GTDP220GF GE 7.0 cu. ft. capacity Dura Drum gas dryer

GTDP220GF GE 7.0 cu. ft. capacity Dura Drum gas dryer
GTDP220GF
GE® 7.0 cu. ft. capacity Dura Drum gas dryer
Dimensions and Installation Information (in inches)
Special Installation Requirements
Exhaust Option: When viewed from the front
of the unit, exhaust 3-way via rear, left and
bottom. Dryer is shipped exhausted to the
rear. Alternate exhausting knockouts are
supplied.
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side; 3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
• Closet doors must be louvered or otherwise ventilated and must contain a minimum
of 60 sq. in. of open area equally distributed. If this closet contains both a washer and
a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Gas: An individual, properly-grounded
branch circuit, with a three-prong groundingtype receptacle, protected by a 15 or 20
amp circuit breaker or a time-delay fuse is
required.
Gas Dryer Electric Rating: 120V, 60Hz, 6A
Gas (BTU/HR): 22,000. Factory-equipped for
natural gas. Tested for LP gas. LP gas supply
requires a conversion kit. Check installation
instructions for correct kit and have a
qualified gas technician install a conversion
kit. See dryer ducting information for proper
installation.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes,
with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces are: 0" both sides; 3" rear
Dryer Exhausting Information­: Use metal duct only, vertical and horizontal ducting.
Note: Dryer wall outlet must be located within
36" of service cord entry and accessible when
dryer is mounted in position.
Installation Information: For complete
information, see installation instructions
packed with your dryer.
For answers to your Monogram,® Cafe™ Series,
Profile™ Series or GE® appliance questions, visit
our website at geappliances.com or call
GE Answer Center® service, 800.626.2000.
Specification Revised 4/15
Rear View
Side View
GTDP220GF
GE® 7.0 cu. ft. capacity Dura Drum gas dryer
5.7 cu. ft. Dryers
Dimensions and Installation Information (in inches)
23-1/2
28-1/4
5
2 side panel to the front.
*24-1/2" from the edge of the
25-1/2" from front to edge of endcaps.
25-1/2*
27
30-1/2
8-1/2
5.8,
6.0 Cord
andLocations
7.0 cu. ft. Dryers
Power
36
42
Power
Cord Hole
4-1/2
11-1/2
Back View
2-1/2
Side View
Power
Cord Hole
2
Back View
3-1/2
Rear View
Washer/Dryers SC QSart
For answers to your Monogram,® Cafe™ Series,
Profile™ Series or GE® appliance questions, visit
our website at geappliances.com or call
GE Answer Center® service, 800.626.2000.
Specification Revised 4/15
GTDP220GF
GE® 7.0 cu. ft. capacity Dura Drum gas dryer
Dryer exhausting information—use metal
duct only vertical and horizontal ducting
Best performance
Maximum length
of 4" dia rigid
A 4
metal duct
B
A
Exhaust hood type
Number
A
B
4
2-1/2
of 90°
4"
2-1/2"
B
turns opening opening
Domestic dryer models
0
200 ft.
175 ft.
2-1/2
1
185 ft.
165 ft.
2
175 ft.
155 ft.
3
165 ft.
145 ft.
GE Frontload Long Vent 7.0
4
155 ft.
135 ft.
cu. ft. capacity electric dryer
(GFDL)
5
145 ft.
125 ft.
0
150 ft.
125 ft.
1
135 ft.
115 ft.
2
125 ft.
105 ft.
3
115 ft.
95 ft.
Long Vent 6.0 - 8.0 cu. ft.
4
105 ft.
85 ft.
capacity electric & gas dryers
(GTDL and GTV)
5
95 ft.
75 ft.
0
120 ft.
90 ft.
1
100 ft.
75 ft.
2
85 ft.
65 ft.
3
70 ft.
55 ft.
Long Vent 7.0 cu. ft. capacity
4
60
ft.
45
ft.
electric & gas (GTD42, GTD45,
GTD65, GTX42 and GTX60)
5
55 ft.
35 ft.
0
90 ft.
60 ft.
All 6.0 - 8.3 cu. ft. capacity
1
60 ft.
45 ft.
models electric and gas dryers
2
45 ft.
35 ft.
(GFDS, GFDR, GFDN, GTDS,
3
35 ft.
25 ft.
GTDN, GHDN, GHDS, GTDP,
GLDP, GTD, HTDP, HTDX)
4
25 ft.
15 ft.
0
90 ft.
60 ft.
1
60 ft.
45 ft.
2
45 ft.
35 ft.
DCVH480
3
35 ft.
25 ft.
0
46 ft.
37 ft.
1
37 ft.
30 ft.
2
30 ft.
22 ft.
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
3
23 ft.
15 ft.
0
56 ft.
42 ft.
1
48 ft.
34 ft.
2
40 ft.
26 ft.
Laundry Center GUD27
3
32 ft.
18 ft.
0
43 ft.
36 ft.
1
33 ft.
26 ft.
Laundry Center GUD24
2
24 ft.
16 ft.
A
For complete information, see installation instructions packed with your dryer.
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all rigid metal
exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semirigid) ducting can be used (Kit WX08X10077). In special installations, it may be
necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.
A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid
metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter
can be maintained throughout the entire length of the transition duct. Please see
installation instruction packed with your dryer for complete instructions when using
flexible metal (foil type) ducting.
Exhaust Length Calculation:
1.Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2.The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated
is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the
duct length should be treated as a 90° elbow. A turn over 45° should be treated as a
90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any
enclosed house floor (crawl space), or into an attic, since the accumulated lint could
create a fire hazard or moisture could cause damage. Never terminate the exhaust
into a common duct or plenum with a kitchen exhaust, since the combination of lint
and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts,
bird nesting, etc. The wall cap must also be located at least 12" above the ground or
any other obstruction with the opening pointed down.
For more information on venting kits and accessories, please call 1-800-GE-CARES.
For every extra 90° elbow, reduce the allowable vent system length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
The total vent system length includes all the straight portions and elbows of
the system (transition duct included).
Specification Revised 4/15
GTDP220GF
GE® 7.0 cu. ft. capacity Dura Drum gas dryer
Features and Benefits
•Dura Drum interior - Enjoy long-lasting durability and fabric protection thanks to
a strong drum construction with a polypropylene-bead-reinforced finish
•4 heat selections - Provide the right temperatures for your clothes-drying needs
•End-Of-Cycle Signal - Alerts you when the load is done, so clothes can be
removed before wrinkles set in
•Auto Dry - For clothes that come out feeling and looking great, this setting
monitors air temperature to set the optimal drying time
•Model GTDP220GFWW –White
GTDP220EFWW
Specification Revised 4/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement