Carrier | E2SF-13 | Micro Motion Model RFT9739

Product Data Sheet
PS-00024, Rev. A
February 2004
Micro Motion® Model RFT9739
Mass Flow and Density Transmitter
TM
Micro Motion
Micro Motion® Model RFT9739 transmitter
Precise, multivariable measurement
Digital communications
The RFT9739 transmitter works with Micro Motion
sensors to provide precision fluid measurement in
a wide variety of fluid applications. The RFT9739
has modular, microprocessor-based electronics,
incorporating ASIC digital technology with a
choice of digital communication protocols.
The RFT9739 features user-selected Bell 202 or
RS-485 serial standard for HART® or Modbus®
communication protocol. For configuration in the
field, use Micro Motion Prolink® II software,
Emerson Process Management AMS software, or
a Model 275 or 375 HART Communicator.
Combined with a Micro Motion sensor, the
RFT9739 provides accurate mass flow, density,
temperature, and volumetric measurements of
process fluids. With a pressure transmitter
properly installed in the flow loop, the transmitter
also indicates pressure.
Four simultaneous output signals
The RFT9739 simultaneously transmits four
output signals. Two independently configured
analog outputs can each indicate flow rate,
density, temperature, or pressure. A frequency/
pulse output indicates flow rate or total. A control
output indicates flow direction, a fault, or
flowmeter zero in progress.
An integral liquid crystal display (LCD) is standard
on the rack-mount model, optional with the fieldmount version. Use the display to set
communication parameters, read process
variables, reset flow totalizers, and view
diagnostic messages.
Field-mount or rack-mount
The RFT9739 is available in field-mount and rackmount versions. The field-mount transmitter is
housed in a NEMA 4X (IP65) explosion-proof
enclosure that provides easy access to the
electronics module, and allows the transmitter and
sensor to be installed in the same hazardous
area. The rack-mount transmitter's compact
housing is ideal for control room installations.
2
Micro Motion® Model RFT9739 Transmitter
Operates with a variety of sensors
Choose from a wide range of sensors to suit your
application. The RFT9739 is compatible with
Micro Motion ELITE® sensors, the most accurate
Coriolis meters available today. Or choose Micro
Motion F-Series sensors, H-Series hygienic
sensors, standard or high-pressure Model D
sensors, Model DT high-temperature sensors, or
Model DL sanitary sensors.
Mass flow performance
Accuracy (1)
ELITE
F-Series
H-Series
D (except D38), DT, DL
D38
Liquid
±0.10% ±  --------------------------------- × 100 % of rate
flow rate
Gas
±0.50% ±  --------------------------------- × 100 % of rate
flow rate
Liquid
±0.20% ±  --------------------------------- × 100 % of rate
flow rate
Gas
±0.70% ±  --------------------------------- × 100 % of rate
flow rate
Liquid
±0.15% ±  --------------------------------- × 100 % of rate
flow rate
Gas
±0.70% ±  --------------------------------- × 100 % of rate
flow rate
Liquid
±0.15% ±  --------------------------------- × 100 % of rate
flow rate
Gas
±0.65% ±  --------------------------------- × 100 % of rate
flow rate
Liquid
±0.15% ±  --------------------------------- × 100 % of rate
flow rate
Gas
±0.50% ±  --------------------------------- × 100 % of rate
flow rate
zero stability
zero stability
zero stability
zero stability
zero stability
zero stability
zero stability
zero stability
zero stability
zero stability
(1) Flow accuracy includes the combined effects of repeatability, linearity, and hysteresis. All specifications are based on reference
conditions of water at 68 to 77°F (20 to 25 °C) and 15 to 30 psig (1 to 2 bar) unless otherwise noted. For gas measurement
specifications and values of zero stability, refer to product specifications for each sensor.
