Craftsman | 315.265670 | Operator`s manual | Craftsman 315.265670 Operator`s manual

PERATOR'S
MANUAL
®
1/2 in. HAMMER DRILL
VARIABLE SPEED/REVERSIBLE
DOUBLE iNSULATED
Model No.
315.265670
A
WARNING:
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this product.
Customer
Help Line: 1=800=932=3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman
Visit the Craftsman web page: www.sears.com/craftsman
983000-853
08-17-06 (REV:02)
Save this manual
Estates, IL 60179 USA
for future
reference
[] Warranty............................................................................................................................................................
2
[] Introduction
........................................................................................................................................................
2
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
GeneralSafetyRules............................................................................................................................................
3-4
SpecificSafetyRules............................................................................................................................................
4
Symbols
.............................................................................................................................................................
5-6
Electrical
............................................................................................................................................................
7
Features
.............................................................................................................................................................
8-9
Assembly
...........................................................................................................................................................
9
Operation
...........................................................................................................................................................
10-14
Maintenance
.......................................................................................................................................................
14-15
Accessories
........................................................................................................................................................
15
Exploded
ViewandPartsList..................................................................................................................................
16
PartsOrdering/Service
....................................................................................................................................
BackPage
ONE-YEAR FULL WARRANTY
ON CRAFTSMAN
PROFESSIONAL
TOOL
If this Craftsman Professional tool fails to give complete satisfaction within one year from date of purchase, RETURN IT TO
ANY SEARS STORE OR PARTS AND REPAIR CENTER OR OTHER CRAFTSMAN OUTLET iN THE UNITED STATES
FOR FREE REPAIR.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
This tool has many features for making its use more pleasant and enjoyable. Safety, performance,
have been given top priority in the design of this product making it easy to maintain and operate.
and dependability
A
WARNING!
Read all instructions. Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury. The term "power
tool" in all of the warnings listed below refers to
your mains-operated (corded) power tool or batteryoperated (cordless) power tool.
SAVE THESE
WORK
INSTRUCTIONS
AREA SAFETY
[] Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
[] Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
[] Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
ELECTRICAL
SAFETY
[] Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
[] Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
[] Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk
of electric shock.
[] Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
[] When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
PERSONAL
SAFETY
[] Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
[] Use safety equipment. Always wear
Safety equipment such as dust mask,
shoes, hard hat, or hearing protection
priate conditions will reduce personal
eye protection.
non-skid safety
used for approinjuries.
[] Avoid accidental starting. Ensure the switch is in
the off-position
before plugging in. Carrying power
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
[] Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
[] Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
[] Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
[] if devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust-related hazards.
[] Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
[] Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
POWER
TOOL USE AND
CARE
[] Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
[] Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
[] Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
[] Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
[] Maintain power tools. Check for misalignment
or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
[] Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
[] Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended could
result in a hazardous situation.
SERVICE
[]
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
[] When servicing a power tool, use only identical replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury.
_1I_ WARNING!
To reduce the risk of injury, user must
read instruction manual.
[] Wear ear protectors with impact
noise can cause hearing loss.
drills. Exposure to
[] Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
[] Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
[] Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
[] Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the risk
of serious personal injury.
[] Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
[] Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule
will reduce the risk of serious personal injury.
[] Inspect tool cords periodically and, if damaged,
have repaired at your nearest Sears or other qualified service center. Constantly stay aware of cord
location. Following this rule will reduce the risk of
electric shock or fire.
A
[] Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized service center. Following this rule will reduce the risk of
shock, fire, or serious injury.
[] Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gauge size (A.W.G.) of at least 14 is
recommended for an extension cord 50 feet or less
in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the
cord. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
[] inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk
of serious personal injury.
[] Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instructions also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
Someofthefollowingsymbolsmaybeusedonthistool.Pleasestudythemandlearntheirmeaning.Properinterpretationofthesesymbolswillallowyouto operatethetoolbetterandsafer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
W
Watt
Power
min
Minutes
Time
"L,
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
n o
No Load Speed
Rotational speed, at no load
[]
Class II Construction
Double-insulated
.../min
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
@
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Read The Operator's Manual
To reduce the risk of injury, user must read and understand
operator's manual before using this product.
Eye Protection
Always wear safety goggles or safety glasses with side shields,
or a full face shield when operating this product.
Safety Alert
Precautions that involve your safety.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Hot Surface
To reduce the risk of injury or damage, avoid contact with any
hot surface.
0
@
@
@
®
construction
Thefollowingsignalwordsandmeanings
areintendedto explainthe levelsofriskassociated
withthis
product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION:
Indicates
a potentially
hazardous
result
in minor
or moderate
injury. situation, which, if not avoided, may
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service we suggest you return the
product to your nearest SEARS OR OTHER QUALIFIED
SERVICE CENTER for repair. When servicing, use only
identical replacement parts.
_
A
WARNING:
To avoid serious personal injury, do not
attempt to use this product until you read thoroughly
and understand completely the operator's manual.
Save this operator's manual and review frequently for
continuing safe operation and instructing others who
may use this product.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles, safety glasses with side shields, or a full face shield when needed. We recommend Wide
Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
Always use eye protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
DOUBLE
INSULATION
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are
isolated from the internal metal motor components with
protecting insulation. Double insulated tools do not need
to be grounded.
A
WARNING:
The double insulated system is
intended to protect the user from shock resulting
from a break in the tool's internal insulation. Observe
all normal safety precautions to avoid electrical
shock.
NOTE: Servicing of a tool with double insulation requires
extreme care and knowledge of the system and should
be performed only by a qualified service technician. For
service, we suggest you return the tool to your nearest
Sears or other qualified service center for repair. Always
use original factory replacement parts when servicing.
ELECTRICAL
CONNECTION
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz,
AO only (normal household current}. Do not operate
this tool on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the tool does not operate when plugged into an outlet,
double-check the power supply.
EXTENSION
CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An
undersized cord will cause a drop in line voltage, resulting
in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord.
Only round jacketed cords listed by Underwriter's Laboratories (UL) should be used.
When working outdoors with a tool, use an extension
cord that is designed for outside use. This type of cord is
designated with "WA" on the cord's jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
**Ampere rating
(on tool faceplate)
0-2.0
2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
16
16
16
16
14
14
50'
16
16
16
14
14
12
100'
16
16
14
12
10
--
**Used on 12 gauge - 20 amp circuit
NOTE: AWG = American Wire Gauge
A
A
WARNING:
Keep the extension cord clear of the
working area. Position the cord so that it will not get
caught on lumber, tools or other obstructions while
you are working with a power tool. Failure to do so
can result in serious personal injury.
WARNING:
Check extension cords before each
use. If damaged replace immediately. Never use tool
with a damaged cord since touching the damaged
area could cause electrical shock resulting in serious
injury.
PRODUCTSPECIFICATIONS
Chuck ..........................................................
1/2 in. Keyless
Switch ..........................................................................
No Load Speed ................................
VSR
0-1,000/O-2,700/min.
Input ................................ 120 V, 60 Hz, AC only, 7.5 Amps
Power Cord ................................................................
Net Weight ...............................................................
10 ft.
5.5 Ibs.
Blows Per Minute ........................ 0-19,000/O-46,000/BPM
LEVEL
DRILLING/HAMMER
MODESELECTOR
TWO-SPEED
GEARTRAIN
(HI-LO)
SPINDLELOCK
BUTTON
LOCK-ON
BUTTON
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
AUXILIARY
HANDLEASSEMBLY
KEYLESS
CHUCK
DEPTH
GAUGECLAMP
VARIABLESPEED
SWITCHTRIGGER
LIVE TOOL
INDICATOR
DEPTH
STOPROD
Fig. 1
KNOW YOUR
HAMMER
LEVEL
DRILL
See Figure 1.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
AUXILIARY
HANDLE
ASSEMBLY
A level is located on the top of the motor housing to help
you keep the drill bit level during use.
LIVE TOOL INDICATOR
Your drill is equipped with an auxiliary handle assembly for
ease of operation and to prevent loss of control.
The live tool indicator is located on the handle of the drill
and indicates that the tool is connected to a power
supply.
BLOWS
LOCK=ON
PER MINUTE
BUTTON
This tool features an impact speed of 0-19,000/0-46,000
BPM (Blows Per Minute). Blows Per Minute is the number
of impacts per minute.
The lock-on button is convenient for continuous
extended periods of time.
DEPTH
The spindle lock keeps the chuck from turning while
installing and removing bits.
STOP
ROD
A depth stop rod has been supplied with this product to
assist in controlling the depth of drilled holes.
DIRECTION
OF ROTATION
SELECTOR
(FORWARD/REVERSE)
Your drill has a direction of rotation (forward/reverse)
selector located above the variable speed switch trigger
for changing the direction of bit rotation.
KEYLESS
CHUCK
The keyless chuck allows you to hand-tighten
the drill bit in the chuck jaws.
or release
SPINDLE
VARIABLE
PACKING
LiST
Hammer Drill with Auxiliary Handle Assembly
Depth Stop Rod
Carrying Case
Operator's
Manual
SPEED
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with decreased trigger pressure.
WARNING:
If any parts are damaged or missing
do not operate this tool until the parts are replaced.
Failure to heed this warning could result in serious
personal injury.
A
[] Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
[] If any parts are damaged or missing, please call
1-800-932-3188 for assistance.
GEAR TRAIN
The two-speed gear train is designed for drilling or driving
at LO (1) or HI (2) speeds. A switch is located on the side
of your drill for selecting either LO (1) or Hi (2) speed.
This product has been shipped completely assembled.
[] Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
LOCK
TWO-SPEED
UNPACKING
[] Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list
are included.
drilling for
WARNING:
Do not attempt to modify this tool
or create accessories not recommended for use
with this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
A
WARNING:
Do not connect to power supply until
assembly is complete. Failure to comply could result
in accidental starting and possible serious injury.
A
WARNING:
Do not allow familiarity with tools
to make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
REVERSE
injury.
A
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating power
tools. Failure to do so could result in objects being
thrown into your eyes resulting in possible serious
injury.
SWITCH
TRIGGER
FORWARD
/
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
APPLiCATiONS
You may use this tool for the purposes listed below:
[] Hammer drilling in concrete, brick, or other masonry
[] Drilling in wood
Fig. 2
[] Drilling in ceramics, plastics, fiberglass, and laminates
KEYLESS
[] Drilling in metals
[] Mixing paint
VARIABLE
SPEED
SWITCH
The drill has a keyless chuck that makes it simple to
tighten or release drill bits in the chuck jaws. The arrows
on the chuck indicate which direction to rotate the chuck
body in order to LOCK (tighten) or UNLOCK (release) the
drill bit.
TRIGGER
See Figure 2.
To turn the drill ON, depress the variable speed switch
trigger. To turn it OFF, release the variable speed switch
trigger.
VARIABLE
A
SPEED
The variable speed switch delivers higher speed and
torque with increased trigger pressure and lower speed
with decreased trigger pressure.
NOTE: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a
normal part of the switch function.
DiRECTiON
CHUCK
See Figure 3.
OF ROTATION
WARNING;
Do not hold the chuck body with one
hand and use the power of the drill to tighten the
chuck jaws on the drill bit. The chuck body could slip
in your hand, or your hand could slip and come in
contact with the rotating drill bit. This could cause an
accident resulting in serious personal injury.
UNLOCK
(RELEASE)
SELECTOR
CHUCKJAWS
CHUCK
BODY
(FORWARD/REVERSE}
See Figure 2.
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the
drill held in normal operating position, the direction of
rotation selector should be positioned to the left of the
switch trigger for forward drilling. The drilling direction is
reversed when the selector is to the right of the switch
trigger.
DRILLBIT
CAUTION: To prevent gear damage, always allow
the chuck to come to a complete stop before changing the direction of rotation.
LOCK
(TIGHTEN)
To stop the drill, release the variable speed switch trigger
and allow the chuck to come to a complete stop.
NOTE: The drill will not run unless the direction of rotation
selector is pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause the drill to become overheated. If this occurs, cool
the drill by running it without a load and at full speed.
SPINDLE
LOCKBUTTON
Fig. 3
10
SPINDLELOCK
TW0-SPEED
GEARTRAIN(Hi-LO)
See Figure 3.
2-HI SPEED
[] To lock the spindle, depress and hold the spindle lock
button.
[] While keeping the button depressed, rotate the chuck
clockwise until the spindle clicks into a locked position
and will not rotate further.
)
[] To unlock, release the button.
NOTE: Always be sure the spindle lock button is released
and disengaged before turning the drill ON.
TWO-SPEED
See Figure 4.
GEAR TRAIN
The drill has a two-speed gear train designed for drilling or
driving at LO (1) or HI (2} speeds. A switch is located on
the side of the drill to select either LO (1) or HI (2) speed.
When using drill in the LO (1) speed range, speed will
decrease and unit will have more power and torque. When
using drill in the HI (2) speed range, speed will increase
and unit will have less power and torque. Use LO (1)
speed for high power and torque applications and HI (2)
speed for fast drilling or driving applications.
_IIL WARNING:
1-LO SPEED
Fig. 4
UNLOCK
(RELEASE)
CHUCKJAWS
CHUCK
BODY
Always unplug the tool when installing
or removing bits, adjusting settings, or when the tool
is not in use. Failure to unplug the tool may result in
accidental starting and serious personal injury.
INSTALLING
BITS
DRILLBIT
See Figure 5 - 6.
[] Unplug the drill.
LOCK
(TIGHTEN)
[] Lock the spindle.
[] Open or close the chuck
opening is slightly larger
use. Also, raise the front
bit from falling out of the
Insert the drill bit.
jaws to a point where the
than the bit size you intend to
of the drill slightly to keep the
chuck jaws.
SPINDLE
LOCKBUTTON
RIGHT
Fig. 5
WARNING:
Make sure to insert the drill bit straight
into the chuck jaws. Do not insert the drill bit into the
chuck jaws at an angle then tighten, as shown in
figure 6. This could cause the drill bit to be thrown
from the drill, resulting in possible serious personal
injury or damage to the chuck.
[] Tighten the chuck jaws securely on the bit.
NOTE: Rotate the chuck body in the direction of the
arrow marked LOCK to close the chuck jaws. Do not
use a wrench to tighten or loosen the chuck jaws.
[] Release the spindle lock button.
Fig. 6
11
REMOVINGBITS
NOTE: For convenience and ease of starting threads, the
hex nut has been trapped inside the molded slot in the
handle assembly.
See Figure 5,
[] Unplug the drill.
The depth stop rod helps control the depth of drilled
holes.
[] Lock the spindle.
[] Open the chuck jaws.
NOTE: When properly installed, the teeth on the depth
stop rod should be aligned with the teeth indicator on the
depth stop clamp.
NOTE: Rotate the chuck body in the direction of the
arrow marked UNLOCK to open the chuck jaws. Do
not use a wrench to tighten or close the chuck jaws.
[] Remove the drill bit.
Adjust the depth stop rod so that the drill bit extends
beyond the end of the rod to the required drilling depth.
[] Release the spindle lock button.
USING
THE AUXILIARY
HANDLE
When drilling holes with the depth stop rod installed, the
desired hole depth has been reached when the end of the
rod comes in contact with the surface of the workpiece.
ASSEMBLY
See Figure 7.
An auxiliary handle assembly is packed with the drill for
ease of operation and to help prevent loss of control. The
handle can be rotated 360 ° , and it can also be mounted
on the opposite side for left hand use.
SELECTING
[] Rotate the handle assembly to the desired operating
position.
NOTE: The hammer drill has not been designed for
reverse hammering.
[] Securely tighten by turning the handle assembly clockwise.
Use carbide-tipped bits and select hammer mode when
drilling in hard materials such as brick, tile, concrete, etc.
Be sure the handle assembly is securely tightened against
the depth stop clamp. This secures the depth stop rod
at the desired depth of cut. It also secures the handle assembly.
DRILL BIT
DRILLINGDEPTH
OR DRILLING
See Figure 8,
[] Loosen the handle assembly by turning the handle
counterclockwise.
DRILLING
DEPTH
MODE
To adjust for type of drilling, slide the drilling mode selector on top of the motor housing to hammer mode or
drilling mode. The hammer mode symbol is on the left and
the drill bit symbol is on the right.
To adjust the auxiliary handle assembly,
TO DECREASE
DRiLLiNGDEPTH
TOINCREASE
HAMMER
MODE
Select normal drill mode when drilling with twist drills, hole
saws, etc., in soft materials.
DRILLING/ HAMMERMODESELECTOR
DRILLINGMODE
DEPTH
STOPROD
TO LOOSENAUXiLiARY
HANDLEASSEMBLY
AND CLAMP
LOCK-ON
BUTTON
Fig. 7
Fig. 8
12
ENDViEW
LOCK-ON BUTTON
See Figure 8,
This drill is equipped with a lock-on feature, which is
convenient for continuous drilling for extended periods of
time. To lock-on:
LEVEL
[] Depress the variable speed switch trigger.
[] Push in and hold the lock-on button, located on the
side of the handle.
[] Release the variable speed switch trigger.
[] Release the lock-on button and the drill will continue
running.
[] To release the lock, depress and release the variable
speed switch trigger.
If the lock-on feature is engaged during use and the drill
becomes disconnected from the power supply, disengage
the lock-on feature immediately.
_1_ WARNING:
Before connecting the drill to a power
supply source, always check to be sure it is not in
lock-on position (depress and release the variable
speed switch trigger). Failure to ensure that it is not
locked-on could result in accidental starting of the
drill resulting in possible serious injury. Do not lock
the variable speed switch trigger in applications
where the drill may need to be suddenly stopped.
DRILLING
See Figure 9.
A level is located on top of the motor housing to help keep
the drill bit level during use.
[] Depress and release the variable speed variable speed
switch trigger to be sure the drill is in the OFF position
before connecting it to a power supply.
[] Check the direction of rotation selector for the correct
setting (forward or reverse).
[] Secure the material to be drilled in a vise or with
Fig. 9
clamps to keep it from turning as the drill bit rotates.
[] When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This will prevent the drill bit from slipping off-center as the hole is
started.
[] Plug the drill into power supply. Hold the drill firmly and
place the bit at the point to be drilled.
[] Depress the variable speed switch trigger to start the
drill.
[] When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life of
the bit and increase the drilling action.
[] Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
the drill or apply side pressure to elongate a hole. Let
the tool do the work.
A
[] If the bit jams in the workpiece or if the drill stalls,
stop the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
WARNING:
Be prepared for binding at bit breakthrough. When these situations occur, the drill has
a tendency to grab and kick in the opposite direction and could cause loss of control when breaking
through material. If not prepared, this loss of control
can result in possible serious injury.
13
WOOD
DRILLING
• Overheat the drill;
For maximum performance, use high speed steel bits for
wood drilling.
Wear the bearings;
[] Select normal drilling mode.
Produce off-center or irregular-shaped
Bend or burn bits; and
holes.
[] Begin drilling at a very low speed to prevent the bit
from slipping off the starting point. Increase the speed
as the drill bit bites into the material.
[] When drilling large holes in metal, start with a small bit,
then finish with a larger bit. Also, lubricate the bit with
oil to improve drilling action and increase bit life.
[] When drilling through holes, place a block of wood
behind the workpiece to prevent ragged or splintered
edges on the back side of the hole.
MASONRY
METAL
DRILLING
For maximum performance, use carbide-tipped masonry
impact bits when drilling holes in brick, tile, concrete, etc.
DRILLING
[] Slide adjustment button on hammer drill left for hammer mode.
For maximum performance, use high speed steel bits for
metal or steel drilling.
[] Select normal drilling mode.
[] Apply light pressure and medium speed for best results
in brick.
[] Begin drilling at a very low speed to prevent the bit
from slipping off the starting point.
[] Apply additional pressure for hard materials such as
concrete.
[] Maintain a speed and pressure which allows cutting
without overheating the bit. Applying too much pressure will:
[] When drilling holes in tile, practice on a scrap piece to
determine the best speed and pressure. Begin drilling
at a very low speed to prevent the bit from slipping off
the starting point.
A
Electric tools used on fiberglass material, wallboard,
spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the
fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not
recommended using this tool for extended work on these
types of materials. However, if you do work with any of
these materials, it is extremely important to clean the tool
using compressed air.
A
WARNING:
When servicing, use only identical
Craftsman replacement parts. Use of any other parts
may create a hazard or cause product damage.
WARNING:
Always wear safety goggles or safety
glasses with side shields during power tool operation
or when blowing dust. If operation is dusty, also wear
a dust mask.
GENERAL
LUBRICATION
MAINTENANCE
All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit
under normal operating conditions. Therefore, no further
lubrication is required.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
,_
WARNING:
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which
may result in serious personal injury.
14
CHUCK REMOVAL
See Figures 10- 12.
MALLET
The chuck may be removed and replaced with a new one.
[] Unplug the drill.
[] Insert a 5/16 in. or larger hex key into the chuck of the
drill and tighten the chuck jaws securely.
[] Tap the hex key sharply with a mallet in a clockwise direction. This will loosen the screw in the chuck for easy
removal.
MALLET
CHUCKJAWS
REXKEY
Fig. 12
[] Insert the hex key into the chuck and tighten the chuck
jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen the chuck on the
spindle. It can now be unscrewed by hand.
TO RETIGHTEN
HEXKEY
[]
A LOOSE CHUCK
The chuck may become loose on the spindle and develop
a wobble. Also, the chuck screw may become loose,
causing the chuck jaws to bind and prevent them from
closing. To tighten:
Open the chuck jaws and remove the hex key. Using a
screwdriver, remove the chuck screw by turning it in a
clockwise direction.
[] Unplug the drill.
NOTE: The chuck screw has left hand threads.
[] Open the chuck jaws.
SCREWDRIVER
[] Insert a hex key into the chuck and tighten chuck jaws
securely. Tap the hex key sharply with a mallet in a
clockwise direction. This will tighten the chuck on the
spindle.
J
[] Open the chuck jaws and remove the hex key.
[] Tighten the chuck screw.
Fig. 11
A
Look for these accessories at Sears retail:
[] High Speed Bits (For wood or metal) (1/2 in. max.)
[] Wood Boring Bits (1 in. max.)
[] Hole Saws (2 in. max.)
[] Masonry Bits (3/4 in. max.)
[] Doweling Jig
[] Drill Stand
[] Wire Brushes, All
15
WARNING"
Current attachments and accessories
available for use with this tool are listed above. Do
not use any attachments or accessories not recommended by the manufacturer of this tool. The use of
attachments or accessories not recommended can
result in serious personal injury.
CRAFTSMAN
DRILL
_"
PROFESSIONAL
MODEL NUMBER
1/2 in. HAMMER
315.265670
J
The
number
model
in all
number
correspondence
will be foundregarding
on a plate
your
attached
HAMMER
to the
DRILL
motoror housing.
when ordering
Always repair
mention
parts,
the model
SEE BACK
PAGE FOR PARTS ORDERING
"!
INSTRUCTIONS
2
1
4
SEENOTE
6
PARTS
LIST
Key
No.
PaN
Number
Description
1
6613402
Screw ..............................................................................................................
1
2
690033076
Chuck ..............................................................................................................
1
3
940057066
Data Plate ........................................................................................................
1
4
940304178
Logo Plate .......................................................................................................
1
5
300188034
Auxiliary Handle Assembly ..............................................................................
1
6
631471001
Depth Stop Rod ..............................................................................................
1
983000853
Operator's
Note:
Qty.
Manual
The assembly shown represents an important part of the double insulated system. To avoid the
possibility of alteration or damage to the system, service should be performed by your nearest
Sears repair center. Contact your nearest Sears retail store for service center information.
* Standard Hardware Item = May Be Purchased Locally
** Available From Div. 98 - Source 980.0
16
Download PDF

advertising