68U instruction book
Instruction Book
Specification of USB Digital
Microscope
Product name:digital microscope
P/N:VC68U-200HD
Approved by:
Version :
Checked by :
department :
Settled by:
Ver 1.0
Product Engieen
date: 2010-01-15
Instruction Book
●Introduction
In order to describe product specifications, usually expressed by a set of
documents.
As part of it, This technical specification book provides the camera
module's technical specifications,to have limitation towards this type of
goods,is the guidance documents of the product quality inspection.
The microscope is made up of high-quality IC and electronic
components,with
clear
image
quality,
low
power
consumption,
high-resolution,applies to small objects to be larger,photo and video
production,is the best choice of small objects recoganization.
This specification is inconsistent with the type of when the sample size,
to the provisions of this specification book as a benchmark specifications
and samples are usually co-exist. If the goods are objections, the parties
can refer to specifications and sample consultation.
Document and the information contained are the confidential information,
protected by contract or by law shall not be leaked. Content only limited
by the scope of the designated recipient or special purposes.
Unauthorized have no right to read and use.
●Functional Description and use
 Build in Mono Digital Microphone,support audio recording.
 Toggle
switch
off,control
environmental Protection
the
using
time,
energy-saving,
Instruction Book
 Manual adjust LED,image effects can be the best
 UVC standard,free drive
 LED fill light,can be used in dark enviorment
 Camera button will record the image anywhere
 Apply 2 million pixels CMOS sensitive chip, clarity imagy
 Manual focus, 60 to 200 times magnification, can see the small
anti-counterfeiting bank notes in 100 RMB .
 Double-focus make higher magnification,can see the pores of the skin
clearly
 Metal bracket,to prevent the moving of the lens,easier for checking
 Transparent
shield
to
protect
the
lens
against
the
dust
pollution,improve the life of the product!
 USB2.0 high speed transmission interface,connect to the laptops and
desktops anytime and anywhere
 Simple digital dial
 Support instant messaging software:MSN,QQ,Skype etc.
 Support Windows XP,Vista,Win-7
Digital microscope camera has 1 million times amplification,the products
widely used in microelectronics industrial inspection, quality inspection,
scientific research and teaching, the areas of medical examination. is the
best helper of the production of industrial plants, research institutes,
schools and education, image recognition unit.
Instruction Book
●Technical parameters
Additional
Built-in microphone
feature
Image sensor
Image pixel
Image format
Data format
Definition
shot
Focus range
Angle of view
Frame rate
Camera control
White balance
Exposure
Sleep current
Work current
Save temperature
Work
temperature
Drivers standard
compatible
systems
1/3-inch CMOS Sensor
1600V x 1200H
160x120,176x144,320x240,352x288,640x480,
1280v1024、1600×1200
YUY2
Centre:520 line,Square:400 line
F= 15.8
5mm -∞
<15  (V)
26-30frames/[email protected],15-30 frames/[email protected]
Saturation, contrast, sharpness
Automatic, manual
Automatic, manual ( 2600-5000K ) average
brightness
<1 mA
<180 mA
-20C to +60C
10C to +40C
WDM driver WIA Drivers TWAIN Drivers
1、
2、
3、
4、
windows 2000 Professional
windows XP Professional Service Pack 1
windows XP Professional Service Pack 2
windows Vista
Cold start the
windows XP Professional Service Pack 2
computer
Hot start the
windows XP Professional Service Pack 2
computer
Interface
[email protected]
Instruction Book
Gray scale
Level 8
Support display
LCD,CRT monitor
mode
Net weight
camera:100g stand:135g
dimension
125MM×28MM×4.4MM
● Start Microscope
Connect your Microscope to your PC USB port, start the software by
clicking the
icon generated on the desktop after installation and
you will see the following screen pop up.
1. When the Microscope is disconnected from your PC USB port,
the screen will display “No Device detected, please connect your
Microscope directly to your PC USB port.”
Instruction Book
● Change preview size
You can change the preview size by the following operation:
Note: The size of the photo taken is equivalent to the preview size
selected in the Options menu/Preview Size.
● Rotate the output image angle
You can rotate the output image clockwise and counter-clockwise.
Instruction Book
● Date/Time
You can display or turn off Date/Time by the following operation:
● Language
You can choose On Screen Display language by the following
operation:
Instruction Book
● Skin
You can choose to change the appearance of your MicroCapture
screen by the following operation:
● Full screen
1. You can enter & quit full screen mode by:
1) Double-clicking the preview area.
2) Clicking the full screen icon:
Instruction Book
3) Choose Full screen mode from menu.
When in full screen mode, click on the Full screen icon to turn off
and restore toolbars and menus.
● Capture
1. Photo capture
You can take photos by either of the following ways:
1) Click the camera button
2) Choose Capture and then click Photo
Instruction Book
3) By pressing F11
Captured photos are saved automatically and image thumbnails will
be available on the right side of the MicroCapture screen for further
editing. For editing photo, please refer to later operations.
2. Video capture
You can record video by either of the following two ways:
1) Click the video camera button
2) Choose from the menu bar Capture and then click Video
When recording, there is a red dot flashing on the video camera
button.
Instruction Book
Video is saved in AVI format.
Stop capture:
1) Click the flashing video camera button
2) Choose Capture and then click Stop capturing
Note: Please note the best pixels for video capturing is 640x480.
● Edit photos
1. Preview photos
1) Clicking on an image thumbnail will display the image selected on
the preview area, with its size displayed on the left-bottom corner
2) You can double click the image thumbnail and an independent
preview box will pop up as shown below:
Instruction Book
2. Save photos
You can save photo by right clicking on the thumbnail and then
choose Save.
Instruction Book
The file can be saved in either jpeg or bmp. The jpeg size in which the
photo is saved is the maximum allowed for jpeg. You can choose to
decrease the size by adjusting quality. Click the Advanced button to
view and select jpeg save options.
3. Delete photos
By right clicking and then choosing Delete, you can delete the
selected photo
Or, at the independent preview box you can choose delete icon to
delete the previewed photo.
4. Copy photos
Right click on the thumbnail and then choose Copy.
Instruction Book
How to use measurement & calibration function
1 Point the microscope onto a target object e.g. a ruler; rotate the focus
wheel to get a clear focus.
2 When the focus at the clearest point, take a snapshot
3 Watch the calibration at the lower-end of the focus wheel; note down
the magnification value that corresponds to the indicator marker on the
microscope body as shown below. That value is the magnification at
which the focus was set and the image taken. (This is very important,
since only with the magnification ratio noted down can the object size be
worked out at later steps!!)
4 Open the captured photo double clicking on the thumbnail. A preview
window will open
Instruction Book
5 Input the magnification ratio noted down into the box indicated at the
top right corner of the preview window. (Please note it is necessary to
input the magnification ratio noted down on step3; otherwise the
measurement is meaningless.)
6 Now you can measure the size of the whole or part of the object you
have taken using the available options. Click on the icons on top of
the window. Following are the options:
1) Direct line: click
left-click mouse to choose a start point and drag
mouse to an end point, Notice that the measurement is displayed.
Release the mouse when done.
2) Multi-line: click
,left-click mouse to choose a start point and drag
to an end point. Notice that the measurements are displayed as you go
along. Release mouse when done. You can continue measuring from the
previous end point to a next point and so on.
3) Circle-radius: click
,left-click to choose a start point for a circle;
draw the circle to an end point, release the mouse, and the radius of
Instruction Book
the circle will be displayed.
4) Circle-diameter: click
, left-clicking to choose a start point for a
circle; draw the circle to an end point, release the mouse, and the
radius of the circle will be displayed.
5) Angle: click
, left-click to choose a start point for an angle, draw
the line to another point and then release the mouse to create one line
for an angle. Move your mouse to bring out another line of the angle,
left-click when the angle is ok. The angle value will then display.
6) Unit: click
, you can choose the unit at which the measured
values display. Units available include: pixels / inches / km / mt / mm /
Instruction Book
cm / micro
7 Other operations you can carry out on the photo taken include:
1) :
make notes on the photo taken
2) :
select font, font style, font size etc
3) :
draw line, box etc on the photo
4) :
line color
5) :
line thickness
6) :
line type
7) :
undo operation
Note:
1. The magnification ratio you are allowed to input is from 20 to 200. Do
not input any value beyond that.
2. The measurement value worked out by the software is only for
reference; it may not be 100% correct.
3. The measurement function is only available on Windows Operating
System.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement