Asko | DW Outdoor | Service manual | Asko DW Outdoor Service manual

Service manual
Dishwasher - DW Outdoor
Service manual DW Outdoor
2
Service manual
Contents
Type: DW Outdoor
Updates ..................................................................................................................................................................................................................................................4
Introduction .........................................................................................................................................................................................................................................5
Troubleshooting strategy ............................................................................................................................................................................................................6
Types ........................................................................................................................................................................................................................................................7
Technical data......................................................................................................................................................................................................................................8
Component description ...............................................................................................................................................................................................................9
Components and measurement values .........................................................................................................................................................................9
Components and function description ...................................................................................................................................................................... 10
Programs and control unit........................................................................................................................................................................................................ 14
Wiring diagram ......................................................................................................................................................................................................................... 14
Troubleshooting .............................................................................................................................................................................................................................. 16
Dishwashing results ............................................................................................................................................................................................................... 16
Common faults.......................................................................................................................................................................................................................... 16
Water level DW90 .................................................................................................................................................................................................................. 17
Fault indicaton ............................................................................................................................................................................................................................ 18
Tools / Special tools ................................................................................................................................................................................................................. 18
Fault and information codes .............................................................................................................................................................................................. 19
Service menu and settings........................................................................................................................................................................................................ 20
Service and installation ............................................................................................................................................................................................................... 22
Disassembling and reassembling the machine’s casing........................................................................................................................................ 22
Increased working space during service ..................................................................................................................................................................... 25
Overflow guard wiring .......................................................................................................................................................................................................... 26
Service manual DW Outdoor
Updates
Rev
Date
Description
Initials
01
2011-09-29
First version
FH
02
2011-10-20
New document structure
FH
03
2011-11-15
Updated wiring diagram
ISC
4
Service manual DW Outdoor
Introduction
You are holding the Service manual for the DW90 generation of dishwashers.
The DW90 dishwasher series is available in several different models. The DW Outdoor model,
that this guide is focusing on, is designed for outdoor use. The type designation is most important
when identifying a particular machine model. This information can be found on the serial number
plate on the right of the inside of the door, where the machine’s model designation is specified.
TYPE
MODEL
SERIAL NO
The first two digits of the serial number specify the year of manufacture
while the third and fourth digits specify the week of manufacture. The
remaining digits form the sequential number.
It should be easy to service a dishwasher. It is important that you, as a service technician, are
afforded conditions that enable you to work in an efficient and satisfactory way. Our hope is that
this service manual will prove a useful tool in your daily work.
Asko Appliances AB
SE-534 82 Vara
Sweden
OPERATING INSTRUCTIONS
Always have the operating instructions for the machine available during service
5
Service manual DW Outdoor
Troubleshooting strategy
Troubleshooting is an important part of the service call, so we have drawn up a troubleshooting
strategy that describes, in broad terms and step by step, what you need to do to find and diagnose
faults arising in our machines.
• Ask the customer to describe the problem.
• Check whether the customer’s description matches the reported fault.
• Check that the machine is correctly installed:
- Electrical connection
- Drainage
- Water connection
- Machine correctly levelled
Fault
found?
No
Yes
Incorrect installation or external factors that affect performance and functionality (for
example, water pressure, electrical supply, drainage).
The machine operates normally. No deviations can be found. The customer probably
needs to be informed about proper use of the machine. If necessary, also inform the
customer about the warranty conditions and the fact that the customer will be charged
for the service call.
Open the service menu:
1. Check the settings
2. Run a test cycle
3. Note any fault codes
If the above actions do not uncover the fault:
• Conduct general troubleshooting. Use the documentation available at ServiceSaver
(service manuals, service memos, wiring diagrams and other documents).
Fault
found?
Fault
diagnosed?
Yes
Yes
No
Yes
OK?
No
Repair and check
function/safety.
Contact technical support
for assistance.
Carry out the actions
suggested by technical
support.
Satisfied customer!
6
No
Service manual DW Outdoor
Types
DW Outdoor
The machine has 9 set programs, but can be specified with up to 16 programs. The touch buttons
and display are usually found on the top. Certain variants are supplied with a display on the front.
