Advantech | PCM-4153 | User manual | Advantech PCM-4153 User manual

User Manual
ARK-4153
Copyright
The documentation and the software included with this product are copyrighted 2008
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
ARk-4153 User Manual
Part No. 2006K41500
Edition 1
Printed in Taiwan
April 2008
ii
Technical Support and Assistance
1.
2.
Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
Packing List
Before installation, please ensure the following items have been shipped:
! 1 ARK-4153 unit
! 1 Utility CD
! 1 User’s Notes of Phoebus Operation 1st Ed
! 1 Registration and 1 year Warranty card Rev. A
! Wire 9P 20cm D-SUB TO AT POWER ARK-4170/80 use 1700003933
! CABLE 6P-6P-6P 20cm PS/2 KB & MOUSE 20cm 1700060202
Ordering Information
Model Number Description
!
!
!
ARK-4153Y-AL0A1E: Ruggedized system, w/LX800, 256MB memory, 128MB
onboard Flash, WinCE 6.0, phoebus
ARK-4153Y-BL0A1E: Ruggedized system, w/LX800, 256MB memory, 1GB
onboard Flash, WinCE6.0, phoebus
ARK-4153Y-1L0A1E: Ruggedized system, w/LX800, 256MB memory, 1GB
onboard Flash
Optional Accessories
!
!
!
!
!
1757001117 AC 65 W adaptor 100~240 V WO/PFC ARK-4153/70/80
1702002600 POWER Cable UL/CSA(USA) 180D 125 V/10 A 1.83 M
1702002605 POWER CABLE 90D 220VEUROPEAN 250 V/6 A(FRANCE1.8 M
1702031801 Power CABLE 3P (UK) 5 A-Fuse 1.8 M
1700000596 Power Cord (China) CCC, 10 A 250 V, 3P 1830 mm
iii
ARK-4153 User Manual
ARk-4153 User Manual
iv
Contents
Chapter
1
General Introduction ...........................1
1.1
1.2
Introduction ............................................................................................... 2
Product Features....................................................................................... 3
1.2.1 General ......................................................................................... 3
1.2.2 Display .......................................................................................... 3
Chipset ...................................................................................................... 4
1.3.1 Functional Specifications .............................................................. 4
1.3.2 Mechanical Specifications............................................................. 7
1.3.3 Electrical Specifications ................................................................ 7
Table 1.1: Supply Current (Maximum)......................................... 7
1.3.4 Environmental Specification.......................................................... 8
1.3
Chapter
2
H/W Installation....................................9
2.1
Jumpers .................................................................................................. 10
2.1.1 Jumper List ................................................................................. 10
Table 2.1: PCM-4153 Jumper ................................................... 10
2.1.2 Jumper Settings .......................................................................... 10
Table 2.2: J3, Clear CMOS ....................................................... 10
Table 2.3: J5, PCI Vi/O Power................................................... 10
Table 2.4: SW1, Onboard Flash Enable/Disable Selector......... 11
2.1.3 Jumper Description ..................................................................... 12
Connectors.............................................................................................. 13
2.2.1 Ethernet Connector..................................................................... 13
Table 2.5: Ethernet Connector .................................................. 13
2.2.2 Power Input Connector ............................................................... 13
Table 2.6: Power Input Connector............................................. 13
2.2.3 USB Connector ........................................................................... 14
Table 2.7: USB Connector......................................................... 14
2.2.4 COM1, 2, 3, 4 Connector ............................................................ 14
Table 2.8: CO1,2, 3, 4 Connector.............................................. 14
2.2.5 VGA Connector........................................................................... 14
Table 2.9: VGA Connector ........................................................ 15
2.2.6 PS2 Keyboard/Mouse Connector ............................................... 15
Table 2.10: PS2 Keyboard/Mouse Connector ............................. 15
Mechanical .............................................................................................. 16
2.3.1 Jumper and Connector Locations ............................................... 16
Figure 2.1 Jumper and Connector layout .................................. 16
2.3.2 Board Dimensions....................................................................... 17
Figure 2.2 Board Dimension layout, Component Side............... 17
Figure 2.3 Board Dimension layout, Solder Side....................... 17
2.2
2.3
Chapter
3
BIOS Operation ..................................19
3.1
3.2
BIOS Introduction.................................................................................... 20
BIOS Setup ............................................................................................. 20
3.2.1 Main Menu .................................................................................. 21
3.2.2 Standard CMOS Features .......................................................... 22
3.2.3 Advanced BIOS Features ........................................................... 24
3.2.4 Advanced Chipset Features........................................................ 26
3.2.5 Integrated Peripherals................................................................. 27
3.2.6 Power Management Setup ......................................................... 29
3.2.7 PnP/PCI Configurations .............................................................. 30
v
ARK-4153 User Manual
3.2.8
3.2.9
3.2.10
3.2.11
3.2.12
Chapter
Chapter
PC Health Status ........................................................................ 31
Load Optimized Defaults ............................................................ 32
Set Password.............................................................................. 32
Save & Exit Setup....................................................................... 34
Quit Without Saving .................................................................... 34
4
Extension I/O Installation ................. 35
4.1
PC-104.................................................................................................... 36
Figure 4.1 PC-104 ..................................................................... 36
5
Full Disassembly Procedure............ 37
5.1
Introduction ............................................................................................. 38
ARK-4153 User Manual
vi
Chapter
1
1
General Introduction
This chapter gives background
information on the ARK-4153.
Sections include:
! Introduction
! Specifications
1.1 Introduction
Advantech provides embedded platform products and services to system integrators
that go into the most remote or hostile or extreme environments on earth, embedded
platforms that have to work reliably. To meet the demand for a highly modular compact rugged solution, Advantech developed a PC/104+ stackable system that is
designed and qualified for the most demanding of applications. Each system is
housed in a specially cast and milled solid aluminum block with thermal fins which
also help dissipate heat. Another unique feature is the specially designed fanless
thermal solution for embedded PC applications that allows wide temperature operation between -40° ~ +75° C, without active cooling. All electronics are protected in a
compact sealed housing for convenient embedded and stand alone applications,
where space and environment considerations are critical.
Modularity is a key feature and in addition to the PC/104+ ability to stack I/O and
other modules to add functionality, Advantech uses special brackets on the aluminum
enclosure itself so that additional enclosures can also be stacked, making this the
most flexible rugged solution on the market. The core stacking modules use Advantech standard CPU boards: PCM-4153 w/PC/104+ expansion slot with support for
four RS-232, six USB 2.0, audio line-in, line-out, dual LAN and onboard memory/
flash, and special bushings that ensure the system has excellent anti-vibration characteristics.
What is more, the unique removable heatsink and daughter board mean that you can
completely replace the system, retaining just the chassis. Flexibility is the name of
the game in embedded computing, and this new, compact, rugged solution from
Advantech delivers on all fronts and in all environments!
ARK-4153 User Manual
2
1.2.1 General
CPU: Embedded AMD LX800 Processor, up to 500MHz
System Chipset: AMD Geode™ LX800
!
!
BIOS: AWARD® 4 Mbit Flash BIOS
System Memory: Onboard 256 MB Memory, support Double Data Rate (DDR)
SDRAM, DDR333 SDRAM
Power Management: APM 1.2 (Advanced Power Management)
Flash: Onboard 128MB/1GB Flash (IDE interface, default setting is slave)
Watchdog Timer: Single chip Watchdog 255-level interval timer, setup by software
Expansion Interface: Supports ISA and PCI bus for standard PC/104+ device
(internal)
Battery: 2-pin wafer box for external Battery on board I/O (internal)
I/O Interface
– Rear panel: COM1 ~ 4 for RS-232, 1 x KB/MS, 1 x VGA
– Front Panel: 1 x Power LED, 2 x LAN, 4 x USB 2.0, 1 x DC_input, 1 x on/off
switch, 1 x line-in, 1 x line-out
IrDA: N/A
Chipset: Intel 82551ER
Speed: 10/100 Mbps
Standard: IEEE 802.3u 100Base-T
!
!
!
!
!
!
!
!
!
!
1.2.2 Display
!
!
!
!
!
Chipset: AMD Geode LX800
Memory Size: Optimized Shared Memory Architecture, supports up to 64 MB
frame buffer using system memory
Resolution: CRT resolution: up to 1600 x 1200 x 16 bpp at 100 Hz and up to
1024 x 768 x 32 bpp at 60 Hz for TFT LCD
TTL: Hirose connectors support up to 24-bit TFT LCD (internal pin header)
Dual Independent: CRT + TTL (optional)
Note!
If you require the removal of the internal pin header/connector, or
require the modification of the enclosure connector; please ask your
regional support team for the modification process.
3
ARK-4153 User Manual
General Introduction
!
!
Chapter 1
1.2 Product Features
1.3 Chipset
1.3.1 Functional Specifications
1.3.1.1 Processor
Processor
CPU supports.
!
!
!
Supports 200 MHz, 400 MT/S for DDR
(Double Data Rate)
Supports AMD low power LX800 500MHz Processor
Supports 128KB 2nd cache memory on the processor
1.3.1.2 Chipset
Memory
NB: AMD Geode LX800 chip supports.
!
!
Graphic and Video
Controllers
Onboard Memory, supportsa 333M-Hz Double Data Rate
(DDR) SDRAM,
Supports 256 MB SDRAM.
NB: AMD Geode LX800 chip supports.
!
!
!
!
!
!
!
!
Internal Graphics Features
Dual display choose on board: CRT+LCD
(Internal pinheader)
– CRT
Integrated 350 MHz, 24-bit RAMDAC that can directly drive
a progressive scan analog monitor
Supports pixel resolution up to 1920x1440x32 bpp at 85 Hz
and up to 1600x1200x16 bpp at 100-Hz
– LCD (Internal)
Supports up to 24-bit TFT LCD (TTL signal)
Supports up to 1600x1200x32 bpp at 60 Hz for TFT
Optimized Shared Memory Architecture, support 64MB frame
buffer using system memory
2D Graphics Engine
Hardware screen rotation
Second pattern channel support
CRT Connector: D-SUB Conn. 15P 180D(F) x 1
LVDS Connector: Hirose DF13 type 40-pin.(Internal)
PC/104-plus Expansion NB: AMD Geode LX800 chip supports.
!
!
!
!
ARK-4153 User Manual
PCI 2.1 compliant
32-bit 3.3 V 33 MHz PCI interface
Supports PC/PCI DMA
PCI Socket: 30*4(F) 2.00 mm PC/104+ Solder
63.35 mm * 7.87 mm * 9.35 mm (Internal)
4
SB: AMD Geode CS553 chip supports.
!
!
!
!
SB: AMD Geode CS553 chip supports.
!
!
!
!
Power Management
SB: AMD Geode CS553 chip supports.
!
BIOS
USB host interface with support for 4 USB 2.0 ports
USB 1.1 supported by one OHCI-based host controller. USB
2.0 supported by one EHCI-based host controller
Legacy keyboard/mouse software support
USB dual connector: USB CONN. 4P 180D (F) x 2
Supports APM 1.2 (Advanced Power Management)
SB: AMD Geode CS553 chip supports.
!
!
!
Firmware Hub (FWH) interface support
Phoenix 4 M bit Flash BIOS, supports Plug & Play, APM 1.2
Socket: 32 pin PLCC socket x 1
5
ARK-4153 User Manual
General Introduction
USB Interface
66 MB/s IDE controller in UDMA mode per the ATA-5 specification
Legacy and Enhanced PIO (Programmable I/O), MDMA
(Multi DMA), and UDMA (Ultra DMA) modes
Multiplexed with Flash interface
IDE Primary Connector: 44 pins 180D (M) 2.0 mm BOX
HEADER (Internal)
Chapter 1
IDE Interface
1.3.1.3 Others (Chipset)
Serial ports
LPC I/O: SMSC SCH3114 supports.
!
!
!
!
Thermal sensor
LPC I/O: SMSC SCH3114 supports.
!
!
Keyboard/Mouse
connectors
!
!
Compliant with AC97 2.3 specifications
Supports to 20-bit DAC and 18-bit ADC resolution
Audio Connector: PHONE JACK 3P 180D connector.
Battery support: CR2032
!
ARK-4153 User Manual
IEEE 802.3 10BASE-T/100BASE-TX compliant physical layer
interface
IEEE 802.3u Auto-Negotiation support
LAN connector: 2 x Phone Jack RJ45 8P8C 90D
Audio Codec: Realtek ALC203
!
!
!
Battery backup
PS/2 Keyboard and Mouse interface.
PS/2 Connector: 1 x MiniDIM connector x 1
LAN Connector: Intel 82551ER supports.
!
Audio
Monitor the current CPU temperature
Monitor the main power voltage
LPC I/O: SMSC SCH3114 supports.
!
!
LAN
4 full function serial ports by SMSC SCH3114.
Support IRQ Sharing among serial ports
High Speed NS16C550A Compatible UARTs.
COM connector: D-Sub 9pin connector x 4
BATTERY 3V/210 mAh with WIRE x 1
6
Chapter 1
1.3.2 Mechanical Specifications
1.3.2.1 Dimension
(L) 164 mm x (W) 170 mm x (D) 49.2 mm
1.3.2.2 Weight (g) with Heatsink
2 kg
1.3.3 Electrical Specifications
+12 VDC (For some PC/104, PC/104+ cards and LVDS inverter power)
1.3.3.2 Power Supply Current
Table 1.1: Supply Current (Maximum)
Operating mode
Voltage
Current(Max.) Power
Note
DOS mode
5V
1.14 A
5.7 0W
With CF card
12 V
<0.01 A
<0.12 W
5V
1.31 A
6.55 W
12 V
<0.01 A
<0.12 W
5V
1.76 A
8.80W
12 V
<0.01 A
<0.12 W
5V
3.35 A
17.75 W
12 V
<0.01 A
<0.12 W
Windows XP with SP2
Windows XP + HCT
Windows XP + USB Full
Load (0.5 A for each of four
USB ports)
With 2.5” HDD
1.3.3.3 RTC Battery
Nominal Voltage: 3.0 V
Nominal discharge capacity: 210 mAh
7
ARK-4153 User Manual
General Introduction
1.3.3.1 Power Supply Voltage
Voltage requirement with AT Power:
+5 VDC +/- 5%
1.3.4 Environmental Specification
1.3.4.1 Operating temperature
Operating temperature: -40 ~ 75° C
1.3.4.2 Operating Humidity
Operating Humidity: 0% ~ 90% Relative Humidity, non-condensing
1.3.4.3 Storage temperature
Standard products (0 ~ 60° C)
Storage temperature: -20 ~ 70° C
Phoenix products (-20 ~ 80° C)
Storage temperature: -20 ~ 80° C
Platinum Phoenix products (-40 ~ 85° C)
Storage temperature: -40 ~ 85° C
1.3.4.4 Storage Humidity
Standard products (0 ~ 60° C)
Relative humidity: 95% @ 60° C
Phoenix products (-20 ~ 80° C)
Relative humidity: 95% @ 60° C
Platinum Phoenix products (-40 ~ 85° C)
Relative humidity: 95% @ 60° C
ARK-4153 User Manual
8
Chapter
2
H/W Installation
2
2.1 Jumpers
2.1.1 Jumper List
Table 2.1: PCM-4153 Jumper
J3
Clear CMOS
J5
PCI VI/O Power Selector
SW1
Onboard/Flash Enable/Disable selector
2.1.2 Jumper Settings
2.1.2.1 Clear CMOS
ARK-4153 series of embedded box computers provides a jumper, J3, located on the
internal main board for selecting the CMOS of Clear or Normal status.
Table 2.2: J3, Clear CMOS
Close pins
Function
1-2
Normal*
2-3
Clear CMOS
(*): means default setting of the jumper/function.
2.1.2.2 PCI VI/O Power
ARK-4153 series of embedded box computers provides a jumper, J5, located on the
internal main board for selecting PCI VI/O power of 5 V or 3.3 V.
Table 2.3: J5, PCI Vi/O Power
Close pins
Function
1-2
+5 V
2-3
+3.3 V*
(*): means default setting of the jumper/function.
ARK-4153 User Manual
10
Table 2.4: SW1, Onboard Flash Enable/Disable Selector
1653002101
Footprint
JH2X1V-2M
Description
PIN HEADER 2*1P
180D (M)SQARE 2.0 mm
Setting
Function
(1-2)
Disable
(2-3)
Enable (Default)
Note!
H/W Installation
Part Number
If you want to use a CF card to replace onboard Flash, we suggest you
order PCM-3835-00A1E, which is the PC/104 CF socket module, and
install the module with CF card into ARK-4153 and disable onboard
Flash.
11
Chapter 2
2.1.2.3 Onboard Flash Enable/Disable Selector
ARK-4153 provides onboard NAND Flash memory to replace CF socket. It supports
128MB/1GB Flash, flash endurance is about 100K program/erase cycles and data
retention is ten years. The default setting is flash function enabled, if you do not want
to use the flash function, set SW1 to disable.
ARK-4153 User Manual
2.1.3 Jumper Description
Cards can be configured by setting jumpers. A jumper is a metal bridge used to close
an electric circuit. It consists of two metal pins and a small metal clip (often protected
by a plastic cover) that slides over the pins to connect them. To close a jumper, you
connect the pins with the clip. To open a jumper, you remove the clip. Sometimes a
jumper will have three pins, labeled 1, 2 and 3. In this case you would connect either
pins 1 and 2, or 2 and 3.
The jumper settings are schematically depicted in this manual as follows.
1
2
3
A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes.
Warning! To avoid damaging the computer, always turn off the power supply
before setting jumpers. Clear CMOS. Before turning on the power supply, set the jumper back to 3.0 V Battery On.
ARK-4153 User Manual
12
2.2.1 Ethernet Connector
The ARK-4153 is equipped with an Intel 82551ER Ethernet LAN controller that is fully
compliant with IEEE 802.3u 10/100Base-T standards. The Ethernet port provides a
standard RJ-45 jack on board.
Chapter 2
2.2 Connectors
Table 2.5: Ethernet Connector
10/100BaseT Signal Name
1
XMT+
2
XMT-
3
RCV+
4
NC
5
NC
6
RCV-
7
NC
8
NC
H/W Installation
Pin
2.2.2 Power Input Connector
ARK-4153 comes with a DB-15 pin connector for AT external power input. Use the
DB-15 AT power cable (P/N: 1700003933) to connect with the AT power supply. If
you need a power adaptor, you can order a separate power adapter (P/
N:1757001117) which is an AC 65W adaptor 100~240 V WO/PFC ARK-4153/70/80.
Table 2.6: Power Input Connector
Pin
Signal Name
1
+5 V
2
+5 V
3
GND
4
GND
5
+12 V
6
+5 V
7
+5 V
8
GND
9
GND
13
ARK-4153 User Manual
2.2.3 USB Connector
The USB connector is used for connecting any device that conforms to the USB interface. The USB interface supports Plug and Play, which enables you to connect or
disconnect a device whenever you want, without turning off the computer.
ARK-4153 provides four USB interface connectors on the front panel. The USB interface is compliant with USB UHCI, Rev. 2.0.
Table 2.7: USB Connector
Pin
Signal Name
1
VCC
2
USB_P-
3
USB_P+
4
GND
2.2.4 COM1, 2, 3, 4 Connector
ARK-4153 offers four standard RS-232 serial communication interface ports, each
with a 9-pin DE-9 connector.
Table 2.8: CO1,2, 3, 4 Connector
1 2 3 4 5
6 7 8 9
Pin
Signal Name
1
DCD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
DTS
8
CTS
9
RI
2.2.5 VGA Connector
ARK-4153 provides a VGA controller for a high resolution VGA interface, it supports:
CRT Modes: 1280 x 1024 @ 32bpp (60Hz), 1024 x 768 @ 32bpp (85Hz); LCD/
Simultaneous Modes: 1280 x 1024 @ 16bpp (60Hz), 1024 x 768 @16bpp(60Hz) and
up to 32 MB shared memory.
ARK-4153 User Manual
14
Chapter 2
Table 2.9: VGA Connector
1
5
15
11
Signal Name
1
Red
2
Green
3
Blue
4
NC
5
GND
6
GND
7
GND
8
GND
9
NC
10
GND
11
NC
12
NC
13
H-SYNC
14
V-SYNC
15
NC
H/W Installation
Pin
2.2.6 PS2 Keyboard/Mouse Connector
ARK-4153 provides a single PS/2 keyboard/mouse connector. A 6-pin mini-DIN connector is located on the rear panel of ARK-4153.
ARK-4153 comes with a Y adapter to convert from the single 6-pin mini-DIN connector to dual 6-pin mini-DIN connectors for PS/2 keyboard and PS/2 mouse connections.
Table 2.10: PS2 Keyboard/Mouse Connector
6
5
4
3
2
1
Pin
Signal Name
1
PS2_KBDAT
2
PS2_MSDAT
3
GND
4
VCC
5
PS2_KBCLK
6
PS2_MSCLK
15
ARK-4153 User Manual
2.3 Mechanical
2.3.1 Jumper and Connector Locations
ON / OFF
PWR LED
LAN1
LAN2 USB4
USB3 USB2
DC_INPUT LINE_OUT LINE_IN
COM2
COM1
RESET
VGA
4153
COM4
COM3
KB / MS
Figure 2.1 Jumper and Connector layout
ARK-4153 User Manual
16
USB1
units: mm
Chapter 2
2.3.2 Board Dimensions
H/W Installation
Figure 2.2 Board Dimension layout, Component Side (dimensions in mm)
units: mm
0.25
Figure 2.3 Board Dimension layout, Solder Side (dimensions in mm)
17
ARK-4153 User Manual
ARK-4153 User Manual
18
Chapter
3
BIOS Operation
Sections include:
! BIOS Introduction
! BIOS Setup
3
3.1 BIOS Introduction
Advantech provides full-featured Award BIOS 6.0 and delivers the superior performance, compatibility and functionality that manufacturers of Industry PC and Embedded boards demand, offering many options and extensions that let you customize
your products to a wide range of designs and target markets.
The modular, adaptable Award BIOS 6.0 supports the broadest range of third-party
peripherals and all popular chipsets, plus Intel, AMD, nVidia, VIA, and compatible
CPUs from 386 through Pentium and AMD Geode, K7 and K8 (including multiple processor platforms), and VIA Eden C3 and C7 CPUs.
You can use Advantech’s utilities to select and install features to suit your designs to
the customers’ needs.
3.2 BIOS Setup
The ARK-4153 Series systems have built-in AwardBIOS with a BIOS SETUP utility
which allows the user to configure required settings or to activate certain system features.
The BIOS SETUP saves the configuration in the CMOS RAM of the motherboard.
When the power is turned off, the battery on the board supplies the necessary power
to the CMOS RAM so that configuration settings are retained.
To access the BIOS CMOS SETUP screen, when system power is turned on, press
the <Del> button during the BIOS POST (Power-On Self Test).
CONTROL KEYS
< ↑ >< ↓ >< ← >< → > Move to select item
<Enter>
Select Item
<Esc>
Main Menu - Quit without saving changes into CMOS
Sub Menu - Exit current page and return to Main Menu
<Page Up/+>
Increase the numeric value or make changes
<Page Down/->
Decrease the numeric value or make changes
<F1>
General help, for Setup Sub Menu
<F2>
Item Help
<F5>
Load Previous Values
<F7>
Load Optimized Default
<F10>
Save all changes to CMOS
ARK-4153 User Manual
20
Early in bootup, press <Del> to enter the AwardBIOS CMOS Setup Utility; the Main
Menu will appear on the screen. Use arrow keys to select among the items and press
<Enter> to accept or enter a sub-menu.
Chapter 3
3.2.1 Main Menu
BIOS Operation
!
!
!
!
!
!
!
!
!
!
!
Standard CMOS Features
This setup page includes all the items in the standard compatible BIOS.
Advanced BIOS Features
This setup page includes all the Award BIOS enhanced features.
Advanced Chipset Features
This setup page includes all the chipset configuration features.
Integrated Peripherals
This setup page includes all onboard peripheral devices.
Power Management Setup
This setup page includes all the Power Management features.
PnP/PCI Configurations
This setup page includes PnP OS and PCI device configuration.
PC Health Status
This setup page includes the system auto detect CPU and system temperature,
voltage, fan speed.
Load Optimized Defaults
This setup page includes Load system optimized value, and the system would
be in best performance configuration.
Set Password
Establish, change, or disable passwords.
Save & Exit Setup
Save CMOS value settings to CMOS and exit BIOS setup.
Exit Without Saving
Abandon all CMOS value changes and exit BIOS setup.
21
ARK-4153 User Manual
3.2.2 Standard CMOS Features
!
Date
The date format is <Weekday>, <Month>, <Day>, <Year>.
– Weekday
– Month
– Day
– Year
!
!
!
!
Time
The time format is in <hours>: <minutes>: <seconds>, based on 24-hour time
IDE Channel 0 Master/Slave
– IDE HDD Auto-Detection. Press "Enter" for automatic device detection.
IDE Channel 1 Master/Slave
– IDE HDD Auto-Detection. Press "Enter" for automatic device detection.
Drive A / Drive B
This item identifies the types of floppy disk drives occupying A and B
– None
!
From Sun to Sat, once set, calculated and displayed by the
BIOS
From Jan to Dec.
From 1 to 31
From 1999 through 2098
– 360 K, 5.25"
No floppy drive installed
5.25 inch PC-type standard drive; 360 KB capacity
– 1.2 M, 5.25"
5.25 inch AT-type high-density drive; 1.2 MB capacity
– 720 K, 3.5"
3.5 inch double-sided drive; 720 KB capacity
– 1.44 M, 3.5"
3.5 inch double-sided drive; 1.44 MB capacity
– 2.88 M, 3.5"
3.5 inch double-sided drive; 2.88 MB capacity
Halt on
This item determines whether the computer bootup process will stop if an error
is detected during power up.
– No Errors
– All Errors
ARK-4153 User Manual
The system boot sequence will not stop for any error.
Whenever the BIOS detects a non-fatal error the system will stop.
22
– All, but Diskette
– All, but Disk/Key
!
!
Base Memory
The BIOS POST displays the amount of base (or conventional) memory
installed in the system.
Extended Memory
The BIOS POST displays the amount of extended memory (above 1 MB in the
CPU's memory address map) installed in the system.
Total Memory
This item displays the total system memory size.
23
ARK-4153 User Manual
BIOS Operation
!
The system boot sequence will not stop for a keyboard error, but it will stop for all other errors. (Default
value)
The system boot sequence will not stop for a diskette
drive error, but it will stop for all other errors.
The system boot sequence will not stop for a keyboard or disk error, but it will stop for all other errors.
Chapter 3
– All, but Keyboard
3.2.3 Advanced BIOS Features
!
!
!
!
Virus Warning [Disabled]
This item allows user to choose the VIRUS Warning feature for IDE Hard Disk
boot sector protection.
CPU Internal Cache
[Enabled]
This item allows user to enable CPU internal cache.
Quick Power On Self Test [Enabled]
This field speeds up the Power-On Self Test (POST) routine by skipping retesting a second, third and forth time. Setup setting default is enabled.
First / Second / Third / Other Boot Drive
–
–
–
–
–
–
–
–
–
–
–
Floppy
LS120
Hard Disk
CDROM
ZIP
USB-FDD
USB-ZIP
USB-CDROM
USB-HDD
LAN
Disabled
Assign this boot device priority to Floppy.
Assign this boot device priority to LS120.
Assign this boot device priority to Hard Disk.
Assign this boot device priority to CDROM.
Assign this boot device priority to ZIP.
Assign this boot device priority to USB-FDD.
Assign this boot device priority to USB-ZIP.
Assign this boot device priority to USB-CDROM.
Assign this boot device priority to USB-HDD.
Assign this boot device priority to LAN.
Do not assign this boot priority.
!
Boot Up Floppy Seek [Enabled]
When enabled, the BIOS will try to detect and initialize a floppy drive, which can
add several seconds to bootup time.
!
Boot Up NumLock Status [On]
This item enables users to activate the Number Lock function upon system
boot.
Gate A20 Option [Fast]
This item enables users to switch A20 control by port 92 or not.
Typematic Rate Setting [Disabled]
This item enables users to set the two typematic controls items.
!
!
ARK-4153 User Manual
24
– System
!
!
!
!
25
ARK-4153 User Manual
BIOS Operation
!
System can not boot and can not access Setup page if the correct
password is not entered at the prompt.
– Setup
System will boot, but access to Setup is denied if the correct password is not entered at the prompt. (Default value)
OS Select for DRAM > 64 M [Non-OS2]
Select OS2 only if the system is running OS/2 with greater than 64 MB of RAM
on the system.
Video BIOS Shadow [Enabled]
Enabled copies Video BIOS to shadow RAM improves performance
– C8000-CBFFF Shadow [Disabled]
It’s for shadow control of item.
– CC000-CFFFF Shadow [Disabled]
It’s for shadow control of item.
– D0000-D3FFF Shadow [Disabled]
It’s for shadow control of item.
– D4000-D7FFF Shadow [Disabled]
It’s for shadow control of item.
– D8000-DBFFF Shadow [Disabled]
It’s for shadow control of item.
– DC000-DFFFF Shadow [Disabled]
Small Logo (EPA) Show [Enabled]
Shows EPA logo during system POST stage.
Summary Screen Show [Enabled]
Shows system status on summary screen page.
Cyrix 6X86/MII CPUID [Enabled]
This item allows user to control BIOS enabled or disabled CPUID for CPU
Cyrix/MII.
Chapter 3
!
– Typematic Rate (Chars/Sec)
This item controls the speed of repeated keystrokes.
Eight settings are 6, 8, 10, 12, 15, 20, 24 and 30.
– Typematic Delay (Msec)
This item sets the time interval before auto repetition of characters begins.
The four delay rate options are 250, 500, 750 and 1000.
Security Option [Setup]
3.2.4 Advanced Chipset Features
Note!
!
!
!
!
!
!
!
!
!
!
!
This “Advanced Chipset Features” option controls the configuration of
the board’s chipset, this page is developed to be chipset independent,
for fine tuning system performance. It is strongly recommended that only
technical users make changes to the default settings.
CPU Frequency [Enabled]
This item enables users to set the CPU Host clock by system automatic detection or manually.
Memory Frequency [400 MHz] (Show Only)
This item enables users to set the Memory Host clock by system automatic
detection or by manual.
Video Memory Size [8 M]
This item allows user to adjust VGA share memory size for personal purpose.
Output Display [CRT]
This item allows user to choose screen display type. BIOS default value is set
to “CRT”.
Flat Panel Configuration [Press Enter] (Show Only)
This item provides flat panel function for user adjustment.
Onboard Audio [Enabled]
This item controls enabling or disabling of the motherboard audio device.
Onboard USB1.1 [Enabled]
This item controls enabling or disabling of the motherboard USB1.1 device.
Onboard USB2.0 [Enabled]
This item controls enabling or disabling of the motherboard USB2.0 device.
Onboard IDE [Enabled]
This item controls enabling or disabling of the motherboard IDE device.
Memory Hole At 15 M-16 M [Disabled]
This item reserves 15MB-16MB memory address space to ISA expansion cards
that specifically require the setting. Memory from 15MB-16MB will be unavailable to the system because of the expansion cards can only access memory at
this area.
Overcurrent Reporting [Disabled]
ARK-4153 User Manual
26
3.2.5 Integrated Peripherals
Chapter 3
!
This item enables or disables USB overcurrent report function. Bios default is
Disabled.
Port 4 assignment [Host]
This item allows user to changed USB port 4 mode.
BIOS Operation
Note!
!
!
!
!
!
!
!
!
This “Integrated Peripherals” screen controls the configuration of the
board’s chipset, including controls for: IDE, ATA, SATA, USB, AC97,
MC97 and Super IO and sensor devices; this page is developed to be
chipset independent.
On-Chip IDE Channel 1
This item enables chipset IDE device 1 of controller.
Master Drive PIO Mode [Auto]
This item allows user to adjust master IDE mode for modification purposes.
Bios default value: “Auto”.
Slave Drive PIO Mode [Auto]
This item allows user to adjust slave IDE mode of type for modification purpose.
Bios default value: “Auto”.
IDE Primary Master UDMA [Auto]
This item allows user to adjust primary master IDE mode of type for modification purpose. Bios default value: “Auto”.
IDE Primary Slave UDMA [Auto]
This item allows user to adjust primary slave IDE mode of type for modification
purpose. Bios default value: “Auto”.
IDE DMA transfer access [Enabled]
This item allows user to adjust IDE DMA mode. It will increase IDE Data transfer of speed. Bios default value: “Enabled”.
LAN1 Controller [Enabled]
This item is enabled or disabled that onboard of LAN1 controller. Bios default
value: "Enabled”.
LAN2 Controller [Enabled]
27
ARK-4153 User Manual
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
This item is enabled or disabled that onboard of LAN2 controller. Bios default
value: “Enabled”.
ITE8888 Configure [Press Enter]
This item allows user to changed ITE8888 of detail adjust.
IDE HDD Block Mode [Enabled]
This item allows enabled or disabled that IDE block data transfer mode. It will
speed up HDD data transfer of efficiency. Bios default value: “Enabled”.
LPT/FDC switch [Disabled]
This item is switch LPT/FDC port by item. It will changed from LPT to FDC port.
Bios default value: “Disabled”.
Onboard Serial Port 1 [3F8]
This item allows user to change com 1 of address. Bios default value: “3F8”.
Onboard Serial Port 1 use [IRQ4]
This item allows user to change com 1 of IRQ. Bios default value: “IRQ4”.
Onboard Serial Port 2 [2F8]
This item allows user to change com 2 of address. Bios default value: “2F8”.
Onboard Serial Port 2 use [IRQ3]
This item allows user to change com 2 of IRQ. Bios default value: “IRQ3”.
Onboard Serial Port 3 [3E8]
This item allows user to change com 3 of address. Bios default value: “3E8”.
Onboard Serial Port 3 use [IRQ10]
This item allows user to change com 3 of IRQ. Bios default value: “IRQ10”.
Onboard Serial Port 4 [2E8]
This item allows user to change com 4 of address. Bios default value: “2E8”.
Onboard Serial Port 4 use [IRQ5]
This item allows user to change com 4 of IRQ. Bios default value: “IRQ5”.
Auto Flow Control [Disabled]
This item allows user to control com port of auto flow transfer. Bios default
value: “Disabled”.
Onboard Parallel Port [378/IRQ7]
This item allows user to change parallel port of address. Bios default value:
”378/IRQ7”.
Onboard Parallel Mode [Standard]
This item allows user to change parallel port of mode. User can choose
“SPP”,”EPP”, ”ECP” and “ECP+EPP”. SPP (Standard Parallel Port).ECP
(Extended Capabilities Port). EPP (Enhanced Parallel Port). Bios default value:
“Normal”.
ECP Mode Use DMA [3]
This item allows user to change DMA channel for parallel port. Bios default
value: “3”.
ARK-4153 User Manual
28
!
!
!
!
!
!
!
This “Power Management Setup” screen configures the system to most
effectively save energy while operating in a manner consistent with your
computer use.
ACPI Function [Enabled] (Show Only)
This item defines the ACPI (Advanced Configuration and Power Interface) feature that makes hardware status information available to the operating system,
and communicates PC and system device information for improving power
management.
Power Management [ACPI]
– Legacy
Opens two items for adjustment: “Standby Mode” and “Suspend Mode”.
– APM
APM (Advanced Power Management function).
– ACPI
ACPI (Advanced Configuration and Power Management).
Standby Mode [Disabled]
This item allows user to select standby time. Range from 1 sec to 120 Min.
Suspend Mode [Disabled]
This item allows user to select suspend of time. Range from 1 sec to 120 Min.
Modem use IRQ
[N/A]
This item allows user to determine the IRQ which the MODEM can use.
Soft-Off by PWR-BTTN [Instant-Off]
This item allows user to define function of power button.
– Instant-Off
Press power button then Power off instantly.
– Delay 4 Sec
Press power button 4 sec. to Power off.
Power-On by Alarm [Disabled]
This item allows user to enable and key in Date/time to power on system
– Disabled
Disable this function.
– Enabled
Enable alarm function to power on system
– Time (HH:MM:SS) Alarm
(0-23) : (0-59) : 0-59)
29
ARK-4153 User Manual
BIOS Operation
Note!
Chapter 3
3.2.6 Power Management Setup
!
IRQ Wakeup Events [Press Enter]
This item allows user to control wakeup from which IRQ event.
3.2.7 PnP/PCI Configurations
Note!
!
!
!
!
!
This “PnP/PCI Configurations” screen is setting up the IRQ and DMA
(both PnP and PCI bus assignments.)
PNP OS Installed [No]
This item allows user to determine PNP function install or not.
Init Display First [Onboard]
This item is setting for start up Video output from Onboard or PCI device.
Reset Configuration Data [Disabled]
This item allow user to clear any PnP configuration data stored in the BIOS.
Resources Controlled By [Auto (ESCD)]
– IRQ Resources
This item allows you respectively assign an interruptive type for IRQ-3, 4, 5, 7,
9, 10, 11, 12, 14, and 15.
– Memory Resources
This item allows you respectively assign a memory block from N/A to DC00.
PCI VGA Palette Snoop [Disabled]
The item is designed to solve problems caused by some non-standard
VGA cards. A built-in VGA system does not need this function.
ARK-4153 User Manual
30
!
!
This “PC Health Status” screen reports the thermal, fan and voltage statuses of the board. This page is developed to be chipset independent.
Current System/CPU Temp [Show Only]
This item displays current system and CPU temperature.
5 V / 12 V and VCore [Show Only]
This item displays current CPU and system Voltage.
31
ARK-4153 User Manual
BIOS Operation
Note!
Chapter 3
3.2.8 PC Health Status
3.2.9 Load Optimized Defaults
Note!
Load Optimized Defaults loads the default system values directly from
ROM. If the stored record created by the Setup program should ever
become corrupted (and therefore unusable), these defaults will load
automatically when you turn the system on.
3.2.10 Set Password
Note!
To enable this feature, you should first go to the Advanced BIOS Features menu, choose the Security Option, and select either Setup or System, depending on what you want password protected. Setup requires
the password only to enter Setup. System requires the password every
time the system boots, and to enter Setup. A password may be at most
8 characters long.
ARK-4153 User Manual
32
To Establish Password
1. Choose Set Password from the CMOS Setup Utility main menu and press
<Enter>.
2. When you see “Enter Password”, enter the desired password and press
<Enter>.
3. At the “Confirm Password” prompt, retype the desired password, then press
<Enter>.
4. Select Save to CMOS and EXIT, type <Y>, then <Enter>.
Chapter 3
To Change Password
1. Choose Set Password from the CMOS Setup Utility main menu and press
<Enter>.
2.
When you see “Enter Password”, enter the existing password and press
<Enter>.
3. You will see “Confirm Password”. Type it again, and press <Enter>.
4. Select Set Password again, and at the ”Enter Password” prompt, enter the new
password and press <Enter>.
5. At the ”Confirm Password” prompt, retype the new password, and press
<Enter>.
6. Select Save to CMOS and EXIT, type <Y>, then <Enter>.
BIOS Operation
To Disable Password
1. Choose Set Password from the CMOS Setup Utility main menu and press
<Enter>.
2. When you see “Enter Password”, enter the existing password and press
<Enter>.
3. You will see “Confirm Password”. Type it again, and press <Enter>.
4. Select Set Password again, and at the “Enter Password” prompt, don’t enter
anything; just press <Enter>.
5. At the “Confirm Password” prompt, again, don’t type in anything; just press
<Enter>.
6. Select Save to CMOS and EXIT, type <Y>, then <Enter>.
33
ARK-4153 User Manual
3.2.11 Save & Exit Setup
Note!
Type “Y” will quit the BIOS Setup Utility and save user setup values to
CMOS.
Type “N” will return to BIOS Setup Utility.
3.2.12 Quit Without Saving
Note!
Type “Y” will quit the BIOS Setup Utility without saving to CMOS.
Type “N” will return to BIOS Setup Utility.
ARK-4153 User Manual
34
Chapter
4
Extension I/O
Installation
4
4.1 PC-104
Be sure that pins align with sockets,
then apply force evenly.
Figure 4.1 PC-104
ARK-4153 support 1 x PC/104+ connector inside, you can stack 1 x PC/104+ module
on the top on the heatsink.
ARK-4153 User Manual
36
Chapter
5
5
Full Disassembly
Procedure
This chapter details the system
disassembling procedure for setting up the jumpers and for maintenance.
5.1 Introduction
If you want to completely disassemble the ARK-4153 embedded box computer, follow the step-by-step procedures below. Users should be aware that Advantech Co.,
Ltd. takes no responsibility whatsoever for any problems or damage caused by the
user disassembly of the ARK-4153 embedded box computer. Make sure the power
cord of the ARK-4153 embedded box computer is unplugged before you start disassembly.
1. Unscrew the 6 screws on the top: four each M3, and two each M2, to the sides.
2.
Unscrew the 4 x M3 screws on the top cover.
ARK-4153 User Manual
38
Chapter 5
Full Disassembly Procedure
3.
Unscrew the 2 x M2 screws on the top cover.
39
ARK-4153 User Manual
4.
The top cover removed.
5.
Unscrew the 6 screws on bottom cover: four M3s, and two M2s, to the sides.
ARK-4153 User Manual
40
The bottom cover removed.
7.
Pull the cable from the CPU board and I/O daughter board carefully.
Chapter 5
6.
ARK-4153 User Manual
Full Disassembly Procedure
41
8.
Unscrew the screws on the sides of the heatsink.
9.
Remove the heatsink and PC-104 CPU board from the enclosure.
ARK-4153 User Manual
42
Chapter 5
10. Unscrew the connector screws on the panel board.
Full Disassembly Procedure
43
ARK-4153 User Manual
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2007
Download PDF