Installing your ST1.2 Series CompactFlash model disc drive ST1.2 Series Installation Guide ST68022CF, ST68022FX, ST66022CF, ST66022FX, ST64022CF, and ST64022FX CompactFlash/Flex Interface Disc Drives Publication Number: 100375653, Rev. A, May 2005 The easiest way to install your ST1.2 Series drive Many of today’s consumer products, like cameras, notebook computers, MP3 players, printers and more have been designed to make it possible for the end user to use CompactFlash interface devices. Your Seagate® ST1.2 Series drive is designed for such use. Refer to your product’s user manual for the location of the CompactFlash media compartment and the specific instructions regarding insertion and removal of removable media devices like the ST68022CF, ST66022CF and ST64022CF models. Your product manufacturer’s support Web site will have the most up-to-date information. Read and follow all instructions regarding the proper steps to be taken when using your Seagate ST1.2 Series disc drive. The Seagate ST1.2 Series Flex interface disc drive models, ST68022FX, ST66022FX and ST64022FX, are designed for embedded installation or as a fixed storage solution. Follow the installation instructions provided on this instruction sheet. Your product manufacturer’s support Web site will have the most up-to-date information on installing and removing storage devices. Read and follow all instructions regarding the proper steps to be taken when using your Seagate ST1.2 Series disc drive. It is important to follow the handling precautions and electrostatic discharge protection information below when handling any electronic device. It is always a good idea to back up all your data before installing any new hardware in your computer. Each product, which utilizes CompactFlash storage devices, has its own unique removable media compartment. Refer to the product’s user manual to locate the media compartment and for instructions on removing and installing media devices. Warning. It may be necessary to turn off the product. Refer to your product’s operator manual for cautions, warnings and recommendations on the installation and removal of media devices. Note. This drive is designed for a product that supplies interface signals and +3.3V power through the CompactFlash connector. Refer to your consumer products manual to determine if your Seagate ST1.2 Series disc drive is compatible. See Figure 2 for drive dimensions. FINGER GRIP Breather Hole Do not cover E Figure 1 S1.2 FX interface drive ST1.2 Series—Finger grip areas Drive characteristics Formatted capacity Total number of sectors* Cache size Formatted capacity Total number of sectors* Cache size ST68022CF 8.0 Gbytes 15,625,008 2 Mbytes ST68022FX 8.0 Gbytes 15,625,008 2 Mbytes B D Bottom View C A N Bottom J K H Top L Pin 50 Pin 1 A B C D E F G H J K L M N Figure 2 M CF Dimension Table Inches Millimeters 0.197 ± .004 5.00 ± .10 1.433 ± .006 36.40 ± .15 1.685 ± .004 42.80 ± .10 1.015 ± .003 2x 25.78 ± .07 1.152 ± .010 29.25 ± .25 0.299 ± .010 7.61 ± .25 0.394 min 10.00 min 0.063 ± .002 1.60 ± .05 0.040 ± .003 2x 1.01 ± .07 0.039 ± .002 1.00 ± .05 0.039 ± .004 2x 1.00 min 0.065 ± .004 1.65 ± .10 0.243 ± .004 2x 6.16 ± .10 ST1.2 Series, CF+ dimensions—end, top, and side views Installing your ST1.2 Series Flex interface model disc drive Finger Grip Area S1.2 CF interface drive Recommended case temp. measurement location F Handling precautions/electrostatic discharge protection • ST1.2 Series disc drives are fragile. Do not drop or jar the drive. Handle the drive only by the edges or by the finger grip area shown in Figure 1. Keep the device in the packaging until you are ready to install it and between uses to minimize handling damage. • It may be necessary to turn off the power to the host product during installation. Refer to your product’s user manual for details regarding installation and removal of media devices. • Do not disassemble the drive. Doing so voids the warranty. See the warranty information on page 2. • Do not expose the drive to extreme temperatures or humidity conditions. • Do not apply pressure, write on, or attach labels to the top or bottom of the drive. • Do not cover or otherwise obstruct the breather hole on the top of the drive. (See Figure 2 and Figure 3) • Keep the drive away from strong magnetic fields to avoid data loss. G ST66022CF 6.0 Gbytes 11,719,008 2 Mbytes ST66022FX 6.0 Gbytes 11,719,008 2 Mbytes ST64022CF 4.0 Gbytes 7,999,488 2 Mbytes ST64022FX 4.0 Gbytes 7,999,488 2 Mbytes *One sector equals 512 bytes. Note. The Seagate ST1.2 Series CompactFlash disc drive is compatible with the CF+ and CompactFlash Specification 2.0. Note. The Seagate ST1.2 Series Flex interface disc drive is compatible with the ATA version 7. Follow installation instructions for media devices provided in your product’s user manual to determine if your Seagate ST1.2 Series disc drive is compatible. See Figure 3 for drive dimensions. Follow all handling precautions/ electrostatic discharge protection suggestions when installing any drive. Follow the precaution when installing and removing your ST1.2 Series Flex interface disc drive: • Drive electronics are extremely sensitive to static electricity. Caution should be exercised when handling any electronic device. Wear an Electrostatic Discharge (ESD) ground strap when integrating the flex cable into host systems. Improper handling may cause ESD damage to the ST1.2 Series disc drive’s electronics. • Do not bend the cable sharply as this may cause the electrical traces to be broken. See Figure 4. • When the drive is powered on, do not physically remove the flex cable from the host connector. Power down the system first before removing the drive . Recommended case temp. measurement location G FINGER GRIP A F Breather Hole Do not cover Seagate support services For online information about Seagate products, visit www.seagate.com or e-mail your disc questions to DiscSupport@Seagate.com. If you need help installing your drive, consult your dealer first. If you need additional help, call a Seagate technical support specialist. Before calling, note your system configuration and drive model number. Africa +1-405-324-4714 Netherlands 00 800-47324283 Australia 1800-14-7201 New Zealand 0800-443988 Belgium 00 800-47324283 Norway 00 800-47324283 China* 800-810-9668 Poland 00 800-311 12 38 Denmark 00 800-47324283 Spain 00 800-47324283 France 00 800-47324283 Sweden 00 800-47324283 Germany 00 800-47324283 Switzerland 00 800-47324283 Hong Kong 800-90-0474 Singapore 800-1101-150 Hong Kong† 001-800-0830-1730 Taiwan* 00-800-0830-1730 India 1-600-180-1104 Thailand 001-800-11-0032165 Indonesia 001-803-1-003-2165 Turkey 00 800-31 92 91 40 Ireland 00 800-47324283 United Kingdom 00 800-47324283 Italy 00 800-47324283 USA/Canada/ 1-800 SEAGATE or Japan 0034 800 400 554 Latin America +1-405-324-4700 Korea 007 98 8521 7635 Other European Malaysia 1-800-80-2335 countries +1-405-324-4714 Middle East +1-405-324-4714 E B Bottom View D R Pin 45 S Pin 1 P C Bottom H T J *Mandarin †Cantonese K L Top M A B C D E F G H J K L M P R S T Figure 3 FX Dimension Table Inches Millimeters 0.197 ± .004 5.00 ± .10 1.433 ± .006 36.40 ± .15 1.685 ± .004 42.80 ± .10 1.015 ± .003 2x 25.78 ± .07 1.152 ± .010 29.25 ± .25 0.299 ± .010 7.61 ± .25 0.394 min 10.00 min 0.063 ± .002 1.60 ± .05 0.040 ± .003 2x 1.01 ± .07 0.039 ± .002 1.00 ± .05 0.039 ± .004 2x 1.00 min 0.065 ± .004 1.65 ± .10 0.906 ± .003 23.00 ± .07 0.669 ± .020 17.00 ± .50 0.414 ± .020 10.51 ± .50 0.130 ± .004 2X 3.30 ± .10 ST1.2 Series, FX dimensions—end, top, and side views 5.5 mm Bend Radius Hard Disc Corners Assembly Stiffener Mounting Drive PCB Contact Pad Face Down Host PCB Flex cable 17 mm Hard Disc Assembly Note. If these tips do not answer your question or solve the problem, contact your dealer or visit http://seatools.seagate.com to download SeaTools™ disc diagnostics software and more troubleshooting advice. Breather Hole (do not cover) Bend Radius Corners Warranty. To determine the warranty status of your Seagate disc drive, contact your place of purchase or visit our web site at www.seagate.com for more information. Return Merchandise Authorization (RMA). Run SeaTools to diagnose your drive before requesting a return authorization. In addition, please verify that your drive is defective by following the troubleshooting checklist in this guide. Seagate offers comprehensive customer support for all Seagate drives worldwide. Seagate customer service centers are the only facilities authorized to service Seagate drives. Drive return procedures vary depending on geographical location and are subject to current international trade regulations. Shipping the drive Caution. Back up the data before shipping. Seagate assumes no responsibility for data lost during shipping or service. Shipping drive in an unapproved container voids the warranty. Pack the drive with original box and packing materials. Use no other materials. This prevents electrical and physical damage in transit. Electromagnetic compliance for the European Union. This model complies with the European Union requirements of the Electromagnetic Compatibility Directive 89/ 336/EEC of 03 May 1989 as amended by Directive 92/31/EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993. Compliance of this drive, as a system component, was confirmed with a test system. We cannot guarantee that your system will comply. The drive is not meant for external use (without properly designed enclosure, shielded I/O cable, etc.). Sicherheitsanleitung 1. Das Gerrät ist ein Einbaugerät, das für eine maximale Umgebungstempeatur von 70°C vorgesehen ist. 2. Als Versorgungsspannugen werden benötigt: +5V +/- 10% 0.330mA; +3.3V +/- 5% 0.330mA 3. Die Versorgungsspannung muss SELV entsprechen. 4. Alle Arbeiten auf dem Festplattte dürfen nur von Ausgebiletem Serciepersonal durchgeführt werden. Bitte entfernen Sie nicht die Aufschriftenschilder des Laufwerkes. 5. Der Einbau des Laufwerkes muss den Anforderungen gemäss DIN IEC 950 VDE 0805/05.90 entspreche. Drive PCB Mounting Minimum 1 mm Stiffener Figure 4 Contact Pad Host PCB Examples of mounting with flex interfaceTroubleshooting If your drive is not working properly, these troubleshooting tips may help solve the problem. 1. Does the drive spin up? A spinning drive produces a faint whine and clicking noise. If your drive does not spin, check that the drive is securely inserted. 2. Does the computer recognize the drive? Verify that the drive is enabled in the system CMOS or setup program. If not, select the auto detect option and enable it. If your drive has a problem, it may not be recognized by the system. If the operating system does not recognize the drive, you need to load your host adapter drivers. 3. Does ScanDisk find the drive defect-free? ScanDisk is a utility located on your Windows startup diskette that scans the drive for defects. If defects are detected, this may be an indication of a problem. 4. Why does my computer hang on startup? Verify that your system is ATA compatible. You need either an ATA-compatible motherboard connector or ATA host adapter to use this drive. © 2005 Seagate Technology LLC. All rights reserved Publication number: 100375653, Rev. A, May 2005, Printed in USA Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC. SeaTools is a registered trademark or trademark of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or specifications.