Schumacher Electric SE-2254 Technical data

Add to my manuals
36 Pages

advertisement

Schumacher Electric SE-2254 Technical data | Manualzz

Safety Bus System

AS-Interface Safety at Work

S

R

O R

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

®

AS-Interface Safety at Work

(SaW) is the first safety bus system based upon the open standard of AS-International.

Safety components such as

Emergency Stop command devices, safety switches, solenoid interlocks or safety light barriers are simply connected to the yellow AS-Interface cable. For the evaluation of the safety signals a “Safety Monitor” is merely added to the AS-

Interface system.

AS-Interface Standard in accordance with EN 50295

With the integration of AS-Interface SaW the AS-Interface network will continue to operate unchanged. The well known components, like the standard

AS-Interface master, the standard power supply as well as the

AS-Interface yellow cable will still form the basis of all AS-

Interface installations. Therefore safety functions can be easily added to an exiting machine equipped with AS-Interface SaW.

The heart of safety

The safety monitor analyses all transmitted information from each safety device on the AS-

Interface network and, in case of a safety device being activated or in case of a fault in one of the safety devices, the safety monitor immediately shuts down to create a safe condition. The safety monitor is equipped with one or two redundant pairs of enabling paths for applications up to Control Category 4 according to EN 954-1.

Each safety function of the monitor can be set with simple drag & drop software. Afterwards the parameters are downloaded into the safety monitor and protected with a password.

Easy and safe

Safe transmission mechanism

The communication protocol for safety relevant applications is based on the unchanged AS-

Interface Standard transmission.

With each AS-Interface master call each safety device answers in return with a preset data telegram. This information is analysed and in case of a deviation from the pre-set values the enabling fields are opened. The maximum response time for a safe shutdown is 40 ms.

Cost reduction with

AS-Interface Safety at Work

Reduce cost and installation time – A never ending story.

During installation and machine commissioning as well as during maintenance, AS-Interface SaW supports the user with integrated system diagnosis. It provides detailed information about the cause and place of the failure, and enables the user to quickly find and analyse a malfunction and therefore minimise machine downtime. With AS-

Interface Safety at Work you can directly reduce your cost.

More flexibility with

AS-Interface Safety at Work

For the realisation of individual safety solutions, SCHMERSAL offers the maximum amount of flexibility with its diverse range of safety devices. Depending on the application the user can choose the optimal solution out of an extensive product basket.

As AS-Interface SaW is an open system, the user has also the possibility to include additional

Safety components from other suppliers. AS-Interface Safety at Work fulfils the safety requirements to the highest standards.

2

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

S

R

O R

Less installation time with

AS-Interface Safety at Work

Easier and quicker with AS-

Interface SaW: Choose a Safety device – Connect it to the yellow

AS-Interface cable – Set the safety function in the safety monitor. – That’s it.

No further settings are required at each of the safety devices, the bulky parallel wire cables between the safety devices in the field and the switching cabinet are reduced and wiring time is decreased. The power supply for all safety sensors is supplied over the single yellow AS-Interface cable.

AS-Interface Safety at Work overview

Controller

AS-Interface

Power Master

Safety guard monitoring

E-Stop Command

Safety monitor

Two-Hand Control

AS-Interface SaW

System Features

• Up to 31 standard and safety slaves on the

AS-Interface system

• No Safety PLC necessary

• Safety-relevant signals can be allocated into groups and multiple

Safety monitors may be connected

• Response time is max. 40 ms

• Safety-relevant signals can be integrated into plant diagnostics

• Certified up to Control

Category 4 in accordance with EN 954-1

• Certified by the TÜV

(German Technical

Inspectorate)

Foot switch

Standard AS-Interface Module

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

3

AS-Interface Safety at Work

ASM

• Safety monitor

• Control Category 4 to EN 954-1

• Monitor for AS-Interface SaW compatible safety device, i.e. safety switches, solenoid interlocks, Emergency-Stop buttons,

2-Hand control, light grid and light curtains

• AS-Interface connection

• One or two redundant pairs of enabling paths

• Additional outputs (transistor, short-circuit proof)

• Configurable functions: AND logical element, OR logical element,

Start devices, Start-up test

• Edge-sensitive start push button

• Feedback circuit to monitor external contactors

• LEDs to diplay switching conditions

• Operating voltage 24 VDC

S

R

O R

Technical data

Standards:

Control category:

Enclosure:

Mounting:

Screw terminals:

Protection class:

U b

Ib:

:

Residual ripple:

Switch-on peak current:

AS-Interface operating voltage:

AS-Interface operating current:

AS-Interface specification:

Configuration interface:

Inputs:

Input signal:

Outputs:

EN 50295, EN 61496-1 (1997), IEC/EN 60204-1, EN 954-1, IEC 61508

4

Polyamide PA 66, black snaps onto standard DIN rail to EN 50022 max. 2.5 mm

2

(incl. conductor ferrules) terminals IP 20 enclosure IP 20

24 VDC ± 15 %

< 15%

ASM E1-R2: 0,15 A

ASM E2-R2/R2: 0,2 A

600 mA

18.5 ... 31.6 V

< 45 mA

Profile - Monitor 7.F

RS232: 9600 baud, no parity, 1 start bit, 1 stop bit, 8 data bits

1.Y1,1.Y2

„Y1, Y2“: le < 10 mA at 24 VDC (opto coupler, high-active)

ASM E1-R2: 1.13/14,1.23/24, 1 enabling path (redundant);

ASM E2-R2/R2: 1.13/14,1.23/24, 2.13/14, 2.23/24,

Utilisation category:

I e

/U e

:

Switching voltage:

I the

:

Max. fuse rating:

Additional outputs:

Switch-on time:

Response time:

Indications:

2 enabling paths (redundant)

AC-15, DC-13

3 A / 230 VAC

1 A / 24 VDC max. 230 VAC

3 A per output circuit

4 A (slow blow), external transistor outputs, 200 mA total, short-circuit proof-type, positive-switching

< 10 s

< 40 ms

AS-Interface: voltage LED green, communication LED red;

Enabling paths: LED green, yellow, red

EMC rating:

Overvoltage category:

Resistance to vibration:

Resistance to shock:

Ambient temperature:

Storage and transport temperature:

Weight:

Note: conforming to EMC Directive

III to DIN VDE 0110

5 ... 55 Hz / amplitude 0.35 mm

± 15 % at the regulation point

10 g / 16 ms

– 20 °C … + 60 ºC

– 30 °C … + 70 ºC

ASM E1-R2: approx. 350 g;

ASM E2-R2/R2: approx. 450 g

Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of a suitable circuit.

Approvals

F C D

C

Ordering details

ASM E

No. Replace Description

1-R2

2-R2/R2

1 enabling field

(redundant)

2 enabling fields

(redundant)

Note

The safety monitors ASM E1-R2 and ASM E2-R2/R2 evaluate all transmitted information from each safety device on the AS-Interface network. For the safe guarding of different applications various AS-Interface Safety at Work compatible safety devices are needed, i.e. safety switches, solenoid interlocks, safety sensors, E-stop buttons as well as safe input modules.

The AS-Interface Safety at Work can be used in applications up to control category 4 according to EN 954-1 with the appropriate safety devices and systems.

4

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

Note

• The installation of different safety areas is possible with numerous safety monitors working alongside each other. The maximum number of safety devices including the safety monitors may not exceed 31 participants.

• The allocation of the safety devices to one or more safety monitors is achieved with the help of the configuration software ”asimon“.

• The wiring diagram shows the safety monitor

ASM E2-R2/R2 with start-pushbuttons and feedback loops.

• No safety devices are displayed, because they are installed in the field i.e. on the safety guards itself. The data connection between the safety monitor and the decentralised safety slaves is established via the AS-

Interface network.

• For the operation of AS-Interface Safety at

Work system, a standard controller, an AS-

Interface Master and AS-Interface power supply, must always be used in the application.

• With the RJ 45 connector the safety monitor is configured and started up.

• Start push button

H

A start push button (NO) can optionally be connected to the ASM. With the guard door(s) closed, the enabling paths are then not closed until the start push button has been operated. If neither start button nor feedback circuit are required, then no connections are required to the terminals

(1Y1/2, 2Y1/2).

Wiring diagram

+ 24 VDC

0 V

AS-i-

AS-i+

+ 24 VDC

0 V

S1

S2

N

M1 M2

AS-i+ AS-i1Y1 1Y2 2Y1 2Y2

1.32

2.32

1.13

1.23

2.13

2.23

AS-

Interface

RS

232

L+

24 V

M FE

K1

K3

K2

K4

1.14

1.24

2.14

2.24

K5

K6

L1

L1 L2 L3

3

M

+ 24 VDC

K5

K6

N

K7

2.14

2.24

K8

• Output expander module

For additional contacts by means of more enabling paths and potential-free indication contacts an output expander module is connected to the safety monitor, i.e. to the internal ASM enabling path. For the control of the additional outputs the ASM feedback loop is utilised.

L1 L2 L3

K7

K8

3

M

S

R

O R

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

5

AS-Interface Safety at Work

asimon

The software asimon is a tool for the configuration and commissioning of the

AS-Interface safety monitors.

The configuration of the safety monitor and its safety devices, i.e. E-Stop buttons, solenoid interlocks, safety switches, 2-Hand controls, light curtains etc. is performed by an easyto-use graphical interface. Thus providing safeguarding of hazardous areas present by power-driven machinery.

The asimon offers the user a library of icons representing different safety devices and other functional devices, i.e. one or two independent enabling paths, automatic or monitored start, stop category 0 or 1 etc. For the implementation of a new safety application the required safety devices are selected from the icon library, parameterised and assigned to the respective enabling path.

Following the successful configuration and download, the safety monitor and the safety devices can be tested and monitored with asimon.

The following functions are available with the asimon software:

• Configuration of different safety devices

• Configuration of start-modules

• Configuration logical combinations

(AND, OR, RS Flip-Flops)

• Configuration of the feedback loops

• Configuration of the operating methods

• Configuration of the system-modules

• Print out of Configuration protocol

Asimon can be used offline as well as online during development and project planning.

The configuration files can be saved and loaded as desired.

The software is compatibable with the

Microsoft® operating system

Windows 95/98/ME/NT/2000/XP.

S

R

O R

System components

• Download cable: Interface cable with two RJ 45 connectors, Length: 0.10 m

Part-number: ASM-DC1

• Configuration cable: Interface cable with one RJ 45 and SUBD 9 connector,

Length: 1.2 m

Part-number: ASM-KC1

Approvals

F

C

Ordering details Note

SET ASM-SWP ASM-startup-package:

ASM-CD

Configuration and diagnostic software package with online documentation on CD-ROM, a configuration- and downloadcable asimon software package:

Configuration and diagnosticsoftware package with online documentation on CD-ROM

Hardware requirements:

• 200 MHz INTEL Pentium® or

AMD® Processor or quicker

• Min. 8 Mbyte free main memory (RAM)

• Min. 8 Mbyte free hard disk memory

• A CD-ROM drive (or 3 1/2 “ disc drive) for the installation

• A mouse

• A free serial interface with

9 SubD-connection

Software requirements:

• Microsoft Windows ® 95/98/ME/NT/2000/XP

Ordering details

Download cable

Configuration cable

ASM-DC1

ASM-KC1

6

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

AZ 16 AS

14

M 12

30

8

9

13

5,5

40

M 12

52

• Safety switch with separate actuator

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector

• Address jack (optional)

• Thermoplastic enclosure

• Coded actuator

• Long life

• Protection class IP 67

S

Technical data

Standards:

Enclosure:

EN 50295

EN 60947-5-1

EN 954-1 glass-fibre reinforced thermoplastic, self-extinguishing

AS-Interface connection type:

Protection class:

AS-Interface operating voltage: connector M12 x 1

IP 67

26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

AS-Interface specification:

) 50 mA

Profile S-0.B

IO-Code: 0x0

ID-Code: 0xB

ID-Code2: 0xE

Inputs:

Contact Status

1 on D0/D1 = dynamic code transmission

1

2 off on

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

2 off

Parameter bits:

D2/D3 = static code “00”

P0 … P3 not used

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications:

AS-Interface:

Enabling status:

Mechanical life:

EMC rating:

Ambient temperature:

Storage and transport temperature: voltage LED green, communication LED red

LED yellow

> 1 million operations conforming to

EMC Directive

– 25 °C … + 60 ºC

– 25 °C … + 85 ºC

System components

16

ø 5,5 a

ø 5,5

56

40

56

40

27

Straight actuator AZ 15/16-B1 a

27,3

27

Flexible actuator AZ 15/16-B2

ø 5,5

56

40

27,3

27

Flexible actuator AZ 15/16-B6

R

O R

R min. 15

0

R min. 15

0

R min. 4

5

R min. 38

R min. 25

Approvals

F C D

C

Ordering details

AZ 16

-AS

➁➂

No. Replace Description

ST1

ST2

ST3

➂ r r-2254 b

Connector (middle)

Connector (right)

Connector (left)

No latching

Latching 30 N

Latching 5 N

No address jack

Address jack

2

1

Note

4

3

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

Ordering details

Straight actuator

Flexible actuator

Flexible actuator

AZ 15/16-B1

AZ 15/16-B2

AZ 15/16-B6

Further actuators can be found in the chapter

„Safety switches with separate actuator“, see page 1-8.

Actuators must be ordered separately.

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

7

AS-Interface Safety at Work

S

R

O R

AZM 161 AS

6 40 a

5,5 b

M12

130

78

72

56

6

M12

30

• Solenoid interlock

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector

• Magnetic drive through AS-Interface output

• Solenoid power supply via the

AS-Interface network or via an external

24 VDC power supply (p version)

• Address jack (optional)

• Thermoplastic enclosure

• Manual release, emergency exit or emergency release

• High holding force 2000 N

• 30 N latching force (optional)

• Power to unlock / power to lock principle

• Actuating play 5.5 mm in direction of actuation

• Protection class IP 67

Technical data Note

Standards:

Enclosure:

EN 50295

EN 60947-5-1

EN 954-1 glass-fibre reinforced thermoplastic, self-extinguishing

AS-Interface connection type:

Protection class:

AS-Interface operating voltage: connector M12 x 1

IP 67

26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current: Total:

) 500 mA

AS electronics:

) 50 mA

AS-Interface specification: Profile S-7.B

IO-Code 0x7

ID-Code 0xB

ID-Code2 0xE

Inputs:

Contact Status

1 on D0/D1 = dynamic code

1

2 off on transmission

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

D2/D3 = static code “00”

A0 Solenoid control

2

Outputs: off

A1 … A3 not used

Parameter bits: P0 Actuator / interlock status

P1 … P3 not used

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications:

AS-Interface:

Enabling status:

Mechanical life:

F max

:

EMC rating: voltage LED green, communication LED red

LED yellow

> 1 million operations

2000 N conforming to EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

The AZM 161 Z version must be selected for applications where safety guard locking is required. The AZM 161 B version has a safetymonitored actuator with supplementary guard locking function.

Depending on the device version, the safety inputs (D0-D3) are connected internally to the solenoid (Z) or actuator contacts (B). The safety monitor (ASM) monitors the coded data transmission.

Output A0 is used to lock or unlock the solenoid of the solenoid interlock. Parameter bit P0 gives the control system feedback about the status of the actuator or solenoid interlock.

Parameter bit:

The status of the actuator or the locking bolt can be monitored by the parameter bit P0 depending on the device:

Device Parameter bit P0

AZM 161 B

AZM 161 B

0

1

AZM 161 Z

AZM 161 Z

0

1 status

Guard locked

Guard unlocked

Guard closed

Guard open

Approvals only without address jack

F C D

C

Ordering details

AZM 161

➀➁

-AS

➂➃➄➅➆

No. Replace Description

B

Z

ST1

ST2 r a b

Actuator monitored

Guard locking monitored

Connector (middle)

Connector (right)

No latching

Latching 30 N

Power to unlock

Power to lock

No address jack

Address jack

1

Note

4

No. Replace Description

➆ p

N

T

Integrated solenoid supply

External solenoid supply

Manual release

Emergency release

Emergency exit

2 3

M12 connector:

1: AS-Interface +

2: Aux – (p)

3: AS-Interface –

4: Aux + (p)

8

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

Contact variants

Integrated power supply

Power to unlock

Guard locking monitored

Contact variants

External power supply

Power to unlock

Guard locking monitored

AS-i

-

+

P0 D0-D3

A0

Actuator monitored

AS-i

-

+

P0 A0 D0-D3

-

+

24 VDC

Actuator monitored

AS-i

-

+

D0-D3 P0

A0

Power to lock

Guard locking monitored

AS-i

-

+

P0 D0-D3

A0

Actuator monitored

AS-i

-

+

D0-D3 P0

A0

AS-i

-

+

D0-D3 A0 P0

-

+

24 VDC

Power to lock

Guard locking monitored

AS-i

-

+

P0 A0 D0-D3

-

+

24 VDC

Actuator monitored

AS-i

-

+

D0-D3 A0 P0

-

+

24 VDC

S

R

O R

Note

Integrated power supply:

The solenoid interlock AZM 161 AS is powered by the AS-Interface. Connection to the AS-

Interface is made via the M12 connector.

The required supply voltage for the solenoid is also supplied by the AS network.

The maximum number of interlocks with integrated power supply and power to lock principle (a) depends solely on the employed

AS-Interface power supply and its electric current output.

To lock or unlock the guard door, the network must supply a maximum current of 0.5 A per solenoid interlock.

External power supply:

The solenoid interlock AZM 161 AS ...p is monitored by the AS-Interface. The locking solenoid is powered by an external power supply. Connection to the AS-Interface and the auxiliary power is made via a single

M12 connector.

The necessary solenoid supply voltage is provided externally (auxiliary power).

Up to 29 solenoid interlocks with an external power supply can be operated on one AS-Interface network depending on the application.

Solenoid control:

An internal output controls the solenoid operation. Depending on the device version, the output bit A0 locks or releases the actuator.

The output bit A0 has the same address as the safety inputs.

Legend

D0 – D3 Coded data for the evaluation

P0

A0 of the safety monitor (4 Bit)

Status signal (1 Bit)

Output for switching the solenoid (1 Bit)

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

9

AS-Interface Safety at Work

ZS 71 AS

40

30

33

M 12

52

18

17,5

24

10

42

M 12

15

• Pull-wire Emergency-Stop switch

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector

• Metal enclosure

• Various spring force variants

(actuating forces)

• Adjustable actuating force

• Wire up to 20 m long

• Reset by push button or key possible

• Protection class IP 65 (with push button and external watertight collar)

Approvals

F C D

C

Ordering details

ZS 71

-AS

➁➂

-

-

/

No. Replace Description

ST1

W

VD

VS

A

G

55 N

200 N

Connector

Without watertight collar

With watertight collar

Without safety function

Push button reset

Key reset

Without position indicator

With position indicator

Without indicator lamp

With indicator lamp

Pre-tensioning force:

For wire length 0 - 5 m

For wire length 5 - 20 m

Technical data

Standards: EN 50295, EN 60947-5-1, EN 954-1

Enclosure: cast aluminium, enamelled

Cover: thermoplastic ultramid

AS-Interface connection type:

Protection class: connector M12 x 1

IP 54

IP 65 for version with push button reset and watertight collar

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

) 50 mA, with indicator lamp

) 130 mA

AS-Interface specification: Profile S-0.B

(with indicator lamp) S-7.B

IO-Code 0x0

Inputs:

Contact Status

1 on

(with indicator lamp) 0x7

ID-Code 0xB

ID-Code2 0xE

D0/D1 = dynamic code transmission

1

2

2

Outputs: off on off

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

D2/D3 = static code “00”

A0 Indicator lamp (optional)

A1 … A3 not used

P0 … P3 not used Parameter bits:

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status: LED yellow

Mechanical life:

Maximum cable length:

Features:

> 1 million operations

20 m wire pull and

EMC rating: breakage detection conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

Note

A separate address jack is not available as an option. The addressing must take place via the cable end or the M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

A wide range of accessories is available.

For selection, see page 2-9.

S

R

O R

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

ZS 73 AS

25

M 12

56

28

M 12

70

98

5

170

15

75

• Pull-wire Emergency-Stop switch

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector

• Metal enclosure

• 4 various spring force variants

(actuating forces)

• Adjustable actuating force

• Wire up to 50 m long

• Reset by push button or key possible

• Protection class IP 65 (with push button and external watertight collar)

Approvals

F C D

C

Ordering details

ZS 73

-AS

➁➂

-

/

No. Replace Description

ST1

W

Connector

Without watertight collar

With watertight collar

Without safety function

Push button reset VD

VS

G

Key reset

Without indicator lamp

With indicator lamp

80-100N Pre-tensioning force:

For wire length 0-10 m

120-180N For wire length 10-20 m

195-275N For wire length 20-30 m

295-390N For wire length 30-50 m

Technical data

Standards: EN 50295, EN 60947-5-1, EN 954-1

Enclosure: cast aluminium, enamelled

Cover: thermoplastic ultramid

AS-Interface connection type:

Protection class: connector M12 x 1

IP 54

IP 65 for version with push button reset and watertight collar

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

) 50 mA, with indicator lamp

) 130 mA

AS-Interface specification: Profile S-0.B

(with indicator lamp) S-7.B

IO-Code 0x0

Inputs:

Contact Status

1 on

(with indicator lamp) 0x7

ID-Code 0xB

ID-Code2 0xE

D0/D1 = dynamic code transmission

1

2

2

Outputs: off on off

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

D2/D3 = static code “00”

A0 Indicator lamp (optional)

A1 … A3 not used

P0 … P3 not used Parameter bits:

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status: LED yellow

Mechanical life:

Maximum cable length:

Features:

> 1 million operations

50 m wire pull and

EMC rating: breakage detection conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

Note

A separate address jack is not available as an option. The addressing must take place via the cable end or the M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

A wide range of accessories is available.

For selection, see page 2-9.

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

S

R

O R

Phone: 905-738-6688

11

AS-Interface Safety at Work

ZS 75 AS

69

54

23

27

12

33

154

76

71

14

M 12 M 12

70

100

• Pull-wire Emergency-Stop switch

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector

• Metal enclosure

• 4 various spring force variants

(actuating forces)

• Adjustable actuating force

• Wire up to 50 m long

• Reset by push button or key possible

• Protection class IP 65 (with push button and external watertight collar)

Approvals

F C D

C

Ordering details

ZS 75

-AS

➁➂

-

/

No. Replace Description

ST1

W

Connector

Without watertight collar

With watertight collar

Without safety function

Push button reset VD

VS

G

Key reset

Without indicator lamp

With indicator lamp

80-100N Pre-tensioning force:

For wire length 0-10 m

120-180N For wire length 10-20 m

195-275N For wire length 20-30 m

295-390N For wire length 30-50 m

Technical data

Standards: EN 50295, EN 60947-5-1, EN 954-1

Enclosure: cast aluminium, enamelled

Cover: cast aluminium, enamel finish

AS-Interface connection type:

Protection class: connector M12 x 1

IP 54

IP 65 for version with push button reset and watertight collar

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

) 50 mA, with indicator lamp

) 130 mA

AS-Interface specification: Profile S-0.B

(with indicator lamp) S-7.B

IO-Code 0x0

Inputs:

Contact Status

1 on

(with indicator lamp) 0x7

ID-Code 0xB

ID-Code2 0xE

D0/D1 = dynamic code transmission

1

2

2

Outputs: off on off

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

D2/D3 = static code “00”

A0 Indicator lamp (optional)

A1 … A3 not used

P0 … P3 not used Parameter bits:

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status: LED yellow

Mechanical life:

Maximum cable length:

Features:

> 1 million operations

50 m wire pull and

EMC rating: breakage detection conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

Note

A separate address jack is not available as an option. The addressing must take place via the cable end or the M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

A wide range of accessories is available.

For selection, see page 2-9.

S

R

O R

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

NAS 311 AS

M 12

85

M 12

97,8

37,8

• E-STOP station

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector

• Pull to reset

• Resistant to chemicals

• Protection class IP 65

Technical data

Standards: EN 50295, EN 60947-5-1, EN 954-1

Enclosure: glass-fibre reinforced polyamide nylon,

Emergency-Stop button: self-extinguishing thermoplastic or aluminium

AS-Interface connection type:

Protection class:

AS-Interface operating voltage: connector M12 x 1

IP 65

26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

AS-Interface specification:

) 50 mA

Profile S-0.B

IO-Code: 0x0

ID-Code: 0xB

ID-Code2: 0xE

Inputs:

Contact Status

1 on D0/D1 = dynamic code transmission

1

2 off on

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

2 off

Parameter bits:

D2/D3 = static code “00”

P0 … P3 not used

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green,

EMC rating: communication LED red

Enabling status: LED yellow conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

Approvals

F C D

C

Ordering details

NAS 311

-AS

No. Replace Description

ST1

M

MH

Connector

Thermoplastic enclosure

Metal housing

Metal housing and push button with protection collar

Note

A separate address jack is not available as an option. The addressing must take place via the cable end or the M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

S

R

O R

Phone: 905-738-6688

13

AS-Interface Safety at Work

AST ... AS

• Input module

• 2 safe inputs for mechanical contacts

• Cross-wire monitoring

• Magnetic drive through

AS-Interface output

• Solenoid power supply via via an external 24 VDC power supply

• AS-Interface LED status display

• AS-Interface M12 connector

• Thermoplastic enclosure

• Long life

• Protection class IP 67

• Connection of NC/NC contact or NC/NO contact combination

S

R

O R

Technical data

Standards:

Enclosure:

AS-Interface connection type:

Protection class:

AS-Interface operating voltage:

AS-Interface operating current:

AS-Interface specification:

Inputs:

Outputs:

Parameter bits:

Input module address:

Indications:

EMC rating:

Ambient temperature:

Storage and transport temperature:

EN 50295, EN 60947-5-1, EN 954-1 glass-fibre reinforced thermoplastic, self-extinguishing

(see ordering data)

IP 67

26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

) 50 mA

Profile S-7.B

IO-Code

ID-Code

ID-Code2

0x7

0xB

0xE

Contact Status

1 on

1 off

2

2 on off

D0/D1 = dynamic code transmission

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

D2/D3 = static code “00”

A0 Solenoid control

A1... A3 not used

P0 … P3 not used default on address 0, programmable via the AS-Interface Master

AS-Interface: or Hand-held programming device supply voltage green LED, communication red LED, blinking = cross-wire short

Enabling status: LED1/contact1, yellow/contact2 conforming to EMC Directive

– 25 °C … + 55 ºC

– 25 °C … + 85 ºC

Approvals

F C D

C

Ordering details

AST

➀➁

-AS

➂➃

No. Replace Description

02

11

ST

L

2

4

6

ST

1 NC/1 NC

1 NO/1 NC

M12 connector

Cable (2m)

2 x 2-single conductors

(2 safety inputs)

1 x 4-single conductors

(2 safety inputs)

1 x 6-single conductors

(2 safety inputs and

1 semiconductor output)

M12 connector with

2m cable (2 x 2 or 1 x 4)

2

1

Note

4

3

M12 connector:

1: AS-Interface +

2: Aux – (6) (AST...6)

3: AS-Interface –

4: Aux + (6) (AST...6)

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

Note

• The wiring diagram is shown with guard doors closed and in de-energised condition.

Wiring diagram

• Monitoring a sliding guard door using two position switches with safety function.

The NC contact must have positive break when the guard door is opened.

• The module AST...AS is monitored by the

AS-Interface. The locking solenoid is powered by an external power supply.

Connection to the AS-Interface and the auxiliary power is made via a single M12 connector or via a 4-pole connecting cable.

• The necessary solenoid supply voltage is provided externally (auxiliary power).

• An internal output controls the solenoid operation. Depending on the interlocking device, output bit A0 locks or unlocks the actuator. Output bit A0 has the same address as the safety inputs.

bn bu bn bu

AST

02

AS 02

AS-i

13 14 21 22 bn bu wh bk

AZM 170-11z

A1 A2 rd gy

24 V DC

AST

11

AS 06

AS-i

S

R

O R

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688

15

AS-Interface Safety at Work

BNS 16 AS

M 12

39

17

9

52

M 12

40

• Safety sensor

• Integrated AS-Interface

• AS-Interface LED status display

• Available with M12 plug-in connetor and pre-wired cable

• Thermoplastic enclosure

• Coded actuator

• Long life, no mechanical wear

• Intensitive to transverse misalignment

• Concealed mounting possible

• Intensitive to soiling

• Protection class IP 67

M20 x 1,5

S

Technical data

Standards:

Enclosure:

EN 50295

EN 60947-5-1

EN 954-1 glass-fibre reinforced thermoplastic, self-extinguishing

AS-Interface connection type:

Protection class:

AS-Interface operating voltage: connector M12 x 1

IP 67

26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

AS-Interface specification:

) 100 mA

Profile: S-0.B

IO-Code: 0x0

ID-Code: 0xB

ID-Code2: 0xE

Inputs:

Contact Status

1 on D0/D1 = dynamic code transmission

1

2 off on

2 off

Parameter bits:

D2/D3 = static code “00”

P0 … P3 not used

Input module address: Default on address 0

Indications:

AS-Interface:

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

Enabling status: voltage LED green, communication LED red

LED yellow

Mode of operation:

Sao:

Sar:

Repeat accuracy R:

Switching frequency f:

Actuating magnet:

EMC rating: magnetic

8 mm

18 mm

) 0,1 x Sao

< 1 Hz

BPS 16, coded conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

System components

20

60

40

Actuating magnet BPS 16

Actuating planes

¤ 5,5

R

O R

Approvals

F C D AE-i

Ordering details

BNS 16

-AS

No. Replace Description

ST1

ST2

ST3

V

D

Connector (middle)

Connector (right)

Connector (left)

Actuating planes: front side cover-side

2

1

Note

4

3

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

Ordering details

Actuating magnet

Actuators must be ordered separately.

BPS 16

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

System components System components

AS-i

+

AS-i

-

Aux

+

Aux

-

IDC connector (M12 outlet)

5 2

Aux -

4

Aux +

3

AS-i -

1

AS-i +

Passive connection module (M12 outlet)

IDC connector (screw outlet)

M 5

34

50

64

Terminal mounting H 30

S

R

O R

Ordering details

IDC connector (M12 outlet)

IDC connector (screw outlet)

Terminal mounting H 30

Ordering details

Passive connection module (M12 outlet)

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688

17

AS-Interface Safety at Work

S

R

O R

ASU command devices

23,5 75

• Emergency-Stop button

• Compact embeddable command devices with ASU adapter box

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector,

IDC connector

• Miscellanous positioning parts

(metal, plastic)

• Mounting hole 22.3 mm

(to EN 50 007)

• Protection class IP 65 (from front)

Ø 38,5

38

Approvals

F

C

Ordering details

EFP

-AS

DRZ 40 RT

Contact block

Actuating element

No. Replace Description

ST

DT

ME

30

330

E

K

M12 connector

Flat cable connection (DC) optional: 2 m cable, cable gland, flying lead

1 NC

2 NC

Metal actuating element

Plastic actuating element

Technical data Technical data

Standards:

Enclosure:

EN 50295

EN 60947-5-1

EN 954-1 glass-fibre reinforced polyamide nylon, self-extinguishing

AS-Interface connection type:

Protection class:

(see ordering data)

IP 65 (front)

IP 20 (rear of the front plate)

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

AS-Interface specification:

) 50 mA

Profile

IO-Code

ID-Code

ID-Code2

S-7.B

0x7

0xB

0xE

Inputs:

Contact Status

1 on D0/D1 = dynamic code

1

2 off on transmission

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

D2/D3 = static code “00”

P0 … P3 not used

2 off

Parameter bits:

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status: LED yellow

Resistance to shock: 110 g/4 ms…30 g/18 ms, no bouncing

(for actuating heads with higher respectively lower weight)

Resistance to vibration:

* 20 g / 10 …200 Hz

(for actuating heads with higher respectively lower weight)

EMC rating: conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

Actuating elements

Al-metal actuating element:

Resistance to shock:

Resistance to vibration: max. 15 g / 22 ms*

(temporary data) max. 0.35 mm,

0 … 150 Hz

Plastic actuating element:

Resistance to shock: max. 15 g / 22 ms*

Resistance to vibration:

(temporary data) max. 0.35 mm,

0 … 150 Hz

* preliminary data

Note

Addressing through flat cable connection or through M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

2

1

Flat cable connection:

1: AS-i +

2: AS-i –

Note

Mounting

One-hole fixation 22.3 mm + 0.4 mm to

EN 50 007 (a tail cut-out as displacement protection is not required for Elan devices)

The positioning parts are not included in delivery.

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

S

R

O R

ASU command devices Technical data

23,5 75

Ø 29,5 (29,8)

Ø 22 (25)

• Push button

• Compact embeddable command devices with ASU adapter box

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector,

IDC connector

• Miscellanous positioning parts

(metal, plastic)

• Mounting hole 22.3 mm

(to EN 50 007)

• Protection class IP 65 (from front)

38

Standards: EN 50295

EN 60947-5-1

EN 954-1

Enclosure:

AS-Interface connection type:

Protection class: glass-fibre reinforced polyamide nylon, self-extinguishing

(see ordering data)

IP 65 (front)

IP 20 (rear of the front plate)

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

) 50 mA

AS-Interface specification: Profile

IO-Code

S-7.B

0x7

ID-Code

ID-Code2

0xB

0xE

Inputs:

Contact Status

1 on

1 off

D0/D1 = dynamic code transmission

D0/D1 = static code “00”

2 on

2 off

D2/D3 = dynamic code transmission

D2/D3 = static code “00”

Parameter bits: P0 … P3 not used

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status: LED yellow

Resistance to shock: 110 g/4 ms…30 g/18 ms, no bouncing

(for actuating heads with higher respectively lower weight)

Resistance to vibration:

* 20 g / 10 …200 Hz

(for actuating heads with

EMC rating: higher respectively lower weight) conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

Approvals

F

C

Ordering details

EFP

-AS

DT

Contact block

Actuating element

No. Replace Description

ST

DT

ME

03

033

E

K

GN*

SW*

BL*

M12 connector

Flat cable connection (DC) optional: 2 m cable, cable gland, flying lead

1 NO

2 NO

Metal actuating element

Plastic actuating element

Green push-button

Black push-button

Blue push-button

Other colours on request

Note

Addressing through flat cable connection or through M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

2

1

Flat cable connection:

1: AS-i +

2: AS-i –

Note

Mounting

One-hole fixation 22.3 mm + 0.4 mm to

EN 50 007 (a tail cut-out as displacement protection is not required for Elan devices)

The positioning parts are not included in delivery.

* Push-buttons in different colours available on request.

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688

19

AS-Interface Safety at Work

S

R

O R

ASU command devices

23,5 75

Ø 29,5 (29,8)

Ø 22 (25)

• Illuminated push-button

• Compact embeddable command devices with ASU adapter box

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector,

IDC connector

• Miscellanous positioning parts

(metal, plastic)

• Mounting hole 22.3 mm

(to EN 50 007)

• Protection class IP 65 (from front)

38

Approvals

F

C

Ordering details

EFP

-AS

DL

Contact block

Actuating element

No. Replace Description

ST

DT

ME

03L

E

K

GN*

SW*

M12 connector

Flat cable connection (DC) optional: 2 m cable, cable gland, flying lead

1 NO

Metal actuating element

Plastic actuating element

Green illuminated push-button

Black illuminated push-button

Other colours on request

Technical data

Standards: EN 50295

EN 60947-5-1

EN 954-1

Enclosure:

AS-Interface connection type:

Protection class: glass-fibre reinforced polyamide nylon, self-extinguishing

(see ordering data)

IP 65 (front)

IP 20 (rear of the front plate)

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

) 50 mA, with illuminated pushbutton

) 70 mA

AS-Interface specification : Profile

IO-Code

ID-Code

S-7.B

0x7

0xB

ID-Code2 0xE

Inputs:

Contact Status

1 on D0/D1 = dynamic code

1

2 off on transmission

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

D2/D3 = static code “00”

A0 Indicator lamp

2

Outputs: off

Parameter bits:

A1 ... A3 not used

P0 … P3 not used

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status: LED yellow

Resistance to shock: 110 g/4 ms…30 g/18 ms, no bouncing

(for actuating heads with higher respectively lower weight)

Resistance to vibration: * 20 g / 10 …200 Hz

(for actuating heads with

EMC rating: higher respectively lower weight) conforming to

EMC Directive

Ambient temperature: – 25 °C … + 60 ºC

Storage and transport temp.: – 25 °C … + 85 ºC

Note

Addressing through flat cable connection or through M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

2

1

Flat cable connection:

1: AS-i +

2: AS-i –

Note

Mounting

One-hole fixation 22.3 mm + 0.4 mm to

EN 50 007 (a tail cut-out as displacement protection is not required for Elan devices)

The positioning parts are not included in delivery.

* Push-buttons in different colours available on request.

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

ASU command devices

• Other ASU command devices on request

Technical data

Standards: EN 50295

EN 60947-5-1

EN 954-1

Enclosure:

AS-Interface connection type:

Protection class: glass-fibre reinforced polyamide nylon, self-extinguishing

(see ordering data)

IP 65 (front)

IP 20 (rear of the front plate)

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

) 50 mA

AS-Interface specification : Profile

IO-Code

S-7.B

0x7

ID-Code

ID-Code2

0xB

0xE

Inputs:

Contact Status

1 on

1 off

D0/D1 = dynamic code transmission

D0/D1 = static code “00”

2 on

2 off

D2/D3 = dynamic code transmission

D2/D3 = static code “00”

Parameter bits: P0 … P3 not used

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status:

Switching frequency:

LED yellow

3600/h

Resistance to shock: 30 g/18 ms, no bouncing

(for actuating heads with higher respectively lower weight)

Resistance to vibration:

* 15 g / 10 ... 200 Hz

(for actuating heads with

EMC rating: higher respectively lower weight) conforming to

EMC Directive

Ambient temperature: – 25 °C … + 60 ºC

Storage and transport temp.: – 25 °C … + 85 ºC

Approvals

F

C

Ordering details on request

Note

Addressing through flat cable connection or through M12 connector.

1

1 4

2 3

2

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

Flat cable connection:

1: AS-i +

2: AS-i –

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

S

R

O R

Phone: 905-738-6688

21

AS-Interface Safety at Work

S

R

O R

ASU position switches

23,5

30

22

20

35

75

7,8 10

20

23,7

• Position switch with offset roller lever

• Compact position switches with ASU-adapter box

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector,

IDC connector

• Mounting details to EN 50 047

• Positive break contacts

• Protection class IP 65 (from front)

38

Approvals

F

C

Ordering details

SESR

➀ ➁

-AS

No. Replace Description

11

13

ST

DT

ME

110

Metal roller

Plastic roller

M12 connector

Flat cable connection (DC) optional: 2 m cable, cable gland, flying lead

2 NC

Technical data Contact variants

Standards:

Enclosure:

Design:

AS-Interface connection type:

Protection class:

EN 50295

EN 60947-5-1

EN 954-1 glass-fibre reinforced polyamide nylon, self-extinguishing fixings to EN 50047

(see ordering data)

IP 65 (front)

IP 20 (rear of the front plate)

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

AS-Interface specification :

) 50 mA

Profile

IO-Code

ID-Code

ID-Code2

S-7.B

0x7

0xB

0xE

Inputs:

Contact Status

1 on D0/D1 = dynamic code

1

2 off on transmission

D0/D1 = static code “00”

D2/D3 = dynamic code

2 off transmission

D2/D3 = static code “00”

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status: LED yellow

Switching frequency: 3600/h

Resistance to shock: 30 g/18 ms, no bouncing

(for actuating heads with higher respectively lower weight)

Resistance to vibration: * 15 g / 10 ... 200 Hz

(for actuating heads with

EMC rating: higher respectively lower weight) conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

Switching angle

0 3 6

Note

Addressing through flat cable connection or through M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

2

1

Flat cable connection:

1: AS-i +

2: AS-i –

Note

General use

Actuating angle:

Actuating direction of max. 30° the actuating heads: 4 x 90° repositioned

Repeat accuracy of switching points for plastic rollers: for metal rollers: at the plunger:

Plastic roller

Actuating speed (normally):

Metal roller

± 0,2 mm

± 0,1 mm

± 0,01 mm

> 30m/min.

Actuating speed

(temperatures > 50°C):

Mounting:

Recommended: max. 30 m/min cylindric screws M4 x 25

ISC 1207 (DIN 84), spring washer A4 DIN 137

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

S

R

O R

ASU position switches Technical data Contact variants

23,5

30

22

20

35

75

7,8

20

43,5

10

23,7

38

• Position switches with vertical roller lever

• Compact position switches with ASU-adapter box

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector,

IDC connector

• Mounting details to EN 50 047

• Positive break contacts

• Protection class IP 65 (from front)

5

Approvals

F

C

Ordering details

SESH

➀ ➁

-AS

No. Replace Description

15

17

ST

DT

ME

110

Metal roller

Plastic roller

M12 connector

Flat cable connection (DC) optional: 2 m cable, cable gland, flying lead

2 NC

Standards:

Enclosure:

Design:

AS-Interface connection type:

Protection class:

EN 50295

EN 60947-5-1

EN 954-1 glass-fibre reinforced polyamide nylon, self-extinguishing fixings to EN 50047 connector M12 x 1

IP 65 (front)

IP 20 (rear of the front plate)

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

AS-Interface specification :

) 50 mA

Profile

IO-Code

ID-Code

ID-Code2

S-7.B

0x7

0xB

0xE

Inputs:

Contact Status

1 on D0/D1 = dynamic code

1

2 off on transmission

D0/D1 = static code “00”

D2/D3 = dynamic code

2 off transmission

D2/D3 = static code “00”

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status: LED yellow

Switching frequency: 3600/h

Resistance to shock: 30 g/18 ms, no bouncing

(for actuating heads with higher respectively lower weight)

Resistance to vibration: * 15 g / 10 ... 200 Hz

(for actuating heads with

EMC rating: higher respectively lower weight) conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

Switching angle

60° 10° 0° 10° 60°

Note

Addressing through flat cable connection or through M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

2

1

Flat cable connection:

1: AS-i +

2: AS-i –

Note

General use

Actuating angle:

Actuating direction of max. 30° the actuating heads: 4 x 90° repositioned

Repeat accuracy of switching points for plastic rollers: for metal rollers: at the plunger:

Plastic roller

Actuating speed (normally):

Metal roller

± 0,2 mm

± 0,1 mm

± 0,01 mm

> 30m/min.

Actuating speed

(temperatures > 50°C):

Mounting:

Recommended: max. 30 m/min cylindric screws M4 x 25

ISC 1207 (DIN 84), spring washer A4 DIN 137

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688

23

AS-Interface Safety at Work

S

R

O R

ASU position switches

23,5

30

22

20

35

75

7,8

20

10

23,7

38

• Position switches with vertical plunger

• Compact position switches with ASU-adapter box

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector,

IDC connector

• Mounting details to EN 50 047

• Positive break contacts

• Protection class IP 65 (from front)

Approvals

F

C

Ordering details

SES

-AS

No. Replace Description

ST

DT

ME

110

M12 connector

Flat cable connection (DC) optional: 2 m cable, cable gland, flying lead

2 NC

Technical data Contact variants

Standards:

Enclosure:

Design:

AS-Interface connection type:

Protection class:

EN 50295

EN 60947-5-1

EN 954-1 glass-fibre reinforced polyamide nylon, self-extinguishing fixings to EN 50047 connector M12 x 1

IP 65 (front)

IP 20 (rear of the front plate)

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

AS-Interface specification :

) 50 mA

Profile

IO-Code

ID-Code

ID-Code2

S-7.B

0x7

0xB

0xE

Inputs:

Contact Status

1 on D0/D1 = dynamic code

1

2 off on transmission

D0/D1 = static code “00”

D2/D3 = dynamic code

2 off transmission

D2/D3 = static code “00”

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status: LED yellow

Switching frequency: 3600/h

Resistance to shock: 30 g/18 ms, no bouncing

(for actuating heads with higher respectively lower weight)

Resistance to vibration: * 15 g / 10 ... 200 Hz

(for actuating heads with

EMC rating: higher respectively lower weight) conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

Switching angle

0 3 6

Note

Addressing through flat cable connection or through M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

2

1

Flat cable connection:

1: AS-i +

2: AS-i –

Note

General use

Actuating angle:

Actuating direction of max. 30° the actuating heads: 4 x 90° repositioned

Repeat accuracy of switching points for plastic rollers: for metal rollers: at the plunger:

Plastic roller

Actuating speed (normally):

Metal roller

± 0,2 mm

± 0,1 mm

± 0,01 mm

> 30m/min.

Actuating speed

(temperatures > 50°C):

Mounting:

Recommended: max. 30 m/min cylindric screws M4 x 25

ISC 1207 (DIN 84), spring washer A4 DIN 137

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

S

R

O R

ASU position switches Technical data Contact variants

23,5

30

22

Ø 10

20

35

75

7,8 10

20

4

23,7

38

• Position switches with vertical roller plunger

• Compact position switches with ASU-adapter box

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector,

IDC connector

• Mounting details to EN 50 047

• Positive break contacts

• Protection class IP 65 (from front)

Approvals

F

C

Ordering details

SESB

➀ ➁

-AS

No. Replace Description

31

33

ST

DT

ME

110

Metal roller

Plastic roller

M12 connector

Flat cable connection (DC) optional: 2 m cable, cable gland, flying lead

2 NC

Standards:

Enclosure:

Design:

AS-Interface connection type:

Protection class:

EN 50295

EN 60947-5-1

EN 954-1 glass-fibre reinforced polyamide nylon, self-extinguishing fixings to EN 50047 connector M12 x 1

IP 65 (front)

IP 20 (rear of the front plate)

AS-Interface operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

AS-Interface specification :

) 50 mA

Profile

IO-Code

ID-Code

ID-Code2

S-7.B

0x7

0xB

0xE

Inputs:

Contact Status

1 on D0/D1 = dynamic code

1

2 off on transmission

D0/D1 = static code “00”

D2/D3 = dynamic code

2 off transmission

D2/D3 = static code “00”

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status: LED yellow

Switching frequency: 3600/h

Resistance to shock: 30 g/18 ms, no bouncing

(for actuating heads with higher respectively lower weight)

Resistance to vibration: * 15 g / 10 ... 200 Hz

(for actuating heads with

EMC rating: higher respectively lower weight) conforming to

EMC Directive

– 25 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

Switching angle

0 3 6

Note

Addressing through flat cable connection or through M12 connector.

2

1

3

4

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

2

1

Flat cable connection:

1: AS-i +

2: AS-i –

Note

General use

Actuating angle:

Actuating direction of max. 30° the actuating heads: 4 x 90° repositioned

Repeat accuracy of switching points for plastic rollers: for metal rollers: at the plunger:

Plastic roller

Actuating speed (normally):

Metal roller

± 0,2 mm

± 0,1 mm

± 0,01 mm

> 30m/min.

Actuating speed

(temperatures > 50°C):

Mounting:

Recommended: max. 30 m/min cylindric screws M4 x 25

ISC 1207 (DIN 84), spring washer A4 DIN 137

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688

25

AS-Interface Safety at Work

BNS 33 AS

4,5

ø 5

88

78

LED

2000

• Safety sensor

• Integrated AS-Interface

• AS-Interface LED status display

• Available with M12 plug-in connetor and pre-wired cable

• Thermoplastic enclosure

• Coded actuator

• Long life, no mechanical wear

• Intensitive to transverse misalignment

• Concealed mounting possible

• Intensitive to soiling

• Protection class IP 67

S

Technical data

Standards:

Enclosure:

EN 50295

EN 60947-5-1

EN 954-1 glass-fibre reinforced thermoplastic

AS-Interface connection type:

Cable section:

Protection class:

AS-Interface cable LSYY (black)

2 x 0.24 mm

2

IP 67 operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

AS-Interface operating current:

) 50 mA

AS-Interface specification: Profile: S-0.B

IO-Code: 0x0

ID-Code: 0xB

ID-Code2: 0xE

Inputs:

Contact Status

1 on

1

2 off on

D0/D1 = dynamic code transmission

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

D2/D3 = static code “00” 2 off

Parameter bits: P0 … P3 not used

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green, communication LED red

Enabling status:

Mode of operation:

S ao

:

S ar

:

Actuating magnet:

EMC rating:

LED yellow magnetic

5 mm

15 mm

BPS 33, coded conforming to

EMC Directive

– 25 °C … + 70 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

System components

4,5

88

78

Actuating magnet BPS 33

ø 5

Spacer BN 31/33

78

88

R

O R

Approvals

F C D

C

Ordering details

BNS 33

-AS

No. Replace Description

STG

STW

2 m cable

2 m cable with straight plug M12

2 m cable with angled plug M12

Note

A separate address jack is not available as an option. The addressing must take place via the cable end or the M12 connector.

1 4

Ordering details

Actuating magnet

Spacer

BPS 33

BN 31/33

The actuators for the magnetic safety sensors must be ordered separately.

2 3

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

TG...-A

150

8,5

200

• Door handle switch

• Integrated AS-Interface

• AS-Interface LED status display

• AS-Interface M12 connector

• Enabling button

• Coloured signal LEDs (optional)

• Protection class IP 65

4

Technical data

Standards: EN 50295

EN 60947-5-1

EN 954-1

PA + POM Enclosure:

AS-Interface connection type:

Protection class:

AS-Interface operating voltage: connector M12 x 1

IP 65 reverse-polarity proof

AS-Interface operating current:

) 50 mA

AS-Interface specification : Profile S-B.A

IO-Code 0xB

ID-Code 0xA

ID-Code2 0xE

Outputs:

26.5 ... 31.6 VDC, via AS-Interface,

Inputs:

Data bits

D0

D1

Function

LED 1 (G)

LED 2 (R)

Data bits

D2

Function

NO contact 1

D3 NO contact 2

(optional)

Input module address: default on address 0, programmable via the

AS-Interface Master or

Hand-held programming device

Indications: AS-Interface: voltage LED green communication LED red

EMC rating: conforming to

EMC Directive

– 20 °C … + 60 ºC Ambient temperature:

Storage and transport temperature: – 25 °C … + 85 ºC

S

R

O R

Approvals

C D

C

Ordering details

TG-S GR xx-A

Further devices on request.

Note

A separate address jack is not available as an option. The addressing must take place via the cable end or the M12 connector.

1 4

2 3

M12 connector:

1: AS-Interface +

2: spare

3: AS-Interface –

4: spare

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688

27

AS-Interface Safety at Work

ASF 2 CC

51

• Input module

• 2 safe inputs for mechanical contacts

• Cross-wire monitoring

• Cage clamp terminals for safety device connection

• LED function display

• IDC technology for

AS-Interface flat cable

• Protection class IP 67

66

102

80

S

R

O R

Technical data

Standards:

Enclosure:

AS-Interface connection type:

Cage clamp terminals:

AS-Interface operating voltage:

Protection class:

AS-Interface operating current:

Inputs:

Input signal:

AS-Interface specification:

Inputs:

Parameter bits:

Input module address:

Indications:

EMC rating:

Ambient temperature:

Storage and transport temperature:

1

1

2

2

EN 50295, EN 954-1 black

IDC to the flat cable AS-Interface max. 2,5 mm

2

(incl. conductor ferrules)

26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof

IP 67

< 70 mA

2 safe inputs for mechanical contacts, monitored for cross-wired circuit, cable length < 30 m

„S+1, S+2“: le < 10 mA, pulsed

Profile: S-0.B

IO-Code: 0x0

ID-Code: 0xB

ID-Code2: 0xE on off on off

D0/D1 = dynamic code transmission

D0/D1 = static code “00”

D2/D3 = dynamic code transmission

D2/D3 = static code “00”

P0

P1

P2

P3 not used default on address 0, programmable via the AS-Interface Master or Hand-held programming device

AS-Interface: not used not used not used

Switching condition: voltage LED green communication LED red

LED yellow conforming to EMC Directive

– 25 °C … + 60 ºC

– 25 °C … + 85 ºC

Approvals

F

C

Ordering details

ASF 2 CC

Note

The safe AS-Interface input module offers two universal safety relevant inputs for mechanical contacts. The safe switches are connected to cage-clamp terminals inside the module housing.

The signal voltage is supplied by the module itself.

The two safe input channels are cross-wire monitored

The base module is the electro-mechanical link between the AS-Interface flat cable and the user module (i.e. ASF 2CC).

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

Note

• The wiring diagram is shown with guard doors closed and in de-energised condition.

Wiring diagram

S+1 RES S-1 S-2 RES S+2

• Please note that for the correct use of the input module there must be two jumpers present (1+2 and 5+6, see electrical connection).

• Monitoring a sliding guard door using two position switches with safety function.

The NC contact must have positive break when the guard door is opened.

Inputs

2 1

S+1 RES S-1 S-2 RES S+2

Inputs

2 1

S

R

O R

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688

29

AS-Interface Safety at Work

ASF KM1

¤ 9,6

26

80

36

Technical data

Standards:

U e

:

I e

:

AS-Interface specification:

AS-Interface connection type:

EN 50295

26,5 … 31,6 V

(according to AS-Interface specification) max. 2 A

EMS

Protection class:

2 flat cables

AS-Interface (IDC)

IP 67 to EN60529

Ambient temperature:

(only in combination with ASF 2 CC)

– 25 °C … + 60 ºC

Storage and transport temperature:

Special features:

– 25 °C … + 85 ºC

2 parallel cable channels for various T- and

Mounting:

Cross-junctions top hat section rail or screw mounting

36 26

¤ 5,8

• Base module

• Base module without address jack

• AS-Interface interface for user module

• Connection of AS-Interface flat cable

• Top hat section rail or screw mounting

S

R

O R

Approvals

Ordering details

ASF KM 1

Note

The base module is the electro-mechanical link between the AS-Interface flat cable and the user module (i.e. ASF 2CC).

Note

AS-i

AS-i

-

+

-

+

+ -

Contacts to module

Phone: 905-738-6688 www.ipecautomation.com

AS-Interface Safety at Work

ASF PM

• Hand-held programming device

• Addressing and Programming up to a maximum of 62 Slaves (A/B-Slaves)

• Read/write operation of slave data

• Displaying the IO-code

• Read/write operation of parameter data

• Displaying the address mode / ID-code

• Displaying the peripheral fault flags

• Determining the slave address

• Re-addressing with checking

• Slave connection is short-circuit and overload proof

• Mech. connection with the help of the universal adapter

• Battery charger included with delivery

S

R

O R

Technical data Note

Interface:

Operating device:

Operating duration:

Power supply:

Display:

Keyboard:

Protection class:

Ambient temperature:

Storage and transport temperature:

Dimensions:

AS-Interface, short-circuit- and overload-proof

230 VAC, plug-in charging unit, included in the delivery package

8 h or > 250 read/write cycles with fully charged batteries battery mode, charging time before use about 14 h

LC-display

5 keys, membrane keys

IP 20

0 °C … + 55 ºC

– 20 °C … + 55 ºC

80 x 34 x 214 mm

The LCD displays the address, the operating mode or an error code. The AS-Interface hand held programming device will be switched on by pressing the button “ADR”. It shuts down independently after about one minute when not in use.

• Pressing the “ADR” button causes the current slave address to be displayed

• The two keys “ B “ and “ ? “ can be used to select the programmable address from the address ring (i.e. 0 ...31, 0 ...31A, 0 ...31B)

• A short key stroke causes the page to turn stepwise, whereas holding down the key causes the pages to scroll continuously

(0.5s per address)

• Pressing the “PRG”-key causes the new address to be loaded into the slave

• The correct programmed address is automatically displayed after about 0.5s

• Holding down “ADR” and “PRG” simultaneously will automatically set back the slave address to zero

• Other key combinations do not trigger any further action

Approvals

C

Ordering details

ASF PM

Note

The LCD displays the address, the operating mode or an error code.

„ B “ button = increments slave address

„MODE“ button = changes the working mode

„ ? “ button = decrements slave address

„PRG“ button = programming of the new slave address

„ADR“ button = reading a slave address / switches on the device

Error messages

F1: AS-Interface overload

F2: Slave not found

F3: Programming error

F4: Destination address busy

F5: Zero address already occupied

F6: Standard slave found instead of an extended slave

F7: Extended slave found instead of a standard slave

F8: Reception error

LOBAT = Recharge batteries !

After the first indication approx. 30 read/write operation are still possible.

Load the accumulator only with the charger included within this delivery.

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688

31

Notizen

Phone: 905-738-6688 www.ipecautomation.com

More Details

Detailed technical information at: www.schmersal.com

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

German agencies

International agencies

Stammhaus

K.A. Schmersal GmbH

Industrielle Sicherheitsschaltsysteme

Postfach 24 02 63, 42232 Wuppertal

Möddinghofe 30

42279 Wuppertal

Telefon: +49-(0) 2 02-64 74-0

Telefax: +49-(0) 2 02-64 74-1 00

E-Mail: [email protected]

Internet: www.schmersal.com

01 Hamburg

K.A. Schmersal GmbH

Geschäftsstelle Hamburg

Zunftstraße 8

21244 Buchholz i.d.N.

Telefon: +49-(0) 41 81-9 22 0-0

Telefax: +49-(0) 41 81-9 22 0-20

E-Mail: [email protected]

02 Berlin

KSA Komponenten der Steuerungsund Automatisierungstechnik GmbH

Buchholzer Str. 62-65

13156 Berlin

Telefon: +49-(0) 30-47 48 24 00

Telefax: +49-(0) 30-47 48 24 05

E-Mail: [email protected]

Internet: www.ksa-gmbh.de

03 Hannover

ELTOP GmbH

Robert-Bosch-Str. 8

30989 Gehrden

Telefon: +49-(0) 51 08-92 73 20

Telefax: +49-(0) 51 08-92 73 21

E-Mail: [email protected]

Internet: www.eltop.de

04 Münster

K.A. Schmersal GmbH

Geschäftsstelle Münster

Am Vechte Ufer 22

48629 Metelen

Telefon: +49-(0) 25 56-9 38 30

Telefax: +49-(0) 25 56-93 83 73

E-Mail: [email protected]

05 Köln

Stollenwerk

Technisches Büro GmbH

Scheuermühlenstr. 40

51147 Köln

Telefon: +49-(0) 22 03-9 66 20-0

Telefax: +49-(0) 22 03-9 66 20-30

E-Mail: [email protected]

14 Ruhrgebiet

K W S Elektronik Schumacher

Saarstr. 19a

53919 Weilerswist

Telefon: +49-(0) 22 54-33 80

Telefax: +49-(0) 22 54-18 58

E-Mail: [email protected]

12 Siegen

Siegfried Klein

Elektro-Industrie-Vertretungen

Schloßblick 38

57074 Siegen

Telefon: +49-(0) 2 71-67 78

Telefax: +49-(0) 2 71-67 70

E-Mail: [email protected]

16 Frankfurt

K.A. Schmersal GmbH

Geschäftsstelle Frankfurt

Kilianstädter Straße 38

61137 Schöneck

Telefon: +49-(0) 61 87-9 09 56-0

Telefax: +49-(0) 61 87-9 09 56-6

E-Mail: [email protected]

Argentina - Argentinien

Hellermann Tyton

Monteagudo Street # 760

(B1672 AFP), Villa Lynch

1672 Buenos Aires

Telefon: +54-11-47 54 54 00

Telefax: +54-11-47 52 03 74

E-Mail: [email protected]

Australia - Australien

NHP Electrical Engineering

Products Pty. Ltd.

43 - 67 River Street

PO Box 199

Richmond 3121

Melbourne, Victoria

Telefon: +61-(0) 3-94 29 29 99

Telefax: +61-(0) 3-94 29 10 75

E-Mail: [email protected]

Internet: www.nhp.com.au

Austria - Österreich

AVS-Schmersal Vertriebs Ges. m.b.H.

Biróstraße 17

1232 Wien

Telefon: +43-(0) 1-6 10 28

Telefax: +43-(0) 1-6 10 28-1 30

E-Mail: [email protected]

Internet: www.avs-schmersal.co.at

Belgium - Belgien

Schmersal Belgium NV/SA

Nieuwlandlaan 16B

Industriezone B413

3200 Aarschot

Telefon: +32-(0) 16-57 16 18

Telefax: +32-(0) 16-57 16 20

E-Mail: [email protected]

Internet: www.schmersal.be

Brazil - Brasilien

ACE Schmersal

Eletroeletrônica Industrial Ltda.

Rodovia Boituva-Porto Feliz, Km 12

Vila Esplanada – CEP: 18550-000

Boituva – SP

Telefon: +55-(0) 15-32 63-98 66

Telefax: +55-(0) 15-32 63-98 90

E-Mail: [email protected]

Internet: www.aceschmersal.com.br

Chile - Chile

NDU Ingeneria

Santa Elisa 498

7160269 La Cisterna

Santiago de Chile

Telefon: +56-2-5 26-66 46

Telefax: +56-2-5 26-50 46

E-Mail: [email protected]

Colombia - Kolumbien

Cimpex Ltda.

Apartado Aereo 2429

Medellin

Telefon: +57-4-2 51-59 72

Telefon: +57-4-2 51-59 87

Telefax: +57-4-2 51-46 08

E-Mail: [email protected]

Costa Rica - Costa Rica

Euro-Tec, S.A.

Apartado Postal 477

1250 Escazú

San José

Telefon: +5 06-2 20-28 08

Telefon: +5 06-3 84-78 69

Telefax: +5 06-2 96-15 42

E-Mail: [email protected]

PR China - VR China

Schmersal Industrial Switchgear Co. Ltd.

Central Plaza 1001

Huang Pi Bei Road 227

200003 Shanghai

Telefon: +86-21-63 75 82 87

Telefax: +86-21-63 75 82 97

E-Mail: [email protected]

Internet: www.schmersal.com.cn

Czech Republic -

Tschechische Rebublik

Mercom Componenta spol. s.r.o.

Ruská 67

100 00 Praha 10

Telefon: +4 20-(0) 2-67 31 46 40

Telefon: +4 20-(0) 2-67 31 46 41

Telefax: +4 20-(0) 2-71 73 32 11

E-Mail: [email protected]

Denmark - Dänemark

Schmersal Danmark A/S

Lindegårdsvej 17A

2920 Charlottenlund

Telefon: +45-70 20 90 27

Telefax: +45-70 20 90 37

E-Mail: [email protected]

Internet: www.schmersal.dk

Finland - Finnland

Advancetec Oy

Malminkaari 10B

PO Box 149

00701 Helsinki

Telefon: +3 58-(0) 9-3 50 52 60

Telefax: +3 58-(0) 9-35 05 26 60

E-Mail: [email protected]

Internet: www.advancetec.fi

France - Frankreich

Automatisme et Contrôle

8, rue Raoul Follereau, BP 18

38180 Seyssins

Telefon: +33-4 76 84 23 20

Telefax: +33-4 76 48 34 22

E-Mail: [email protected]

Internet: www.automatisme-et-controle.fr

Greece - Griechenland

Kalamarakis Sapounas S.A.

Ionias & Neromilou

PO Box 46566

13671 Chamomilos Acharnes

Athens

Telefon: +30-(0) 1-2 40 60 00-6

Telefax: +30-(0) 1-2 40 60 07

E-Mail: [email protected]

Honduras - Honduras

Lusitana Int´I,

Distribuciones - Represantaciones

Apdo. Postal # 783

21105 San Pedro Sula

Telefon: +5 04-6 69-14 46

Telefax: +5 04-6 69-14 46

Hungary - Ungarn

NTK Ipari-Elektronikai és

Kereskedelmi Kft

Mészáros L. u. 5.

9023 Györ

Telefon: +36-(0) 96-52 32 68

Telefax: +36-(0) 96-43 00 11

E-Mail: [email protected]

Internet: www.ntk-kft.hu

India - Indien

Arihant Electricals

24/4866, Ansari Road

Darya Ganj, Sheel Tara House

102222 New Delhi

Telefon: +91-11-23 26 21 76

Telefax: +91-11-23 27 35 54

E-Mail: [email protected]

Phone: 905-738-6688 www.ipecautomation.com

08 Saarland

Herbert Neundörfer

Werksvertretungen

Saargemünder Str. 68a

66130 Güdingen

Telefon: +49-(0) 6 81-87 54 54

Telefax: +49-(0) 6 81-87 54 53

E-Mail: [email protected]

Internet: www.herbert-neundoerfer.de

10/

15

Bayern Süd

Ing. Adolf Müller GmbH

Industrievertretungen

Elly-Staegmeyr-Str. 15

80999 München

Telefon: +49-(0) 89-8 12 60 44

Telefax: +49-(0) 89-8 12 69 25

E-Mail: [email protected]

19 Leipzig

K.A. Schmersal GmbH

Geschäftsstelle Leipzig

Nonnenstraße 11c

04229 Leipzig

Telefon: +49-(0) 3 41-4 87 34 50

Telefax: +49-(0) 3 41-4 87 34 51

E-Mail: [email protected]

11 Stuttgart

Gerhard Schützinger

Labor-Schütz GmbH

Industrievertretungen

Postfach 81 05 69, 70522 Stuttgart

Eichwiesenring 6

70567 Stuttgart

Telefon: +49-(0) 7 11-7 15 46-0

Telefax: +49-(0) 7 11-7 15 46-18

E-Mail: [email protected]

Internet: www.schuetzinger.de

09 Bayern Nord

K.A. Schmersal GmbH

Geschäftsstelle Nürnberg

Beethovenstr. 14

91074 Herzogenaurach

Telefon: +49-(0) 91 32-73 70 00

Telefax: +49-(0) 91 32-73 48 44

E-Mail: [email protected]

Indonesia - Indonesien

P.T. Wiguna Sumber Sejahtera

JI. Kesehatan Raya No. 36

Jakarta Pusat 10160

Telefon: +62-(0) 21-34 83 42 30

Telefax: +62-(0) 21-34 83 42 31

E-Mail: [email protected]

Internet: www.wiguna.co.id

Israel - Israel

A.U. Shay Ltd.

23 Imber St. Kiriat. Arieh.

P.O. Box 10049

Petach Tikva

Telefon: +9 72-3-9 23 36 01

Telefax: +9 72-3-9 23 46 01

E-Mail: [email protected]

Italy - Italien

Schmersal Italia s.r.l.

Via Molino Vecchio, 206

25010 Borgosatollo, Brescia

Telefon: +39-0 30-2 50 74 11

Telefax: +39-0 30-2 50 74 31

E-Mail: [email protected]

Internet: www.schmersal.it

Japan - Japan

Elan-Schmersal Japan Branch Office

3-39-8 Shoan, Suginami-ku,

Tokyo 167-0054

Telefon: +81-(03)-3247-0519

Telefax: +81-(03)-3247-0537

E-Mail: [email protected]

Korea - Korea

MEC Manhani Electric Co. Ltd.

576-8, Bisan-2dong

Dongan-Ku

Anyang-City

Kyungi-Do 431-821

Telefon: +82-(0) 31-4 63-33 00

Telefax: +82-(0) 31-4 63-33 98

Telefax: +82-(0) 31-4 63-33 99

E-Mail: [email protected]

Malaysia - Malaysia

Ingermark (M) SDN.BHD

No. 29, Jalan KPK 1/8

Kawasan Perindustrian Kundang

48020 Rawang, Selangor Darul Ehsan

Telefon: +6 03-60-34 27 88

Telefax: +6 03-60-34 21 88

E-Mail: [email protected]

Netherlands - Niederlande

Hatenboer Elektro BV

Postbus 200

2170 AE Sassenheim

Telefon: +31-(0) 2 52-21 90 12

Telefax: +31-(0) 2 52-23 29 38

E-Mail: [email protected]

Internet: www.hatenboer.com

Norway - Norwegen

Schmersal Nordiske

Hoffsveien 92

0377 Oslo

Telefon: +47-22 06 00 70

Telefax: +47-22 06 00 80

E-Mail: [email protected]

Internet: www.schmersal.se

Paraguay - Paraguay

Brasguay S.R.L.

Ruta Internacional, 07, Km1

Mingua Guazu

Telefon: +5 95-6 44-2 04 18

Telefax: +5 95-6 44-2 05 77

E-Mail: [email protected]

Poland - Polen

Schmersal - Polska Sp.j.

ul. Kremowa 65A

02-969 Warszawa

Telefon: +48-(0) 22-8 16 85 78

Telefon: +48-(0) 22-8 16 85 79

Telefax: +48-(0) 22-8 16 85 34

E-Mail: [email protected]

Portugal - Portugal

K.A. Schmersal GmbH

Sucursal em Portugal

Av. das Descobertas, 15-2° D

Quinta do Infantado

2670-383 Loures

Telefon: +3 51-21-9 83 92 83

Telefax: +3 51-21-9 83 19 37

E-Mail: [email protected]

Internet: www.schmersal.pt

Serbia/Montenegro - Serbien

Tipteh d.o.o. Beograd

Bulevar AVNOJ-a45D, lokal 18

11070 Novi Beograd,

Serbien / Montenegro

Telefon: +3 81-11-3 13 10 57

Telefax: +3 81-11-3 01 83 26

E-mail: [email protected]

Internet: www.tipteh.co.yu

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

05

04

14

12

16

08

11

03

01

09

10/15

19

02

Singapore - Singapur

Tong Sim Marine & Electric Co.

46 Kaki Bukit Crescent

Kaki Bukit Techpark 1

Singapore 416269

Telefon: +65-67 43 31 77

Telefax: +65-67 45 37 00

E-Mail: [email protected]

Slovenia - Slowenien

Tipteh d.o.o.

Ulica Ivana Roba 21

1000 Ljubljana

Telefon: +386-1-2 00 51 50

Telefax: +386-1-2 00 51 51

E-Mail: [email protected]

Spain - Spanien

Forn Valls S.A.

c/Milanesado, 2 tda

08017 Barcelona

Telefon: +34-9 32-03 41 33

Telefon: +34-9 32-04 05 44

Telefax: +34-9 32-05 54 67

E-Mail: [email protected]

Internet: www.fornvalls.com

South Africa - Südafrika

A+A Dynamic Distributors (Pty) Ltd.

3 Ruarch Street

Park Central Johannesburg

PO Box 38247

2016 Booysens

Telefon: +27-11-4 93 50 22

Telefax: +27-11-4 93 07 60

E-Mail: [email protected]

Sweden - Schweden

Schmersal Nordiska AB

Klockarns Väg 1

43533 Mölnlycke

Telefon: +46-(0) 31-3 38 35 00

Telefax: +46-(0) 31-3 38 35 35

E-Mail: [email protected]

Internet: www.schmersal.se

Switzerland - Schweiz

Schmersal Schweiz AG

Freilagerstr. 25

8047 Zürich

Telefon: +41-(0) 43-3 11 22 33

Telefax: +41-(0) 43-3 11 22 44

E-Mail: [email protected]

Taiwan - Taiwan

Leader Camel Enterprise Co., Ltd.

No. 453-7, Pei Tun Rd.

Taichung, Taiwan

Telefon: +886-4-22 41 32 92

Telefax: +886-4-22 41 29 23

E-Mail: [email protected]

Internet: www.leadercamel.com.tw

Thailand - Thailand

M. F. P. Engineering Co. Ltd.

64-66 Buranasart Road

Sanchaoporsva

Bangkok 10200

Telefon: +66-2-2 26 44 00

Telefax: +66-2-2 25 67 68

E-Mail: [email protected]

Turkey - Türkei

BETA Elektrik Sanayi Ve Ticaret

Günes Han. No. 66/7

80020 Karaköy / ISTANBUL

Telefon: +90-212-253 99 14

+90-212-253 99 15

Telefax: +90-212-253 54 56

E-Mail: [email protected]

Internet: www.betaelektrik.com

UK - Großbritannien

Schmersal UK Ltd.

Unit 1, Beauchamp Business Centre

Enigma Park

Worcs WR14 1GL, Malvern

Telefon: +44-(0) 16 84-57 19 80

Telefax: +44-(0) 16 84-56 02 73

E-Mail: [email protected]

Internet: www.schmersal.co.uk

USA - USA

Schmersal Inc.

660 White Plains Road

Suite 160

Tarrytown, NY 10591

Telefon: +1-(0) 9 14-3 47-47 75

Telefax: +1-(0) 9 14-3 47-15 67

E-Mail: [email protected]

Internet: www.schmersalusa.com

Venezuela - Venezuela

Petro System C.A.

Av. 12 entre 7 y 8 Transv. Qta. Roysbel

Altamira No. 3405

Caracas

Telefon: +58-212-9 63 53 46

+58-212-9 61 40 76

E-Mail: [email protected]

Phone: 905-738-6688

35

K.A. Schmersal GmbH

Industrielle Sicherheitsschaltsysteme

Möddinghofe 30

D-42279 Wuppertal

Postfach 24 02 63

D-42232 Wuppertal

Telefon +49 - (0)2 02 - 64 74 - 0

Telefax +49 - (0)2 02 - 64 74 - 1 00

E-Mail [email protected]

Internet http://www.schmersal.com

IPEC Industrial Controls Ltd.

17-109 Fernstaff Court, Concord, Ont. L4K 3M1

Phone: 905-738-6688 www.ipecautomation.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement