Monte Carlo Fan Company 3BvR52XXd-L Installation manual

Monte Carlo Fan Company 3BvR52XXd-L Installation manual
Owner’s Guide and Installation Manual
5HS52XXD-L/5HS52XXS-L Series Fan
UL Model No. : 52-ANT
Attach sales receipt to this card and retain as your proof of purchase
DATE OF PURCHASE:
RETAILER NAME:
MODEL NUMBER:
RETAILER ADDRESS:
To register your fixture, please visit our website www.montecarlofans.com
7.7kgs
17.0 lbs
Total fan weight with light kit
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING
READ AND SAVE THESE INSTRUCTIONS
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com
© 2013 Monte Carlo Fan Company
2
6/25/2013
2
3
Before you begin installing the fan, Switch
power off at Service panel and lock service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Before installing this fan make sure the outlet box is
properly installed to the house structure. To reduce
the risk of fire, electric shock, or personal injury,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)
Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet box is securley fastened by at least two points to a structural ceiling member ( a loose box will cause the fan to
wabble). Use only the screws provided with
the outlet box.
4
5
6
1
Canopy disk
Downrod
Cross Pin
Yoke
Keeper
Pin
Canopy
Tread leadwires and safety cable first
through the canopy disk, Canopy and
lastly downrod.
Loosen the 2 set screws in
yoke for downrod to slip into yoke. Insert downrod into yoke on top of the Fan Body. Align the
hole in the Downrod with the hole in the Yoke.
Insert the Pin through the Yoke and Downrod
until the point appears on the other side. Install
the Keeper Pin
7
8
Safety cable installation
Tighten the 2 Set screws on the Yoke
once the downrod is in place. Check
motor for shipping stabilizers and remove if present.
9
Safety Cable
Lag Screw
safety
cable
washer
3” lag
screw
Hang assembled fan from the mounting bracket installed to ceiling in previous step. Make sure the fan
is hanging straight. Rotate fan until the tab on the
Mounting bracket engages the slot on the Downrod
Ball. This must be done to prevent the fan body from
rotating when the blades are in motion.
© 2013 Monte Carlo Fan Company
lock
washer
For Canadian installation and for USA fan and light
kit combinations over 35 lbs, in both flush and
downrod modes the safety cable must be installed
into the house structure beams using 3” lag
screws, washers and lock washers provided. Make
sure that when the safety cable is fully extended
the lead wires are longer than the cable and no
stress is placed on the lead wires.
Note:If Installing The Secondary Support Safety
Cable in the U.S., Do Not Remove Knockouts In
The Outlet Box.
3
Make sure the studs protruding from the
bottom of the Mounting bracket are installed with threads all the way through
the bracket.
6/25/2013
10
12
11
House
Black
Fan
Blue
Black
White
White
Ground
Green
Connect black and blue wire from fan to Black or (Hot)
wire from house. Connect White wire from Fan to White
(Neutral) wire from house. Connect Ground leads from
mounting bracket and downrod to Ground lead from
house. Refer to Safety Tips section of manual.
13
Cover Ring
Make wire connections to power source using wire nuts
provided. Make sure that no filiments are outside of
the wirenut. After making the wire connections, the
wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one
side of the outlet box and ungrounded conductor on the
other side of the outlet box.
Lift Conopy allowing the 2 studs to
protrude through the canopy.
14
15
Flush Mount Installation
Go to Step 26
Next lift the cover ring and install knurled
nuts as shown. Tighten the knurled nuts
securely. The canopy should adjust for
any irregularity in the ceiling or Outlet
box.
16
Remove every other screw as circled
and save for later use.
17
18
“L” shape
slots
Install rubber pad between fan
body and canopy.
© 2013 Monte Carlo Fan Company
Remove side covers from canopy exposing
4 holes. 2 closed holes and 2 open “L”
shape holes.
4
Pass leadwires and safety cable through
the canopy.
6/25/2013
19
21
20
Hands free hook
Place canopy over fan body aligning holes.
Replace the 3 screws removed and
tighten securely. Check motor for
shipping stabilizers and remove if
present.
Remove the all thread studs from the
lower part of the mounting bracket. Hang
fan from mounting bracket by the
hands free hook into a closed hole on
the edge of the Canopy. Note: For
Canadian mounting refer to Step #8.
22
23
24
Fan
House
Blue
Black
Black
White
White
Ground
Green
Take 4 screws from hardware pack
and insert 2 one on each side of
bracket to match the L slot screw
holes in canopy. Keep 2 screws for
later use.
Connect black and blue wire from fan to Black or (Hot)
wire from house. Connect White wire from Fan to White
(Neutral) wire from house. Connect Ground leads from
mounting bracket and downrod to Ground lead from
house. Refer to Safety Tips section of manual.
25
26
Lift fan to mounting bracket, aligning the “L”
shape holes with the screws on the mounting
bracket. Turn the fan clockwise to lock in
position. Install the other 2 screws included
in hardware bag and tighten all 4 securely.
Place blade holders onto blades aligning holes
in blade holder with holes in blade. Make sure
that the side of the blade you select is facing
downward. Install 3 screws and fiber washers
to back side of blade as shown. Tighten
screws securely. Repeat this process 4 more
times until all blades are assembled.
© 2013 Monte Carlo Fan Company
Make wire connections to power source using wire nuts
provided. Make sure that no filiments are outside of
the wirenut. After making the wire connections, the
wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one
side of the outlet box and ungrounded conductor on the
other side of the outlet box.
27
5
Install blades to motor using the 10 motor
screws provided. Tighten screws securely.
6/25/2013
28
29
30
Remove nut and save for next step.
Remove switch cap housing from fan.
Remove the plug of fitter. Install
switch cap housing to light kit by
turning clockwise to tighten.
Install keeper nut over lead wires.
31
32
33
Tighten keeper nut onto threaded
pipe from the light kit.
Install 3 x 60 watt Candelabra base
bulbs. WARNING: Over lamping the
fan will result in the fan lights shutting down until the proper wattage
of bulbs are installed.
Reset the lights by turning off the wall
switch, breaker,or by remote. Replace
bulbs with the correct wattage bulbs,
turn the power on.
Locate blue and white wire from the fan
marked “For light kit”. Connect blue from fan
to black from light and white from fan to white
from light by pushing connectors together.
34
35
36
Attach switch cap to fan by lining up
2 slot ear holes and 1 screw hole and
twisting cap. Then tighten the 3
screws.
Remove finial nut, finial cap, hex nut,
and washer from fitter.
Install rubber washer and nut to
glass tighten nut.
© 2013 Monte Carlo Fan Company
6
6/25/2013
37
Install finial cap and finial nut to
glass and tighten finial nut.
© 2013 Monte Carlo Fan Company
7
6/25/2013
TROUBLe SHOOTING
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or
wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please
check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our Customer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Suggested Remedy
Trouble
1. If fan does not start:
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate
when switch is in the middle.
4.Make sure that shipping stabilizer tabs have been removed from motor (see installation
step #13).
2. If fan sounds noisy:
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware are finger tight. Check to be sure light bulb is tight in socket and not touching glass
shade(s). If vibration persists from glass, remove glass and install a 1/4" wide rubber band
on glass neck to act as an insulator. Replace glass and tighten screws against rubber band.
5.Some fan motors are sensitive to signals from Solid State variable speed controls. DO
NOT USE a Solid State variable speed control.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear
after this period.
3. If fan wobbles:
1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the
notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box
and junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the blades. Measure this distance from
blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measurement. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer (not
supplied) between the blade and blade holder at the screw closest to the motor. To adjust a
blade tip up, insert washer (not supplied) between the blade and blade holder at the two
screws farthest from the motor. Reverse the position of the washer if blades mount from top
of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation.
4. If light does not work:
1.Check
2.Check
3.Check
4.Check
blue wire from fan to make sure it is connected to hot wire from house.
for loose or disconnected wires in fan switch housing.
for loose or disconnected wires in light kit.
for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing.
WARNING: Over lamping the fan will result in the fan lights shutting down until the
proper wattage of bulbs are installed.
Reset the lights by turning off the wall switch, breaker,or by remote. Replace bulbs with the
correct wattage bulbs, turn the power on.
© 2013 Monte Carlo Fan Company
8
6/25/2013
Dec.2011 New formate
Jan.2012 Update customer service phone number
Jun.2013 Update for CUL regulation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement