Safety Data Sheet 1. IDENTIFICATION

Safety Data Sheet 1. IDENTIFICATION
Sid Harvey part #'s 12-802, 12-803 and 12-813. SDS # Z0263
Safety Data Sheet
Issue Date 06-18-2015
1. IDENTIFICATION
Product Identifier
Product Name
Plasti-Kleen Plastic Pipe Primer
Other means of identification
SDS #
SDS 12801
UN/ID No
Product Code
UN1993
12-801, 12-802, 12-803, 12-804, 12-811, 12-812, 12-813, 12-814
Recommended use of the chemical and restrictions on use
Recommended Use
Low-VOC primer for plastic pipe
Details of the supplier of the safety data sheet
Manufacturer Address
UTILITY
700 Main Street
Westbury, NY 11590
Emergency Telephone Number
Company Phone Number
Emergency Telephone (24 hr)
1-516-997-6300
INFOTRAC 1-800-535-5053
2. HAZARDS IDENTIFICATION
Appearance Liquid of various colors
Physical State Liquid
Odor Ether-like
Classification
Acute toxicity - Oral
Acute toxicity - Inhalation (Dusts/Mists)
Serious eye damage/eye irritation
Specific target organ toxicity (single exposure)
Flammable Liquids
Category 4
Category 4
Category 2
Category 3
Category 2
Hazards Not Otherwise Classified (HNOC)
May be harmful in contact with skin
Signal Word
Danger
_____________________________________________________________________________________________
Page 1 / 10
Plasti-Kleen Plastic Pipe Primer
12-801, 12-802, 12-803, 12-804, 12-811, 12-812, 12-813, 12-814
_____________________________________________________________________________________________
Hazard Statements
Harmful if swallowed
Harmful if inhaled
Causes serious eye irritation
May cause respiratory irritation. May cause drowsiness or dizziness
Highly flammable liquid and vapor
Precautionary Statements - Prevention
Use personal protective equipment as required
Wash face, hands and any exposed skin thoroughly after handling
Do not eat, drink or smoke when using this product
Avoid breathing dust/fume/gas/mist/vapors/spray
Use only outdoors or in a well-ventilated area
Keep away from heat/sparks/open flames/hot surfaces. — No smoking
Keep container tightly closed
Ground/bond container and receiving equipment
Use explosion-proof equipment
Use only non-sparking tools
Take precautionary measures against static discharge
Wear protective gloves/protective clothing/eye protection/face protection
Keep cool
Precautionary Statements - Response
If exposed or concerned: Get medical advice/attention
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
Immediately call a POISON CENTER or doctor/physician
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing
IF SWALLOWED: Call a POISON CENTER or doctor/physician if you feel unwell
Rinse mouth
IN CASE OF FIRE: Use CO2, dry chemical, or foam for extinction
Precautionary Statements - Storage
Store in a well-ventilated place. Keep container tightly closed
Store locked up
Keep cool
Precautionary Statements - Disposal
Dispose of contents/container to an approved waste disposal plant
WHMIS Classification
Class B-Division 2 Class D-Division 2A Class D-Division 2B
_____________________________________________________________________________________________
Page 2 / 10
Plasti-Kleen Plastic Pipe Primer
12-801, 12-802, 12-803, 12-804, 12-811, 12-812, 12-813, 12-814
_____________________________________________________________________________________________
3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name
Tetrahydrofuran
Methyl ethyl ketone
Cyclohexanone
Acetone
CAS No
109-99-9
78-93-3
108-94-1
67-64-1
Weight-%
Proprietary
Proprietary
Proprietary
Proprietary
* The exact percentage (concentration) of composition has been withheld as a trade secret
4. FIRST-AID MEASURES
First Aid Measures
General Advice
If exposed or concerned: Get medical advice/attention.
Eye Contact
In case of irritation from airborne exposure, move to fresh air. Rinse immediately with plenty
of water, also under the eyelids, for at least 15 minutes. Seek immediate medical
attention/advice.
Skin Contact
Take off contaminated clothing. Wash with soap and water. If symptoms persist, call a
physician. Wash contaminated clothing before reuse.
Inhalation
Remove to fresh air. If symptoms persist, call a physician. If breathing is difficult, give
oxygen. Seek immediate medical attention/advice.
Ingestion
Rinse mouth. Seek medical attention. If drowsy or unconscious, do not give anything by
mouth; place individual on the left side with head down. Do not induce vomiting.
Most important symptoms and effects
Symptoms
Exposed individuals may experience eye tearing, redness and discomfort. Prolonged or
repeated skin contact may result in dermatitis (red, dry skin). May cause nose and throat
irritation, with possible central nervous system effects. Fatigue and weakness. May cause
drowsiness or dizziness. Long term overexposure may cause liver and kidney damage.
Indication of any immediate medical attention and special treatment needed
Notes to Physician
Treat symptomatically. Individuals with chronic respiratory, skin, kidney, or liver disorders
may be at increased risk from exposure.
5. FIRE-FIGHTING MEASURES
Suitable Extinguishing Media
Foam. Carbon dioxide (CO2). Dry chemical.
Unsuitable Extinguishing Media Not determined.
Specific Hazards Arising from the Chemical
Class IB Flammable Liquid. Vapors may travel to source of ignition and flash back.
Hazardous Combustion Products Carbon oxides. Various hydrocarbon vapors and toxic gases.
Protective equipment and precautions for firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full
protective gear.
_____________________________________________________________________________________________
Page 3 / 10
Plasti-Kleen Plastic Pipe Primer
12-801, 12-802, 12-803, 12-804, 12-811, 12-812, 12-813, 12-814
_____________________________________________________________________________________________
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Personal Precautions
Use personal protective equipment as required. ELIMINATE all ignition sources (no
smoking, flares, sparks or flames in immediate area). Persons not wearing proper personal
protective equipment should be excluded from area of spill.
Environmental Precautions
Do not allow into any sewer, on the ground or into any body of water.
Methods and material for containment and cleaning up
Methods for Containment
Prevent further leakage or spillage if safe to do so.
Methods for Clean-Up
Pump or vacuum transfer spilled product to clean containers for recovery. Absorb
unrecoverable product. Transfer contaminated absorbent, soil and other materials to
containers for disposal.
7. HANDLING AND STORAGE
Precautions for safe handling
Advice on Safe Handling
Wash thoroughly after handling. Use personal protection recommended in Section 8. Do
not eat, drink or smoke when using this product. Avoid breathing vapors or mists. Use only
in well-ventilated areas. Ground/bond container and receiving equipment. Keep away from
heat/sparks/open flames/hot surfaces. — No smoking. Use spark-proof tools and explosionproof equipment. Take precautionary measures against static discharges. Containers of this
material may be hazardous when emptied. Since emptied containers retain product
residues (vapor, liquid, solid) all hazard precautions given in the data sheet must be
observed. Avoid prolonged contact with eyes, skin, and clothing. Obtain special instructions
before use. Do not handle until all safety precautions have been read and understood.
Conditions for safe storage, including any incompatibilities
Storage Conditions
Keep containers tightly closed in a dry, cool and well-ventilated place. Store containers
upright. Store away from heat, sparks, flame.
Incompatible Materials
Oxidizers. Acids. Bases.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Exposure Guidelines
Chemical Name
Tetrahydrofuran
109-99-9
ACGIH TLV
STEL: 100 ppm
TWA: 50 ppm
S*
OSHA PEL
TWA: 200 ppm
3
TWA: 590 mg/m
(vacated) TWA: 200 ppm
3
(vacated) TWA: 590 mg/m
(vacated) STEL: 250 ppm
3
(vacated) STEL: 735 mg/m
NIOSH IDLH
IDLH: 2000 ppm
TWA: 200 ppm
3
TWA: 590 mg/m
STEL: 250 ppm
3
STEL: 735 mg/m
_____________________________________________________________________________________________
Page 4 / 10
Plasti-Kleen Plastic Pipe Primer
12-801, 12-802, 12-803, 12-804, 12-811, 12-812, 12-813, 12-814
_____________________________________________________________________________________________
Acetone
67-64-1
STEL: 750 ppm
TWA: 500 ppm
Methyl ethyl ketone
78-93-3
STEL: 300 ppm
TWA: 200 ppm
Cyclohexanone
108-94-1
STEL: 50 ppm
TWA: 20 ppm
S*
TWA: 1000 ppm
3
TWA: 2400 mg/m
(vacated) TWA: 750 ppm
3
(vacated) TWA: 1800 mg/m
3
(vacated) STEL: 2400 mg/m
The acetone STEL does not apply
to the cellulose acetate fiber
industry. It is in effect for all other
sectors
(vacated) STEL: 1000 ppm
TWA: 200 ppm
3
TWA: 590 mg/m
(vacated) TWA: 200 ppm
3
(vacated) TWA: 590 mg/m
(vacated) STEL: 300 ppm
3
(vacated) STEL: 885 mg/m
TWA: 50 ppm
3
TWA: 200 mg/m
(vacated) TWA: 25 ppm
3
(vacated) TWA: 100 mg/m
(vacated) S*
IDLH: 2500 ppm
TWA: 250 ppm
3
TWA: 590 mg/m
IDLH: 3000 ppm
TWA: 200 ppm
3
TWA: 590 mg/m
STEL: 300 ppm
3
STEL: 885 mg/m
IDLH: 700 ppm
TWA: 25 ppm
3
TWA: 100 mg/m
Appropriate engineering controls
Engineering Controls
Apply technical measures to comply with the occupational exposure limits. Ventilation
systems. Eyewash stations. Showers. Mechanical exhaust (explosion proof) may be
required.
Individual protection measures, such as personal protective equipment
Eye/Face Protection
Splash goggles or safety glasses.
Skin and Body Protection
Rubber gloves. Use body protection appropriate for task.
Respiratory Protection
Not required under normal conditions. If recommended levels are exceeded, respiratory
protection must be selected to assure compliance with OSHA Standard 29CFR 1910.134.
General Hygiene Considerations Handle in accordance with good industrial hygiene and safety practice.
9. PHYSICAL AND CHEMICAL PROPERTIES
Information on basic physical and chemical properties
Physical State
Appearance
Color
Liquid
Liquid of various colors
Clear or purple
Property
pH
Melting Point/Freezing Point
Boiling Point/Boiling Range
Flash Point
Evaporation Rate
Flammability (Solid, Gas)
Upper Flammability Limits
Lower Flammability Limit
Vapour Pressure
Vapor Density
Specific Gravity
Water Solubility
Values
Not available
not determined
66 °C / 151 °F
-14 °C / 6 °F
> 1.0
n/a-liquid
12.8%
1.8%
143 mm
Hg 2.5
0.820
Negligible
Odor
Odor Threshold
Ether-like
0.88 ppm
Remarks • Method
(butyl acetate = 1)
@ 20°C (68°F)
(Air=1)
_____________________________________________________________________________________________
Page 5 / 10
Plasti-Kleen Plastic Pipe Primer
12-801, 12-802, 12-803, 12-804, 12-811, 12-812, 12-813, 12-814
_____________________________________________________________________________________________
Solubility in other solvents
Partition Coefficient
Auto-ignition Temperature
Decomposition Temperature
Kinematic Viscosity
Dynamic Viscosity
Explosive Properties
Oxidizing Properties
VOC Content
Not determined
Not determined
Not determined
Not determined
Not determined
Not determined
Not determined
Not determined
Maximum VOC emissions when applied and tested per SCAQMD Rule 1168, Test Method
316A is 550 g/L
10. STABILITY AND REACTIVITY
Reactivity
Not reactive under normal conditions.
Chemical Stability
Stable under recommended storage conditions.
Possibility of Hazardous Reactions
None under normal processing.
Hazardous Polymerization
Hazardous polymerization does not occur.
Conditions to Avoid
Avoid heat, sparks, open flames and other ignition sources.
Incompatible Materials
Oxidizers. Acids. Bases.
Hazardous Decomposition Products
Carbon oxides. Hydrogen chloride. Other various hydrocarbons.
11. TOXICOLOGICAL INFORMATION
Information on likely routes of exposure
Product Information
Eye Contact
Causes serious eye irritation.
Skin Contact
May be harmful in contact with skin.
Inhalation
Harmful if inhaled.
Ingestion
Harmful if swallowed.
Component Information
Chemical Name
Tetrahydrofuran
109-99-9
Acetone
67-64-1
Methyl ethyl ketone
78-93-3
Cyclohexanone
108-94-1
Oral LD50
= 1650 mg/kg ( Rat )
Dermal LD50
-
= 5800 mg/kg ( Rat )
-
Inhalation LC50
= 53.9 mg/L ( Rat ) 4 h = 180 mg/L
( Rat ) 1 h
-
= 2737 mg/kg ( Rat )
= 6480 mg/kg ( Rabbit )
-
= 800 mg/kg ( Rat )
= 948 mg/kg ( Rabbit )
= 10.7 mg/L ( Rat ) 4 h = 8000 ppm
( Rat ) 4 h
_____________________________________________________________________________________________
Page 6 / 10
Plasti-Kleen Plastic Pipe Primer
12-801, 12-802, 12-803, 12-804, 12-811, 12-812, 12-813, 12-814
_____________________________________________________________________________________________
Information on physical, chemical and toxicological effects
Symptoms
Please see section 4 of this SDS for symptoms.
Delayed and immediate effects as well as chronic effects from short and long-term exposure
Carcinogenicity
The table below indicates whether each agency has listed any ingredient as a carcinogen.
However, the product as a whole has not been tested.
Chemical Name
Tetrahydrofuran
109-99-9
Cyclohexanone
108-94-1
ACGIH
A3
IARC
A3
Group 3
NTP
OSHA
Legend
ACGIH (American Conference of Governmental Industrial Hygienists)
A3 - Animal Carcinogen
IARC (International Agency for Research on Cancer)
Group 3 IARC components are "not classifiable as human carcinogens"
STOT - single exposure
May cause respiratory irritation. May cause drowsiness or dizziness.
Numerical measures of toxicity
Not determined
12. ECOLOGICAL INFORMATION
Ecotoxicity
Category IV
Chemical Name
Algae/aquatic plants
Tetrahydrofuran
109-99-9
Toxicity to
microorganisms
1970 - 2360: 96 h
Pimephales promelas mg/L
LC50 flow-through 2700 3600: 96 h Pimephales
promelas mg/L LC50 static
EC50 = 14500 mg/L 15 min
4.74 - 6.33: 96 h
Oncorhynchus mykiss mL/L
LC50 6210 - 8120: 96 h
Pimephales promelas mg/L
LC50 static 8300: 96 h
Lepomis macrochirus mg/L
LC50
3130 - 3320: 96 h
EC50 = 3403 mg/L 30 min
Pimephales promelas mg/L EC50 = 3426 mg/L 5 min
LC50 flow-through
Acetone
67-64-1
Methyl ethyl ketone
78-93-3
Cyclohexanone
108-94-1
Fish
20: 96 h Chlorella vulgaris
mg/L EC50
481 - 578: 96 h Pimephales
promelas mg/L LC50 flowthrough 8.9: 96 h
Pimephales promelas mg/L
LC50
EC50 = 18.5 mg/L 5 min
EC50 = 21.3 mg/L 10 min
EC50 = 25 mg/L 5 min
Crustacea
5930: 24 h Daphnia magna
mg/L EC50
10294 - 17704: 48 h Daphnia
magna mg/L EC50 Static
12600 - 12700: 48 h Daphnia
magna mg/L EC50
520: 48 h Daphnia magna
mg/L EC50 5091: 48 h
Daphnia magna mg/L EC50
4025 - 6440: 48 h Daphnia
magna mg/L EC50 Static
800: 24 h Daphnia magna
mg/L EC50
Persistence/Degradability
Not determined.
_____________________________________________________________________________________________
Page 7 / 10
Plasti-Kleen Plastic Pipe Primer
12-801, 12-802, 12-803, 12-804, 12-811, 12-812, 12-813, 12-814
_____________________________________________________________________________________________
Bioaccumulation
Not determined.
Mobility
Chemical Name
Tetrahydrofuran
109-99-9
Methyl ethyl ketone
78-93-3
Cyclohexanone
108-94-1
Acetone
67-64-1
Partition Coefficient
0.45
0.29
0.86
-0.24
Other Adverse Effects
Not determined
13. DISPOSAL CONSIDERATIONS
Waste Treatment Methods
Disposal of Wastes
Disposal should be in accordance with applicable regional, national and local laws and
regulations.
Contaminated Packaging
Disposal should be in accordance with applicable regional, national and local laws and
regulations.
US EPA Waste Number
Chemical Name
Tetrahydrofuran
109-99-9
Acetone
67-64-1
Methyl ethyl ketone
78-93-3
Cyclohexanone
108-94-1
RCRA
U159
RCRA - Basis for Listing
Included in waste stream:
F039
Included in waste streams:
F005, F039
Included in waste stream:
F039
RCRA - D Series Wastes
RCRA - U Series Wastes
U213
U002
200.0 mg/L regulatory level
U159
U057
California Hazardous Waste Status
Chemical Name
Tetrahydrofuran
109-99-9
Methyl ethyl ketone
78-93-3
Acetone
67-64-1
California Hazardous Waste Status
Toxic
Ignitable
Toxic
Ignitable
Ignitable
14. TRANSPORT INFORMATION
Note
DOT
UN/ID No
Proper Shipping Name
Please see current shipping paper for most up to date shipping information, including
exemptions and special circumstances. Shipments of containers holding 5 Liters or less per
inner packaging may qualify for a "Limited Quantity" exception. Refer to 49 CFR 173.150
for additional information.
UN1993
Flammable liquid, n.o.s. (Methyl ethyl ketone, Acetone)
_____________________________________________________________________________________________
Page 8 / 10
Plasti-Kleen Plastic Pipe Primer
12-801, 12-802, 12-803, 12-804, 12-811, 12-812, 12-813, 12-814
_____________________________________________________________________________________________
Hazard Class
Packing Group
3
II
IATA
UN/ID No
Proper Shipping Name
Hazard Class
Packing Group
UN1993
Flammable liquid, n.o.s. (Methyl ethyl ketone, Acetone)
3
II
IMDG
UN/ID No
Proper Shipping Name
Hazard Class
Packing Group
Marine Pollutant
UN1993
Flammable liquid, n.o.s. (Methyl ethyl ketone, Acetone)
3
II
No
15. REGULATORY INFORMATION
International Inventories
TSCA
Listed
Legend:
TSCA - United States Toxic Substances Control Act Section 8(b) Inventory
DSL/NDSL - Canadian Domestic Substances List/Non-Domestic Substances List
EINECS/ELINCS - European Inventory of Existing Chemical Substances/European List of Notified Chemical Substances
ENCS - Japan Existing and New Chemical Substances
IECSC - China Inventory of Existing Chemical Substances
KECL - Korean Existing and Evaluated Chemical Substances
PICCS - Philippines Inventory of Chemicals and Chemical Substances
US Federal Regulations
CERCLA
Chemical Name
Tetrahydrofuran
109-99-9
Methyl ethyl ketone
78-93-3
Cyclohexanone
108-94-1
Acetone
67-64-1
Hazardous Substances RQs
1000 lb
5000 lb
5000 lb
5000 lb
CERCLA/SARA RQ
Reportable Quantity (RQ)
RQ 1000 lb final RQ
RQ 454 kg final RQ
RQ 5000 lb final RQ
RQ 2270 kg final RQ
RQ 5000 lb final RQ
RQ 2270 kg final RQ
RQ 5000 lb final RQ
RQ 2270 kg final RQ
SARA 313
Not determined
US State Regulations
California Proposition 65
This product may contain trace levels of chemicals known to the State of California to cause cancer. Exposure to these chemicals
above the State of California 'No Significant Risk Level' is unlikely under normal use conditions.
_____________________________________________________________________________________________
Page 9 / 10
Plasti-Kleen Plastic Pipe Primer
12-801, 12-802, 12-803, 12-804, 12-811, 12-812, 12-813, 12-814
_____________________________________________________________________________________________
U.S. State Right-to-Know Regulations
Chemical Name
Tetrahydrofuran
109-99-9
Acetone
67-64-1
Methyl ethyl ketone
78-93-3
Cyclohexanone
108-94-1
New Jersey
X
Massachusetts
X
Pennsylvania
X
X
X
X
X
X
X
X
X
X
16. OTHER INFORMATION
NFPA
HMIS
Health Hazards
2
Health Hazards
2
Flammability
3
Flammability
3
Instability
1
Physical Hazards
1
Special Hazards
None
Personal Protection
G
Disclaimer
The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the
date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage,
transportation, disposal and release and is not to be considered a warranty or quality specification. The information
relates only to the specific material designated and may not be valid for such material used in combination with any other
materials or in any process, unless specified in the text. Information on this form is furnished solely for the purpose of
compliance with the Occupational Safety and Health Act and shall not be used for any other purpose. UTILITY urges the
customers receiving this Material Safety Data Sheet to study it carefully to become aware of the hazards, if any, of the
product involved. In the interest of safety, you should notify your employees, agents, and contractors of the information
on the sheets. The information herein has been compiled from sources believed to be reliable, up-to-date, and is accurate
to the best of our knowledge. However, UTILITY cannot give any guarantees regarding information from other sources,
and expressly does not make warranties, nor assumes any liability for its use. The information given is designed only as
a guide for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered as a
warranty or quality specification. The information relates only to the specific material designated and may not be valid for
such material used in combination with any other material or in any process, unless specified.
