Vax CCW-502 Specifications

Vax CCW-502 Specifications
REFRIGERANT
RECOVERY/EVACUATION
SYSTEM from
TM
INSIDE
TM
US patents: 4,523,897; 5,209,653,
other US and foreign patents pending.
TM
USERÕS OPERATING MANUAL
ADVANCED TEST PRODUCTS, INC. • Miramar, FL
Telephone: (954) 499-5400 • Fax: (954) 499-5454 • Toll Free: (800) 327-5060
www.ProVaxAC.com
TABLE OF CONTENTS
INTRODUCTION
IMPORTANT SAFETY INFORMATION and OPERATING GUIDELINES
CARE AND MAINTENANCE OF YOUR ProVaxTM
ADDITIONAL RECOVERY TANK INFORMATION
PURGING NON-CONDENSABLE GASES
HELPFUL HINTS FOR REFRIGERANT RECOVERY & EVACUATION
OPERATING YOUR ProVaxTM
SELF PURGING YOUR ProVaxTM
PULLING A VACUUM
DIAGRAM FOR REFRIGERANT RECOVERY & EVACUATION
DIAGRAM FOR "PUSH/PULL" METHOD
SET-UP DIAGRAM FOR TANK PRE OR SUB COOLING PROCEDURE
OPTIONAL RECOVERY / TANK PRE OR SUB COOLING FOR FIXED
HOSE SET-UP
VACUUM PUMP MAINTENANCE / OIL CHANGE
ProVax PARTS DIAGRAM/PARTS AND ACCESSORIES LIST
ProVax WIRING DIAGRAM
INSTALLATION OF OPTIONAL 80% TANK CAPACITY SENSING KIT
TROUBLESHOOTING YOUR PROVAXTM
SPECIFICATIONS
WARRANTY INFORMATION
ENVIROMENTAL PROTECTION AGENCY (EPA) INSTRUCTIONS
EPA REGIONALOFFICES
1
2
3-4
5
6
7
8-9
10-11
12
12
12-13
13
13
14
15
16-17
18
19
20-21
22
23
24
25
INTRODUCTION
Congratulations on your purchase of the ProVax™ refrigeration recovery/evacuation system. Using an innovative new design (patents pending), Promax™ has created a unique recovery system. The ProVax™ combines
both a recovery unit and a vacuum pump into one unit, conveniently eliminating the need to carry both to the
job site.
A Robinair Cooltech® 6 CFM vacuum pump, using a two-stage, offset rotary vane design, provides a powerful high vacuum capability and assures moisture removal, while its high pumping capacity reduces evacuation
time. US patents: 4,523,897; 5,209,653, other US and foreign patents pending.
The ProVax™ provides everything you need to recover and evacuate a system, all in one package.
2
m IMPORTANT SAFETY & OPERATING
GUIDLINE INFORMATION m
PERSONAL SAFETY
TANK SIZE
30 lb. Tank
50 lb. Tank
mSAFETY COMES FIRST! Read all safety, operating
guidelines and instructions before operating your
ProVaxTM.
MAX NET WEIGHT
24 lbs.
40 lbs.
TABLE 1: Representative Sample, R-22
CAUTION: ONLY A QUALIFIED TECHNICIAN
SHOULD OPERATE THIS RECOVERY UNIT.
The operator must be familiar with air conditioning
and refrigeration systems, refrigerants and the dangers of pressurized components.
Note: Promax strongly recommends the use of
the ADS-100 Refrigerant Scale for monitoring
tank capacity.
Your ProVax has two Internal Pressure Shut
Off switches, a standard 400psi and a 550psi
(when the High Pressure [R410A] switch is
engaged). The shut off switches will automatically
reset after the pressure drops below 200 psi.
Always think before acting, familiarity breeds
carelessness and carelessness can be harmful to
your health, or worse, result in death.
m WARNING: The Internal Pressure Shut Off
Switches do not prevent tank overfill. If your system
shuts off on high pressure and is connected to your
tank, you may have overfilled your tank and created
a very dangerous situation! Take immediate measures to relieve any high pressure and/or tank overfill.
mWARNING: Always wear safety goggles and
protective gloves when working with refrigerants.
Contact with refrigerant may cause injury.
Disconnect hoses with extreme caution! All hoses
may contain liquid refrigerant under pressure.
Read all safety information regarding the safe
handling of refrigerant and refrigerant oil, including the
Material Safety Data Sheet. MSDS sheets can be
obtained from your refrigerant supplier.
When recovering large amounts of liquid, use the
"Push/Pull method (see diagram on page 13).
Be sure that any room where you are working is thoroughly ventilated, especially if a leak is suspected.
Refrigerant vapor is hazardous to your health and can
cause death.
m CAUTION: When using the "Push/Pull"
method, once the "Push/Pull" siphon is started, it
can continue and overfill the storage tank even if
the tank is equipped with a "shut off" float sensor.
The siphon can continue even after the machine
is turned off.You must manually close the valves on
the tank and the unit to prevent overfilling of the
recovery tank.
mAvoid breathing A/C refrigerant and lubrication
vapor or mist. Exposure may irritate eyes,nose and
throat. If accidental system discharge occurs, ventilate
work area before resuming service.
To reduce the risk of injury, care should be taken when
moving this equipment.
Always operate the unit on a flat level surface.
Promax strongly recommends the use of the optional
80% Capacity Shutoff Kit (p/n KT-5002).
When installed and used with a recovery tank that
has an internal float switch, the ProVax will shut
down automatically when the tank is 80% full.
Your ProVax is pre-wired from the factory for this kit.
If the tank pressure exceeds 300 psi, use the tank
cooling procedure to reduce the tank pressure.
(See Pages 13 & 14)
m A scale must be used to avoid overfilling the
storage tank. DO NOT OVERFILL. Tank is full at
80% volume. Tank may explode if filled more
than 80% due to liquid expansion. Table 1 is a
representative sample for R-22 refrigerant:
3
m IMPORTANT SAFETY & OPERATING
GUIDLINE INFORMATION m
ELECTRICAL SAFETY
CONT-
Always open service and cylinder valves slowly.
This allows rapid control of the flow of gases if
there is any danger. Once it is determined that
there is no danger, the valves can be opened
fully.
When using an extension cord it should be a 3-wire, 14
AWG minimum and no longer than 25 feet.
cWARNING! Whenever you perform any type
of maintenance work on your ProVax, insure
that it is disconnected from the power supply
before you begin.
Always isolate large amounts of refrigerant and
close off valves after use, so if a leak should
develop anywhere in the system, the refrigerant
will not escape.
FIRE SAFETY
i WARNING: TO REDUCE THE RISKOF FIRE:
Keep all connections to the refrigeration system
thoroughly dry and clean. If moisture enters the
refrigeration system, it is likely to cause considerable damage.
Never operate unit in an explosive environment!
Do not use this equipment in the vicinity of spilled or
open containers of gasoline or any other flammable
liquid.
cWARNING!
Use this equipment in locations with mechanical ventilation that provides at least four air changes per hour
or locate the equipment at least 18 inches above the
floor.
Pressurized tank contains liquid refrigerant.
Never overfill storage tanks. Overfilling of the tank
may cause a violent explosion and possible injury
or death. Do not exceed the working pressure of
Recovery Tank cylinder.
Never use oxygen when testing for leaks.
Any oil in contact with oxygen under pressure will form
an explosive mixture.
REFRIGERANT SAFETY
ProVax is approved for use with the following
category III, IV and V refrigerants (Per ARI 740):
R-12, R-22, R-134A, R-401A, R-401B, R-401C,
R-402A, R-402-B, R-404A, R-406A, R-407A,
R-407-B, R-407C, R-407D, R-408A, R-409A,
R-410A, R-411A, R-411B, R-412A, R-500, R-502,
R-507 and R-509
4
CARE AND MAINTENANCE OF YOUR ProVaxTM
Use of a filter/dryer at the inlet is mandatory.
A filter/dryer must always be used between the
recovery machine and the inlet hose.We recommend
that a clean filter be used for every service job.
Failure to use a filter will invalidate your warranty.
Do not expose Vacuum Pump to pressure. It is
protected by a pressure cut-off switch set at 25 psi
(+/- 5).
Maximum vacuum level 13 in. Hg while in Recovery
mode. The compressor is protected by a low pressure cut-out switch set at 13 in. Hg (+/- 3). Use
Vacuum mode to fully evacuate system.
The use of a filter will greatly reduce the risk of
damage to your ProVax, by preventing
foreign material from entering the unit.
Always empty refrigerant from the ProVax into a
storage tank; see Self-Purge procedure on Page 12.
Liquid refrigerant left in the ProVax’s condenser may
expand, causing damage to components.
Each filter should be labeled and used exclusively
for one type of refrigerant only.
Special care should be taken when recovering
from a "burned-out" system. Use two high acid
capacity filters, in series. (Alco type EK-162-F or
Sporlan type C-162-F are recommended )When
you have finished recovering from the system,
flush your ProVax with a small amount of clean
refrigerant and refrigerant oil to purge off any
foreign substances left in the unit.
If the unit is to be stored or not used for any length
of time, we recommend that it be complenty evacuated of any residual refrigerant and purged with dry
nitrogen.
5
ADDITIONAL RECOVERY TANK INFORMATION
m WARNING:
Also read the information pertaining to recovery tanks, previously listed under
Safety Information and Operating Guidelines.
Tanks and filters should be designated for one
refrigerant only. Before using a tank previously
used for another refrigerant, completely empty
the tank, evacuate it and purge the tank using dry
nitrogen, and then re-evacuate it.
m CAUTION: NEVER use a standard disposable
30 lb. (the type of container in which virgin refrigerant is sold) to recover refrigerant.
Use ONLY authorized refillable refrigerant tanks.
Federal regulations require refrigerant to be transported only in containers meeting DOT specs.
4BA or 4BW.
Always store refrigerant containers in a cool dry
place.
Do not mix refrigerants in a system, a tank or any
where else. Each type of refrigerant must have its
own tank, filter, etc.
mWARNING: DO NOT: Exceed the working pressure of each cylinder. Recovery cylinders are
designed for different pressures. Your ProVax
is not supplied with a recovery tank, it requires
the use of tanks with a minimum of 350 psi
working pressure and Promax strongly recommends the use of 400 psi tanks.
Storage cylinders sometimes have valves that are
not properly seated when manufactured. Keeping
caps on these valves will guard against refrigerant leakage.
Safety codes recommend that closed tanks not
be filled over 80% of volume with liquid. The
remaining 20% is called head pressure room.
NOTE: The use of a 400 psi tank is mandatory
when recovering R-410A.
See Promax Recovery Tanks under Parts and
Accessories section on Page 17.
m WARNING! NEVER TRANSPORT AN OVERFILLED CYLINDER
Refrigerant expands when it gets warm and may cause a tank to explode if overfilled.
CYLINDER TEMPERATURE
60°F
70°F
100°F
130°F
150°F
80%
81%
83%
90%
94%
90%
92%
96%
100%
STARTING WITH CYLINDER
80% BY VOLUME
SPACE OCCUPIED BY LIQUID
STARTING WITH CYLINDER
90% BY VOLUME
SPACE OCCUPIED BY LIQUID
6
PURGING NON-CONDENSABLE GASES
FROM REFRIGERANT TANK
1. Allow the tank to sit undisturbed for 24 hours. This
allows the air to rise to the top.
2. Connect a manifold to the tank and read the
amount of pressure in the tank by looking at the
output pressure gauge.
3. Determine the ambient temperature in the room.
4. Refer to a Refrigerant pressure/temperature chart.
Find the temperature on the chart and look across
to the corresponding pressure for the type of
refrigerant in the tank. Determine how that relates
to the reading on the gauge.
5. If the pressure reading is higher than the pressure
shown on the chart, very slowly (so as not to
cause turbulence inside the tank) crack open the
vapor port valve. Watch the pressure on the
gauge decrease. To prevent venting, add 4-5 psi
to the pressure shown on the chart.
When the gauge corresponds to that pressure,
close the vapor port valve.
6. Allow the tank to sit for 10 minutes and check the
pressure again.
7.Repeat the process again if necessary.
7
HELPFUL HINTS FOR
REFRIGERANT RECOVERY
Refrigerant recovery has come a long way in a few short years. On the surface it's simply the process of taking refrigerant out of a system and putting it into a tank. However, this simple process can quickly become problematic if a few
items are overlooked. The following are some tips and pointers we've accumulated over the last few years that can save
you time and make the process go smoother.
First you need to identify the refrigerant type and quantity in the system you are servicing. If you determine it’s a
burnout, you need a special tank (a tank that's identified as containing burnout or other unidentified gases), and you
need to use extra filtration prior to recovery. (See “special care” note on page 5).
If, on the other hand, you know the gas in the system is relatively clean or new, then a new tank should be used. If
you're planning on putting the refrigerant back into the same system after you have finished the service or if the refrigerant is going to be reclaimed, then use a tank that has the same refrigerant in it. A word of caution about the
Environmental Protection Agency (EPA): If you use a variety of refrigerant gasses in your service work - as evidenced by
your refrigerant purchases - and you only own one tank, you are asking for trouble. You would be well advised to own at
least one tank for every refrigerant type serviced, plus an extra for burnouts and other unknowns.
Results of Liquid Refrigerant
Trapped in a System
Pstart
PLANNING AHEAD
Forever
Pe
Knowing the quantity of refrigerant is important for planning storage requirements, as well as planning for the
actual recovery. For instance, any system with more than
5lbs. of refrigerant is likely to have areas where the liquid
can get trapped.
0
10” Hg
Tstart
The key to a quick recovery procedure is to get the liquid
out first, and then get the remaining vapor out. However
most systems are not "recovery friendly." That is they
don't have access ports at their lowest points. If some
units you're servicing are on maintenance contracts, you
would save significant time by installing access ports at all
of the lowest points in the system, where liquid is likely to
accumulate.
Time
Tfinish
HOSES AND VALVES
Hoses and Schraeder valves have a large impact on recovery speed. In general, the larger the hose, the less friction
on the flow of refrigerant, the quicker the recovery time.
Many contractors are now using 9.5mm (3/8') lines for
the input to the recovery machine, even those lines originating out of 6.3mm(1/4") fittings, and the shortest hose
possible.
Since most systems don't have these ports you need to
be prepared to boil off the trapped liquid with a heat gun,
when ever it's found. An indicator of trapped liquid in a
system is frost or condensation forming on the plumbing
or components where the liquid is trapped. The trapped
liquid may be in an area that is not visible. In all cases
trapped liquid in a system during recovery causes the
recovery process to slow down, regardless of the size or
type of machine (see diagram).
Schraeder valves must be removed from the connection
prior to an expedient recovery. Most wholesalers sell a
tool for removing these cores, while keeping the connection sealed. The core depressor, in the end of the hose,
should also be removed. These two items can turn a 20
minute job into one that goes on for hours. So, be sure to
remove the Schraeder valves and core depressors before
every recovery job.
If you are unable to locate the trapped liquid, but you
know it's there, because the recovery job is taking "forever". Turn on the system compressor (if it's operable) for a
few seconds, this will get the refrigerant moving to another part of the system and in the process pick up enough
heat to boil off.
Another hose consideration is the little rubber grommet at
the end of the hose that makes a seal with the flare fitting.
We've seen these seals so worn and deformed that when
the hose is connected to the flare fitting the grommet virtually seals off the connection.
8
HELPFUL HINTS FOR
REFRIGERANT RECOVERY - cont.
This is probably never noticed in charging, because the
pressure opens the grommet, but during recovery (or with
suction) the deformed grommet severely restricts the flow
of refrigerant.
KEEPING THE DIRT OUT
During the recovery process your recovery machine can be
exposed to debris that can, potentially, damage it. This
includes brazing spatter and copper/ brass slithers. Further
contamination can be introduced from the refrigerant storage tanks. To prolong the life of your recovery machine,
always use an inline filter at the inlet Port.
REFRIGERANT RECYCLING
Current regulations state that used refrigerant shall not be
sold, or used in a different owner's equipment, unless the
refrigerant has been laboratory analyzed and found to meet
the requirements of ARI 700 (latest edition). As a result,
recycling and verifying ARI 700 conformance isn't economically justified in most cases. It's still a great idea to do as
much cleaning of refrigerant going back into the same system (or owners system) as possible. We recommend using
the largest, high-acid capacity filter, that are economically
feasible. Put these filters on the suction or inlet side of the
recovery unit. Change filters often.
Whenever you are charging a system from a recovery cylinder it is a good idea to use an in-line filter to protect the system from contamination. Again, change your in-line filters
often.
GETTING THE LIQUID OUT
See diagram on page 13 of this manual
Push/pull is a method of removing bulk liquid from a system using the pressure differential created by the recovery
machine. Push-pull will generally not work on smaller systems because there is no bulk liquid reservoir to create a
siphon from.
The recovery of large amounts of liquid refrigerant can
sometimes carry with it large quantities of oil, if the system
being serviced doesn't have an adequate oil separator
installed. If this recovered refrigerant isn't going to be liquid
charged back into the same system, you might want to separate the refrigerant from the oil in order to measure the oil
(to know how much oil to charge back into the system).
Refrigerant sent back for reclaim does not need to have the
oil removed. One of the simplest and most cost effective
ways to achieve this is to use a 13.6kg or 22.7kg (30 or 50
lb.) tank in line with your recovery machine. Connect the
system to the liquid port of the tank, then from the vapor
port of the tank connect to the input of your recovery
machine. A second tank, for storing refrigerant, should then
be connected to the output of the recovery machine. If you
encounter large amounts of liquid you will need to put a
band heater around the first tank. When the recovery job is
complete the oil can be removed, from the first tank, by
applying a small amount of pressure, using nitrogen, to one
of the ports and extracting the oil from the other. If you are
going to remove the oil from the vapor port you will need to
turn the tank upside down. Always wear safety glasses
when performing this operation as the oil may be acidic and
could cause severe burning.
Push-pull is mostly used on systems with a receiver tank or
those with greater than 9.1kg (20 lbs.) of refrigerant, or
when transferring from one tank to another. The rate of liquid transfer is very much dependent on hose size, with larger hoses providing much better throughput.
Another trick is to cool the tank, if it's partially filled, prior
to or during recovery. This operation will lower the pressure
in the storage tank and therefore speed up recovery. There
must be a minimum of 2.3kg (5 lbs) of liquid refrigerant in
the tank you wish to chill. This operation can be performed
prior to or during the recovery. See the two set up diagrams
and procedures on pages 13-14 of this manual.
There is nothing magic here, you are simply using your
recovery machine to make a refrigerator where the tank is
the evaporator. By throttling the output valve, you're effectively creating a capillary tube or an expansion device, but
you need to adjust the back pressure to suit the conditions
and the refrigerant. Five to ten minutes of chilling can produce some very dramatic tank cooling, depending on the
conditions. If there are any non condensables in the tank
this process will not work. The greater the quantity of refrigerant in the tank the longer the process will take.
9
OPERATING YOUR ProVaxTM
ProVaxTM Control Panel Overview
Inlet Pressure
Gauge*
Outlet Pressure
Gauge
Recovery/Purge
Selector
Powers Unit &
Turns on Cooling
Fans
High Pressure
Selection
Off - 400psi
ON - 550psi
Recovery
Outlet
Port
Starts
Compressor/Vacuum Pump
Recovery
Inlet Port and
Liquid/Vapor
Adjustment
Recovery/Evacuate
Mode Selector
Recovery/Evacuation
Inlet Port
Note: *Promax recommends the use of either the Robinair 14010A or
14830A Thermistor Vacuum Gauge to monitor vacuum level
10
Recovery
Outlet Port
OPERATING YOUR ProVaxTM
PROCEDURE FOR NORMAL SYSTEM RECOVERY
1. Inspect the ProVax thoroughly to insure that
it is in good operating condition.
10. Open the output valve/knob (RED) on the
ProVax.
2. Ensure that the outlet valve/knob (RED) and the
inlet valve/knob (BLUE) on the ProVax are in
the closed positions.
11. Slowly open the input valve/knob (BLUE) on the
ProVax.
a. If the compressor starts to knock, slowly
throttle back the input valve/knob until the
knocking stops.
b. If the input valve was throttled back, it should
be fully opened once the liquid has been
removed from the system (the manifold
gauge set vapor port should also be opened
at this time).
12. The ProVax will automatically stop after the
refrigerant has been removed and it reaches
10” to 20" hg vacuum.
3. Set the "Mode" valve/knob (Yellow) to “Recovery”
4. Set the "Recover/Purge" valve/knob (BLACK)
to "Recover".
5. Connect ProVax to the system being serviced,
making sure all connections are correct and
tight. (see set-up diagram).
6. Open the liquid port of the recovery cylinder
(always open valves slowly to check hoses and
connections for leaks).
7. Open the liquid port on your manifold gauge set.
Opening the liquid port will remove the liquid
from the system first, greatly reducing the recovery time. (after the liquid has been removed,
open the manifold vapor port to finish evacuating
the system).
Note: Anytime you want to pause an operation, you
can stop the unit by turning the "MODE" valve/knob
(YELLOW) to “Stop”.
Note: To restart, turn the Recover/Purge valve/knob
(BLACK) to “Recover” and the input valve/knob
(BLUE) to “Closed” and press the “Start” switch.
13.
14.
Note: The ProVax uses an "oil-less" compressor
during recovery. It is lubricated with the oil suspended in the refrigerant. Ensure there is refrigerant up
to the ProVax inlet valve prior to turning on the unit.
8. Connect your ProVax to Power.
15.
Close the manifold gauge set’s vapor and
liquid ports.
Turn the ProVax input valve/knob (BLUE) to
the “Closed” position.
Proceed with the Self Purge and Vacuum.
(see Self Purge/Vacuum procedure
on page 12).
Note: Always purge the ProVax after each
use. Failure to purge the remaining refrigerant from
the ProVax could result in the acidic degradation
of internal components, ultimately causing
premature failure of the unit.
9. Place "High Pressure Shut Off Select”
switch in the desired position.
Note: When the High Pressure Select switch is in
the ON position, the unit will shut off at 550 PSI
(for R410A). In the OFF position it will shut off at 400
PSI.
a. Turn on the "Power" switch. You should hear
the cooling fans running
b. Press the "Start" switch. This momentary
switch will start the compressor/motor.
11
OPERATING YOUR Provax - cont.
PROCEDURE FOR SELF PURGE
8. Close the recovery tank valves and close
the Outlet valve/knob (RED) and Inlet valve/knob
(BLUE) on the ProVax.
9. Turn the ProVax “Power” switch "Off".
10. Return the Recover/Purge valve/knob (BLACK)
knob to the "Recover" position.
11. Turn the Inlet valve/knob (BLUE) to the "Closed"
position.
12. Disconnect and store all hoses.
1. Ensure the "MODE" valve/knob (YELLOW) is in
the "Recovery" position.
2. Ensure the Recover/Purge valve/knob (BLACK)
is the “Recover” position.
Note: will be moved to “Purge” position after
start.
3. Turn the input valve/knob (BLUE) to Purge
4. Restart the ProVax.
a. Power "On"
b. Press "Start"
5. Turn the Recover/Purge valve/knob (BLACK) to
the "Purge" position.
6. Open the Output valve/knob (RED)
7. The ProVax will automaticaly stop after the unit
is purged and it reaches 10” to 20” hg vacuum.
Note: It is recommended that the in-line filter/dryer
be replaced after every recovery job.
PROCEDURE FOR PULLING A VACUUM
mWARNING: Do not expose the inlet-port of the
4. Turn "MODE" valve/knob (YELLOW) to "Vacuum"
position
5. Start unit.
a. Power "On"
b. Press "Start"
6. Run until desired vacuum is reached
7. To stop, rotate "MODE" valve/knob (YELLOW) to
the "Stop" position.
8. Cap inlet port to prevent contamination.
ProVax to pressure while in the Vacuum Mode
1. Turn BLUE valve/knob to "Closed" position
2. Turn Recover/Purgevalve/knob (BLACK) to
“Recover”
3. Turn output valve/knob (RED) to "Closed"
DIAGRAM FOR REFRIGERATION RECOVERY
THIS IS THE FASTEST METHOD FOR RECOVERING VAPOR REFRIGERANT
OPTIONAL MOISTURE
SIGHT GLASS
MANIFOLD
GAUGE
SET
INPUT
SYSTEM BEING
SERVICED
OUTPUT
LIQUID
VAPOR
mWARNING! SCALE MUST BE USED
TO AVOID OVER FILLING THE STORAGE TANK
12
LIQUID
DIAGRAM FOR “PUSH/PULL” METHOD
Push/pull method only works with large systems where the liquid is readily accessible. Do not use this
method on systems that contain less than 6.8 kg (15 lbs.) as it may not work.
The sight glass is used to provide a method of determining the moisture content and quality of a system’s
refrigerant.
m CAUTION: When using the “Push/Pull” method, once the siphon is started, it can continue and overfill
the storage tank even if the tank is equipped with a float level sensor. The siphon can continue even
when the machine is turned off. You must manually close the valves on the tank and the unit to prevent
overfilling of the recovery tank.
1. Close INPUT and OUTPUT valves
2. Turn MODE knob to "RECOVERY"
3. Turn RECOVERY/PURGE knob to "RECOVER"
4. Start machine
5. Open INPUT valve to the "VAPOR" position and
OUTPUT valve to "OPEN"
6. When the refrigerant scale stops rising, close all
ports
CAUTION: Do not overfill tank
7. Turn MODE knob to "STOP"
8. Switch off machine
INPUT
SYSTEM BEING
SERVICED
VAPOR
OUTPUT
LIQUID
LIQUID
OPTIONAL MOISTURE
SIGHT GLASS
m Warning ! A scale must be used to avoid
over filling the storage tank.
SET-UP DIAGRAM FOR TANK
PRE OR SUB COOLING PROCEDURE
See page 9 for more information on Sub Cooling.
Note: To begin this process you must have a minimum
of 5 lbs. of liquid refrigerant in the tank. If this is not the
case, using a fully evacuated empty tank will help you
achieve the fastest recovery time.
INPUT
OUTPUT
VAPOR
LIQUID
1. Close INPUT and OUTPUT valves
2. Turn MODE knob to "RECOVERY"
3. Turn RECOVERY/PURGE knob to "RECOVER"
4. Start machine
5. Open INPUT valve to the "LIQUID" position
6. Throttle the OUTPUT valve so that the output pressure is 100 psi greater than the input pressure, but
never more than 300 psi
7. Run until tank is cold
13
OPTIONAL RECOVERY/TANK PRE OR SUB
COOLING FOR FIXED HOSE SET-UP
MANIFOLD
GAUGE
SET
INPUT
SYSTEM BEING
SERVICED
LIQUID
VAPOR
LIQUID
OUTPUT
m WARNING!
A scale must be used to avoid over filling the storage tank.
NORMAL RECOVERY:
Tank Vapor valve is closed
TANK PRE OR SUB COOLING:
Tank Vapor valve is open and both manifold gauge set valves are closed.
14
VACUUM PUMP MAINTENANCE
Vacuum
Pump Oil
For maximum performance, Promax recommends changing vacuum pump oil after each
use.
The condition and type of oil used in any high vacuum pump are extremely important in
determining the ultimate attainable vacuum. Promax recommends the use of Robinairs
Premium High Vacuum Pump Oil.
This oil has been specifically blended to maintain maximum viscosity at normal running
temperatures and to improve cold weather starts.
Robinair Premium High Vacuum Pump Oil is available in handy quart containers or in
convenient gallon containers. Order by part number:
13119 — Pint (shipped 12 pints per case)
13203 — Quart (shipped 12 quarts per case)
13204 — Gallon (shipped 4 gallons per case)
VACUUM PUMP OIL CHANGE PROCEDURE
1. Warm up the vacuum pump by running:
a. Place a cap on the inlet port
b. Turn Mode knob (Yellow) to "Vacuum"
c. Turn on "Power" switch
d. Press "Start" switch
e. Run for 2 minutes and then turn off power.
Note: ProVax inlet gauge does not indicate vacuum level.
Use a separate vacuum gauge to observe vacuum level.
2.
3.
4.
5.
6.
7.
8.
9.
FILLER CAP CAP
OILOILFILLER
OIL DRAIN
OIL DRAINCAP
CAP
Unplug unit from power source
Place ProVax on a raised surface, with oil drain plug on the bottom of the unit exposed
Place a suitable container under drain plug
Remove OIL FILL cap
Remove OIL DRAIN cap
Drain oil into container until flow of oil has completely stopped
Replace the OIL DRAIN cap
Fill oil reservoir with new vacuum pump oil until oil just shows at of bottom of the sight
glass. The approximate oil capacity is 15 ounces.
10. Be sure the inlet port is capped and TURN ON vacuum pump (see step 1)
11. Allow pump to run for one minute, then check the oil level. If the oil is below the sight glass
OIL FILL line, add oil slowly (while pump is running) until the oil reaches the OIL LEVEL line.
12. Replace the OIL FILL cap, making sure the inlet is capped and the drain cap is tight.
15
ProVaxTM DIAGRAM
Front
(Section 1)
14
16
15
17
3
12
Back
(Section 4)
1
13
2
7
6
4
11
10
Control Panel
(Section 2)
5
Motor/Compressor/Pump
(Section 3) (Note: For compressor Repair Kits
8
see page 17)
9
Section 1 - ProVax Front:
Section 3 - ProVax Motor/Compressor/Vacuum Pump:
Item.#
(14)
(15)
(16)
(17)
Item.#
(8)
(9)
(10)
N/S
N/S
N/S
Part#
527075
100343
100345
527374
Description
Front & Rear Case, plastic (set)
Filter Drier
4" Blue Hose
Rubber Foot
Section 2 - Provax Control Panel:
Item.#
(11)
(12)
(13)
N/S
N/S
N/S
N/S
N/S
N/S
N/S
N/S
N/S
N/S
N/S
N/S
N/S
N/S
Part#
527080
GA1500
GA0800
GA1000
528160
NB6501
EL1309
EL1310
527376ASM
EL2800
EL2802
113726
120106
100122
100123
100124
527845
Description
Front Panel
Pressure Gauge, 500 Psi
Pressure Gauge, 800 Psi
Gauge Lens
Inlet & outlet Fitting 45 degree
Inlet & outlet Fitting Protection Cap
Start Switch, momentary
ON-OFF Switch
Manifold Assembly
Pressure Sensor (400psi)
High Pressure Sensor (500psi)
Vacuum Switch (13in Hg)
Vacuum Protection Switch
Black Knob
Blue Knob
Red Knob
Yellow Knob
Part#
527835ASM
525935
527834ASM
527069ASM
528167ASM
527086
Description
Compressor Assembly
Motor, 115V, 60Hz
Vacuum Pump Assembly
Vacuum Pump Clutch Assy
Compressor Clutch Assy.
Vacuum Pump & Motor "Vibration"
Mount
Section 4 - ProVax Back:
Item.#
(1)
(2)
(3)
(4)
N/S
N/S
(5)
(6)
(7)
N/S
N/S
N/S
N/S
N/S
N/S
N/S
16
Part#
527075
100478
527073
527074
529931
527077
EL1817
EL1412
110969
NB6501
EL1500
527084
527085
527076
529925
111443
Description
Front & Rear Case, plastic (set)
Condenser
Handle
Wheel
Retaining ring, wheel
Axle, wheel
Axial Fan
Start Capacitor
Oil Filler Cap
Oil Drain Cap
Relay
Compressor Grill
Vacuum Pump Grill
Fan Grill
Bumper
Power Cord, 115V/60Hz
REPLACEMENT KITS
PART#
13119
15367
DESCRIPTION
PREMIUM HIGH VACUUM PUMP OIL, PINT BOTTLE (case of 12)
VACUUM PUMP SEAL REPLACEMENT KIT
KT3302
KT3303
KT3307
KT3308
PISTON SEAL REPLACEMENT (middle section of compressor)
VALVE REPLACEMENT KIT (top section of compressor)
COMPRESSOR REPAIR KIT (all three sections of compressor)
SHAFT REPLACEMENT KIT (bottom section of compressor)
RECOMMENDED ACCESSORIES
PART#
KT-5002
RGT30
RGT30NS
RGT50
RGT50NS
RGT50HP
10994
ADS-100
41670
416330
14830A
16910
16440
4650
TIFZX-1
DESCRIPTION
80% CAPACITY TANK SENSING KIT
30 LB RECOVERY TANK (350 psi working pressure) with capacity sensor
SAME AS RGT30, WITHOUT SENSOR
50 LB RECOVERY TANK (350 psi working pressure) with capacity sensor
SAME AS RGT50, WITHOUT SENSOR
50 LB RECOVERY TANK, HIGH PRESSURE (400 psi working pressure) with capacity sensor
HEATER BLANKET
REFRIGERANT SCALE, 200LB CAPACITY, WITH REMOVABLE PLATFORM
HIGH PRESSURE MANIFOLD SET, 60” COLOR CODED HOSES, FOR R410A
TWO WAY MANIFOLD SET, 72” COLOR CODED HOSES, FOR R22 AND R134a
THERMISTOR VACUUM GAUGE
REFRIGERANT IDENTIFIER
CORDLESS RECHARGEABLE 30-LED LIGHT
MIRROR AND MAGNET SET
HEATED PENTODETM REFRIGERANT LEAK DETECTOR
NOTE: For details see: www.AdvancedTestProducts.com
17
5
3
GRN
WHT
(NEUTRAL)
0
GRN
R121917
RECEPTACLE
2
WHT
BLK
BRN
18
YEL
73
BLK
BRN
YEL
51
BLK
BRN
EL1817
FAN
10
8
43
71
BLK
EL1412
STARTING CAPACITOR
WHT
BRN
EL1817
FAN
4
EL1310
POWER SWITCH
45
98
12
72
70
GRN
18
16
BLK
14
EL1500
RELAY
99
3
5
6
7
BLK
ORG
6
8
2
7
4
1
3
62
WHT
MAIN
BLK
BLUE
START
MOUNT STUD
525935
MOTOR
CENTRIFUGAL SWITCH
Thermal Protector
ORANGE
TH1
22
31
33
4
1
2
RED
BLK
BLU
29
67
30
49
25
32
BLK
61
RED
23
WHT
WHT
7
24
21
65
BLK
113726
LOW PRES. SW
WHT
528161 (2X)
SWITCH BANK
LEFT
WHT
27
EL2802
PRESSURE SWITCH
WHT
EL1310
SELECTOR SWITCH
37
WHT
35
EL1309
START SWITCH
20
47
60
34
41
WHT
39
19
WHT
BLK
528161 (2X)
SWITCH BANK
RIGHT
28
1
JUMPER (REMOVE
WHEN USING TANK
SENSOR CORD)
WHT
63
RED
13
WHT
15
17
26
BLK
BLK
WHT
WHT
WHT
EL2800
PRESSURE SWITCH
GRN
GRN
0
120106
VAC PROTECT SW
EL1214
3 PIN CONNECTOR
FOR UPGRADE
EL1420
TANK SENSOR
CORD
(OPTION)
ProVaxTM WIRING DIAGRAM
INSTALLATION OF OPTIONAL 80% TANK SHUT-OFF KIT
CAPACITY SENSING COMPONENTS (P/N:KT-5002)
m WARNING: Prior to performing any type of maintenance work on your ProVax, insure that it is disconnected from the power supply before you begin.
10. To test the installation:
NOTE: Refer to the wiring diagram on page 17 during the installation of your kit.
1. Disconnect your ProVax from the power source.
2. Remove the case fasteners and separate the front
half of the ProVax.
a. Attempt to start the ProVax without the sensor
cord attached to a tank. The ProVax’s
compressor should not start up.
b. Turn the ProVax off and attempt to start the
ProVax with the sensor tank connected to a
tank. The unit should function normally.
Disconnecting the sensor cord while the unit
is running should cause the unit to shut down.
11 If your unit does not function as described
above, DISCONNECT the ProVax from the
power supply, and re-check your connections
per the steps above and the wiring diagram on
page 17.
3. Identify white "jumper wire," located below hole in
lower right corner of the front panel, designated
for the tank sensor cord.
Note: Jumper wire identified with a tag.
4. Disconnect jumper where tagged and secure it to
nearest wire bundle, using wire tie provided.
5. Route tank sensor cord (EL1420) through the hole
in the front panel, passing the "tank connector"
end through from the backside.
6. Secure the tank sensor cord in the hole with the
strain relief grommet provided.
7. Connect the 3-pin male connector (white) supplied
with the KT5002 to its counterpart, pre-wired
inside your ProVax.
8. Secure any loose wiring with the wire ties
provided.
9. Replace the plastic case halves and fasteners.
19
TROUBLESHOOTING YOUR ProVax
SAFETY FIRST
Read and understand all safety information contained
in this manual before servicing the unit.
FAN IS RUNNING
NO
WHEN POWER SWITCH
IS IN “ON” POSITION
YES
IS UNIT IN HIGH
PRESSURE
SHUT OFF?
UNIT PUMPS INTO
NO
HIGH PRESSURE SHUT
OFF
YES
ARE VALVES OPEN?
CHECK
FOR SCHRADER
VALVES
NO
ARE YOUR HOSES
TIGHT? DO YOU
HAVE LEAKS?
YES
IS THE TANK
CORD ATTACHED
TO THE TANK
YES
NO
YES
NO
DO YOU HAVE
115V SUPPLY?
YES
YES
YES
YES
NO
YES
COMPRESSOR STARTS NO
WHEN START SWITCH
IS PRESSED
UNIT PULLS
INTO A VACUUM
CHECK POWER
SUPPLY
DOES TANK FLOAT
SWITCH WORK
PROPERLY?
YES
NO
DOES UNIT PULL A
NO
VACUUM WHEN INPUT
VALVE IS CLOSED?
YES
TROUBLESHOOTING ENDS
20
NO
CALL YOUR LOCAL PROMAX DISTRIBUTOR
CONNECT UNIT
TO 115V
TROUBLESHOOTING GUIDE
Vacuum Pump
Your CoolTech® pump has been designed for dependable use and long life. If something
should go wrong, however, the following guide will help you get the pump back in service as
quickly as possible.
If disassembly of the pump is required, please check your warranty. The warranty may be
voided by misuse or customer tampering, which results in the pump being inoperable.
Oil
Leakage
1.Be sure the oil is not a residual accumulation from spillage, etc.
2. If leakage exists, the module cover gasket or the shaft seal may need replacing. Follow
the instructions supplied with the Seal Replacement Kit, part number 15367. If leakage
exists in the area of the oil drain plug, you may need to reseal the plug using a commercial pipe thread sealer.
Failure
To Pull
A Good
Vacuum
1. Be sure the vacuum gauge and all connections are in good condition and leak-free.
You can confirm leakage by monitoring the vacuum with a thermistor gauge while applying
vacuum pump oil at connections or suspected leak points. The vacuum will improve briefly
while the oil is sealing the leak.
2. Be sure the pump oil is clean. A badly contaminated pump may require several oil flushes.
See OIL CHANGE PROCEDURE.
Note: Use only high vacuum pump oil such as Robinairs’ Premium High Vacuum Pump Oil.
Other oils will prevent pull-down to a deep vacuum.
3. Be sure the oil is at the proper level. For maximum pump operation, the oil must be even
with the OIL LEVEL line on the sight glass when the pump is running. See OIL CHANGE
PROCEDURE. Do not overfill —operating temperatures will cause the oil to expand so it
will appear at a higher level than when the pump is not running. To check the oil level,
start the pump with the inlet capped. Check the oil level in the sight glass. Add oil if necessary.
21
SPECIFICATIONS
Recovery Section
Vacuum Section
Refrigerants
Cat. III: R-12, R-134a, R-401C, R-406A, R-500,
Cat. IV: R-22, R-401A, R-401B, 402B, R-407C,
R-407D, R-408A, R-409A, R-411A, R-411B, R-412A,
R-502, R-509, Cat. V: R-402A, R-404A, R-407A,
R-407B, R-410A, R-507
same
Power (+/- 10%)
115VAC 60 Hz
same
Motor
1/2 HP, AC, cap start, inductive run, brushless
Motor Speed
1725 RPM
same
Current Draw
Full Load: 10 amps @ 115 VAC; Locked Rotor: 23.1 amps
n/a
Compressor Type
Proprietary "Oil-less," air cooled, piston style,
KynarTM poppet valves, triple teflonTM ceramic polymer
piston seals
n/a
High Pressure Shut-off
Selectable: 400 or 550 psi
n/a
Recovery low pressure
Cut-Out Switch
13in Hg (+/ -3)
n/a
Refrigerant Class
Refrigerant Recovery
Rate: Push/Pull
Category III
8.00 Lbs./min.
3.63 kg/min
Refrigerant Recovery
Rate: Liquid
3.46 Lbs./min.
1.57 kg/min.
Refrigerant Recovery
Rate: Vapor
0.24 Lbs./min.
0.11 kg/min.
Category IV
9.52 Lbs./min.
4.32 kg/min
Category V
10.82 Lbs./min.
4.91 kg/min.
3.99 Lbs./min.
1.81 kg/min.
4.08 Lbs./min.
1.85 kg/min.
0.33 Lbs./min.
0.15 kg/min.
0.35 Lbs./min.
0.16 kg/min.
n/a
n/a
n/a
Vacuum Pump Type
n/a
Offset Rotary Vane
Stages
n/a
2 Stage
Free Air Displacement
n/a
6 CFM
Factory Micron Rating
n/a
20 microns
Approx. Oil Capacity
n/a
15 oz.
Maximum Vacuum Pump
Protection Cut-off Switch n/a
25psi (+ / - 5)
Operating Temp.
32° F to 155° F
same
Dimensions
25" H X 22" W X 10" D
n/a
Weight
57 lbs
n/a
EPA Certification
ARI-740 by UL® (control no.8EA7)
n/a
22
FULL ONE YEAR WARRANTY
MFG #
Promax products are warranted to be free from defects in workmanship and materials for a period of one
year from date of purchase.
THE FOLLOWING RESTRICTIONS APPLY:
1. The warranty applies to products in normal use only, as described in the operating manual. The product
must also be serviced and maintained as described therein.
2. If the product fails, it will be replaced at the option of Advanced Test Products, Inc. (ATP)
3. Warranty service claims are subject to factory inspection for product defect(s). If during the warranty evaluation it is determined that a filter has not been used or that the filter was not properly maintained or that
the machine has been used in any way other than the purpose for which it was designed, ATP, reserves
the right to void the warranty.
4. All warranty claims must be made within the warranty period. Proof of purchase must be supplied .
This warranty is non-transferable.
5. Please note that the warranty does not apply if the product or product part is damaged by accident, misuse, tampered with or modified in any way.
6. Normal wear items (seals, filters, etc.) are specifically excluded from warranty, unless found by Promax
to be defective.
WARRANTY SERVICE
This warranty is given by ADVANCED TEST PRODUCTS, INC.
Service under this warranty must be obtained by the following steps:
1. Outside the U.S.A. contact your local Promax Distributor.
2. Inside the U.S.A. call 1.800.327.5060 or 954-499-5400
for a return material authorization (RMA) number.
23
THE UNITED STATES ENVIRONMENTAL PROTECTION
AGENCY (EPA) REFRIGERANT RECOVERY AND RECYCLING DEVICE
ACQUISITION CERTIFICATION FORM
EPA regulations have required establishments that service or dispose of refrigerant or air conditioning
equipment to certify that they have acquired recovery and recycling devices that meet the EPA standards
for such devices since August 12. 1993. To certify that you have acquired equipment, please complete this
form according to the instructions and mail it to the appropriate EPA Regional Office. BOTH THE
INSTRUCTIONS AND MAILING ADDRESS CAN BE FOUND ON THE NEXT PAGE OF THIS MANUAL.
UNIT STORAGE ADDRESS
Part 1: ESTABLISHMENT INFORMATION
Name of Establishment
Name of Establishment
Street
Street
State
City
Zip Code
(Area Code)
County
City
Telephone Number
State
Zip Code
(Area Code)
County
Telephone Number
NUMBER OF SERVICE VEHICLES BASED AT ESTABLISHMENT
Part 2: REGULATORY CLASSIFICATION
Identify the type of work performed at your establishment. Check all boxes that apply.
Type A - Service small appliances.
Type B - Service refrigeration or air conditioning equipment other than small appliances.
Type C - Dispose of small appliances
Type D - Dispose of refrigeration or air conditioning equipment other than small appliances.
Part 3: DEVICE IDENTIFICATION
Name of Device Manufacturer
Model #
Mfg# (if any)
Month/Year
Self Contained
Part 4: SIGNATURE
I certify that the establishment named in part 1. has acquired the refrigerant recovery or recycling
devices listed in part 3. and that this equipment will be properly used in service (and/or) disposing
of appliances. I also certify that the information supplied herein is correct and true.
Signature of owner / Responsible Officer
Date
Name (please print)
Title
Public reporting burden for this collection of information is estimated to vary from 20-60 minutes per response with an average of 40
minutes per response including time for reviewing instructions, searching existing data sources, gathering and maintaining the data
needed and completing the collection of information. Send comments regarding the burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden to: Chief information Policy Branch EPA, 401 M St. S.W. (PM223Y),
Washington, DC 20460 and to the Office of information and Regulatory Affairs, Office of Management and Budget, Washington, DC
20503 marked Attention, Desk Officer for EPA.
DO NOT SEND THIS FORM TO THE ABOVE ADDRESSES. ONLY SEND COMMENTS TO THESE ADDRESSES
24
INSTRUCTIONS EPA REGIONAL OFFICES
Part 1. Please provide the name, address and telephone
number of the establishment where the refrigerant recovery or recycling device(s) is (are) located. Please complete one form for each location. State the number of
vehicles based at this location that are used to transport
technicians and equipment to and from service sites.
CONNECTICUT, MAINE, MASSACHUSETTS, NEW
HAMPSHIRE, RHODE ISLAND, VERMONT
CAA 608 Enforcement Contact: EPA Region 1.
Mail Code APC, One Congress Street, John F. Kennedy
Federal Building, Boston, MA 02203-0001
Phone: (617) 565-3420
Part 2. Check the appropriate box for the type of work
performed by technicians who are employees of the
establishment. The term "small appliance" refers to any of
the following products that are fully manufactured,
charged and hermetically sealed in a factory with five or
less pounds of refrigerant:
NEW YORK, NEW JERSEY, PUERTO RICO, VIRGIN
ISLANDS CAA 608 Enforcement Contact: EPA Region 2.
290 Broadway, New York, NY 10007-1866
Phone: (212) 637-3000
DELAWARE, DISTRICT OF COLOMBIA, MARYLAND,
PENNSYLVANIA, VIRGINIA, WEST VIRGINIA
CAA 608Enforcement Contact: EPA Region 3. Mail Code
3AT21, 1650 Arch Street, Philadelphia, PA 19103-2029
Phone: (215) 566-5000
Refrigerators or freezers designed for home use, room air
conditioners (including window air conditioners and packaged thermal air conditioners), packaged thermal heat
pumps, dehumidifiers, under-the-counter ice makers,
vending machines and drinking water coolers.
ALABAMA, FLORIDA, GEORGIA, KENTUCKY, MISSISSIPPI, NORTH CAROLINA, SOUTH CAROLINA, TENNESSEE
CAA 608 Enforcement Contact: EPA Region 4. Mail Code
APT-AE, 100 Alabama Street, SW, Atlanta, GA 30303
Phone: (404) 562-8357
Part 3. For each recovery or recycling device acquired,
please list the name of the manufacturer of the device
and (if applicable) its model number and manufacturer
number. If more than 8 devices have been acquired
please fill out an additional form and attach it to the first
one.
Recovery devices that are self-contained should be listed
first and should be identified by checking the box in the
last column on the right. A self-contained device is one
that uses it's own pump or compressor to remove refrigerant from refrigeration or air conditioning equipment. On
the other hand, system dependent recovery devices rely
solely upon the compressor in the refrigeration or air conditioning equipment and/or upon the pressure of the
refrigerant inside the equipment to remove the refrigerant.
If the establishment has been listed as Type B and/or
Type D in Part 2, then the first device listed in Part 3 must
be a self-contained device and identified as such by
checking the box in the last column on the right.
If any of the devices are homemade, they should be identified by writing "homemade" in the column provided for
listing the name of the device manufacturer. Homemade
devices can be certified for establishments that are listed
as Type A or Type B in Part 2 until (six months after promulgation of the rule). If a Type C or Type D establishment
is certifying equipment after (six months after promulgation of the rule), then it must not use these devices for
service jobs classified as Type A or Type B.
Part 4. This form must be signed by either the owner of
the establishment or another responsible officer. The person who signs is certifying that the establishment has
acquired the equipment, that the establishment is complying with Section 608 regulations and that the information
provided is true and correct.
Send your form to the EPA office listed under the state or
territory in which your establishment is located.
ILLINOIS, INDIANA, MICHIGAN, MINNESOTA, OHIO,
WISCONSIN
CAA 608 Enforcement Contact: EPA Region 5. Mail Code
AT18J, 77 West Jackson Blvd., Chicago, IL 60604-3507
Phone: (312) 353-2000
ARKANSAS, LOUISIANA, NEW MEXICO, OKLAHOMA,
TEXAS
CAA 608 Enforcement Contact: EPA Region 6. Mail Code
6T-EC, Fountain Place, 12th Floor, Suite 1200
1445 Ross Avenue, Dallas, TX 75202-2733
Phone: (214) 665-6444
IOWA, KANSAS, MISSOURI, NEBRASKA
CAA 608 Enforcement Contact: EPA Region 7. Mail Code
ARTX/ARBR, 901 N. 5th Street, Kansas City, KS 66101
Phone: (800) 223-0425
COLORADO, MONTANA, NORTH DAKOTA, SOUTH
DAKOTA, UTAH, WYOMING
CAA 608Enforcement Contact: EPA Region 8. Mail Code
8AT-AP, 999 18th Street, Suite 500
Denver, CO 80202-2466
Phone: (303) 312-6312
AMERICA SAMOA, ARIZONA, CALIFORNIA, GUAM,
HAWAII, NEVADA
CAA 608 Enforcement Contact: EPA Region 9. Mail Code
A-3, 75 Hawthorne Street, San Francisco, CA 94105
Phone: (415) 744-1305
ALASKA, IDAHO, OREGON, WASHINGTON
CAA 608Enforcement contact: EPA Region 10.
Mail Code AT-082, 1200 Sixth Ave.
Seattle, WA 98101
Phone: (206) 553-1200
25
NOTES:
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
ADVANCE TEST PRODUCTS
Miramar, FL
Telephone: (954) 499-5400 • Fax: (954) 499-5454 • Toll Free: (800) 327-5060
www.ProVaxAC.com
Made in USA
527844Pro RevA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement