Royal Sovereign | RSL1062 | Owner`s manual | Royal Sovereign RSL1062 Owner`s manual

OWNER'S MANUAL
RSL1062 Laminator
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Support tab on www.royalsovereign.com
Royal Sovereign International Inc.
www.royalsovereign.com
TABLE OF CONTENTS
TOPIC
PAGE
1. Introduction........................................................................................................................................ 2
2. Safety Precautions.............................................................................................................................. 2
3. Product Identification.......................................................................................................................... 3
4. Included with Laminator...................................................................................................................... 4
5. Loading Film........................................................................................................................................5
6. Threading Film
6.1. Hot Film.................................................................................................................................... 6-7
6.2. Cold Film...................................................................................................................................... 8
6.3. Mounting...................................................................................................................................... 9
7. Control of Roller Pressure ............................................................................................................... 10
8. Control Panel.................................................................................................................................... 11
9. Laminating Steps
9.1. Hot Laminating..................................................................................................................... 12-13
9.2. Cold Laminating......................................................................................................................... 14
10. Using Cross Cutter......................................................................................................................... 15
11. Maintenance................................................................................................................................... 16
12. Troubleshooting.............................................................................................................................. 17
13. Recommended Temperature and Speed Settings........................................................................ 18
14. Specifications.................................................................................................................................. 19
15. Warranty.......................................................................................................................................... 20
1
RSL-1062
1. INTRODUCTION
Thank you for choosing a Royal Sovereign laminator. It has been designed and manufactured to provide years
of continuous service. For complete operating and maintenance information please read this manual
thoroughly. Upon receipt of your laminator, please inspect the box, the machine and all other contents for
shipping damage. Damage should be brought to the immediate attention of the delivering carrier (See page 3
for list of shipment elements).
2. SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury. Please read the
instructions carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. E
nsure the unit is plugged into a properly grounded outlet with the correct voltage.
3. K
eep hands and clothing (i.e. Neckties) away from rollers.The rollers have pinch points that can trap body
parts or clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. E
nsure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing.
8. Keep out of reach of children.
9. O
nly Royal Sovereign authorized maintenance and service technicians should make repairs.
10. D
o not attempt to laminate items that exceed total recommended material thickness for the unit
11. When cleaning the machine, don't use flammable sprays or materials.
12. D
o not touch the rollers when they are hot or place foreign objects inside the machine.
13. D
o not cover the surface of the machine until the machine has completely cooled.
2
3. PRODUCT IDENTIFICATION
2
1
12
3
4
5
10
11
6
8
9
7
NO
1
PART NAME
NO
PART NAME
UPPER FILM
7
LOWER FILM
TAKE-UP BOBBIN
8
GUIDE-DOCUMENT
2
3
IDLE BAR
9
HANDLE-TENSION
4
HOT ROLLER
10
PRESSURE LEVER
5
SAFETY COVER
11
CONTROL PANEL
6
FRONT-TABLE
12
KNOB-TENSION
3
RSL-1062
4. INCLUDED WITH LAMINATOR
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are reported and a claim is
filed with the reseller immediately upon receipt of shipment.
Part Name
Owner's Manual
2" (57mm)/3”(76mm) Auto Grip
Quantity
1
4/6
L-wrench (2.5)
1
L-wrench (6)
1
Dust Cover
Motor Fuse (50T) 6.3A
Silicone Rubber
1
1
4
Main Power Fuse(65TS)15A
1
Roll Film Samples
2
4
Picture
5. Loading Film
Picture 1
Picture 2
Picture 3
Picture 4
1. As shown in picture 1, insert auto grips onto the upper/lower film shaft.
2. As shown in picture 2, using the special tool, fix the auto grips on the
film shaft with set-screws.
3. Set the glossy side of the upper and lower film towards the heat rollers.
( Glossy side is PET film and matte side is thermal polymer laminating
adhesive)
4. Center film as shown in picture 3 and 4.
5
RSS, RSR, RSL-1062
RSH Series
6. THREADING FILM
6.1. HOT FILM
;66+88522,/23
'*.+9/<+9/*+
;66+8/*2+('8
8522
-2599?9/*+
'*.+9/<+9/*+
-2599?9/*+
25=+88522,/23
9+)54*/*2+('8
,/89:/*2+('8
1. Turn the power switch on("I" position). Power switch
is located in the rear of the unit on the left side.
2. Complete the "Loading Film" steps as shown on
page 4.
3. Set the temperature and speed according to the Recommended Temperature and Speed section.
4. Remove the Front Table.
5. Pull down the upper film over the Safety Cover to the lower film; align and center the lower film to upper film (Picture 1).
Picture 1
6. Rewind the upper film until the film aligns with the Safety Cover.
7. Thread the film over the Upper Idle Bar and underneath the Safety Cover until the film rests on the upper roller (Picture 2).
Picture 2
6
8. Carefully pull up the laminate from the lower roll up towards the first idle bar and then around the back side of the second Idler (Caution: lower roller may be hot).(Picture 3)
9. Tack the lower film to the upper film that is resting on the main roller (Picture 4).
10. Reinstall the Front Table and close the Safety Cover.
Picture 3
11. Adjust the nip setting to 1/4'' (6mm).
12. Insert and push the leader boards on each end until boards reach the front nip point.
13. Adjust the nip setting to "Laminating" mode.
14. Push the Run button.
15. Push the leader boards between the pair of main rollers (Picture 5).
Picture 4
16. Press the Run button and adjust the supply roll
tension knobs by rotating clockwise or counterclockwise. Turn it until the supply roll films have some resistance (the tension varies depending on the film thickness; the thicker the film the more tension is required) (Picture 6).
17. Press Stop button when the leader board has completely exited the rear of the unit.
Picture 5
18. Use the Cross Cutter to cut the leader board from the web (see page 18).
19. Peel Trim any excess film off of the leader board edges. The leader board can be reused.
20. Set the roller nip setting to the appropriate position for the lamination or encapsulation application.
Picture 6
7
RSS, RSR, RSH
RSL-1062
Series
6.2. COLD FILM
:'1+;6*+</)+
)52*,/23
6'6+8(')1
;66+8/*2+('8
8522
(')1/4-6'6+8
('9+,/23
25=+8/*2+('8
1. Follow the steps in the "Loading Film" procedure by loading the upper shaft with pressure sensitive film, e.g. (Royal Print-Pro Film) and lower shaft with pressure sensitive mounting adhesive films or backing paper
(Royal Sovereign White-Mount or Clear-Mount).
2. Pull the upper laminate under the upper idle bar and separate the release liner
from the laminate.
3. Tape the release liner to the Take-Up Paper Core and allow the laminate to hang
over the main rollers.
4. Pull up the mounting adhesive and tack it to the laminate hanging over the rollers
(do not use the Lower Idle Bar).
5. Reinstall the Front Table, and close the Safety Cover.
6. Adjust the nip setting to 1/4"(6mm).
7. Insert and push the leader board until board reaches the nip point.
8. Press the Run button and adjust the supply roll tension knobs by rotating clockwise or counterclockwise. Turn it until the supply roll films have some resistance
(the tension varies depending on the thickness of a film; the thicker the film the more tension is required).
9. Press Stop button when the leader board has completely exited the rear of the unit.
11. Use the Cross Cutter to cut the leader board from the web (see page18).
12. Set the roller nip setting to the appropriate position for the lamination application.
8
6.3. MOUNTING
1. L ay the decaled image face down on a flat surface. Carefully peel back
and put a crease along the edge of the release liner (Approximately 1 inch
or 25mm, Figure 1).
Figure 1
2. W
ith the image facing up, align the image onto the board. Press firmly
from the center out (Figure 2).
Figure 2
3. A
djust the pressure lever to ensure the proper opening (Figure 3).
4. F
lip the image over the upper roller and hold on to the release liner
(Figure 4).
5. P
ress the foot pedal once, and then let it go while slowly pulling the
release liner as the board enters the main roller nip (Figure 5).
Figure 3
Figure 4
Press the foot pedal once again when the board has completely exited
from the rear of the unit.
Trim the board if necessary.
Figure 5
9
RSS, RSR, RSH
Series
RSL-1062
7. CONTROL OF ROLLER PRESSURE
3
4
5
6
2
1
To set, pull the pressure lever outward and turn to one of the following positions.
① OPEN: For detaching and cleaning rollers.
② 6MM: For laminating 6mm[0.24in] thick board.
③ 5MM: For laminating 5mm[0.2in] thick board.
④ 3MM: For laminating 3mm[0.12in] thick board.
⑤ 1.5MM: For laminating 1.5mm[0.06in] thick board.
⑥ LAMINATING: For laminating 25~250micron(1~10mil) thick film and cold film.
10
8. CONTROL PANEL
1. UPPER: To change upper roller temperature
by pressing button, then up or down arrow.
(range 32~302°F or 0~150°C)
2. LOWER: To change lower roller temperature by pressing
button, then up or down arrow.
(range 32~302°F or 0~150°C)
3. SPEED: To change speed of the rollers by pressing
button, then up or down arrow. (range 1 through 9)
4. MEMORY: To recall or change presets.
To recall the settings, press MEMORY
then up or down arrow. To save the settings,
set desired temperatures and speeds then
press the MEMORY button twice.
(stores up to 9 different settings)
5. C/HOT: To change the mode from hot to cold or cold to hot lamination. In cold mode, the speed defaults
to 2 (speed 1~4 settings) and stand-by function is disabled.
6. T-CHECK: To check current upper and lower roller temperatures.Display automatically returns to the
previous settings after 5 blinks.
7. ST/BY: To change to stand-by mode (temperature will automatically reset to 176°F (80°C). While in this
mode, all the buttons on the control panel are disabled. Press ST/BY mode button to resume normal
operation.
NOTE: Auto stand by mode and auto power off mode
-Stand by mode: If no activity is made within 2 hours after each use the machine will automatically switch
into stand by mode.
-Auto power off mode: If the machine is in stand by mode and no activity is made for 60 minutes the
machine will automatically power off.
-If any activity is made while in stand by or auto power off mode the machine will return to it's previous
stage.
8. REV: To reverse the rollers. Must press and hold the button to activate.
9. STOP: To stop the rollers from turning.
10. RUN: To start the rollers .
11. FAN: To activate the cooling fans.
11
RSS, RSR, RSH
RSL-1062
Series
9. LAMINATING STEPS
9.1. HOT LAMINATING
1. Turn on the power switch located on the rear of the machine.
2. Set the pressure lever to the "Laminating mode".
3. Increase the roller temperature. If you already have a setting in the memory that
you want to use press the
button and then the
or
buttons to
select your desired setting.
4. When the desired temperature is met "READY" will be displayed on the screen and
you will hear a beep.
5. Press the
button. The rollers should begin to turn, if they do not turn make sure
the safety cover is closed or check the troubleshooting section of the manual.
6. Use the upper and lower Tension knobs to properly adjust the tension of the roll film.
Having the tension too tight will slow down or prevent the rollers from turning and if
the tension is set too low this can cause wrinkles in your lamination.
7. For ease and convenience set the document guides in position.
8. Set document on the table. You should allow at least 5mm(1/4") space on each
side for perfect lamination.
9. Press the
button when lamination is competed.
10. When lamination is completed your item may be hot and can easily bend. Lay on a
flat surface to properly cool.
11. When you have completed all of your lamination, set the pressure lever to the OPEN
position.
12. Turn the Power switch off.
12
— Useful Information —
1. You can preset up to 9 temperature and speed settings in the memory for faster
easier use.
2. When laminating continuously "WAIT" may appear on the display, if this occurs
lower the speed by 1 increment, "READY" should appear and you may continue
laminating.
3. When laminating a document much smaller than the film, place the document in
the center of the film for better lamination results.
4. When laminating at high temperatures (> 248°F/120°C) you may want to press
the FAN button to allow the cooling fan to cool the document being laminated.
5. When laminating continuously High Temperature may appear,if this ocuurs
lower the speed or lower the temperature or stop for a minuate.
13
RSS, RSR, RSH
RSL-1062
Series
9.2. COLD LAMINATING
1. Put cold roll film on upper shaft. Load backing paper on the lower shaft as per
illustration 6.2 on page 7.
2. Pull COLD film and fix it so that the Release Liner can be wound on take-up
mandrel clockwise. (Revolve core to make Release Liner a little tight)
3. Set pressure lever to the proper position according to your laminating condition.
4. After pressing the
button, choose and
set proper speed by using the
and
button.
5. It is
when ready is dispalyed
on the screen and beeps three times.
6. Turn on the take up device and set
the proper film tension by pressing
the"RUN "button. Lower tension
would make better operation.
7. Center the document on the table.
For ease and convenience set the
document guides in position
8. Press the"RUN "button and "take up
motor" at the same time.The liner and film
will roll at the same time.
9. When lamination is completed, press the
button.
10. Set pressure lever at the "OPEN" mode.
11. Turn off the power switch.
14
10. USING CROSS CUTTER
The cross cutter is located on the rear exit table of the machine.
1. After lamination, move the cutter
approximately to the center of the
completed application at the desired point
of detachment (Figure 1).
Figure 1
2. Grasp film with one hand, press the cutter
downward into the application and slide it
first to one end of the application, then to
the other end to complete the cut.
(Figure 2 & 3)
Figure 2
Figure 3
15
RSL-1062
RSS, RSR, RSH
Series
11. MAINTENANCE
Cleaning the Body of the laminator
To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.
Removing Adhesive Build Up
1. Remove the film from the laminator.
2. Use a damp (water only) cloth and a rubber gum eraser to remove
the adhesive on the Teflon (metal) and silicone rollers.
NOTE: Rub firmly but do not scrub the rollers vigorously as this may
scratch the surface. Do not use sharp metal objects, steel wool,
or abrasive, as these may also damage the rollers.
16
12. TROUBLESHOOTING
Symptom
Possible Solution
Cause
a. Power switch is in "0"
Machine will
not turn on:
the "I" (On) position
(Off) position
b. Tripped circuit breaker.
c. Blown main power fuse.
a. Safety cover is not closed.
There is power, but the
rollers are not turning after the b. Paper guide is not installed
correctly.
"RUN" button is
c.
Blown
motor fuse.
pressed:
The unit is not heating up
a. The machine is in "COLD"
mode.
b. Set temperature is lower
than the room temperature.
Curled lamination:
a. Upward curl.
b. Downward curl.
Unclear lamination:
a. Put the power switch to
b. Reset the circuit breaker.
c. Replace the fuse.
a. Close the safety cover to
active the safety switch.
b. Properly install the paper
guide so that the micro
switch is activated.
c. Replace the motor fuse.
a. Switch to "HOT" mode.
b. Raise the temperature
according to the
recommended film
temperature.
a. Loosen the top roll film
tension.
b. Loosen the bottom roll
film tension.
The main roller temperatures are too Raise the roller
low and/or lamination speed is too temperatures and/or
lower the lamination speed.
fast.
17
RSS, RSR, RSH
RSL-1062
Series
13. Recommended Temperature and Speed Settings.
NO
Film thickness
1
38 micron
(1.5 mil)
100 C
o
(212 F)
2
75 micron
(3 mil)
105 C
o
(221 F)
3
80 micron
(3.2 mil)
105 C
o
(221 F)
4
100 micron
(4 mil)
110 C
o
(230 F)
5
125 micron
(5 mil)
120 C
o
(248 F)
6
150 micron
(6 mil)
125 C
o
(257 F)
7
175 micron
(7 mil)
130 C
o
(266 F)
8
200 micron
(8 mil)
135 C
o
(275 F)
9
250 micron
(10 mil)
140 C
o
(284 F)
Temp
Preset
Speed
Func'No
User
Temp Speed
o
5
1
4
2
5
3
4
4
5
5
3
6
4
7
3
8
3
9
o
o
o
o
o
o
o
o
NOTE: Speed and temperature should be adjusted in accordance with film
manufacturer's recommendations.
18
Remark
14. SPECIFICATIONS
Description
RSL-1062
Power
AC 220~230V
Powersupply
supply
AC 220~230V
50/60Hz50/60Hz
Power consumption
2400W
Max. laminating width
Film thickness
Max. laminating speed
Ready time
Heating method
Hot roller
Driving motor
DC geared
Max. Temperature control
Speed control
Transport type
4 Roller
Film core size
Auto grip (2",3")
Cooling system
2 AC FAN
Cross cutter
Yes
1060mm / 41.7"
25~250 mic / 1~10mil
2.5m/min / 8.2ft/min
11min
150°C / 302°F
9 settings
Hot lamination
Yes
Cold lamination
Yes
Mounting thickness
6mm / 0.24"
Take up system
Chain link to main motor
Reverse
Unit dimensions
(w x d x h)
Unit weight
Carton dimensions
(w x d x h)
Yes
1354×662×1165(mm)
53.3"×26"×45.9"
130kg
1570×785×565(mm)
61.8"×30.9"×22.2"
Gross weight
148kg
19
RSL-1062
15. WARRANTY
Royal Sovereign International warrants the equipment sold is free from defects in material and
workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding
lamination rollers which are warranted for Six (6) months. This warranty is extended only to the original
purchaser. This warranty is the only warranty made by Royal Sovereign International and cannot be
modified or amended. Royal Sovereign’s sole and exclusive liability and the customer’s sole and exclusive
remedy under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such defective
part or product. These remedies are only available if Royal Sovereign’s examination of the product
discloses to Royal Sovereign’s satisfaction that such defects actually exist and were not caused by misuse,
neglect, attempt to repair, unauthorized alternation or modification, incorrect line voltage, fire, accident,
flood or other hazard.
All warranty claims must be filed through the authorized Royal Sovereign dealer or reseller through which
the equipment was originally purchased. Model, serial number and date of delivery are required for all
claims.
The warranty made herein is in lieu of all other warranties, expressed or implied, including any warranty or
merchantability or fitness for a particular purpose. Royal Sovereign will not be liable for personal damage or
personal injury (unless primarily caused by its negligence), loss of profit, or other incidental or
consequential damages arising out of the use or inability to use this equipment.
LIMITED WARRANTY
This warranty specifically does not cover damage to laminating rollers caused by knives, razor blades, or
any sharp objects or abrasives, or failure caused by adhesives, or damage caused by lifting, tilting or
improper use of the machine. Warranty repair or replacement by Royal Sovereign or its authorized
Reseller(s) does not extend the warranty beyond the initial one year period from the date of installation.
Unauthorized customer alterations will void this warranty.
CORPORATE HEADQUARTERS
Royal Sovereign International Inc.
2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.
TEL : +1) 800-397-1025
FAX : +1) 201-750-1022
E-mail : info@royalsovereign.com
Royal Sovereign Inc. <Oversea Sales Office>
RS Holland B.V.
Planetenweg 75 2132HM Hoofddorp, The Netherlands.
TEL : +31) 23-5626620, +31) 23-5654451
FAX : +31) 23-5654565
E-mail : purchaseorder@royalsovereign.com
1001, World Meridian II, 426-5, Gasan-dong,
Geumcheon-gu, Seoul, 153-759, KOREA
TEL : +82)2-2025-8800 FAX : +82)2-2025-8830
E-mail : sales@royalsovereign.com
RS Canada Inc.
RS International Australia PTY. LTD.
30 Prime Drive, Seven Hills, NSW 2147, Australia
TEL : +61) 2-9674-2127
FAX : +61) 2-9674-2027
E-mail : salesaust@royalsovereign.com
164 Oakdale Road, Toronto, Ontario M3N 2S5 CANADA
TEL : +1 ) 416-741-8400 FAX : +1 ) 416-741-8185
E-mail : info@royalsovereign.com
20
Download PDF