Samsung | SCC-B535x(S) | User`s guide | Samsung SCC-B535x(S) User`s guide

User’s Guide
SCC-B5354/B5355(S)
ENG
GER
FRE
SPA
ITA
TUR
B68-00687D_Eng.indd
Digital Color Dome Camera
1
2007-08-06
ソタネト 1:43:0
Safety Precautions
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE REAR
COVER. NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.
This symbol indicates high voltage
is present inside. It is dangerous to
make any kind of contact with any
inside part of this product.
This symbol alerts you that important
literature concerning operation and
maintenance has been included with
this product.
To prevent damage which may result in fire
or electric shock hazard, do not expose this
appliance to rain or moisture.
3.
4.
5.
6.
WARNING
1.
2.
Be sure to use only the standard adapter
that is specified in the specification
sheet. Using any other adapter could
cause fire, electrical shock, or damage
to the product
Incorrectly connecting the power
supply or replacing battery may cause
explosion, fire, electric shock, or damage
to the product.
7.
8.
Do not connect multiple cameras to a single
adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
Securely plug the power cord into the
power receptacle. Insecure connection
may cause fire.
When installing the camera, fasten it
securely and firmly. A falling camera may
cause personal injury.
Do not place conductive objects (e.g.
screwdrivers, coins, metal things, etc.) or
containers filled with water on top of the
camera. Doing so may cause personal
injury due to fire, electric shock, or falling
objects.
Do not install the unit in humid, dusty, or
sooty locations. Doing so may cause fire
or electric shock.
If any unusual smells or smoke come
from the unit, stop using the product. In
such case, immediately disconnect the
power source and contact the service
center. Continued use in such a condition
may cause fire or electric shock.
2
B68-00687D_Eng.indd
2
2007-08-06
ソタネト 1:43:0
If this product fails to operate normally,
contact the nearest service center. Never
disassemble or modify this product
in any way. (SAMSUNG is not liable
for problems caused by unauthorized
modifications or attempted repair.)
10. When cleaning, do not spray water
directly onto parts of the product. Doing
so may cause fire or electric shock.
CAUTION
1.
2.
3.
4.
5.
6.
7.
Do not drop objects on the product or
apply strong shock to it. Keep away from
a location subject to excessive vibration
or magnetic interference.
If you want to relocate the already
installed product, be sure to turn off the
power and then move or reinstall it.
Remove the power plug from the
outlet when then there is a lightning.
Neglecting to do so may cause fire or
damage to the product.
Keep out of direct sunlight and heat
radiation sources. It may cause fire.
Install it in a place with good ventilation.
Avoid aiming the camera directly towards
extremely bright objects such as sun,
as this may damage the CCD image
sensor.
Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases, shall be
placed on the apparatus.
8.
The Mains plug is used as a disconnect
device and shall stay readily operable at
any time
FCC Statement
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful
interference, and
2) This device must accept any interference
received including interference that may
cause undesired operation.
ENG
B68-00687D_Eng.indd
9.
Note
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment
in a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
3
3
2007-08-06
ソタネト 1:43:0
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, or
other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or the
third prong is provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus.
13. Unplug this apparatus. When a cart is
used, use caution when moving the
cart/apparatus combination to avoid
injury from tip-over.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or been dropped.
4
B68-00687D_Eng.indd
4
2007-08-06
ソタネト 1:43:0
Overview ..................................................................................... 6
About this guide ............................................................................6
Product overview...........................................................................6
Main features .................................................................................6
Components...................................................................................6
Checking components in the package .......................................6
Components of your camera ......................................................7
ENG
B68-00687D_Eng.indd
Contents
Installation ................................................................................. 8
Setting switches ............................................................................8
Setting function switches............................................................8
Connecting cables and changing the settings .........................10
Installing camera ......................................................................... 11
Before installation..................................................................... 11
Installation procedure ............................................................... 11
Adjusting the camera direction ..................................................12
Appendix A: Specifications for NTSC Standard ........... 14
Appendix B: Specifications for PAL Standard .............. 15
5
5
2007-08-06
ソタネト 1:43:0
Overview
❚ About this guide
This user guide includes basic instructions for
the product. It is recommended that all users
read this guide before use.
This guide is divided as follows:
 Chapter 1, “Overview,” introduces the user guide
and product related information. (This chapter)
 Chapter 2, “Installation,” explains how to set and
install the product.
 Appendix, “Specifications,” provides the
specifications of the product.
❚ Components
Checking components in the package
Please check your camera and accessories
are included in the package. Those
components are as shown below:
❚ Product overview
This is the high resolution (540 TV lines) dome
camera equipped with a Vari-focal lens, which
has no dynamic delay when implementing
motion pictures, and provides the features
such as digital noise reduction (DNR) by realtime CCD defect compensation, low speed
shutter (LSS: Auto x128) to implement clear
picture quality, Day/Night color compensation,
and the like.
❚ Main features
6
Camera
Test Monitor Cable
Tab screw
User’s Guide
Note
The test monitor cable is used to test the camera
by connecting to a portable display. If you really
want to connect the camera to a monitoring
display, use the BNC cable.
 Power: DC 12V/AC 24V
 Special functions
 Line lock (LL) control
 Auto white balancing
 Horizontal/vertical image reversing
 Flickerless control
 Low shutter speed control
 Backlight compensation control
 Automatic switching between color and black
& white modes
 Equipped with vari-focal lens
 Auto Iris function
 Digital noise reduction (DNR)
 Dynamic CCD defect compensation
B68-00687D_Eng.indd
6
2007-08-06
ソタネト 1:43:0
1
2
3
4
5
6
Lens
@
7 8
9 0
!
#
$
Video connector
Power connector
1. Cover dome: Covers the inner cover, lens, and main
body to protect them.
2. Inner cover: Covers the main body to protect it.
3. Wing locker: Push a long thin screwdriver into its
narrow spot and press it outward when you want to
remove the inner cover.
4. Main body: Includes a lens, a switch board, a PCB
board, screws, and such.
5. Mount bracket: Used as a ceiling or wall fixture. It
is fixed using three long tab screws provided in the
package.
6. Ceiling mount opener: Remove it for line connection
to the ceiling when it is installed on the ceiling.
7. Zoom lever: Using this lever, the lens zoom can be
adjusted and fixed.
8. Focus lever: The lens focus can be adjusted by
rotating it left or right. Rotate it clockwise for fixing.
9. Tilt fixing screw: Using this screw, the slope of the
lens can be adjusted and fixed.
10. Switch board: Includes two kinds of control switches
such as function switches and phase-control switches.
The board has eight function switches in the middle
and two phase-control buttons on each side of the
function switch area.
11. Groove mark: To attach the Main body to the Mount
bracket, align this groove mark on the Main body with
the wide groove in the CAMERA FRONT side on the
Mount bracket.
12. Locker: Used to open or close the Cover dome. To
open the cover dome, press the locker.
13. Lock releaser: Push it outward and rotate the main
body in UNLOCK direction when you want to remove
the Mount bracket from the Main body or to remove
the installed camera from the Mount bracket.
14. Cable: Connect the Video connector to BNC cable
and Power connector to power adapter.
ENG
B68-00687D_Eng.indd
Components of your camera
Your camera has the following components:
7
7
2007-08-06
ソタネト 1:43:1
Installation
❚ Setting switches
Setting function switches
To set the available functions on your camera, adjust eight switches as shown below:
DEC
8
7
6
5
4
3
2
1
INC
No
1
2
3
4
5
6
Name
LL
LSS
H-REV
V-REV
BLC
FL
7
D/N
8
AWB
Brief description
Line lock ON/OFF
Sens-up or Low speed shutter ON/OFF
Horizontal reverse ON/OFF
Vertical reverse ON/OFF
Backlight compensation ON/OFF
Flickerless ON/OFF
Automatic switching between color and
black & white ON/OFF
Automatic white balance ON/OFF
1. Switch 1 (LL): When this switch is set to OFF, the camera operates in the internal
synchronization mode, while when it is set to ON, the camera operates in the line lock mode.
In the internal synchronization mode, the camera always uses an inside crystal oscillator for
synchronization. However if multiple cameras are connected to a sequential switcher, picture
rolling or flickering may occur when switching from one camera to another. In this case, you
can set this switch to ON to solve this problem.
The line lock mode allows the camera to use the phase of the AC power as the
synchronization reference. In this mode, you can use the phase control buttons(INC/DEC).
Note
When you are using the DC 12V power, set this switch to OFF. The line lock feature will not normally
operate even when the switch is set to ON.
Set the LL switch to ON while the AC power is connected. If any picture roll happens, you have
to adjust the phase using the phase-control buttons. Press the INC or DEC button to increase or
decrease the phase by one degree.
8
B68-00687D_Eng.indd
8
2007-08-06
ソタネト 1:43:1
ENG
B68-00687D_Eng.indd
2. Switch 2 (LSS): This sens-up mode accumulates the image fields in memory to reduce
noise but increase the brightness and contrast rate. When this switch is set to ON, the
camera automatically switches to a maximum of 128 times of image acquisition speed to
implement a clear picture for darker image.
3. Switch 3 (H-REV): When this switch is set to ON, the camera image is reversed horizontally.
If you want to monitor your site using a mirror, you can use this feature to see the right
image.
4. Switch 4 (V-REV): When this switch is set to ON, the camera image is reversed vertically.
If your camera reluctantly displays the vertically reversed image, you can use this feature to
see the right image.
5. Switch 5 (BLC): When this switch is set to ON, you can view a clear image even though the
camera faces any excessive light such as sunlight and fluorescent light. When it is set to
OFF, the subject with excessive light is not clearly shown.
6. Switch 6 (FL): When this switch is set to ON, the shutter speed is fixed to 1/100 sec (for
NTSC) or 1/120 sec (for PAL) to prevent screen from flickering by the disaccordance
between vertical synchronous frequency (50Hz for NTSC, 60Hz for PAL) and on-and-off
frequency of a light.
7. Switch 7 (D/N): When this switch is set to ON, the camera automatically switches between
color and B&W according to the brightness of the vicinity.
8. Switch 8 (AWB): This switch adjusts white balancing. When this switch is set to ON, this
camera operates in ATW mode, and in case of OFF, this camera operates in AWC mode.
 ATW (Auto Tracking White Balance): The color temperature is automatically adjusted according to the
environmental change. (Approx. 2000°K to 11,000°K)
 AWC (Auto White Balance Control): It stores the color temperature just when the switch is changed to
OFF. Accordingly color temperatures are adjusted by the stored value.
Caution
-. The IRIS setting range for the camera is approximately 80 to 120 IRE. It means the camera does not
provide the IRIS full open/close feature but the restricted variation range.
-. Use the camera after setting to the proper level (80 IRE or above) because the IRIS hunting may
occur when the level is 75 IRE or below.
9
9
2007-08-06
ソタネト 1:43:2
❚ Connecting cables and changing the settings
Before installing your camera, you have to adjust the lens focus, zoom, and switch settings.
To connect cables
Monitor
BNC Cable
1. Connect the BNC cable
to the Video connector
attached on your camera.
2. Connect the BNC cable
to the Video Input on a
monitor.
3. Connect the power adapter
to the Power connector
attached on your camera.
When the monitor is turned
on, the camera image
appears.
To adjust the lens focus, zoom, and function settings
1. Remove the Cover dome and Inner cover. For more details about the removing procedures,
see “Installation procedure,” in the Installing camera section on the next page.
2. Adjust the focus, zoom, and function settings of your camera using the Focus lever, Zoom
lever, and Switch board while you are viewing the image on the screen.
3. If you want to fix the adjusted focus and zoom, screw up the levers.
10
B68-00687D_Eng.indd
10
2007-08-06
ソタネト 1:43:2
Before installation
Before installing your camera, you have to read the following cautions:
 You have to check whether the location (ceiling or wall) can bear five times the weight of your camera.
 Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it
may cause a breakdown or fire.
 When installing your camera, don’t allow any person to approach the installation site. If you have any
valuable things under the place, move them away.
Installation procedure
To install your camera
1
2
ENG
B68-00687D_Eng.indd
❚ Installing camera
3
4
Ceiling mount
opener
1. Press the Locker button on the bottom of your
camera and remove the Cover dome from the Main
body using the other hand. The Main body and Inner
cover will be exposed to you.
2. To install and adjust your camera, you have to first
remove the Inner cover. To remove the Inner cover
from the Main body, push a long thin screwdriver
into the narrow spot of the Wing locker and press it
outward to remove the cover.
3. Remove the Mount bracket from the Main body by
rotating the Main body in the UNLOCK direction while
pushing the Lock releaser outward. If it is not easily
done, rotate the Mount bracket in the LOCK direction
while holding small holes on the Mount bracket.
4. Fix the Mount bracket to the location (ceiling or wall)
with supplied three screws.
Note
The CAMERA FRONT sign on the Mount bracket
should face the camera monitoring area.
11
11
2007-08-08
ソタネト 6:40:3
5. When you install the Mount bracket on the ceiling, remove the Ceiling mount opener by pressing
it hard to connect the line attached on your camera through the hole in the ceiling. Otherwise, you
can use the empty space opposite to the CAMERA FRONT sign for line connection.
6. Now attach the Main body to the Mount bracket by rotating it in the LOCK direction after aligning
the Groove mark on the Main body with the wide groove around the CAMERA FRONT inlay.
7. Adjust the camera direction. For more details on the direction control, see “Adjusting the camera
direction,” on the same page. When required to adjust the zoom and focus for your camera, see
“Connecting cables and changing the settings,” on page 10.
8. Attach the Inner cover to the Main body by pressing it until a “click” sound is heard after aligning
two screw holes on the Wing lockers of the Inner cover with two screw holes on the Main body’s
left and right sides.
9. Finally attach the Cover dome to the Main body by pressing it until a “click” sound is heard after
aligning the bump inside the Cover dome with the Groove mark on the Main body.
❚ Adjusting the camera direction
When the camera is fixed on the ceiling, you can adjust
the camera viewing angle. You can rotate your camera
leftward or rightward (Panning), and can change the slope
of your camera upward or downward (Tilting).
Panning
In case of panning, the rotation limit of your camera is
set to 355 degree (100 degree clockwise and 255 degree
counterclockwise). The rotation is stopped by the Stopper
inside of the camera. For panning control, first unfasten
Tilting
two screws located on the bottom and rotate in the
direction you want, and then fasten them to fix the camera.
In case of tilting, you can change the slope of your camera
Lens rotation
from zero to 90 degree. However if the slope angle is
under 17 degree, you can encounter a partial image hide
problem. To fix the location after adjusting the tilting angle, use the Tilt fixing screws.
To adjust the focus and zoom of your camera, use the Zoom lever and Focus lever. When
you install the camera on the inclined ceiling or wall, you can rotate the camera lens to see
a correct direction image.
12
B68-00687D_Eng.indd
12
2007-08-06
ソタネト 1:43:2
ENG
B68-00687D_Eng.indd
SCC-B535X
13
13
2007-08-06
ソタネト 1:43:2
Appendix A: Specifications for NTSC Standard
Item
Product type
Power input
Broadcast type
Power consumption
Image device
Pixels
Scanning mode
Scanning line frequency
Synchronization mode
Horizontal resolution
S/N Ratio
Min. object illumination
Signal output
Lens
PAN function
TILT function
Controls
Product color
Operation temperature
Operation humidity
Size
Weight
Details
CCTV color dome camera
AC 24V ± 10% (60Hz ± 0.3 Hz), DC 12V +10%/-5%
NTSC Standard System (525 Lines, 60 Fields)
Approx. 1.7W
1/3 inch IT Type Super-HAD CCD
Total: 811(H) x 508(V), 410,000 pixels
Effective: 768(H) x 494(V), 380,000 pixels
525 Lines, 2:1 Interlace
Horizontal: 15.734Hz(INT)/15.750Hz(LL)
Vertical: 59.94Hz(INT)/60Hz(LL)
INT/Line Lock (Adjusting the phase using INC/DEC button)
540 TV Lines
Approx. 50dB
SCC-B5354 (Color/BW)
SCC-B5355 (Color/BW)
50IRE
0.4/0.04Lux
0.4/0.4Lux
0.24/0.024Lux
0.24/0.24Lux
30IRE
Sens-up Off
0.12/0.012Lux
0.12/0.12Lux
15IRE
F1.2
0.0031/0.00031Lux
0.0031/0.0031Lux
50IRE
Sens-up x128
0,0019/0.00019Lux
0.0019/0.0019Lux
30IRE
15IRE
0.0009/0.00009Lux
0.0009/0.0009Lux
COMPOSITE Video(1.0 Vp-p, 75ohm, BNC), Test Monitor OUT(1.0 Vp-p, 75ohm, Harness cable)
Auto Iris (DC) / Focal length: 2.9 ~ 10.0mm / Aperture ratio: 1.2
Range: 0 to 355° (100 degree clockwise and 255 degree counterclockwise)
Range: 0 to 90°
Line Lock (LL)
Sens-Up; Low Speed Shutter(LSS)
Horizontal Reverse (H-REV)
Vertical Reverse (V-REV)
Backlight compensation (BLC)
Flickerless (FL)
Switching between color and B&W modes (D/N)
Auto white balancing (AWB)
Digital noise reduction (DNR)
Dynamic CCD defect compensation
SCC-B535xN : White / SCC-B535xSN : Dark Silver
-10°C to +50°C
Up to 90%
128(Ø) x 91(H)mm
327g
14
B68-00687C_Eng.indd
16
2007-08-06
ソタネト 4:08:0
Item
Product type
Power input
Broadcast type
Power consumption
Image device
Pixels
Scanning mode
Scanning line frequency
Synchronization mode
Horizontal resolution
S/N Ratio
Min. object illumination
Signal output
Lens
PAN function
TILT function
Controls
Product color
Operation temperature
Operation humidity
Size
Weight
Details
CCTV color dome camera
AC 24V ± 10% (50Hz ± 0.3 Hz), DC 12V +10%/-5%
PAL Standard System (625 Lines, 50 Fields)
Approx. 1.7W
1/3 inch IT Type Super-HAD CCD
Total: 795(H) x 596(V), 470,000 pixels
Effective: 752(H) x 582(V), 440,000 pixels
625 Lines, 2:1 Interlace
Horizontal: 15.625Hz(INT)/15.625Hz(LL)
Vertical: 50Hz(INT)/50Hz(LL)
INT/Line Lock (Adjusting the phase using INC/DEC button)
540 TV Lines
Approx. 50dB
SCC-B5354 (Color/BW)
SCC-B5355 (Color/BW)
50IRE
0.4/0.04Lux
0.4/0.4Lux
0.24/0.024Lux
0.24/0.24Lux
30IRE
Sens-up Off
0.12/0.012Lux
0.12/0.12Lux
15IRE
F1.2
0.0031/0.00031Lux
0.0031/0.0031Lux
50IRE
Sens-up x128
0,0019/0.00019Lux
0.0019/0.0019Lux
30IRE
15IRE
0.0009/0.00009Lux
0.0009/0.0009Lux
COMPOSITE Video(1.0 Vp-p, 75ohm, BNC), Test Monitor OUT(1.0 Vp-p, 75ohm, Harness cable)
Auto Iris (DC) / Focal length: 2.9 ~ 10.0mm / Aperture ratio: 1.2
Range: 0 to 355° (100 degree clockwise and 255 degree counterclockwise)
Range: 0 to 90°
Line Lock (LL)
Sens-Up; Low Speed Shutter(LSS)
Horizontal Reverse (H-REV)
Vertical Reverse (V-REV)
Backlight compensation (BLC)
Flickerless (FL)
Switching between color and B&W modes (D/N)
Auto white balancing (AWB)
Digital noise reduction (DNR)
Dynamic CCD defect compensation
SCC-B535xP : White / SCC-B535xSP : Dark Silver
-10°C to +50°C
Up to 90%
128(Ø) x 91(H)mm
327g
ENG
B68-00687C_Eng.indd
Appendix B: Specifications for PAL Standard
15
17
2007-08-06
ソタネト 4:08:0
B68-00687D_Eng.indd
16
2007-08-06
ソタネト 1:43:2
B68-00687D_Eng.indd
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems)
This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can
take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
17
2007-08-06
ソタネト 1:43:2
B68-00687D_Eng.indd
18
2007-08-06
ソタネト 1:43:2
Download PDF