Zigen | ZIG-HDMI-UCE | User manual | Zigen ZIG-HDMI-UCE User manual

 HDMI/VGA Auto-switching wall plate
HDBaseT transmitter over single CAT5e/6/7 100m, IEEE POE Powered, 4K, Audio, IR,
RS232, LAN - WebOS
ZIG-POEWP-100
USER MANUAL Ver. 1.0
zigencorp.com
Toll Free: 877-650-5252
International: +1 818-654-5252
Table of Contents
Copyright and Trademark
Introduction
Package Contents
Features
Specifications
Panel Description – Front Side
Panel Description – Back Side
Connection and Installation
Initial Connections
Remote Control
WebOS Interface
RS-232 Commands
Warranty
2 ZIG-­‐POEWP-­‐100 USER MANUAL 3
4
4
4
5
7
9
11
12
13
14
17
20
Copyright and Trademarks:
All rights reserved by ZIGEN, INC. No part of this document may be reproduced
in any form or by any means without written permission from the product
manufacturer. Changes are periodically made to the information in this
document. They will be incorporated in subsequent editions. The product
manufacturer may make improvements and /or changes in the product described
in this document at any time.
All the registered trademarks referred to this manual are belonging to their
respective companies.
Before You Begin
Follow all instructions marked on the device during use. Do not attempt to
maintain the device by yourself, any faults, please contact your vendor.
§ Provide proper ventilation and air circulation and do not use near water.
§ It is better to keep it in a dry environment.
§The system should be installed indoor only.
§ Only use the power cord supplied with the device.
§ Do not use liquid or aerosol cleaners to clean the device.
§ Always unplug the power to the device before cleaning.
§Unplug the power cord during lightning or after a prolonged period of
non-use to avoid damage to the equipment.
zigencorp.com
Toll Free: 877-650-5252
International: +1 818-654-5252
Introduction
The ZIG-POEWP-100 is a wall plate 100 meter (328 feet) HDBaseT transmitter.
It can be powered with a 5 VDC supply or from a POE RX device that it is
connected to like a ZIG-PS-61 or ZIG-POE-RXAV. It can be used stand-alone as
an HDBaseT wall-plate transmitter, but really shines when paired with the ZIGPOE-RXAV receiver/scaler & audio amplifier. A perfect “no-control” control
system using “on-connection” technology to fire up projectors, drop screens and
control lighting in small rooms – BYOD and in seconds collaborate with your
colleagues with full audio and video in stunning 4K UHD. A must for conference
rooms and huddle spaces.
Package Contents
•
•
1 x ZIG-POEWP-100
1 x User Manual
Features
•
•
•
•
•
•
•
•
•
HDMI and VGA w/Audio input – VGA can be configured as Component,
Y/C or C.
Auto-Switching function – if you remove an active source – and another
source is connected then it will switch to the new source immediately.
IEEE POE – remote or source – can connect to IEEE POE device for
power or can connect directly to a 5VDC source via 2-pin phoenix style
connector on the back.
WebOS setup and control – or control from ZIG-POE-RXAV hand-held
remote – simple automation or integrate into 3rd party controller.
Supports HDMI 1.2, 1.3 and 1.4 with 48-bit deep color
Supports digital video formats up to Ultra HD 4K/2K, 60Hz, 4:2:0 pixel
format
Supports uncompressed PCM 2- Ch., 5.1, 7.1, Dolby Digital, DTS, Dolby
TrueHD, DTS HD-Master Audio and more.
Supports IR, RS-232 commands
Supports HDCP 1.4 & 2.2
4 ZIG-­‐POEWP-­‐100 USER MANUAL Specifications
Ports
Inputs
HDMI x 1
VGA x 1 – multi-port – supports YPbPr, Y/C and C
3.5mm Audio port – follows VGA port
Power – On back – 5VDC direct or IEEE POE from RX or switch
Outputs
HDBasetT x 1 – RJ45
Control/Access
Via RJ45 and WebOS for direct control. Can also be accesses and controlled via
ZIG-POE-RXAV or ZIG-PS-61
Distance between TX and RX
Full HDBaseT - 328’ or 100M @ 2160P60 4:2:0 8-bit
Copy Protection Compliance
HDCP – Yes – 1.4
Video Bandwidth
10.2 Gbps
Video Timings
480i, 480p, 720p, 1080i, 1080p, 1920x1200, 2K and 4K. 4K/2K, 30Hz 24bpp.
4K/2K, 60Hz, 24bpp with 4:2:0 pixel format
zigencorp.com
Toll Free: 877-650-5252
International: +1 818-654-5252
Audio
Up to Dolby TrueHD and DTS Master Audio
Wall Mountable
Yes – 2 gang Decora style
Color
Black or White
Power Consumption
Less than 5W
Dimensions
5.9 x 2.9 x .95 inches
150 x 74 x 24 millimeters
Weight
.67 pounds
303 grams
Certifications/Compliance
FCC, HDBaseT, CE, RoHS, HDCP, HDMI
Works With
Any properly implemented HDBaseT receiver or switch. Works especially well
with Zigen ZIG-PS-61 presentation switch and ZIG-RXAV-POE HDBaseT
Receiver/Amplifier
6 ZIG-­‐POEWP-­‐100 USER MANUAL Front Side. See items 1-5 on next
few pages
zigencorp.com
Toll Free: 877-650-5252
International: +1 818-654-5252
Panel Description
Front Side
1. Source select – turns blue when HDMI is selected and off when VGA is
selected. Source selection can happen 4 ways:
a.
b.
c.
d.
Last source connected automatically is active and sent to display.
By pushing this button the source will toggle.
Via WebOS that will be covered later.
Via 3rd party control.
2. HDMI Input – Connect HDMI cable here from your source (BlueRay,
Computer, etc.) up to 4K UHD.
3. VGA Input – Connect VGA cable here from PC/MAC or use a breakout
cable to connect Component, Y/C, or composite video sources.
4. CMD Button – this button can be used for almost anything you want – it is
programmed via the WebOS and is accessible via 3rd party control or
WebOS. Use it to set lighting, trigger screen mask or drop screen. If using
with RXAV use one of its relays.
5. Audio Input – 3.5MM stereo audio input jack. The audio going into this
jack follows the VGA/Multi-port
Note: Auto-Switching function – if you remove an active source – and
another source is connected then it will switch to the new source
immediately. Additionally, as soon as you connect either source, if none
are connected, that port will become active immediately.
8 ZIG-­‐POEWP-­‐100 USER MANUAL Rear Side. See items 1-6 on next few
pages
zigencorp.com
Toll Free: 877-650-5252
International: +1 818-654-5252
Rear Side
1. HDBaseT output/LAN Port (fallback) connection – Connect RJ45 up to
100 meters (328 feet) CAT5e, 6, 6a. This is the connection to an
HDBaseT receiver such as the ZIG-POE-RXAV or ZIG-PS-61. You can
also use this connection when accessing via WebOS.
2. 5 VDC Power connection – if NOT using POE power you can connect a
5VDC supply via phoenix style connectors.
Captive Screw Connector – pin outs are also located on the
unit.
2-pin connector – for power
•
•
Power – connect black wire to negative terminal (-)
Power – connect white wire to positive terminal (+)
10 ZIG-­‐POEWP-­‐100 USER MANUAL zigencorp.com
Toll Free: 877-650-5252
International: +1 818-654-5252
General – In the example above we are showing using an HDBaseT transmitter
(ZIG-POEWP-100) connected to the HDBaseT receiver (ZIG-POE-RXAV) – as
mentioned previously you also get an amplified audio output for direct connection
to speakers, LAN ports for almost anything you choose and for controlling/setting
up the devices, relays, a 4K scaler and IR and RS232 control and functionality.
1. Connect sources to POEWP – HDMI and VGA w/Audio
2. Connect RXAV to Display via HDMI
3. Connect Ethernet cable between HDBaseT transmitter (ZIG-POEWP-100)
and RXAV (HDBaseT) Ports – this will also provide power on the ZIGPOEWP-100
4. Note: If you are not using ZIG-POE-RXAV you can also connect directly to
the HDBaseT port on the back of the unit to access/program it.
5. Connect LAN switch/router to LAN 1 port – this is the switch or router that
issues IP address (DHCP server)
6. Connect your PC or MAC to the same switch/router. The DHCP server will
issue IP addresses to both devices separately.
7. Turn on the Source, TV and RXAV
8. Locate the serial number sticker on each RXAV and make note of it. The
web address for the given unit is http://rxav-xxxx/ where the xxxx are the
last 4 digits of the serial number. Ex. If the serial number is
154320000015, then the web address is http://rxav-0015/. This is
necessary to distinguish multiple units from colliding in the network before
their names are changed by the customer. The ZIG-POEWP-100 operates
similarly...i.e. http://poewp-xxxx/.
9. You can also locate the devices with Bonjour. If you do need to connect
directly from a PC or Mac to the LAN 1 or 2 port in the RXAV without a
router (LAN) you can expect up to 5 minutes for the address to be
resolved.
10. Once connected the user interfaces will be available for you to evaluate,
change, enter commands, etc.
12 ZIG-­‐POEWP-­‐100 USER MANUAL ZIG-RXAV-POE Remote Control (comes with ZIG-POE-RXAV)
Perfect for classrooms when connected to the ZIG-POEWP-100 use the remote
to change between HDMI and VGA sources.
•
•
•
•
Trigger devices connected to relays
Mute the audio
Power down the RXAV
Control the Volume
zigencorp.com
Toll Free: 877-650-5252
International: +1 818-654-5252
WebOS Interface Page
Status
Device Name/Notes
Control/ Defaults
Firmware/Res
et/ Info
14 ZIG-­‐POEWP-­‐100 USER MANUAL WebOS
Status
Connections
•
•
•
HDMI – Green when HDMI is the source
VGA – Green when VGA is the source
Audio – Green when audio is present with the VGA signal
Local HDBaseT (RXAV in this case)
•
•
•
•
Link – Green when there is an HDBaseT connection
HDMI - Green when HDMI is present
Mode: Solid green when HDCP is present, flashing green when no HDCP
detected.
Cable Length of CAT cable being reported by HDBaseT chip – this is not
always 100% accurate, especially with shorter cables.
Remote HDBaseT (POEWP in this case)
•
•
•
•
Link – Green when there is an HDBaseT connection
HDMI - Green when HDMI is present
Mode: Solid green when HDCP is present, flashing green when no HDCP
detected.
Cable Length of CAT cable being reported by HDBaseT chip – this is not
always 100% accurate, especially with shorter cables.
Refresh Button – Press to refresh the indicators to note any changes
HDMI and VGA Buttons – Use to toggle between VGA and HDMI
zigencorp.com
Toll Free: 877-650-5252
International: +1 818-654-5252
Device Name & Notes
•
•
Device Name – default out of the box is ZIG-POEWP-100.XXXX (last 4
digits of the serial number). You should change it if you are using more
than 1 device (Change Name below) to whatever you want – ex.
CR100RX – for conference room number 100 receiver.
Notes – free form field for entering installer notes.
Control/Defaults (RS-232 Command Lines)
•
•
•
•
•
•
Button Press – enter the command for the CMD button – use Test and
Save buttons to make sure it works and saved.
HDMI Cable Connect – enter the command that you want to have
executed when an HDMI cable is plugged into the wall plate. Use Test and
Save buttons to make sure it works and saved.
HDMI Cable Disconnect – enter the command that you want to have
executed when an HDMI cable is unplugged from the wall plate. Use Test
and Save buttons to make sure it works and saved.
VGA Cable Connect – enter the command that you want to have executed
when a VGA cable is plugged into the wall plate. Use Test and Save
buttons to make sure it works and saved.
VGA Cable Disconnect – enter the command that you want to have
executed when a VGA cable is unplugged from the wall plate. Use Test
and Save buttons to make sure it works and saved.
NOTE: When assigning and programming via the WebOS you can also
use escape characters – line feed \n and carriage return \r
Firmware/Reset/Info
•
•
•
•
•
•
•
•
Serial Number – serial number of POEWP
Firmware – Current firmware revision
Hardware – for internal use
IP Address – IP address of the unit assigned by your DHCP Server
Device Name – this is what you want to call the unit – syntax example
CR100RX_k123. This is also the name you type into your browser to
access the WebOS.
Factory Reboot – Will reboot the unit.
Choose File/Upload Firmware – when necessary, this is where you select
a new firmware file and upload firmware.
Reset POEWP – will reset the ZIG-POEWP-100 remotely.
16 ZIG-­‐POEWP-­‐100 USER MANUAL •
Install Update – when necessary is for installing new software updates to
the unit.
RS-232 Commands
Command Structure:
ZIG-POE-RXAV RS232 commands
<@hostname> <sp> <command> <sp> <parameter> <end of command>
<@hostname > indicates the specific target RXAV device, preceded by @ <sp>
whitespace, space or tab <command> defines the current operation <parameter>
is the variable or the value passed to the device
<end of command> newline char \n, ASCII 0xA [hex]
Response Structure:
<@hostname> <sp> <parameter> <sp>... <parameter> <sp> <end of
response>
<@hostname> = indicates the device initiating the response <sp> = space, ASCII
0x20 <parameter> = command-specific number of parameters, each followed by
a space 0x20 [hex] <end of response> = newline char \n, ASCII 0xA [hex]
RS232 Protocol Settings:
Baud Rate = 115200 Data Bits = 8 Parity = None Stop Bit = 1
Flow control = None
ZIG-POE-RXAV COMMANDS:
Set volume [range -136dB to +10dB, 1dB steps]
@rxav-01 vol -25
Set device ‘rxav-01’ volume to -25dB Response: @rxav-01 vol x
Increase volume
@rxav-01 volup
Increase device ‘rxav-01’ volume by 1dB Response: @rxav-01 vol x
zigencorp.com
Toll Free: 877-650-5252
International: +1 818-654-5252
Decrease volume
@rxav-01 voldn
Decrease device ‘rxav-01’ volume by 1dB Response: @rxav-01 vol x
Bass level [range -10dB to +10dB in 2dB steps]
@rxav-01 bass 6
Set device ‘rxav-01’ bass level to +6dB Response: @rxav-01 bass x
Treble level [range -10dB to +10dB in 2dB steps]
@rxav-01 treb -2
Set device ‘rxav-01’ treb level to -2dB Response: @rxav-01 treb x
Mute on/off
@rxav-01 mute on
Set device ‘rxav-01’ mute on Response: @rxav-01 mute x
Relay 1 on/off
@rxav-01 rel1 on
Set device ‘rxav-01’ relay 1 to ON position Response: @rxav-01 rel1 x
Relay 2 on/off
@rxav-01 rel2 on
Set device ‘rxav-01’ relay 2 to ON position Response: @rxav-01 rel2 x
Get Device Status
@rxav-01 st
Get device ‘rxav-01’ status Response: @rxav-01 st power x, vol x, bass x, treb x,
mute x, relay1 x, relay2 x
18 ZIG-­‐POEWP-­‐100 USER MANUAL Display Device Info
@rxav-01 man
Get device ‘rxav-01’ device information Response: @rxav-01 Zigen Corp, ZIGPOE-RXAV, fw1 ver xx, fw2 ver yy
Power on/off
@rxav-01 pwr off
Set device ‘rxav-01’ power off Response: @rxav-01 pwr x
ZIG-POEWP-100 COMMANDS:
Source switching (HDMI or VGA)
@poewp-xxxx insel hdmi
@poewp-xxxx insel vga
zigencorp.com
Toll Free: 877-650-5252
International: +1 818-654-5252
Warranty Information
LIMITED WARRANTY – with the exceptions noted in the next paragraph, ZIGEN
warrants the original purchaser that the equipment it manufactures or sells will be
free from defects in materials and workmanship for a period of one year from the
date of purchase. The proof of sale is required in order to claim warranty. Should
this product, in ZIGEN’s opinion, prove defective within this warranty period,
ZIGEN, at its option, will repair or replace this product without charge. Customers
outside of US are responsible for shipping charges to and from ZIGEN. Any
defective parts replaced become the property of ZIGEN. This warranty does not
apply to those products which have been damaged due to accident, unauthorized
alterations, improper repair, modifications, inadequate maintenance and care, or
use in any manner for which the product was not originally intended for. Items
integrated into ZIGEN products that are made by other manufacturers, notably
computer hard drives and liquid crystal display panels, are limited to the term of
the warranty offered by the respective manufacturers. Such specific warranties
are available upon request to ZIGEN.
ZIGEN makes no other representation of warranty as to fitness for the purpose or
merchantability or otherwise in respect of any of the products sold. The liability of
ZIGEN with respect to any defective products will be limited to the repair or
replacement of such products. In no event shall ZIGEN be responsible or liable
for any damage arising from the use of such defective products whether such
damages be direct, indirect, consequential or otherwise, and whether such
damages are incurred by the reseller, end-user or any third party. The
information in this manual has been carefully checked and is believed to be
accurate. However, ZIGEN assumes no responsibility for any inaccuracies that
may be contained in this manual, even if advised of the possibility of such
damages. The technical information contained herein regarding the features and
specifications is subject to change without notice.
20 ZIG-­‐POEWP-­‐100 USER MANUAL 
Download PDF