Advantech FPM-5151G Series User manual

Advantech FPM-5151G Series User manual
用户手册
FPM-5151G/5171G/
5191G Series
15" XGA/17" SXGA/19" SXGA
Industrial Monitor with Resistive
Touchscreen, Direct-VGA, DVI
Ports and DC12-30V Inputs
Copyright
The documentation and the software included with this product are copyrighted 2012
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
This manual includes the following products:
FPM-5151G Series
FPM-5171G Series
FPM-5191G Series
Part No. 200K51X100
Edition 1
Printed in China
December 2012
FPM-5151G/5171G/5191G Series User Manual
ii
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
iii
FPM-5151G/5171G/5191G Series User Manual
Declaration of Conformity
This device complies with part 15 of the FCC rules: Operation is subject to the following two condition:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Technical Support and Assistance
1.
2.
Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
FPM-5151G/5171G/5191G Series User Manual
iv
Safety Instructions
1.
2.
3.
Read these safety instructions carefully.
Keep this User Manual for later reference.
Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
 The power cord or plug is damaged.
 Liquid has penetrated into the equipment.
 The equipment has been exposed to moisture.
 The equipment does not work well, or you cannot get it to work according to the
user's manual.
 The equipment has been dropped and damaged.
 The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. The sound pressure level at the operator's position according to IEC 704-1:1982
is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.
v
FPM-5151G/5171G/5191G Series User Manual
FPM-5151G/5171G/5191G Series User Manual
vi
Contents
Chapter
1
General Information ............................1
1.1
1.2
Introduction ............................................................................................... 2
Specifications ............................................................................................ 2
1.2.1 General ......................................................................................... 2
1.2.2 Touchscreen (Optional) ................................................................ 2
LCD Specification...................................................................................... 3
Connectors................................................................................................ 3
Dimensions ............................................................................................... 4
Figure 1.1 FPM-5151G Dimensions ............................................ 4
Figure 1.2 FPM-5171G Dimensions ............................................ 5
Figure 1.3 FPM-5191G Dimensions ............................................ 6
1.3
1.4
1.5
Chapter
2
Mounting ..............................................7
2.1
Mounting the Monitor ................................................................................ 8
2.1.1 Wall Mounting (Optional) .............................................................. 8
Figure 2.1 Wall Mounting............................................................. 8
2.1.2 Panel Mounting ............................................................................. 9
Figure 2.2 Panel Mounting........................................................... 9
Figure 2.3 Panel Mounting........................................................... 9
2.1.3 Rack Mounting (Optional) ........................................................... 10
Figure 2.4 FPM-5151 Rack Mounting........................................ 10
Figure 2.5 FPM-5171 Rack Mounting........................................ 11
Figure 2.6 FPM-5191 Rack Mounting........................................ 11
2.1.4 Desktop, Swing-ARM Mounting .................................................. 12
Figure 2.7 Desktop Stand .......................................................... 12
Figure 2.8 Swing Arm ................................................................ 13
Appendix A
Touchscreen ......................................15
A.1
A.2
A.3
Introduction ............................................................................................. 16
Touchscreen Specifications .................................................................... 16
A.2.1 Electrical Specifications .............................................................. 16
A.2.2 Environment Specifications......................................................... 16
Installing Driver for Windows OS ............................................................ 16
Appendix B
OSD Operation Keypad .....................17
B.1
OSD Board Overview.............................................................................. 18
B.1.1 OSD Button Description.............................................................. 18
Table B.1: OSD Button Description ........................................... 18
B.1.2 LED Function .............................................................................. 19
Table B.2: LED Function............................................................ 19
OSD Key Functions................................................................................. 19
B.2.1 Menu Start .................................................................................. 19
B.2.2 Input Source Select..................................................................... 20
B.2.3 Contrast/Brightness Setting ........................................................ 21
B.2.4 Geometry Menu – For DVI Input................................................. 22
B.2.5 Color Temperature Menu............................................................ 23
B.2.6 Language Menu .......................................................................... 24
B.2.7 OSD Manager ............................................................................. 25
B.2
vii
FPM-5151G/5171G/5191G Series User Manual
B.2.8
B.2.9
B.2.10
B.2.11
B.2.12
Auto Configuration Menu ............................................................ 26
Mode Information Menu.............................................................. 27
Memory Recall Menu.................................................................. 28
Exit Menu.................................................................................... 29
Hot Keys ..................................................................................... 30
FPM-5151G/5171G/5191G Series User Manual
viii
Chapter
1
1
General Information
Sections include:
 Introduction
 Specifications
 LCD Specification
 Power Consumption
 Connectors
 Dimensions
1.1 Introduction
Advantech's FPM-5151G/5171G/5191G is a 15"/17”/19” color TFT LCD flat panel
monitor built specifically for industrial applications. With the optional touchscreen,
FPM-5151G/5171G/5191G is an excellent and user-friendly system control interface.
In addition to its usual application as an LED panel monitor,FPM-5151G/5171G/
5191G comes standard with direct VGA and DVI control signal inputs, making it
compatible with Industrial PCs and Workstations. Its OSD (On Screen Display)
function allows you to adjust display factors such as brightness, contrast, colors and
VGA signal information. Functions that are more and more critical as HMI users
become aware of the benefits of flat panel monitors. The whole chassis is of stainless
steel, and the front panel is of aluminum with NEMA4/IP65 compliance.
FPM-5151G/5171G/5191G also comes in a touch screen version (FPM-5151G-R/
FPM-5171G-R/FPM-5191G-R). With an 5-wire resistive type touchscreen, this
monitor can be immediately transformed into a remote control system. The
Advantech FPM-5151G/5171G/5191G is the ultimate HMI solution for your industrial
application.
1.2 Specifications
1.2.1 General
FPM-5151
Construction
FPM-5171
FPM-5191
Heavy-duty aluminum and steel chassis
Front panel Aluminum, NEMA4 / IP65 Compliant
Control
OSD (On Screen Display) control pad on rear
Mounting
Panel, wall, desktop, VESA ARM or rack (with rackmount)
Dimensions 449.92 x 315.63 x 50.5 mm 481.9 x 355.9 x 55 mm
(18.97”x 14.01”x 2.17”)
(W x H x D) (17.71”x 12.43”x 2”)
481.93 x 384.6 x 59 mm
(18.97”x 15.14”x 2.32”)
Weight
10 kg (22.04 lbs)
6 kg (13.22 lbs)
8 kg (17.63 lbs)
1.2.2 Touchscreen (Optional)
FPM-5151
Type
5 wire, analog resistive
Resolution
2048*2048
Controller
USB & RS-232 interface
FPM-5171
FPM-5191
Power Consump- +5 V @ 200 mA
tion
Life Span
100 million activation (typical) at a single point with a 5/8"
diameter silicone finger with a 350 g load at 2 touches per second
FPM-5151G/5171G/5191G Series User Manual
2
FPM-5171
FPM-5191
Display Type
XGA TFT (LED)
SXGA TFT (LED)
SXGA TFT (LED)
Display Size
15”
17”
19”
Max. Colors
16.2M
16.7M
16.7M
Max. Resolution
1024 x 768
1280 x 1024
1280 x 1024
View Angle (H/V°)
160/140
170/160
170/160
Luminance
400 cd/m2
350 cd/m2
350 cd/m2
Storage Temperature
-40 ~ 85°C
-30 ~ 85°C
-20 ~ 60°C
Operating Temperature
0 ~ 50°C
0 ~ 50°C
0 ~ 50°C
Contrast Ratio
700:1
1000:1
1000:1
Lamp Life Time(MTBF)
50,000 hrs.
50,000 hrs.
50,000 hrs.
1.4 Connectors
The following connectors are situated on the left hand side of the FPM-5151G/
5171G/5191G series:
 VGA Port (DB-15)
This DB-15 connector can be connected to the system via the external 15-pin
DB-15 connector located on the left side of the system unit.
 DVI Port (DVI-D)
Connected with a standard DVI connector thru I/O port of this unit. Only supports digital signals
 Touchscreen Connector (DB-9) (optional)
This connector will be present only if a touchscreen is installed. It must be connected to the RS-232 port of the PC. The touchscreen cable is included with all
orders which include the touchscreen option.
 Touchscreen Connector (USB) (Optional)
This connector will be present only if a touchscreen is installed. It must be connected to the USB port of the PC. The touchscreen cable is included with all
orders which include the USB touchscreen option.
Note!

RS-232 & USB touchscreen interface does not allow connection into the
system at the same time, but it can be changed via switch.
Plug-In Block 3P Male (ME050-50803) DC12-30V
This block connector can be connected via the external plug-in block 3P with
flanges Female MC211-F103 connector
3
FPM-5151G/5171G/5191G Series User Manual
General Information
FPM-5151
Chapter 1
1.3 LCD Specification
1.5 Dimensions
3DQHO&XWRXW'LPHQVLRQ[PP[
Figure 1.1 FPM-5151G Dimensions
FPM-5151G/5171G/5191G Series User Manual
4
Chapter 1
3DQHO&XWRXW'LPHQVLRQ[PP[
FPM-5151G/5171G/5191G Series User Manual
5
General Information
Figure 1.2 FPM-5171G Dimensions
3DQHO&XWRXW'LPHQVLRQ[PP[
Figure 1.3 FPM-5191G Dimensions
FPM-5151G/5171G/5191G Series User Manual
6
Chapter
2
Mounting




Wall Mounting
Panel Mounting
Rack Mounting
Desktop Mounting
 Swing Arm Mounting
2
2.1 Mounting the Monitor
The FPM-5151G/5171G/5191G Series can be mounted in many different ways. The
versatility of the FPM-5151G/5171G/5191G mounts enable it to be mounted on your
desk or anywhere else.
2.1.1 Wall Mounting (Optional)
FPM-5151G/5171G/5191G can be mounted directly on a wall with panel mounting
brackets. Customers must order the stand kit for FPM-5151G/5171G/5191G. Please
refer to Figure 2.1 and follow the following steps to mount FPM-5151G/5171G/5191G
on a wall:
Note!
The below rack mounting kit can be used for desktop mounting, refer to
section 2.1.4.1 for detail information.)
Part No. of FPM-5151G’s optional rack
mounting kit:
FPM-5151G-SMKE
(can be used for FPM-5171G)
FPM-5171G-SMKE
(can be used for FPM-5151G)
FPM-5191G-SMKE( FPM-5191G only)
Part No. of FPM-5171G’s optional rack
mounting kit:
Part No. of FPM-5191G’s optional rack
mounting kit:
1.
2.
3.
Screw the hook and desk-stand brackets on the wall.
Attach 4 screws around the bracket
Put the Industrial monitor into the screws around the bracket
Figure 2.1 Wall Mounting
FPM-5151G/5171G/5191G Series User Manual
8
FPM-5151G/5171G/5191G can be mounted directly on a panel with additional
mounting brackets. Please refer to Figure 2.2 and follow the following steps:
Note!
Fix 10pcs panel bracket around the industrial monitor, refer to the below figure.
Fix into the panel by screwing the bracket.
Figure 2.2 Panel Mounting
Figure 2.3 Panel Mounting
9
FPM-5151G/5171G/5191G Series User Manual
Mounting
1.
2.
You can use the materials provided in the accessory box for panel
mounting!
Chapter 2
2.1.2 Panel Mounting
2.1.3 Rack Mounting (Optional)
If you need to install the FPM-5151G/5171G/5191G on a rack, you must order the
rack mounting kit for FPM-5151G/5171G/5191G. Attach the rack mounting brackets
on FPM-5151G/5171G/5191G with the screws, then affix the monitor in the rack.
Refer to Figure 2.3 for FPM-5151G’s rack mounting.
Refer to Figure 2.4 for FPM-5171G’s rack mounting.
Refer to Figure 2.5 for FPM-5191G’s rack mounting.
Note:
Part No. of FPM-5151G’s optional rack
mounting kit:
Part No. of FPM-5171G’s optional rack
mounting kit:
Part No. of FPM-5191G’s optional rack
mounting kit:
IPPC-6152A-RMKE (FPM-5151G only)
IPPC-6172A-RMKE (FPM-5171G only)
IPPC-6192A-RMKE (FPM-5191G only)
Figure 2.4 FPM-5151 Rack Mounting
FPM-5151G/5171G/5191G Series User Manual
10
Chapter 2
Mounting
Figure 2.5 FPM-5171 Rack Mounting
Figure 2.6 FPM-5191 Rack Mounting
11
FPM-5151G/5171G/5191G Series User Manual
2.1.4 Desktop, Swing-ARM Mounting
The FPM-5151G/5171G/5191G Series can be mounted in other ways, such as
desktop and swing-arm.
2.1.4.1 Desktop Stand
FPM-5151G/5171G/5191G can be mounted as stand in the desk directly by a
additional mounting brackets. Customers must order the stand kit for FPM-5151G/
5171G/5191G. Please refer to figure 2.6 and follow these steps:
Note (The below optional mounting kit can also be used for wall mounting, refer to
section 2.1.4.1 for detail information.)
Part No. of FPM-5151G’s optional rack
mounting kit:
FPM-5151G-SMKE
(can be used for FPM-5171G)
FPM-5171G-SMKE
(can be used for FPM-5151G)
FPM-5191G-SMKE
( FPM-5191G only)
Part No. of FPM-5171G’s optional rack
mounting kit:
Part No. of FPM-5191G’s optional rack
mounting kit:
Figure 2.7 Desktop Stand
FPM-5151G/5171G/5191G Series User Manual
12
Chapter 2
2.1.4.2 Swing Arm (VESA Compliant)
FPM-5151G/5171G/5191G has been designed with support for the VESA Arm standard. Refer to figure 2.7. Supports both 75mm and 100mm VESA dimension.
Mounting
Figure 2.8 Swing Arm
13
FPM-5151G/5171G/5191G Series User Manual
FPM-5151G/5171G/5191G Series User Manual
14
Appendix
A
Touchscreen
A
A.1 Introduction
The FPM-5151G/5171G/5191G Series optional touchscreen uses advanced 5-wire
resistive technology. It provides more accurate sensing capacity than other
technologies. The touchscreen is specially designed for tough industrial
environments, and has been approved to FCC Class A standards.
Note!
RS-232 & USB touchscreen interface does not allow connection to the
system at the same time. It can be changed by switch.
A.2 Touchscreen Specifications
A.2.1 Electrical Specifications


Operating Voltage: 5.5V or less
Capacitance:100nF(maximum)
A.2.2 Environment Specifications



Operating Temperature: -10 ~ + 60°C
Storage Temperature: -40 ~ +80°C
Humidity: if 40° C, humidity <80% RH
if 40° C, humidity < 90% RH No dew condensation
A.3 Installing Driver for Windows OS
The touchscreen has drivers for Win 2000/2003/XP/CE/Vista/Win7/Linux/MS-DOS.
You should read the instructions in CD-ROM Disk Touchscreen section carefully
before you attempt installation. The FPM-5151G/5171G/5191G-R series need to
install Penmount 6000 driver. Please find Penmount 6000 folder and install the driver
into your system.
Note!
The driver manual are examples only. You must follow the flow chart
instructions and pay attention to the instructions which then appear on
your screen.
Note!
The USB & RS-232 cable not allow to connect to system at the same
time.
Note!
USB & RS-232 interface driver is different, uninstall previous driver
before installing a different driver.
Note!
If there is any others OS driver need, could download at the web site:
http://www.penmount.com.tw (Penmount 6000)
FPM-5151G/5171G/5191G Series User Manual
16
Appendix
B
OSD Operation
Keypad
B
B.1 OSD Board Overview
The OSD keypad, including six keys and a two color indicator, is designed as the
OSD operation interface.
B.1.1 OSD Button Description
Table B.1: OSD Button Description
Power
Turn the monitor power ON or OFF.
Auto/Exit
Automatically adjust the clock, phase, H-position and
V-position.
Exit menu.
Down/Right/Increase
Increase the brightness.
Move the selector to the next option.
Increase the gauge value of the selected option.
Up/Left/Decrease
Decrease the brightness.
Move the selector to the previous option.
Decrease the gauge value of the selected option.
Menu/Sel
Activate the OSD menu.
Enter/confirm the selected option.
Source
Changes Input video source
FPM-5151G/5171G/5191G Series User Manual
18
Table B.2: LED Function
ON
Green
StandBy/OFF
Green Blinking
No Signals
Orange
B.2 OSD Key Functions
Each selected value is stored into LCD memory after SEL signal input or time out.
The stored values are not affected if the power is turned off. But the selected value is
not available in case a selected mode is changed before time out or power is turned
off before time out. TIME OUT -> 5-6 seconds ( Can be set in OSD Manager) The
default definition of input keys is shown as following:
B.2.1 Menu Start
Generate Main Menu
Press MENU Button in OSD function key
 Main Menu -- DISPLAY IN SCREEN



Sub-Menu – DISPLAY IN SCREEN
N/A
Available Key Functions
Turn off (turn off backlight)
·Move the selector to the left
·Select the sub-menu
Select to exit the menu
or wait for time-out
·Confirm
·Enter the selected option.
·Move the selector to
the right
·Select the sub-menu
N/A
19
FPM-5151G/5171G/5191G Series User Manual
Appendix B OSD Operation Keypad
B.1.2 LED Function
B.2.2 Input Source Select

Generate Main Menu
Select
by Left and Right Button, and then press Menu Button for selection
confirmation.
 Main Menu -- DISPLAY IN SCREEN

Sub-Menu – DISPLAY IN SCREEN

Available Key Functions
Power Off the
LCD Monitor
Select to move up/down
Return to the previous
menu
Select to confirm
Select to move up/down
N/A
FPM-5151G/5171G/5191G Series User Manual
20

Generate Main Menu
Select
by Left and Right Button, and then press Menu Button for selection
confirmation.

Main Menu -- DISPLAY IN SCREEN

Sub-Menu – DISPLAY IN SCREEN

Available Key Functions
Power Off the LCD Monitor
·Select to move up/down
·Decrease the gauge value
of the selected option
Return to the previous
menu
Select to confirm
·Select to move up/
down
·Increase the gauge
value of the selected
option
N/A
21
FPM-5151G/5171G/5191G Series User Manual
Appendix B OSD Operation Keypad
B.2.3 Contrast/Brightness Setting
B.2.4 Geometry Menu – For DVI Input

Generate Main Menu
Select
by Left and Right Button,press Menu Button for selection confirmation.

Main Menu -- DISPLAY IN SCREEN

Sub-Menu – DISPLAY IN SCREEN

Available Key Functions
Power Off the LCD Monitor
·Select to move up/down
·Decrease the gauge value
of the selected option
Return to the previous
menu
Select to confirm
·Select to move up/
down
·Increase the gauge
value of the selected
option
N/A
FPM-5151G/5171G/5191G Series User Manual
22

Generate Main Menu
Select
by Left and Right Button, and then press Menu Button for selection
confirmation.

Main Menu -- DISPLAY IN SCREEN

Sub-Menu – DISPLAY IN SCREEN

Available Key Functions
Power Off the LCD Monitor
·Select to move up/down
·Decrease the gauge value
of the selected option
Return to the previous
menu
Select to confirm
·Select to move up/
down
·Increase the gauge
value of the selected
option
N/A
23
FPM-5151G/5171G/5191G Series User Manual
Appendix B OSD Operation Keypad
B.2.5 Color Temperature Menu
B.2.6 Language Menu

Generate Main Menu
Select
by Left and Right Button, and then press Menu Button for selection
confirmation.

Main Menu -- DISPLAY IN SCREEN

Sub-Menu – DISPLAY IN SCREEN

Available Key Functions
Power Off the LCD Monitor
Move the selector to the left
Return to the previous
menu
Select to confirm
Move the selector to the
right
N/A
FPM-5151G/5171G/5191G Series User Manual
24

Generate Main Menu
Select
by Left and Right Button, and then press Menu Button for selection
confirmation.

Main Menu -- DISPLAY IN SCREEN

Sub-Menu – DISPLAY IN SCREEN

Available Key Functions
Power Off the LCD Monitor
·Select to move up/down
·Decrease the gauge value
of the selected option
Return to the previous
menu
Select to confirm
·Select to move up/
down
·Increase the gauge
value of the selected
option
N/A
25
FPM-5151G/5171G/5191G Series User Manual
Appendix B OSD Operation Keypad
B.2.7 OSD Manager
B.2.8 Auto Configuration Menu

Generate Main Menu
Select
by Left and Right Button, and then press Menu Button for selection
confirmation.

Main Menu -- DISPLAY IN SCREEN

Sub-Menu – DISPLAY IN SCREEN

Available Key Functions
Power Off the LCD Monitor
N/A
Return to the previous
menu
Select to confirm
N/A
N/A
FPM-5151G/5171G/5191G Series User Manual
26

Generate Main Menu
Select
by Left and Right Button, and then press Menu Button for selection
confirmation.

Main Menu -- DISPLAY IN SCREEN

Sub-Menu – DISPLAY IN SCREEN

Available Key Functions
Power Off the LCD Monitor
Move the selector to the left
Return to the previous
menu
Select to confirm
Move the selector to the
right
N/A
27
FPM-5151G/5171G/5191G Series User Manual
Appendix B OSD Operation Keypad
B.2.9 Mode Information Menu
B.2.10Memory Recall Menu

Generate Main Menu
Select by Left and Right Button,
, and then press Menu Button for selection
confirmation.

Main Menu -- DISPLAY IN SCREEN

Sub-Menu – DISPLAY IN SCREEN

Available Key Functions
N/A
N/A
N/A
Select to confirm
N/A
N/A
FPM-5151G/5171G/5191G Series User Manual
28

Generate Main Menu
Select
by Left and Right Button, and then press Menu Button for selection
confirmation.

Main Menu -- DISPLAY IN SCREEN

Sub-Menu – DISPLAY IN SCREEN
29
FPM-5151G/5171G/5191G Series User Manual
Appendix B OSD Operation Keypad
B.2.11 Exit Menu
B.2.12Hot Keys
OSD LOCK/UNLOCK
HOT KEYS
Press
first, and then press
for change this setting, Followed this
sequence for the button press so that you can have OSD LOCK and UNLOCK setting

Enter OSD LOCK MODE
– Press HOT KEY, the screen will show this action first
– Don’t remove HOT KEY until the screen indicated this task is finished.

Enter OSD UNLOCK MODE
– Press HOT KEY, the screen will show this action first
– Don’t remove the HOT KEY until the screen indicated this task is finished.
FPM-5151G/5171G/5191G Series User Manual
30
Appendix B OSD Operation Keypad
31
FPM-5151G/5171G/5191G Series User Manual
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement