Save This Manual For Future Reference SEARS owner's manual MODEL NO. 113.299720 CRRFTSMRN Serial Number Model and serial numbers may be found on the face beside the switch. You should record both model and serial numbers in a safe AIRBORNE FILTRATION SYSTFM place for future use. • assemmv • operating: • repai_ pa_t_ FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY j Seam, Part No. SP6131 Roebuck and Co., Hoffman Estateb. ILL6_179 U.S.A. Ptinte_l in uJS.A. FULL ONE YEAR WARRANTY ON CRAFTSMAN Airborne Filtration If within one year from the date of purchase, Filtration System fails due to a defect Sears will repair it, free of charge. System this Craftsman in material Airborne or workmanship, If this Craftsman Airborne Filtration System is used for commercial or rental purposes, this warranty coverage applies for only 90 days from date of purchase. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES. This warranty applies only while this product is used in the United States. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., D817 WA, Hoffman Estates, IL. 60179 IMPORTANT SAFETY INSTRUCTIONS Safety is a combination of common sense, staying alert and knowing how your Air- Sparks inside the motor can ignite flammable vapors or dust. To avoid fire or borne Filtration System works. Read this manual to understand the Airborne Filtra- explosion: • Do not use this Airborne Filtration System near flammable or combustible liq- tion System. Safety Signal uids, gases, or explosive dusts, such as gasoline or other fuels, lighter fluid, cleaners, oil- based paints, natural Words DANGER: means if the safety information is not followed someone will be seriously gas, hydrogen, coal dust, magnesium dust, grain dust, or gun powder. injured or killed. WARNING: means if the safety information is not followed someone could be seriously CAUTION: To avoid health hazards dusts, do not operate near toxic materials. Do not use or store near hazardous materials. injured or killed. means if the safety informa- tion is not followed someone might from vapors or To avoid electric shock, do not expose to rain. Store indoors. be injured. Do not allow Airborne When using your Airborne Filtration Sys- be used as a toy. Close attention tem, follow basic safety precautions ing the following. sary when used by or near children. WARNING-To the risk of fire, electric includ- Filtration System to is neces- Do not use this Airborne Filtration System with a torn filter or without the filters reduce installed. shock, or Do not use this Airborne Filtration without fine filter screw installed. injury: System Unplug from outlet before servicing. Turn off Airborne Filtration System before Read and understand this owner's manual and all labels on the Airborne Filtration Sys- unplugging. tem before operating. Use only as described in this manual To avoid personal injury or damage to Airborne Filtration System, use only Sears Craftsman recommended accessories. To avoid injury from accidental starting, unplug power cord before changing or cleaning filters 2 Do not unplugby pullingon cord.To unplug,graspthe plug,not the cord. Do not use withdamagedcord, plug or This product other parts. If your Airborne Filtration System is not working as it should, has missing parts, has been dropped, damaged, left outdoors, or dropped into water, return it to a Sears Service Center. Do not use the top of this unit for storage. Keep cord away from heated surfaces, such as light bulbs or heaters Do not handle plug or the Airborne Filtra- tion System with wet hands. Do not put any object into ventilation openings. should not be used in a spray paint booth or in a kitchen type environment. WARNING: To reduce the risk of electric shock - do not expose rain - store indoors. to WARNING: For your own safety, read and understand owner's manual. Do not use the Airborne Filtration System to filter hot ashes, coals, toxic, flammable or other hazardous materials. Do not use around explosive liquids or vapors. Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts. SAVE THESE INSTRUCTIONS The operation of any power tool can result in foreign objects being blown into the eyes, which can result in severe eye damage. Always wear safety goggles complying with CSA Z94-3-M88 (shown on package) before commencing operation. Safety Goggles are available retail or hardware stores. at Sears Use only extension cords that are rated for outdoor use. Extension cords in poor condition or that are too small in wire size can pose fire and shock hazards. When using an extension cord, be sure it is in good condition. Using any extension cord will cause some loss of power. To keep the loss to a minimum, use the following table to choose the minimum wire size extension cord. Extension Gauge Cord Length (A.W.G.) 0-50 Ft, 50-100 To avoid hearing damage, wear ear protectors when using any power tool for _xtended hours, or when working in a ,oisy area. _:or dust operations, wear dust mask. Ft. 14 12 Contents Item Page Warranty Information ............................. Safety Instructions ................................. Contents ................................................ 2 2 4 Unpacking and Checking Carton Contents ............................. Installation Procedure ............................ 4 5 Unpacking Remove of carton. Check if any parts are damaged C Wiring Diagram ...................................... Repair Parts ........................................ A each item against the Carton Contents List. Notify your Sears Store immediately Key A B Page and Checking Carton Contents entire contents Carton Item Electrical Requirements ........................ Operation ............................................... Maintenance .......................................... or missing, Contents List Description ........................... Qty. Airborne Filtration System .......... 1 Owners Manual ........................... 1 D E Bag of Loose Parts Containing the following: "S" Hook ...................................... Screw Hook ................................. 4 4 F G H J K 3/16-24 Eye Bolt ......................... Extension Spring ......................... Double Loop Chain ..................... 3/16" Lockwasher ........................ 3/16-24 Hex Nut .......................... 4 4 4 8 8 D G © 7 8 8 9 10 -- Installation Procedure WARNING: For your own safety, never connect plug to power source outlet until all assembly steps are 2. Joists are normally sixteen inches apart. Spacing of holes on width of unit is 18-7/8", and on length of unit is 28" on center as shown. Chain allows complete and you have read and understood the safety and operation instructions. Do not operate filter system with any parts damaged for suspension direction. or 3. Unit weighs 40 pounds missing. 1. Select location for Airborne from joist in either so suspension should be from center of ceiling joists only. Filtration System. Unit should be installed with the side opposite the switch and light a minimum distance of six inches to WARNING: To reduce the risk of injury from a falling unit, install in structure that will support 160 the nearest wall. Ends should be at least two feet clear of wall surface to pound allow for proper air circulation shown below. 4. When you have selected the location for your unit, use a pencil to mark the as four suspension points in the joists (again, make sure that these points are at the center of the joists). Drill 1/8" It is important that you select the location carefully so that it is not in a high traffic area, or consider instalting it above a bench to reduce the hazard of diameter pilot holes 1-1/4" deep into each of the four suspension points. bumping your head on the unit. The minimum height required for the unit and suspension will be 17-3/8", so keep this in mind when selecting location. load. 5. Install the four screw hooks in the pilot holes up to the start of the curve as shown on page 6. a 32: ,O/c Wall I I I S urface'_--_ _'1 I I IIi "ii I 28" Olc_ i) TIt- t I .... I J "_ * Minimum Suspension Points(,). Clearance ° I I4 * 24" Un_ , ,• 'll I.J )l "_-_ Ceiling Joist • 24" minimum clearance unit openings, to side. 6" minimum from wall to from wall 5 o _ =o _ _ I _ / Ceiling Joist l I I , Switch & Light Location Filter Unit I, _ .,,_____16,,olc_16,,o/€.__ I o 4 *24" = I Installation Procedure (continued) 6. The next step is to install the eye bolts in the top of the unit. To do this, you must remove the three filters first. Refer to drawing under "Maintenance" section ters. Ceiling Joist for location of three types of fil- 7. The Pre Filter (intake) slides out of the channel in the cabinet. 8. The Fine Filter (mid bag type) has a screw at the center of the bottom of Screw Hook Double Loop Chain the cabinet. To remove the Fine Filter, remove screw and slide filter out about 2" to the right. Push left end of filter into cabinet about 4". Slide filter further into cabinet at an angle. Tilt in at top and pull filter towards you. 9. The diffuser (exhaust) slides out of the channel in the cabinet. 10. Install a hex nut on an eye bolt until 1/4" of thread is showing below the eye. Slip on a Iockwasher and put eye bolt in hole in top of cabinet. Repeat for other three eye bolts. 1 1. Slip Iockwasher and hex nut on eye bolt as shown on Figure "B". Repeat for other three eye bolts and then tighten nuts with two wrenches nuts are snug. 12. Filters can be reinstalled • Diffuser nel. (exhaust) until all at this point. - slide into chan- • Fine Filter (mid bag type) - reverse motions for removing the fine filter, shown in step 8. Reinstall bottom screw. Eye Bolt Lockwashem • Pre Filter (intake) - slide into channel. WARNING: Although compact in size, the Air Filtration Unit weighs 40 Ibs. To avoid back injury obtain to lift the unit into place. Top Cabinet 11" Height of Unit 13.To suspend your unit at the minimum height, five double loop sections of chain are required (4-13/16"). Slip this chain. Repeat for other three springs. Refer to figure shown on previous page. length of chain over the screw eye in 17. Unit is now hung from the ceiling the joist, letting the excess chain hang down in case adjustment of length is required later. 14. Place "S" hook in bottom at four suspension as high as possible. If you prefer the unit to hang lower, unhooking each of the four chains from its screw hook (one link of chain at a time), and rehooking each chain to its screw hook on a different link points. 15. Lift cabinet up, with help and connect "S" hooks to eye bolts at four points in cabinet. can do this. When the hanging height is satisfactory, squeeze all four "S" hook loops closed at the eye bolts and 16. Connect extension springs to "S" hooks. Push unit up and connect chains. (Optional: For a cleaner appearance, snip off extra length of chain links.) upper loop of extension spring to bottom loop of fourth double loop of Electrical Requirements Your filter system is wired for 120 volts A.C. and is equipped with a 3 conductor cord and grounding type plug approved by Underwriters Laboratories and Canadian WARNING: Standards have it checked trician. Connect unit to the nearest 120 volt AC outlet and route cord so that it will not be WARNING: and pulled accidentally. This plug requires Properly Grounded Outlet \ 15 WARNING: Damaged power cords can cause shocks or fires. If the immedi- 3-Prong by Sears Service Centers, using Sears replacement parts. 7 or Plug Grounding Prong WARNING: To assure product SAFETY and RELIABILITY, repairs and adjustment should be performed always plug \ power cord is worn, cut or damaged in any way, have it replaced ately. shock can kill. never connect Unplug filter unit before servicing changing any filters. replace the 2-prong outlet with a grounded amp 3-prong outlet. elec- to power source outlet until all assembly steps are completed. grounded type outlet, properly grounded. If the outlet you are planning to use for this filter unit is of the two prong type DO NOT REMOVE OR ALTER THE GROUNDING PRONG IN ANY MANelectrician by a qualified Electric To avoid shock, a mating 3 conductor NER. Have a qualified shock can kill. Not all outlets are properly grounded. If you are not sure that your outlet is properly grounded, Association easily snagged Electric Operation WARNING: To avoid fire or explosion, do not operate this filter unit in areas with flammable gases or flammable vapors such as lighter fluid, Your Craftsman Airborne Filtration System is equipped with an Pull On/Pull Off switch, a light to show power is ON, and a power cord to plug into your electrical let. cleaners, oil-base paints, gasoline, alcohol or explosive dust such as When installation is complete, plug power cord into wall receptacle. To activate Air- coal, magnesium, grain or gun powder in the air. To avoid health haz- borne Filtration System, pull on switch cord. Light will come on and filter unit is in ards from vapors or dusts, do not use this system to filter toxic materials. The Craftsman Airborne Filtration System is intended out- operation. To stop operation, pull on switch cord and the light will turn off. for indoor Remove power cord from wall receptacle before changing or cleaning filters. use only. Unplug power cord before changing or cleaning filters. WARNING: CAUTION: The operation of any power tool can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety goggles complying with CSA Z94-3-M88 (shown on Package) before commencing operation. Safety Goggles are available at Sears hardware stores. or electrical To reduce the risk of fire shock, do not use this Airborne Filtration System with any solid-state speed control device. Maintenance IMPORTANT: To assure product safety and reliability, repairs and adjustments should only be performed by Sears Service Centers, always using Sears replacement parts. #3 - Diffuser (exhaust) Expanded aluminum The #1 Pre Filter and #3 Diffuser can be washed in warm water with a mild detergent, dried and then reinstalled. Check the filters for tears or small holes. Do not use a filter with holes or tears in it. Filter Maintenance WARNING: To avoid injury from accidentally starting, unplug power cord before cleaning ters. or changing fil- Cleaning ] Replace it immediately. To maintain peak performance clean your filters often. Han- I dle the filters carefully, when removing to clean or when installing. The #2 Fine Filter should be replaced when it becomes clogged with fine dust. A Your Airborne Filtration System consists of three types of filters as shown under "Removal" visual inspection can be done by sliding the #1 Pre Filter out and checking the Fine Filter for contents and tears or holes. #1 - Pre Filter (intake) If tears or holes appear, immediately. Polyurethane foam #2 - Fine Filter (mid-bag type) Non-woven polyester replace your filter Removal WARNING: For your own safety, use only Sears replacement filters. To remove the filters for cleaning or replacement review the section in your manual under "Installation Procedure" fol- WARNING: To avoid electrical shock, be sure to replace screw that secures Fine Filter. lowing steps, 7, 8 and 9. #1 Squirrel Cage Fan Pre Filter (Intake) #2 Fine Filter (Mid-Bag Type) #3 Diffuser (Exhaust) Air Direction I CAUTION: are facing For proper proper direction. operation, the make sure "Air Flow" arrows on the filters Wiring Diagram I White 81ao.-tl / c°nQUi_ikns _1 Wire Nut _.,=!t-_ Black _ Wire NU! _Gr_ound I __ White_ 9 _'_Black Repair Parts Airborne Filtration System Model Number 113.299720 Always Key No. 1 2 3 order by Part Number PaN No. 825702 824294 - Not by Key Number Description Cabinet Assembly Bottom Panel 4 5 9-17931 9-17933 824295 6 7 8 824311 824289 169123-9 Blower Assembly Cord Assembly Stra;n Relief 9 824288 Light 10 11 824292 STD375006 Switch Assembly * Wire Connector 12 13 14 824290 60306 STD551225 Clip Wire _Screw, Pan Hd. Cross Recess 15 16 STD541025 ** 1 Pre Filter - intake 1 Fine Filter - Mid Bag Type Diffuser- Exhaust 17 824301 18 _824299 19 1824302 20 21 22 -'_-"S" Hook 1-1/2" STD541010 STD551210 824298 23:824300 24 _824291 25 26 iSTD551208 809372-3 27 28 29 STD541!10 821330 824597-1 -- SP6131 * Stanc/ard Hardware ** Standard weather 8-32 x 3/8" Lg. * Lockwasher, 1/4" External Type * Hex Nut 1/4-20 Gasket 1/8" Max. Th. x 1/4" x 9" Screw Hook 1-9/16", Eye Bolt 3/16-24 x 2' * Hex Nut 3/16-24 * Lockwasher 3/16" External Type .','Chain, Double Loop Spring, Extension 1-1/4" Clip Wire * Leckwasher - External Type #8 * Screw, Pan Hd Cross Recess10-32 * Hex Nut 10-32 ZN -,.Screw K-Lath #8 x 9/16" Screen, Blower Owners Manual Item - May Be Purchased stripping (purchase 1" Stock Item - May be purchased retail stores. through x 1/2" (Not Illustrated) Locally. locally) the hardware 10 department of most Sears Repair Parts Airborne Filtration System Model Number 113,299720 // / tD \ 11 For the repair or replacement pads you need Call 7 am - 7 pm, 7 days a week 1-8OO-366-PART (1-800-366-7278) For in-home major brand repair service Call 24 hours a day, 7 days a week 1-8OO-4-REPAIR (1-800-473-7247) Far the location of a Sears Repair Service Center in your area Call 24 hours a day, 7 days a week 1-800-488-1222 For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement Call 9 am - 5 prn, Monday-Saturday 1-800-827-6655 SEARS America's Repair Spectahsts The model and serial numbers When requesting service following information: • • Product Type Part Number Seam, Part No. SP6131 will be found on the handle. or ordering • • Roebuck parts, always provide the Model Number Part Description and Co., Chicago, Form No. SP6131 IL. 60179 U.S.A. Printed in U.S.A.