7
Service manual DW Outdoor
Dimensions
Height
US
35” to 35 3/4”
Metric
889-908 mm
Width
24 5/8”
625 mm
Depth (inkl. High loop)
25”
635 mm
Depth W/Handle
27”
686 mm
Depth W/Door open
51 5/8”
1311 mm
Weight (freestanding)
163 lb
74 kg
27"
686 mm
24-5/8"
625 mm
51-5/8"
1311 mm
146 mm to 168 mm
5-3/4" to 6-5/8"
35" to 35-3/4"
889 to 908 mm
25"
635 mm
3-1/2"
89 mm
Door
4-7/8"
124 mm
Technical Data
Connection
1-phase, 120V, 60 Hz, 15 A**
1-phase, 230 V, 50/60 Hz, 10 A/16 A**
Water pressure
0.03–1.0 MPa
0.3–10 kp/cm2
4.3-140 psi
Heating element
1200 W**
1600 W**
Max. rated power
1300 W**
1700 W**
* According to EN 50242 standard.
** See type plate.
8
3-7/8"
98 mm
9-1/2"
241 mm
Service manual DW Outdoor
Component description
Components and measurement values
The specified resistance values apply at room temperature (about 20°C/68°F)
Values within ±10% are considered normal.
Article no. Component
8073779
8083041
8079504
8079505
8078096
8083094
8083095
8078080
8078080
8078082
8078082
8078087
8078089
8079502
8079503
8079500
8079501
8073830
8084147
EMC-filter with inductor
Filter with screwplint
Heating element 1600 W 230 V
Heating element 1200 W 120 V
Thermistor
Combi disp. 230 V
Combi disp. 120 V
Circ.pump 220-240 V 50 Hz,
47 L (12.4 gallon)/min
Circ.pump 220-240 V 50 Hz
Circ.pump 120 V 60 Hz,
47 L (12.4 gallon)/min
Circ.pump 120 V 60 Hz
Drain pump 200-240 V 50 Hz,
16 L (4.2 gallon)/min
Drain pump 120V 60 Hz,
16 L (4.2 gallon)/min
Inlet valve single 200-240 V,
4 L (1 gallon)/min
Inlet valve single 120 V,
4 L (1 gallon)/min
Inlet valve security 220-240 V,
4 L (1 gallon)/min
Inlet valve security 120 V,
4 L (1 gallon)/min
Halogen lamp 5 W/12 V
Thermo Actuator 110-240 V
Measurement
value
Primary winding
680 kohm
1 Mohm
32 ohm
12 ohm
60 kohm
1,32 kohm
285 ohm
115 ohm
Auxiliary winding
260 ohm
Primary winding
31,4 ohm
Auxiliary winding
76 ohm
148 ohm
26 ohm
3,9 kohm
0,95 kohm
2 kohm
0,5 kohm
<10 kohm
0,85-1,2 kohm
* The number is for a complete water softener; replacement salt and mixer valves are not available separately.
9
Service manual DW Outdoor
Component description
Components and function description
Here we describe the function and
specification of the most important
components. Certain components are found
only in more highly specified machines or in
particular markets. See the Troubleshooting
section for fault and information codes.
CU, Control Unit
The CU, or Control Unit, is a unit that functions
as both a control panel and a logic component.
The control panel is fitted with a display and touch
buttons for selecting programs, options and Start/
Stop. The control panel is an integrated part of
the CU and cannot be replaced separately. The
logic component manages functions needed for
dishwashing programs and diagnosis. The CU
has an internal power supply for the logic. In the
event of a fault, the CU can diagnose a number of
components and functions and display fault codes.
To facilitate troubleshooting the service menu
includes a component diagnostics function, which
activates the outputs in a particular sequence.
Accelerometer
The control unit contains an accelerometer, a
sensor that senses position and acceleration. It
controls the touch buttons and the brightness
of the light. The accelerometer turns off at a
specific angle to avoid causing a distraction
when seen from the worktop. It is calibrated
when the door is closed.
If this symbol appears on the display
the door is not open enough. Open
the door until the display lights up.
Inlet valve
The inlet valve has an electrical connector
that is coded to ensure it is not mixed up. It is
fitted with a filter, which can be removed for
cleaning. Both single and safety valves are used
as inlet valves. The inlet valve contains a filter
to stop particles then a flow limiter to limit
the flow to a maximum of 4 L (1 gallon)/min.
It opens when the water pressure exceeds 0.3
bar (4.3 psi) and provides full flow at about 2
bar (29 psi). It has a pressure range of 0.3 bar
(4.3 psi) to 10 bar (145 psi). The inlet valve is
fitted to the air gap and can be replaced from
the rear of the machine.
Purpose: To ensure that the machine
is supplied with water for the different
dishwashing cycles.
Safety valve
The safety valve has two independent valve seats,
each controlled by a separate electromagnet.
The valve seats are connected in series. This
doubles the safety factor. The electromagnets
are also connected in series (electrically), which
means each magnet’s rated voltage is half the
line voltage (e.g., a 230 V valve = 2 x 115 V coils)
Single valve
The single valve comprises an electromagnet
and a valve seat.
10
Service manual DW Outdoor
Component description
Flow meter
Flow meter
The flow meter is fitted in the air gap and
cannot be replaced separately. It comprises an
impeller that is rotated by the flow of water
from the inlet valve. The impeller is fitted with
two magnets that affect a sensor, a so-called
reed switch. This is connected to the control
unit via a wire and provides the control unit
with information on the amount of water
entering the machine. In order for the flow
sensor to function normally the incoming
water pressure must be at least 2 bar (29 psi).
Output signal: 220 pulses per liter (0.26 gallon)
of water flowing through.
Circulation pump
The circulation pump comprises an asynchronous
motor with a capacitor and a pump housing with
an impeller. The impeller and seals cannot be
replaced separately, rather the entire pump must
be replaced. The circulation pump can be rated
220-240V, 50/60Hz, as well as 120V, 60Hz.
Purpose: To provide the spray system with the
water pressure necessary for the dishwashing
process.
Heating element
The heating element is of the flow-through
type and is fitted between the bottom drain
and the suction connector of the circulation
pump. It comprises a pipe with a heating coil.
One side of the heating coil is fitted with an
overheating cut-out with a trigger temperature
of 98°C (208°F) and an automatic reset. The
other side is fitted with a safety fuse that blows
at 229°C (444°F). The element is replaced
from the rear of the machine by first moving
the circulation pump out of the way.
Purpose: To heat the dishwater to the correct
temperature during the prewash/main wash and
final rinse.
Drain pump
The drain pump is fitted to the bottom drain and
can be replaced from the front of the machine.
In the bottom drain, under the filters, is a access
plug which when removed enables the customer
to clean the pump housing. In the event of a
blockage the pump changes its direction of
rotation to try to clear the blockage.
Purpose: To drain the water from the cleaning
compartment in accordance with the program
specification and in case of overflow.
11
Service manual DW Outdoor
Component description
Detergent and rinse aid dispenser
The dispenser has one container for detergent
and one container for rinse aid. The containers
are opened by activating the electromagnet
found on the lock of each container. When
first activated detergent is dispensed and when
activated a second time rinse aid is dispensed.
A weight (which is activated when the door
is opened for loading and unloading) resets
the mechanism so that the dispenser always
dispenses detergent first when a new program
is started.
Door switch
A micro switch detects when the door has been
opened. The programs is paused and power to
certain components (circulation pump, valves and
more) is cut. The programs continues where it
left off when the door is closed. If a program is
running the machine indicates that the door is
open.
Purpose: To prevent the machine from running
while the door is open.
Light
The light is a 5 W/12 V halogen bulb powered
by the control unit via a micro switch. The lamp
is activated when the door is opened more than
5° and automatically deactivated when the door
has been open for more than 30 minutes. The
control unit features protective components
that limit the current to the light in case of a
short circuit or if a bulb with too high a power
rating is fitted. The bulb can be replaced from
inside the cleaning compartment.
12
Air gap
The air gap is found next to the cleaning
compartment. It comprises channels through
which the incoming water flows into the
cleaning compartment. These channels also
contain an anti-backflow device and the flow
sensor through which the water passes. Certain
models are equipped with a water pocket that
collects water used for the water softener (only
machines with a water softener). The air gap
also works as a channel of air taken in during
the drying phase, as well as a pressure relief for
excess air when opening and closing the door.
On machines with Turbo Drying Express (TDE)
a lid is mounted on the inside of the air gap. If
there is condensation in the kitchen interiors,
make sure the lid is correctly fitted.
Purpose: To prevent dirty water from the
cleaning compartment being sucked back into
the water supply, and lead air to and from the
container.
Service manual DW Outdoor
Component description
Thermistor
The thermistor for temperature measurement
is located at the front edge of the bottom
drain. The thermistor measures and controls
the water temperature, which can be up to
70°C (158°F). If the thermistor short-circuits or
loses contact with the CU, or of the thermistor
does not register a temperature increase of
5°C (41°F) within 10 minutes of the element
being activated, the element is switched off and
a fault code is indicated. This is only indicated
in the service menu. The thermistor is of the
NTC type (Negative Temperature Coefficient),
i.e. its resistance decreases as temperature
increases.
Purpose: To control the water temperature during
the dishwashing process.
EMC filter with inductor
The filter is fitted at the front of the base pan
and consists of a number of coils, condensers
and resistors.
Purpose: To eliminate electromagnetic
interference to and from the machine.
Pressure sensor
The pressure sensor is connected to the
pressure chamber in the bottom drain. It
measures the pressure, which corresponds to
the water level in the machine. If the water level
in the machine is too high (for five consecutive
seconds) the drain pump starts and all other
components are switched off. When the correct
level is reached, the program continues where
it left off. If the level sensor generates an output
signal of <1 VDC during the prewash (indicating
a blocked filter), an additional prewash is
activated with an SCS step.
The level sensor also controls the draining
time (can be extended from 20 seconds to a
maximum of 2 min). The sensor also checks the
need to refill (such as if a bowl fills with water).
Purpose: To prevent overflow, to detect a
‘blocked filter’, when necessary refill the machine
(such as if a bowl has filled with water), and to
control the draining time.
Overflow guard
The overflow guard is integrated with the
bottom drain. This overflow guard consists of a
micro switch activated by a float if water collects
on the machine’s base pan. The micro switch is
normally closed. When it is activated, it breaks
the circuit to the CU, the drain pump starts,
the program is interrupted and the machine
indicates an overflow.
Purpose: To provide protection from any
water leaks or flooding from the machine.
Cables
The machine is fitted with coded connectors
to prevent incorrect wiring. The cables comply
with the Rast 2.5 and Rast 5 standards.
13
Service manual DW Outdoor
Programs and control unit
TH
1/C
TS
2
PS
1 23
IS
FM
SS
DIV M
5
IV
CD
FN 1
VAX
CP
KD
2
FL
VAX
3
CP IV
SV
SV
4
MV
MV
DIV
SL
HL
6
BE
I2C
DW90.1, DW90.1OEM, DW90.2, DW90.C, DW90.3
HS
7
UART
8 9
GS TS FM SG NTC
HS
SL
Wiring diagram
DS
RAS
CP
HE
MS
DR
N
TDE
F
L
HE
HE (PTC)
FN2
HWC
1/C
DP
1
FS
EL
TB
VMG
10
14
PTC
AP
3/4
FAN
2
LB
3/4
1/C
CIRCUIT DIAGRAM DW90.1, DW90.1OEM, DW90.2, DW90.C, DW90.3
80 840 68-01
14
This document must not be copied without
our written pemission, and the contents
thereof must not be imparted to a third party
nor be used for any unauthorized purpose.
Contravention will be prosecuted.
Asko Appliances AB
FORMAT A4
Service manual DW Outdoor
KD/CD: COMBI DISPENSER
CP: CIRCULATION PUMP
DIV: WATER DIVERTER VALVE
AP/DP: DRAIN PUMP
DR: DOOR
LB/DS: DOOR SWITCH
F: FILTER
FM: FLOW METER
FL/FN 1: FAN DOOR
FAN/FN 2: FAN BOTTOM
FS: FLOAT SWITCH
EL/HE: HEATING ELEMENT
HE (PTC): HEATING ELEMENT PTC
BE/HL: HALOGEN LAMP
HS: HUMIDITY SENSOR
IS: ILLUM. SWITCH
IV: INLET VALVE
I2C: I2C
TB/MS: MAIN SWITCH
MV: MIX VALVE
TS/PS: PRESSURE SENSOR
VMG/RAS: RINSE AID SENSOR
SL: STATUS LIGHT
SG/SS: SALT SENSOR
SV: SALT VALVE
NTC/TH: THERMISTOR
GS/TS: TURBIDITY SENSOR
UART: UART
VAX: VAX ACTUATOR
HWC: HOT WATER CIRCUIT
WIRES IN ALL MACHINES
INTERNAL CONNECTION
WIRES IN SOME MACHINES
RESISTANCES AT ROOM TEMPERATURE (CA. 20°C/68°F)
VALUES WITH +/-10% ARE REGARDED AS NORMAL
COMPONENT
RADIO INTERFERENCE SUPPRESSION FILTER
HEATING ELEMENT 1200W 120V
HEATING ELEMENT 1600W 230V
HEATING ELEMENT 2040W 230V
THERMISTOR
COMBINED DISPENSER 120V
COMBINED DISPENSER 230V
CIRCULATION PUMP 120V 60HZ
CIRCULATION PUMP 230V 50HZ
CIRCULATION PUMP 220V 60HZ
DRAIN PUMP 120V 60HZ
DRAIN PUMP 230V 50HZ
DRAIN PUMP 230V 60HZ
SPRAY ARM DIVIDER 120V 60HZ
SPRAY ARM DIVIDER 230V 50/60HZ
INLET VALVE SINGLE INCL. 120V
INLET VALVE SAFETY INCL. 120V
INLET VALVE SINGLE INCL. 230V
INLET VALVE SAFETY INCL. 230V
SALT VALVE 120V
MIX VALVE 120V
SALT VALVE 230V
MIX VALVE 230V
HALOGEN LAMP 5W 12V
WAX MOTOR
FAN MOTOR 120V
FAN MOTOR 230V
FAN MOTOR 2 120V
FAN MOTOR 2 230V
RESISTANCE
1 MOHM
12 OHM
32 OHM
25 OHM
60 KOHM
0,28 KOHM
1,32 KOHM
32 OHM
110 OHM
56 OHM
25 OHM
150 OHM
85 OHM
2.6 KOHM
8,5 KOHM
0.95 KOHM
0.5 KOHM
3,9 KOHM
2 KOHM
0,65 KOHM
0,65 KOHM
3 KOHM
2,3 KOHM
<10 KOHM
1.1 KOHM
0.18 KOHM
0,85 KOHM
0,22 KOHM
0,90 KOHM
15
Service manual DW Outdoor
Troubleshooting
Dishwashing results
Check the following points if the dishes are not
clean (always begin by checking any fault codes
and the most recent fault indication in the
service menu):
• That the customer is using the right
dishwashing program.
• If heavily soiled dishes are being loaded,
such as pots or oven dishes, choose a
heavier program.
• Check that the customer is using a suitable
dishwashing detergent, preferably one with
proven good results.
• Detergent is a perishable product. Check
that the detergent is not too old and
that the customer is using the right
amount. Most importantly not too much
detergent.
• For machines with a water softener, dose
as for soft water.
• Check that the customer is loading the
machine correctly.
• Check that no dishes are preventing the
spray arms from rotating and that the
holes are not clogged.
• Check that the machine has the right
water level. See the Water level section for
more information.
• Check that the access plug on the left side
of the bottom drain by the drain pump is
in place.
• Check that the machine heats to the right
temperature.
Common faults
If the dishwasher does not work, you should
first check whether this is due to a simple fault,
something that the customer can rectify. Use
the following questions to troubleshoot the
machine.
Film or marks on dishes after washing
• Is the water softener cover properly
tightened?
• Is the rinse aid dispenser correctly
adjusted?
• Is the water softener correctly adjusted?
• Is there any salt in the salt compartment?
• Is the right type of salt being used?
For more information, see the machine’s
operating instructions.
16
The machine will not start
• Has the house breaker/fuse been tripped
or blown?
• Has the machine been turned on?
• Is the door properly closed?
• Is the water supply turned on?
If the answer to any of the above questions is
“YES” and the machine seems to lack power,
first check that there is power at the main
power switch and the control unit. Replace any
faulty component.
Water remaining in the machine
• Is the drain hose blocked? Check the
connection to the household drain.
• Is the drain hose kinked?
• Are the filters blocked?
• Is the drain pump blocked?
• Is the access plug on the left side of
the bottom drain by the drain pump
incorrectly fitted?
If the fault cannot be found with the help
of this chapter, open the service menu and
perform a function test on all components
Service manual DW Outdoor
Troubleshooting
Water level DW90
When servicing a DW90 dishwasher it is
important to check the water level in the machine.
This is particularly important when programming
the time-controlled water intake. Too low or
too high water level can cause poor dishwashing
results.
Always allow the machine to take in and drain
the water a few times before checking the
level.
Overflow level = 4.7 L (1.24 gallons)
Without spray arm diverter = 3.2 L (0.8 gallons)
(1.5 mm (1/16”) above the level)
With spray arm diverter = 2.95 L (0.7 gallons)
(in line with the level)
Check the level against the lower spray arm hub
In the event of too low water level, the filter
in the inlet valve must always be checked and
rinsed clean of any sediment.
The inlet hose with a 3/4” connection at
both ends has a filter in the connector outside
the machine that must also be checked and
rinsed clean of any sediment.
In the US the inlet hose has a 3/8”
connection at both ends and no filter in the
connector outside the machine.
17
Service manual DW Outdoor
Troubleshooting
Fault indication
DW Outdoor
T8
T1
DISPLAY
D1, I5,
D2, D3
T3
T4
T5
T6
L = LED, S / T = Push button, F = Fault code or plain text on display, D = Display, I = Indication
Tools
The following tools are needed to service the
DW90 dishwasher:
Torx
T20
T25
T30
Ring spanner/wrench
7 mm
16 mm
Fixed open-end wrench, adjustable wrench,
polygrip pliers/slip joint pliers
For cable fasteners, electrical and inlet valve
22 mm
Special tools
8801339
Universal tool, dishwasher
7281370
Hose clamp pliers, Oetiker
8801424
Universal tool, adapter
water softener
18
T7
T2
Service manual DW Outdoor
Troubleshooting
Fault and information codes
Audible signal sounds when a fault is indicated on the display.
Display
Cause
Action
The door is open
Close the door
F:41
Temp stop fault
Temperature increase less than
5°C (41°F) in ten minutes. Program
continues with the process. Only
indicated in service menu.
Check
Element, thermistor, water level, circulation
pump, control unit and cables.
F:10
Overfilling
Too much water in the machine
(pressure sensor) or float activated. If
the water has not been emptied within
60 seconds, the program stops (drain
pump activated).
Check
Drain pump (blocked hose), flow meter,
inlet valve, leaks and cables.
F:42
Check
Thermistor fault
Communication between the
Thermistor, plugs, wire harness, and control
thermistor and control unit has
unit.
stopped or the thermistor is reporting
temperatures greater than 80°C
(176°F). Program continues with the
process. Only indicated in service menu.
F:12
Water inlet fault
< 80 pulses within 60 seconds or
correct number of pulses not achieved
within 255 seconds. Program stops.
Check
Water inlet, flow meter, inlet valve and
cables.
F:40
Inlet valve leakage
Water intake detected when inlet
valve deactivated in program sequence
or standby. In this case the machine
attempts to close the valve by opening
it for 2 seconds and then closing it
again. If water flow through the valve
is still detected any current program is
stopped (drain pump activated).
Check
Leak through inlet valve and flow meter.
F:43
Pressure sensor fault
Output signal > 4.8 V. The program
continues. Only indicated in service
menu.
Check
Pressure sensor, control unit and cables.
F:11
Water outlet fault
Water not drained after 120 seconds
draining. Program stops.
Check
Drain pump, hoses, drain hose fittings,
control unit and cables. Also check whether
filter is blocked.
F:44
Turbidity sensor fault
Only indicated in service menu. The
machine assumes high turbidity in case
of “uncertainty” in the auto program.
Check
Water quality, filters, turbidity sensor and
drain system.
F:45
Spray arm diverter fault
Position switch always closed or open.
The program continues. Only indicated
in service menu.
Check
Spray arm diverter (functioning gearbox,
switches and cables).
19
Service manual DW Outdoor
Service menu
T8
T1
D1, I5,
D2, D3
LCD1
T3
T4
T5
T6
T7
T2
Variant 1
Variant 2
Variant 3
Variant 4
Opening the service menu
Open the door, put the machine in standby mode by pressing the main power switch (T8).
Activate the machine again by pressing the button (T8), press and hold the program selector
PROG + START
(T1) and (T2) for 5 sec. LCD shows:
. When the service menu is opened the most recent
error message is shown, F:XX. All error messages are erased by a total reset. It is only possible
to leave the service menu by pressing the button (T2). It is not possible to leave the service
menu by using the main power switch (T8).
START
Press the button (T2) to navigate the menu system step by step.
PROG
Press the button (T1) to scroll between settings. Press (T2) to save the setting and continue to
the next menu step.
START
Press (T2) at the last step of the menu to close the service menu and save the most recent
settings.
Menu step/Turn/Push
LCD
Comments/instructions
d:01
Mixer valve and inlet valve on (1 second delay between mixer
valve, if available, and inlet valve)
START
Diagnostics
d:02
Inlet valve and mixer valve, if available, off for 1 second then inlet
valve on
d:03
Salt valve on (if available)
d:04
Combi dispenser on
d:05
Circulation pump on and the spray arm diverter (if available) shall
alternate between positions 1 and 3 every 30 seconds
d:06
Circulation pump and heater on - max. 75°C (167°F)
d:07
Fan and Wax motor and Turbo Drying Express and Heating
Water Circuit on
d:08
Drain pump on
d:00
No components on
P:0
Normal water intake volume, default setting
P:5
Water intake volume increases by +5%
P:10
Water intake volume increases by +10%
P:15
Water intake volume increases by +15%
L:0
Time, flow meter switched off, intake time:
pulse value x 0.068 [s]
L:5
Time-controlled water intake increases by +5%
L:10
Time-controlled water intake increases by +10%
L:15
Time-controlled water intake increases by +15%
PROG
START
Water intake
PROG
START
20
Service manual DW Outdoor
Service menu
T8
T1
D1, I5,
D2, D3
LCD1
T3
T4
T5
T6
T7
T2
Variant 1
Variant 2
Variant 3
Variant 4
Menu step/Turn/Push
LCD
Comments/instructions
Variant
U:1
Variant 1, default setting (Temperature, Drying)
U:2
Variant 2 (Temperature, Drying, Delayed start)
U:3
Variant 3 (Temperature, Drying, Delayed start, Time program)
U:4
Variant 4 (Temperature, Drying, Delayed start, Time saver)
EU
Region Europe, default setting
PROG
START
Region
PROG
US
Region USA
AU
Region Australia
Y:0
No fan sequence during program. Dries the load.
Y:1
Fan works in sequence during the wash cycle, not in normal program,
default setting
Y:2
Fan works in sequence during the wash cycle, even during normal
program
A:0
Turbo Drying Express and Heating Water Circuit off, default
setting
A:1
Turbo Drying Express on (Quick). Uses both hot water system
and electrical energy to minimize program time.
A:2
Heating Water Circuit on (ECO). Uses hot water system as
far as possible, aided by electrical energy, to minimize energy
consumption.
S:0
Super rinse off, default setting
S:1
Super rinse on. Adds two extra rinses.
r:0
No total reset next time T2 is pressed, default setting
r:1
Total reset next time T2 is pressed. Should be done after replacing
the control unit to reset all the sensors.
START
Fan sequence
PROG
START
TDE & HWC
PROG
START
Super rinse
PROG
START
Total reset
PROG
START
21
Service manual DW Outdoor
Service and installation
Disassembling and reassembling the machine’s casing
In order to access the machine’s components, first we need to disassemble its casing, either in part
or in full. Once servicing is completed, reassemble the casing with care so that it is properly resealed.
We recommend wearing gloves and using caution when removing the stainless steel panels that
make up the casing of the machine. The panels, once removed, may have unfinished edges that
could be sharp.
Be careful not to damage the casing and seals during disassembly and reassembly! It’s a good
idea to have new seals for the rear motor compartment on hand in case any of them get damaged
and need replacing.
• 88 015 03 – Sealing kit DW Outdoor
Top cover
*
Remove the hose holder/high
loop and undo the top cover
screws at the rear of the
machine.
Then lift and slide the top
cover forward 1 cm (1/2”)
or so to free the catches on
the side panels of the casing.
Lift the top cover from the
machine.
Also undo the screws running
through the top edge of the
cleaning compartment from
inside the machine.
Upper and lower rear panels
Undo the screws in the rear
panel and lift the bottom
edge of the panel to free the
22
catches from the slots in the
side panels. Remove the rear
panel from the machine.
Undo the screws in the lower
back panel.
Service manual DW Outdoor
Service and installation
Rear motor compartment
Undo the screws in the side
panel that attach to the cross
support.
Next undo the screws in
the back cover of the motor
compartment. Angle out the
side panels of the casing and
open the back cover.
NOTE: The seals in the
bushings for the inlet and
outlet hoses, as well as for
the power cable, may need
replacing. Make sure you
have new sealing kit on hand
before starting any work.
Side panels
The two side panels of the casing only need to be removed when you need to access the
machine’s forward motor compartment and when you need to create more space for servicing
the machine (see the ”Increased working space during service” section). The air gap is located
inside the right side panel..
Undo the screw in the side
panel mount in the rear
upper corner.
Undo the screw in the cross
support at the rear of the
machine.
Next undo the screws in
the back cover of the motor
compartment.
Finally, open the door and
undo the screws holding the
side panel in place from the
inside.
Angle out the top edge of
the side panel and then lift
the side panel to free it from
the catches.
The slots in the bottom of
the side panel keep it in
place.
23
Service manual DW Outdoor
Service and installation
Forward motor compartment
In order to access the machine’s forward motor compartment, you must first disassemble the
entire casing and remove the toe kick and the tip guard.
The toe kick and the tip guard are at the
front of the machine. They must be removed
to access the forward motor compartment.
Undo the tip guard screws
on either side of the machine.
The front cover of the motor
compartment can then be
opened.
Reassembly
To reassemble after servicing, follow these instructions in reverse order.
Reassemble the casing with care so that it is properly resealed. If any casing seal or component is
damaged, it must be replaced or repaired before reassembly.
24
Service manual DW Outdoor
Service and installation
Increased working space during service
In order to facilitate servicing the machine you can open up the motor compartment by freeing the
cleaning compartment along the rear edge and tipping it forward to create more space to work with.
Remove the three screws on each side of the cleaning compartment.
Take one of the M6 screws (with O ring) and insert it in the rear hole on the inside of the base.
Repeat for both sides of the machine.
Remove the screw for the air gap.
Loosen the circulation pump from the rubber
mount.
25
Service manual DW Outdoor
Service and installation
Ensure that both door springs are attached so
that the door does not open and tip the machine.
If the machine has door springs that can be
adjusted from the front and is fitted with a
water softener, the right door spring may need
to be fully tensioned. Otherwise the spring
mount may catch on the water softener when
the cleaning compartment is lifted.
Put your foot on the base and lift the cleaning compartment up. Hang the cleaning compartment
on the two screws previously placed in the rear holes on either side of the machine.
Overflow guard wiring
For service visits where the micro switch for the overflow guard is disconnected it is important
that the cables are correctly reattached. If reattached incorrectly the machine will not start.
Connect the 2-pin connector (2) to the two upper pins on the micro switch and the single pin
connector (1) to the lowest pin.
2
1
26
Service manual DW Outdoor
PERSONAL NOTES
27
We reserve the right to make changes.
Download PDF