Wolf IDF364C Design Guide

PDF Download

Document

INTERNATIONAL DESIGN GUIDE

C O N T E N T S

Wolf Built-In Ovens

Wolf Electric Cooktops

Wolf Gas Cooktops

Wolf Integrated Modules

Wolf Warming Drawers

Wolf Dual Fuel Ranges

Wolf Sealed Burner Rangetops 40

Wolf Gas Ranges 46

Wolf Gas Rangetops

Wolf Cooktop Ventilation

Wolf Ventilation

Recommendations

Features and specifications indicated herein and on our website are subject to change at any time without notice.

Check our website, wolfappliance.com

for the most up-to-date specifications.

WOLF ® is a registered trademark of Wolf Appliance, Inc.

I M P O R T A N T N O T E

As you follow these instructions, you will notice warning and caution symbols.

This blocked information is important for the safe and efficient installation of

Wolf equipment. There are two types of potential hazards that may occur during installation.

signals a situation where minor injury or product damage may occur if you do not follow instructions.

states a hazard that may cause serious injury or death if precautions are not followed.

Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problem-free installation.

W E L C O M E T O W O L F A P P L I A N C E

In this Design Guide, you’ll find all the necessary information for specifying a Wolf oven, cooktop, range, rangetop or ventilation equipment into the next kitchen or home you design.

Each unit is handcrafted with the knowledge and experience gleaned from being the premier supplier of cooking equipment to professional chefs and their restaurants for nearly 75 years.

Sub-Zero, a corporate companion and kitchen soul mate, shares the identical values and pride we take in providing the best cooking equipment.

A Wolf is beautiful and will complement any design you use, whether it be contemporary or traditional.

But that’s not why many customers turn to us.

We have a passion for cooking and it shows in our work. Consumers appreciate the unique features we have built in to our many different models. You can refer to specifics as you page through this guide.

The features are as numerous as the various units you have to choose from. But one of the more prominent highlights is the Wolf Dual

Convection System that is in all our built-in ovens and dual fuel ranges. It delivers even temperature and airflow throughout the oven.

Its combination of fans and heating elements operate either simultaneously or in sequence, depending on which of the ten different cooking modes your client chooses.

In addition, our dual-stacked burners on the gas cooktops, dual fuel ranges and sealed burner rangetops are all sealed and offer you the capability of simmering foods.

Our electric cooktops are unique to the industry with their capabilities of providing simmer on all elements and the melt feature on one of the elements. The triple element on the 914 mm cooktop can generate up to 2,700 watts for those large pots that need fast boiling.

If you are looking for cooking performance, but don’t want to shout it out in your kitchen design, one of our unframed electric cooktops may be your choice. There’s no stainless steel trim, just the sophisticated black ceramic glass top that can be mounted flush with the top of the countertop or as a frameless installation sitting on top of the countertop surface.

The sizes, alternative tops, and selection of the standard classic stainless steel and the premium finishes of carbon or platinum stainless steel make your decision-making process much more fun for you and your clients. Now you can give them exactly what they want without sacrificing the quality they demand.

In all your applications you can depend on Wolf.

That reputation is even stronger because it is backed by Sub-Zero. The combination of the two is really greater than their sum.

Review this Design Guide in greater detail when you get a chance and keep it as a handy reference. We are confident you will like what you see.

Model ISO30U/S

Model ISO36U/S

Model IDO30U/S

B U I L T - I N O V E N S

W O L F L S E R I E S B U I L T - I N O V E N S

It’s hard to put into a few words the differences you will see in the Wolf L Series ovens compared to others on the market. Some of those differences are very dramatic. Did you notice that the control panel closes? It’s an attractive feature and will enable you to hide that control panel that many of us have labored to make functional and tried to make beautiful.

Inside, the beauty, design and functionality continue. Brilliant halogen lights illuminate the beautiful blue interior. As you open the oven door, feel the smoothness of the door damper system. Pull that bottom oven rack all the way out and notice how it is nestled on the door rails. With the dual convection fans, all models offer ten different cooking modes.

F E A T U R E S

Dual convection logic control system

Ten cooking modes—bake, roast, broil, convection bake, convection roast, convection broil, convection, bake stone (accessory required), proof and dehydrate (accessory required)

Rotating glass touch control panel

Cobalt blue porcelain oven interior

Three removable racks, six-level rack guide and full-extension bottom rack—five-level rack guide for 914 mm oven

Large viewing triple-pane window

Dual interior halogen lighting

Hidden bake element and recessed broil element

Temperature probe and receptacle

Self-clean, delayed start and Sabbath features

Door hinge with hydraulic damper assures smooth opening and closing of the door

Factory-installed trim

This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org.

L S E R I E S O V E N F E A T U R E S

Model ISO30U/S shown

Electronics and door cooling vents

Recessed broil element

Thermostat

Three removable racks

Hidden bake element

Door hinge with hydraulic damper

Exhaust vent

Triple-pane window

Rotating electronic control panel

Oven door light switch

Location of rating plate

Probe receptacle

Halogen lights

Gasket

Removable six-level rack guide

B U I L T - I N O V E N S

P L A N N I N G I N F O R M A T I O N

There are only three different sizes to consider when planning for your layout. You can choose either a 762 mm or 914 mm built-in single oven or a 762 mm double oven.

For ease of installation, Wolf recommends using

838 mm wide cabinets with 762 mm ovens and

991 mm wide cabinets with the 914 mm oven.

You will need a minimum 610 mm of usable cabinet depth. The cabinet must be able to support 113 kg for a single oven and 181 kg for a double oven.

Wolf built-in ovens have a face trim on all four sides and will overlap stiles and rails. The trim overlaps 3 mm on the bottom, 5 mm on the top and 19 mm on each side.

Specifications on the following pages provide overall dimensions, rough openings and installation specifics for the three different oven sizes.

We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation.

A Wolf single oven may be installed below an electric or gas cooktop. Wolf built-in ovens are designed and agency approved for installation with Wolf cooktops only. Refer to the electric and gas cooktops sections for additional specifications. A built-in oven cannot be installed below a Wolf rangetop.

E L E C T R I C A L R E Q U I R E M E N T S

International (I) models come with a factory installed transformer and require a 220-240

V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. The appropriate electrical connection must be provided in accordance with local requirements.

IMPORTANT NOTE: Unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in an adjacent cabinet within reach of the conduit. A

51 mm diameter hole to route the conduit through cabinetry will be required. Refer to the

Installation Specifications illustrations on the following pages for location of the electrical supply.

You must follow all local codes and ordinances when installing your service.

M O D E L O P T I O N S

Built-In Ovens

762 mm Single Oven – Unframed

Classic Stainless ISO30U/S

914 mm Single Oven – Unframed

Classic Stainless ISO36U/S

762 mm Double Oven – Unframed

Classic Stainless IDO30U/S

This appliance must be installed in accordance with local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit that is protected by a properly sized circuit breaker or time delay fuse.

The proper voltage, frequency and amperage ratings are listed on the product rating plate.

A C C E S S O R I E S

Built-In Ovens

Bake stone accessory, includes stone, rack and peel

Additional oven racks

Two-piece broiler pan and temperature probe

Dehydration racks with door stop

Accessories are available through your Wolf dealer.

B U I L T - I N O V E N S

M O D E L O P T I O N S

762 mm Built-In Single Oven

Unframed / Classic ISO30U/S

S P E C I F I C A T I O N S

762 mm Built-In Single Oven

Overall Dimensions 759 mm x 699 mm

(W x H x D) x 610 mm

Door Clearance 527 mm

Overall Oven

Interior Capacity 127 L

Overall Interior Dim 635 mm x 419 mm

(W x H x D) x 483 mm

Usable Interior Dim 546 mm x 419 mm

(W x H x D) x 416 mm

Cabinet Width

Cabinet Depth

Min Base Support

Opening Width

Opening Height

838 mm rec

762 mm min

610 mm min

113 kg

724 mm

691 mm

Trim Overlaps

Electrical Supply

5 mm top

3 mm bottom

19 mm each side

220-240 V AC, 50/60 Hz

30 amp dedicated circuit

Conduit

Electrical Rating

Total Amps

Shipping Weight

1.2 m flexible 4-wire

5.1 kW at 240 V

124 kg

I N S T A L L A T I O N O P T I O N S

The Wolf 762 mm single oven may be installed below a Wolf 762 mm electric or gas cooktop. Unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven within reach of the conduit. The Wolf 762 mm single oven may also be installed below a Wolf 914 mm electric or gas cooktop.

The Wolf 762 mm single oven may be installed in combination with a Wolf warming drawer.

A Wolf 762 mm single oven may be installed next to another 762 mm single oven. You must allow for a 64 mm space between the oven rough openings. Also, a separate inner wall is required for each oven between openings.

Refer to installation instructions shipped with each Wolf product for detailed specifications.

O V E R A L L D I M E N S I O N S

762 mm Built-In Single Oven

759 mm

699 mm

76 mm

RIGHT SIDE VIEW

CONDUIT

CHANNEL

662 mm

INSIDE

SIDE TRIM

48 mm

610 mm

BEHIND FRAME

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

762 mm Built-In Single Oven

Wall Application

610 mm min

OPENING DEPTH

691 mm

OPENING

HEIGHT

Undercounter Installation

95 mm min

610 mm min

OPENING DEPTH

691 mm

OPENING

HEIGHT

914 mm

STANDARD

FLOOR TO

COUNTER

HEIGHT

121 mm min

TOP VIEW

48 mm

716 mm

32 mm

610 mm

OPEN OVEN DOOR

527 mm

711 mm

838 mm

RECOMMENDED CABINET WIDTH

762 mm min

724 mm

OPENING WIDTH

ELECTRICAL LOCATION

WITHIN OPENING

APPLIES ONLY TO

CABINETS DEEPER

THAN 610 mm

127 mm

102 mm

838 mm

RECOMMENDED CABINET WIDTH

762 mm min

ELECTRICAL

LOCATION WITHIN

OPENING APPLIES

127 mm

ONLY TO CABINETS

DEEPER THAN 610 mm

102 mm

724 mm

OPENING WIDTH

IMPORTANT NOTE: Unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in an adjacent cabinet within reach of the conduit. Choose the location shown in the illustrations that best suits your installation.

B U I L T - I N O V E N S

O V E R A L L D I M E N S I O N S

914 mm Built-In Single Oven

905 mm

619 mm

76 mm

Unit dimensions may vary to ± 3 mm.

914 mm Built-In Single Oven

Wall Application

610 mm min

OPENING DEPTH

611 mm

OPENING

HEIGHT

Undercounter Installation

95 mm min

610 mm min

OPENING DEPTH

197 mm rec

121 mm min

611 mm

OPENING

HEIGHT

914 mm

STANDARD

FLOOR TO

COUNTER

HEIGHT

RIGHT SIDE VIEW

CONDUIT

CHANNEL

584 mm

INSIDE

SIDE TRIM

48 mm

610 mm

BEHIND FRAME

I N S T A L L A T I O N S P E C I F I C A T I O N S

991 mm

RECOMMENDED CABINET WIDTH

914 mm min

ELECTRICAL LOCATION

WITHIN OPENING APPLIES

ONLY TO CABINETS

DEEPER THAN 610 mm

127 mm

102 mm

876 mm

OPENING WIDTH

TOP VIEW

48 mm

867 mm

OPEN OVEN DOOR

870 mm

991 mm

RECOMMENDED CABINET WIDTH

914 mm min

876 mm

OPENING WIDTH

ELECTRICAL LOCATION

WITHIN OPENING APPLIES

ONLY TO CABINETS

DEEPER THAN 610 mm

127 mm

102 mm

E E

32 mm

M O D E L O P T I O N S

914 mm Built-In Single Oven

Unframed / Classic ISO36U/S

610 mm

451 mm

S P E C I F I C A T I O N S

914 mm Built-In Single Oven

Overall Dimensions 905 mm x 619 mm

(W x H x D) x 610 mm

Door Clearance 451 mm

Overall Oven

Interior Capacity 125 L

Overall Interior Dim 762 mm x 337 mm

(W x H x D) x 483 mm

Usable Interior Dim 673 mm x 337 mm

(W x H x D) x 416 mm

Cabinet Width

Cabinet Depth

Min Base Support

Opening Width

Opening Height

991 mm rec

914 mm min

610 mm min

113 kg

876 mm

611 mm

Trim Overlaps

Electrical Supply

5 mm top

3 mm bottom

19 mm each side

220-240 V AC, 50/60 Hz

30 amp dedicated circuit

Conduit

Electrical Rating

Total Amps

Shipping Weight

.9 m flexible 4-wire

5.1 kW at 240 V

131 kg

I N S T A L L A T I O N O P T I O N S

The Wolf 914 mm single oven may be installed below a Wolf 914 mm electric or gas cooktop.

Unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven within reach of the conduit.

The 914 mm single oven may also be installed below a Wolf 762 mm framed electric cooktop, but not below a 762 mm unframed electric cooktop or 762 mm gas cooktop. When installed below a cooktop, it is recommended that the opening for the oven be 197 mm from the floor to ease the use of the oven door.

The Wolf 914 mm single oven may be installed above or below a Wolf warming drawer with integrated drawer front.

A Wolf 914 mm single oven may be installed directly above another 914 mm oven. You must allow enough space between the oven rough openings to accommodate a base support for the top oven. A 914 mm single oven may be installed next to another 914 mm oven. You must allow for a 64 mm space between the oven rough openings. Also, a separate inner wall is required for each oven between openings. Each base cabinet support must be able to support 113 kg.

B U I L T - I N O V E N S

M O D E L O P T I O N S

762 mm Built-In Double Oven

Unframed / Classic IDO30U/S

S P E C I F I C A T I O N S

762 mm Built-In Double Oven

Overall Width

Overall Height

759 mm

1270 mm

Overall Depth

Door Clearance

610 mm

527 mm

Overall Oven Interior

Capacity (per oven) 127 L

Overall Interior Dim 635 mm x 419 mm

(W x H x D) x 483 mm each

Usable Interior Dim 546 mm x 419 mm

(W x H x D) x 416 mm each

Cabinet Width

Cabinet Depth

Min Base Support

Opening Width

Opening Height

838 mm rec

762 mm min

610 mm min

181 kg

724 mm

1260 mm

Trim Overlaps

Electrical Supply

5 mm top

3 mm bottom

19 mm each side

220-240 V AC, 50/60 Hz

50 amp dedicated circuit

Conduit

Electrical Rating

Total Amps

Shipping Weight

1.5 m flexible 4-wire

8.9 kW at 240 V

211 kg

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

O V E R A L L D I M E N S I O N S

762 mm Built-In Double Oven

1270 mm

RIGHT SIDE VIEW

CONDUIT

CHANNEL

48 mm

1232 mm

INSIDE

SIDE TRIM

759 mm 76 mm

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

762 mm Built-In Double Oven

Wall Application

610 mm min

OPENING DEPTH 1260 mm

OPENING

HEIGHT

1702 mm typical

610 mm

BEHIND FRAME

32 mm

610 mm

OPEN OVEN DOOR

527 mm

724 mm

OPENING WIDTH

TOP VIEW

48 mm

716 mm

711 mm

838 mm

RECOMMENDED CABINET WIDTH

762 mm min

ELECTRICAL LOCATION

WITHIN OPENING

APPLIES ONLY TO

CABINETS DEEPER

THAN 610 mm

127 mm

102 mm

W O L F E L E C T R I C C O O K T O P S

W O L F F R A M E D E L E C T R I C C O O K T O P S

Behind the sophisticated, minimalist exterior, beneath that perfectly smooth, subtly patterned glass that cleverly reduces scratches, there is a high-performance cooking tool.

The black ceramic glass top is beautifully complemented by the classic stainless steel trim.

Multiple cooking elements with different zones allow your customer a variety of different applications. The 914 mm cooktop features a 305 mm diameter triple heating element—concentric rings that give you exceptional control of temperature for pans and pots of every size.

All of the heating elements offer True Simmer, and with each cooktop there is one element that enables you to set a temperature for melting.

F E A T U R E S

Classic stainless steel trim finish

Easy-to-clean black ceramic glass surface is resistant to scratching, staining, impact and heat—translucent surface allows you to see the glow of hot elements

Illuminated electronic touch controls with graduated control lighting

Ribbon-type radiant heating elements—some elements with multiple temperature zones

True Simmer setting on all elements

Melt setting on one element

Hot surface indicators on all elements

High frequency pulsation elements improve cooking performance and control

Temperature limiter to ensure that safe operating temperature of ceramic glass is never exceeded

Child safety lock key and universal off

Model ICT15E/S

381 mm Framed

Electric Cooktop

Model ICT30E/S

762 mm Framed

Electric Cooktop

Model ICT36E/S

914 mm Framed

Electric Cooktop

This appliance is certified by

Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org.

F R A M E D E L E C T R I C C O O K T O P F E A T U R E S

Model ICT36E/S shown

Triple-zone element

Illuminated electronic touch controls

Dual-zone element

SIM

OFF

ZON

E 2

HIG

SIM

OFF

HIG

SIM

OFF

HIG

HIGH

SIM

HIG H

OFF

ZON

E 2

ZON

E 3

OFF ON

OFF universal off

True Simmer on all elements

Lock key and

M O D E L O P T I O N S

Framed Electric Cooktops

381 mm Framed Electric Cooktop

Classic Trim ICT15E/S

762 mm Framed Electric Cooktop

Classic Trim ICT30E/S

914 mm Framed Electric Cooktop

Classic Trim ICT36E/S

Framed edge Location of rating plate

Hot surface indicators

W O L F E L E C T R I C C O O K T O P S

A C C E S S O R I E S

Optional accessories are available through your Wolf dealer.

P L A N N I N G I N F O R M A T I O N

From a planning perspective, your selection process is made easier by the three different sizes you have to choose from. For ease of installation, Wolf recommends using 838 mm cabinets with the 762 mm cooktop and 991 mm cabinets with the 914 mm cooktop.

Specifications on the following pages provide overall dimensions, countertop cut-out dimensions and installation specifics for the three different-sized cooktops. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation.

A Wolf single built-in oven may be installed below these cooktops. Wolf framed electric cooktops are designed and agency approved for installation with Wolf built-in ovens only. Also, be aware of the depth of the cooktop when planning for this installation.

Multiple cooktops and/or integrated modules can be installed side by side. Refer to the countertop cut-out dimensions on page 19 when planning for this installation.

These cooktops can accommodate a Wolf cooktop hood or downdraft system. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages

57–66 for ventilation specifications.

E L E C T R I C A L R E Q U I R E M E N T S

Electric cooktops require a separate, grounded

220-240 V AC, 50/60 Hz electrical supply with its own circuit breaker. Locate electrical supply within the shaded area shown in the Installation

Specifications illustration for your model.

IMPORTANT NOTE: When an oven is installed below the cooktop, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven, unless you are using cabinets deeper than 610 mm. Refer to pages

6–7 for additional specifications for built-in ovens.

You must follow all local codes and ordinances when installing your service.

These cooktops are intended for indoor use.

A C C E S S O R I E S

Electric Cooktops

Filler strip

Bracket supports for installation of two integrated modules with downdraft (Model DD30 only)

Accessories are available through your Wolf dealer.

The proper voltage, frequency and amperage ratings are listed on the product rating plate.

W O L F E L E C T R I C C O O K T O P S

O V E R A L L D I M E N S I O N S

Model ICT15E/S

381 mm

OVERALL WIDTH

533 mm

OVERALL

DEPTH

89 mm

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

Model ICT15E/S

330 mm max

51** mm

489 mm

COOKTOP CUT-OUT

DEPTH

457 mm

64 mm min

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

838 mm RECOMMENDED

CABINET WIDTH

51 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

340 mm

COOKTOP CUT-OUT

WIDTH

102 mm

381 mm

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

M O D E L O P T I O N S

381 mm Framed Electric Cooktop

Classic Trim Finish ICT15E/S

S P E C I F I C A T I O N S

381 mm Framed Electric Cooktop

Overall Width

Overall Height

Overall Depth

Cabinet Depth

Height Clearance

Cut-Out Width*

Cut-Out Depth

Electrical Supply

Conduit

Electrical Rating

Shipping Weight

381 mm

89 mm

533 mm

Heating Elements Two

Temperature Zones Three

Max Element Power 750 W / 2200 W

(dual)

Max Element Power 1200 W

(single)

578 mm min

102 mm min

340 mm

489 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

1.2 m flexible 3-wire

3.4 kW at 240 V

14 kg

*If the 381 mm cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width increases to 356 mm.

The outer diameter of the heating elements are

229 mm and 165 mm.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

340 mm

Countertop Cut-Out Dimensions COOKTOP CUT-OUT

WIDTH

64 mm min

489 mm

COOKTOP

CUT-OUT DEPTH

FRONT OF COUNTERTOP

W O L F E L E C T R I C C O O K T O P S

O V E R A L L D I M E N S I O N S

762 mm Framed Electric Cooktop

M O D E L O P T I O N S

762 mm Framed Electric Cooktop

Classic Trim Finish ICT30E/S

S P E C I F I C A T I O N S

762 mm Framed Electric Cooktop

Overall Width

Overall Height

762 mm

89 mm

Overall Depth

Heating Elements

533 mm

Four

Temperature Zones Six

Max Element Power 750 W / 2200 W and

(two dual) 950 W / 1900 W

Max Element Power 1200 W and 1500 W

(two single)

Cabinet Width 838 mm rec

762 mm min

Cabinet Depth

Height Clearance

Cut-Out Width*

Cut-Out Depth

Electrical Supply

Conduit

Electrical Rating

Shipping Weight

578 mm min

102 mm min

721 mm

489 mm

220-240 V AC, 50/60 Hz

40 amp dedicated circuit

1.2 m flexible 3-wire

6.8 kW at 240 V

20 kg

*If the 762 mm cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width increases to 737 mm.

The outer diameter of the heating elements are

229 mm, 216 mm, 179 mm and 165 mm.

I N S T A L L A T I O N O P T I O N S

A Wolf 762 mm single oven may be installed below the Wolf 762 mm framed electric cooktop. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. A Wolf 914 mm single oven may also be installed below the Wolf 762 mm framed electric cooktop. Refer to pages 6 and 7 for additional specifications.

Refer to installation instructions shipped with each Wolf product for detailed specifications.

762 mm

OVERALL WIDTH

533 mm

OVERALL

DEPTH

89 mm

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

762 mm Framed Electric Cooktop

330 mm max

51** mm

489 mm

COOKTOP CUT-OUT

DEPTH

610 mm min

64 mm min

457 mm

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

51 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

838 mm RECOMMENDED

CABINET WIDTH

762 mm min

721 mm COOKTOP

CUT-OUT WIDTH

95 mm min

102 mm

89 mm

254 mm

762 mm OVEN OPENING

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop.

**Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

Countertop Cut-Out Dimensions

721 mm

COOKTOP CUT-OUT WIDTH

64 mm min

489 mm

COOKTOP

CUT-OUT DEPTH

FRONT OF COUNTERTOP

W O L F E L E C T R I C C O O K T O P S

O V E R A L L D I M E N S I O N S

914 mm Framed Electric Cooktop

914 mm

OVERALL WIDTH

Unit dimensions may vary to ± 3 mm.

533 mm

OVERALL

DEPTH

89 mm

I N S T A L L A T I O N S P E C I F I C A T I O N S

914 mm Framed Electric Cooktop

330 mm max

51** mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm min

457 mm

610 mm min 914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

51 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

991 mm

RECOMMENDED CABINET WIDTH

914 mm min

873 mm

COOKTOP CUT-OUT WIDTH

95 mm min

102 mm

89 mm

254 mm

914 mm OVEN OPENING

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop.

**Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

Countertop Cut-Out Dimensions

64 mm min

873 mm

COOKTOP CUT-OUT WIDTH

489 mm

COOKTOP

CUT-OUT DEPTH

M O D E L O P T I O N S

914 mm Framed Electric Cooktop

Classic Trim Finish ICT36E/S

S P E C I F I C A T I O N S

914 mm Framed Electric Cooktop

Overall Width

Overall Height

Overall Depth

914 mm

89 mm

533 mm

Heating Elements Five

Temperature Zones Eight

Max Element Power 1050 W / 2200 W /

(triple) 2700 W

Max Element Power 750 W / 2200 W

(dual)

Max Element Power 1200 W, 1500 W

(three single) and 1800 W

Cabinet Width 991 mm rec

914 mm min

Cabinet Depth

Height Clearance

578 mm min

102 mm min

Cut-Out Width*

Cut-Out Depth

Electrical Supply

Conduit

Electrical Rating

Shipping Weight

873 mm

489 mm

220-240 V AC, 50/60 Hz

50 amp dedicated circuit

1.2 m flexible 3-wire

9.4 kW at 240 V

27 kg

*If the 914 mm cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width increases to 889 mm.

The outer diameter of the heating elements are 302 mm, 232 mm, 200 mm, 181 mm and

165 mm.

I N S T A L L A T I O N O P T I O N S

A Wolf 914 mm single oven may be installed below the Wolf 914 mm framed electric cooktop. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. A Wolf 762 mm single oven may also be installed below the Wolf 914 mm framed electric cooktop. Refer to pages 6 and 7 for additional specifications.

When a 914 mm oven is installed below a cooktop, it is recommended that the rough opening for the oven be 197 mm from the floor to ease the use of the oven door.

FRONT OF COUNTERTOP

W O L F G A S C O O K T O P S

Model ICBCT15G/S

381 mm

Gas Cooktop

Model ICBCT30G/S

762 mm

Gas Cooktop

Model ICBCT36G/S

914 mm

Gas Cooktop

W O L F G A S C O O K T O P S

New features make cooking a greater pleasure than ever. For instance, at higher settings the dual-stacked burner design uses its upper-level burner for maximum heat transfer. Merely turn down the illuminated knob and the lower-tier burners deliver fine-tuning control and True

Simmer. You’ll see why we patented this concept when you can have the slightest of flame and enjoy a simmer with no boiling or scorching. This is heat tailored for every cooking vessel you’re using—from the largest stockpot to the smallest melting pan.

A more powerful 5.0 kW burner is standard on the 762 mm and 914 mm gas cooktops.

The dual-stacked sealed burners and deep recess of the seamless drawn pan area make cleanup of any of those previously unsightly spills a snap.

F E A T U R E S

Available in natural and LP gas

Stainless steel top construction, available in classic stainless steel finish

Dual-stacked, sealed burners with automatic reignition on all settings

Large 5.0 kW burner with .2 kW delivered at simmer—Models ICBCT30G/S and ICBCT36G/S only

Medium 4.0 kW burner with .2 kW delivered at simmer

Small 3.2 kW burners with .1 kW delivered at simmer

Electronic spark ignition system

True Simmer setting on all burners

Illuminated control panel with two-tiered control knobs

Low-profile, cast iron continuous burner grates with matte porcelain finish

Seamless drawn burner pan

CE certified

This appliance is certified by

Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org.

G A S C O O K T O P F E A T U R E S

Model ICBCT36G/S shown

Small 3.2 kW burners

Low-profile continuous grates

Seamless drawn pan

Two-tiered control knobs

Large 5.0 kW burner

Illuminated control panel

Medium 4.0 kW burner

Location of rating plate

M O D E L O P T I O N S

Gas Cooktops

381 mm Gas Cooktop

Classic Stainless ICBCT15G/S

762 mm Gas Cooktop

Classic Stainless ICBCT30G/S

914 mm Gas Cooktop

Classic Stainless ICBCT36G/S

W O L F G A S C O O K T O P S

P L A N N I N G I N F O R M A T I O N

Wolf recommends using 838 mm cabinets with the 762 mm cooktop and 991 mm cabinets with the 914 mm cooktop.

A Wolf single built-in oven may be installed below these cooktops. Wolf gas cooktops are designed and agency approved for installation with Wolf built-in ovens only. Also, be aware of the depth of the cooktop when planning for this installation.

Multiple cooktops and/or integrated modules can be installed side by side. Refer to the countertop cut-out dimensions on page 19 when planning for this installation.

57–66 for ventilation specifications.

E L E C T R I C A L | G A S R E Q U I R E M E N T S

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

Wolf gas cooktops are designed to operate on natural gas, I2H, I2E, and I2E+ at 20 mb pressure or LP (propane) gas at 37 mb WC pressure. They are supplied with an ISO 14 male gas connection at the right rear corner on the bottom of the cooktop. The male connector exits the unit straight down.

Locate electrical and gas supply within the shaded area shown in the Installation Specifications illustration for your model.

6–7 for additional specifications for built-in ovens.

When a gas cooktop is installed above cabinets, the gas and electrical placement is not critical.

A grounded outlet needs to be placed within

1.2 m of the right rear of the cooktop.

You must follow all local codes and ordinances when installing your services.

These cooktops are intended for indoor use.

A C C E S S O R I E S

Gas Cooktops

One-piece wok and single burner grate (Models ICBCT30G/S and

ICBCT36G/S)

Filler strip

Bracket supports for installation of two integrated modules with downdraft (Model DD30 only)

Accessories are available through your Wolf dealer.

W O L F G A S C O O K T O P S

O V E R A L L D I M E N S I O N S

381 mm Gas Cooktop

M O D E L O P T I O N S

381 mm Gas Cooktop

Classic / Natural Gas ICBCT15G/S

Classic / LP Gas ICBCT15G/S-LP

S P E C I F I C A T I O N S

381 mm Gas Cooktop

Overall Width

Overall Height

Overall Depth

Burner Rating

Cabinet Depth

Height Clearance

Cut-Out Width

Cut-Out Depth

Electrical Supply

Gas Rating

Shipping Weight

381 mm

102 mm

533 mm

(1) 4.0 kW with .2 kW delivered at simmer

(1) 3.2 kW with .1 kW delivered at simmer

578 mm min

102 mm min

356 mm

489 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

7.2 kW

14 kg

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N O P T I O N S

For the 381 mm gas cooktop, the gas service may be supplied through the floor if the cooktop is not installed above an oven. Refer to the illustration for specifics on placement of gas and electrical.

Refer to installation instructions shipped with each Wolf product for detailed specifications.

381 mm

OVERALL WIDTH

533 mm

OVERALL

DEPTH

102 mm

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

381 mm Gas Cooktop

330 mm max

64** mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm min

457 mm

838 mm RECOMMENDED

CABINET WIDTH

178 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

356 mm

COOKTOP CUT-OUT

WIDTH

102 mm

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

127 mm

LOCATION OF GAS

SUPPLY MAY ALSO

EXTEND 127 mm

ON FLOOR

FROM BACK WALL

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

E G

381 mm

LOCATION OF GAS SUPPLY

MAY ALSO EXTEND 127 mm ON

FLOOR FROM BACK WALL

381 mm

NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 33" (838) recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

Countertop Cut-Out Dimensions

356 mm

COOKTOP CUT-OUT

WIDTH

64 mm min

489 mm

COOKTOP

CUT-OUT DEPTH

FRONT OF COUNTERTOP

W O L F G A S C O O K T O P S

O V E R A L L D I M E N S I O N S

762 mm Gas Cooktop

762 mm

OVERALL WIDTH

533 mm

OVERALL

DEPTH

102 mm

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

762 mm Gas Cooktop

330 mm max

64** mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm min

457 mm

610 mm min 914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

229 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

838 mm RECOMMENDED

CABINET WIDTH

762 mm min

737 mm COOKTOP

CUT-OUT WIDTH

95 mm min

102 mm

89 mm E

254 mm

762 mm OVEN OPENING

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

M O D E L O P T I O N S

762 mm Gas Cooktop

Classic / Natural Gas ICBCT30G/S

Classic / LP Gas ICBCT30G/S-LP

S P E C I F I C A T I O N S

762 mm Gas Cooktop

Overall Width

Overall Height

Overall Depth

Burner Rating

Cabinet Width

Cabinet Depth

Height Clearance

Cut-Out Width

Cut-Out Depth

Electrical Supply

Gas Rating

Shipping Weight

762 mm

102 mm

533 mm

(1) 5.0 kW with .2 kW delivered at simmer

(1) 4.0 kW with .2 kW delivered at simmer

(2) 3.2 kW with .1 kW delivered at simmer

838 mm rec

762 mm min

578 mm min

102 mm min

737 mm

489 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

15.4 kW

23 kg

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N O P T I O N S

A Wolf 762 mm single oven may be installed below the Wolf 762 mm gas cooktop. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical and gas supply be placed in the base cabinet to the right of the oven. Refer to page 6 for additional specifications.

*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop.

**Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

Countertop Cut-Out Dimensions

737 mm

COOKTOP CUT-OUT WIDTH

64 mm min

489 mm

COOKTOP

CUT-OUT DEPTH

FRONT OF COUNTERTOP

W O L F G A S C O O K T O P S

O V E R A L L D I M E N S I O N S

914 mm Gas Cooktop

M O D E L O P T I O N S

914 mm Gas Cooktop

Classic / Natural Gas ICBCT36G/S

Classic / LP Gas ICBCT36G/S-LP

533 mm

OVERALL

DEPTH

S P E C I F I C A T I O N S

914 mm Gas Cooktop

Overall Width

Overall Height

Overall Depth

Burner Rating

Cabinet Width

Cabinet Depth

Height Clearance

Cut-Out Width

Cut-Out Depth

Electrical Supply

Gas Rating

Shipping Weight

914 mm

OVERALL WIDTH

914 mm

102 mm

533 mm

(1) 5.0 kW with .2 kW delivered at simmer

(1) 4.0 kW with .2 kW delivered at simmer

(3) 3.2 kW with .1 kW delivered at simmer

991 mm rec

914 mm min

578 mm min

102 mm min

889 mm

489 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

18.6 kW

30 kg

Unit dimensions may vary to ± 3 mm.

102 mm

I N S T A L L A T I O N S P E C I F I C A T I O N S

914 mm Gas Cooktop

I N S T A L L A T I O N O P T I O N S

A Wolf 914 mm single oven may be installed below the Wolf 914 mm gas cooktop. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical and gas supply be placed in the base cabinet to the right of the oven. A Wolf

762 mm single oven may also be installed below the Wolf 914 mm gas cooktop. Refer to pages 6 and 7 for additional specifications.

When a 914 mm oven is installed below a cooktop, it is recommended that the rough opening for the oven be 197 mm from the floor to ease the use of the oven door.

Refer to installation instructions shipped with each Wolf product for detailed specifications.

330 mm max

64** mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm min

457 mm

610 mm min 914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

229 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

991 mm

RECOMMENDED CABINET WIDTH

914 mm min

889 mm

COOKTOP CUT-OUT WIDTH

95 mm min

102 mm

89 mm E G

254 mm

914 mm OVEN OPENING

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop.

**Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

Countertop Cut-Out Dimensions

889 mm

COOKTOP CUT-OUT WIDTH

64 mm min

489 mm

COOKTOP

CUT-OUT DEPTH

FRONT OF COUNTERTOP

W O L F I N T E G R A T E D M O D U L E S

With Wolf‘s integrated modules, you have the ultimate in customization. You can create your own design by mixing and matching the various components within this system. And when you couple these modules with other cooktops within the Wolf inventory, you and your client will truly understand freedom of choice.

Some modules integrate with their larger counterparts, right down to their low-profile grates, dual-stacked gas burners, deep spill pan and illuminated controls. The two-element electric and dual-stacked sealed burner gas cooktop modules deliver the same performance and appearance as the larger electric and gas cooktops.

Some integrated modules can be installed together or with a 762 mm or 914 mm cooktop.

When multiple cooktops or modules are installed side by side, the cut-out dimensions shown in the illustration below are derived by adding

32 mm additional space for each additional unit, to give you your total cut-out width.

