Blaupunkt | 23/207I-GW-3W-HKDUP | User guide | Blaupunkt 23/207I-GW-3W-HKDUP User guide

LED TV with Freeview & USB PVR
User Guide
Model No
23/207I-GB-3B-HKUP
23/207I-GB-3B-HKDUP
23/207I-GW-3W-HKDUP
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions. All the safety and operating instructions should be read before the
appliance is operated.
Warnings
• To reduce the risk of fire, electric shock or
damage to the television, do not expose it to
dust, rain or moisture, or place any objects filled
with liquids on or near the television.
• Do not place the television in a confined space,
ensure that nothing can obstruct the ventilation
openings at the rear of the television.
To prevent spread of fire,
keep candles or other open
flames away from this
product at all times
• Dispose of this television and any components
including batteries in an environmentally friendly
manner. If in doubt, please contact your local
authority for details of recycling.
Safety
• For your safety, this appliance is fitted with a
fused moulded 3 pin mains plug. Should the
fuse need to be replaced, ensure that any
replacement is of the same amperage and
approved with the BSI mark.
• Never try and replace the mains plug unless
you have adequate qualifications and are
legally authorised to do so. In the event that a
replacement Mains cable is required, contact the
manufacturer for a suitable replacement.
• Never use the television if it is damaged in
any way.
• Always place the television on a flat level surface
avoiding anywhere which may be subject to
strong vibration.
• Ensure the television is not placed on top of the
power cable as the weight of the television may
damage the cable and cause a safety hazard.
• Never place mobile phones, speakers or any
other device which may cause magnetic or radio
interference with the television. If interference
is apparent, move the device causing the
interference away from the television.
• To disconnect the apparatus from the mains,
please use the switch located on the underside/
rear of the TV. The switch shall remain readily
operable.
• When installing on a wall, ensure the TV is at
least 5cm from the wall for ventilation
• Ensure that the power switch on the unit and the
power plug are always easily accessible.
WARNING: Excessive noise when using earphones
and headphones can cause a loss of hearing.
Maintenance
• To clean this unit, wipe with a soft, dry cloth. If
the surfaces are extremely dirty, use a soft cloth
dipped in a soap and water solution or a weak
detergent solution.
• Never use alcohol, paint thinner or benzene to
clean this unit.
• Before using a chemically treated cloth, read the
instructions that came with the cloth carefully.
CAUTION: If water or other liquid enters the
television through the display panel surface, a
malfunction may occur.
Packaging
• The safest way to transport your item is in
the original box/packaging - please save your
packaging for this.
• You will need original box/packaging in the
event of warranty/service repair or support.
We are unable to carry out warranty/service if
you are unable to package it correctly.
4
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:4
6/26/2014 10:07:08 AM
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions. All the safety and operating instructions should be read before the
appliance is operated.
Important Information Regarding Use of
Video Games, Computers, Captions or Other
Fixed Image Displays
The extended use of fixed image program material
can cause a permanent “shadow image” on the
LCD/LED panel.
This background image is viewable on normal
programs in the form of a stationary fixed
image. This type of irreversible LCD/LED panel
deterioration can be limited by observing the
following steps:
1. Reduce the brightness/contrast setting to a
minimum viewing level.
2. Do not display the fixed image for extended
periods of time.
3. Turn the power off when not in actual use.
•
•
•
•
•
Examples of images that you need to watch out
for are as follows (this is not an exhaustive list):
TV Channel Logos: e.g. Shopping channel logos
and pricing displays-especially if they are
bright and stationary. Moving or low-contrast
graphics are less likely to cause ageing of the
screen.
Time Displays
Teletext: Do not view a stationary page for a
long period of time
TV/DVD Menus: e.g. Listings of DVD disc content
Pause Mode: Do not leave the TV in pause mode
for long periods of time, e.g. When watching
DVDs or videos.
How do I dispose of this product?
UK: Waste electrical products should not be
disposed of with household waste. Separate
disposal facilities exist. For your nearest facilities,
please see www.recycle-more.co.uk or in store for
details.
ROI: Waste electrical products should not be
disposed of with household waste. Separate
disposal facilities exist. Check with your Local
Authority or retailer for recycling advice.
Batteries
• Do not expose batteries to high
temperatures, excessive heat,
prolonged sunshine or fire
as this may cause leakage,
explosion or ignition.
• Observe the correct polarity when
inserting batteries.
• Do not use different types of
batteries together or mix old and
new batteries.
• Dispose of batteries in an
environmentally friendly way.
• Certain regions may regulate the
disposal of batteries.
Please consult your local authority.
Cd
Important - Once ‘shadow image/screen burn’
occurs, it will never disappear and is not repairable
under warranty.
5
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:5
6/26/2014 10:07:08 AM
CONTENTS
Manufacturers Guarantee Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
What is included in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Attaching the stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Detaching the stand/ Securing the TV to a wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
TV Buttons and Input Source Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
TV Menu Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-25
Channel Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Picture Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Sound Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Time Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
System/Hotel Lock Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7 Day TV Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
USB Record - Digital / Freeview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
USB Mode / Media Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-34
Using your TV with a Sky digital set top box . . . . . . . . . . . . . . . . . . . . . . . . 31
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-33
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:7
6/26/2014 10:07:08 AM
What is included in the box
WHAT IS INCLUDED IN THE BOX
Accessories
Included with this TV are the following accessories
1 x User Guide
1 x Remote Control
User Guide
2 x AAA Batteries
1 x Quick Start Guide
Quick Start
Guide
1 x TV
1 x Stand plus screws
1 x RF Cable
Please save your packaging as you will need this in the event of warranty/service repair or support. We
are unable to carry out warranty/service if you are unable to package it correctly. The safest way to
package your item in the event of warranty/service repair is in it’s original box/packaging.
8
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:8
6/26/2014 10:07:09 AM
Attaching the stand
ATTACHING THE STAND
Attaching the stand
To complete the stand installation you will require a cross head screw driver
Screws that are included.
3 x M (4x12)
4 x ST (4x12)
Used for attaching the stand neck
to the TV (fig.1)
Used for attaching the stand base
to the stand neck (fig.3)
3x
M (4x12)
(fig.1) Attach the stand neck to the rear of the TV set
using the 3 x M(4x12) screws provided.
1
1
1/2
(fig.2) Peel off the protective plastic cover then attach
the stand base to the stand neck.
2
4 x ST (4x12)
3
When securing the self-tapping screws into the base of the stand (on first
installation) the screws will be naturally tight as they are creating a thread
in the plastic of the stand neck in order to support a TV of this size.
a) Ensure the cross head screw driver tip fits correctly into the head of the
screw and that it is not too big or small.
b) Screw in all screws individually and partially before tightening all of the
screws individually and partially until they are fully inserted.
c) If they become very tight try loosening them slightly and then retightening them once again as this will continue the process of creating the
thread for the screws.
(fig.3) Secure the base to the neck by using the
4 x ST (4x12) screws provided.
9
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:9
6/26/2014 10:07:13 AM
Detaching the Stand / Securing the TV to a Wall
DETACHING THE STAND
Detaching the stand
Remove the screws highlighted then remove the stand base and neck from the rear of the TV set.
Securing the TV to a Wall
For maximum security in the home when using a TV with its stand anti-tip straps should be fitted. These
are available from supermarket websites and other websites and are an easy, inexpensive and effective
way of ensuring your TV stays safely upright. Straps are designed to be attached to the rear of the TV
and then tethered to the wall of the furniture the TV is stood on, if wood. (The 2 images should appear
underneath this text).
Note - Please ensure that children do not climb on the TV set.
A) Using one or both of the top wall-mounting
holes and screws (the screws are already supplied
in the wall mounting holes) fasten one end of the
fastening cord/s to the TV.
B) Secure the other end of the fastening cord/s to
your wall. (you will need screws/fixings suitable
for your wall type - available separately from most
DIY stores).
The Royal Society for the Prevention of Accidents is urging people to take care with flat-screen televisions.
RoSPA stated in 2010 that “Toddlers are particularly at risk of pulling flat-screen televisions on to
themselves. They are unsteady on their feet and are attracted by colourful television images.”
The risk is increased as televisions become lighter.
10
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:10
6/26/2014 10:07:15 AM
Wall mounting
WALL MOUNTING
Wall mounting the TV
IMPORTANT - Before drilling any holes in the wall ensure you are not drilling
where there could be any electric wires, water or gas pipes.
1) Remove the four screws highlighted that are supplied in the wall
mounting holes.
2) The wall mount can now be easily attached to the mounting holes on
the rear of the TV.
For optimum viewing, if wall mounting the TV higher than eye level, the TV should be tilted downwards
so that the TV’s screen is ‘face on’. See fig 1 and 2.
For VESA wall mounting information please refer to the Technical Specification page.
Important – If wall mounting this TV, only use the screws already provided in the wall mounting holes.
Using other screws which are longer could cause irreparable damage to internal parts.
fig 1
INCORRECT
TV
Viewing angle
fig 2
CORRECT
TV
Viewing angle
11
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:11
6/26/2014 10:07:15 AM
TV BUTTONS & SOURCE MENU
This information is for models
This information is for models
without built in DVD players
with built in DVD players
1
2
1
3
2
4
3
5
4
6
5
7
6
8
7
9
1 Volume up and menu right
1 Stop/Eject Disc
2 Volume down and menu left
2 Play/Pause Disc
3 Programme/Channel up and menu up
3 Volume up and menu right
4 Programme/Channel down and menu down
4 Volume down and menu left
5 Displays Menu/OSD
5 Programme/Channel up and menu up
6 Displays the input source menu
6 Programme/Channel down and menu down
7 Standby Power On/Off
7 Displays Menu/OSD
8 Displays the input source menu
9 Standby Power On/Off
Choosing Mode Input/Source
To switch between the different input/
connections.
A) Using the buttons on the remote control:
1) Press [SOURCE] - The source menu will appear.
2) Press [\/] or [/\] to select the input you require.
3) Press [OK].
B) Using the buttons on the Television:
1) Press [SOURCE].
2) Scroll up / down using CH+/ CH- buttons to
the input/source you require.
3) Press Vol+ to change input/source to the
one selected.
Example of Source menu
depending on the TV model
12
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:12
6/26/2014 10:07:16 AM
Remote Control
REMOTE CONTROL
1
STANDBY - Switch on TV when in standby or vice versa
MUTE - Mute the sound or vice versa
DTV - Switch to Freeview source
RADIO - Switch to radio whilst in Freeview source
USB - Switch to USB source
DVD - Switch to DVD source
2
NUMBER BUTTONS - 0 – 9 to select a TV channel directly.
TV GUIDE - Opens the 7 Day TV Guide (Freeview mode)
- To return to the previous channel viewed
3
4
VOL (+/-) - To increase / decrease the sound level
P.MODE - Scrolls through picture mode options
S.MODE - Scrolls through sound mode options
FAV - To display favourites menu
CH (+/-) - To increase or decrease the channel being watched
MENU - To display OSD menu
EXIT - To exit all menus
- Allows you to navigate the on-screen menus
and adjust the system settings to your preference
SOURCE - To display the input/source menu
INFO - Press once for now/next channel information
Press twice for programme information about current
programme
ASPECT - To switch the screen between the different picture
formats
SLEEP - Press repeatedly to cycle through the sleep options
AUDIO - To change the audio language (if available)
SUBTITLE - To switch the dialogue at the bottom of the screen
(on/off)
TEXT - To enter/exit Teletext (Analogue TV)
TEXT HOLD - Teletext mode - Hold current page which is
displayed (Analogue TV)
DISPLAY - To switch off the screen when listening to radio
TEXT/DVD ZOOM - Zoom function for Teletext and DVD
DVD MENU/RECORD - Access the DVD root menu and USB
record function
- To restart the current chapter
- To advance forward to the next chapter
- To stop the playback/Eject Disc
(To EJECT the disc press/hold the
button for 4 seconds)
1
2
3
4
- To play in fast rewind mode
- To play in fast forward mode
- To play/pause
DVD SETUP/REC LIST - Opens up DVD Menu or Opens the list
of what has been previously recorded
GOTO - To go to a specific chapter
A-B - Press once to set point, press a second time to return
to point
ANGLE - Select different angle of DVD
REPEAT - To repeat playback
For Models with Integrated DVD players
For Models with PVR Function
For Models with USB Playback
13
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:13
6/26/2014 10:07:30 AM
Connections
CONNECTIONS
V IDE O
A
C
B
US B
G
L
R
Y
E
D
C I C A R D IN
E A R P HO NE
I
J
H
A
SCART
SCART input
B
HDMI 1
HDMI input
C
Video
Component / Video input
D
R/L
R/L Audio shared for
Video/Composite and
component/ YPbPr
E
YPbPr
HD input (Ypbpr)
Pb
F
RF IN
RF / TV Aerial Input
G
USB
USB port
H
HDMI 2
HDMI input
I
CI CARD IN
Common Interface module
J
EARPHONE
Earphone socket
Pr
F
15
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:15
6/26/2014 10:07:31 AM
Connections
CONNECTIONS
Note: Connecting cables are shown for example only and may not be included. Please check ‘What Is
Included In The Box’ page.
Connecting to a device with Composite AV/Video output
TV Source should be set to Video
L (white)
L (white)
R (red)
R (red)
Video
(Yellow)
Video
(Yellow)
Connecting to a device with SCART output
TV Source should be set to SCART
SCART
SCART
Connecting to a device with HDMI output
A HDMI cable can output both video and audio and enables you to enjoy digital-quality video and audio
with minimal loss of quality.
TV Source should be set to the corresponding HDMI port (HDMI 1, HDMI 2 etc)
Note: This model TV can not be used as a PC/laptop monitor via the HDMI input. The HDMI Input is
provided to view digital content with compatible external devices
16
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:16
6/26/2014 10:07:32 AM
Connections
CONNECTIONS
Connecting to a device with Component/YPbPr output
If you are supplied with a cable from the device which has RED, GREEN, BLUE, RED & WHITE connectors
you must connect via Component (for picture) and by phono cable (for sound).
TV Source should be set to Component.
Y
Y
PB
PB
PR
PR
L
L
Audio
R
R
Connecting to an external audio device (Amplifiers, Surround Sound,
Sound Bars etc)
When connecting via the TV’s 3.5mm Earphone output, this will disable the TV speakers.
3.5mm
EARPHONE
3.5mm
AUDIO
IN
17
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:17
6/26/2014 10:07:32 AM
TV Menu Operation
CHANNEL MENU
To access this menu, press [MENU] button on the remote control.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Auto Tuning - Allows you to retune the television for all digital channels, digital radio stations and
analogue channels
Analogue Manual Tuning - Allows you to manually tune your analogue signal
Freeview Manual Tuning - Allows you to manually tune your digital signal
Channel Edit - Allows you to delete, move, skip and add favourite channels
Schedule List - Lists your programme reminders
Signal Information - Allows you to view signal frequency, signal quality and signal strength
CI Information - Pay per view services require a “smartcard” to be inserted into the TV. If you subscribe to
a pay per view service the provider will issue you with a ‘CAM’ and a “smartcard”. The CAM can then be
inserted into the COMMON INTERFACE PORT (CI Card In)
Tip: If you do not press any buttons for 30 seconds, the menu will automatically exit. You can change
the length of time before the menu exits automatically - see ‘Menu Duration’ in the Setup Menu
19
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:19
6/26/2014 10:07:32 AM
TV Menu Operation
PICTURE MENU
Economy
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Picture Mode - Choose from the following presets:
Dynamic
Recommended settings for fast moving pictures
Standard
Standard settings
Mild
Set to be lighter in colour and less bright
Personal
Lets you manually alter all the settings
Economy
Power saving mode which reduces the energy used by up to
25% (by reducing the power to the LED/LCD panel).
In Economy mode, the TV will switch itself to Standby mode
after 3-5 hours in the event that the TV buttons or remote
control buttons are not pressed (change the picture mode
to another setting to de-activate this function)
You can make the following adjustments in Personal mode:
Contrast - Switch the balance between black and white.
Brightness - Increase or decrease the brightness of the picture.
Colour - Increases the colour from black and white.
Tint - Lets you increase or decrease the level of tint within the picture
(only available in VGA/PC source mode).
Sharpness - Increase or decrease the sharpness of the picture.
Colour Temperature Choose from the following presets:
Normal
Default settings
Warm
Increases red within the picture
Cold
Increases blue within the picture
Noise Reduction - Choose from the following presets:
Off
Turns noise reduction off
Low
Minor system adjustment
Middle
Medium system adjustments
High
Maximum system adjustments
20
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:20
6/26/2014 10:07:32 AM
TV Menu Operation
SOUND MENU
Audio Description
Off
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Sound Mode - Choose from the following presets
Standard
Default settings
Music
Emphasises music over voices
Movie
Provides live and full sound for movies
Sports
Emphasises sound for sports
Personal
Selects your personal sound settings
Tip: Treble and bass levels can only be
adjusted when the sound mode ‘Personal’
is selected.
Treble - To adjust the amount of high frequency within the sound
Bass - To adjust the amount of low frequency within the sound
Balance - To switch the sound between the left and right speakers
Auto Volume Level (AVL) - When ‘on’ is selected, the volume will attempt to stay at a constant level
regardless of TV programme and advertisements
Audio Description - This allows the user to turn Audio Description on or off (Audio Description is a service
available on certain programmes. It provides a description of what is happening during the selected
programme for a person who is visually impaired)
21
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:21
6/26/2014 10:07:33 AM
TV Menu Operation
TIME MENU
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Clock - Shows the date and time
Off Time - Allows you to set a specific time for your TV to turn off
On Time - Allows you to set a specific time for your TV to turn on, the channel it will then display, the
source it will be on and also the volume. This function can then be toggled to repeat every day or a
certain day (the TV must be in standby mode for this to be effective)
Time Zone - Change your current time zone
Sleep Timer - Lets you set the sleep timer so the television automatically switches off after a set amount of
time. Off -> 10min -> 20min -> 30min -> 60min -> 90min -> 120min -> 180min -> 240min
Auto standby - Set Auto standby between 3 hours, 4 hours and 5 hours ( to turn off this function you must
exit Home Mode in the Picture Menu)
OSD Timer - Lets you adjust the amount of time the On Screen Menu stays on the screen before
disappearing
22
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:22
6/26/2014 10:07:33 AM
TV Menu Operation
SYSTEM/HOTEL LOCK MENU
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
System/Hotel Lock - Allows you to lock or unlock the menu. You will be asked to enter a 4 digit password
Use the ◄ button to quit the password input or use the ► button to clear. Default password is 0000.
TV Button Lock - Allows you to lock the buttons on the side of the TV set
Parental Guidance - Allows you to set the rating to block certain content based on age information
Default Source - Allows the user to set the default source. The default source is the source the TV starts on
when first switched on
Default Channel - Allows the user to set a channel as the default channel on the Digital source. The
default channel is the channel the TV starts on when first switched on
Source Lock - Allows you to lock the source menu
Channel Lock - Allows you to lock certain channels manually
Max Volume - Allows you to adjust and set the maximum volume
Change Password - Allows you to change the password
23
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:23
6/26/2014 10:07:33 AM
TV Menu Operation
SETUP MENU
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Language - Allows you to change the language of the menu
TT Language - Allows you to change the Teletext language
Audio Language - Shows the current audio language
Subtitle Language - Shows the current subtitle language
Hearing Impaired - This allows the user to turn on the Hearing Impaired function, this produces subtitles
on the screen which provide a description of what is happening during the selected program.
PVR File System - Allows you to view the format and performance of a USB key
Aspect Ratio - Within the UK the picture format varies depending on the channel/broadcast. There are a
number of different options to best meet your needs
Auto
4:3
Displays the 4:3
picture in its
original size.
Side bars are
shown to fill the
16:9 screen
16:9
Fills the screen
with a regular
16:9 signal and
4:3 picture
format will be
stretched to fill
the screen
Stretch
Displays the
14:9 picture
in the correct
proportion. As
a result side
bars are shown
on the screen
Automatically displays the best picture format. So the
picture is in the correct position. May have black lines
at the top/bottom and/or sides.
Original
Will display the picture from the broadcaster
without any change
Zoom
The picture
is the correct
proportion
but zoomed
in to fill the
screen
24
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:24
6/26/2014 10:07:33 AM
TV Menu Operation
SETUP MENU
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Blue Screen - Changes the background when there is no input between clear and a blue background (Only
available on some sources)
First Time Installation - Allows you to retune the television for all digital channels, digital radio stations
and analogue channels
Reset TV - This resets the menus to factory settings and will erase all TV channels stored on the television
Software Update (USB) - This menu lets you install the new software/firmware onto the television. Further
details of how to do this will be issued with the firmware. Contact the helpline or refer to the ‘product
support’ section of the website
HDMI CEC (Consumer Electronic Control) - Allows HDMI devices to control each other and allows the user
to operate multiple devices with one remote control. (only available with compatible devices)
25
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:25
6/26/2014 10:07:34 AM
DVD Menu Operation
DVD SETUP
(Applies to models with built in DVD player)
To enter this menu please ensure the TV is in DVD source & press [DVD SETUP]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [DVD SETUP] button.
TV Display - Choose from the following options
4:3 Pan scan
PS Traditional picture format, often used on old film
4:3 Letter box
LB Traditional picture which has been adapted for widescreen
Wide
16:9 Widescreen picture format
Speaker Setup - Choose from the following options
LT/RT
Converts from multi-channel sound to mono
Stereo
Converts from multi-channel sound to stereo
Dual Mono - Choose from the following options
Stereo
Outputs 2 channels of sound both left and right
Mono L
Outputs left side sound
Mono R
Outputs right side sound
Mix Mono
Outputs a single channel of sound but mix between right and left
Dynamic Range - This is the difference between the quietest and loudest sounds. This setting works only
with DVD discs recorded in Dolby digital.
Full
Set this to listen with the range recorded on the disc
3/4
Set this to listen with a range equivalent to a normal television
1/2
Set this to listen with a smaller difference between the maximum and minimum volume
1/4
Set this to listen with a smaller difference between the maximum and minimum volume
Off
Set dynamic range to off
TV Type - Choose from the following options
PAL
For discs from UK/Europe, Asia, Australia etc
Multi
For both NTSC and PAL
NTSC
For discs from North America, Japan etc
Default - Choose from the following options
Reset
Resets all options in the ‘DVD setup’ menu back to the default settings
Tip: This TV/DVD player is pre-set to play Region 2 DVDs. In the event you wish to use the TV/DVD in
another country that uses different region discs, please visit www.umc-uk.co.uk. Select ‘Product Support’,
‘Changing Region’.
27
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:27
6/26/2014 10:07:34 AM
7 Day TV Guide
7 DAY TV GUIDE
TV Guide is available in Freeview TV mode. It provides information about forthcoming programmes
(where supported by the Freeview channel). You can view the start and end time of
all programmes and on all channels for the next 7 days and set reminders.
1) Press [TV GUIDE]. The following 7 Day TV Guide will appear..
EXIT
2) Navigate through the menu using
You can now:
Record a programme by pressing RED (USB device must be connected)
Set a reminder by pressing GREEN
View a previous day by pressing YELLOW
View the next day by pressing BLUE
3) Press [EXIT] to exit the 7 day TV Guide.
28
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:28
6/26/2014 10:07:34 AM
USB Record
USB RECORD - DIGITAL/FREEVIEW MODE
USB RECORD – DIGITAL/FREEVIEW MODE
Built into this television is a USB record facility. This function is available in Digital/Freeview mode when
used in conjunction with a compatible USB memory stick or USB hard drive. The benefits of this are as
follows:
• Pause live TV and then playback, fast forward and rewind (up to live TV)
• One button record, if you decide you want to record the current programme
• Easy programmable recording from the 7 day TV Guide
• Record TV and watch/listen back on your computer/laptop
Due to the nature of the product, it is necessary to use a high speed USB memory stick (as the TV reads
from and writes to the memory stick at the same time, some memory sticks may not be suitable)
You can purchase high speed memory sticks from some computer stores, alternatively, we have a selection
of tested and compatible memory sticks available to purchase directly from the helpline/web site.
Minimum Specification - USB Memory Stick
Read Speed
20 MB/s (Mega Byte Per Second)
Write Speed
6 MB/s (Mega Byte Per Second)
If you wish to use a USB portable hard drive larger than 32GB, please refer to the FAQ section at the rear
of this user guide.
Pause Live TV (Time Shift)
Pausing Live TV is very simple.
- Press the play/pause button and the television will pause and the live
content will be recorded. To resume watching press play/pause again.
- Press fast forward to go forward in a recording (i.e. to skip adverts)
- Press fast rewind to go back in a recording (i.e. if you fast forwarded
too far)
Tip: When you switch the TV to standby or change channel the Time Shift memory is wiped. To restart
time shift you must press play/pause button.
One Button Record
At any point in time you may decide to record the current channel that you are watching. To do this you
need to press the red button highlighted below.
Tip: This television contains one TV tuner, therefore it can only record the channel you are watching or
record one channel while the television is in standby mode.
Note: USB record function is only avilable in Digital/Freeview TV mode. Due to copyright laws and
illegal copying/recording it is not possible to record to/from any other input/output source.
29
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:29
6/26/2014 10:07:34 AM
USB Mode / Media Player
USB MODE/MEDIA PLAYER
USB mode offers playback of various different types of content that you have saved on your USB
Memory Stick.
On switching to USB source the above menu screen will appear. The content will be divided into Photo,
Music, Movie and Text based on file type.
1) You can navigate through the menus using the
buttons. To confirm the item you
scroll
wish to play/view press [OK] button.
2) Select the drive you require. (If your drive only
has 1 partition you will only see 1 item).
3) You can now access the item. Press OK to view.
4) While viewing you control the item using
and (OK)
or by pressing ( i ) and using
Tip: If you experience a playback issue, please ensure the files being used are the correct format
(example - the picture plays but no sound) See technical specification page for compatible file types
30
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:30
6/26/2014 10:07:35 AM
General Information
USING YOUR TV WITH A SKY DIGITAL SET TOP BOX
Option 1) Connecting your TV to your Sky box (when both the TV and Sky Box are located
in the same room)
Depending on your Sky Box & TV model, connect either by SCART or HDMI cables
(available separately)
If connecting by SCART, select the ‘Input source’ on the TV as SCART.
If connecting by HDMI, select the ‘Input source’ on the TV as HDMI (if the TV has more
than 1 HDMI port, ensure you select the input source to match the HDMI numbered port
on the rear of the TV)
If you wish to use your Sky remote to operate the TV’s functions, you will need a Sky
remote control (Revision 9 or later) and you will need to programme a 4 digit code into it.
See bottom of this page.
SCART
or HDMI
cable
Sky Box
Option 2) Connecting your TV to your Sky box (when your Sky box is located in a different
room to the TV)
Please note, if you are adding a ‘Magic
Eye/TV Link’ to your system so that
you can use your Sky remote control
to change the Sky channel in the room
where the 2nd TV is located, please
refer to the instructions included
with the TV link/magic eye in order to
ensure the RF or RF2 output on your
Sky box is powered on. (The red LED
light on the TV link/magic eye will light
up if the RF / RF2 output is correctly set
up) If you do not have the instructions
that came with the TV link/magic eye,
instructions on how to do it can be
found on our web site.
2nd TV in
another room
Connect to the
Aerial/RF input
on the 2nd TV
SCART
or HDMI
cable
RF/COAX cable from
Sky Box to 2nd TV
Sky Box
Connect to RF
or RF2 output
on the Sky box
TV Link/Magic Eye
(optional)
1) To tune the TV to the Sky box, on the 2nd TV, select the ‘Analogue’ input source.
2) Select the channel that you wish to store the Sky box/channel on. (If you do not use channels 1-5 because you
no longer have analogue terrestrial channels after digital switchover, you may choose to select channel 1 to store
the Sky box/channel, if you still have and use analogue channels 1-5, you may for example decide that channel 6 is
the best option for you)
3) Press the corresponding number on the remote control to select the desired analogue channel chosen as per
point 2 above.
4) On the TV remote control, press Menu. Now navigate through the menus to select Manual Tuning or Analogue
Manual tuning (refer to the Tuning/Channel menu section of this user guide if necessary)
5) Manually tune in the channel (usually, the Sky box is at a frequency between 800Mhz and 850Mhz) once the
Sky box/channel is found, press ‘OK’ to store it.
If you wish to use your Sky remote to operate the TV’s functions, you will need a Sky remote control (Revision 9 or
later) and you will need to programme a 4 digit code into it. See below.
Using a Sky Remote or a Universal Remote to operate your TV
Sky Remote Control - If you wish to use your Sky remote to operate the basic functions of your TV, you need to
programme a 4 digit code into it. Please note - you will need the latest Sky Revision 9 remote control as this is
the only version that includes the latest software/firmware necessary to operate this model of TV.
The code required for this television is 2134. If you wish to upgrade/replace your existing Sky remote control to
the latest version, you can do so on our web site.
Universal Remote Control - If you wish to use a Universal remote control to operate your TV, please refer to the
website for a full list of codes. (Please note we only have codes for One for All branded remote controls, if you
have an alternative brand of Universal remote, please refer to the manufacturer for the code.)
31
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:31
6/26/2014 10:07:36 AM
General Information
FREQUENTLY ASKED QUESTIONS
General
I would like to have louder
sound by connecting
additional speakers
1) Use the 3.5mm headphone output and a 3.5mm to phono cable
(available separately) to connect to an amplifier/surround sound system.
Please note this will deactivate the TV’s built in speakers.
2) Connect a COAX cable from the TV’s COAX output to your
amplifier/surround systems COAX input.
General
Why are some options in
the menu unavailable and
greyed out
Some options are only available in certain sources, i.e. HDMI. They are
unavailable in the other sources where they have no affect.
General
Can I stop my TV automatically
turning off after 4hrs?
Yes, in the time settings menu, scroll down to Auto standby and select
OFF.
TV
I have tuned in Digital TV
but I am not receiving any
or all of the channels and/
or the channels I receive are
breaking up
1) Check you are in an area that can receive Freeview/Saorview
Visit www.freeview.co.uk or www.saorview.ie
2) Check you are using an aerial that is able to receive a good digital
signal. In most cases, you will need an outdoor digital hi-gain/wideband
aerial. In areas that have excellent digital coverage, you may be able
to use a loft type aerial but it is highly likely that you will also need to
connect a booster between the back of the TV and the TV aerial wall
socket. Unfortunately, to receive a good enough digital signal, it is not
possible to use a portable/indoor type aerial.
TV
I have re-tuned my television
but when I switch it off it is
not storing the channels
Complete a first time installation, please refer to the set-up menu section
of the manual of how to do this.
DVD
I have inserted a disc but it is
not playing
1) Ensure you have inserted the disc facing the correct way.
2) Ensure the disc is clean and is not scratched.
3) Some copied discs will not play.
4) Check the DVD is a region 2 disc – to change the region of the DVD
player, refer to www.umc-uk.co.uk select ‘product support’, ‘changing
region’.
DVD
I have pressed the eject
button but the disc is not
coming out
To eject the disc hold the stop/eject button for 4 seconds.
VCR/DVD
Recorder
I have connected the TV to
my VCR or DVD Recorder via
SCART but it is not recording
In addition to connecting via SCART, you should connect the aerial cable
from the wall socket to your VCR/DVD Recorder and another aerial cable
from the VCR/DVD Recorder to the TV.
Game Consoles
I have connected my PS3 to
the TV via HDMI, but I am
not receiving any pictures or
sound on my Television
1) Ensure the TVs source is on HDMI.
2) Check your settings on your PS3 are as per the PS3 instruction manual.
Game Consoles
I have connected my
Xbox 360 to the TV via
Component Cables (Red,
Green & Blue) but I am not
receiving any sound
Component cables only provide HD Pictures. For the sound you will need
to connect the Red & White audio cables on the Xbox to the Red & White
phono inputs on the rear of the TV. Please refer to the ‘Connections’
pages.
System Lock
I have changed the password
on the television and now
forgotten it
There is a master password of 4711, to gain access to the TV menu and
reset the normal password.
32
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:32
6/26/2014 10:07:36 AM
General Information
FREQUENTLY ASKED QUESTIONS
USB Mode
I have inserted a USB
Memory Key, but the TV
does not recognise it
Ensure the USB Memory Key is formatted to type FAT32.
USB Mode
Using a USB portable hard
drive / larger than 32GB
If you wish to use a portable hard drive larger than 32GB, please note
that it must be formatted to the FAT32 file system in order to operate on
this TV. Windows XP/Vista computers are only capable of formatting up
to 32GB, therefore, you will need a software programme/utility to format
larger hard drives. Please refer to the web site for more information.
USB Record /
TV models only
I cannot change the channel,
access the menu or use the
red button
During Time Shift you cannot change the channel, access the menu or use
the red button
USB Record /
TV models only
When using the USB to
record the picture ‘breaks
up’ or experience loss of
sound.
Check the USB Memory Stick meet the minimum requirements of Read
Speed - 20 MB/s (Mega Byte Per Second), Write Speed - 6 MB/s (Mega Byte
Per Second)
33
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:33
6/26/2014 10:07:36 AM
TECHNICAL SPECIFICATION
Model
23” Model
23” models with inbuilt DVD player
23/207I-GB-3B-HKUP
23/207I-GB-3B-HKDUP
23/207I-GW-3W-HKDUP
Screen size
(diagonal)
23”/58cm
Resolution
1366 x 768
RF
75 ohm Antenna / Analog / DVB
Inputs
2 x HDMI, 1 x USB, 1 x SCART,
1 x Component/Y Pb Pr, 1 x Composite/Video,
1 x shared audio for Composite/Video & Component/YPbPr
Sound Outputs
1 x 3.5mm Headphone
Sound power,
watts (RMS)
2x3
Voltage and power
consumption
110 - 240V ~ 50/60Hz
20/40W
(home/max)
(<0,5W inStandBy)
(0W in OFF mode)
110 - 240V ~ 50/60Hz
20/50W
(home/max)
(<0,5W inStandBy)
(0W in OFF mode)
Annual Energy
Consumption
29 kWh
Energy Rating (EEI)
A
A
Dimensions including
stand (mm)
548W x 379H x 140D
Net weight (Kgs)
3.4
3.6
Wall Mounting
VESA 100 x 100
Compatible files in USB Mode
Media
File Ext.
Codec
Video
Movie
Music
Picture
Audio
.mpg
Mpeg-1, Mpeg-2
.avi
Xvid, MJPEG,
MPEG-4 SP/ASP
.ts
Mpeg-2
.dat
Mpeg-1
.mp4
Mpeg-1, Mpeg-2
.vob
Mpeg-2
Max Resolution: 1920x1080
Max Data rate: 40Mbps
MP3, WMA
Max Resolution: 1920x1080
Max Data rate: 40Mbps
Max Resolution: 1024x768
Max Data rate: 40Mbps
.mp3
-
MP3
.wma
-
WMA
Sample Rate 16K-48KHz
Bit rate: 32K - 442Kbps
.jpg
Progressive JPEG
Max Resolution: 1024x768
.jpeg
Baseline JPEG
Max Resolution: 8192x8192
.bmp
BMP
Max Resolution: 6500x6500
34
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:34
6/26/2014 10:07:36 AM
User Guide - Blaupunkt - 23-207 - BLA-MAN-0216.indd Sec1:36
6/26/2014 10:07:36 AM
Download PDF