Makita HR3200C Instruction manual

Makita HR3200C Instruction manual
ENGLISH
INSTRUCTION MANUAL
Rotary Hammer
HR3200C
HR3210C
HR3210FCT
008536
DOUBLE INSULATION
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
1
ENGLISH
SPECIFICATIONS
Model
Concrete
HR3200C
HR3210C
Tungsten-carbide tipped bit
32 mm
Core bit
90 mm
Capacities
Steel
13 mm
Wood
32 mm
No load speed (min-1)
315 - 630
Blows per minute
1,650 - 3,300
Overall length
398 mm
Net weight
4.4 kg
Safety class
HR3210FCT
424 mm
4.8 kg
5.0 kg
/II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
END201-4
For Model HR3200C
ENG102-1
Symbols
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-6:
Sound pressure level (LpA) : 89 dB(A)
Sound power level (LWA) : 100 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
・ Read instruction manual.
・
DOUBLE INSULATION
・
Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic
equipment
and
its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an
environmentally
compatible
recycling facility.
ENG215-1
Vibration
The vibration total value (tri-axial vector
determined according to EN60745-2-6:
Work mode : chiseling function
Vibration emission (ah,CHeq) : 12.5 m/s2
Uncertainty (K) : 1.5 m/s2
sum)
ENG303-1
Work mode : hammer drilling into concrete, 16 mm
diameter and 100 mm depth
Vibration emission (ah,HD) : 18 m/s2
Uncertainty (K) : 1.5 m/s2
ENE044-1
Intended use
The tool is intended for hammer drilling in brick, concrete
and stone as well as for chiselling work.
ENG302-1
Work mode : drilling into metal
Vibration emission (ah,D) : 2.5 m/s2 or less
ENF002-1
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
For Model HR3210C
ENG102-1
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-6:
Sound pressure level (LpA) : 89 dB(A)
Sound power level (LWA) : 100 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
2
ENG215-1
Vibration
The vibration total value (tri-axial vector
determined according to EN60745-2-6:
Work mode : chiseling function
Vibration emission (ah,CHeq) : 7.5 m/s2
Uncertainty (K) : 1.5 m/s2
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
sum)
GEA005-1
ENG303-1
Work mode : hammer drilling into concrete, 16 mm
diameter and 100 mm depth
Vibration emission (ah,HD) : 10 m/s2
Uncertainty (K) : 1.5 m/s2
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
ENG302-1
Work mode : drilling into metal
Vibration emission (ah,D) : 2.5 m/s2 or less
Save all warnings and
instructions for future reference.
For Model HR3210FCT
ENG102-1
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-6:
Sound pressure level (LpA) : 88 dB(A)
Sound power level (LWA) : 99 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical Safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal Safety
ENG215-1
Vibration
The vibration total value (tri-axial vector
determined according to EN60745-2-6:
Work mode : chiseling function
Vibration emission (ah,CHeq) : 8 m/s2
Uncertainty (K) : 1.5 m/s2
sum)
ENG303-1
Work mode : hammer drilling into concrete, 16 mm
diameter and 100 mm depth
Vibration emission (ah,HD) : 10 m/s2
Uncertainty (K) : 1.5 m/s2
ENG302-1
Work mode : drilling into metal
Vibration emission (ah,D) : 2.5 m/s2 or less
ENH101-8
EC-DECLARATION OF CONFORMITY
Model; HR3200C,HR3210C,HR3210FCT
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN60745, EN55014, EN61000 in accordance with
Council Directives, 2004/108/EC, 98/37/EC.
CE2007
000230
Tomoyasu Kato
Director
Responsible Manufacturer:
3
21.
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
SERVICE
24. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
25. Follow instruction for lubricating and
changing accessories.
26. Keep handles dry, clean and free from oil and
grease.
10.
Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. . Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
16. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
GEB007-2
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to rotary hammer safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious
personal injury.
1.
Wear ear protectors. Exposure to noise can
cause hearing loss.
2.
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3.
Hold power tools by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock
the operator.
4.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun
glasses are NOT safety glasses. It is also
highly recommended that you wear a dust
mask and thickly padded gloves.
5.
Be sure the bit is secured in place before
operation.
6.
Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
7.
In cold weather or when the tool has not been
4
8.
9.
10.
11.
12.
13.
14.
Lighting up the lamps
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
Hold the tool firmly with both hands.
Keep hands away from moving parts.
Do not leave the tool running. Operate the tool
only when hand-held.
Do not point the tool at any one in the area
when operating. The bit could fly out and
injure someone seriously.
Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
For Model HR3210FCT
1. Lamp
1
008549
CAUTION:
Do not look in the light or see the source of light
directly.
To turn on the lamp, pull the trigger. Release the trigger
to turn it off.
•
NOTE:
•
Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it may
lower the illumination.
SAVE THESE INSTRUCTIONS.
Speed change
WARNING:
1. Adjusting dial
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
FUNCTIONAL DESCRIPTION
•
1
CAUTION:
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on
the tool.
008538
The revolutions and blows per minute can be adjusted
just by turning the adjusting dial. The dial is marked 1
(lowest speed) to 5 (full speed).
Refer to the table below for the relationship between the
number settings on the adjusting dial and the
revolutions/blows per minute.
Switch action
1. Switch trigger
1
Number on
adjusting dial
Revolutions per
minute
Blows per minute
5
4
3
2
1
630
590
480
370
315
3,300
3,100
2,500
1,900
1,650
008537
CAUTION:
Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
008550
•
•
5
CAUTION:
If the tool is operated continuously at low speeds
for a long time, the motor will get overloaded,
resulting in tool malfunction.
Selecting the action mode
The speed adjusting dial can be turned only as far
as 5 and back to 1. Do not force it past 5 or 1, or
the speed adjusting function may no longer work.
•
Rotation with hammering
Changing the quick change chuck for
SDS-plus
1
For Model HR3210FCT
The quick change chuck for SDS-plus can be easily
exchanged for the quick change drill chuck.
Removing the quick change chuck for SDS-plus
1
2
2
1
1. Lock button
2. Pointer
3. Change lever
2
3
1. Quick change
chuck for
SDS-plus
2. Change cover
3. Chuck cover
008540
For drilling in concrete, masonry, etc., depress the lock
button and rotate the change lever so that the pointer
points to the
symbol. Use a tungsten-carbide tipped
bit.
Rotation only
3
008608
2
CAUTION:
Before removing the quick change chuck for
SDS-plus always remove the bit.
Hold the change cover with the thumb and the middle
finger and pull it in the direction arrow 1. With the
change cover pulled in that direction, hold the chuck
cover with the index finger. While holding the chuck
cover so, pull out the quick change chuck for SDS-plus
in the direction of arrow 2 at a stroke.
Attaching the quick change drill chuck
3
•
1
1. Lock button
2. Change lever
3. Pointer
1
008600
For drilling in wood, metal or plastic materials, depress
the lock button and rotate the change lever so that the
pointer points to the symbol. Use a twist drill bit or
wood bit.
Hammering only
1. Spindle
2. Quick change
drill chuck
3. Change cover
1. Pointer
2. Change lever
3. Lock button
1
3
2
008552
2
Grasp the change cover and place the quick change drill
chuck on the spindle of the tool.
Make sure that the quick change drill chuck is secured
by trying to pull it several times.
3
008539
For chipping, scaling or demolition operations, depress
the lock button and rotate the change lever so that the
pointer points to the symbol. Use a bull point, cold
chisel, scaling chisel, etc.
•
•
6
CAUTION:
Do not rotate the change lever when the tool is
running under load. The tool will be damaged.
To avoid rapid wear on the mode change
mechanism, be sure that the change lever is
always positively located in one of the three
action mode positions.
CAUTION:
Always use the side grip to ensure operating safety
when drilling in concrete, masonry, etc.
The side grip swings around to either side, allowing easy
handling of the tool in any position. Loosen the side grip
by turning it counterclockwise, swing it to the desired
position and then tighten it by turning clockwise.
Torque limiter
•
The torque limiter will actuate when a certain torque
level is reached. The motor will disengage from the
output shaft. When this happens, the bit will stop turning.
•
CAUTION:
As soon as the torque limiter actuates, switch off
the tool immediately. This will help prevent
premature wear of the tool.
Installing or removing the bit
Indicator lamp
1
1. Power-ON
indicator lamp
(green)
2. Service indicator
lamp (red)
1
2
1. Bit shank
2. Bit grease
003150
Clean the bit shank and apply bit grease before installing
the bit.
Insert the bit into the tool. Turn the bit and push it in until
it engages.
008541
The green power-ON indicator lamp lights up when the
tool is plugged. If the indicator lamp does not light up,
the mains cord or the controller may be defective. The
indicator lamp is lit but the tool does not start even if the
tool is switched on, the carbon brushes may be worn out,
or the controller, the motor or the ON/OFF switch may be
defective.
The red service indicator lamp lights up when the carbon
brushes are nearly worn out to indicate that the tool
needs servicing. After approx. 8 hours of use, the motor
will automatically be shut off.
1. Bit
2. Chuck cover
1
2
008543
ASSEMBLY
•
2
If the bit cannot be pushed in, remove the bit. Pull the
chuck cover down a couple of times. Then insert the bit
again. Turn the bit and push it in until it engages.
After installing, always make sure that the bit is securely
held in place by trying to pull it out.
To remove the bit, pull the chuck cover down all the way
and pull the bit out.
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
Side grip
1
1
1. Side grip
2
008544
008542
7
1. Bit
2. Chuck cover
Bit angle (when chipping, scaling or
demolishing)
Use the dust cup to prevent dust from falling over the
tool and on yourself when performing overhead drilling
operations. Attach the dust cup to the bit as shown in the
figure. The size of bits which the dust cup can be
attached to is as follows.
1. Change lever
2. Lock button
3. Pointer
1
2
Bit diameter
6 mm - 14.5 mm
12 mm - 16 mm
Dust cup 5
Dust cup 9
006406
3
OPERATION
008545
Hammer drilling operation
The bit can be secured at 24 different angles. To change
the bit angle, depress the lock button and rotate the
change lever so that the pointer points to the symbol.
Turn the bit to the desired angle.
Depress the lock button and rotate the change lever so
that the pointer points to the symbol. Then make sure
that the bit is securely held in place by turning it slightly.
Depth gauge
1
008547
1. Depth gauge
2. Clamp screw
2
Set the change lever to the symbol.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light
pressure gives best results. Keep the tool in position and
prevent it from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at
an idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
008546
The depth gauge is convenient for drilling holes of
uniform depth. Loosen the clamp screw and adjust the
depth gauge to the desired depth. After adjusting,
tighten the clamp screw firmly.
•
NOTE:
•
The depth gauge cannot be used at the position
where the depth gauge strikes against the gear
housing/motor housing.
Dust cup
CAUTION:
When the bit begins to break through concrete or if
the bit strikes reinforcing rods embedded in
concrete, the tool may react dangerously. Maintain
good balance and safe footing while holding the
tool firmly with both hands to prevent dangerous
reaction.
Blow-out bulb (optional accessory)
1. Dust cup
1. Blow-out bulb
1
1
001300
002449
8
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
For Model HR3200C,HR3210C
Use the optional drill chuck assembly. When installing it,
refer to "Installing or removing the bit" described on the
previous page.
Set the change lever so that the pointer points to
the symbol.
For Model HR3210FCT
Use the quick change drill chuck as standard equipment.
When installing it, refer to "changing the quick change
chuck for SDS-plus " described on the previous page.
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as
it will go. Hold the ring firmly and turn the sleeve
clockwise to tighten the chuck. To remove the bit, hold
the ring and turn the sleeve counterclockwise.
Set the change lever to the
symbol.
You can drill up to 13 mm diameter in metal and up to 32
mm diameter in wood.
Chipping/Scaling/Demolition
008548
Set the change lever to the symbol.
Hold the tool firmly with both hands. Turn the tool on and
apply slight pressure on the tool so that the tool will not
bounce around, uncontrolled. Pressing very hard on the
tool will not increase the efficiency.
Drilling in wood or metal
•
1. Chuck adapter
2. Keyless drill
chuck
1
•
2
•
008551
1. Spindle
2. Quick change
drill chuck
3. Change cover
1
•
CAUTION:
Never use "rotation with hammering" when the
quick change drill chuck is installed on the tool.
The quick change drill chuck may be damaged.
Pressing excessively on the tool will not speed up
the drilling. In fact, this excessive pressure will only
serve to damage the tip of your bit, decrease the
tool performance and shorten the service life of the
tool.
There is a tremendous twisting force exerted on
the tool/bit at the time of hole breakthrough. Hold
the tool firmly and exert care when the bit begins to
break through the workpiece.
Always secure small workpieces in a vise or similar
hold-down device.
Diamond core drilling
When performing diamond core drilling operations,
always set the change lever to the
position to use
"rotation only" action.
3
2
008552
•
1
1. Sleeve
2. Ring
CAUTION:
If performing diamond core drilling operations
using "rotation with hammering" action, the
diamond core bit may be damaged.
MAINTENANCE
2
•
008553
9
CAUTION:
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
Lubrication
1. Screws
CAUTION:
•
This servicing should be performed by Makita
Authorized or Factory Service Centers only.
This tool requires no hourly or daily lubrication because
it has a grease-packed lubrication system. Lubricate the
tool every time the carbon brushes are replaced.
Run the tool for several minutes to warm it up. Switch off
and unplug the tool.
1
008603
1. Screws
Align the change lever with the symbol , loosen the
five screws and then remove the crank cap.
1
1
008601
Loosen the four screws and remove the handle. Note
that the top screws are different from other screws.
008604
1. Connector
•
CAUTION:
Always remove the crank cap only after aligning
the change lever with the symbol . Never remove
it forcibly without aligning the change lever with the
symbol
. Failure to do so does not allow
reassembling.
1
008607
Disconnect the connector by pulling them.
2
1. Crank cap cover
2. Screws
1
008605
Rest the tool on the table with the bit end pointing
upwards. This will allow the old grease to collect inside
the crank housing.
Wipe out the old grease inside and replace with a fresh
grease (30 g). Use only Makita genuine hammer grease
(optional accessory). Filling with more than the specified
amount of grease (approx. 30 g) can cause faulty
hammering action or tool failure. Fill only with the
specified amount of grease.
008602
Loosen the two screws on crank cap cover and
remove the crank cap cover.
•
10
CAUTION:
Be careful not to damage the connector or lead
wires especially when wiping out the old grease.
ACCESSORIES
To reassemble the tool, follow the disassembling
procedure in reverse.
•
CAUTION:
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
SDS-Plus Carbide-tipped bits
•
Bull point
•
Core bit
•
Cold chisel
•
Diamond core bit
•
Hammer grease
•
Scaling chisel
•
Grooving chisel
•
Drill chuck assembly
•
Drill chuck S13
•
Chuck adapter
•
Chuck key S13
•
Bit grease
•
Side grip
•
Depth gauge
•
Blow-out bulb
•
Dust cup
•
Safety goggles
•
Plastic carrying case
CAUTION:
Do not tighten the crank cap excessively. It is made
of resin and is subject to breakage.
•
1. Connector
1
008606
Connect the connector firmly and then reinstall the
handle.
CAUTION:
Be careful not to damage the connector or lead
wires especially when installing the handle.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
•
11
Makita Corporation Anjo, Aichi, Japan
884769-228
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement