Movincool | OFFICE PRO 12 | Specifications | Movincool OFFICE PRO 12 Specifications

OPERATION MANUAL
OFFICE PRO 12 / OFFICE PRO 18 / OFFICE PRO 24
READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT
INSTALLATION AND USAGE AND READ ALL SAFEGUARDS
SECCIÒN EN ESPAÑOL
SECTION EN FRANÇAIS
AVAILABLE AT WWW.MOVINCOOL.COM
© 2007 DENSO SALES CALIFORNIA, INC.
All rights reserved. This book may not be reproduced or copied, in whole
or in part, without the written permission of the publisher. DENSO SALES
CALIFORNIA, INC. reserves the right to make changes without prior
notice. MovinCool is a registered trademark of DENSO Corporation.
OPERATION MANUAL
OFFICE PRO 12 / OFFICE PRO 18 / OFFICE PRO 24
Table of Contents
FOREWORD................................................................................. 5
Definition of Terms ............................................................... 5
GENERAL WARNINGS & CAUTIONS ........................................ 6
Inventory ................................................................................ 7
INSTALLATION ............................................................................ 8
Choosing an Installation Site .............................................. 8
Moving the Unit ..................................................................... 9
Plugging in the Unit .............................................................. 10
Warning Signal Connection ................................................. 11
Fire Alarm Control Panel Connection.................................. 11
LCDI Power Cord ................................................................... 12
FEATURES................................................................................... 13
OPERATION................................................................................. 14
Control Panel......................................................................... 14
LCD Indicators ...................................................................... 15
Set Clock …………………………...……...…………………….. 16
Operating in COOL Mode ………...……...……………...……. 16
Operating in Fan Only Mode ……………...……………....….. 16
Changing from Fan Only Mode to COOL Mode ….......…… 16
How to Set a Program ……………………………...………….. 17
How to View and Delete Program ……………...……………. 18
How to Run and Stop Program ………………...……………. 18
Operating Modes ……….………………………...…………….. 19
……………………...…………...…. 20
Empty the Drain Tank
Drain Pump Kit (Optional) …………………...……………….. 21
Self-Diagnostic Codes ……………………...…………………. 22
DAILY INSPECTION & MAINTENANCE ………...……………….. 23
……………………...………...……. 23
Empty the Drain Tank
………………………...……………… 23
Clean the Air Filters
Filter Removal Method ………………………...………………. 23
Filter Cleaning Method ………………………...………….…… 24
In-Season/Off-Season Inspection & Maintenance…....…... 24
TROUBLESHOOTING ……………………………………....………. 25
TECHNICAL SPECIFICATIONS………………………...……..…... 26
FOREWORD
Congratulations on purchasing the MovinCool portable
air conditioner.
This manual explains how to install and operate the MovinCool
Office Pro12, Office Pro18, and Office Pro24 portable
air conditioning units.
Please read this operation manual thoroughly to familiarize
yourself with the features of the unit and to ensure years
of reliable operation.
You may also find it useful to keep this operation manual on
hand for reference. Components and/or procedures are subject
to change without prior notice.
Definition of Terms
!
WARNING : Describes precautions that should be observed
in order to prevent injury to the user during
installation or unit operation.
!
CAUTION : Describes precautions that should be observed
in order to prevent damage to the unit or its
components, which may occur during installation
or unit operation if sufficient care is not taken.
NOTE : Provides additional information that facilitates installation
or unit operation.
5
GENERAL WARNINGS & CAUTIONS
1) All electrical work, if necessary, should only be performed by
qualified electrical personnel. Repair to electrical components
by non-certified technicians may result in personal injury
and/or damage to the unit. All electrical components replaced
must be genuine MovinCool parts, purchased from an
authorized reseller.
2) The proper electrical outlet for MovinCool units must be
equipped with a UL approved circuit breaker.
3) Because of potential safety hazards under a certain condition,
we strongly recommend against the use of an extension cord.
However, if you still elect to use an extension cord, it is
absolutely necessary that it will be a UL listed, 3-wire grounding
type appliance extension cord, having a 3-blade grounding plug
and a 3-slot receptacle that will plug into the appliance.
The marked rating of the extension cord should be 115 V, 15A
for Office Pro 12, and 115V, 20A for Office Pro 18 and 230V, 20A
for Office Pro 24 or equivalent.
4) The Office Pro 12 and Office Pro 18 are equipped with a ten (10)
foot (3 meter) UL approved LCDI power cords. The Office Pro 24
is equipped with a six (6) foot (1.8 meter) UL approved LCDI
power cord. If replacement, fixed location (hard wired) or
power cord lengthening (extension cord) cords are required,
contact your reseller or a qualified electrician for approved
replacement methods.
5) Never fold or place heavy objects on the power cord.
This could result in damage to the power cord causing
electrical shock or fire.
6) Do not place water or any other liquid on the unit. This can
cause damage to the unit and increase the risk of electrical
shock.
7) Do not sit or stand on the unit.
6
INVENTORY
After unpacking your MovinCool unit, please check to make
sure you have the following items :
1) Office Pro 12 or Office pro 18 or Office Pro 24
MovinCool Unit (1)
2) Operation Manual/Product Registration (1)
NOTE : If any of these items were not included in the box or
appear damaged, please contact your MovinCool reseller for
replacement.
MOVINCOOL
MOVINCO
OL
O
O
OFFICE PRO 12 MOVINCOOL UNIT
OFFICE PRO 24 MOVINCOOL UNIT
OFFICE PRO 18 MOVINCOOL UNIT
OPERATION MANUAL/
PRODUCT REGISTRATION
7
INSTALLATION
Choosing an Installation Site
! CAUTION : Following are some precautions to consider before
choosing your installation site. Please review carefully as
improper installation may result in personal injury or damage
to the unit.
1) Do not use the unit in areas where leakage of flammable gas
may occur.
2) Do not use the unit in areas where it will be exposed to rain
or water.
3) Do not use the unit in an atmosphere of excessively corrosive
gas or vapor.
4) Do not use in areas where the temperature is outside the
allowable operating range.
5) Do not install the unit in sloping areas. The unit may move or
topple over even if the casters are set to the LOCKED position.
6) Install the unit in areas that can with-stand the weight of the
unit. The Office Pro 12 unit weighs approximately 200 lbs
(91kg), the Office Pro 18 unit weighs approximately
205 lbs (93kg) and the Office Pro 24 unit weighs approximately
252 lbs (114kg) (when the drain tank is full of water).
7) Allow 18 inches of unobstructed airflow for both the air inlets
and outlets.
8) Do not use the unit at condition above 95°F 60%RH.
8
INSTALLATION(cont.)
Moving the Unit
Unlock the casters and push the MovinCool unit using the side
handles to a flat, level surface and set the casters back to the
LOCKED position.
Right Side Handle
Left Side Handle
MOVINCOO
L
O
UNLOCKED
LOCKED
9
INSTALLATION (cont.)
Plugging in the Unit
1) Check the prong and surface of the power cord plug for
dust/dirt. If dust and/or dirt are present, wipe off with a clean,
dry cloth.
2) Check the power cord, plug and prong for damage or excess
play. If any damage or excess play is found, contact your
MovinCool reseller for repair.
WARNING:
!
1) If the power cord or plug is damaged, repair should only be
performed by qualified electrical personnel.
2) Do not connect/disconnect the power cord or attempt to
operate buttons with wet hands. This could result in
electrical shock.
!
:
CAUTION:
1) Office Pro 12 model ONLY : The AC outlet (115 VAC Single
Phase, 60Hz) needs to be rated at 15A or higher. Do not share
the outlet with any other instrument or equipment.
2) Office Pro 18 model ONLY : The AC outlet (115 VAC single
Phase, 60Hz) needs to be rated at 20A or higher. Do not share
the outlet with any other instrument or equipment.
3) Office Pro 24 model ONLY : The AC outlet (208/230 VAC single
phase, 60Hz) needs to be rated at 20A or higher. Do not share
the outlet with any other instrument or equipment.
NOTE :
1) Make sure the AC outlet is free of dirt, dust, oil, or any other
foreign matter.
2) The Office Pro 12 model is equipped with a UL approved LCDI
cord and an approved NEMA plug configuration (5-15).
The appropriate outlet must be used for this plug type.
3) The Office Pro 18 model is equipped with a UL approved LCDI
cord and an approved NEMA plug configuration (5-20).
The appropriate outlet must be used for this plug type.
4) The Office Pro 24 model is equipped with a UL approved LCDI
cord and an approved NEMA plug configuration(6-20).
The appropriate outlet must be used for this plug type.
10
INSTALLATION (cont.)
Warning Signal Connection (Output Signal terminal L+ and L-)㧖
The controller is equipped with a warning signal output relay type
(Form C, normal open dry contact) which can be used to monitor the
failure condition.
Relay contactor (not connector) is closed when the following
condition has occurred :
a. Tank Full
b. Temperature sensor fails
c. High pressure switch error (model OP24 only)
The relay output contactor is rated 2A at 30VDC or 2A at 30VAC
(resistive load) and it is compatible with various warning devices
such as alarm speaker, light indicators, etc.
Connecting Warning Signal From Controller㧖
1) Remove service panel from the rear of the unit.
2) Push out the back cap from inside. (In case of hand to remove, please
push inner latches of the cap one-by-one)
3) Use recommended warning signal wire size from 16AWG to 26AWG
for a solid wire, or 16AWG to 22AWG for a stranded wire with ring
terminal for #6 stud size.
4) Connect warning device to terminal L+ and L- according to its
polarities.
Fire Alarm Control Panel Connection (Input Signal terminal E+ and E-)㧖
The controller is equipped with a normal open input signal, which can be
connected directly from the fire alarm control panel. When receiving the
signal from the fire alarm control panel, the unit will turn off and will not
turn back until it has been RESET.
Connecting Fire Alarm Control Panel to Controller㧖
1) Remove service panel from the rear of the unit.
2) Squeeze the inner latches and push out the black cap from inside the
panel (See drowing of Cap and inner latch shapes )
3) Use recommended warning signal wire size from 16AWG to 26AWG
for a solid wire, or 16AWG to 22AWG for a stranded wire with ring
terminal for #6 stud size.
4) Connect warning device to terminal E+ and E- according to its
polarities.
㧖This function is not available in OP12 model
Cap
}
}
Latch
11
Input
Signal
Terminals
Output
Signal
Terminals
INSTALLATION (cont.)
LCDI Power Cord Instruction
!
WARNING
The LCDI device is non-serviceable device.
Attempting to open the device may expose the user to hazardous of
electric shock, and could void warranties of this product.
Manufacturer’s reliability is limited to the replacement of the device.
!
CAUTION
1. Read the attention print on the device for proper use and handling
of this device.
2. This device is used for monitoring leakage current.
3. Do not immerse in water.
4. This device must only be plugged into an appropriate wall outlet.
Do not use on extension cords or adapter. Do not remove ground prong.
5. In the event that this device trips, the cause of malfunction should
be corrected first before further use.
6. Using the device beyond recommended voltage poses risk to users.
7. Conductors inside this cord are surrounded by shields, which
monitor leakage current. These shields are not grounded, and they
are periodically examined the cord for any damage. Do not use
this product in the event the shields become exposed.
8. Do not push test and/or reset buttons in a short period.
PROCEDURE
Test device once when AC is installed to assure proper operation.
1. Plug into grounded power receptacle.
2. If light is not on, press reset button once. Light should turn on.
3. Press test button once, light must turn off.
4. Press reset button once again for use. Light should turn on.
5. If test fails, do not use.
<FRONT VIEW>
TYPE 1
TYPE 2
12
FEATURES
For all models:
1) A digital electronic control panel, which allows the user to control
the unit’s operation easily.
2) Dual fan speeds (either HIGH or LOW) in both COOL and Fan Only
modes.
3) Digital LCD display with blue backlight that indicates:
a. Clock with day and time.
b. Room Temperature and Set Point Temperature
(either Fahrenheit or Celsius).
c. Fan Speed Status
d. Cool Mode Status
e. Program Start time and Stop time
f. Program Run and Stop
g. Status Codes
h. Key Locked option
4) The Set point Temperature can be adjusted between 65°F and 90°F
by the SET TEMP buttons.
5) Fire alarm control panel connection ready for automatic
shut off.㧖
6) Automatic shut off and warning signal output and alarm for
temperature sensor failure, cooling failure.㧖
7) A condensate drain TANK FULL indicator (LED) and display (LCD).
8) An automatic restart feature when the power is lost and regained.
The unit will return to the operating mode it was in prior to the loss
of power. Any preset program will be retained in the memory in the
event power loss occurs.
9) A programmable Clock/Timer function. This allows the user to
program a specific time and day that the unit will begin to
operate/start and turn off/end (Automatic Operation).
㧖Not available for OP 12 Model.
13
OPERATION
Control Panel
Before operating the unit, it is important to familiarize yourself
with the basic controls located on the control panel.
PROGRAM
MO TU WE TH FR SA SU
AM
START
STOP
CLOCK
PROGRAM
ON
LOCKED
PM
F
C
HI
LO
ON
COOL
OFF
FAN
RUN/
STOP
F
C
SET TEMP
PROGRAMMING
ROOM TEMP
SET
PROG
8
7
6
TANK FULL
FAN MODE
2
SET
CLOCK
HI/LO
5
SET TEMP
COOL MODE
1
ON/OFF
ENTER
4
3
1) COOL Mode Button
Activates/deactivates the COOL
mode/turns the unit off.
2) FAN Mode Button
Activates/deactivates the HIGH, LOW,
and OFF fan speed.
3) SET TEMP Button (
/
)
Temperature Scale Illuminates to
indicate the current LED temperatures
being displayed are either in °C or °F ;
also displays the clock when
programming.
4) ENTER Button
Press to select set up value
5) SET CLOCK Button
To set clock (day and time)
6) SET PROG Button
To set or view program
7) RUN/STOP Button
Activates/deactivates program(s)
8) TANK FULL LED
Flashes when the drain tank is full.
14
OPERATION (cont.)
Control Panel (Cont.)
LCD Indicators
9
11
12
14
15
16
13
19
10
17
18
9) MO...SU
‫ޓޓޓ‬Illuminates to indicate selected day
‫ޓޓޓ‬of the week
10) °C or °F
Temperature displayed in either Fahrenheit
or Celsius (See Note)
11) AM/PM
Illuminates to indicate AM or PM time of day.
12) PROGRAM
Blinking during program editing mode.
13) PROGRAM ON
Illuminates to indicate program is running.
14) START
Illuminates to indicate program start time.
15) STOP
Illuminates to indicate program stop time.
16) CLOCK
Illuminates to indicate clock status.
17) FAN HI/LO
Illuminates to indicate selected fan speed.
18) COOL ON/OFF
Illuminates to indicate cool on or off.
19) LOCKED
Illuminates to indicate key lock up.
NOTE : ROOM TEMP display range from 16°F to 109°F (-9°C to 42°C)
In Fahrenheit only, when display values is greater than 99°F, it will
display values of +0F (for 100°F), +1F (for 101°F) and +9F (for 109°F)
15
OPERATION (cont.)
Set Clock
Prior to operating the Office Pro 12, 18, or 24 users should set the clock
of the controller to the correct time as shown in the following steps :
1) Press and hold the SET CLOCK
button for 3 seconds or until beep.
(LCD will indicate blinking “CLOCK”
and blinking “Day of the week ”)
AM
HI
LO
ON
COOL
OFF
PROGRAM
PM
ON
LOCKED
F
C
FAN
2) Press SET TEMP buttons to
select day of the week.
PROGRAM
MO TU WE TH FR SA SU
START
STOP
CLOCK
RUN/
STOP
F
C
SET TEMP
PROGRAMMING
ROOM TEMP
SET
PROG
3) Press ENTER button to set Hour.
TANK FULL
FAN MODE
4) Press SET TEMP buttons to select
desired hour.
SET
CLOCK
HI/LO
COOL MODE
5) Press ENTER button to set Minute.
Step 2 to 5
SET TEMP
ON/OFF
ENTER
6) Press SET TEMP buttons to select
desired minute. Press SET CLOCK
button to exit set clock mode.
NOTE: User should check clock periodically to confirm clock accuracy.
Operating in COOL Mode
1) The unit can be operated in COOL mode by pressing the COOL
ON/OFF button (LCD indicates COOL ON).
NOTE : In COOL mode the unit can only be turned off by pressing
the COOL ON/OFF button again, not by pressing the fan buttons.
2) Change the fan speed by pressing the fan HI/LO button.
3) Change the temperature set point by pressing the SET TEMP
buttons (
/
).
NOTE : When turning the unit on, the set point and fan speed are
determined by the last operating mode.
(program mode not included).
Operating in Fan Only Mode
1) The unit can also be operated in Fan Only mode by pressing fan
HI/LO button (LCD indicates FAN HI/LO and COOL OFF).
2) The unit can then be turned off by pressing the fan HI/LO button
until fan turn off (Fan only mode speed sequence are HI→LO→OFF)
Changing from Fan Only Mode to COOL Mode
The COOL mode can be activated while the unit is operating in Fan
Only mode. To do this, simply press the COOL ON/OFF button
(LCD indicates COOL ON).
NOTE : The Fan Only mode will not operate after the COOL mode
has been activated. After the COOL mode has been activated, the
unit cannot be turned off by pressing the fan buttons. The COOL
ON/OFF button must be pressed.
16
Step 1 & 6
OPERATION (cont.)
How to Set a Program
SET START TIME
1) Press and hold the “SET PROG”࡮
button for 3 seconds or until beep.
2) Press “SET TEMP” buttons to select
day of the week.
PROGRAM
MO TU WE TH FR SA SU
AM
START
STOP
CLOCK
HI
FAN
LO
ON
COOL
OFF
PROGRAM
PM
ON
LOCKED
F
C
RUN/
STOP
F
C
SET TEMP
PROGRAMMING
ROOM TEMP
SET
PROG
Step 1 & 18
TANK FULL
3) Press “ENTER” button.
FAN MODE
SET
CLOCK
HI/LO
4) Press “SET TEMP” buttons to select
desired hour.
5) Press “ENTER” button.
COOL MODE
Step 2 to 17
SET TEMP
ON/OFF
ENTER
6) Press “SET TEMP” buttons to select
desired minute.
7) Press “ENTER” button.
SET STOP TIME
8) Press “SET TEMP” buttons to select day of the week.
9) Press “ENTER” button.
10) Press “SET TEMP” buttons to select desired hour.
11) Press “ENTER” button.
12) Press “SET TEMP” buttons to select desired minute.
13) Press “ENTER” button.
SET FAN SPEED
14) Press “SET TEMP” buttons to select desired fan speed.
15) Press “ENTER” button.
SET SET-POINT TEMPERATURE
16) Press “SET TEMP” buttons to select desired temperature.
17) Press “ENTER” button.
EXIT PROGRAM EDITING MODE
18) Press “SET PROG” button to exit program editing mode.
EDIT MULTIPLE PROGRAMS
19)Repeat step 1) to 18) to set up multiple programs.
NOTE: Maximum 7 programming sequences
17
OPERATION (cont.)
How to View and Delete Program
1) Press and hold the SET PROG button for 3 seconds or until
beep.
2) To view edited program - While pressing and holding the SET
PROG button, press SET TEMP ( /
) to scroll program
sequence.
3) To delete a program - Press ENTER and SET PROG buttons
once simultaneously.
4) To delete multiple program - Press and hold ENTER and SET
PROG buttons simultaneously.
How to Run and Stop Program
1) Press RUN/STOP button to activate preset program (LCD
indicates PROGRAM ON). During RUN program, if user push
RESET program run will be terminated, to resume RUN
program user must push RUN/STOP button again.
2) Press RUN/STOP button to stop program.
NOTE :
1) The unit will return to the previous mode if a program is turned off
while it is running.
2) The LCD continues to indicate PROGRAM ON during program
activating.
3) Program can be set during power on standby, during unit running,
or during program running.
4) During programming, the unit returns to the previous mode if no
activity occurs within approximately 3 minutes.
18
OPERATION (cont.)
Operating Modes
The Office Pro 12, Office Pro 18, and Office Pro 24 can be
operated in two modes, Fan Only and COOL. When in Fan Only
mode, the unit circulates the surrounding air. When in COOL
mode, the compressor is operational and cool air is circulated.
1) COOL Mode
Once the compressor has been disengaged for more than 120
seconds, the unit will operate in Fan Only mode for
approximately 5 seconds before the compressor re-engages.
(Time delay setting is around 120 seconds)
2) Temperature Control
The room temperature thermistor monitors the inlet
temperature versus SET POINT temperature and switches
the unit automatically between COOL and Fan Only modes.
3) Fan Mode Control DIP Switch
The Fan Mode Control DIP Switch determines whether the
FAN will continue to operate or stop when the compressor
cycles off. (SET POINT temperature equals inlet air or room
temperature.) The unit has been preset at the factor for
continuous fan operation.
4) Temperature Scale Display DIP Switch
The Temperature Scale Display DIP Switch changes the
temperature(s) that are displayed to either °C or °F .
The unit has been preset from the factory to display the
temperature(s) in °F.
NOTE : If you wish to change the fan mode operation
(COOL_OPERATE to COOL_STOP),
and/or the Temperature Scale
Display (°F to °C), contact your MovinCool reseller.
19
OPERATION (cont.)
Empty the Drain Tank
During COOL mode, condensate will accumulate in the drain tank.
When the drain tank becomes full, the FULL TANK LED will flash
and the LCD displays “Tank FL” and the ALARM signal output
is turned ON * and the unit will shut off automatically.
NOTE : If you want to empty the drain tank, while the unit is in
operation, press the COOL ON/OFF button to turn the unit off.
* Not available for OP 12 model
1) Open the drain tank door.
2) Pull the drain tank from the unit
(display will show “TANK” and
ALARM signal output stays ON).
3) Remove the cap and empty the
drain tank.
CAP
4) Replace the cap and return the drain tank to the unit.
5) Close the drain tank door.
6) Press the COOL ON/OFF button to continue running the unit,
display and ALARM signal will return to normal operation.
20
OPERATION (cont)
Drain Pump Kit (Optinal)
A drain pump kits are available to allow continuous operation
and to eliminate the need for a drain tank.
When the water collects to level
(A) in the pump reservoir, the
drain pump begins to operate
and discharge the water.
NOTE : The compressor will not operate while the drain pump is
discharging in water for the Office Pro 12 and Office Pro 18.
When the water level drops below level (B), the drain pump stops,
and the compressor will restart.
NOTE : If the Fan Mode Control DIP Switch is set to the STOP
position, the entire unit (including fan operation) will turn off
when the drain pump is discharging water.
MOVINCO
OL
&4#+027/2
&4#+027/2
4'5'481+4
O
O
&+5%*#4)'*15'
21
TROUBLESHOOTING
Self-Diagnostic Codes
Self-Diagnostic Codes will be displayed on the Control Board
under the following conditions:
LCD Display Codes
Condition
When the drain tank switch shuts off the unit
LCD displays “TANK FL” and FULL TANK LED
flashes.
Once emptying the drain tank procedure is
completed and “ON/OFF” has been pushed,
unit will return to normal operation.
When the drain pump malfunctions, the
compressor will shut off, and LCD will display
“AS”. Once drain pump is fixed and unit has
been RESET, the unit will return to normal
operation. Contact your MovinCool reseller if
problem persists.
< Office Pro 24 ONLY > When high pressure
switch is activated, display will show “HP” if
high pressure switch is activated 3 times in 24
hours, unit will display blinking “HP” and buzzer
sound will be on. Unit will return to normal
operation after problem is fixed and controller
is RESET (See page 25 troubleshooting section).
Contact your MovinCool reseller if problem
persists.
To RESET press FAN HI/LO and COOL ON/OFF
buttons simultaneously for 3 seconds, controller
will return to normal operation.
When room thermistor becomes open or
shorted, display will show “OPEN RT” or
“SHRT RT” and cool mode operation will be
off. Display and cool mode operation will be
resumed to normal operation after room
thermistor is fixed. Contact your MovinCool
reseller if problem persists.
When freeze thermistor becomes open or
shorted, display will show “OPEN FT” or
“SHRT FT” and cool mode operation will be
off. Display and cool mode operation will be
resumed to normal operation after freeze
themistor is fixed. Contact your MovinCool
reseller if problem persists.
* Not available for OP12
Model
22
DAILY INSPECTION & MAINTENANCE
Empty the Drain Tank
To empty the drain tank, refer to instruction on page 20.
Clean the Air Filters
Clean the air filters once a week. If the unit is used in a dusty
environment, more frequent cleaning may be required. A dirty
air filter can reduce air output resulting in a decrease of the
cooling capacity.
Filter Removal Method
1) Turn the unit off by pressing the COOL ON/OFF button.
If a program is running, you must first press the Program
“RUN” button.
2) Remove the two air filters.
NOTE : To remove the filter from the Office Pro models, open
the front panel and side panel filter doors. On the front panel
door, carefully remove the filter retainer from its clips by
pulling on the retainer at those two points. On the side panel
door, carefully remove the filter element from the wire frame.
FRONT PANEL FILTER DOOR
SIDE PANEL FILTER DOOR
FILTER
WIRE FRAME
23
DAILY INSPECTION & MAINTENANCE (cont.)
Filter Cleaning Method
FI LTER
1) Remove dust from the element with a
vacuum cleaner, or rinse in cold or
lukewarm water. If the element is extremely
dirty, wash with a neutral detergent.
2) After the element has been cleaned, rinse
with clean running water, allow to dry, then
reinstall.
In-Season/Off-Season Inspection & Maintenance
In-Season
1) Check the prongs and surface of the power cord plug for
dust and/or dirt. If dust and/or dirt are present, wipe off
with a clean dry cloth.
2) Check the power cord, plug and prongs for damage or excess
play. If any damage or excess play is found, contact your
MovinCool reseller for repair.
3) Check the air filters and drain tank.
4) Clean the outside of the unit(s) with a damp cloth or mild
nonabrasive cleaner.
Off-Season
1) Operate the unit in Fan Only mode for 8 hours.
NOTE : Operation is necessary to dry out the inside of the unit.
2) Disconnect the power cord from the AC outlet.
3) Check the prongs and surface of the power cord plug for
dust and/or dirt. If dust and/or dirt are present, wipe off
with a clean dry cloth.
4) Check the power cord, plug and prongs for damage or excess
play. If any damage or excess play is found, contact your
MovinCool reseller for repair.
5) Clean the air filters.
6) Empty all water from the drain tank.
24
TROUBLESHOOTING
Check the following items before calling a qualified technician
SYMPTOM
Unit does not operate
POSSIBLE CAUSE
1) Ground fault breaker
trip or LCDI power
cord trip.
Reset Breaker or Reset
power cold
2) Drain Tank is full
(Tank Full LED
will be flashing)
Empty the drain tank
3) High Pressure Activated
10 times in 24hours.
Insufficient Cooling
REMEDY
1) Clean air filter.
2) Check inlet and outlet air,
and make sure that there
were not any object that
may prevent air flow into
or out from the unit.
3) Check environmental
condition whether it is
within operation range
or not.
4) Reset controller
1) Dirty/Blocked air filters
Clean air filter
2) Air Inlet/Outlet blocked
Clean air inlet/outlet
3) Improper temperature setting Adjust temperature setting
If symptoms persist after the above actions have been taken,
turn the unit off, disconnect the power cord plug and contact
your MovinCool reseller.
25
TECHNICAL SPECIFICATIONS
ITEMS/FEATURES
Rating Conditions
Dry bulb
Wet bulb
Humidity
ITEMS/FEATURES
Specification
Power frequency
Line voltage
Power consumption
Current consumption
Power factor
Starting current
Power wiring
Cooling Unit
Cooling capability
Cooling system
Blower
Type of fan
Air volume:Evaporator(High speed)
Condenser(High speed)
Motor output (High)
(Low)
Compressor
Type
Output
Refrigerant Type
Refrigerant Capacity
Safety Devices
Compressor overload protector
Fan moter protector
Anti-freezing thermistor
Full drain tank switch
Automatic Restart(power interruption)
Compressor time delay program
High PressureInterruption
Signal Input/Output
Dimentions & Weight
W˜D˜H(in)
W˜D˜H(mm)
Weight (lbs/kg)
Operating Condition
Inlet air (Relative humidity)
Control Device
Temperature Control
Programmable Timer
Two Speed Fan
Office Pro 12
Office Pro 18
95°F(35°C)
83°F(28.2°C)
(60%)
Office Pro 12
95°F(35°C)
83°F(28.2°C)
(60%)
Office Pro
60Hz
Single phase 115 V
1.40kw
11.2Amps
92%
66A
14(3-core)AWG
2,950kcal/hr
11,800Btu/hr
Direct Expantion
Office Pro 24
95°F(35°C)
83°F(28.2°C)
(60%)
Pro 24
60Hz
Single phase 115 V
1.70kw
15.6Amps
95%
65A
12(3-core)AWG
60Hz
1 phase 208/230 V
2.9/2.9kw
14.2/13.1Amps
99%/96%
62A
12(3-core)AWG
4,230kcal/hr
16,800Btu/hr
Direct Expantion
5,950/6,050kcal/hr
23,600/24,000Btu/hr
Direct Expantion
Centrifugal Fan
Centrifugal Fan
Centrifugal Fan
3
3
3
3
440ft3/min(745m3/h) 540ft /min(917m /h) 630ft3/min(1070m /h)
3
3
3
3
3
870ft
/min(1478m
/h)
770ft
/min(1308m
/h)
820ft /min(1398m /h)
0.57kw
0.24kw
0.14kw
0.40kw
0.17kw
0.08kw
Hermetic Rotary
0.8kw
R-22
0.95lbs(0.43kg)
Hermetic Rotary
1.16kw
R-410A
1.70lbs(0.77kg)
Hermetic Rotary
1.83kw
R-410A
1.98lbs(0.90kg)
Include
Include
Include
Include
Include
Include
N/A
N/A
Include
Include
Include
Include
Include
Include
N/A
Include
Include
Include
Include
Include
Include
Include
Include
Include
21”×27”×44”
538×685×1118
165/75
21”×27”×44”
538×685×1118
170/77
21”×27”×47”
538×685×1194
216/98
95°F(35°C) 60%
65°F(18.3°C) 50%
Include
Include
Include
26
95°F(35°C) 60%
65°F(18.3°C) 50%
Include
Include
Include
95°F(35°C) 60%
65°F(18.3°C) 50%
Include
Include
Include
THE #1 SPOT COOLING SOLUTION
.+/+6'& 9#44#06;
DENSO SALES CALIFORNIA, INC. (“DENSO”) warrants its MOVINCOOL
Products only to the extent stated in its official written warranties. Unless
otherwise specifically provided in writing by DENSO, DENSO warrants to enduser that the Products shall be free of defects in materials or workmanship and
will function in accordance with DENSO’s published specifications under
ordinary intended use and service for a period of twelve (12) months
after delivery to the end-user ; provided, however in the case of the compressor
element of the Products such warranty shall be for a period of thirty six (36)
months after delivery to the end-user. DENSO shall, at its sole option, repair or
replace any defective Product covered by this warranty. Such remedy shall be
end-user’s sole remedy with respect to any particular defect in the Products.
This warranty does not cover defects or malfunctions which result from
causes beyond DENSO’s control, including, without limitation, (‫)ޓ‬
i unusual
physicalor electrical stress ; ( ii ) accident, neglect, abuse, misuse or other
abnormal use ; ( iii ) failer to perform routine maintenance in accordance with
DENSO’s recommended procedures ; ()
iv normal wear and tear ; ( v ) repairs or
attempted repairs by an unauthorized person ; ( vi )modifications or alterations
to the Products ; ( vii)use with supplies or devices not supplied or approved by
DENSO ; or ( viii) improper servicing. This warranty shall extend only to the original
end-user and shall be void if any labels or other identifying marks permanently
affixed to Products when shipped by DENSO are removed, altered, defaced or
obliterated.
.
The aforesaid warranty is the only warranty made by DENSO with respect to the
Products and is in lieu of all obligations or liabilities on the part of DENSO for
damages arising out of or in connection with the sale, use or performance of
the Products, including, without limitation, any lost profits or any other
concequential, incidental, special or exemplary damages of any kind.
DENSO DISCLAIMS ALL OTHER WARRANTIES WITH REGARD TO THE
PRODUCTS, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR USE. THERE ARE NO WARRANTIES WHICH EXTEND
BEYOND THE DESCRIPTION CONTAIND HEREIN.
PURCHASE DATEAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
:
SERIAL NUMBERAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
:
DENSO SALES CALIFORNIA, INC.
3900 Via Oro Avenue
Long Beach CA 90810-1868
800-264-9573 / 310-834-6352
www.movincool.com
P/N : GX484007- 2111
Second Issue : June 2007
Download PDF