End of Safety Data Sheet
_____________________________________________________________________________________________
Page 10 / 10
\,
UTILITY MANUFACTURING CO., INC.
MAIN STREET, WESTBURY, NY 11590
(516) 997-6300 - FAX # (516) 997-6345
MATERIAL SAFETY DATA SHEET
'>-,",,~M
PLASTI-KLEEN PURPLE PLASTIC PIPE PRIMER
FOR CHEMICAL EMERGENCY: Spill, Leak, Fire, Exposure, or Accident - Call INFOTRAC - Day or Night: 1-800-535-5053
THIS MSDS COMPLIES WITH 29 CFR 1910.1200 (HAZARD COMMUNICATION STANDARD) IMPORTANT: Read this MSDS
before handling & disposing of this product. Pass this infonnation on to employees, customers and users of this product.
PRODUCT IDENTIFICATION
DOT Shipping name:
ADHESIVES, CONTAINING FLAMMABLE LIQUID
CAS NO.: MIXTURE
Chemical Family: OXYGENATED
UNINA#: UN1l33
DOT Hazard Class:
3
DATE OF ISSUE: I t 106
SECTION I - HAZARDOUS INGREDIENTSIEXPOSURE LIMITS
Hazardous Ingredients:
CAS #
METHYL ETHYl_ KETONE 78-93-3
108-94-1
CYCLOHEXANONE
TETRAHYDROFURAN
109-99-9
TLVIPEL
200PPM
2SPPM
200PPM
AGENCY
ACGlH
ACGlH
ACGlH
TYPE
TWA
TWA(SKIN)
TWA
SARA·313(% Range)
40-50
2-5
30-40
SECTION II - EMERGENCY AND FIRST AID PROCEDURES
EYE CONTACT: Flush with water for at least 15 minutes. Seek medical attention.
SKIN CONTACT: Remove contaminated shoes and clothing and cleanse affected areas thoroughly by washing with mild soap and water.
If irritation persists seek medical attention.
INHALATION: (breathing) Remove victim from exposure, If breathing has stopped, give artificial respiration, then oxygen as needed,
INGESTION: (swallowing) Do not induce vomiting. Give victim large quantities of water if conscious. Seck medical attention.
SECTION III - HEALTH HAZARDS I ROUTES OF ENTRY
EYE CONTACT: Severely irritating, If not removed promptly, will injure eye tissue and may result in permanent damage.
SKIN CONTACT: Frequent or prolonged contact may irritate and cause dermatitis.
SKIN ABSORPTION: Can be absorbed through skin causing systemic effects similar to inhalation.
INHALATION: (breathing) Vapor concentr~tions above recommended exposure levels are irritating to the respiratory tract. May cause
headache and dizziness. Are anesthetic and may have other central nervous system effects,
INGESTION: ingestion of this material may cause the following: Irritation of the digestive tract, signs of nervous system depression, such
as headache. drowsiness, dizziness, .loss of coordination, fatigue and nausea,
SECTION IV - SPECIAL PROTECTION INFORMATION
VENTILATION: Provide ventilation adequate to maintain airborne concentrations below established exposure limits (see Section 1)
RESPIRATORY PROTECTION: The use of respiratory protection is advised when concentrates exceed the established exposure limits
(see Section I), Depending on the airborne concentration use a respirator or gas mask with appropriate cartridges or canisters
(NIOSH approved) or supplied air. .
PROTECTIVE GLOVES: The use of gloves impermeable to the specific material handled is advised to prevent possible irritation.
EYE PROTECTION: Approved eye protection to safeguard against potential eye contact, irritation or injury is recommended.
SECTION V - REACTIVITY DATA
STABILITY: Stable
INCOMPATffiILITY: (materials to avoid) This product is incompatible with: Oxidizing agents, strong acids and bases
HAZARDOUS DECOMPOSITION PRODUCTS: Thennal decomposition in the presence of air may yield carbon monoxide, carbon
dioxide.
HAZARDOUS POLYMERIZAnON: Will not occur
SECTION VI - SPILL OR LEAK PROCEDURES
PRECAUTIONS IN CASE OF LEAK OR SPILL: Keep all sources of ignition and hot metal surfaces away from spill/release. Wear
appropriate protective equipment including respiratory protection as conditions warrant (see Section IV). Prevent spilled material from
entering sewers, storm drains, and natural waterways. Spilled material may be absorbed by an appropriate absorbent.