IMPORTANT NOTE: Refer to specifications on the following pages for specific installation requirements and limitations for each integrated module. Review specific installation instructions for product-to-product capabilities. Additional information is provided in the specifications pdf files on our website, wolfappliance.com

Refer to the following illustration for countertop cut-out dimensions for the installation of multiple cooktops or modules.

IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, each unit must have its own separate recommended electrical circuit. When multiple gas cooktops or modules are installed next to one another, they can receive their gas supply from a common line.

However, each unit must have its own regulator installed between the mainline and the cooktop or module.

Model CT15I/S

Induction Cooktop

Model ICT15E/S

Electric Cooktop

Model ICBIG15/S

Electric Grill

These integrated modules are intended for indoor use.

Model ICBIS15/S

Electric Steamer

C O U N T E R T O P C U T - O U T D I M E N S I O N S

Installation of Multiple Cooktops or Modules

1518 mm – FOUR MODULES WIDTH OR

1511 mm – 762 mm COOKTOP AND TWO MODULES OR

1276 mm – 914 mm COOKTOP AND ONE MODULE

1130 mm – THREE MODULES WIDTH OR

1124 mm – 762 mm COOKTOP AND ONE MODULE

743 mm

TWO MODULES WIDTH

64 mm min

356 mm

CUT-OUT

WIDTH

489 mm

CUT-OUT

DEPTH

FRONT OF COUNTERTOP

IMPORTANT NOTE: When two or more modules are installed together, an integrated module filler strip is recommended. If a Model DD30 downdraft system is also installed, an integrated module support for downdraft ventilation is required. Contact your Wolf dealer for information on these accessory components.

Model ICBIF15/S

Electric Fryer

I N T E G R A T E D M O D U L E S

381 mm Width

Induction Cooktop

Electric Cooktop

Electric Grill

Electric Steamer

Electric Fryer

Gas Cooktop

Gas Multi-Function

Cooktop

CT15I/S

ICT15E/S

ICBIG15/S

ICBIS15/S

ICBIF15/S

ICBCT15G/S

IIM15/S

All integrated modules are available in the classic stainless steel finish.

IMPORTANT NOTE: Refer to specifications on the following pages for specific installation requirements and limitations for each integrated module. Specifications for Model ICT15E/S are found on page 11 and Model ICBCT15G/S specifications are on page 16.

Model ICBCT15G/S

Gas Cooktop

Model IIM15/S

Gas Multi-Function

Cooktop

W O L F I N T E G R A T E D M O D U L E S

Model CT15I/S

Induction Cooktop

I N D U C T I O N C O O K T O P

While induction cooking is new to North

America, it has been used in Europe for decades by professionals and homeowners demanding the best in performance.

Cooking with this sleek 15-inch powerhouse is simply the best way to cook. Electricity flows through a coil to produce a magnetic field under the sleek black ceramic top. When an iron or magnetic stainless steel pan is placed on the surface, the magnetic field creates a current in the pan, exciting the molecules and heating the pan and not the cooktop. That‘s why the cooktop stays cool to the touch and the food cooks efficiently.

In fact, this unit is so efficient that it outperforms gas and electric cooktops. There is no wasted heat because energy is supplied directly to the cooking vessel, so nearly 90 percent of the energy gets used to cook.

You can keep sauces and chocolates melted at

50 watts of power, or with the touch of a finger, activate the hi-power boost feature and boil water in nearly half the time you normally do.

The Wolf induction cooktop has it all.

F E A T U R E S

Integrated design allows for installation of multiple cooktops or modules

Classic stainless steel trim finish

Easy-to-clean black ceramic glass surface is resistant to scratching, staining, impact and heat

Induction elements heat cookware not the glass, for a cooler and safer cooking surface

Cookware sensing—elements will not be energized without an iron or magnetic stainless steel pan on the cooktop surface

Illuminated electronic touch controls with graduated control lighting

High-efficiency elements deliver power and control

Hi-Power mode boosts power on rear element to 2200 W maximum power output by diverting power from front element

Simultaneous operation of both elements at

1800 W each

True Simmer setting on both elements

Melt setting on both elements

Temperature limiter to ensure that safe operating temperature of ceramic glass is never exceeded

Child safety lock key and universal off

I N D U C T I O N C O O K T O P F E A T U R E S

Model CT15I/S

Two induction elements

Illuminated electronic touch controls

Lock key and universal off

OFF

HI-POWER

HIG

SIM

OFF

O V E R A L L D I M E N S I O N S

Model CT15I/S

Classic stainless steel trim finish

Location of rating plate

True Simmer and melt on both elements

533 mm

OVERALL

DEPTH

381 mm

OVERALL WIDTH

64 mm

A C C E S S O R I E S

Induction Cooktop

Filler strip

Bracket supports for installation of two integrated modules with

762 mm downdraft

Accessories are available through your Wolf dealer.

W O L F I N T E G R A T E D M O D U L E S

P L A N N I N G I N F O R M A T I O N

The illustrations provide the overall dimensions and finished cut-out dimensions that you need to plan for in your installation. We have minimized the information contained in the illustrations, concentrating on the critical information you must plan into your installation.

IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, refer to page

19 for countertop cut-out dimensions.

The induction cooktop can accommodate a

Wolf cooktop hood or downdraft system. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages

57–66 for ventilation specifications.

E L E C T R I C A L R E Q U I R E M E N T S

The Wolf induction cooktop requires a separate, grounded 3-wire 220-240 V AC, 50/60 Hz, 20 amp service with its own circuit breaker. Locate electrical within the shaded area shown in the illustration.

You must follow all local codes and ordinances when installing your service.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

I N S T A L L A T I O N S P E C I F I C A T I O N S

Model CT15I/S

330 mm max

51** mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm min

457 mm

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

838 mm RECOMMENDED

CABINET WIDTH

51 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

340 mm

COOKTOP CUT-OUT

WIDTH

114 mm

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

381 mm

340 mm

Countertop Cut-Out Dimensions

64 mm min

COOKTOP CUT-OUT

WIDTH

489 mm

COOKTOP

CUT-OUT DEPTH

FRONT OF COUNTERTOP

S P E C I F I C A T I O N S

Model CT15I/S

Induction Cooktop

Trim Finish

Overall Width

Overall Height

Overall Depth

Classic

381 mm

64 mm

533 mm

Induction Elements Two

Max Element Power 1800 W

(front)

Max Element Power 2200 W

(rear)

Cabinet Depth

Height Clearance

Cut-Out Width*

Cut-Out Depth

Electrical Supply

578 mm min

152 mm min

340 mm

489 mm

220-240 V AC, 50/60 Hz

20 amp dedicated circuit

Conduit

Electrical Rating

Shipping Weight

1.2 m flexible 3-wire

3.4 kW

14 kg

*If the induction cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width increases to 356 mm.

IMPORTANT NOTE: A minimum height clearance of 152 mm is required. If a shelf is installed below the unit, a 25 mm gap at the rear of the cabinet shelf is necessary to allow for proper ventilation. Failure to do so could result in decreased performance or product damage.

Unit dimensions may vary to ± 3 mm.

W O L F I N T E G R A T E D M O D U L E S

Model ICBIG15/S

Electric Grill Module

E L E C T R I C G R I L L M O D U L E

Who says you have to sacrifice the fun of grilling when the weather changes and you cannot take advantage of the outdoors? With this grill cooktop you can easily handle steaks and all sorts of food without the hassle of lava rocks or briquettes.

There are two individual heating elements—front and back—on this module that enable you to cook on one side while keeping other items at serving temperature.

For ease of cleaning, there are porcelainized plates below two 1400-watt heating elements that accumulate any unwanted grease and drain it away.

The Wolf electric grill module is available in classic stainless steel.

F E A T U R E S

Integrated design allows for installation of multiple cooktops or modules

Stainless steel top construction with classic stainless steel finish

Two 1400-watt, individually controlled heating elements—front and back—for even grilling

Illuminated electronic touch controls with graduated control lighting

Low-profile, one-piece cast iron grilling grate with matte porcelain finish

Black porcelain-coated grease deflection plates

Easy-to-clean, removable porcelain collection pan

Independent digital timer

CE certified

This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org.

E L E C T R I C G R I L L F E A T U R E S

Model ICBIG15/S

Low-profile, one-piece grilling grate

Two 1400-watt heating elements

Illuminated electronic touch controls

O V E R A L L D I M E N S I O N S

Model ICBIG15/S

533 mm

OVERALL

DEPTH

381 mm

OVERALL WIDTH

159 mm

Removable collection pan

Graduated control lighting

Location of rating plate

A C C E S S O R I E S

Electric Grill Module

Filler strip

Accessories are available through your Wolf dealer.

W O L F I N T E G R A T E D M O D U L E S

P L A N N I N G I N F O R M A T I O N

IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, refer to page

19 for countertop cut-out dimensions.

The grill module can accommodate a Wolf cooktop hood. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications.

IMPORTANT NOTE: Wolf does not recommend the use of downdraft ventilation with the grill module.

E L E C T R I C A L R E Q U I R E M E N T S

The Wolf International electric grill module is CB approved and and is manufactured for a 220-240

V AC, 50/60 Hz electrical supply. Locate electrical within the shaded area shown in the illustration.

You must follow all local codes and ordinances when installing your service.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

I N S T A L L A T I O N S P E C I F I C A T I O N S

Model ICBIG15/S

330 mm max

51** mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm min

457 mm

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

838 mm RECOMMENDED

CABINET WIDTH

178 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

356 mm

COOKTOP CUT-OUT

WIDTH

159 mm

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

381 mm

S P E C I F I C A T I O N S

Model ICBIG15/S

Electric Grill Module

Exterior Finish

Overall Width

Overall Height

Overall Depth

Electrical Rating

Shipping Weight

Classic

381 mm

159 mm

533 mm

Temperature Zones Two

Heating Element

Zone (front)

1400 W

Heating Element

Zone (rear)

1400 W

Total Element Power 2800 W

Cabinet Depth 578 mm min

Height Clearance

Cut-Out Width

Cut-Out Depth

Electrical Supply

159 mm min

356 mm

489 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

2.8 kW

28 kg

Unit dimensions may vary to ± 3 mm.

356 mm

Countertop Cut-Out Dimensions

COOKTOP CUT-OUT

WIDTH

64 mm min

489 mm

COOKTOP

CUT-OUT DEPTH

FRONT OF COUNTERTOP

W O L F I N T E G R A T E D M O D U L E S

Model ICBIS15/S

Electric Steamer

Module

E L E C T R I C S T E A M E R M O D U L E

From a temperature of 60˚C to boil, you can keep food hot for long periods of time or defrost easily without drying out or losing flavor.

The beauty of this steamer module is accented by the sculptured glass domed lid, which is easily inverted for storage to keep a low profile.

The deep, large vessel with a 7.6 L capacity can hold up to 3.3 L of cooked pasta. Includes one solid and one perforated stackable insert pan.

The diversity of our electric steamer includes slow cooking, double boiling, steaming eggs, steaming custard, proofing bread dough, warming food and melting chocolate as well as steaming vegetables.

The Wolf electric steamer module is available in classic stainless steel.

This steamer module must be installed at least 381 mm away from a Wolf fryer module, as contact between water and hot oil may cause burns from steam and hot oil.

F E A T U R E S

Integrated design allows for installation of multiple cooktops or modules

Stainless steel top construction with classic stainless steel finish

Hidden 2600-watt heating element

Illuminated electronic touch controls with graduated control lighting

Large 7.6 L maximum capacity tub—2.4 L capacity for steaming

Two stackable stainless steel steamer insert pans—one solid and one perforated

Uses include steaming vegetables, eggs and custard, double boiling, proofing bread dough, warming food and melting chocolate

Can function as a slow cooker for 8–10 hours

Reversible domed glass lid for easy storage

Independent digital timer

Digital temperature readout and preheat indicator

Electronic drain

CE certified

This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org.

O V E R A L L D I M E N S I O N S

Model ICBIS15/S

E L E C T R I C S T E A M E R F E A T U R E S

Model ICBIS15/S

Reversible domed glass lid

Hidden 2600-watt heating element

Illuminated electronic touch controls

533 mm

OVERALL

DEPTH

381 mm

OVERALL WIDTH

Deep drawn pan Location of rating plate

Digital temperature readout

Graduated control lighting 191 mm

343 mm

TO DRAIN

OUTLET

A C C E S S O R I E S

Electric Steamer Module

Filler strip

Accessories are available through your Wolf dealer.

W O L F I N T E G R A T E D M O D U L E S

P L A N N I N G I N F O R M A T I O N

The illustrations provide the overall dimensions and finished cut-out dimensions that you need to plan for in your installation.

IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, refer to page

19 for countertop cut-out dimensions.

For the drain connection, the 16 mm outlet from the valve will accept a drain hose that must flow downward to, and tie into, an existing sink drain.

A separate drain with a freefall may also be installed. (Following local building codes, your plumber will dictate how to plumb the unit.) As a third option, the consumer will supply a heat resistant bucket for drainage in the location of the drain outlet. Refer to the illustration for location of the drain outlet.

The steamer module can accommodate a Wolf cooktop hood. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications.

IMPORTANT NOTE: Wolf does not recommend the use of downdraft ventilation with the steamer module.

I N S T A L L A T I O N

E L E C T R I C A L R E Q U I R E M E N T S

The Wolf International electric steamer module is

CB approved and and is manufactured for a

220-240 V AC, 50/60 Hz electrical supply. Locate electrical within the shaded area shown.

You must follow all local codes and ordinances when installing your service.

Refer to installation instructions shipped with each Wolf product for detailed specifications.

I N S T A L L A T I O N S P E C I F I C A T I O N S

Model ICBIS15/S

330 mm max

51** mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm min

457 mm

314 mm

194 mm

DRAIN OUTLET

LOCATION

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

838 mm RECOMMENDED

CABINET WIDTH

178 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

356 mm

COOKTOP CUT-OUT

WIDTH

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

314 mm

152 mm

343 mm

DRAIN

OUTLET

LOCATION

381 mm

Countertop Cut-Out Dimensions

356 mm

COOKTOP CUT-OUT

WIDTH

64 mm min

489 mm

COOKTOP

CUT-OUT DEPTH

FRONT OF COUNTERTOP

S P E C I F I C A T I O N S

Model ICBIS15/S

Electric Steamer Module

Exterior Finish

Overall Width

Overall Height

Overall Depth

Heating Element

Cabinet Depth

Height Clearance

Cut-Out Width

Cut-Out Depth

Electrical Supply

Electrical Rating

Shipping Weight

Classic

381 mm

343 mm

533 mm

2600 W

578 mm min

343 mm min

356 mm

489 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

2.6 kW

18 kg

Unit dimensions may vary to ± 3 mm.

This steamer module must be installed at least 381 mm away from a Wolf fryer module, as contact between water and hot oil may cause burns from steam and hot oil.

W O L F I N T E G R A T E D M O D U L E S

Model ICBIF15/S

Electric Fryer Module

E L E C T R I C F R Y E R M O D U L E

To round out your options for the ideal kitchen, you can choose a fryer, and Wolf offers a great option that the market has never seen. When your clients use this module, they‘ll be able to create dinner specialties never tried before.

The accurate temperature control will enable your customer to seal in that great flavor of the food without absorbing any unnecessary grease.

The fryer can handle a variety of foods at a wide range of oil temperatures.

The Wolf fryer module is available in classic stainless steel. In addition, there is a metal storage lid to keep the grease area free from particles falling into the fryer.

This fryer module must be installed at least

381 mm away from any open flame cooking device. The open flame may cause ignition of oil.

F E A T U R E S

Integrated design allows for installation of multiple cooktops or modules

Stainless steel top construction with classic stainless steel finish

Hidden 2600-watt heating element

Illuminated electronic touch controls with graduated control lighting

Large 3.8 L capacity tub

Three baskets included—one large and two small side by side, each with wire basket hanger

Low-profile lid

Melt feature for shortening or lard

Independent digital timer

Digital temperature readout and preheat indicator

Easy manual locking drain capability

Recommended for installation with any Wolf framed electric cooktop or the Wolf electric grill module

CE certified

This fryer module must be installed at least

381 mm away from a Wolf steamer module, as contact between water and hot oil may cause burns from steam and hot oil.

E L E C T R I C F R Y E R F E A T U R E S

Model ICBIF15/S

Low-profile lid Hidden 2600-watt heating element

Illuminated electronic touch controls

Deep drawn pan Location of rating plate

Digital temperature readout

Graduated control lighting

O V E R A L L D I M E N S I O N S

Model ICBIF15/S

533 mm

OVERALL

DEPTH

191 mm

381 mm

OVERALL WIDTH

343 mm

TO DRAIN

OUTLET

A C C E S S O R I E S

Electric Fryer Module

Filler strip

Accessories are available through your Wolf dealer.

W O L F I N T E G R A T E D M O D U L E S

P L A N N I N G I N F O R M A T I O N

The illustrations provide the overall dimensions and finished cut-out dimensions that you need to plan for in your installation.

IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, refer to page

19 for countertop cut-out dimensions.

The electric fryer module must be installed in a base cabinet with access to the bottom of the unit to drain the oil through a manual valve. The consumer must supply a heat resistant bucket to accept the drained oil. Refer to the illustration for location of the drain outlet.

The fryer module can accommodate a Wolf cooktop hood. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications.

IMPORTANT NOTE: Wolf does not recommend the use of downdraft ventilation with the fryer module.

E L E C T R I C A L R E Q U I R E M E N T S

The Wolf International electric fryer module is CB approved and and is manufactured for a 220-240

V AC, 50/60 Hz electrical supply. Locate electrical within the shaded area shown in the illustration.

You must follow all local codes and ordinances when installing your service.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

I N S T A L L A T I O N S P E C I F I C A T I O N S

Model ICBIF15/S

330 mm max

51** mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm min

457 mm

314 mm

194 mm

DRAIN OUTLET

LOCATION

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

838 mm RECOMMENDED

CABINET WIDTH

178 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

356 mm

COOKTOP CUT-OUT

WIDTH

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

DRAIN OUTLET

LOCATION

314 mm

152 mm

343 mm

381 mm

NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. NOTE: Fryer module must be installed in a base cabinet with access to manual valve at base of unit to drain oil into heat resistant receptacle. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

Countertop Cut-Out Dimensions

356 mm

COOKTOP CUT-OUT

WIDTH

S P E C I F I C A T I O N S

Model ICBIF15/S

Electric Fryer Module

Exterior Finish

Overall Width

Overall Height

Overall Depth

Heating Element

Cabinet Depth

Height Clearance

Cut-Out Width

Cut-Out Depth

Electrical Supply

Electrical Rating

Shipping Weight

Classic

381 mm

343 mm

533 mm

2600 W

578 mm min

343 mm min

356 mm

489 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

2.6 kW

14 kg

Unit dimensions may vary to ± 3 mm.

This fryer module must be installed at least 381 mm away from any open flame cooking device. The open flame may cause ignition of oil.

64 mm min

489 mm

COOKTOP

CUT-OUT DEPTH

This fryer module must be installed at least 381 mm away from a Wolf steamer module, as contact between water and hot oil may cause burns from steam and hot oil.

FRONT OF COUNTERTOP

W O L F I N T E G R A T E D M O D U L E S

Model IIM15/S

Gas Multi-Function

Cooktop

G A S M U L T I - F U N C T I O N C O O K T O P

It’s really a misnomer to describe this wonderful cooktop module as a wok instrument because it is much more than that. The large, low-profile grate will fit in nicely with any Wolf gas cooktop.

For true wok cooking, the burner sculpts the gas flame into a plume, focusing heat in the center of the wok, then dispersing it outward for precisely controlled cooking. The larger grate will handle your wok perfectly but will also accommodate your largest stockpots and Dutch ovens.

The powerful burner exceeds 5.3 kW.

The Wolf multi-function cooktop is available in classic stainless steel.

F E A T U R E S

Integrated design allows for installation of multiple cooktops or modules

Available in natural and LP gas

Stainless steel top construction with classic stainless steel finish

High output 5.3 kW burner

Automatic electronic reignition system

Illuminated control panel

Individual spark ignition system

Two interchangeable cast iron burner grates with matte porcelain finish—wok grate and lowprofile continuous grate

Deep drawn burner pan

G A S M U L T I - F U N C T I O N C O O K T O P F E A T U R E S

Model IIM15/S

High-output

5.3 kW burner

Wok grate shown

Deep drawn pan

Location of rating plate

Continuous control knob

Illuminated control panel

O V E R A L L D I M E N S I O N S

Gas Multi-Function Cooktop

533 mm

OVERALL

DEPTH

381 mm

OVERALL WIDTH

127 mm

A C C E S S O R I E S

Gas Multi-Function Cooktop

Filler strip

Bracket supports for installation of two integrated modules with

762 mm downdraft

Accessories are available through your Wolf dealer.

W O L F I N T E G R A T E D M O D U L E S

P L A N N I N G I N F O R M A T I O N

The illustrations provide the overall dimensions and finished cut-out dimensions that you need to plan for in your installation.

IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, refer to page

19 for countertop cut-out dimensions.

This cooktop can accommodate a Wolf cooktop hood or downdraft system. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications.

E L E C T R I C A L | G A S R E Q U I R E M E N T S

The Wolf International gas multifunction cooktop is CB approved and and is manufactured for a

220-240 V AC, 50/60 Hz electrical supply. Locate electrical within the shaded area shown. You must follow all local codes and ordinances when installing your service.

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

The gas multi-function cooktop is designed to operate on natural gas at 12.5 mb or LP (propane) gas at 25 mb. The minimum line pressure for natural gas is 17.5 mb and 27.4 mb for LP gas.

The maximum gas supply pressure to the regulator should never exceed 34.9 mb. It is supplied with an ISO 14 male gas connection at the right rear corner of the module. The male connector exits the unit straight down, and you are supplied with a regulator with two female connectors.

I N S T A L L A T I O N S P E C I F I C A T I O N S

Gas Multi-Function Cooktop

330 mm max

64** mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm min

457 mm

838 mm RECOMMENDED

CABINET WIDTH

178 mm min*

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

356 mm

COOKTOP CUT-OUT

WIDTH

127 mm

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

127 mm

LOCATION OF GAS

SUPPLY MAY ALSO

EXTEND 127 mm

ON FLOOR

FROM BACK WALL

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

E G

381 mm

LOCATION OF GAS SUPPLY

MAY ALSO EXTEND 127 mm ON

FLOOR FROM BACK WALL

381 mm

356 mm

COOKTOP CUT-OUT

Countertop Cut-Out Dimensions

WIDTH

M O D E L O P T I O N S

Gas Multi-Function Cooktop

Classic / Natural Gas IIM15/S

Classic / LP Gas IIM15/S-LP

S P E C I F I C A T I O N S

Gas Multi-Function Cooktop

Overall Width

Overall Height

Overall Depth

Burner Rating

Cabinet Depth

Height Clearance*

Cut-Out Width

Cut-Out Depth

Electrical Supply

Gas Rating

Shipping Weight

381 mm

127 mm

533 mm

5.3 kW

578 mm min

127 mm min

356 mm

489 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

5.3 kW

14 kg

*A minimum height clearance of 140 mm is required between countertop and any combustible surface directly below the cooktop.

Unit dimensions may vary to ± 3 mm.

64 mm min

489 mm

COOKTOP

CUT-OUT DEPTH

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

FRONT OF COUNTERTOP

W O L F W A R M I N G D R A W E R S

Model ICBWWD30 with Stainless Steel

Drawer Front

Model ICBWWD30 with Integrated

Drawer Front

W O L F W A R M I N G D R A W E R

Warming drawers have a clear mission in life— to take good care of good food until it’s time for you to eat. Our superior air control helps keep moist foods moist and crisp foods crisp. In addition, Wolf warming drawers are among the most spacious on the market, so you will have little problem storing items.

There is a rack for stacking food plus an optional set of six stainless steel containers with lids that divide the drawer into sections, keeping different dishes warm at the same time.

Electronic controls are hidden regardless of your panel selection. Choose from the classic stainless steel look or the integrated drawer front, which allows for a custom wood panel. Wolf offers optional decorative handles for the integrated drawer front. Keep in mind, there are significant changes to the installation procedure if you plan on using the integrated drawer front.

F E A T U R E S

Stainless steel drawer front and tubular handle

Integrated drawer front allows for custom wood panel application

850-watt heating element

Hidden electronic touch control panel

Preset and variable temperature control

Preset automatic shut-off or extended operation in Sabbath Mode

Stainless steel interior

Rack for stacking food

Removable stainless steel drawer pan

Full-extension, ball bearing drawer glides

CE certified

This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org.

W A R M I N G D R A W E R F E A T U R E S

Model ICBWWD30

(stainless steel drawer front shown)

Removable stainless steel drawer pan

Galvanized exterior

Rack for stacking food

Stainless steel interior

Hidden electronic touch control panel

Ball bearing drawer glides

Location of rating plate

Stainless steel drawer front shown

(sold as an accessory)

A C C E S S O R I E S

Warming Drawer

Six-piece container set—includes six stainless steel pans with lids; one 6.3 L pan, one

3.9 L pan, two 2.8 L pans, two

1.7 L pans and pan rack

Accessories are available through your Wolf dealer.

W O L F W A R M I N G D R A W E R S

P L A N N I N G I N F O R M A T I O N

The Wolf 762 mm warming drawer is shipped without any decorative drawer front. You must order a stainless steel drawer front (tubular handle included) or the integrated front (no handle) for a custom wood application.

Specifications on the following pages provide overall dimensions, rough openings and installation options for Model ICBWWD30 with stainless steel and integrated drawer fronts. Note that there are significant differences to the installation requirements for the integrated drawer front.

An anti-tip block or platform must be installed to prevent the unit from tipping forward when the drawer is opened.

The base platform must be able to support

91 kg. This platform must be a minimum of

25 mm above the toe kick to allow for the

16 mm overlap of the warming drawer trim.

Model ICBWWD30 may be installed below a

Wolf built-in oven or an electric or gas cooktop, provided the warming drawer is fully enclosed, top and bottom. It may also be installed next to or above another Model ICBWWD30. Dimensions will vary according to the specific installation.

S T A I N L E S S S T E E L D R A W E R F R O N T

Wolf recommends using a 838 mm wide cabinet for the warming drawer with stainless steel drawer front. A minimum 762 mm wide by

610 mm deep cabinet is required.

I N T E G R A T E D D R A W E R F R O N T

IMPORTANT NOTE: A minimum 838 mm wide cabinet is required for the warming drawer with integrated drawer front. A minimum 610 mm deep cabinet is required for an overlay application and 635 mm deep cabinet for a flush inset application.

Model ICBWWD30 with integrated drawer front can accommodate installations with a 762 mm or 914 mm cooktop. It may also be installed in combination with a 762 mm single or double oven or a 914 mm single oven. Dimensions will vary according to the specific installation.

Keep in mind that the width of the custom panel for the warming drawer with integrated drawer front will vary according to the specific installation. The opening width will remain 749 mm whether installed in combination with a 762 mm or 914 mm cooktop or oven.

The decorative wood drawer front panel must be a minimum of 16 mm thick.

E L E C T R I C A L R E Q U I R E M E N T S

Model ICBWWD30 is CB approved and manufactured for a 220-240 V AC, 50/60 Hz electrical supply. The service should have its own 15 or

20 amp circuit breaker, and a grounded 3-prong receptacle should be located within reach of the power cord and flush with the back wall. Locate electrical within the shaded area shown in the installation illustrations on the following pages.

A C C E S S O R I E S

Optional accessories are available through your Wolf dealer.

O V E R A L L D I M E N S I O N S

Model ICBWWD30 with Stainless Steel Drawer Front

689 mm

OVERALL DEPTH

260 mm 229 mm

759 mm

OVERALL WIDTH

597 mm

BEHIND FRAME

Model ICBWWD30 with Integrated Drawer Front

257 mm 229 mm

746 mm

OVERALL WIDTH

597 mm

BEHIND FRAME

F R O N T P A N E L O P T I O N S

Model ICBWWD30

Classic Stainless WWDFRONT/S

Integrated WWDFRONT/I

(accepts wood panel)

Optional drawer front panels are ordered and shipped as sales accessories. Stainless steel drawer front panels include matching tubular handle.

W O L F W A R M I N G D R A W E R S

S P E C I F I C A T I O N S

Model ICBWWD30 with

Stainless Steel Drawer Front

Overall Width

Overall Height

Overall Depth

(behind frame)

Interior Capacity

Cabinet Width

759 mm

260 mm

597 mm

Cabinet Depth

Min Base Support

Opening Width

Opening Height

Opening Depth

Electrical Supply

Heating Element

Shipping Weight

45 L

838 mm rec

762 mm min

610 mm min

91 kg

727 mm

232 mm

606 mm

220-240 V AC, 50/60 Hz

15 or 20 amp circuit

850 W

45 kg

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

Model ICBWWD30 with Stainless Steel Drawer Front

Undercounter Installation

51 mm x 51 mm

ANTI-TIP BLOCK

DIMENSION

WILL VARY*

232 mm

OPENING

HEIGHT

606 mm min

OPENING DEPTH

610 mm min

CABINET DEPTH

914 mm

STANDARD

FLOOR TO

COUNTER

HEIGHT

ALLOW FOR

16 mm

OVERLAP OF

DRAWER FACE

ON ALL SIDES

838 mm

RECOMMENDED CABINET WIDTH

762 mm min

102 mm

727 mm

127 mm

OPENING WIDTH

127 mm min

BOTTOM

OF OPENING

TO FLOOR

*Allow enough room for placement of anti-tip block and drawer face overlap.

I N S T A L L A T I O N

O P T I O N S

Installation below 762 mm Built-In Single Oven

Model ICBWWD30 with stainless steel drawer front may be installed above or below a Wolf 762 mm single or double oven, or below an electric or gas cooktop, provided the warming drawer is fully enclosed, top and bottom, with a minimum base support of

91 kg. Refer to the built-in oven and cooktop sections for additional specifications.

It may also be installed next to or above another Model

ICBWWD30.

Model ICBWWD30 with stainless steel drawer front may be installed in combination with a 762 mm single oven.

Refer to the installation instructions provided with the stainless steel drawer front for detailed specifications. These instructions can also be found on our website, wolfappliance.com.

Dimensions will vary according to the specific installation.

610 mm min

CABINET DEPTH

610 mm min

22 mm

PLATFORM

232 mm

OPENING

HEIGHT

606 mm min

OPENING DEPTH

PLATFORM APPLICATION

691 mm

22 mm

610 mm min

CABINET DEPTH

610 mm min

51 mm x 51 mm

ANTI-TIP BLOCK

232 mm

OPENING

HEIGHT

606 mm min

OPENING DEPTH

ANTI-TIP BLOCK APPLICATION

691 mm

60 mm ALLOW FOR

16 mm

OVERLAP OF

DRAWER FACE

ON ALL SIDES

838 mm

RECOMMENDED CABINET WIDTH

762 mm min

724 mm

762 mm OVEN

ROUGH OPENING

102 mm

127 mm

727 mm

WARMING DRAWER

OPENING WIDTH

NOTE: Refer to the built-in 762 mm single oven specifications for electrical location.

W O L F W A R M I N G D R A W E R S

I N S T A L L A T I O N S P E C I F I C A T I O N S

Model ICBWWD30 with Integrated Drawer Front

Undercounter Installation

Overlay Application

51 mm x 51 mm

ANTI-TIP BLOCK

DIMENSION

WILL VARY*

251 mm

260 mm

OPENING

HEIGHT

610 mm min

OPENING DEPTH

610 mm min

CABINET DEPTH

914 mm

STANDARD

FLOOR TO

COUNTER

HEIGHT

ALLOW FOR

OVERLAP OF

DECORATIVE

DRAWER FACE

ON ALL SIDES**

838 mm

RECOMMENDED CABINET WIDTH

762 mm min

102 mm

127 mm

749 mm

OPENING WIDTH 127 mm min

BOTTOM

OF OPENING

TO FLOOR

*Allow enough room for placement of anti-tip block and drawer face overlap.

**Overlap of decorative drawer face will vary depending on the size of the custom panel.

Flush Inset Application

51 mm x 51 mm

ANTI-TIP BLOCK

DIMENSION

WILL VARY*

251 mm

260 mm

OPENING

HEIGHT

610 mm + THICKNESS

OF DRAWER FACE

FOR OPENING DEPTH

635 mm min

CABINET DEPTH

610 mm min

CABINET DEPTH

914 mm

STANDARD

FLOOR TO

COUNTER

HEIGHT

*Allow enough room for placement of anti-tip block.

Installation below 762 mm Built-In Single Oven

635 mm min

CABINET DEPTH

OVERLAY APPLICATION FLUSH INSET APPLICATION

*Dimension may increase depending on the size of the drawer front panel.

838 mm

MINIMUM CABINET WIDTH

610 mm min 691 mm 610 mm min 691 mm

51 mm x 51 mm

ANTI-TIP BLOCK

51 mm x 51 mm

ANTI-TIP BLOCK

251 mm

260 mm

OPENING

HEIGHT

610 mm min

OPENING DEPTH

251 mm

260 mm

OPENING

HEIGHT

38 mm min*

610 mm + THICKNESS

OF DRAWER FACE

FOR OPENING DEPTH

38 mm min*

102 mm

127 mm

749 mm

OPENING WIDTH

127 mm min

BOTTOM

OF OPENING

TO FLOOR

838 mm

CABINET WIDTH

724 mm

762 mm OVEN

OPENING WIDTH

102 mm

127 mm

749 mm

WARMING DRAWER

OPENING WIDTH

S P E C I F I C A T I O N S

Model ICBWWD30 with

Integrated Drawer Front

Overall Width

Overall Height

Overall Depth

(behind frame)

746 mm

257 mm

597 mm

Interior Capacity 45 L

Min Cabinet Width 838 mm

Min Cabinet Depth

Overlay

Flush Inset

Min Base Support

Opening Width

610 mm

635 mm

91 kg

749 mm

Opening Height

Opening Depth*

260 mm

610 mm

Min Panel Size (W x H)

Overlay 762 mm x 264 mm

Flush Inset 746 mm x 257 mm

Min Panel Thickness 16 mm

Electrical Supply 220-240 V AC, 50/60 Hz

15 or 20 amp circuit

Heating Element

Shipping Weight

850 W

45 kg

*For flush inset application, add thickness of drawer face to opening depth.

Unit dimensions may vary to ± 3 mm.

NOTE: Refer to the built-in 762 mm single oven specifications for electrical location.

I N S T A L L A T I O N

O P T I O N S

Model ICBWWD30 with integrated drawer front may be installed above or below any Wolf built-in oven, or below an electric or gas cooktop, provided the warming drawer is fully enclosed, top and bottom, with a minimum base support of 91 kg. Refer to the cooktop and oven sections for additional specifications. It may also be installed next to or above another Model ICBWWD30.

Model ICBWWD30 with integrated drawer front may be installed in combination with a 762 mm or 914 mm single oven.

Refer to the installation instructions provided for detailed specifications.

These instructions can also be found on our website, wolfappliance.com.

T O P C O N F I G U R A T I O N S

Dual Fuel Ranges

IDF364C IDF486C

IDF364G

IDF486G

IDF484CG

IDF484F

IDF606CG

IDF604CF

This appliance is certified by

Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org.

W O L F D U A L F U E L R A N G E S

With Wolf‘s dual fuel ranges you have state-ofthe-art cooking expertise in any number of sizes to meet the discriminating consumer’s precise needs. Patented features ensure this range stands out from the rest in performance and also beauty.

Wolf dual fuel ranges come in 914 mm,

1219 mm and 1524 mm widths. Combined with the top configuration options, the different configurations you can choose from are numerous. Model numbers indicate the top configurations: (C) charbroiler, (G) griddle and

(F) French Top. All Wolf dual fuel ranges come in the classic stainless steel finish.

The electric oven(s) feature the Wolf exclusive dual convection system that delivers even temperature and airflow throughout. Its combination of convection fans and heating elements give the user convenience and superior control over ten different cooking modes.

Advanced standard features such as dualstacked sealed burners, dual convection fans, cobalt blue porcelain oven interior, pivoting control panel, along with the Wolf exclusive infrared charbroiler, infrared griddle and French

Top are all yours for the asking. The freedom to customize your dual fuel range will make you and your client look great.

C O O K I N G M O D E S

Bake

Roast

Broil

Convection Bake

Convection Roast

Convection Broil

Convection

Bake Stone*

Dehydrate*

Proof

* Accessory required.

W O L F D U A L F U E L R A N G E S

F E A T U R E S

Natural or LP gas rangetop with dual convection electric oven(s)

457 mm oven on 1219 mm range is single convection

Optional infrared charbroiler, infrared griddle and French Top configurations

Classic stainless steel exterior finish with island trim included

Distinctive red or black control knobs

Platinum bezels surround all knobs—chrome or brass bezels optional

Dual-stacked, sealed surface burners, all with simmer capabilities and automatic reignition at all settings

4.4 kW burners with .3 kW delivered at simmer

2.7 kW burner with .1 kW delivered at simmer and melt feature

Porcelain-coated cast iron continuous top grates

Pivoting hidden touch control panel

Ten cooking modes

Self-cleaning oven(s) with cobalt blue porcelain oven interior

Coaxial temperature-displaying oven selector knob

Proof mode for 457 mm oven on 1219 mm range

Temperature probe

Three removable oven racks, six-level rack guide and full-extension bottom rack

Hidden bake element and recessed broil element

Triple-pane oven door window(s) and dual halogen lighting

Spring/Damper door system on oven door(s)

Adjustable stainless steel legs in front and adjustable rear casters

D U A L F U E L R A N G E F E A T U R E S

Model IDF484CG shown

Infrared griddle

(optional)

Infrared charbroiler

(optional)

Stainless steel island trim

Dual-stacked, sealed burners

Griddle indicator light

Coaxial oven selector knob

Stainless steel exterior finish

Single convection oven— 1219 mm range only

Spring/Damper door system

Adjustable front legs and rear casters

Blue porcelain oven interiors

Continuous cast iron top grates

Pivoting hidden control panel

Control knobs with platinum bezels

Location of rating plate

Coaxial oven selector knob

Dual halogen oven lighting

Spring/Damper door system

Dual convection oven

A C C E S S O R I E S

Dual Fuel Ranges

127 mm and 254 mm classic stainless steel risers

508 mm classic stainless steel riser with shelf

Red or black control knobs— must be ordered with the range

Chrome or brass bezels

One-piece wok grate and single burner grate

Porcelain-cast two-burner

S-grate

Two-piece broiler pan and temperature probe

Additional oven racks

Hardwood cutting board— griddle models only

Bake stone accessory

Dehydration accessory

Front leg extension covers and rear leg caster covers

Accessories are available through your Wolf dealer.

W O L F D U A L F U E L R A N G E S

P L A N N I N G I N F O R M A T I O N

Wolf dual fuel ranges come in 914 mm,

1219 mm and 1524 mm widths. Specifications on the following pages provide overall dimensions, finished rough opening dimensions and installation specifics for each size of dual fuel range. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation.

IMPORTANT NOTE: Caution must be used in planning the proper installation of the Wolf dual fuel range to avoid fires or damage to adjacent cabinetry or kitchen equipment. Please follow the minimum clearances established in the finished rough opening dimensions. Refer to specifications on the following pages for your model.

E L E C T R I C A L | G A S R E Q U I R E M E N T S

Specifications on the following pages provide electrical and gas requirements for each size of dual fuel range.

Locate electrical and gas supply within the shaded area shown in the Installation Specifications illustration for your model.

International (I) models come with a factory installed transformer and require a 220-240 V

AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. The appropriate electrical connection must be provided in accordance with local requirements.

Wolf dual fuel ranges are designed to operate on natural gas at 12.5 mb WC (water column) pressure or LP (propane) gas at 25 mb WC pressure. The minimum line pressure for natural gas is 17.5 mb WC and 27.4 mb WC for LP gas.

The maximum gas supply pressure to the regulator should never exceed 34.9 mb WC; 3.5 kPa.

Wolf recommends the use of a 13 mm I.D.

commercial-type flex hose; this is the minimum size that may be used. All plumbing to the flex hose must be 19 mm minimum I.D. pipe.

IMPORTANT NOTE: A separate external gas shut-off valve must be located near the range in an accessible location.

You must follow all local codes and ordinances when installing your services.

B U R N E R R A T I N G

Dual Fuel Ranges

Surface Burners 4.4 kW with .3 kW delivered at simmer

(1) 2.7 kW with .1 kW delivered at simmer

Infrared Charbroiler 4.7 kW

Infrared Griddle

Natural Gas

LP Gas

French Top

4.4 kW

3.8 kW

4.4 kW

Refer to the specific model requirements for risers in non-island installations.

W O L F D U A L F U E L R A N G E S

O V E R A L L D I M E N S I O N S

914 mm Dual Fuel Range

911 mm

OVERALL WIDTH

937 mm

OVERALL

HEIGHT TO

COOKING

SURFACE

911 mm

749 mm

OVERALL DEPTH

699 mm

235 mm

616 mm

1194 mm

LEGS AND CASTERS ALLOW

54 mm HEIGHT ADJUSTMENT

1064 mm

WITH

127 mm

RISER

1191 mm

WITH

254 mm

RISER

1445 mm

WITH

508 mm

RISER

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

914 mm Dual Fuel Range

S P E C I F I C A T I O N S

914 mm Dual Fuel Range

Overall Width 911 mm

Overall Height

(to cooking surface) 937 mm

Overall Depth

Overall Oven

Interior Capacity

749 mm

153 L

Overall Interior Dim 762 mm x 419 mm

(W x H x D) x 483 mm

Usable Interior Dim 673 mm x 419 mm

(W x H x D) x 416 mm

Opening Width

Electrical Supply

914 mm

220-240 V AC, 50/60 Hz

30 amp dedicated circuit

Electrical Rating

Total Amps

Shipping Weight

5.2 kW at 240 V

21.7

202–213 kg

VENTILATION HOOD

914 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

152 mm min 1118 mm min

COMBUSTIBLE

FOR CHARBROILER

MATERIALS

(BOTH SIDES)

762 mm min

914 mm max

TO BOTTOM OF

VENTILATION HOOD

914 mm

FINISHED ROUGH OPENING WIDTH

216 mm

381 mm

LOCATION

OF GAS

SUPPLY

LOCATION OF GAS AND

ELECTRICAL EXTENDS 76 mm

ON FLOOR FROM BACK WALL

483 mm

LOCATION OF

ELECTRICAL

83 mm

457 mm min

TO COUNTERTOP

914 mm

937 mm

COOKING

SURFACE

330 mm max

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGE TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

M O D E L O P T I O N S

914 mm Dual Fuel Range

Four Surface Burners

Charbroiler IDF364C

Griddle IDF364G

Natural gas models listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: A minimum 254 mm riser is required when installing a

914 mm dual fuel range with a charbroiler or griddle against a combustible surface.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

W O L F D U A L F U E L R A N G E S

O V E R A L L D I M E N S I O N S

1219 mm Dual Fuel Range

S P E C I F I C A T I O N S

1219 mm Dual Fuel Range

Overall Width 1216 mm

Overall Height

(to cooking surface) 937 mm

Overall Depth 749 mm

Large Oven —

Overall Interior Cap 127 L

Overall Interior Dim 635 mm x 419 mm

(W x H x D) x 483 mm

Usable Interior Dim 546 mm x 419 mm

(W x H x D) x 416 mm

Small Oven —

Overall Interior Cap 71 L

Overall Interior Dim 356 mm x 419 mm

(W x H x D) x 483 mm

Usable Interior Dim 295 mm x 419 mm

(W x H x D) x 416 mm

Opening Width

Electrical Supply

Electrical Rating

Total Amps

Shipping Weight

1216 mm

OVERALL WIDTH

1219 mm

220-240 V AC, 50/60 Hz

50 amp dedicated circuit

10.2 kW at 240 V

42.5

302–340 kg

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

1219 mm Dual Fuel Range

937 mm

OVERALL

HEIGHT TO

COOKING

SURFACE

911 mm

749 mm

OVERALL DEPTH

699 mm

235 mm

616 mm

1194 mm

LEGS AND CASTERS ALLOW

54 mm HEIGHT ADJUSTMENT

1064 mm

WITH

127 mm

RISER

1191 mm

WITH

254 mm

RISER

1445 mm

WITH

508 mm

RISER

M O D E L O P T I O N S

1219 mm Dual Fuel Range

Six Surface Burners

Charbroiler IDF486C

Griddle IDF486G

Four Surface Burners

Charbroiler and

Griddle

French Top

IDF484CG

IDF484F

Natural gas models listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: A minimum 254 mm riser is required for all 1219 mm dual fuel range models installed against a combustible surface.

VENTILATION HOOD

914 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

152 mm min

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

1118 mm min

FOR CHARBROILER

762 mm min

914 mm max

TO BOTTOM OF

VENTILATION HOOD

1219 mm

FINISHED ROUGH OPENING WIDTH

254 mm

LOCATION

OF GAS

SUPPLY

83 mm

610 mm

LOCATION OF GAS AND

ELECTRICAL EXTENDS 76 mm

ON FLOOR FROM BACK WALL

330 mm

LOCATION OF

ELECTRICAL

457 mm min

TO COUNTERTOP

914 mm

937 mm

COOKING

SURFACE

330 mm max

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGE TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

W O L F D U A L F U E L R A N G E S

O V E R A L L D I M E N S I O N S

1524 mm Dual Fuel Range

1527 mm

OVERALL WIDTH

937 mm

OVERALL

HEIGHT TO

COOKING

SURFACE

911 mm

749 mm

OVERALL DEPTH

699 mm

S P E C I F I C A T I O N S

1524 mm Dual Fuel Range

616 mm

235 mm

1194 mm

LEGS AND CASTERS ALLOW

54 mm HEIGHT ADJUSTMENT

1064 mm

WITH

127 mm

RISER

1191 mm

WITH

254 mm

RISER

1445 mm

WITH

508 mm

RISER

Overall Width 1527 mm

Overall Height

(to cooking surface) 937 mm

Overall Depth 749 mm

Overall Oven Interior

Capacity (per oven) 127 L

Overall Interior Dim 635 mm x 419 mm

(W x H x D) x 483 mm each

Usable Interior Dim 546 mm x 419 mm

(W x H x D) x 416 mm each

Opening Width

Electrical Supply

1530 mm

220-240 V AC, 50/60 Hz

50 amp dedicated circuit

Electrical Rating

Total Amps

Shipping Weight

10.2 kW at 240 V

42.5

397–431 kg

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

1524 mm Dual Fuel Range

VENTILATION HOOD

152 mm min

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

914 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

1118 mm min

FOR CHARBROILER

1530 mm

FINISHED ROUGH OPENING WIDTH

762 mm min

914 mm max

TO BOTTOM OF

VENTILATION HOOD

254 mm

LOCATION

OF GAS

SUPPLY

83 mm

787 mm

LOCATION OF GAS AND

ELECTRICAL EXTENDS 76 mm

ON FLOOR FROM BACK WALL

330 mm

LOCATION OF

ELECTRICAL

457 mm min

TO COUNTERTOP

914 mm

937 mm

COOKING

SURFACE

330 mm max

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGE TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

M O D E L O P T I O N S

1524 mm Dual Fuel Range

Six Surface Burners

French Top IDF606F

Charbroiler and

Griddle IDF606CG

Natural gas models listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: A minimum 254 mm riser is required for all 1524 mm dual fuel range models installed against a combustible surface.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

T O P C O N F I G U R A T I O N S

Sealed Burner Rangetops

ICBSRT304 ICBSRT364C ICBSRT486C

ICBSRT364G ICBSRT486G

ICBSRT484CG

ICBSRT484F

This appliance is certified by

Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org.

W O L F S E A L E D B U R N E R R A N G E T O P S

There’s a good reason why professional chefs choose gas cooking: control. The patented, dual-stacked sealed gas burners of our new sealed burner rangetop take control to a new level. Two levels, really. The upper-tier burner delivers maximum heat transfer at higher settings; the lower-tier continuous flame ably handles the subtleties of simmering and melting.

Patented features along with the Wolf exclusive infrared charbroiler, infrared griddle and French

Top ensure this rangetop stands out from the rest in performance as well as beauty.

Wolf sealed burner rangetops come in 762 mm,

914 mm and 1219 mm widths and are available in natural or LP gas, with your choice of several top configurations. Model numbers indicate the top configurations; (C) charbroiler, (G) griddle and (F) French Top. The model number followed by (-LP) denotes an LP gas model. All Wolf sealed burner rangetops come in the classic stainless steel finish.

W O L F S E A L E D B U R N E R R A N G E T O P S

F E A T U R E S

Natural or LP gas models

Classic stainless steel exterior finish with island trim

Optional infrared charbroiler, infrared griddle and

French Top configurations

Distinctive red control knobs—optional black knobs available at no cost

Platinum bezels surround all knobs—chrome or brass bezels optional

Dual-stacked, sealed surface burners, all with simmer capabilities and electronic reignition at all settings

5.0 kW burners with .3 kW delivered at simmer

3.2 kW burner with .1 kW delivered at simmer and melt feature

Porcelain-coated cast iron continuous top grates

S E A L E D B U R N E R R A N G E T O P F E A T U R E S

Model ICBSRT484CG shown

Infrared griddle

(optional)

Infrared charbroiler

(optional)

Low-profile island trim

Continuous, cast iron top grates

Dual-stacked, sealed burners

Stainless steel exterior finish

Griddle indicator light

Control knobs with platinum bezels

Location of rating plate

A C C E S S O R I E S

Sealed Burner Rangetops

127 mm and 254 mm classic stainless steel risers

508 mm classic stainless steel riser with shelf

Black control knobs—one set available at no cost

Chrome or brass bezels

One-piece wok grate and single burner grate

Porcelain-cast two-burner

S-grate

SRT/Downdraft trim kit—Model

ICBSRT304 only

Hardwood cutting board—griddle models only

Accessories are available through your Wolf dealer.

W O L F S E A L E D B U R N E R R A N G E T O P S

P L A N N I N G I N F O R M A T I O N

Wolf sealed burner rangetops come in 762 mm,

914 mm and 1219 mm widths. Specifications on the following pages provide overall dimensions, finished rough opening dimensions and installation specifics for each size of sealed burner rangetop. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation.

IMPORTANT NOTE: Caution must be used in planning the proper installation of the Wolf sealed burner rangetop to avoid fires or damage to adjacent cabinetry or kitchen equipment.

Please follow the minimum clearances established in the finished rough opening dimensions.

Refer to specifications on the following pages for your model.

A downdraft can be used with Model

ICBSRT304. An accessory trim kit is necessary for this installation. Contact your Wolf dealer for details.

E L E C T R I C A L | G A S R E Q U I R E M E N T S

Specifications on the following pages provide electrical and gas requirements for each size of sealed burner rangetop.

The Wolf sealed burner rangetop is CB approved and manufactured for a 220-240 V AC, 50/60 Hz electrical supply to operate the electronic ignition system. The service should have its own 15 amp circuit breaker.

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

Wolf sealed burner rangetops are designed to operate without a regulator on natural gas at

17-25 mb pressure or LP (propane) gas at 25-45 mb.

If local codes permit, a certified, .9 m long,

13 mm or 19 mm I.D. flexible metal appliance connector is recommended for connecting the rangetop to the gas supply line.

The platform for the rangetop must be 19 mm thick and include a cut-out at the right rear for gas supply and electrical connections.

Locate electrical and gas supply within the shaded area shown in the Installation Specifications illustration for your model.

You must follow all local codes and ordinances when installing your services.

B U R N E R R A T I N G

Sealed Burner Rangetops

Surface Burners 5.0 kW with .3 kW delivered at simmer

(1) 3.2 kW with .1 kW delivered at simmer

Infrared Charbroiler

Natural Gas

LP Gas

Infrared Griddle

Natural Gas

LP Gas

French Top

6.2 kW

5.4 kW

5.5 kW

5.0 kW

Refer to the specific model requirements for risers in non-island installations.

W O L F S E A L E D B U R N E R R A N G E T O P S

O V E R A L L D I M E N S I O N S

762 mm Sealed Burner Rangetop

759 mm

OVERALL WIDTH

COOKING

SURFACE

216 mm

OVERALL

HEIGHT

191 mm

724 mm

OVERALL DEPTH

616 mm

235 mm

699 mm

WITH 508 mm

RISER

318 mm

WITH

127 mm

RISER

445 mm

WITH

254 mm

RISER

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

762 mm Sealed Burner Rangetop

S P E C I F I C A T I O N S

762 mm Sealed Burner Rangetop

Overall Width 759 mm

Overall Height

(to cooking surface) 216 mm

Overall Depth

Opening Width

Opening Height 191 mm

(platform to countertop)

Opening Depth 1219 mm

Electrical Supply

724 mm

762 mm

Shipping Weight

220-240 V AC

50/60 Hz, 15 amp dedicated circuit

73 kg

VENTILATION

HOOD

152 mm min

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

762 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

762 mm min

TO 914 mm max

TO BOTTOM OF

VENTILATION HOOD

762 mm

OPENING WIDTH

19 mm

PLATFORM

LOCATION OF GAS AND

ELECTRICAL SUPPLY CUT-OUT

WITHIN SHADED AREA

THROUGH BOTTOM OF

PLATFORM

406 mm

TOP VIEW

OF PLATFORM

102 mm

BACK

WALL

E G

406 mm

330 mm max

457 mm min

TO COUNTERTOP

COOKING

SURFACE

216 mm

914 mm

191 mm

19 mm

PLATFORM

610 mm

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGETOP TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

M O D E L O P T I O N S

762 mm Sealed Burner

Rangetops

Four Surface

Burners ICBSRT304

Natural gas model listed; for LP gas add (-LP) to the model number.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

W O L F S E A L E D B U R N E R R A N G E T O P S

S P E C I F I C A T I O N S

914 mm Sealed Burner Rangetop

Overall Width 911 mm

Overall Height

(to cooking surface) 216 mm

Overall Depth

Opening Width

Opening Height 191 mm

(platform to countertop)

Opening Depth 1219 mm

Electrical Supply

724 mm

914 mm

Shipping Weight

220-240 V AC

50/60 Hz, 15 amp dedicated circuit

86–100 kg

O V E R A L L D I M E N S I O N S

914 mm Sealed Burner Rangetop

911 mm

OVERALL WIDTH

COOKING

SURFACE

216 mm

OVERALL

HEIGHT

191 mm

724 mm

OVERALL DEPTH

616 mm

235 mm

699 mm

WITH 508 mm

RISER

318 mm

WITH

127 mm

RISER

445 mm

WITH

254 mm

RISER

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

914 mm Sealed Burner Rangetop

M O D E L O P T I O N S

914 mm Sealed Burner

Rangetops

Four Surface Burners

Charbroiler ICBSRT364C

Griddle ICBSRT364G

Natural gas models listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: A minimum

254 mm riser is required for charbroiler (C) or griddle (G) models installed against a combustible surface.

VENTILATION HOOD

914 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

152 mm min

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

1118 mm min

FOR CHARBROILER

762 mm min TO

914 mm min

TO BOTTOM OF

VENTILATION HOOD

914 mm

FINISHED ROUGH OPENING WIDTH

19 mm

PLATFORM

LOCATION OF GAS AND

ELECTRICAL SUPPLY CUT-OUT

WITHIN SHADED AREA

THROUGH BOTTOM OF

PLATFORM

406 mm

TOP VIEW

OF PLATFORM

102 mm

BACK

WALL

E G

406 mm

457 mm min

TO COUNTERTOP

COOKING

SURFACE

216 mm 191 mm

19 mm

PLATFORM

610 mm

914 mm

330 mm max

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGETOP TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

W O L F S E A L E D B U R N E R R A N G E T O P S

O V E R A L L D I M E N S I O N S

1219 mm Sealed Burner Rangetop

1216 mm

OVERALL WIDTH

COOKING

SURFACE

216 mm

OVERALL

HEIGHT

191 mm

724 mm

OVERALL DEPTH

616 mm

235 mm

699 mm

WITH 508 mm

RISER

318 mm

WITH

127 mm

RISER

445 mm

WITH

254 mm

RISER

S P E C I F I C A T I O N S

1219 mm Sealed Burner Rangetop

Overall Width 1216 mm

Overall Height

(to cooking surface) 216 mm

Overall Depth

Opening Width

Opening Height 191 mm

(platform to countertop)

Opening Depth 1219 mm

Electrical Supply

724 mm

1219 mm

Shipping Weight

220-240 V AC

50/60 Hz, 15 amp dedicated circuit

109–127 kg

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

1219 mm Sealed Burner Rangetop

VENTILATION HOOD

152 mm min

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

914 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

1118 mm min

FOR CHARBROILER

762 mm min

914 mm max

TO BOTTOM OF

VENTILATION HOOD

1219 mm

FINISHED ROUGH OPENING WIDTH

19 mm

PLATFORM

LOCATION OF GAS AND

ELECTRICAL SUPPLY CUT-OUT

WITHIN SHADED AREA

THROUGH BOTTOM OF

PLATFORM

406 mm

TOP VIEW

OF PLATFORM

102 mm

BACK

WALL

E G

406 mm

330 mm max

457 mm min

TO COUNTERTOP

COOKING

SURFACE

216 mm

914 mm

191 mm

19 mm

PLATFORM

610 mm

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGETOP TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

M O D E L O P T I O N S

1219 mm Sealed Burner

Rangetops

Six Surface Burners

Charbroiler ICBSRT486C

Griddle ICBSRT486G

Four Surface Burners

Charbroiler and Griddle ICBSRT484CG

French Top ICBSRT484F

Natural gas models listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: A minimum

254 mm riser is required for charbroiler (C) or griddle (G) models installed against a combustible surface.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

T O P C O N F I G U R A T I O N S

Gas Ranges

IR304 IR364C IR486C

IR364G IR486G

IR484CG

This appliance is certified by

Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org.

IR606CG

W O L F G A S R A N G E S

If it looks as if it could be in a restaurant kitchen, well, that’s natural. That’s precisely where Wolf has spent the past seven decades, perfecting the form, function and sheer durability of our stainless steel gas ranges.

Wolf gas ranges come in 762 mm, 914 mm,

1219 mm and 1524 mm widths, and combined with the top configuration options, the different configurations you can choose from are numerous. Model numbers indicate the top configurations: (C) charbroiler, (G) griddle and (F) French Top.

Advanced standard features such as an infrared oven broiler, convection baking and dual burners along with the Wolf exclusive infrared charbroiler, infrared griddle and French

Top are all yours for the asking. The freedom to customize your gas range will make you and your client look great.

All Wolf gas ranges come in the classic stainless steel finish and are shipped with the distinctive red control knobs. Contact your

Wolf dealer for optional black knobs available at no cost.

W O L F G A S R A N G E S

F E A T U R E S

Natural or LP gas models

Fits standard 610 mm deep cabinets with zero clearance for easy installation

Optional infrared charbroiler, infrared griddle and

French Top configurations

Classic stainless steel exterior finish

Dual brass burners with automatic reignition at all settings, .1 kW simmer to 4.7 kW high

Porcelain-coated cast iron top grates

Large red control knobs with four position settings and chrome bezels—optional black knobs available

Large-capacity convection oven(s) with infrared broiler, porcelain interior, three adjustable racks, lights and door window

457 mm oven with porcelain interior, two adjustable racks, lights and door window on

1219 mm range

Spring/Damper door system on oven door(s)

Stainless steel drip tray on ball bearing slides

Adjustable 76 mm stainless steel legs in front and rear casters

Full side panels and skirt

G A S R A N G E F E A T U R E S

Model IR484CG shown with 127 mm riser

Porcelain-coated, cast iron top grates

Infrared charbroiler

(optional)

Infrared griddle

(optional)

Large red control knobs

Location of rating plate

Oven light switch

Stainless steel exterior finish

Full side panels and skirt

Spring/Damper door system

457 mm oven—

1219 mm range only

Large capacity convection oven

127 mm riser

(optional)

Dual brass burners

Burner drip pan

Oven light switch

Pull-out drip tray

Convection fan switch

Oven indicator light

Griddle indicator light

A C C E S S O R I E S

Gas Ranges

127 mm and 254 mm classic stainless steel risers

508 mm classic stainless steel riser with shelf

Classic stainless steel island trim

Black control knobs—available at no cost

Porcelain-coated, cast iron wok grate

Porcelain-coated, cast iron two-burner S-grate

Hardwood cutting board—griddle models only

Additional oven racks

Accessories are available through your Wolf dealer.

W O L F G A S R A N G E S

P L A N N I N G I N F O R M A T I O N

Wolf gas ranges come in 762 mm, 914 mm,

1219 mm and 1524 mm widths. Specifications on the following pages provide overall dimensions, finished rough opening dimensions and installation specifics for each size of gas range.

We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation.

IMPORTANT NOTE: Caution must be used in planning the proper installation of the Wolf gas range to avoid fires or damage to adjacent cabinetry or kitchen equipment. Please follow the minimum clearances established in the finished rough opening dimensions. Refer to specifications on the following pages for your model.

E L E C T R I C A L | G A S R E Q U I R E M E N T S

International (I) models come with a factory installed transformer and require a 220-240

V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. The appropriate electrical connection must be provided in accordance with local requirements. The service should have its own 15 amp circuit breaker.

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

Locate electrical and gas supply within the shaded area shown in the Installation Specifications illustration for your model.

Wolf gas ranges are designed to operate on natural gas at 12.5 mb WC (water column) pressure or LP (propane) gas at 25 mb WC pressure. The minimum line pressure for natural gas is 17.5 mb WC and 27.4 mb WC for LP gas.

The maximum gas supply pressure to the regulator should never exceed 34.9 mb WC; 3.5 kPa.

Wolf recommends the use of a 13 mm I.D.

commercial-type flex hose; this is the minimum size that may be used. All plumbing to the flex hose must be 19 mm minimum I.D. pipe.

IMPORTANT NOTE: A separate external gas shut-off valve must be located near the range in an accessible location.

You must follow all local codes and ordinances when installing your services.

B U R N E R R A T I N G

Gas Ranges

Surface Burners 4.7 kW with .1 kW delivered at simmer

Infrared Charbroiler 4.7 kW

Infrared Griddle 5.3 kW

French Top 4.4 kW

Oven Burner (Bake) 8.8 kW

Infrared Oven Broiler 5.3 kW

Refer to the specific model requirements for risers in non-island installations.

W O L F G A S R A N G E S

O V E R A L L D I M E N S I O N S

762 mm Gas Range

721 mm

OVERALL DEPTH

692 mm

762 mm

OVERALL WIDTH

235 mm

940 mm

OVERALL

HEIGHT TO

COOKING

SURFACE

914 mm

622 mm

64 mm

641 mm

1102 mm

LEGS AND CASTERS ALLOW

25 mm HEIGHT ADJUSTMENT

1060 mm

WITH

127 mm

RISER

1187 mm

WITH

254 mm

RISER

1441 mm

WITH

508 mm

RISER

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

762 mm Gas Range

S P E C I F I C A T I O N S

762 mm Gas Range

Overall Width 762 mm

Overall Height

(to cooking surface) 940 mm

Overall Depth

Overall Oven

Interior Capacity

721 mm

125 L

Overall Interior Dim 610 mm x 473 mm

(W x H x D) x 432 mm

Usable Interior Dim 610 mm x 419 mm

(W x H x D) x 432 mm

Opening Width

Electrical Supply

768 mm

Power Cord

Shipping Weight

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

1.8 m 3-prong

147 kg

VENTILATION

HOOD

152 mm min

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

762 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

762 mm

914 mm

COUNTERTOP

TO BOTTOM OF

VENTILATION HOOD

457 mm min

TO COUNTERTOP

330 mm max

768 mm

FINISHED ROUGH

OPENING WIDTH

254 mm

203 mm

305 mm

51 mm

140 mm

305 mm

127 mm

ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK

OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP –

0 mm TO NON-COMBUSTIBLE MATERIALS

914 mm

940 mm

COOKING

SURFACE

LOCATION OF GAS SUPPLY EXTENDS

76 mm ON FLOOR FROM BACK WALL

76 mm

M O D E L O P T I O N S

762 mm Gas Range

Four Surface

Burners IR304

Natural gas model listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: A minimum 127 mm riser is required when installing a

762 mm gas range against a combustible surface.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

W O L F G A S R A N G E S

S P E C I F I C A T I O N S

914 mm Gas Range

Overall Width 914 mm

Overall Height

(to cooking surface) 940 mm

Overall Depth

Overall Oven

Interior Capacity

721 mm

156 L

Overall Interior Dim 762 mm x 473 mm

(W x H x D) x 432 mm

Usable Interior Dim 762 mm x 419 mm

(W x H x D) x 432 mm

Opening Width

Electrical Supply

921 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

Power Cord

Shipping Weight

1.8 m 3-prong

202–213 kg

O V E R A L L D I M E N S I O N S

914 mm Gas Range

721 mm

OVERALL DEPTH

692 mm

914 mm

OVERALL WIDTH

235 mm

940 mm

OVERALL

HEIGHT TO

COOKING

SURFACE

914 mm

622 mm

64 mm

641 mm

1102 mm

LEGS AND CASTERS ALLOW

25 mm HEIGHT ADJUSTMENT

1060 mm

WITH

127 mm

RISER

1187 mm

WITH

254 mm

RISER

1441 mm

WITH

508 mm

RISER

Unit dimensions may vary to ± 3 mm.

M O D E L O P T I O N S

914 mm Gas Range

Four Surface Burners

Charbroiler IR364C

Griddle IR364G

Natural gas models listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: A minimum 254 mm riser is required when installing a gas range with a charbroiler or griddle against a combustible surface.

I N S T A L L A T I O N S P E C I F I C A T I O N S

914 mm Gas Range

VENTILATION

HOOD

152 mm min

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

762 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

914 mm min

FOR

CHARBROILER

762 mm TO 914 mm

COUNTERTOP

TO BOTTOM OF

VENTILATION HOOD

457 mm min

TO COUNTERTOP

330 mm max

921 mm

FINISHED ROUGH OPENING WIDTH

254 mm

305 mm

203 mm

51 mm

140 mm

305 mm

ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK

OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP –

0 mm TO NON-COMBUSTIBLE MATERIALS

127 mm

914 mm

940 mm

COOKING

SURFACE

LOCATION OF GAS SUPPLY EXTENDS

76 mm ON FLOOR FROM BACK WALL

76 mm

W O L F G A S R A N G E S

O V E R A L L D I M E N S I O N S

1219 mm Gas Range

1219 mm

OVERALL WIDTH

Unit dimensions may vary to ± 3 mm.

721 mm

OVERALL DEPTH

692 mm

235 mm

940 mm

OVERALL

HEIGHT TO

COOKING

SURFACE

914 mm

622 mm

64 mm

641 mm

1102 mm

LEGS AND CASTERS ALLOW

25 mm HEIGHT ADJUSTMENT

1060 mm

WITH

127 mm

RISER

1187 mm

WITH

254 mm

RISER

1441 mm

WITH

508 mm

RISER

S P E C I F I C A T I O N S

1219 mm Gas Range

Overall Width 1219 mm

Overall Height

(to cooking surface) 940 mm

Overall Depth 721 mm

Large Oven —

Overall Interior Cap 125 L

Overall Interior Dim 610 mm x 473 mm

(W x H x D) x 432 mm

Usable Interior Dim 610 mm x 419 mm

(W x H x D) x 432 mm

Small Oven —

Overall Interior Cap 71 L

Overall Interior Dim 343 mm x 473 mm

(W x H x D) x 432 mm

Usable Interior Dim 343 mm x 419 mm

(W x H x D) x 432 mm

Opening Width

Electrical Supply

Power Cord

Shipping Weight

1226 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

1.8 m 3-prong

295–340 kg

I N S T A L L A T I O N S P E C I F I C A T I O N S

1219 mm Gas Range

VENTILATION HOOD

152 mm min

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

762 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

914 mm min

FOR CHARBROILER

762 mm TO 914 mm

COUNTERTOP TO

BOTTOM OF

VENTILATION HOOD

457 mm min

TO COUNTERTOP

330 mm max

1226 mm

FINISHED ROUGH OPENING WIDTH

660 mm

305 mm

203 mm

140 mm

305 mm

ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK

OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP –

0 mm TO NON-COMBUSTIBLE MATERIALS

51 mm

914 mm

940 mm

COOKING

SURFACE

127 mm

LOCATION OF GAS SUPPLY EXTENDS

76 mm ON FLOOR FROM BACK WALL

76 mm

M O D E L O P T I O N S

1219 mm Gas Range

Six Surface Burners

Charbroiler IR486C

Griddle IR486G

Four Surface Burners

Charbroiler and

Griddle IR484CG

Natural gas models listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: A minimum 254 mm riser is required when installing a gas range with a charbroiler or griddle against a combustible surface.

W O L F G A S R A N G E S

S P E C I F I C A T I O N S

1524 mm Gas Range

Overall Width 1524 mm

Overall Height

(to cooking surface) 940 mm

Overall Depth 721 mm

Overall Oven Interior

Capacity (per oven) 125 L

Overall Interior Dim 610 mm x 473 mm

(W x H x D) x 432 mm each

Usable Interior Dim 610 mm x 419 mm

(W x H x D) x 432 mm each

Opening Width

Electrical Supply

1530 mm

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

Power Cord

Shipping Weight

1.8 m 3-prong

397–431 kg

O V E R A L L D I M E N S I O N S

1524 mm Gas Range

1524 mm

OVERALL WIDTH

721 mm

OVERALL DEPTH

692 mm

235 mm

940 mm

OVERALL

HEIGHT TO

COOKING

SURFACE

914 mm

622 mm

64 mm

641 mm

1102 mm

LEGS AND CASTERS ALLOW

25 mm HEIGHT ADJUSTMENT

1060 mm

WITH

127 mm

RISER

1187 mm

WITH

254 mm

RISER

1441 mm

WITH

508 mm

RISER

Unit dimensions may vary to ± 3 mm.

M O D E L O P T I O N S

1524 mm Gas Range

Four Surface Burners

Charbroiler and

Griddle IR606CG

Natural gas models listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: A minimum 254 mm riser is required when installing a gas range with a charbroiler or griddle against a combustible surface.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

I N S T A L L A T I O N S P E C I F I C A T I O N S

1524 mm Gas Range

VENTILATION HOOD

152 mm min

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

1118 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

762 mm TO 914 mm

COUNTERTOP

TO BOTTOM OF

VENTILATION HOOD

457 mm min

TO COUNTERTOP

330 mm max

1530 mm

FINISHED ROUGH OPENING WIDTH

254 mm

203 mm

140 mm

305 mm

ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK

OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP –

0 mm TO NON-COMBUSTIBLE MATERIALS

51 mm

914 mm

940 mm

COOKING

SURFACE

127 mm

LOCATION OF GAS SUPPLY EXTENDS

76 mm ON FLOOR FROM BACK WALL

76 mm

W O L F G A S R A N G E T O P S

If you want to offer a more professional look to your client’s kitchen and still use a cooktop, look to the rangetops from Wolf. They offer you that commercial look but give you flexibility to use the ovens in other locations in the kitchen. In fact, the Wolf framed ovens would be a beautiful complement to these cooking instruments.

Wolf gas rangetops come in 914 mm and 1219 mm widths and are available in natural or LP gas, with your choice of several top configurations. Model numbers indicate the top configurations: (C) charbroiler, (G) griddle and (F) French

Top.

Choose from four or six dual burners or consider the Wolf exclusive infrared charbroiler, infrared griddle or French Top for the ultimate in restaurant cooking in the home.

The dual burners can produce 4.7 kW for professional cooking heat or as little as .1 kW for those delicate sauces.

All Wolf gas rangetops come in the classic stainless steel finish and are shipped with the distinctive red control knobs. Contact your Wolf dealer for optional black knobs available at no cost.

G A S R A N G E T O P F E A T U R E S

Model IRT484CG shown with island trim

Infrared charbroiler

(optional)

Infrared griddle

(optional)

Low-profile island trim

Porcelain-coated cast iron top grates

Dual brass burners

T O P C O N F I G U R A T I O N S

Gas Rangetops

IRT364C IRT486C

Location of rating plate

Pull-out drip tray Large red control knobs

A C C E S S O R I E S

Gas Rangetops

267 mm classic stainless steel riser

Classic stainless steel island trim

Black control knobs—available at no cost

Porcelain-coated, cast iron wok grate

Porcelain-coated, cast iron two-burner S-grate

Hardwood cutting board—griddle models only

Accessories are available through your Wolf dealer.

Griddle indicator light

Stainless steel exterior finish

This appliance is certified by

Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org.

IRT364G IRT486G

IRT484CG

IRT484F

W O L F G A S R A N G E T O P S

F E A T U R E S

Natural or LP gas models

Fits standard 610 mm deep cabinets with zero clearance for easy installation

Optional infrared charbroiler, infrared griddle and French Top configurations

Classic stainless steel exterior finish

Dual brass burners with automatic reignition at all settings, .1 kW simmer to 4.7 kW high

Porcelain-coated cast iron top grates

Large red control knobs with four position settings and chrome bezels—optional black knobs available

Stainless steel drip tray on ball bearing slides

P L A N N I N G I N F O R M A T I O N

Wolf gas rangetops come in 914 mm and 1219 mm widths. Specifications on the following pages provide overall dimensions, finished rough opening dimensions and installation specifics for each size of gas rangetop. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation.

IMPORTANT NOTE: Caution must be used in planning the proper installation of the Wolf gas rangetop to avoid fires or damage to adjacent cabinetry or kitchen equipment. Follow the minimum clearances established in the finished rough opening dimensions. Refer to specifications on the following pages for your model.

E L E C T R I C A L | G A S R E Q U I R E M E N T S

Specifications on the following pages provide electrical and gas requirements for each size of gas rangetop.

International (I) models come with a factory installed transformer and require a 220-240

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

Wolf gas rangetops are designed to operate on natural gas at 12.5 mb WC (water column) pressure or LP (propane) gas at 25 mb WC pressure. The minimum line pressure for natural gas is 17.5 mb WC and 27.4 mb WC for LP gas.

The maximum gas supply pressure to the regulator should never exceed 34.9 mb WC; 3.5 kPa.

Wolf recommends the use of a 13 mm I.D.

commercial-type flex hose; this is the minimum size that may be used. All plumbing to the flex hose must be 19 mm minimum I.D. pipe.

IMPORTANT NOTE: A separate external gas shut-off valve must be located near the range in an accessible location.

The platform for the rangetop must be 19 mm thick and include a cut-out at the right rear for gas supply and electrical connections.

Locate electrical and gas supply within the shaded area shown in the Installation Specifications illustration for your model.

You must follow all local codes and ordinances when installing your services.

B U R N E R R A T I N G

Gas Rangetops

Surface Burners 4.7 kW with .1 kW delivered at simmer

Infrared Charbroiler 4.7 kW

Infrared Griddle

French Top

5.3 kW

4.4 kW

Refer to the specific model requirements for risers in non-island installations.

W O L F G A S R A N G E T O P S

O V E R A L L D I M E N S I O N S

914 mm Gas Rangetop

914 mm

OVERALL WIDTH

COOKING

SURFACE

267 mm

OVERALL

HEIGHT

241 mm

692 mm

OVERALL DEPTH

TO KNOBS

70 mm

51 mm

508 mm

WITH

267 mm

RISER

610 mm

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

914 mm Gas Rangetop

VENTILATION HOOD

762 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

152 mm min 914 mm min

COMBUSTIBLE

FOR CHARBROILER

MATERIALS

(BOTH SIDES)

762 mm min

TO 914 mm max

COUNTERTOP

TO BOTTOM OF

VENTILATION HOOD

921 mm

FINISHED ROUGH OPENING WIDTH

19 mm PLATFORM

TOP VIEW

OF PLATFORM

13 mm

BACK WALL

76 mm E G

203 mm

356 mm

LOCATION OF

GAS AND ELECTRICAL

SUPPLY CUT-OUT

WITHIN SHADED AREA

THROUGH BOTTOM OF

PLATFORM

457 mm min

TO COUNTERTOP

914 mm

241 mm

OPENING

HEIGHT

70 mm

330 mm max

19 mm

PLATFORM

610 mm

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGETOP TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

S P E C I F I C A T I O N S

914 mm Gas Rangetop

Overall Width 914 mm

Overall Height

(to cooking surface) 267 mm

Overall Depth

Opening Width

692 mm

921 mm

Opening Height 241 mm

(platform to countertop)

Electrical Supply 220-240 V AC, 50/60 Hz

15 amp dedicated circuit

Power Cord

Shipping Weight

1.8 m 3-prong

86–100 kg

M O D E L O P T I O N S

914 mm Gas Rangetop

Four Surface Burners

Charbroiler IRT364C

Griddle IRT364G

Natural gas models listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: In nonisland applications, a riser is required when installing a

914 mm gas rangetop against a combustible surface.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

W O L F G A S R A N G E T O P S

O V E R A L L D I M E N S I O N S

1219 mm Gas Rangetop

S P E C I F I C A T I O N S

1219 mm Gas Rangetop

Overall Width 1219 mm

Overall Height

(to cooking surface) 267 mm

Overall Depth

Opening Width

692 mm

1226 mm

Opening Height 241 mm

(platform to countertop)

Electrical Supply 220-240 V AC, 50/60 Hz

15 amp dedicated circuit

Power Cord

Shipping Weight

1.8 m 3-prong

100–127 kg

1219 mm

OVERALL WIDTH

Unit dimensions may vary to ± 3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S

1219 mm Gas Rangetop

M O D E L O P T I O N S

1219 mm Gas Rangetop

Six Surface Burners

Charbroiler IRT486C

Griddle IRT486G

Four Surface Burners

Charbroiler and

Griddle IRT484CG

French Top IRT484F

Natural gas models listed; for LP gas add (-LP) to the model number.

IMPORTANT NOTE: In nonisland applications, a riser is required when installing a

1219 mm gas rangetop against a combustible surface.

VENTILATION HOOD

COOKING

SURFACE

267 mm

OVERALL

HEIGHT

241 mm

692 mm

OVERALL DEPTH

TO KNOBS

70 mm

51 mm

508 mm

WITH

267 mm

RISER

610 mm

762 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

152 mm min 914 mm min

COMBUSTIBLE

FOR CHARBROILER

MATERIALS

(BOTH SIDES)

762 mm min

TO 914 mm max

COUNTERTOP

TO BOTTOM OF

VENTILATION HOOD

1226 mm

FINISHED ROUGH OPENING WIDTH

19 mm PLATFORM

TOP VIEW

OF PLATFORM

76 mm 13 mm

BACK WALL

E G

406 mm

406 mm 356 mm

LOCATION OF GAS AND

ELECTRICAL SUPPLY CUT-OUT

WITHIN SHADED AREA

THROUGH BOTTOM OF

PLATFORM

457 mm min

TO COUNTERTOP

914 mm

241 mm

OPENING

HEIGHT

70 mm

330 mm max

19 mm PLATFORM

610 mm

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGETOP TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

W O L F C O O K T O P V E N T I L A T I O N

W O L F E S E R I E S C O O K T O P H O O D S

Behind the contemporary lines of the Wolf

E Series cooktop hoods, there's a lot of hardnosed functional thinking. Brilliant halogen lighting illuminates your cooking surface.

Powerful multi-speed blowers whisk away smoke and odors. Wall-mount hoods in three widths and island hood are available in classic stainless steel.

E Series cooktop wall and island hoods are recommended for use with Wolf electric and gas cooktops and integrated modules.

F E A T U R E S

Classic stainless steel finish

Internal and remote blower options

Front-mounted electronic controls with digital indicator

Heavy-duty stainless steel construction

Four-speed blower control

Filter clean indicator lets you know when the filter needs cleaning

Delay-off feature automatically turns unit off

Sealed halogen lighting with three settings

Stainless steel filter cover with dishwasher-safe aluminum mesh filter

Heat sentry feature automatically turns unit on when heat is sensed and automatically adjusts blower speed

Hood can be ducted to the outside or nonducted using a charcoal filter (internal blower

(I) models only)

Transition with back draft damper included

Fits 2.4 m to 2.7 m ceilings

Model ICTEWH30I

Model ICTEWH36I

Model ICTEWH45I

W O L F E S E R I E S C O O K T O P H O O D F E A T U R E S

Model ICTEWH36I shown

Classic stainless steel finish

Transition with backdraft damper

Dishwasher-safe filter

Location of rating plate

Telescopic flue

Halogen lighting Electronic controls with digital indicator

(I) Models include 500

CFM Internal blower

Filter clean indicator

Four-speed blower control

M O D E L O P T I O N S

E Series Cooktop Hoods

Wall Hoods

762 mm Width

914 mm Width

1143 mm Width

Island Hood

ICTEWH30I*

ICTEWH36I

ICTEWH36I*

ICTEWH45I*

ICTEIH42I*

*500 CFM internal blower included.

Model ICTEIH42I

W O L F C O O K T O P V E N T I L A T I O N

P L A N N I N G I N F O R M A T I O N

Wolf E Series cooktop wall hoods are 450 mm deep and come in 762 mm, 914 mm and 1143 mm widths. The island hood is 1067 mm wide by 550 mm deep. (I) models include a 500 CFM internal blower.

IMPORTANT NOTE: E Series cooktop wall and island hoods are recommended for use with

Wolf electric and gas cooktops along with integrated modules, and should be at least as wide as the cooking surface.

Wolf E Series cooktop wall and island hoods come with a telescopic flue that allows you to reach a ceiling height of 2.4 m to 2.7 m with a finished look.

Specifications on the following pages provide overall dimensions, blower and ducting considerations, and installation specifics for cooktop wall and island hoods. We have minimized the information contained in the illustrations, concentrating on the critical information you must plan into your installation.

Installation of the cooktop wall or island hood should be 650 mm to 760 mm from the bottom of the hood to the countertop.

E L E C T R I C A L R E Q U I R E M E N T S

Wolf E Series cooktop wall and island hoods require a separate, grounded 220-240 V AC,

50/60 Hz power supply with a dedicated 15 amp circuit. Placement of the electrical supply is not critical, as long as it is accessible

Locate electrical within the shaded area shown in the Installation Specifications illustration for your model.

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

You must follow all local codes and ordinances when installing your service.

A C C E S S O R I E S

E Series Cooktop Hoods

Internal and remote blower assemblies

Charcoal filters for non-ducted applications (internal blower

(I) models only)

Accessories are available through your Wolf dealer.

W O L F C O O K T O P V E N T I L A T I O N

O V E R A L L D I M E N S I O N S

E Series Cooktop Wall Hoods

Model ICTEWH30I

250 mm

790 mm

1210 mm

OVERALL

HEIGHT

274 mm

200 mm

620 mm

450 mm

OVERALL DEPTH

510 mm

80 mm

762 mm

OVERALL WIDTH

Models ICTEWH36 and ICTEWH36I

250 mm

790 mm

1210 mm

OVERALL

HEIGHT

274 mm

200 mm

620 mm

450 mm

OVERALL DEPTH

510 mm

80 mm

914 mm

OVERALL WIDTH

Model ICTEWH45

250 mm 274 mm

200 mm

620 mm

790 mm

1210 mm

OVERALL

HEIGHT

450 mm

OVERALL DEPTH

510 mm

80 mm

1143 mm

OVERALL WIDTH

O V E R A L L D I M E N S I O N S

E Series Cooktop Island Hood — Model ICTEIH42

297 mm 251 mm

790 mm

1210 mm

OVERALL

HEIGHT

222 mm

642 mm

488 mm

80 mm

1067 mm

OVERALL WIDTH

550 mm

OVERALL DEPTH

S P E C I F I C A T I O N S

Model ICTEWH30I

Hood Type

Overall Width

Overall Height

(excluding chimney)

Overall Height

(including chimney)

Maximum Height

(full extension)

Overall Depth

Bottom of Hood to Countertop

Duct Size

Discharge

Internal Blower

Electrical Supply

Shipping Weight

(shell only)

Wall Hood

762 mm

80 mm

790 mm

1210 mm

450 mm

650 mm to 760 mm

150 mm Round

Vertical

500 CFM included

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

18 kg

S P E C I F I C A T I O N S

Models ICTEWH36 and ICTEWH36I

Hood Type

Overall Width

Overall Height

(excluding chimney)

Overall Height

(including chimney)

Maximum Height

(full extension)

Overall Depth

Bottom of Hood to Countertop

Duct Size

Discharge

Internal Blower

Blower Options

Electrical Supply

Shipping Weight

(shell only)

Wall Hood

914 mm

80 mm

790 mm

1210 mm

450 mm

650 mm to 760 mm

150 mm Round

Vertical

500 CFM included with

Model ICTEWH36I

Contact your

Wolf dealer

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

21 kg

*Blower options vary with the cooking surface. Refer to the cooktop ventilation recommendations on pages 68–69.

W O L F C O O K T O P V E N T I L A T I O N

I N S T A L L A T I O N S P E C I F I C A T I O N S

E Series Cooktop Wall Hoods

S P E C I F I C A T I O N S

Model ICTEWH45I

Hood Type

Overall Width

Overall Height

(excluding chimney)

Overall Height

(including chimney)

Maximum Height

(full extension)

Overall Depth

Bottom of Hood to Countertop

Duct Size

Discharge

Internal Blower

Electrical Supply

Shipping Weight

(shell only)

Wall Hood

1143 mm

80 mm

790 mm

1210 mm

450 mm

650 mm to 760 mm

150 mm Round

Vertical

500 CFM included

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

26 kg

450 mm

OVERALL DEPTH

1210 mm

MAXIMUM

HEIGHT

OF HOOD

2.4 m TO 2.7 m

FLOOR TO

CEILING HEIGHT

650 mm

760 mm

TO COUNTERTOP

762 mm,

914 mm

OR 1143 mm

OVERALL WIDTH

790 mm

MINIMUM

HEIGHT

OF HOOD

S P E C I F I C A T I O N S

Model ICTEIH42I

Hood Type

Overall Width

Overall Height

(excluding chimney)

Overall Height

(including chimney)

Maximum Height

(full extension)

Overall Depth

Bottom of Hood to Countertop

Duct Size

Discharge

Internal Blower

Electrical Supply

Shipping Weight

(shell only)

Island Hood

1067 mm

80 mm

790 mm

1210 mm

550 mm

650 mm to 760 mm

150 mm Round

Vertical

500 CFM included

220-240 V AC, 50/60 Hz

15 amp dedicated circuit

32 kg

I N S T A L L A T I O N S P E C I F I C A T I O N S

E Series Cooktop Island Hood

550 mm

OVERALL DEPTH

1210 mm

MAXIMUM

HEIGHT

OF HOOD

2.4 m TO 2.7 m

FLOOR TO

CEILING HEIGHT

650 mm

760 mm

TO COUNTERTOP

1067 mm

OVERALL WIDTH

790 mm

MINIMUM

HEIGHT

OF HOOD

W O L F C O O K T O P V E N T I L A T I O N

B L O W E R C O N S I D E R A T I O N S

Except for Model ICTEWH36, which is shipped without a blower assembly, E Series cooktop hoods include a 500 CFM internal blower. Wolf internal and remote blowers are available for

Model ICTEWH36. Models with an internal blower can also use the charcoal filter if the hood will not be ducted to the outside. Charcoal filters are available as a sales accessory. Contact your local Wolf dealer for more information on remote blowers and charcoal filters.

For Model ICTEWH36, the blower will vary in size when ducted to the outside. Blower size is dictated by the cooking surface, the volume of air to be moved and the length of the duct run.

A straight, short duct run with a limited number of elbows and transitions will allow the ventilation hood to perform most efficiently.

A remote-mounted blower will minimize the amount of blower noise, but will not eliminate the noise completely. All remote blowers will require a transition to a 254 mm duct.

D U C T I N G C O N S I D E R A T I O N S

IMPORTANT NOTE: E Series cooktop hoods can be ducted to the outside or using a sales accessory charcoal filter, in a non-ducting installation

(internal blower (I) models only).

Wolf cooktop wall and island hoods have an

150 mm round vertical discharge. Ducting can run through the roof, external wall or eave.

Ducting through an eave requires an internal blower. Refer to the illustrations below.

E Series cooktop wall and island hoods will operate most efficiently when ductwork does not exceed 15 m in length.

Local building codes may require the use of make-up air. Consult your local HVAC professional for specific requirements in your area.

D U C T I N G C O N S I D E R A T I O N S

E Series Cooktop Wall Hoods E Series Cooktop Island Hood

ROOF CAP OR REMOTE BLOWER

150 mm ROUND DUCT

790 mm

1210 mm

HEIGHT

OF HOOD

TELESCOPIC

CHIMNEY FLUE

150 mm ROUND

ELBOW

80 mm

450 mm

HOOD DEPTH

650 mm

760 mm

COUNTERTOP

TO BOTTOM

OF HOOD

DUCTWORK INSTALLATION

THROUGH ROOF

WALL CAP

OR REMOTE BLOWER

DUCTWORK INSTALLATION

THROUGH WALL

150 mm ROUND

VERTICAL DISCHARGE

DUCTWORK INSTALLATION

THROUGH ROOF

ROOF CAP OR REMOTE BLOWER

150 mm ROUND DUCT

TELESCOPIC

CHIMNEY FLUE

790 mm

1210 mm

HEIGHT

OF HOOD

80 mm

550 mm

OVERALL DEPTH

650 mm

760 mm

COUNTERTOP

TO BOTTOM

OF HOOD

150 mm ROUND

ELBOW

EAVE VENT

150 mm ROUND

VERTICAL

DISCHARGE

DUCTWORK

INSTALLATION

THROUGH

EAVE –

INTERNAL

BLOWER ONLY

W O L F C O O K T O P V E N T I L A T I O N

Model DD30

Model DD36

Model DD45

W O L F D O W N D R A F T S Y S T E M S

The cooktop downdraft unit rises from the countertop to whisk away odors and smoke into the easy-to-clean, five-layer mesh filter. The control module and top cover are available in classic stainless steel.

Wolf downdraft systems come in 762 mm,

914 mm and 1143 mm widths and are recommended for use with Wolf framed electric cooktops, gas cooktops and integrated modules.

IMPORTANT NOTE: Wolf downdraft ventilation systems are not recommended for use with the electric grill, steamer and fryer modules.

A downdraft can be used with sealed burner rangetop Model ICBSRT304. An accessory trim kit is necessary for this installation. Contact your

Wolf dealer for details.

F E A T U R E S

Classic stainless steel control module and top cover

Remote-mounted control module

Internal, in-line and remote blower options

Three-speed blower control

Filter clean timer lets you know when the filter needs cleaning

Delay-off feature automatically turns unit off after five minutes, chimney remains up

Stainless steel filter cover with dishwasher-safe aluminum mesh filter

LED indicators

Downdraft control kit, available as a sales accessory for Models DD30 and DD36 (included with Model DD45)—includes control module, top cover, mounting brackets, RJ45 connector and mounting hardware

D O W N D R A F T S Y S T E M F E A T U R E S

Model DD36 shown

Top cover

Aluminum mesh filters

Stainless steel filter covers

Location of rating plate

Remote-mounted control module

A C C E S S O R I E S

Downdraft Systems

Bracket supports for installation of two integrated modules with

762 mm downdraft

SRT/Downdraft trim kit for sealed burner rangetop Model

ICBSRT304

Transitions in various sizes

Accessories are available through your

Wolf dealer.

229 mm chimney elevation

Three-speed blower control

M O D E L O P T I O N S

Downdraft Systems

(I) Models

500 CFM internal blower included

762 mm Width

914 mm Width

1143 mm Width

DD30I

DD36I

DD45I

(R) Models

Remote blower required

762 mm Width

914 mm Width

1143 mm Width

DD30R

DD36R

DD45R

C O N T R O L K I T O P T I O N S

Downdraft Systems

Model DD30I / DD30R

Classic DD30CONTROL/S

Model DD36I / DD36R

Classic DD36CONTROL/S

Control module and top cover have the stainless steel finish. Control kits also include mounting brackets, RJ45 connector and hardware and are ordered and shipped as sales accessories for Models

DD30 and DD36. Control kit components are included with Model DD45.

W O L F C O O K T O P V E N T I L A T I O N

P L A N N I N G I N F O R M A T I O N

Wolf downdraft ventilation systems are available in 762 mm, 914 mm and 1143 mm widths. The downdraft should be at least as wide as the cooking surface.

Downdraft Model DD30 will fit most 762 mm wide cabinets, Model DD36 will fit most 914 mm wide cabinets and Model DD45 will fit most

1156 mm wide cabinets. It is recommended that oversized cabinets be used for easier installation.

Cabinet backs may need to be removed.

IMPORTANT NOTE: To install a downdraft system and a Wolf cooktop, you must allow for a minimum 638 mm flat counter space from front to back. A countertop with a raised lip and/or backsplash may not allow enough space for proper installation. 60 mm of flat countertop is required behind the cooktop and 44 mm is necessary between the back edge of the cooktop and inside of cabinet back.

IMPORTANT NOTE: This appliance must be used with a Wolf-approved control module and top cover.

The remote-mounted control module is available as a sales accessory for Models DD30 and DD36 and is included with Model DD45. Installation of the control module must be within 3 m of the downdraft assembly and a minimum of 102 mm from the outer edge of cooktop element or burner. You will be required to drill three holes and connect the downdraft to the control module with the provided wire.

Specifications on the following pages provide overall dimensions, blower and ducting considerations, and installation specifics for downdraft ventilation systems. Also refer to the cooktop ventilation recommendations on pages 68–69.

If a Model DD30 is installed in combination with two integrated modules, an integrated module support for downdraft ventilation is required.

Contact your Wolf dealer for information on accessory components.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

O V E R A L L D I M E N S I O N S

Downdraft Systems

Models DD30I / DD30R

762 mm

60 mm

Models DD36I / DD36R

914 mm

230 mm

667 mm

38 mm

DEPTH OF

DOWNDRAFT CHIMNEY

230 mm

819 mm

38 mm

DEPTH OF

DOWNDRAFT CHIMNEY

60 mm

Models DD45I / DD45R

1156 mm

230 mm

1048 mm

38 mm

DEPTH OF

DOWNDRAFT CHIMNEY

60 mm

W O L F C O O K T O P V E N T I L A T I O N

S P E C I F I C A T I O N S

Models DD30I / DD30R

Overall Width

Overall Height

(above countertop)

Overall Depth

Duct Size (DD30I)

Duct Size (DD30R)

Discharge

Blower (DD30I)

Blower Options*

(DD30R)

762 mm

230 mm

Electrical Supply

Power Cord

Shipping Weight

60 mm

83 mm x 254 mm

83 mm x 356 mm

Adjustable

500 CFM Internal

1100 CFM In-Line,

900, 1200 or 1500 CFM

Remote

220-240 V AC, 60 Hz

15 amp dedicated circuit

.8 m 3-prong

34 kg

S P E C I F I C A T I O N S

Models DD36I / DD36R

Overall Width

Overall Height

(above countertop)

Overall Depth

Duct Size (DD36I)

Duct Size (DD36R)

Discharge

Blower (DD36I)

Blower Options*

(DD36R)

Electrical Supply

Power Cord

Shipping Weight

914 mm

230 mm

60 mm

83 mm x 254 mm

83 mm x 356 mm

Adjustable

500 CFM Internal

1100 CFM In-Line,

900, 1200 or 1500 CFM

Remote

220-240 V AC, 60 Hz

15 amp dedicated circuit

.8 m 3-prong

36 kg

S P E C I F I C A T I O N S

Models DD45I / DD45R

Overall Width

Overall Height

(above countertop)

Overall Depth

Duct Size (DD45I)

Duct Size (DD45R)

Discharge

Blower (DD45I)

Blower Options*

(DD45R)

Electrical Supply

Power Cord

Shipping Weight

1156 mm

230 mm

60 mm

83 mm x 254 mm

83 mm x 356 mm

Adjustable

500 CFM Internal

1100 CFM In-Line,

900, 1200 or 1500 CFM

Remote

220-240 V AC, 60 Hz

15 amp dedicated circuit

.8 m 3-prong

39 kg

*Refer to the cooktop ventilation recommendations on pages 68–69.

I N S T A L L A T I O N S P E C I F I C A T I O N S

Downdraft Systems

44 mm min

BACK EDGE

OF COOKTOP

TO INSIDE OF

CABINET BACK *

8.7 mm

745 mm

COUNTERTOP

TO BOTTOM OF

AIR BOX

638 mm min

FLAT

COUNTERTOP

SPACE

638 mm min

OF FLAT COUNTERTOP *

16 mm

489 mm

COOKTOP CUT-OUT

DEPTH

60 mm

54 mm

83 mm

197 mm

127 mm

457 mm

92 mm

181 mm

610 mm min

CABINET DEPTH

* AREAS OF POTENTIAL INTERFERENCE

64 mm min

WITH NO

RAISED LIP *

914 mm

70 mm

686 mm

FOR MODEL DD30

838 mm

FOR MODEL DD36

1067 mm

FOR MODEL DD45

COOKTOP CUT-OUT

WIDTH

64 mm min

489 mm

COUNTERTOP TOP VIEW

W O L F C O O K T O P V E N T I L A T I O N

E L E C T R I C A L R E Q U I R E M E N T S

Wolf downdraft ventilation systems require a separate, grounded 120 V AC, 60 Hz power supply. The service should have its own 15 amp circuit breaker, and a grounded 3-prong receptacle should be located within the reach of the

.8 m power cord. The specific location of the outlet is not critical as long as it is within reach of the power cord that is located midway, top and bottom, on the right side of the downdraft.

IMPORTANT NOTE: If Model DD30 is to be installed in a 762 mm wide cabinet, Model DD36 in a 914 mm wide cabinet or Model DD45 in a

1156 mm wide cabinet, the electrical outlet cannot be located on the back wall of the cabinet. The outlet may be placed in adjacent cabinetry.

Locate electrical within the shaded area shown in the Installation Specifications illustrations.

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

You must follow all local codes and ordinances when installing your service.

B L O W E R C O N S I D E R A T I O N S

Except for Models DD30I, DD36I and DD45I, which include a 500 CFM internal blower, Wolf downdrafts are shipped without the blower assembly. In-line and remote blower assemblies are available. The blower will vary in size and is dictated by the cooking surface, the volume of air that needs to be moved and the length of the duct run. A straight, short duct run with a limited number of elbows and transitions will allow the ventilation hood to perform most efficiently.

Wolf downdraft ventilation systems are designed for use with 83 mm x 254 mm ductwork for

Models DD30I, DD36I and DD45I and 83 mm x

356 mm ductwork for Models DD30R, DD36R and DD45R. Each can be transitioned to 203 mm or 254 mm round ductwork.

A remote-mounted blower will minimize the amount of blower noise, but will not eliminate the noise completely.

IMPORTANT NOTE: Install this downdraft system only with a Wolf blower.

Refer to the cooktop ventilation recommendations on pages 68–69.

I N S T A L L A T I O N

Refer to installation instructions shipped with each Wolf product for detailed specifications.

I N S T A L L A T I O N S P E C I F I C A T I O N S

Location of Electrical Supply

610 mm min

CABINET DEPTH

102 mm min

89 mm E

254 mm

762 mm min

FOR MODEL DD30

914 mm min

FOR MODEL DD36

1156 mm min

FOR MODEL DD45

OPTIONAL

ELECTRICAL

LOCATION IN

ADJACENT RIGHT

SIDE CABINET

IMPORTANT NOTE:

Certain installations may require that the electrical supply be placed in an adjacent cabinet within reach of the power cord.

Choose the location shown in the illustration that best suits your installation.

W O L F C O O K T O P V E N T I L A T I O N

D U C T I N G C O N S I D E R A T I O N S

Wolf downdraft systems have an adjustable discharge that will allow you to negotiate ducting around floor joists and other obstacles.

Three different discharge locations are available with side-to-side adjustment for accurate alignment of ductwork. Refer to the illustration below for discharge location and adjustment.

IMPORTANT NOTE: All Wolf downdraft systems must be vented to the outside. Use only metal ductwork.

For best performance, 254 mm round ductwork is recommended. The downdraft will operate most efficiently when ductwork does not exceed

12 m in length.

Choose the ducting option that allows the shortest length of ductwork and a minimum number of elbows and transitions. Refer to the illustration below for ducting options.

D I S C H A R G E L O C A T I O N

Downdraft Systems

D U C T I N G O P T I O N S

Downdraft Systems

CENTERLINE OF COUNTERTOP CUT-OUT

562 mm

INTERNAL BLOWER

483 mm

IN-LINE OR

REMOTE BLOWER

LEFT

DISCHARGE

LOCATION

RIGHT

DISCHARGE

LOCATION

140 mm

INTERNAL BLOWER

108 mm

IN-LINE OR

REMOTE BLOWER

416 mm

INTERNAL BLOWER

546 mm

IN-LINE OR

REMOTE BLOWER

DISCHARGE CUT-OUT

DIMENSIONS:

260 mm x 89 mm

INTERNAL BLOWER

362 mm x 89 mm

IN-LINE OR

REMOTE BLOWER

CENTERLINE OF COUNTERTOP CUT-OUT

ADJUSTMENT:

25 mm – 178 mm

INTERNAL BLOWER

165 mm MAX

IN-LINE OR

REMOTE BLOWER

ADJUSTMENT:

127 mm MAX

IN-LINE OR

REMOTE BLOWER

BOTTOM

DISCHARGE

LOCATION

140 mm

INTERNAL BLOWER

108 mm

IN-LINE OR

REMOTE BLOWER

NOTE: Measurements are to centerline of duct cut-outs

254 mm

ROUND

REMOTE

BLOWER

WALL CAP

305 mm

MIN TO

GROUND

INTERNAL BLOWER

INSTALLATION THROUGH WALL

REMOTE

BLOWER

254 mm

ROUND

REMOTE BLOWER

ROOF MOUNT INSTALLATION

305 mm

MIN TO

GROUND

305 mm

MIN TO

GROUND

INTERNAL BLOWER

INSTALLATION THROUGH WALL

REMOTE BLOWER

INSTALLATION THROUGH WALL

W O L F V E N T I L A T I O N R E C O M M E N D A T I O N S

W O L F B L O W E R A S S E M B L I E S

A ventilation system must include a blower assembly. An internal, in-line or remote blower assembly must be selected to accommodate the cooking appliance, CFM requirements and homeowner preferences. Internal, in-line and remote blower assemblies are available as sales accessories through your Wolf dealer.

Internal blowers are mounted inside the hood canopy or downdraft blower box.

Wolf in-line blowers are mounted between the downdraft and the exterior of the home. Ducting runs from the downdraft and connects to the blower. More ducting is attached to the other side of the blower and runs to the exterior of the home. An in-line blower is a good option for those who do not want the blower mounted inside the downdraft but cannot, or prefer not to, mount a remote blower on the exterior of the home.

Remote blowers can be mounted on the roof or, in some cases, on an exterior wall. A remotemounted blower will minimize the amount of blower noise but will not eliminate the noise completely.

Wolf internal, in-line and remote blowers are for use with Wolf downdraft systems.

Cooktop ventilation recommendation charts on pages 68–69 provide minimum CFM recommendations according to the cooking appliance and ventilation system used and blower options for each specific downdraft.

Refer to the illustrations below for dimensions of

Wolf in-line and remote blowers. Installation instructions shipped with each Wolf ventilation product provide detailed specifications. These instructions can also be found on our website, wolfappliance.com.

A C C E S S O R I E S

Blower assemblies are available through your Wolf dealer.

I N - L I N E B L O W E R

632 mm

457 mm 305 mm

559 mm

203 mm

457 mm

BLOWER-110IL

R E M O T E B L O W E R S

718 mm

394 mm

527 mm

254 mm

Diameter

622 mm

356 mm

629 mm

121 mm

BLOWER-60REM and

BLOWER-90REM

749 mm

375 mm

254 mm

Diameter

533 mm

254 mm

749 mm

264 mm

635 mm

BLOWER-150REM

184 mm

749 mm

375 mm

254 mm

Diameter

457 mm

254 mm

749 mm

257 mm

559 mm

BLOWER-120REM

184 mm

W O L F V E N T I L A T I O N R E C O M M E N D A T I O N S

C O O K T O P V E N T I L A T I O N C F M R E C O M M E N D A T I O N S

D O W N D R A F T S

DD30 DD36

Electric Cooktops

Model ICT15E

Model ICT30E

Model ICT36E

C F M

Recommendations are based on total kW output. Wolf recommends 1 CFM per .03 kW.

Additional CFM may be required for charbroilers, griddles and long duct runs.

Gas Cooktops

Model ICBCT15G

Model ICBCT30G

Model ICBCT36G

Integrated Modules

Model CT15I

Model IIM15

215*

500

DD30

215*

500

DD30

500

DD36

500

DD36

215*

DD30 DD36

Sealed Burner Rangetops

Model ICBSRT304 600

*Use these recommendations to determine total CFM when installing multiple cooktops or modules.

DD45

150*

350

DD45

150*

350

DD45

150*

DD45

W O L F V E N T I L A T I O N R E C O M M E N D A T I O N S

C O O K T O P V E N T I L A T I O N B L O W E R O P T I O N S

D O W N D R A F T S Y S T E M S

Blower Description

500 CFM Internal

1100 CFM In-Line

900 CFM Remote

1200 CFM Remote

1500 CFM Remote

Blower Number

Included with (I) Models

BLOWER-110IL (808332)

BLOWER-90REM (801641)

BLOWER-120REM (801642)

BLOWER-150REM (804701)

Downdraft Models

DD30I / DD36I / DD45I

DD30R / DD36R / DD45R

Adjustable discharge. 83 mm x 254 mm duct for internal blower, no transition required. 83 mm x 356 mm duct for in-line and remote blowers. TRANS-14-10 required for remote blowers.

I M P O R T A N T

N O T E

Blower configurations are for reference only. Refer to the minimum CFM recommendations for your specific cooking appliance. Consult a qualified HVAC engineer for specific installation and ducting applications.

The information and images in this guide are the copyright property of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc.

8 1 0 2 9 5 8 / 2 0 0 7

WOLF APPLIANCE, INC.

P O BOX 44848

MADISON, WI 53744 USA

WOLFAPPLIANCE.COM

Hello! I am an AI chatbot specifically trained to assist you with the Wolf IDF364C Design Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated