A-B1
4050300945491
8
*) EAN: Ordering number per single module
S-Unit: Modules per shipping unit
Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves.
Sales and Technical Support
OSRAM GmbH
Hellabrunner Strasse 1
D - 81536 München
Germany
www.osram.com
+49 (0)89 6213-0
Sales and technical support is given by the
local OSRAM subsidiaries.
On our world wide homepage all OSRAM
subsidiaries are listed with complete
address and phone numbers.
Related and Further Information
¾ The new dimension of light
53 S006 GB
¾ New creativity in lighting design
LED Modules for illuminated signs
153 S07 E
¾ OPTOTRONIC Technical Guide
130 T08 E
¾ OPTOTRONIC Data Sheets
www.osram.com
OS-LM10A - 01.03.2005
Page 4 of 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement