Barco CR series User manual

Barco CR series User manual
an
an introduction
introduction to
to
the
the projector
projector
CR series
User Manual
Manual
User
www.barco.com
english
CR series
User Manual - Introduction
2
1Introduction
6
1.1 Thank you
1.2Features
2
Safety Instructions
9
2.1SAFETY
2.2 GENERAL WARNINGS
2.2.1
INFORMATION AND WARNING ABOUT POTENTIAL HEALTH ISSUES RELATED TO MERCURY
VAPOR (UHP lamps only)
2.2.2
HEAVY DUTY AND CONTINOUS USE (UHP lamps only)
2.2.3
SERVICE PERSONNEL INFORMATION WARNING (UHP lamps only)
2.2.4
REMOTE CONTROL WARNING
2.2.5
WARNING SYMBOLS
2.3FCC
2.4 WEEE INFORMATION
2.5 ENVIRONMENTAL INFORMATION
2.5.1
Disposal Information
2.5.2
Disposal of batteries in the product
2.6 SERVICE INFORMATION
3
4
What’s in the box?
13
Getting to know the projector
15
4.1Overview
4.2Indicators
4.2.1
The status indicator
4.2.2Keypad
4.2.3
Remote control
4.3Connectivity
4.4 Graphical User Interface (GUI)
5
Basic setup
5.1Lens
5.1.1
Lens and lens mount
5.1.2
Inserting a lens
5.1.3
Replacing a lens
5.2 Adjusting on screen image size and position
5.3 Lamp operation
5.4 Projector rotation
3
21
english
1 Contents of this User’s Guide
english
5.5 Ceiling mount
5.5.1
Ceiling mount cover (optional)
5.5.2
Attaching the ceiling cover
5.6 Connection and cables
5.6.1
Setting up a video source
5.6.2
Setting up a computer source
5.6.3
Connecting command and control interfaces
5.6.4
Attaching X-PORT™ modules
5.7
Using X-PORT™ modules
5.7.1
X-PORT DCC120
5.7.2
X-PORT 3G-SDI
5.7.3
X-PORT HDMI 3D
5.8 Image alignment
5.9 Setting image orientation
5.10Using source scan
5.11Limiting OSD messages
5.12Changing the language of the menu system
5.13Identifying system status
5.13.1
Getting information about the active source
5.14Using the dual lamp system (UHP
5.15Configuring 3D (AS3D)
5.16Image sizes
6
models only)
Advanced setup
35
6.1 Controlling multiple projectors with remote control ID (RCID)
6.2 Protecting the projector with a pin code
6.3 Using dual head input
6.4 Multi-channel 3D synchronization
6.4.1
Synchronous frame sequential
6.4.2
Asynchronous frame sequential
6.4.3
Synchronous side-by-side
6.4.4
Asynchronous side-by-side
6.5 Setting custom color space and digital level
6.6 Disabling IR receivers
6.7 Controlling screens with triggers
6.8 Setting aspect trigger behavior
6.9 Automatic power on/off
6.9.1
Using the timer
6.9.2
Using DPMS (Display Power Management Signaling)
6.10Disabling LED indicators
6.11Setting the background color
6.12Selecting the startup logo
CR series
User Manual - Introduction
4
7
Optimising the picture
43
7.1 Calibration data
7.1.1
Updating RealColor™ calibration data
7.2
Working with RealColor™
7.2.1
Setting the BrilliantColor™ correctly
7.2.2 Gamma
7.2.3
RealColor™ operating modes
7.2.4
Setting a white point or color temperature
7.2.5
Defining the system color gamut
8Maintenance
49
8.1 Software upgrades
8.2 Lamp replacement (UHP units only)
9
Technical specifications
9.1 Product details
5
51
english
6.13Setting OSD menu timeout
6.14Selecting the startup logo
english
1 Introduction
1.1 Thank you
Thank you for purchasing this projector.
When referring to the term CR-series in this document,it means that the content is applicable
for following Barco products:
•
CRPN-62B
•
CRWQ-62B
The CR series projectors set an industry benchmark for projectors in its size and
performance category. Featuring high resolution DLP technology, high performance optics
and lenses, updated signal processing and built-in frame-lock synchronisation makes it the
ideal projector for multi-channel visualisation and simulation applications, where realism
and reliability are key criteria. In addition the excellent image performance, the 1080p and
WUXGA version are capable of Active Stereo 3D.
1.2 Features
• 1080p (1920x1080), WUXGA (1920 x 1200), panorama (2560x1080) or WQXGA (2560 x
1600) resolution single chip DLP® technology
• Patented Dual Architecture or LED illumination system and optics
• RealColor advanced colour management suite
• Fail safe, hot swap Dual Lamp architecture or longlife LED illumination
• Dual optomechanical IRIS for customizable brightness and contrast
• Full powered horizontal and vertical lens shift, allows direct stacking
• Full 12-bit colour resolution for minimised artefacting and high accuracy
• BrilliantColor™ technology with six-colour processing for accurate colours
• Elevated contrast levels for unmatched image dynamics
• High brightness for large screen applications
• Range of application specific colour wheel options
• Wide range of projection lenses
• Highly versatile colour management and calibration options
• Built-in real time clock for timed operations
• Sigma Designs™ technology video de-interlacing and processing
• Economy mode for reduced power consumption and prolonged lamp life
• Small and ergonomic footprint, with low weight
• Direct view status monitor and lamp function indicators
• Multiple video and graphics inputs for virtually any video and data source
• Dual Link DVI (330 MHz)
• HDMI ver. 1.3a
• LAN and RS232 for control and monitoring
CR series
User Manual - Introduction
6
WARNING: Used to point out potential danger to people or equipment when using this
product or peripheral equipment.
NOTE: Used to point out essential handling requirements for the projector, which if not
acted on may cause product malfunctioning.
TIP: Used to give advice which benefits the projector usage or conditions related to
projector performance.
The specifications and functionality of this projector may change without prior notice
7
english
Symbols used in this documentation
english
CR series
User Manual - Introduction
8
This device complies with safety regulations for Information Technology Equipment for use
in an office environment. Before using the device for the first time, please read the safety
instructions thoroughly.
2.3 SAFETY
This user guide contains important information about safety precautions and the set-up and
use of the projector. Please read the manual carefully before you operate the projector.
2.4 GENERAL WARNINGS
Use only the cables and cords supplied with the projector or original replacement cables.
Using other cables or cords may lead to malfunction and permanent damage of the unit.
Always use 3-prong / grounded power cord to ensure proper grounding of the unit. Never
use 2-prong power cords, as this is dangerous and could lead to electrical shock.
Never open the unit. The projector contains no user serviceable parts. Refer all repairs to
qualified personnel only. Make sure that no objects enter into the vents and openings of the
set.
Do not spill any liquids on the projector or into the vents or openings of the unit.
Always remove lens cap before switching on the projector. If the lens cap is not removed,
it may melt due to the high energy light emitted through the lens. Melting the lens cap may
permanently damage the surface of the projection lens.
Do not look into the projection lens when the projector is switched on. The strong light may
permanently damage sight. Do not look into the laser beam when activated on the remote
control. Laser light may permanently damage sight.
Do not point laser beam at people or animals.
Only place the projector on a stable surface, or mount it securely using an approved ceilingmount.
Do not drop the projector.
Always operate the projector according to the rotation guidelines. Operating the unit
in other positions may reduce lamp life significantly, and may lead to overheating,
resulting in malfunctioning.
Always allow ample airflow through the projector. Never block any of the air vents. Never
cover the unit in any way while running. Allow for sufficient distance to walls and ceilings to
avoid overheating.
Minimum safety distance to any side of the unit is 50 cm / 20” in any direction.
Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat nearer
than 50cm / 20” to the exhaust vent.
The projector is designed for indoor use only. Never operate the unit outdoors.
Do not operate the projector outside its temperature and humidity specifications, as this may
result in overheating and malfunctioning.
9
Connecting sources to a powered projector may result in product failure. It is recommended that the power cable connector (projector-end) or the mains power socket
are accessible while the product is in use to enable mains power to be disconnected
or switched off when connecting source devices. This should be considered during
product installation.
english
2 Safety Instructions
english
Only connect the projector to signal sources and voltages as described in the technical
specification. Connecting to unspecified signal sources or voltages may lead to malfunction
and permanent damage of the unit.
In order to prevent damage to the projector caused by overvoltages (e.g. lightning), we recommend connection to a line (mains) circuit which has overvoltage protection.
Allow lamp to cool down before changing. One lamp may be changed while the other lamp
is operating (hot-swap). USE ONLY ORIGINAL LAMPS.
2.4.1 INFORMATION AND WARNING ABOUT POTENTIAL HEALTH ISSUES RELATED
TO MERCURY VAPOR (UHP lamps only)
This projector uses a very powerful UHP™ lamp for illumination to produce an extremely
bright image.
This technology is similar to other high-pressure discharge lamps that are extensively used in
cars, street lights and other lighting appliances today. These lamps, like fluorescent lighting,
contain small amounts of mercury. The amount of mercury present in a lamp is far below the
limits of danger. It is very important that lamps containing mercury are treated properly to
minimize potential health hazards.
The UHP™ lamp, like any other high brightness projector lamp, is under high-pressure when
operating. While the lamp and the projector are carefully designed to minimize the probability of lamp rupture, the lamp may break while operating and small amounts of mercury
vapor may be emitted from the projector. The probability of rupture increases when the lamp
reaches its expected lifetime. It is therefore highly recommended that the lamp is replaced
when the rated lifetime is reached.
As a general precaution, secure good ventilation in the room when operating the projector. If
lamp rupture occurs, evacuate the room and secure good ventilation. Children and pregnant
women in particular should leave the room.
When replacing a worn lamp, dispose of the used lamp carefully by proper recycling.
Mercury is a naturally occurring, stable metallic element that may pose a safety risk to people
under certain conditions. According to the Public Health Statement for Mercury published by
the Agency for Toxic Substances and Disease Registry (“ATSDR”, part of the United States
Public Health Service), the brain, central nervous system and kidneys are sensitive to the
effects of mercury, and permanent damage can occur at sufficiently high levels of exposure.
Acute exposure to high concentrations of mercury vapor can cause conditions such as
lung and airway irritation, tightness in the chest, a burning sensation in the lungs, coughing,
nausea, vomiting and diarrhea. Children and fetuses are particularly sensitive to the harmful
effects of metallic mercury to the nervous system.
Seek medical attention if any of the above symptoms are experienced or if other unusual
conditions are experienced following lamp rupture.
2.4.2 HEAVY DUTY AND CONTINOUS USE (UHP lamps only)
The projector contains moving parts (such as cooling fans) that have limited life-expectancies. When the projector has been used for 8 000 hours, and when the unit is used in
mission-critical applications, it is recommended that the projector is given preventive maintenance by a qualified service person. A message will appear on the screen when the projector
is due for preventive maintenance. This will help ensure long term stable operation.
2.4.3 SERVICE PERSONNEL INFORMATION WARNING (UHP lamps only)
Use UV radiation eyes and skin protection during servicing.
CR series
User’s
Guide - Safety Instructions
User Manual - Safety Instructions
10
Laser radiation class II product; wavelength 670nm; maximum output 1mW.
Remote control complies with applicable requirements of 21 CFR 1040.10 and 1040.11.
Remote control complies with applicable requirements of EN/IEC 60825-1/2007
Use of controls or adjustments, or performance of procedures other than those
specified in the User Guide, may result in hazardous radiation exposure.
2.4.5 WARNING SYMBOLS
Here is a list of warning symbols found on the product lable(s):
READ USER GUIDE Attention! Read the user guide for further information!
DANGEROUS VOLTAGE Danger! High voltage inside the product!
HOT Warning! Hot surfaces!
WAIT Warning! Wait until cooled down!
MERCURY Warning! Lamp contains mercury! Recycle properly,
do not dispose of in ordinary waste!
UV Warning! UV radiation inside the product!
RECYCLE Warning! Recycle properly, do not dispose of in ordinary waste!
2.5 FCC
FCC regulations provide that changes or modifications not expressly approved by the party
responsible manufacturer could void your authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
CANADA
This Class A digital apparatus complies with Canadian ICES-003. / Cet appareil numérique
de la classe A est conforme à la norme NMB- 003 du Canada.
WARNING
This is a Class A product. In a domestic environment this product may cause radio
interference, in which case the user may be required to take adequate measures.
11
english
2.4.4 REMOTE CONTROL WARNING
english
2.6 WEEE INFORMATION
This product conforms to all requirements of the EU Directive on waste electrical and electronic equipment (WEEE). This product shall be recycled properly. It can be disassembled to
facilitate proper recycling of it’s individual parts. This product is using projection lamps that
shall be recycled properly. Consult your dealer or relevant public authority regarding drop-off
points for collection of WEEE.
2.6.1 Turkey RoHS compliance
Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur.
(Republic of Turkey: In conformety with the EEE Regulation)
2.7 ENVIRONMENTAL INFORMATION
2.7.1 Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2002/96/EC governing waste from electrical and electronic equipment, this product must not be disposed of
with other municipal waste. Please dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic equipment. To
prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or
your municipal waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee
2.7.2 Disposal of batteries in the product
This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately from municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium
(Cd), these chemical symbols will appear below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to ensure proper disposal
and to prevent potential negative effects on the environment and human health.
2.8 SERVICE INFORMATION
This product contains no user serviceable parts. If the product fails to function as expected,
please first check that all connections are properly made, and that the power cord is properly
connected. Please check that the projector as well as the video and computer sources are all
switched on. Cables and cords may break over time. Try to change cables and cords, in case
there is a bad or intermittent connection. Check if the circuit breaker or fuse of your mains
is intact. In the event of product failure, please contact your reseller. You should prepare a
description of the symptoms of failure you experience. Please also state product number and
serial number as printed on the label on the bottom of the projector.
CR series
User’s
Guide - Safety Instructions
User Manual - Safety Instructions
12
english
13
The following components are standard delivery:
Projector
Power Cable (Country Dependent)
Remote Control
User Documentation
Additional accessories available for the projector:
DVI-cable
Please verify that you have all compoents upon unpacking the unit, and its contents. Check
next page for additional accessories.
Please save packaging materials for future use, should it be necessary to ship the unit.
15
english
3 What’s in the box?
english
CR
Userseries
Manual - What’s in the Box?
User Manual - What’s in the box?
16
english
4 Getting to know the projector
4.1 Overview
ALens
B IR sensor
C1Ventilation - Air flow IN
C2Ventilation - Air flow OUT
D Lens release
E Power connector
FKeypad
B
G Connector panel
HLCD
Lamp lids*
I
J Adjustable feet
K Security lock
B
C
A
D
C1
L Ceiling mount
C1
E
Figure 4-1. - Projector front view
F
B
G
H
C2
B
I *
Figure 4-2. - Projector rear view
J
L
J
K
B
* Features in the user guide pictures/drawings may be
different from your projector depending on model/version.
Figure 4-3. - Projector bottom view
17
english
4.2 Indicators
System status indicators are located right of the keypad on the back of the projector. Figure
4-4 shows the three status indicators – one for each lamp and one for the system status.
* Pictures show backpanel of projector with UHP lamps.
LED illumination projectors have one indicator lamp (LED), instead of two (LAMP 1, LAMP 2).
Figure 4-4. The lamp indicators
For the lamp indicators the following apply:
-
PERMANENT GREEN LIGHT: The lamp is on and operating normally.
-
PERMANENT YELLOW LIGHT: The lamp is off. The lamp may be disabled in the menu or
the system is in standby.
-
PERMANENT RED LIGHT: Lamp life has expired, lamp is not igniting or lamp door is
open. If the lamp life has expired, please change projection lamp immediately. Failing to
change lamp may lead to lamp explosion. Please replace with original projectiondesign
replacement lamp.
-
FLASHING YELLOW LIGHT: The lamp is cooling down. The total cooling down time is
approx. 45 seconds.
-
NO LIGHT: No lamp inserted.
The replacement lamps must be purchased from an authorized projectiondesign dealer
for the warranty of the product to be valid. Using lamps from any other after market
supplier will void the warranty.
4.2.1 The status indicator
-
PERMANENT GREEN LIGHT: The projector is turned on and in normal operation.
-
PERMANENT YELLOW LIGHT: The projector is in standby mode. If the projector was
powered off by the power saving feature (DPMS), it will automatically power on when you
connect a valid source.
-
FLASHING YELLOW LIGHT: Please wait. The yellow light will flash a period after power
cord is connected (20-30 sec.), and a period after going to standby mode while lamp is
cooling down (approximately 45 sec.). The projector may not be turned on again until the
light has turned to permanent yellow.
-
FLASHING RED LIGHT: Projector is overheated. Turn off immediately! Check if air inlets
are covered or if ambient temperature is outside specifications. The projector cannot be
restarted until the power cord is disconnected and reconnected again. If the projector
continues to flash red, you will need to return the unit for service.
CR
series
User’s
Guide – Getting to know the projector
User Manual - Getting to know the projector
18
The projector has an illuminated keypad on the back of the unit. Figure 4-5 shows the
keypad.
Figure 4-5. Projector keypad
The keypad is used to:
* Pictures show backpanel of projector with UHP lamps.
LED illumination projectors have one indicator lamp (LED), instead of two (LAMP 1, LAMP 2).
- navigate the menu system
- scroll the information in the LCD panel
- directly select input sources
- enter pin code (if enabled)
- power on/off
- adjust basic image functions
The keypad is illuminated for operation in dark environments. Available functions are
illuminated in yellow while selected (active) functions are illuminated in green. Functions that
are not available are not illuminated.
4.2.3 Remote control
The remote control allows flexible access to the projector settings, either through direct keys,
or through the menu system. The remote control is backlit for use in dark environments.
It also has a data-jack that allows for wired connection to the projector. When the wire is
connected, the IR (infra-red) beam and internal batteries are switched off.
The direct sources buttons for VGA1, VGA2, X-Port 2 and YPbPr are not
available for all versions of the product. If your product does not have these inputs
implemented the OSD will display “not available” when pressing these buttons.
Do not look into the laser beam when activated on the remote
control. Laser light may permanently damage eyesight. Avoid
pointing the laser beam at people or animals.
Only use the supplied remote control, otherwise the result may
be malfunction.
Figure 4-6. Remote control
19
english
4.2.2 Keypad
english
4.3 Connectivity
he projector features a wide range of video inputs and command/control connectors.
Figure 4-7 shows the connector panel.
A
D
H
E
J
F
B
C
G
K
L
M
I
Figure 4-7. Connector panel
A
LAN: 10/100 Mbit Ethernet connector for command, control and software upgrade.
B
RC INPUT: 3.5mm mini-jack connector. Allows connection of external IR receiver or
wired remote control.
C
TRIGGERS: 3.5mm mini-jack connector triggers. Used for controlling peripheral
equipment like motorized screens.
D
3D SYNC: For 1080/WUXGA 3D projectors used to attach external ir-glass emitters
E
RS-232: Allows for wired remote control and monitoring of many projector functions
used in installation environments.
F
USB-A: Allows for software upgrades using a standard USB memory stick.
G
USB-B: Reserved for future use.
H
SYNC-IN: Allows for taking an external vertical sync signal and using that with the select
video input. This is mainly used in multiple projector installations with requirement of
video synchronization between the units.
I
SYNC-OUT: Constantly outputs the vertical sync signal of the active video input. This
is mainly used in multiple projector installations with requirement of synchronization
between the units.
J
DVI-D: Two Dual Link DVI-D connectors with bandwidth up to 330 Mhz total. These
connectors can also be used to form one uniform image by feeding half of the image
into each connector. HDCP compliant for sources up 165 Mhz.
K
VGA: Two VGA connectors with bandwidth up to 170 Mhz
L
YPbPr: Analog video input supporting YPbPr and RGB (sync-on-green) video standard
up to 1080i.
M HDMI 1.3: Two HDMI 1.3a connectors with bandwidth up to 165 Mhz each. These
connectors can also be used to form one uniform image by feeding half of the image
into each connector. HDCP compliant. All video formats specified by the HDMI 1.3a are
supported.
CR
series
User’s
Guide – Getting to know the projector
User Manual - Getting to know the projector
20
The projector has an easy-to-use on screen display (OSD) system for controlling the
extensive number of features implemented. Figure 4-8. Top level OSD menu, shows the top
level of the OSD menu.
Figure 4-8. Top level OSD menu
Activate the menu by pressing the “MENU” button on either the keypad or the remote
control. Navigate the menu using the arrow keys.
The various functions in OSD menu is described in Chapter “5 Basic setup”.
The top level menu item 3D is only visible for Active Stereo 3D enabled
projectors (1080p and WUXGA).
21
english
4.4 Graphical User Interface (GUI)
english
CR
series
User’s
Guide – Getting to know the projector
User Manual - Getting to know the projector
22
english
5 Basic setup
5.1 Lens
5.1.1 Lens and lens mount
A range of fixed and zoom lenses is available to cover most applications, both both for front
and rear projection. The lenses are powered and fitted with a bayonet mount for ease of
installation.
Switch off all equipment before setting-up for proper function.
When mounting and changing lenses, be aware that the optical system is exposed to dust
and foreign particles as long as the lens is not attached to the system. Do not leave the lens
mount open longer than necessary to change lens. If a lens is not mounted, always insert the
protection lid to avoid dust and foreign particles entering the internal optics.
Never run the projector without lens mounted.
5.1.2 Inserting a lens
A
To insert a lens please follow this procedure:
A Remove the protection lid from the bayonet mount by
turning the knob anti-clockwise.
B Remove the rear lens cap.
C Attach the projection lens using the bayonet mount,
observing the red insertion marks.
D Turn the lens firmly clockwise until it stops with a click.
B
E Remove the lens cap from the projection lens. If you
switch the projector on with the lens cap in place, the
lens cap may melt, damaging not only the lens cap,
but also the projection lens and surrounding parts.
5.1.3 Replacing a lens
C
To replace a lens please follow this procedure:
A
B
To change lens, first remove the current lens by
pushing the release button and twisting the lens
counter-clockwise until it comes loose. Pull the lens
out.
D
Insert the new lens as described in above.
E
F
23
english
5.2 Adjusting on screen image size and position
Adjusting the placement of the image on screen can be done using the:
1. Adjustable feet (E in Figure 5-1).
2. Lens shift mechanism controlled from the keypad, the remote control, RS-232 or LAN (A
in Figure 9).
3. Zoom (for lenses with zoom) in the lens controlled from the keypad, the remote control,
RS-232 or LAN (B in Figure 5-1).
After the correct image size and position is found, please adjust the image focus using the
keypad, the remote control, RS-232 or LAN. (C in Figure 5-1).
E
B
A
C
Figure 5-1. Image size ans position adjustment
5.3 Lamp operation
The projector is fitted with two individual projection lamps* that can be run in various modes.
In addition, lamps can be replaced as needed separately. This ensures an optimized cost of
ownership. Individual lamp timers are maintained for each lamp.
Lamp operation mode is controlled in the INSTALLATION > LAMPS sub menu.
* UHP lamp projectors only. LED projectors have only one lamp.
CR series
User
Manual - Basic setup
User Manual - Basic setup
24
Always operate the projector horizontally, within the range of the adjustable front and rear
feet. The projector may be rotated so that the lens points downwards. It may not be rotated
around the through-the-lens axis.
Operating the unit in other positions may reduce lamp life significantly, and may lead
to overheating, finally resulting in malfunctioning.
5.5 Ceiling mount
The projector can be ceiling mounted using an approved UL tested/ listed ceiling mount
fixture, with a capacity of minimum 60 kg / 130 lbs. For ceiling mount use M6 screws that
penetrate maximum 15 mm / 0.6” into the projector body. Figure 5-2. Ceiling mount, gives
detailed information about the alignment of the ceiling mount screw holes in the
projector.
For proper ventilation the minimum distance from ceiling/ rear wall should be:
30/ 50 cm, 12/ 20 inch.
59,5
53
95
82,5
15,5
94,3
111,8
384,9
95
82,5
59,5
53
Ceiling Mount Interface
M6 Threads
384,9
510
123,1
300mm
15,5
94,3
111,8
163,3
233
500mm
Ceiling Mount Interface
M6 Threads
500mm
Ceiling Mount Interface
M6 Threads
123,1
15,5
94,3
111,8
163,3
384,9
25
Figure 5-2. Ceiling mount
510
500mm
163,3
300mm
300mm
123,1
233
510
english
5.4 Projector rotation
english
5.5.1 Ceiling mount cover (optional)
The optional auxiliary cable cover can be mounted on the projector to conceal the interface
cables and power cord when the unit is ceiling mounted. Connect all cables and fix them in
place before the cable cover is attached to the projector. Figure 5-3 shows the ceiling mount
cover.
Figure 5-3. The ceiling mount cover
5.5.2 Attaching the ceiling cover
To attach the ceiling mount cover, please follow this procedure:
A Attach the cable cover to the projector by inserting the horizontal hooks on the cover in
the horizontal slots on the rear of the projector.
B Turn the cover until the vertical hooks on the cover are inserted into the vertical slots on
the rear of the projector.
C The cover will snap in place, to release pull the vertical hooks on the cover out of the
slots, letting the cover hinge on the horizontal hooks.
A
B
C
CR series
User
Manual - Basic setup
User Manual - Basic setup
26
Before setting up, switch off all equipment and disconnect the power cord. In order to
prevent damage to the projector caused by overvoltages (e.g. lightning), connect to a
line (mains) circuit which has overvoltage protection when installing.
5.6.1 Setting up a video source
For best quality video, connect a digital video source using the HDMI 1.3a interface (O) Connecting a video source in Figure 5-4. The HDMI input is HDCP copy protection compliant.
Depending on cable quality, the projector is supporting the use of cables with lengths up 20
meters (65 feet).
Figure 5-4. Connecting a video source
5.6.2 Setting up a computer source
The projector may be connected to up to six computer sources simultaneously, using the
HDMI (O), DVI-D (J) or VGA (K) interfaces, shown in Figure 5-4/Figure 5-5. The digital interfaces (DVI/HDMI) will yield a projected image with very low noise.
Both DVI and HDMI are HDCP compliant with sources up to [email protected] (single link
source up to 165 Mhz). Additional functionality may be acchieved using additional X-PORT
connectors like 3G-SDI, DisplayPort 1.1a and HDMI 3D (se separate sections).
Figure 5-5. Connecting a computer source
HDCP is not supported on higher resolution sources like [email protected] (WQXGA).
Connect the power cord after the other cables have been inserted properly.
5.6.3 Connecting command and control interfaces
The projector is supporting RS-232 and LAN command and control interfaces. Use the ASCII
based protocol to communicate with the projector. A detailed description of the ASCII protocol is available for download at www.projectiondesign.com.Connect the power cord after the
command and control cables are inserted properly.
Figure 5-6. Connecting command interfaces
27
english
5.6 Connection and cables
english
5.6.4 Attaching X-PORT™ modules
X-PORT™ modules are separately available for purchase and not included
with the base projector.
Switch off projector and disconnect power cord before attaching X-PORT™ module.
Before attaching any X-PORT module, please make sure you have the latest SW running on the projector. Please go to www.projectiondesign.com to download the current
SW and update the projector accordingly. See chapter 8 for details on how to upgrade
the projector SW.
The projector supports up to two X-PORT™ modules simultaneously:
- X-PORT™ 1 for additional image processing (X-PORT™ DCC120*). Left hand side.
- X-PORT™ 2 for additional connectivity (X-PORT™ 3G-SDI, X-PORT™ DisplayPort 1.1a
and X-PORT™ HDMI 3D*). Right hand side.
*X-PORT™ modules subject to availability.
To attach an X-PORT™ module, please follow this procedure:
A Remove cover plate, by removing the four screws.
B Attach module. Observe X-PORT™ 1 and 2 positions are different. Attaching X-PORT™
modules in the wrong position will leave the module non-functional, but it is not
destructive.
C Fix the four mounting screws securely.
A
Remove 4
retainer screws
B
Mount X-PORT module
Fasten 4
module
screws
C
*
Features in the user guide pictures/drawings may be different from your projector depending on model/version.
Finally connect power cord and switch on projector.
The first time after a module is attached, the projector will automatically update and
configure the module. This may take a few minutes. Please ensure that power
remains on during this period.
CR series
User
Manual - Basic setup
User Manual - Basic setup
28
X-PORT™ modules allows for extra functionality with the projector. This includes more connectivity as well as additional image processing.
Functionality may include extended connectivity (like 3G-SDI and HDMI 3D) and additional 3D
format support (like Blu-Ray frame packed, dual input sources, double flash 3D etc.)
Please refer to Chapter 6.4 for information on multi channel 3D sync.
5.7.1 X-PORT DCC120
X-PORT DCC120 is an X-PORT 1 module (post processing) adding additional 3D capabilities
and multi-projector synchronization capabilities to the system.
5.7.1.1 3D formats supported
By using X-PORT DCC120 the following 3D format will then be supported:
Dual head input:When “Dual head” is enabled, the projector will combine the signals from
DVI1 and DVI2 (or HDMI1 and HDMI2), place them beside each other and interpret it as a
single source. The two sources need to have the same resolution. For example, if both inputs
are 1920x1200 @ 60Hz, the combined dual head source will be seen by the projector as a
single 3840x1200 @ 60Hz source. If, now, 3D mode is set to side-by-side, the projector will
take the left half of this combined image, which is in fact the source on DVI1, and use it as
the left eye source. The same goes for DVI2 being the right eye source.
Side-by-side: In side-by-side 3D, each input frame is divided in half and the left half of the
frame is used as the left eye frame and the right half of the input frame is used as the right
eye frame. This makes the output width become half of the input width. If, for example, the
input is 1920x1200 @ 60Hz, the output will be 960 x 1200 @ 120Hz.
Frame sequential: n frame sequential 3D, every other frame is interpreted as the left eye
frame and the other input frame is interpreted as the right eye frame. To ensure that the
projector chooses the correct frames as the left eye and right eye frames, a 3D sync signal
should be connected from the IG’s display adapter DIN connector to the projector’s BNC
sync-in connector. If such a signal isn’t present, the projector will choose the first input frame
as the left eye frame and the next input frame as the right eye frame. This will be wrong half
the times the signal is acquired.
29
english
5.7 Using X-PORT™ modules
english
5.7.2 X-PORT 3G-SDI
The X-PORT 3G-SDI module is an X-PORT2 interface module to support all SDI, HD-SDI and
3G-SDI formats.
5.7.2.1 Connectivity
PARAMETER
VALUE
Main connectors
2xBNC-F
Input A1, Input B1
Redundancy connectors
2xBNC-F
Input A2, Input B2
Video formats
- SDI (SMPTE 259M, up to 360 Mbps)
- HD-SDI (SMPTE 292M, up to 1.485 Gbps)
- 3G-SDI (SMPTE 424M/425M, up to 3.0 Gbps)
Nominal impedance
75 Ohms
Scan format
Interlaced or progressive
Return loss
<-15 dB, DC @ 1 MHz to 1.5 GHz
Clock rate
Up to 3 Gbit/s (3G-SDI)
Maximum resolution
[email protected]
5.7.2.2 Cable Lenghts
PARAMETER
VALUE
3G-SDI
Max 100 m (RG-5 18 AWG/1694A)
HD-SDI
Max 110 m (RG-5 18 AWG/1694A)
SDI
Max 400 m (RG-5 18 AWG/1694A)
5.7.3 X-PORT HDMI 3D
The X-PORT HDMI 3D module is an X-PORT2 interface module to support various 3D formats from the HDMI 3D specification.
5.7.3.1 Connectivity
PARAMETER
VALUE
Main connectors
2xHDMI Type A
Input A, Input B
Video formats
720p or 1080p
Scan format
Progressive only
Clock rate
Up to 225 MHz
Maximum resolution
[email protected]
5.7.3.2 3D modes supported
CR series
User
Manual - Basic setup
User Manual - Basic setup
RESOLUTION
REFRESH
HDMI 3D MODE
1080p
60Hz, 50 Hz
Side by side, Top/Bottom
1080p
24 Hz
Side by side, Top/Bottom, Frame packed
720p
60Hz, 50 Hz, 24 Hz
Side by side, Top/Bottom, Frame packed
30
For easier alignment of the projector, test images are built into the system.
To enable test images, go to the menu entry INSTALLATION > TEST IMAGE. Cycle the various test images using the arrow keys. When a test image matching the aspect ratio of your
screen has been found, use the zoom, focus, lens shift and physical projector alignment to
match the screen.
5.9 Setting image orientation
In relation to the screen, the projector supports the following installation orientations:
• Desktop front (default)
• Ceiling front
• Desktop rear
• Ceiling rear
To set the image orientation go to menu entry INSTALLATION > IMAGE ORIENTATION
5.10 Using source scan
The projector can automatically scan through all the input connectors for a valid signal. If a
valid signal is found, the image will set up. This is called source scan.
Source scan is default disabled. When disabled, the projector will only search the selected input connector for a valid signal. Use the keypad, remote control or any command and control
interface to change in selected input interface.
To set the source scan setting, go to menu entry INSTALLATION > SOURCE SCAN
5.11 Limiting OSD messages
When detecting sources and using the various features of the projector, OSD messages will
appear on the screen. Which messages that are appearing can be partially controlled by the
user. The OSD can run in these modes:
• ON. All messages, warning and information OSDs are displayed.
• OFF. No messages are shown.
• Only warnings. Only critical warning messages like temperature overheating will be shown.
Go to menu entry INSTALLATION > OSD ENABLE to control the OSD behavior.
31
english
5.8 Image alignment
english
5.12 Changing the language of the menu system
The projector menu system has a total of 11 user-selectable languages embedded for easier
use all over the world. The default language is English.
The available languages are:
• English
• French
• German
• Spanish
• Russian
• Norwegian
• Swedish
• Korean
• Japanese
• Chinese Simplified
• Chinese Traditional
•Portuguese
•Italian
To change the language of the menu system, just select “LANGUAGE” from the top menu
and select your desired language.
5.13 Identifying system status
For ease of use, the projector has a complete menu available for system status. It is easily
accessible from the top menu. From this menu the following information can be read:
• Part number
• Serial number
• The year/week the projector was manufactured
• Current software version
• Runtime and remaining time for both lamps
• Total number of operating hours
• All network information
• Current lens mounted
• Currently active source
5.13.1
Getting information about the active source
By selecting STATUS > SOURCE INFORMATION basic information about currently active
source is displayed.
If a deeper analysis is required for the currently active source, select STATUS > SOURCE INFORMATION > ADVANCED. This menu provides detailed timing information for the currently
active source.
5.14 Using the dual lamp system (UHP models only)
The projector is fitted with two individual projection lamps* that can be run in various modes.
CR series
User
Manual - Basic setup
User Manual - Basic setup
32
This is information is only applicable to the WUXGA and 1080p versions, not WQXGA.
The projector has support for AS3D. AS3D images require active shutter glasses to work. To
enable active stereo select 3D > 3D MODE. Enabling 3D mode will configure the projector for
the use with an active stereo source.
The only active stereo 3D format natively supported by the projector is sequential left/
right at a frequency between 100 and 120 Hz. Both DVI and HDMI connectors can be
used for sources up to 165 Mhz. For sources between 165 and 330 Mhz, only DVI dual
link is supported.
After enabling stereo mode, configure the glass type being used by selecting 3D > 3D
GLASSES TYPE. The follow glasses are support:
• DLP Link™
• IR
• IR high brightness (may cause crosstalk)
When using IR glasses it is important to configure the phase delay between the glasses
and actual image. This is done using 3D > 3D LOCK PHASE DELAY with values 0 and 179
degrees.
If left/right data channels are swapped there will be no 3D effect in the image, only parallel
distortion between the channels. This can be countered by enabling the 3D > SWAP EYES
feature.
User selectable Brilliant Color™ processing will be disable when 3D is enabled.
33
english
5.15 Configuring 3D (AS3D)
5.16 Image sizes
english
1920 x 1080 (1080)
Image width
de
Wi
)
5m
2)
e
gl
de
i
aW
An
tr
Ul
(
1
EN
0
9
.7
:1
.5
(0
.
-2
gle
An
:
.16
oom
eZ
ngl
eA
d
i
W
m
Zoo
dard
Stan
13)
(EN
0
1.6
.24
1
.32 :
0-2
) 1.6
1
(EN1
) 2.37
N14
oom (E
Tele Z
Long Tele
m)
15
)1
15
(EN
0-
1.
1(
- 3.79
)
15m
m
12.00
15.00
11.00
13.75
10.00
12.50
9.00
11.25
8.00
10.00
7.00
8,75
6.00
7.50
5.00
6.25
4.00
5.00
3.00
3.75
2.00
2.50
1.00
1.25
0
0
m)
15
2.0 -
1(
: 1 (2.0
)
- 30m
0 : 1 (4.0 –
6) 3.80 - 6.5
Zoom (EN1
.0 -
(1
:1
Screen diagonal
m
40 m)
Projection distance
Lens types and specifications may change without prior notice.
For correct lens information please refer to projectiondesign.com/products/lenses
CR series
User
Manual - Basic setup
User Manual - Basic setup
34
1920 x 1200 (WUXGA)
7.50
25
7.00
Screen diagonal
m
m
12.00
15.00
11.00
13.75
10.00
12.50
9.00
11.25
8.00
10.00
7.00
8,75
6.00
7.50
5.00
6.25
4.00
5.00
3.00
3.75
2.00
2.50
1.00
1.25
0
0
6.50
6.00
20
5.50
5.00
4.50
4.00
3.50
3.00
10
de
Wi
2.50
)
5m
2.00
79
1.50
1.00
e
id
aW
ltr
U
N
(E
:1
.5
(0
An
0
)1
15
(EN
oom
eZ
ngl
eA
d
i
W
13)
(EN
0-
(1.
m)
15
oom
Tele Z
.0 -
60
(1
:1
1.
4-
1.2
.32
0-2
) 1.6
N11
E
(
m
Zoo
dard
Stan
Long Tele
0.50
0.00
e
gl
An
.
)0
12
.
-2
gle
.16
:1
5m)
.0 - 1
: 1 (2
0 : 1 (4.0 –
6) 3.80 - 6.5
Zoom (EN1
m)
.0 - 30
9 : 1 (2
7 - 3.7
) 2.3
(EN14
)
15m
40 m)
Projection distance
35
english
Image width
2560 x 1600 (WQXGA) / 2560 x 1080 (panorama)
7.50
25
7.00
Screen diagonal
m
m
12.00
15.00
11.00
13.75
10.00
12.50
9.00
11.25
8.00
10.00
7.00
8,75
6.00
7.50
5.00
6.25
4.00
5.00
3.00
3.75
2.00
2.50
1.00
1.25
0
0
6.50
6.00
20
:1
(0
.7
-
7m
)
5.50
le
(E
N4
2
)0
.8
0
5.00
An
g
4.50
W
id
e
english
Image width
4.00
gle
An
1
(
1.5
e
Wid
2.00
.20
3) 1
10
2.50
oom
le Z
4
(EN
(
9:1
A
dard
Stan
1
.50 :
9-2
) 1.6
N41
(E
m
Zoo
1.00
0.50
0
)
- 15m
(1.5
.0 – 40
1 : 1 (2
.50 - 4.6
2
(EN44)
Zoom
Short
m)
- 15
- 1.6
ng
1.50
0.00
1:
1.2
r
Ult
3.50
3.00
ide
aW
)0
45
(EN
.80
)
0m
3
5-
m)
Projection distance
CR series
User
Manual - Basic setup
User Manual - Basic setup
36
6.1 Controlling multiple projectors with remote control ID (RCID)
The remote control can be operated either in ‘broadcast mode’, or ‘individual mode’. When
several projectors are in use in an installation, individual control may be convenient. Individual
control is available either by wired remote control, using the data-jack, or by using an individual number code. For individual control, first set the individual RC ID code using the projector
menu system, see the SETTINGS sub menu. Then, to select a specific projector to control,
first press the ‘*’ button in the lower keypad area, then the code as set in the target projector.
A code can be in the range ‘0’..’99’. ‘0’ is reserved for broadcast. To select another target,
repeat the process by pressing ‘*’ and a new code. To exit individual control, press ‘*’’*’ twice
or press ‘*’ and ‘0’.
6.2 Protecting the projector with a pin code
The projector may be controlled by a PIN (Personal Identification Number) code. The PIN
code is 4 digits, and if the PIN code is activated, you must enter the correct code to unlock
the projector. Factory set PIN (1234).
To activate, deactivate or change the PIN code, see the SETTINGS > PIN CODE sub menu.
If an incorrect PIN code is entered, you may try again two times.
If you fail three times in a row, a PUK (unlock) code is needed.
The PUK code is supplied with the product.
Entering the puk code correctly is the customers responsibility
If you also fail three times with the PUK code, the projector locks up permanently, and can
only be unlocked by a special service unlock code.
To access this code, you will need to contact your dealer or a service station. The service
unlock code will be generated based on a secure, encrypted number that is produced by the
projector itself. The projector will produce a new number every time.
To unlock the projector, proof of ownership must be provided by the customer
37
english
6 Advanced setup
english
6.3 Using dual head input
For extended flexibility to connect high resolution sources with a pixel clock over 165 MHz,
the projector is supporting a dual head input mode. In this mode the left and right half of the
image can be connected to the DVI 1/DVI 2 or HDMI 1/HDMI 2 interfaces respectively
(Figure 6-1).
To enable this mode, go to the menu INSTALLATION > DUAL HEAD SETUP. Side-by-side is
the only available option at this time.
1
2
Figure 6-1. Dual input mode
An example of this is feeding a WUXGA (1920 x1200) 120Hz source with 960 x 1200 120Hz source resolutions on each the DVI interfaces.
When enabling this mode, the EDID data on each of the DVI connectors will automatically be
changed from WUXGA (1920 x 1200) 120Hz to 960 x 1200 - 120Hz.
For the image to be displayed in this mode, the resolution must be exactly the same
on both connectors.
In this mode the two connected sources must have exactly the same timing. A drift in
timing between the inputs will result in a visible split in the center of image.
Some graphic cards have problems with detecting the change from single head to
dual head mode. If problems occur, disconnect both signal cables before enabling or
disabling the dual mode in the menu.
CR series
User
Manual - Advanced setup
User Manual - Advanced setup
38
X-PORT DCC120 has advanced capabilities for handling synchronization of multiple projectors in a 3D installation.
6.4.1 Synchronous frame sequential
A typical synchronous frame sequential 3D setup is shown in Figure 6-2.
Figure 6-2. Synchronous frame sequential 3D
In this case IGs are synchronized and 3D sync from the source is connected from the DIN
connector on the IG to the BNC sync-in connector. The source 3D sync is then sent to every
projector in the setup. See table below.
SETTING
PROJECTOR 1
PROJECTOR 2
3D
Frame sequential
Frame sequential
3D L/R sync
BNC sync-in
BNC sync-in
3D BNC sync-out signal
Pass through
Pass through
6.4.2 Asynchronous frame sequential
This mode is not supported.
39
english
6.4 Multi-channel 3D synchronization
english
6.4.3 Synchronous side-by-side
Figure 6-3 illustrates a typical synchronous side-by-side 3D setup.
Figure 6-3. Synchronous side-by-side setup
Since the sources are synchronized in this setup, synchronization management is not required in the projector. The table below shows the recommended system settings.
CR series
User
Manual - Advanced setup
User Manual - Advanced setup
SETTING
PROJECTOR 1
PROJECTOR 2
3D
Side-by-side
Side-by-side
3D L/R sync
Source
Source
3D BNC sync-out signal
Not used, but can be
set to 3D glass sync.
Not used, but can be
set to 3D glass sync.
40
In asynchronous side-by-side 3D, the projectors utilize the BNC sync-in and sync-out connectors to distribute a system wide display sync. This display sync is used by all projectors
to perform frame rate conversion on the input signals if necessary. Figure 6-4 illustrates this
setup.
Figure 6-4. Asynchronous side-by-side setup
As seen in Figure 6-4, an extra cable is connected between BNC sync-out on projector 1
and BNC sync-in on projector 2. In this setup the projectors need the settings in the table
below to send/utilize the display sync correctly.
41
SETTING
PROJECTOR 1
PROJECTOR 2
3D
Side-by-side
Side-by-side
3D L/R sync
Source
BNC sync-in
3D BNC sync-out signal
3D display L/R sync
Pass through
english
6.4.4 Asynchronous side-by-side
english
6.5 Setting custom color space and digital level
The projector will automatically try to set the correct color space and digital drive level based
on information from the source.
To manually override the automatically detected color space and digital level go to menu
entry PICTURE -> ADVANCED. Set the “digital color space and level” to manual and select
your color space and digital drive level.
6.6 Disabling IR receivers
The projector has 3 IR receivers as shown in chapter “4.1 Overview”.
These receivers can be individually disabled if necessary. Go to menu entry INSTALLATION >
IR FRONT / IR REAR to disable the receivers.
6.7 Controlling screens with triggers
The projector has two programmable triggers with 3.5 mm mini-jack connectors. These can
be used to enable or disable screens, curtains or other peripheral equipment.
To change trigger settings, go to menu entry INSTALLATION > TRIGGER
By default:
• Trigger 1 is set to control a screen depending on whether projector is powered on or not.
• Trigger 2 is set to control a screen depending on the aspect ratio of currently active
source.
Both triggers can be manually overridden both in the menu system and by using the command and control protocol through RS-232 or LAN.
6.8 Setting aspect trigger behavior
To customize the aspect trigger functionality, go to menu entry INSTALLATION > TRIGGER >
ASPECT TRIGGER BEHAVIOR. In this sub-menu it is selectable for which input aspect ratios
the trigger will be enabled.
6.9 Automatic power on/off
The projector can be automatically powered on or off by using the internal timer function or
DPMS.
6.9.1 Using the timer
The projector features a real-time clock that enables timing control. This means that the
projector can be programmed to switch on and off at certain pre-set times during a weekly
cycle.
To allow for a flexible schedule, 10 ‘programs’ are available. With each program, you can
define the switch on or switch off time for a single day (Monday to Sunday), all work days
(Monday through Friday), or week-end (Saturday and Sunday). One, several or all programs
can be active at the same time as desired. In this way, a flexible scheme can be established.
Observe the 24 hour time format. For more information, see the SETTINGS > TIMER menu.
The following example illustrates a case where the projector turns on at 08:00 in the morning
(8 am) and switches off at 20:00 (8 pm) on weekdays (Monday through Friday). Weekends
(Saturdays and Sundays), it turns on at 10:00 (10 am) and off at 18:00 (6 pm). VGA is used
as the source. For this, four programs are needed, 2 for on and two for off.
CR series
User
Manual - Advanced setup
User Manual - Advanced setup
42
Using DPMS (Display Power Management Signaling)
The projector is enabled for DPMS (Display Power Management Signaling). When enabled,
the projector will automatically switch to standby mode after a specified time if there is no
valid source present at its inputs. When a valid source is reconnected, the projector will start
up again.
To enable or disable DPMS, go to menu entry SETTINGS > DPMS. The desired DPMS timeout is set in the DPMS > DPMS TIMEOUT menu entry.
DPMS is disabled by default.
6.10 Disabling LED indicators
In certain installations it may desirable to completely disable the LED indicator in the keypad
of the projector. To disable the LED indicators, go to menu entry SETTINGS > LED
INDICATORS MUTE.
If the LED indicators are enabled, the timeout period can be set in the menu under SETTINGS > BACKLIGHT TIMEOUT.
6.11 Setting the background color
The background color displayed when the projector is searching for a source can be set to
a set of predefined colors. Go to menu entry SETTINGS > BACKGROUND to set the desired
color. Default is black. Setting OSD menu timeout
If the OSD menu is open and not used for a defined period of time, it will automatically be
disabled. The default time is 30 seconds. This timeout interval can be controlled from 5 seconds to 60 seconds. The timeout can also be set to “never” for the OSD menu to never time
out. Go to menu entry SETTINGS > MENU TIMEOUT to change this setting.
6.12 Selecting the startup logo
When the projector is starting up, a logo is displayed in the entire image. The logo can also
be set to “black” if it is desirable to disable the manufacturers default logo. Go to menu entry
SETTINGS > SPLASH to change this setting.
6.13 Setting OSD menu timeout
If the OSD menu is open and not used for a defined period of time, it will automatically be
disabled. The default time is 30 seconds. This timeout interval can be controlled from 5 seconds to 60 seconds. The timeout can also be set to “never” for the OSD menu to never time
out. Go to menu entry SETTINGS > MENU TIMEOUT to change this setting.
6.14 Selecting the startup logo
When the projector is starting up, a logo is displayed in the entire image. The logo can also
be set to “black” if it is desirable to disable the manufacturers default logo. Go to menu entry
SETTINGS > SPLASH to change this setting.
43
english
6.9.2 english
CR series
User
Manual - Advanced setup
User Manual - Advanced setup
44
The projector has power features for picture optimization. This chapter describes details in
using these features. All color calibration is done using projectiondesign’s proprietary RealColor™ solution.
7.1 Calibration data
All projectiondesign projectors are measured and calibrated with high precision equipment at
the factory for the best out-of-box experience. Over the lifetime of the lamps the characteristics of the projector might change slightly. The same applies when replacing lamps.
7.1.1 Updating RealColor™ calibration data
For accurate results with the RealColor™ system, accurate measurement data is required.
RealColor™ calibration data can be found under the menu entry PICTURE > CALIBRATION >
REALCOLOR CALIBRATION > MEASURED VALUES
X, Y and relative luminance values for red, green, blue, white and BrilliantColor™ 1 is entered
in this menu. The BrilliantColor™ should all be set to 0.000 for the VizSim (RGBRGB) color
wheel. All values can also be updated using the communications protocol over RS-232 or
LAN.
Before setting these values, it is important to select the desired BrilliantColor™
setting. Go to menu entry PICTURE > REALCOLOR > BRILLIANTCOLOR to select
the desired BrilliantColor™ look.
Measurements must be done on the built in test patterns. This is in particularly important for
the BrilliantColor™ 1 test pattern since it is impossible to generate this pattern correctly using
a computer source. In the user menu these patterns can be accessed through PICTURE >
CALIBRATION > REALCOLOR CALIBRATION > CALIBRATION TESTIMAGE. Use the arrow
keys to cycle through the images.
Performing a factory reset of the projector will restore the measured values to the
values measured in the factory.
When measuring data, a high quality measurement instrument is highly recommended
for accurate results. Spectrometers (like PhotoResearch PR-655) are preferred.
For an easier calibration procedure, automated calibration can be achieved using
projectiondesign’s software package ProNet. A license for the calibration software
package of ProNet must be purchased separately.
45
english
7 Optimising the picture
english
7.2 Working with RealColor™
7.2.1 Setting the BrilliantColor™ correctly
The BrilliantColor™ setting is used to control how color boost is applied in the image.
It can operate in four modes:
• Computer Native (Default): This give max brightness and color boost. Recommended
for non-video applications, like CAD and visualization.
• Computer Balanced: Gives the same brightness as Computer Native, but has a less
aggressive color boost profile.
• Video Native: Gives less brightness than computer, but will appear with significantly less
noise in video content.
• Video Balanced: Same brightness as Video Native, but with a smoother color boost
profile.
• Off: Only recommend for applications requiring a pure red, green, blue mix of colors.
No secondary color or white are added to the mix.
CR series
User
Manual – Optimising the picture
User Manual - Optimising the picture
46
The projector features a set of 6 built in gamma curves: Film 2.2, Film 2.8, Video 1, Video 2,
Computer 1, Computer 2. The different gamma curves are displayed below.
The names of the curves are descriptive for their recommended use. Use any of the
computer curves for video applications will results in significant image noise.
Figure 7-1. Film 2.2 gamma
Figure 7-2. Film 2.8 gamma
Figure 7-3. Video 1 gamma
47
english
7.2.2 Gamma
english
Figure 7-4. Video 2 gamma
Figure 7-5. Computer 1 gamma
Figure 7-6. Computer 2 gamma
CR series
User
Manual – Optimising the picture
User Manual - Optimising the picture
48
RealColor™ operating modes
Before any color correction is applied to the image, the feature must be enabled. Go to menu
entry PICTURE > REALCOLOR > COLOR CORRECTION to enable RealColor™.
RealColor™ can operate in 3 modes:
• Color temperature/white point correction only.
• Red, Green, Blue, White correction. In this mode optimal color coordinates for Cyan,
Magenta and Yellow will be computed automatically.
• Red, Green, Blue, Cyan, Magenta, Yellow, White. In this mode color points and intensity
for each color can be manipulated separately.
To change the RealColor™ mode, please go the menu entry PICTURE > REALCOLOR >
DESIRED VALUES > DESIRED COORDS MODE.
7.2.4 Setting a white point or color temperature
After enabling RealColor™, set the color temperature in the menu entry PICTURE > REALCOLOR > COLOR TEMPERATURE. Values between 3200K and 9300K can be selected.
These color temperatures are tracking the “black body curve”- the black curved line in the
center of CIE Chart in Figure 7-7. The default is the D65 illuminant at 6500K.
Figure 7-7. CIE Chart with the black body curve
The white point can also be set to a custom value defined by an x, y coordinate not linked
to the black body curve. Go to menu entry PICTURE > REALCOLOR > X-COORDINATE and
PICTURE > REALCOLOR > Y-COORDINATE to change the white point.
49
english
7.2.3 english
7.2.5 Defining the system color gamut
All colors visible to the eye are defined by CIE Chart in Figure 7-7. The boundary of the colors
the projector can display is called the system color gamut. The white triangle in Figure 7-7 is
an example of a system color gamut. By default the projector has the widest possible system
gamut, which is limited by the color wheel selected for the system. The VizSim color wheel
has the widest color gamut and the High Brightness color wheel has the smallest.
The system color gamut cannot be expanded outside color gamut defined by the
color wheel.
It may be desirable to change the system color gamut of the projector to:
- Color match multiple projectors.
- Meet defined color standards, like REC 709.
- Create a special “look” to the image.
Before the system color gamut can be change the desired RealColor™ mode has to be
defined. To change the RealColor™ mode, please go the menu entry PICTURE > REALCOLOR > DESIRED VALUES > DESIRED COORDS MODE.
RealColor™ has to be enabled for the desired system gamut to be applied. Go to menu entry
PICTURE > REALCOLOR > COLOR CORRECTION to enable RealColor™.
After RealColor™ is enabled and the desired color correction mode is selected, please go
the menu entry PICTURE > REALCOLOR > DESIRED VALUES to change the color points to
the your desired system color gamut.
For graphical visualization of the system color gamut and easy color management for
a single or multiple projectors, the ProNet software package could be used. A license
for the calibration software package of ProNet must be purchased separately.
CR series
User
Manual – Optimising the picture
User Manual - Optimising the picture
50
8.1 Software upgrades
In order to upgrade your projector, please follow the method and sequence described below.
• You will need a USB memory stick set up with a FAT-file system to perform this upgrade
• Access the upgrade software from the following web-address;
www.projectiondesign.com
•Download and save the firmware.zip-file to your PC desktop
• Unzip and extract the firmware file to the root of a memory stick
PS! Important that the USB is safely removed from computer, using the eject function on your PC.
• Set the projector in standby mode
• Insert the memory stick in the projector and wait for a few seconds
• The LCD display will indicate that it has detected an upgrade file on the memory stick.
Wait a few seconds while the file is validated
• Remove the memory stick when the LCD display instructs you to do so.
• Do not remove the power cord while the upgrade is still in progress
• The projector may restart several times during the upgrade
The upgrade has finished successfully when the ordinary LCD display returns.
P l e a s e re fe r to o u r we bsi te to downl o a d the re qui re d fi l e s o r se e k o the r i nfor mat ion
51
english
8 Maintenance
english
8.2 Lamp replacement (UHP units only)
The LAMP indicators on the keypad will turn red when lamp life expires or if the lamp fails.
Change the lamp when lifetime expires. Always replace lamp with the same type and rating.
USE ORIGINAL LAMPS ONLY.
The lamp includes an electronic lamp timer that is tracking the life time of the lamp.
Allow lamp to cool down before changing. One lamp may be changed while the other lamp is
operating (hot-swap).
Release the screw (LAMP 1) or (LAMP 2) depending on which lamp that needs to be replaced.
A
Be careful not to touch the protective glass when replacing the lamp,
this may cause the protective glass to overheat and break while in use.
Be extremely careful when removing the lamp module. In the unlikely
event that the bulb ruptures, small glass fragments may be generated.
The lamp module is designed to contain these fragments, but use
caution when removing the lamp module.
H
B
AOpen the lamp lid(s).
BTurn the three locking screws a quarter turn anti-clockwise.
CPull the lamp out.
DReplace with a new lamp in reverse order.
EInsert a new lamp. Observe the guide pins.
G
FTurn the tree locking screws a quarter turn clockwise.
GClose the lamp lid.
C
F
D
HTurn the locking screw clockwise.
In the unlikely event of a lamp rapture, a limited amount of mercury vapor
may be emitted into the room. To avoid inhailing this mercury vapor
(which is toxic, and can be harmful for lungs and nervous system) the
room should be thoroughly ventilated for a period of at least 30 minutes.
There are no known health hazards from exposure to lamps that are
intact and which are used within an enclosed fixture. No adverse effects
are expected from occational exposure to broken lamps. As a matter of
good practise, avoid prolonged or frequent exposure to lamps unless
there is adequate ventilation. The major hazard from broken lamps is the
possibility of sustaining glass cuts.
E
CR series
User
Manual - Maintenance
User Manual - Maintenance
52
9.1 Product details
technology
concept
available resolutions
connectivity
dimensions (dwh)
weight
environmental
power requirements
BTU/hr
operating temperature
conformances
UHP lamp
lamp life
lamp part no.
LED lamp
lamp life
lamp part no.
single chip DMD™ (Digital Micromirror Device™)
sealed, all-glass optical design with lens shift
WQXGA (2560 x 1600)
WUXGA (1920 x 1200)
1080p (1920 x 1080)
please refer to section 4.3 Connectivity for complete list
376 x 510 x 223 mm (ex. lens)
about 12.6 kg (ex. lens)
RoHS, WEEE
8.4A ~100-240V 50-60Hz
<1050W power consumption (UHP)
<325W power consuption (LED)
<2750 (UHP) / <1100 (LED)
0 – 40ºC / 32 – 104ºF, 0 – 1500 m
0 – 35ºC / 32 – 95ºF, 1500 – 3000 m
CE, FCC Class A and cCSAus
2 x 300W UHP™
2000/2500 hrs full/eco (5000 hrs in auto switch eco mode*)
400-0500-00
LED illumination
Up to 100000 hours (Full power)
Up to 100000 hours (Eco mode)
n/a
* Option in lamp sub menu: One lamp will be lit at the time and the projector will automatically switch between the lamps in
a specified interval (1hr to 24hr).
For a more extensive and up to date overview of technical specifications, please refer to the product page
on our home page.
53
english
9 Technical specifications
english
CR
Userseries
Guide - Technical specifications
User Manual - Technical specifications
54
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement