Craftsman | 315.177520 | Operator`s manual | Craftsman 315.177520 Operator`s manual

Operator's Manual
II:RRFTSMRN'I
6 VOLT CORDLESS
HAND VAC
Model No.
315.177520
Important
Information:
• Charge batteries before first use
• Use only charger provided
• Always use hand vac with filter installed
Save this manual for
future reference
CAUTION:
• Safety
• Features
Read and follow all
Safety Rules and Operating Instructions
before first use of this product.
Customer
Help Line: 1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly
Rd., Hoffman
visit the Craftsman web page: www.sears.com/craftsman
983000-190
2-03
• Operation
• Maintenance
• Parts List
Estates,
IL 60179
USA
•
Warranty .........................................................................................................................................................................
2
•
Introduction .....................................................................................................................................................................
2
•
General Safety Rules .....................................................................................................................................................
3
•
Specific Safety Rules .................................................................................................................................................
•
Symbols ..........................................................................................................................................................................
6
•
Features .........................................................................................................................................................................
7
•
Operation ....................................................................................................................................................................
•
Maintenance .............................................................................................................................................................
•
Exploded View and Repair Parts List ...........................................................................................................................
11
•
Customer Service Information ......................................................................................................................................
12
FULL ONE YEAR WARRANTY
ON rRRFTSMRN
3-5
8-9
9-10
CORDLESS HAND VAC
If this rRRFTSMRN Cordless Hand Vac fails to give complete satisfaction within one year from the date of purchase,
RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES, and Sears
will replace it, free of charge.
If this rRRFI"$MRN Cordless Hand Vac is used for commercial or rental purposes, this warranty applies for only 90 days
from the date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817 WA, Hoffman
Estates, IL 60179
Your cordless hand vac has many features for making the
use of this product more pleasant and enjoyable. Safety,
performance, and dependability have been given top
priority in the design of this product making it easy to
maintain and operate.
_i,
Look for this symbol to point
Your safety is involved.
_k
WARNING:
,_
out important
safety
WARNING:
Do not attempt to use this product until
you thoroughly read and completely understand the
operator's manual. Pay close attention to the safety
rules, including Dangers, Warnings, and Cautions. If
you use this product properly and only as intended,
you will enjoy years of safe, reliable service.
precautions.
It means
attention!!!
The operation of any tool can result in foreign objects being thrown into your eyes, which can result in
O
side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over
eyeglasses
or standard
safetybeginning
glasses operation,
with side shields.
wear goggles
eye protection
which
is marked
severe eye damage.
Before
always Always
wear safety
or safety
glasses
with to
comply with ANSI 7'87.1.
2
A
TOOLUSE
WARNING:
Read and understand all
instructions. Failure to follow all instructions listed
below, may result in electric shock, fire and/or
•
Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
•
Store idle tools out of the reach of children and
other untrained persons. Tools are dangerous in the
hands of untrained users.
serious personal injury.
SAVE THESEINSTRUCTIONS
WORKAREA
•
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp
cutting edges are less likely to bind and are easier to
control.
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids or gases. Power tools may create sparks
which may ignite the dust or fumes..
ELECTRICAL
•
•
•
Check for misalignment or binding of moving
parts, breakage of parts, and any other condition
that may affect the tool's operation. If damaged,
have the tool serviced before using. Many accidents
are caused by poorly maintained tools.
•
Use only accessories that are recommended by
the manufacturer for your model. Accessories that
may be suitable for one tool, may become hazardous
when used on another tool.
SAFETY
Don't expose power tools to rain. Water entering a
power tool will increase the risk of electric shock or malfunction.
PERSONAL
SAFETY
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious
personal injury.
•
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts and exhaust.
Loose clothes, jewelry, or Iong hair can be caught in
moving parts.
•
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables
better control of the tool in unexpected situations. Do
not use on a ladder or unstable support.
•
Use safety equipment. Always wear eye protection.
Dust mask must be used for appropriate conditions.
AND CARE
SERVICE
•
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of electric shock or injury.
Hold tool by insulated gripping surfaces when performing an operation where the tool may contact hidden
wiring or its cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
ADDITIONAL
•
RULES
FOR SAFE OPERATION
Do not allow children to operate Hand Vac or play
with Hand Vac as a toy. Close attention is necessary
when used near children.
•
This Hand Vac is intended for household use ONLY.
•
Use this Hand Vac ONLY for its intended use as
described in this manual. Use only the attachments
recommended in this manual.
3
•
If Hand Vac is not working properly, has been
dropped, damaged, left outdoors, or dropped into
water, return to your nearest Sears Service Center.
•
Do not abuse cord. Never carry charger or base by
the cord or yank to disconnect from electrical outlet.
Grasp charger, not the cord, and pull to unplug. Do not
allow cord to hang over edge of table or counter or to
touch hot surfaces.
•
Donot handlechargeror HandVacwith wet
•
Hand Vac is for dry pick up only.
•
Do not put any objects in ventilation openings. Do not
use with any opening blocked: keep openings free of
dust, lint, hair, and anything that may reduce air flow.
•
NEVER vacuum materials such as hot coals, cigarette
butts, matches, etc.
•
Do not use without filter in place.
•
Turn off all controls before unplugging from or
plugging into an electrical outlet for charging.
•
Use extra care when using on stairs.
•
Do not use to pick up hard objects such as nails,
screws, coins, etc. Damage or injury could result.
•
Hand Vac does not have to be plugged into an electrical outlet, therefore it is always in operating condition.
Be aware of possible hazards when using your Hand
Vac or when changing accessories.
USE ONLY THE CHARGER PROVIDED WITH YOUR
HAND VAC. Do not substitute any other charger. Use
of another charger could cause batteries to explode
causing possible serious injury.
DO NOT PLACE HAND VAC OR BATTERIES NEAR
FIRE OR HEAT. They may explode.
•
•
hands.
of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized
service center. Following this rule will reduce the risk
of shock, fire, or serious injury.
Make sure your extension cord Is in good condition. When using an extension cord, be sure to use
one heavy enough to carry the current your product will draw. A wire gage size (A.W.G.) of at least
16 is recommended for an extension cord 100 feet
or less in length. A cord exceeding 100 feet is not
recommended. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier
the cord. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
•
Drugs, alcohol, medication. Do not operate tool
while under the influence of drugs, alcohol, or any
medication. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also.
SERVICE
•
Your Hand vac should be charged in a location where
the temperature is more than 50°F but less than 100°F.
•
•
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with skin, wash at least 10 minutes then seek immediate medical attention.
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
•
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to
this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
•
•
A
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the risk
of serious personal injury.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
WARNING: ELECTRIC SHOCK COULD OCCUR IF
CHARGED OUTDOORS OR ON WET SURFACES.
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment of moving parts, binding
SAVE THESE INSTRUCTIONS
4
•
A damaged battery is subject to explosion. To avoid
serious personal injury, properly dispose of a
damaged battery.
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet) 25'
50'
100'
•
Save these instructions. This manual contains
important safety and operating instructions for
charger item no. 9 11050 (981496-001). Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
Cord Size (AWG)
16
16
•
•
Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
To reduce risk of injury, charge only nickelcadmium and nickel metal hydride type rechargeable batteries. Other types of batteries may burst
causing personal injury and damage. Following this
rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
To reduce risk of damage to charger body and
cord, pull by charger plug rather than cord when
disconnecting charger. Following this rule will
reduce the risk of serious personal injury.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress. Following this rule will reduce
the risk of serious personal injury.
An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
16
Note: AWG = American Wire Gage
•
Do not operate charger with a damaged cord or
plug. If damaged, have replaced immediately by a
qualified serviceman. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
•
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of
electric shock or fire. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
To reduce the risk of electric shock, unplug
charger from outlet before attempting any maintenance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
DANGER: RISK OF ELECTRIC SHOCK. DO NOT
TOUCH UNINSULATED PORTION OF OUTPUT
CONNECTOR OR UNINSULATED BATTERY
TERMINAL.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. if you loan someone this tool, loan them
these instructions also. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
SAVE THESE INSTRUCTIONS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.
Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
HZ
Hertz
Frequency (cycles per second)
W
Watt
Power
Minutes
Time
Alternating Current
Type or a characteristic
of current
Direct Current
Type or a characteristic
of current
No Load Speed
Rotational speed, at no load
Per Minute
Revolutions, reciprocations, strokes,
surface speed, orbits, etc. per minute
Safety Alert
Precautions that involve your safety
Wet Conditions Alert
Do not expose to rain or use in damp
min
•_
no
/min
,_
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
measures.
SYMBOL
MEANING
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or
serious injury.
i_
WARNING: Indicates a potenUally hazardous
situation, which, ifnot avoided, could result in serious injury,
A
CAUTION: indicates a potentially hazardous situation, which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices that may cause property damage.
Important: Advises you of important information or instructions vital to the operation or maintenance of
the equipment.
Note: Advises you of additional information concerning the operation or maintenance of the equipment.
KNOW
YOUR HAND VAC
Note: Accessories can be purchased at your nearest
Sears Retail Store.
See Figure 1.
SWITCH
Before attempting to use your hand vac, familiarize
yourself with all operating features and safety
requirements.
Your hand vac is equipped with an ON/OFF switch located
on the top of your hand vac.
• i, WARNING:
Carefully read through this entire
operator's manual before using your new hand vac.
Pay close attention to the Rules For Safe Operation,
Warnings and Cautions. If you use your hand vac
properly and only for what it is intended, you will enjoy
years of safe, reliable service.
&
PRODUCT
Your hand vac has been shipped completely assembled.
Inspect it carefully to make sure no breakage or damage
has occurred during shipping. If any parts are damaged or
missing, contact your nearest Sears Retail Store to obtain
replacement parts before attempting to operate hand vac.
Packaging includes hand vac unit with batteries concealed
in the unit, dust bowl, charger, and this operator's manual.
_i,
WARNING: Do not allow familiarity with your hand
vac to make you careless. Remember that a careless
fraction of a second is sufficient to inflict severe injury.
SPECIFICATIONS:
Motor
6.0 Volt DC
Switch
On/Off
CHARGER
Charger Rating
Item No. 9_11050 (981496-001)
120V, 6OHz, AC only
Charger Voltage
Charger Rate
6 Volt
3-6 Hours
WARNING: If any parts are missing, do not operate
your hand vac until the missing parts are replaced.
Failure to do so could result in possible serious
personal injury.
SWITCH(0N-OFF)
DUSTBOWL
FILTER
HANDVAC
CHARGER
Fig. 1
7
,_
Note: This situation only occurs when continuous use of
your hand vac causes the batteries to become hot. It does
not occur under normal circumstances. Refer to "CHARGING BATTERIES" for normal recharging of batteries. If
the charger does not charge your batteries under normal
circumstances, return the charger to your nearest Sears
Repair Center for electrical check.
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
CHARGING
BATTERIES
The batteries for this tool are concealed in the hand vac
and have been shipped in a low charge condition to
prevent possible problems. Therefore, you should charge
them overnight prior to use.
RED LIGHT
(LED)
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (vacuuming followed by
recharging) for them to become fully charged.
REDLIGHT(LED)
TO CHARGE
•
Charge batteries only with the charger provided.
•
Make sure power supply is normal house voltage,
120 volts, 60 Hz, AC only.
•
Connect charger to hand vac by inserting charger plug
into input jack. As shown in Figure 2, input jack is
located on the back side of the tool. See Figure 2..
•
Connect charger to power supply.
•
The charge indicator light (LED), located on the back
side of the tool, will light up and glow when the charger
is properly connected to the power supply. This light
indicates the charger is operating properly. It will remain
on until the charger is disconnected from the power
supply. The light only glows while your tool is charging,
not during use.
•
INPUTJACK
CHARGER
HANDMAC
After normal usage, 3 to 6 hours is required to recharge
batteries. Note: If batteries are completely discharged,
6 hours or longer of charging time is required to fully
recharge batteries,
•
The battery will become slightly warm to the touch while
charging. This is normal and does not indicate a problem.
•
Do not operate the tool while it is connected to the
charger. The vacuuming ability will not increase.
•
Do not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
•
When batteries become fully charged, unplug charger
from power supply and disconnect it from tool.
IMPORTANT
INFORMATION
HOT BATTERIES
INPUT
JACK
Fig. 2
SWITCH
See Figure 3.
Your hand vac is equipped with an ON/OFF switch
located on top of hand vac. As shown in the arrows in
Figure 3, to turn your hand vac ON, push switch forward.
To turn it OFF, pull switch back.
SWITCH
TO TURN
ON
TOTURN
OFF
FOR RECHARGING
When using your hand vac continuously, the batteries in
your tool will become hot.You should let a hot battery cool
down for approximately 30 minutes before attempting to
recharge.
Fig. 3
8
CLEANING
YOUR
HAND
MAC
See Figures 4, 5, and 6.
_k
•
Shake or lightly brush any dust or dirt off filter.
•
Empty dust bowl and wash if necessary. Make sure
dust bowl is completely dry before reattaching to hand
vac.
WARNING:
Never use your hand vac without the
filter properly in place.
TO REMOVE
The dust bowl should be checked, emptied and cleaned
periodically to obtain maximum dust collection.
TO REMOVE
•
DUST
FILTER
HANDVAC
BOWL
Depress dust bowl release button located on top of
hand vac then pull bowl down and out as shown in
Figure 4.
DUSTBOWL
DEPRESSDUSTBOWL
RELEASEBUTTON
TO INSTALL
Fig. 5
TO REPLACE
•
TO
iN TsTTOALL_
HANDVAC
FILTER
Place the filter in the dust bowl in the direction shown
in Figure 5.
TO REATTACH
DUST BOWL
See Figure 6.
REMO_II_III_
•
Position the two sections as shown in Figure 6. Align
slots on bottom of dust bowl with tabs on bottom of
motor housing then snap the two sections together.
DUSTBOWL
DUSTBOWL
TO REMOVE
•
_k
AND CLEAN
Fig. 4
FILTER
Remove the filter by simply pulling it out of the dust
bowl. See Figure 5.
SLOTS
Fig. 6
Do not abuse power tools. Abusive practices can damage
tool as well as workpiece.
WARNING:
When servicing, use only identical
Craftsman replacement parts. Use of any other
part may create a hazard or cause product damage.
Only the parts shown on parts list, page 11, are intended
to be repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
_k
TABS
_k
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken or destroy
plastic.
WARNING:
Do not attempt to modify this tool or
create accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
9
BATTERIES
•
The batteries for your hand vac are nickel-cadmium
rechargeable batteries. Length of service from each
charging will depend on the type of work you are doing.
Store and charge your batteries in a cool area.
Temperatures above or below normal room
temperature will shorten battery life.
•
Never store batteries in a discharged condition.
Recharge them immediately after they are
discharged.
•
All batteries gradually lose their charge. The higher
the temperature the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
The batteries in this tool have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventually wear out. Do not disassemble your hand
vac and attempt to replace the batteries. Handling of
these batteries, especially when wearing rings and
jewelry, could result in a serious burn.
To obtain the longest possible battery life, we suggest the
following:
To preserve natural resources, please
recycle or dispose of batteries properly.
BATTERY PACK
FOR RECYCLING
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickel-cadmium
batteries in ordinary trash.
_L
Consult your local waste authority for information
regarding available recycling and/or disposal options.
10
REMOVAL
AND PREPARATION
WARNING:
Upon removal, cover the battery pack's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
CRAFTSMAN
I
6 VOLT CORDLESS
MODEL HO. 315.177520
HAND
VAC
The model number will be found on a plate att;:ched to the motor housing, Always mention the model
number in all correspondence regarding your CORDLESS HAND VAC or when ordering repair pads.
SEE BACK
PAGE
FOR PA,:ITS ORDERING
INSTRUCTIONS
1
PA :TS LIST
Key
No.
Part
Number
Description
Qty.
1
*Item No. _911408
Filter (3: 04015) .................................................
2
2
*Item No. _911050
C,_ _ rge_ 981496-001
1
983000-190
Ope;ato,'s
* Can Be Purchased
) .......................................
Manual
Thru =_SOS (Retail Special Order System)
11
I
Your
Home
For repair-in
your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
Calmanytime,
®
(1-800-469-4663)
day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime,
day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655
(U.S.A.)
Para pedir servlclo de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
1-800-361-6665
Au Canada pour service en franc;a_s:
1-800-LE-FOYER
s_
Trademark /
Mc
(1-800-533-6937)
WWW sears.ca
(1-888-784-6427)
® Registered Trademark /
(Canada)
Service Mark of Sears, Roebuck and Co
® Marca Reg=strada / TMMarca de Fabnca / su Marca de Servlc=O de Sears
Mc Marque de commerce / MD Marque cleposee de Sears, Roebuck and Co
Roebuck
and Co
@ Sears,
Roebuck
and Co
Download PDF