Micro Motion® Model RFT9739 Transmitter
3
Mass flow performance continued
Repeatability
ELITE
F-Series
H-Series
D (except DH38), DT, DL
DH38
4
Micro Motion® Model RFT9739 Transmitter
Liquid
±0.05% ± ½  --------------------------------- × 100 % of rate
flow rate
Gas
±0.25% ±  --------------------------------- × 100 % of rate
flow rate
Liquid
±0.10% ± ½  --------------------------------- × 100 % of rate
flow rate
Gas
±0.35% ±  --------------------------------- × 100 % of rate
flow rate
Liquid
±0.10% ± ½  --------------------------------- × 100 % of rate
flow rate
Gas
±0.35% ±  --------------------------------- × 100 % of rate
flow rate
Liquid
±0.05% ± ½  --------------------------------- × 100 % of rate
flow rate
Gas
±0.30% ±  --------------------------------- × 100 % of rate
flow rate
Liquid
±0.05% ± ½  --------------------------------- × 100 % of rate
flow rate
Gas
±0.25% ±  --------------------------------- × 100 % of rate
flow rate
zero stability
zero stability
zero stability
zero stability
zero stability
zero stability
zero stability
zero stability
zero stability
zero stability
Density performance
Accuracy (1)
Repeatability
g/cc
kg/m3
ELITE (except CMF010P)
Liquid
Gas
±0.0005
±0.002
±0.5
±2.0
CMF010P
Liquid
Gas
±0.002
±0.008
±2.0
±8.0
F-Series
Liquid only
±0.002
±2.0
H-Series
Liquid only
±0.002
±2.0
DH100, DH150
Liquid only
±0.002
±2.0
DH38
Liquid only
±0.004
±4.0
DL65, DT65, DT100, D150,
DT150, DH300
Liquid only
±0.001
±1.0
D300, D600, DL100, DL200
Liquid only
±0.0005
±0.5
ELITE (except CMF010P)
Liquid
Gas
±0.0002
±0.001
±0.2
±1.0
CMF010P
Liquid
Gas
±0.001
±0.004
±1.0
±4.0
F-Series
Liquid only
±0.001
±1.0
H-Series
Liquid only
±0.001
±1.0
DH100, DH150
Liquid only
±0.001
±1.0
DH38
Liquid only
±0.002
±2.0
DL65, DT65, DT100, D150,
DT150, DH300
Liquid only
±0.0005
±0.5
D300, D600, DL100, DL200
Liquid only
±0.002
±2.0
(1) Flow accuracy includes the combined effects of repeatability, linearity, and hysteresis. All specifications are based on reference
conditions of water at 68 to 77°F (20 to 25 °C) and 15 to 30 psig (1 to 2 bar) unless otherwise noted. For gas measurement
specifications and values of zero stability, refer to product specifications for each sensor.
Temperature performance
Accuracy
All sensors
±1 °C ±0.5% of reading in °C
Repeatability
All sensors
±0.2 °C
Micro Motion® Model RFT9739 Transmitter
5
Output signals
Analog outputs
Functional capabilities
Two independently configured analog outputs, designated as primary and secondary, can
represent mass or volumetric flow rate, density, temperature, event 1 or event 2.
• With a pressure transmitter, outputs can also provide indication for pressure
• Internally powered, can be selected as 4-20 mA or 0-20 mA current outputs; cannot be
changed from active to passive
• Galvanically isolated to ±50 VDC, 1000 ohm load limit
• Out-of-range capability:
0-22 mA on 0-20 mA output
3.8-20.5 mA on 4-20 mA output
Milliamp (mA) output
rangeability
Flow
• Maximum span determined by sensor specifications
• Range limit determined by sensor maximum rate
• Minimum recommended span (% of nominal flow range):
ELITE sensors
2.5%
F-Series and H-Series sensors
10%
D, DT, and DL sensors
10%
D300 and D600 sensors
5%
High-pressure (DH) sensors
20% typical
Density
Range limit
Minimum span
0 to 5 g/cc (0 to 5000 kg/m³)
0.05 g/cc (50 kg/m³)
Temperature
Range limit
Minimum span
–400 to +842 °F (–240 to +450 °C)
36 °F (20 °C)
Frequency outputs
One frequency/pulse output can be configured to indicate mass flow rate, volumetric flow rate,
mass total (inventory), or volume total (inventory), independent of analog outputs.
• Internally powered, 0-15 V square wave, unloaded; internal 2.2 kohm pull-up resistor to 15 V,
galvanically isolated to ±50 VDC
• In open collector configuration: sinking capability, 0.1 amps in “on” condition (0 volt level), 30
VDC compliance in “off” condition
• Signal can be scaled up to 10,000 Hz
• Out-of-range capability to 15,000 Hz
• Programmable pulse width for low frequencies
Dual-channel frequency (rack-mount transmitter only)
The dual-channel frequency output is approved for custody transfer applications. The two
channels are referred to as frequency A and frequency B.
• Phase shift between channels is 90 degrees
• Output derived from the primary frequency, and represents the same process variable as the
frequency/pulse output, but with half the frequency
• All specifications match frequency/pulse output except:
- Signal can be scaled up to 5,000 Hz
- Out-of-range capability to 7500 Hz
• The output complies with VDE/VDI 2188 when jumper JP1 is installed
6
Micro Motion® Model RFT9739 Transmitter
Output signals continued
Control
One control output can represent flow direction, fault alarm, zero in progress,
event 1 or event 2.
• Internally powered, digital level 0 or 15 V, 2.2 kohm pull-up, galvanically isolated to ±50 VDC
• In open collector configuration: sinking capability, 0.1 amps in “on” condition (0 volt level), 30
VDC compliance in “off” condition
Communication
Switch allows selection of Bell 202 and/or RS-485 serial standard
• Bell 202 signal is superimposed on primary variable mA output and is available for host
system interface
- Frequency 1.2 and 2.2 kHz, amplitude 0.8 V peak-to-peak, 1200 baud
- Requires 250 to 1000 ohms load resistance
• RS-485 signal is a ±5 V square wave referenced to transmitter ground. Baud rates between
1200 baud and 38.4 kilobaud can be selected.
Additional outputs
Sensor frequency
For use with Micro Motion peripheral devices, 8 V peak-to-peak at sensor natural frequency,
referenced to sensor ground, 10 kohm output impedance
Sensor temperature
For use with Micro Motion peripheral devices, 5 mV/°C, referenced to signal ground, 10 kohm
output impedance
API gravity
API gravity references to 60 °F (15 °C). Uses correlation based on API equation 2540 for
Generalized Petroleum Products
Minimum 4-20 mA span: 10 °API
Accuracy of corrected density calculation relative to API-2540 from 0 to +300 °F
(–18 to +149 °C):
Standard volume
Process fluid
g/cc
kg/m3
Diesel, heater, and fuel oils
Jet fuels, kerosenes, and solvents
Crude oils and JP4
Lube oils
Gasoline and naphthenes
±0.0005
±0.002
±0.004
±0.01
±0.02
±0.5
±2.0
±4.0
±10
±20
°API
±0.2
±0.5
±1.0
±2.0
±5.0
Outputs standard volume at 60 °F or 15 °C for Generalized Petroleum Products when °API is
selected as density unit of measure
• Accuracy of standard volume measurements depends on accuracies of mass flow rate,
density, temperature and temperature-corrected °API calculation, and can be estimated
using the root mean square method
• Standard volume accuracy of ±0.5% of rate is typically attainable for Generalized Petroleum
Products such as fuel oils, jet fuels, and kerosenes
Micro Motion® Model RFT9739 Transmitter
7
Output signals continued
Pressure compensation
The analog input can accept a signal from a pressure transmitter for pressure
compensation of flow and density.
• Range 0-25 mA
• Can be used to power independent pressure or differential pressure transmitter
• Voltage sourcing capability 15 V
• Input impedance 100 ohms
Low-flow cutoff
Flow values below the user-defined low-flow cutoff cause the digital, mA, and frequency
outputs to default to zero flow levels. Each mA output may be configured for an additional
low-flow cutoff.
Slow-flow limits
Transmitter senses density outside limits. Flow output remains at last measured value, for a
programmed time of 0 to 60 seconds, before defaulting to zero flow.
Damping
Wide range of programmed filter time constants for damping on flow, density, and
temperature. Additional damping may be applied to mA outputs.
Fault indication
Faults can be indicated by user-selected downscale (0–2 mA, 0 Hz) or upscale (22–24 mA,
15–19 kHz) output levels. The control output can also be configured to indicate a fault
condition at 0 V.
Output testing
Current source
Frequency source
Local display (optional)
8
Transmitter can produce a user-specified current between 0
and 22 mA on a 0–20 mA output, or between 2 and 22 mA
on a 4–20 mA output.
Transmitter can produce a user-specified frequency between
0.1 and 15,000 Hz.
Optional for field-mount transmitter; standard on rack-mount transmitter.
• Display is a 2-line, 16-character, alphanumeric liquid crystal display (LCD)
• Using the scroll function, the user can view flow rate, density, temperature, mass and
volume totals and inventory levels, and status messages
• A reset button allows the user to reset the transmitter’s flow totalizers and communication
parameters, and perform the flowmeter zeroing procedure
Micro Motion® Model RFT9739 Transmitter
Power supply options
Field-mount transmitter
The internal power supply of the field-mount RFT9739 transmitter is one of the following
(power codes 4 or 5):
• 85 to 250 VAC (1), 48 to 62 Hz, 10 watts typical, 15 watts maximum, fused in
accordance with IEC 127-3 400mA/250V, time-lag, subminiature
• 12 to 30 VDC (2), 7 watts typical, 14 watts maximum, fused in accordance with IEC
127-3 1.6A/125V, time-lag, subminiature
Rack-mount transmitter
The internal power supply of the rack-mount RFT9739 transmitter is one of the following
(power codes 1, 2, or 3):
• 110/115 VAC ± 25%••(1), 48 to 62 Hz, 10 watts typical, 15 watts maximum, fused in
accordance with UL/CSA 250mA/250V, time-lag, 5 × 20 mm
• 220/230 VAC ± 25%(1), 48 to 62 Hz, 10 watts typical, 15 watts maximum, fused in
accordance with UL/CSA 250mA/250V, time-lag, 5 × 20 mm
• 12 to 30 VDC (3), 7 watts typical, 14 watts maximum, fused in accordance with UL/CSA
2A/125V, medium-lag, 5 × 20mm
(1) All AC-powered RFT9739 transmitters comply with low-voltage directive 73/23/EEC per IEC 1010-1 with Amendment 2.
(2) At startup, transmitter power source must provide a minimum of 1.6 amperes of short-term current at a minimum of 12 volts at the
transmitter's power input terminals.
(3) At startup, transmitter power source must provide a minimum of 2 amperes of short-term current at a minimum of 12 volts at the
transmitter's power input terminals.
Temperature limits
Ambient temperature
Field-mount transmitter
Field-mount transmitter
Rack-mount transmitter
°C
Without display
Operating
Storage
–22 to +131
–40 to +176
–30 to +55
–40 to +80
With display
Operating
Storage
+14 to +131
–4 to +158
–10 to +55
–20 to +70
Operating
Storage
+32 to +122
–4 to +158
0 to +50
–20 to +70
UL
ATEX
+131 maximum
–22 to +113
+55 maximum
–30 to +45
UL
ATEX
+131 maximum
–4 to +131
+55 maximum
–20 to +55
Rack-mount transmitter
Approval temperature
°F
All models
Micro Motion® Model RFT9739 Transmitter
9
Environmental limits and effects
Humidity limits
Meets SAMA PMC 31.1-1980
Vibration limits
Field-mount transmitter
Rack-mount transmitter
Meets SAMA PMC 31.1-1980, Condition 2
Meets SAMA PMC 31.1-1980, Condition 1
EMI effect
Field-mount transmitter
Field-mount RFT9739 transmitters with enhanced EMI
immunity meet the requirements of the EMC directive 89/336/
EEC per EN 50081-1 (August 1993) and EN 50082-2 (March
1995) when operated at nominal rated flow measurement
range. Enhanced EMI immunity is required for transmitters
installed in the European Community after 1 January 1996.
For specific EMC effects within the EC, the Technical EMC file
may be reviewed at Emerson Process Management
Veenendaal.
Environmental effects
Ambient temperature effect
10
All RFT9739 transmitters meet the requirements of SAMA
PMC 33.1 (October 1978), Class 1, A, B, C (0.6% span) at
nominal flow rate. All RFT9739 transmitters meet the
recommendations of ANSI/IEEE C62.41 (1991) for surge and
EFT.
To meet the above specifications, the transmitter must be
installed with an approved Micro Motion sensor, and the
sensor cable must be either double-shielded with full contact
glands, or installed in continuous, fully bonded metallic
conduit. The transmitter and sensor must be directly
connected to a low-impedance (less than 1 ohm) earth
ground. Transmitter outputs must be run in standard twistedpair, shielded instrument wire.
On mA outputs
On temperature output
On mA input
Micro Motion® Model RFT9739 Transmitter
±0.005% of span/°C
±0.01°C/°C
±0.01% of span/°C
Field-mount RFT9739 hazardous area classifications
When properly installed with an approved sensor, the RFT9739 field-mount transmitter can be installed in the areas described
below. UL is a U.S.A. approvals agency. CSA is a Canadian approvals agency that provides approvals accepted both in the
U.S.A. and in Canada. SAA is an Australian approvals agency. ATEX is a European directive.
UL and CSA
Transmitter without display
Transmitter: Class I, Div. 1, Groups C and D. Class II, Div. 1,
Groups E, F, and G explosion proof when installed with
approved conduit seals. Otherwise, Class I, Div. 2, Groups A, B,
C, and D.
Outputs: Provides nonincendive sensor outputs for use in
Class I, Div. 2, Groups A, B, C, and D; or intrinsically safe
sensor outputs for use in Class I, Div. 1, Groups C and D, or
Class II, Div. 1, Groups E, F, and G.
Transmitter with display
Transmitter: Class I, Div. 2, Groups A, B, C, and D.
Outputs: Provides nonincendive sensor outputs for use in
Class I, Div. 2, Groups A, B, C, and D; or intrinsically safe
sensor outputs for use in Class I, Div. 1, Groups C and D, or
Class II, Div. 1, Groups E, F, and G.
Parameter
VOC
SAA
ATEX
UL Division 2 nonincendive parameters
Analog output
Frequency/pulse output
(Terminals 17-18, 19-20)
(Terminals 14-16)
ISC
Ca
La
36.5 V
22 mA
0.135 µf
100 mH
16 V
51 mA
1.5 µf
37 mH
Transmitter without display
Exd [ib] IIC T4 IP66
Transmitter with display
Ex [ib] IIC IP66
Transmitter without display
II2G EExd[ib] IIC T6
II(2)G [EExib] IIC
Transmitter with display
II(2)G [EExib] IIC
Flameproof transmitter
Safe area transmitter
Micro Motion® Model RFT9739 Transmitter
11
Rack-mount RFT9739 hazardous area classifications
When properly installed with an approved sensor, the RFT9739 rack-mount transmitter can be installed in the areas described
below. UL is a U.S.A. approvals agency. CSA is a Canadian approvals agency that provides approvals accepted both in the
U.S.A. and in Canada. ATEX is a European directive.
UL
Non-hazardous locations. Provides nonincendive sensor outputs for use in Class I, Div. 2,
Groups A, B, C, and D; or intrinsically safe sensor outputs for use in Class I, Div. 1, Groups C
and D, or Class II, Groups E, F, and G.
CSA
Non-hazardous locations. Connections to sensor are intrinsically safe for use in Class I, Div. 1,
Groups C, D, and Class II, Groups E, F, and G.
ATEX
Safe area only. Connections to sensor are intrinsically safe in [EEx ib] IIC areas.
12
Micro Motion® Model RFT9739 Transmitter
RFT9739 field-mount physical specifications
Weight (without display)
12.5 lb (5.7 kg)
Housing
NEMA 4X (IP65) epoxy polyester painted cast aluminum
Cable gland entrances
Three 3/4″ –14 NPT on transmitter base
Electrical connections
•
•
•
•
Screw terminal blocks for all signal wiring can be unplugged
Fixed screw terminals for power connections
Screw terminal on housing for chassis ground
Studs for intrinsic safety ground
Dimensions
Dimensions in
inches
(mm)
2 13/16
(71)
4X ∅
7 19/64
(185)
Optional
display
23/64
(9)
8 3/8
(213)
9 11/64
(233)
4 33/64
(115)
∅ 7 15/64
(184)
9 1/8
(232)
3x 3/4–14 NPT conduit opening
With display
Without
display
13 3/16
(335)
11 1/2
(292)
3/16
(5)
2 3/8
(60)
2 3/8
(60)
1 17/32
(39)
Minimum clearance for cover removal
Micro Motion® Model RFT9739 Transmitter
13
RFT9739 rack-mount physical specifications
Weight (without display)
4.4 lb (2.0 kg)
Housing
19-inch rack, European standard DIN 41494
128 mm (3HE) high × 142 mm (28TE) wide × 231.9 mm deep
Electrical connections
Two connectors per DIN 41612, type F
Choose either fast-on (wire-pin) solder connectors (standard) or Y-shaped
screw-terminal connectors (optional)
Sensor connectors and output connectors are not interchangeable
Dimensions
Dimensions in
inches
(mm)
5 17/32
(140.4)
Back panel with
DIN 41612 male
Y-shaped screw terminals
Back panel with
DIN 41612 male
fast-on/solder terminals
2 19/32
(66)
13TE
2 19/32
(66)
13TE
With Y-shaped
screw terminals
5 37/64
(141.7)
28TE
5
(127)
25TE
10 5/16
(261.9)
With fast-on/solder
terminals
10 1/16
(255.6)
9 15/64
(234.6)
8 23/64
(212.3)
4X M2.5 x 11
4 13/16
(122.4)
4 3/8
(111.1)
5 3/64
(128.4)
3HE
3/16
(4.7)
47/64
(18.7)
14
Micro Motion® Model RFT9739 Transmitter
Ordering information — RFT9739 field-mount with display
Code
Product description
RFT9739D
RFT9739 multivariable transmitter; remote field-mount; with display; NEMA 4X
Code
Power
4
85–205 VAC
5
12–30 VDC
Code
S
(1)
Configuration
Standard configuration (not CE compliant)
E
Enhanced EMI immunity (CE compliant)
Code
Approvals
M
Micro Motion standard (no approvals)
U
UL
C
CSA
Y
ATEX intrinsically safe sensor outputs
S (2)
SAA
Code
Conduit connections
A
No fittings or glands (for approval codes M, U, C, and Y)
B
1 gland; nickel-plated brass (for ATEX approval code Y only)
C
3 glands; nickel-plated brass (for ATEX approval code Y only)
Code
Language
A
Danish quick reference and English manual
D
Dutch quick reference and English manual
E
English quick reference and English manual
F
French quick reference and French manual
G
German quick reference and German manual
H
Finnish quick reference and English manual
I
Italian quick reference and English manual
N
Norwegian quick reference and English manual
O
Polish quick reference and English manual
P
Portuguese quick reference and English manual
S
Spanish quick reference and Spanish manual
W
Swedish quick reference and English manual
Code
Factory options
Z
Standard product
X
CEQ product
R
Restocked product (if available)
Typical model number:
RFT9739D 4 S C A E Z
(1) Not valid with approval code Y.
(2) Not valid with the DL065S, DS600S, or DT sensors.
Micro Motion® Model RFT9739 Transmitter
15
Ordering information — RFT9739 field-mount without display
Code
Product description
RFT9739E
RFT9739 multivariable transmitter; remote field-mount; NEMA 4X; explosion-proof
Code
Power
4
85–205 VAC
5
12–30 VDC
Code
S
(1)
Configuration
Standard configuration (not CE compliant)
E
Enhanced EMI immunity (CE compliant)
Code
Approvals
M
Micro Motion standard (no approvals)
U
UL
C
CSA
Y
ATEX intrinsically safe sensor outputs
W
S
(2)
Code
ATEX intrinsically safe sensor outputs; flameproof transmitter
SAA
Conduit connections
For approval code M (MMI standard):
A
No fittings or glands
B
1 gland; nickel-plated brass
C
3 glands; nickel-plated brass
For approval code U (UL):
J
1 explosion-proof seal fitting
K
1 explosion-proof seal fittings
For approval code C (CSA):
A
No fittings or glands
A
No fittings or glands
B
1 gland; nickel-plated brass
C
3 glands; nickel-plated brass
A
No fittings or glands
D
1 gland; nickel-plated brass
For approval code Y (ATEX intrinsically safe sensor outputs):
For approval code W (ATEX intrinsically safe sensor outputs; flameproof transmitter):
E
1 gland; stainless steel
F
3 glands; nickel-plated brass
G
3 glands; stainless steel
For approval code S (SAA):
A
No fittings or glands
Continued on next page.
(1) Not valid with approval codes Y and W.
(2) Not valid with the DL065S, DS600S, or DT sensors.
16
Micro Motion® Model RFT9739 Transmitter
Ordering information — RFT9739 field-mount without display continued
Code
Language
A
Danish quick reference and English manual
D
Dutch quick reference and English manual
E
English quick reference and English manual
F
French quick reference and French manual
G
German quick reference and German manual
H
Finnish quick reference and English manual
I
Italian quick reference and English manual
N
Norwegian quick reference and English manual
O
Polish quick reference and English manual
P
Portuguese quick reference and English manual
S
Spanish quick reference and Spanish manual
W
Swedish quick reference and English manual
Code
Factory options
Z
Standard product
X
CEQ product
R
Restocked product (if available)
Typical model number:
RFT9739E 4 S U J E Z
Micro Motion® Model RFT9739 Transmitter
17
Ordering information — RFT9739 rack-mount
Code
Product description
RFT9739R
RFT9739 multivariable transmitter; remote rack/panel mount
Code
Power
1
110/115 VAC
2
220/230 VAC
3
12–30 VDC
Code
Configuration
E
Enhanced EMI immunity (CE compliant)
Code
Approvals
M
Micro Motion standard (no approvals)
U
UL
C
CSA
Y
ATEX intrinsically safe sensor outputs
Code
Terminal connections
F
Fast-on/solder connections
S
Y-shaped screw terminals
Code
Language
A
Danish quick reference and English manual
D
Dutch quick reference and English manual
E
English quick reference and English manual
F
French quick reference and French manual
G
German quick reference and German manual
H
Finnish quick reference and English manual
I
Italian quick reference and English manual
N
Norwegian quick reference and English manual
O
Polish quick reference and English manual
P
Portuguese quick reference and English manual
S
Spanish quick reference and Spanish manual
W
Swedish quick reference and English manual
Code
Factory options
Z
Standard product
X
CEQ product
R
Restocked product (if available)
Typical model number: RFT9739R 1 E U F E Z
18
Micro Motion® Model RFT9739 Transmitter
Micro Motion® Model RFT9739 Transmitter
19
©2004, Micro Motion, Inc. All rights reserved. P/N PS-00024, Rev. A
Due to Micro Motion’s commitment to continuous improvement of our products, all specifications are subject to change without notice.
Micro Motion is a registered trademark of Micro Motion, Inc. The Micro Motion and Emerson logos are trademarks of Emerson Electric Co.
All other trademarks are property of their respective owners.
For the latest Micro Motion product specifications, view the
PRODUCTS section of our Web site at www.micromotion.com
Micro Motion Inc. USA
Worldwide Headquarters
7070 Winchester Circle
Boulder, Colorado 80301
T (303) 530-8400
(800) 522-6277
F (303) 530-8459
Micro Motion Europe
Micro Motion Asia
Emerson Process Management
Wiltonstraat 30
3905 KW Veenendaal
The Netherlands
T +31 (0) 318 495 670
F +31 (0) 318 495 689
Emerson Process Management
1 Pandan Crescent
Singapore 128461
Republic of Singapore
T (65) 6777-8211
F (65) 6770-8003
Micro Motion United Kingdom
Micro Motion Japan
Emerson Process Management Limited
Horsfield Way
Bredbury Industrial Estate
Stockport SK6 2SU U.K.
T 0800 966 180
F 0800 966 181
Emerson Process Management
Shinagawa NF Bldg. 5F
1-2-5, Higashi Shinagawa
Shinagawa-ku
Tokyo 140-0002 Japan
T (81) 3 5769-6803
F (81) 3 5769-6843
TM
Micro Motion
Download PDF