Craftsman | 315.101260 | Operator`s manual | Craftsman 315.101260 Operator`s manual

PERATOR'S
MAN
AL
®
19.2 VOLT RADIO
Model No.
315.101260
AM/FM/AUX/
WEATHER
iii
BATTERIES AND CHARGERS
SOLD SEPARATELY
WARNING:
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this
product.
Craftsman
Consumer
Sears, Roebuck
Helpline:
1-800-932-3188
and Co., 3333 Beverly Rd., Hoffman
Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
C
987000-147
06-27-07 (REV:01)
Save this
manual
for future
reference
•
Warranty ..........................................................................................................................................................................
2
•
Introduction .....................................................................................................................................................................
2
•
General Safety Rules .......................................................................................................................................................
3
•
Specific Safety Rules .......................................................................................................................................................
4
•
Safety Rules for Charger .................................................................................................................................................
5
•
Symbols ........................................................................................................................................................................
•
Features ...........................................................................................................................................................................
8
•
Assembly .........................................................................................................................................................................
9
•
Operation ....................................................................................................................................................................
9-13
•
Maintenance .............................................................................................................................................................
14-15
•
Exploded View and Parts List ........................................................................................................................................
•
Parts Ordering/Service
.....................................................................................................................................
ONE-YEAR FULL WARRANTY
ON CRAFTSMAN
6-7
16
Back Page
TOOL
If this Craftsman tool fails to give complete satisfaction within one year from date of purchase, RETURN iT TO ANY
SEARS STORE OR OTHER CRAFTSMAN OUTLET iN THE UNITED STATES FOR FREE REPLACEMENT.
If this Craftsman tool is used for commercial
purchase.
or rental purposes, this warranty applies for only 90 days from the date of
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
This product has many features for making its use more pleasant and enjoyable. Safety, performance,
have been given top priority in the design of this product making it easy to maintain and operate.
A
and dependability
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
iMPORTANT SAFETY iNSTRUCTiONS
PRODUCT
,_k
WARNING!
READ AND UNDERSTAND ALL
INSTRUCTIONS.
Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious personal injury.
KEEP THESE
INSTRUCTIONS
HEED ALL WARNINGS
FOLLOW
WORK
ALL INSTRUCTIONS
AREA
[] Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
[] Do not operate products in explosive atmospheres,
such as in the presence of flammable liquids,
gases, or dust. Products create sparks which may
ignite the dust or fumes.
ELECTRICAL
SAFETY
[] A bakery operated product
or a separate battery pack
with the specified charger
that may be suitable for one
a risk of fire when used with
with integral batteries
must be recharged only
for the battery. A charger
type of battery may create
another battery.
[] Use battery operated product only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire.
[] Use battery
MODEL
315.101260
PERSONAL
only with charger
listed.
BATTERY PACK
CHARGER
130279005
Model No. 1425301
(item No. 9_11375)
(item No. 9_11041)
130279003
Model No. 315.115730
(item No. 140301003)
SAFETY
[] Avoid accidental starting. Be sure switch is in
the locked or off position before inserting battery
pack. Carrying products with your finger on the switch
or inserting the battery pack into a product with the
switch on invites accidents.
[] Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enabJe better
control of the product in unexpected situations.
[] Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
product in unexpected situations.
USE AND
CARE
[] Do not use product if switch does not turn it on or
off. A product that cannot be controlled with the switch
is dangerous and must be repaired.
[] Disconnect battery pack from product or place the
switch in the locked or off position before making
any adjustments,
changing accessories,
or storing
the product. Such preventive safety measures reduce
the risk of starting the product accidentally.
[] When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
[] Keep the radio and its handle dry, dean and free
from oil and grease. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleumbased products, or any strong solvents to clean your
radio. Following this rule will reduce the risk of loss of
control and deterioration of the enclosure plastic.
[] Do not use this apparatus
near water.
[] Clean only with dry cloth.
[] Do not block any ventilation openings. Install in
accordance with the manufacturer's
instructions.
[] Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
[] Only use attachments/accessories
manufacturer.
specified
by the
SERVICE
[] Product service must be performed only by
qualified repair personnel. Service or maintenance
performed by unqualified personnel may result in a risk
of injury.
[] When servicing a product, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance
instructions may create a risk of shock or injury.
[] Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
iMPORTANT SAFETY iNSTRUCTiONS
[] Know your product. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to
this product. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
[] Battery products do not have to be plugged into
an electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery product or when
changing accessories.
Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
[] Do not place battery products or their batteries
near fire or heat. This will reduce the risk of explosion
and possible injury.
[] Do not crush, drop or damage battery pack. Do
not use a battery pack or charger that has been
dropped or received a sharp blow. A damaged
battery is subject to explosion. Properly dispose of a
dropped or damaged battery immediately.
[] Batteries vent hydrogen gas and can explode in
the presence of a source of ignition, such as a pilot
light. To reduce the risk of serious personal injury,
never use any cordless product in the presence of
open flame. An exploded battery can propel debris and
chemicals. If exposed, flush with water immediately.
[] Do not charge battery product in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
[] For best results, your battery product should be
charged in a location where the temperature is
more than 50°F but less than 100°F. To reduce the
risk of serious personal injury, do not store outside or in
vehicles.
[] Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
[] To reduce the risk of personal injury and electric
shock, the product should not be played with or
placed where small children can reach it.
[] To reduce the risk of electric
to water or rain.
[]
shock, do not expose
If the power supply cord is damaged, it must be
replaced only by the manufacturer or by an authorized
service center to avoid risk.
A
WARNING!
READ AND UNDERSTAND ALL
INSTRUCTIONS. Failure to follow all instructions
listed below, may result in electric shock, fire and/or
serious personal injury.
[] Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, battery, and product using battery to prevent
misuse of the products and possible injury or damage.
_1_
CAUTION:
To reduce the risk of electric shock
or damage to the charger and battery, charge
only nickel-cadmium rechargeable batteries as
specifically designated on your charger. Other
types of batteries may burst, causing personal
injury or damage.
[] Do not use charger outdoors or expose to wet or
damp conditions. Water entering charger will increase
the risk of electric shock.
[] Use of an attachment not recommended
or sold
by the battery charger manufacturer
may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
[] Do not abuse cord or charger. Never use the cord to
carry the charger. Do not pull the charger cord rather
than the plug when disconnecting from receptacle.
Damage to the cord or charger could occur and create
an electric shock hazard. Replace damaged cords
immediately.
[] Make sure cord is located so that it will not
be stepped on, tripped over, come in contact
with sharp edges or moving parts or otherwise
subjected to damage or stress. This will reduce the
risk of accidental falls, which could cause injury, and
damage to the cord, which could result in electric
shock.
[] Keep cord and charger from heat to prevent
damage to housing or internal parts.
[] Do not let gasoline, oils, petroleum-based
products,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
I
=
2.
3.
PC
SAVE THE
[] An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on charger.
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere rating
of charger as specified below:
Cord Length (Feet)
25'
50'
100'
Cord Size (AWG)
16
16
16
NOTE: AWG = American Wire Gauge
[] Do not operate charger with a damaged cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
[] Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way. Take it to an authorized serviceman for electrical
check to determine if the charger is in good working
order.
[] Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
[] Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of
electric shock.
[] Disconnect charger from the power supply when
not in use. This will reduce the risk of electric shock
or damage to the charger if metal items should fall into
the opening. It also will help prevent damage to the
charger during a power surge.
[] Risk of electric shock. Do not touch uninsulated
portion of output connector or uninsulated battery
terminal.
[] Save these instructions.
Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also to prevent misuse of the product and
possible injury.
NT SAFETY INSTRUCTION
E IN }TR CTIO
This manual contains important safety and operating instructions for battery charger 1425301 and 11 5730.
Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and
product using battery.
CAUTION: To reduce the risk of injury, charge only nickel-cadmium rechargeable batteries. Other types of batteries
may burst, causing personal injury or damage.
Someof the followingsymbolsmaybe usedon this product.Pleasestudythemandlearntheir meaning.Proper
interpretation
ofthesesymbolswill allowyouto operatetheproductbetterandsafer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
mz
Hertz
Frequency (cycles per second)
W
Watt
Power
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic
no
No Load Speed
Rotational speed, at no load
[]
Class II Construction
Double-insulated
.../min
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
@
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Read The Operator's Manual
To reduce the risk of injury, user must read and understand
operator's manual before using this product.
Eye Protection
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Safety Alert
Precautions that involve your safety.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
Hot Surface
To reduce the risk of injury or damage, avoid contact with any hot
surface.
min
O
,ik
@
@
@
@
of current
construction
Thefollowingsignalwordsandmeanings
areintendedto explainthe levelsof riskassociatedwiththis product.
SYMBOL
_1_
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
A
SERVICE
Servicing requires extreme care and knowledge and
should be performed only by a qualified service technician. For service we suggest you return the product to
your nearest SEARS PARTS AND REPAIR SERVICE
CENTER for repair. When servicing, use only identical
replacement parts.
_
WARNING:
To avoid serious personal injury, do
not attempt to use this product until you read thoroughly and understand completely the operator's
manual. If you do not understand the warnings and
instructions in the operator's manual, do not use this
product. Call the Craftsman Consumer Helpline at
1-800-932-3188 for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and, when needed, a full face shield. We recommend
Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
Always use eye protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
PRODUCT
SPECIFICATIONS
Radio Voltage ..................................................
FM Tuner .................................................
AM Tuner ....................................................
19.2 Volt DC
87.5 - 108.0 MHz
520- 1710 KHz
Weather Band ............................ All 7 Weather Frequencies
used by the National Weather Service
Charger Input ....................................
120 V, 60 Hz, AC only
Charge Rate .............................................................
ANTENNA
DIGITALDISPLAY
MODE
BUTTON
1 hour
AUXILIARY
INPUTJACK
ON /OFF /
VOLUME KNOB
AUXiLiARY
CABLE
TUNE/ SEEK
SELECTOR
ACCESSORY
DEVICEHOLDER
Fig. 1
KNOW
AMPLiFiER
YOUR RADIO
See Figure 1.
The safe use of this product requires an understanding
of the information on the product and in this operator's
manual as well as a knowledge of the project you are
attempting. Before use of this product, familiarize yourself
with all operating features and safety rules.
ACCESSORY
DEVICE
HOLDER
An accessory device holder is located on the back of the
radio for holding small music devices such as MP3
players.
ADJUSTING
TELESCOPING
The radio can be used as an amplifier for MP3 players,
CD players, and other audio devices using the supplied
auxiliary cable.
DIGITAL
DISPLAY
The radio channel and mode can be viewed on the digital
display which illuminates when the radio is turned on.
TUNE/SEEK
SELECTOR
The tune/seek selector allows you to manually search
through each FM and AM radio channel or directly skip to
receivable radio channels.
ANTENNA
The antenna can adjust to pick up radio stations and can
be replaced if necessary.
WEATHER
BAND
The radio can receive all seven weather frequencies
by the National Weather Service.
used
UNPACKING
This product has been shipped completely assembled.
WARNING:
If any parts are damaged or missing
do not operate this product until the parts are replaced. Failure to heed this warning could result in
serious personal injury.
[] Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing
list are included.
[] Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
A
[] Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
[] If any parts are damaged or missing, please call
1-800-932-3188 for assistance.
PACKING
LIST
19.2 Volt Radio
WARNING:
Do not attempt to modify this product
or create accessories not recommended for use with
this product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
A
WARNING:
To prevent accidental starting that
could cause serious personal injury, always remove
the battery pack from the product when assembling
parts.
Auxiliary Cable
Operator's Manual
A
LED FUNCTIONS
WARNING:
Do not allow familiarity with products to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
A
A
BE ON TO INDICATE STATUS
AND BATTERY PACK:
OF
[] Red LED on = Fast charging mode.
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating products.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this
product. The use of attachments or accessories not
recommended can result in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
[] Listening to FM radio, AM radio, Weather Band
Broadcasts
[] Amplifying
devices
LED WiLL
CHARGER
OF CHARGER
MP3 players, CD players, and other audio
CAUTION: If at any point during the charging
process none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the
product. DO NOT insert another battery. Return the
charger and battery to your nearest Sears or other
qualified service center for service or replacement.
[] Green LED on = Fully charged and in maintenance
charge mode.
[] Green LED on = When battery pack is inserted into
charger, indicates hot battery pack or that battery pack
is out of normal temperature range.
[] Yellow and Green LEDs on = Deeply discharged or
defective battery pack.
[] No LED on = Defective charger or battery pack.
CHARGING
THE BATTERY
PACK
The battery pack for this product has been shipped in
a low charge condition to prevent possible problems.
Therefore, you should charge it until the green LED on the
front of the charger comes on.
NOTE: Batteries will not reach full charge the first time
they are charged. Allow several cycles (operation followed
by recharging) for them to become fully charged.
CHARGING
A COOL
BATTERY
PACK
If battery pack is below normal temperature range, the
green LED on charger will come on. Allow battery pack to
reach normal temperature, then the red LED will come on.
NOTE:Ifthe chargerdoesnotchargethebatterypack
undernormalcircumstances,
returnboththe batterypack
andchargerto yournearestSearsor otherqualifiedservicecenterforelectricalcheck.
m Chargethebatterypackonlywiththechargerprovided.
[] Makesurethe powersupplyis normalhousehold
voltage,120volts, 60 Hz, AC only.
BATTERYPACK
SHOWNIN CHARGER
\
CHARGER
[] Connect the charger to the power supply.
[] Place the battery pack in the charger aligning raised rib
on the battery pack with the groove in the charger. See
Figure 2.
RED
LED
[] Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts in the
charger.
GREEN
LED
[] Normally the red LED on charger will come on. This
indicates the charger is in fast charging mode.
.YELLOW
LED
[] Red LED should remain on for approximately 1 hour
then the green LED will come on. Green LED on
indicates battery pack is fully charged and charger is
in maintenance charge mode.
Fig. 2
NOTE: The green LED will remain on until the battery
pack is removed from the charger or charger is
disconnected from the power supply.
CHARGING
[] If both yellow and green LEDs come on, this indicates
a deeply discharged or defective battery pack. Allow
the battery pack to remain in the charger for 15 to 30
minutes. When the battery pack reaches normal
voltage range, the red LED should come on. If the red
LED does not come on after 30 minutes, this may
indicate a defective battery pack that should be
replaced.
A HOT BATTERY
PACK
When using the product continuously, the batteries in the
battery pack will become hot. You should let a hot
battery pack cool down for approximately 30 minutes
before attempting to recharge. When the battery pack
becomes discharged and is hot, this will cause the green
LED to come on instead of the red LED. After 30 minutes,
reinsert the battery pack in the charger. If the green LED
continues to remain on, return battery pack to your
nearest Sears or other qualified service center for checking or replacing.
[] After normal usage, a minimum of 1 hour of charging
time is required to fully recharge battery pack.
NOTE: This situation only occurs when continuous use of
the product causes the batteries to become hot. It does
not occur under normal circumstances. Refer to
CHARGING A COOL BATTERY PACK for normal
recharging of batteries. If the charger does not charge
your battery pack under normal circumstances, return
both the battery pack and charger to your nearest Sears
or other qualified service center for electrical check.
[] The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
[] Do not place the charger and battery pack in an area
of extreme heat or cold. They will work best at normal
room temperature.
NOTE: The charger and battery pack should be placed
in a location where the temperature is more than 50°F
but less than 100°R
[] When batteries become fully charged, unplug the
charger from power supply and remove the battery
pack.
10
TO INSTALL
BATTERY
PACK
TURNING
THE RADIO
ON/OFF
See Figure 3.
• Place the battery pack on the radio.
See Figure 4.
To turn ON: turn the ON/OFF/VOLUME
knob clockwise.
•
To turn OFF: turn the ON/OFF/VOLUME
knob counter-
Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured on the
radio before beginning operation.
clockwise to the OFF position.
MODE
BUTTON
ON/OFF
VOLUME KNOB
BATTERY
PACK
,_
TUNE/SEEK
SELECTOR
LATCHES
Fig. 4
RADIO
MODES
See Figure 4.
There are four mode settings on the radio: FM, AM, AUX,
and the Weather Band setting. To select any of these
settings, turn the radio ON and push the MODE button to
the desired setting.
DEPRESSLATCHESTO
RELEASEBATTERYPACK
TO REMOVE
BATTERY
CONTROLLING
Fig. 3
VOLUME
See Figure 4.
Use the volume level indicator located on the
ON/OFF/VOLUME knob to find the desired volume.
PACK
See Figures 3 - 4.
Place the power switch in the OFF (O} position.
• Turn the ON/OFF/VOLUME
radio volume.
knob clockwise to increase
•
•
Locate latches on side of battery pack and depress
both sides to release battery pack.
Remove battery pack from the radio.
• Turn the ON/OFF/VOLUME
decrease radio volume.
knob counterclockwise
•
11
to
DiGiTAL
DISPLAY
CHANGING
CHANNELS
See Figure 5.
See Figures 4 - 6.
The digital display on the front of the radio illuminates
when the radio is switched ON, displaying the radio mode
and frequency/channel setting. If the battery charge is low,
a flashing low battery indicator will also be displayed.
To change radio channels manually in AM or FM setting,
use the tune button to seek manually or with the seek
feature.
NOTE: Charge battery when low battery indicator begins
to flash. If the radio continues to operate with the low
battery indicator flashing, the radio will drain the battery
until the radio will no longer emit sound and the backlight
and the LCD display will also flash. To avoid deep
discharge, remove the battery pack from the radio and
charge immediately.
[] With the radio set to AM or FM, push the tune/seek
selector up or down and quickly release to manually
change radio channels one frequency at a time.
AM/FM Channels:
[] To change radio channels using the seek feature, push
the tune/seek selector up or down and hold for one
second before releasing to directly skip to receivable
radio channels.
To change channels
in Weather
Band Mode:
[] With the radio set to Weather Band, push the tune/seek
selector up or down and quickly release to manually
change weather band channels one frequency at a
time.
O Q OM.,
BATTERYiNDiCATOR
ANTENNA
FM MODE
FM
! U 2.0M.
L I 1.2!
WEATHERBANDMODE
AM MODE
I
,vx
I
AUX MODE
Fig. 5
Fig. 6
12
NOTE:TheseekfeaturedoesnotworkinWeather
Bandmode.
AUXiLiARY
To use the antenna:
The portable radio can be used as an amplifier for MP3
players, CD players, and other music devices.
[] Raise or lower radio antenna until radio channel can be
heard clearly. The antenna can also be rotated or tilted
to help improve reception for weaker channels.
To use the au×iliary mode:
[] Push the MODE button to select the AUX mode.
WEATHERBAND
CHANNELS
This radio is capable of receiving broadcasts on any one
of seven available National Weather Radio (NWR) broadcast frequencies. The channel numbers displayed when
tuning correspond with the frequencies below:
RADIO DISPLAY
FREQUENCY
Channel 1
162.400 MHz
Channel 2
162.425 MHz
Channel 3
162.450 MHz
Channel 4
162.475 MHz
Channel 5
162.500 MHz
Channel 6
162.525 MHz
Channel 7
162.550 MHz
MODE
See Figure 7.
[] Remove moisture cover protecting the auxiliary input
jack.
[] Plug the auxiliary cable into the auxiliary input jack
above the ON/OFF/VOLUME knob.
[] Plug cable into music device.
[] Turn radio and music device ON.
NOTE: Adjust volume to desired level using either the
radio or music device.
After setting up the radio to amplify an accessory device,
you can use the accessory device holder on the back to
clip the accessory device to the radio.
AUXILIARY
iNPUTJACK
National Weather Radio (NWR) is a nationwide network of
radio stations broadcasting continuous weather information directly from a nearby National Weather Service office. NWR broadcasts National Weather Service warnings,
watches, forecasts, and other hazard information 24 hours
a day. A listing of the National Weather Radio stations
used for specific areas is available on the internet.
AUXILIARY
CABLE
ACCESSORY
DEVICEHOLDER
ACCESSORYDEVICE
(NOT INCLUDED)
ACCESSORYDEVICE
CLIPADAPTER
(NOT INCLUDED)
Fig. 7
13
REPLACINGTHEANTENNA
RADIO
HOUSING
See Figure 8.
ANTENNA
If the radio should need a replacement antenna for any
reason, the attached antenna can easily be removed and
replaced.
[] Insert a phillips head screwdriver
screw slot.
into the antenna
[] Turn the antenna screw counterclockwise
ANTENNA
SCREW
HOLE
to remove.
[] Remove antenna when antenna screw has been
removed.
ANTENNA
SCREW
[] Orient and insert replacement antenna flat end into
antenna mounting hole.
[] Insert the phillips head screw into the antenna screw
hole.
FLATEND
NOTE:ORIENT FLATEND OF
ANTENNA AS SHOWN BEFORE
INSERTINGANTENNA SCREW
[] Turn the antenna screw with the phillips head
screwdriver clockwise to attach and tighten.
ANTENNA
MOUNTINGHOLE
ANTENNA
SCREW
ANTENNA
SCREWHOLE
Fig. 8
14
A
A
A
GENERAL
WARNING:
When servicing, use only identical
Craftsman replacement parts. Use of any other part
may create a hazard or cause product damage.
MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Always wear safety goggles or safety
glasses with side shields when using compressed air
to clean products. If the operation is dusty, also wear
a dust mask.
,_t,. WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc. come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which
may result in serious personal injury.
WARNING:
To avoid serious personal injury, always
remove the battery pack from the product when
cleaning or performing any maintenance.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
BATTERIES
BATTERY
PACK REMOVAL
The battery pack for this product is equipped with nickelcadmium rechargeable batteries. Length of service from
each charging will depend on the type of work you are
doing.
FOR RECYCLING
;B Rc'_ \
AND PREPARATION
To preserve natural resources, please
recycle or dispose of batteries
properly.
This product contains nickel-cadmium
batteries. Local, state or federal
laws may prohibit disposal of nickelcadmium batteries in ordinary trash.
The batteries in this product have been designed to provide maximum trouble-free life. However, like all batteries,
they will eventually wear out. Do not disassemble battery
pack and attempt to replace the batteries. Handling of
these batteries, especially when wearing rings and jewelry,
could result in a serious burn.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
To obtain the longest possible battery life, we suggest the
following:
_
For battery pack storage longer than 30 days:
[] Store battery packs in a "discharged"
Upon removal, cover the battery pack's
terminals with heavy-duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
[] Remove the battery pack from the charger once it is
fully charged and ready for use.
[] Store the battery pack where the temperature
80°R
WARNING:
is below
condition.
15
,-
CRAFTSMAN
I
RADIO - MODEL
NUMBER
315.101260
J
The model
number
will be found
on a plate
motor
housing.
Always
number
in all
correspondence
regarding
yourattached
RADIO to
or the
when
ordering
repair
parts, mention the model
SEE BACK
PAGE FOR PARTS
ORDERING
|
INSTRUCTIONS
4
1
PARTS LIST
Key
No.
Part
Number
Description
1
019021001022
Data Label .......................................................................................................
1
2
019021001039
Antenna Assembly
1
3
019021001001
Logo Label ......................................................................................................
1
019021001038
Auxiliary Connection
1
987000147
Operator's
4
Qty.
..........................................................................................
Cable .............................................................................
Manual (Not Shown)
* Standard Hardware Item - May Be Purchased Locally
16
Download PDF