WASTE DISPOSAL METHOD: Dispose of product in accordance with local, county, state, and federal regulations.
Page 1
112801
"
UTILITY MANUFACTURING CO., INC.
MAIN STREET, WESTBURY, NY 11590
(516) 997-6300 - FAX # (516) 997-6345
MATERIAL SAFETY DATA SHEET
PLASTI-KLEEN PURPLE PLASTIC PIPE PRlMER
SECTION vn - STORAGE AND SPECIAL PRECAUTIONS
HANDLING AND STORAGE PRECAUTIONS: Do not get in eyes, skin or clothing. Do not breathe vapor mist or gas. Keep
containers tightly closed, cool, dry, and away from all sources of ignition. Use and store this product with adequate ventilation.
Avoid inhalation of vapors and personal contact with the product. Use good personal hygiene practices. Bond and ground
equipment when transferring to another container. "Empty" containers contain residue (liquid and/or vapor) and can be
dangerous. Do not pressurize, cut, weld, braze, solder, drm, grind, or expose such containers to heat, flame, sparks, or other
sources of ignition. They may explode and cause injury and death All containers should be disposed of in an environmentally
safe manner and in accordance with governmental regulations
SECTION VITI - FIRE AND EXPLOSION HAZARD DATA
EXTINGUISHING MEDIA: Extinguish with dry chemical, CO2 , or a universal type foam.
FIRE AND EXPLOSION HAZARD: Extremely flammable. Vapors are heavier than air an may travel to a source of ignition. Use water
spray to cool containers exposed to fire.
FIRE FIGHTING PROCEDURES: Wear appropriate protective equipment including respiratory protection as conditions warrant (see
Section IV). Stop spill/release if it can be done without risk. Water spray may be useful in minimizing or dispersing vapors and
cooling equipment exposed to heat and flame.
SECTION IX - PHYSICAL DATA
ApPROXIMATE BOILING POINT (DEG F): >200
SPECIFIC GRAVITY (68 Fh >1
RELATIVE EVAPORA TlON RATE (ESTIMATED):<1
VAPOR PRESSURE @20C mmHg (CALCULATED):<l
PER CENT VOLATILE: >80
FLASH POINT (TCC, DEG F): 24 SOLVENT
PER CENT SOLUBILITY IN WATER: 85
SECTION X. OTHER REGULATORY DATA
SECTION 302: NONE
SECTION 311 & 312: ACUTE, CHRONIC, FIRE
SECTION 313: See Section I.I
All components are in full compliance
with the TSCA inventory.
Waste material would be a DOOI
Health:
Flammability:
Reactivity:
3
3
o
CALIFORNIA PROPOSITION 65
NOT LISTED
CERCLA
TETRAHYDROFURAN RQ: 1000 LBS.
METHYL ETIlYL KETONE RQ: 5000 LBS.
CYCLOHEXANONE RQ: 5000 LBS.
CARCINOGENICITY:
NOT LISTED with NTP or IARC.
The supplier disclaims all expressed or implied warranties of merchantability or fitness for a specific use, with respect to the product or the information
provided herein, except for conformation to contracted specifications. All information appearing herein is based upon data obtained from manufactures
andlor recognized technical sources, While the infonnation is believed to be accurate, we make no representations as to its accuracy or sufficiency.
Conditions of use are beyond our control, and therefore users are responsible for verifying the data under their own operating conditions to determine
whether the product is suitable for their particular purposes and they assume risks of their use, handling, and disposal of the product. Users also assume all
risks in regards to the publication or use of, or reliance upon, information contained herein. This information relates only to the product designated herein,
and does not relate to its use in combination with any other material or process,
Page 2
112801
"
UTILITY MANUFACTURING CO., INC.
MAIN STREET, WESTBURY, NY 11590
(516) 997-6300 - FAX # (516) 997-6345
MATERIAL SAFETY DATA SHEET
PLASTI-KLEEN CLEAR PLASTIC PIPE PRIMER
FOR CHEMICAL EMERGENCY: Spill, Leak, Fire, Exposure, Of Accident - Call INFOTRAC - Day or Night: 1-800-535-5053
THIS MSDS COMPLIES WITH 29 CFR 1910.1200 (HAZARD COMMUNICATION STANDARD) IMPORTANT: Read this MSDS
before hand1ing & disposing of this product. Pass this information on to employees, customers and users of this product.
PRODUCT IDENTIFICATION
DOT Shipping name:
ADHESIVES, CONTAINING FLAMMABLE LIQUID
CAS NO.: MIXTURE
Chemical Family: OXYGENATED
UNINA#: UN1133
DOT Hazard Class:
3
DATE OF ISSUE: Il106
SECTION I - HAZARDOUS INGREDIENTS/EXPOSURE LIMITS
Hazardous Ingredients:
METHYL ETHYL KETONE
CVCLOIIEXANONE
TETRAHYDROFURAN
CAS #
78·93-3
108-94-1
109-99-9
TLVIPEL
200PPM
25PPM
200PPM
AGENCY
ACGIH
ACGIH
ACGIH
TYPE
TWA
TWA(SKlN)
TWA
SARA-313(% Range)
40-50
2-5
30-40
SECTION IT - EMERGENCY AND FIRST AID PROCEDURES
EYE CONTACT: Flush with water for at least 15 minutes. Seek medical attention.
SKIN CONTACT: Remove contaminated shoes and clothing and cleanse affected areas thoroughly by washing with mild soap and water.
If irritation persists seek medical attention.
INHALATION: (breathing) Remove victim from exposure. If breathing has stopped, give artificial respiration, then oxygen as needed.
INGESTION: (swallowing) Do not induce vomiting. Give victim large quantities of water if conscious. Seek medical attention.
SECTION 1lI - HEALTH HAZARDS / ROUTES OF ENTRY
EYE CONTACT: Severely irritating. If not removed promptly, will injure eye tissue and may result in permanent damage.
SKIN CONTACT: Frequent or prolonged contact may irritate and cause dennatitis.
SKIN ABSORPTION: Can be absorbed through skin causing systemic effects similar to inhalation.
INHALATION: (breathing) Vapor concentrations above recommended exposure levels are irritating to the respiratory tract. May cause
headache and dizziness. Are anesthetic and may have other central nervous system effects.
INGESTION: ingestion of this material may cause the following: Irritation of the digestive tract, signs of nervous system depression, such
as headache, drowsiness, dizziness, loss of coordination, fatigue and nausea.
SECTION IV - SPECIAL PROTECTION INFORMATION
VENTILATION: Provide ventilation adequate to maintain airborne concentrations below established exposure limits (see Section I)
RESPIRATORY PROTECTION: The use of respiratory protection is advised when concentrates exceed the established exposure limits
(see Section I). Depending on the airborne concentration use a respirator or gas mask with appropriate cartridges or canisters
(NIOSH approved) or supplied air.
PROTECTIVE GLOVES: The use of gloves impermeable to the specific material handled is advised to prevent possible irritation.
EYE PROTECTION: Approved eye protection to safeguard against potential eye contact, irritation or injury is recommended.
SECTION V - REACTIVITY DATA
STABILITY: Stable
INCOMPATIBILITY: (materials to avoid) 'Dlis product is incompatible with: Oxidizing agents, strong acids and bases
HAZARDOUS DECOMPOSITION PRODUCTS: Thennal decomposition in the presence of air may yield carbon monoxide, carbon
dioxide.
HAZARDOUS POLYMERIZATION: Will not occur
SECTION VI - SPILL OR LEAK PROCEDURES
PRECAUTIONS IN CASE OF LEAK OR SPILL: Keep all sources of ignition and hot metal surfaces away from spilllrelease. Wear
appropriate protective equipment including respiratory protection as conditions warrant (see Section IV). Prevent spilled material from
entering sewers, storm drains, and natural waterways. Spilled material may be absorbed by an appropriate absorbent.
WASTE DISPOSAL METHOD: Dispose of product in accordance with local, county, state, and federal regulations.
Page 1
112811
l'
UTILITY MANUFACTURING CO., INC.
MAIN STREET. WESTBURY, NY 11590
(516) 997-6300 - FAX # (516) 997-6345
MATERIAL SAFETY DATA SHEET
PLASTI-KLEEN CLEAR PLASTIC PIPE PRIMER
I
SECTION VII - STORAGE AND SPECIAL PRECAUTIONS
HANDLING AND STORAGE PRECAUTIONS: Do not get in eyes, skin or clothing. Do not breathe vapor mist or gas. Keep
containers tightly closed, cool, dry, and away from all sources of ignition. Use and store this product with adequate ventilation.
Avoid inhalation of vapors and personal contact with the product. Use good personal hygiene practices. Bond and ground
equipment when transferring to another container. "Empty" containers contain residue (liquid andlor vapor) and can be
dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, or other
sources of ignition. They may explode and cause injury and death All containers should be disposed of in an environmentally
safe manner and in accordance with governmental regulations
I
SECTION VIII - FIRE AND EXPLOSION HAZARD DATA
EXTINGUISHING MEDIA: Extinguish with dry chemical, CO2 , or a universal type foam.
FIRE AND EXPLOSION HAZARD: Extremely flammable. Vapors are heavier than air an may travel to a source of ignition. Use water
spray to cool containers exposed to fire.
FIRE FIGHTING PROCEDURES: Wear appropriate protective equipment including respiratory protection as conditions warrant (see
Section IV). Stop spill/release if it can be done without risk. Water spray may be useful in minimizing or dispersing vapors and
cooling equipment exposed to heat and flame.
SECTION IX - PHYSICAL DATA
PER CENT VOLATILE: >80
APPROXIMATE BOILING POINT (DEG F): >200
SPECIFICGRAVITY(68F): >1
RELATIVE EV APORA TION RATE (ESTIMATED):<I
VAPOR PRESSURE @20C mmHg (CALCULATED)«I
FLASH POINT (TCC, DEG F): 24 SOLVENT
PER CENT SOLUBILITY IN WATER: 85
SECTION X - OTHER REGULATORY DATA
SECTION 302: NONE
SECTION 311 & 312: ACUTE, CHRONIC, FIRE
SECTION 313: See Section I.I
All components are in full compliance
with the TSCA inventory.
Waste material would be a 0001
Health:
Flammability:
Reactivity:
3
3
o
CALIFORNIA PROPOSITION 65
NOT LISTED
CERCLA
TETRAHYDROFURAN RQ: 1000 LBS.
METHYL ETHYL KETONE RQ: 5000 LBS.
CYCLOHEXANONE RQ: 5000 LBS.
CARCINOGENICITY:
NOT LISTED with NTP or IARe.
The supplier disclaims all expressed or implied warranties of merchantability or fitness for a specific use, with respect to the product or the information
provided herein, except for confonnation to contracted specifications. All information appearing herein is based upon data obtained from manufactures
and/or recognized technical sources. While the information is believed to be accurate, we make no representations as to its accuracy or sufficiency.
Conditions of use are beyond our control, and therefore users are responsible for verifying the data under their own operating conditions to detennine
whether the product is suitable for their particular purposes and they assume risks of their use, handling, and disposal of the product. Users also assume all
risks in regards to the publication or use of, or reliance upon, information contained herein. This information relates only to the product designated herein,
and does not relate to its use in combination with any other material or process.
Page 2
112811
"
"
f.
~.
'"
UTILITY MANUFACTURING CO., INC.
11590
(516) 997-6300 - FAX # (516) 997-6345
MATERIAL SAFETY DATA SHEET
'0 U:'~,>:,. 700 MAIN STREET, WESTBURY, NY
~:" •• "o ••
PLASTI-SEAL PVC CLEAR GLOO REGULAR BODY SOLVENT CEMENT
FOR CHEMICAL EMERGENCY: Spill, Leak, Fire, Exposure, or Accident - Call CHEMTREC - Day or Night: 1-800-424-9300
THIS MSDS COMPLIES WITH 29 CFR 1910.1200 (HAZARD COMMUNICATION STANDARD) IMPORTANT: Read this MSDS
before handling & disposing of this product. Pass this information on to employees, customers and users of this product.
PRODUCT IDENTIFICATION
DOT Shipping name:
ADHESIVES, CONTAINING FLAMMABLE UQUlD
CAS NO.:MlXTURE
Chemical Family: OXYGENATED
UNINA#: UNit33
DOT Hazard Class:
3
CYCLOHEXANONE
TETRAHYDROFURAN
108-94-1
109·99·9
DATE OF ISSUE:t t/06
78-93-3
I
200PPM
25PPM
200PPM
ACGIH
ACGIH
TWA(SKIN)
TWA
TWA
2-5
30-40
40-50
SECTION II - EMERGENCY AND FIRST AID PROCEDURES
EYE CONTACT: Move person away from exposure and into fresh air. If irritation or redness develops, flush eyes with clean water and
seek medical attention. For direct contact hold eyelids apart for at least 15 minutes. Seek medical attention.
SKIN CONTACT: Remove contaminated shoes and clothing and cleanse affected areas thoroughly by washing with mild soap and water.
If irritation persists seek medical attention.
INHALATION: (breathing) Not expected to be a hazard under normal operating conditions ..
INGESTION: (swallowing) If swallowed, seek emergency medical attention. Do not give anything by mouth.
I
SECTION III - HEALTH HAZARDS I ROUTES OF ENTRY
EYE CONTACT: One or more components of this material may be an eye irritant.
SKIN CONTACT: Continuous contact with this material may cause drying of skin. Chemical itself is an irritant or sensitizer.
SKIN ABSORPTION: Symptoms of toxicity are anticipated by this route.
INHALATION: (breathing) Not expected to be a hazard under normal operating conditions.
INGESTION: (swallowing) Ingestion of large quantities may cause the following: lnitation of digestive tract, signs of nervous system
depression, such as headache, drow~iness, dizziness, loss of coordination, fatigue, and nausea.
SECTION IV - SPECIAL PROTECTION INFORMATION
VENTILATION: If current ventilation practices are not adequate to maintain airborne concentrations below established exposure limits
(see section I), additional ventilation or exhaust systems may be required.
RESPIRATORY PROTECTION: The use of respiratory protection is advised when concentrates exceed the established exposure limits
(see Section I). Depending on the airborne concentration use a respirator or gas mask with appropriate cartridges or canisters
(NIOSH approved) or supplied air.
PROTECTIVE GLOVES: The use of gloves impermeable to the specific material handled is advised to prevent possible irritation.
EYE PROTECTION: Approved eye protection to safeguard against potential eye contact, irritation or injury is recommended.
SECTION V - REACTIVITY DATA
STABILITY: Stable
INCOMPATffiILITY: (materials to avoid) This product is incompatible with: OXidizing agents, strong acids and bases
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition in the presence of air may yield carbon monoxide, carbon
dioxide.
HAZARDOUS POLYMERIZATION: Will not occur
I
SECTION VI - SPILL OR LEAK PROCEDURES
PRECAUTIONS IN CASE OF LEAK OR SPILL: Keep all sources of ignition and hot metal surfaces away from spillfrelease. Stay
upwind and away from spill/release. Isolate hazard area and limit entry to emergency crew only. Stop spill/release if it can be done
without risk. Wear appropriate protective equipment including respiratory protection as conditions warrant (see Section IV). Prevent
spilled material from entering sewers, storm drains, and natural waterways. Dike far ahead of spill for later recovery and disposal. Spilled
material may be absorbed by an appropriate absorbent. Notify fire authorities and appropriate federal, state, and local agencies. If
spill/release is excess of EPA reportable quantity, immediately notify the National Response Center. Phone 800-424-8802
WASTE DISPOSAL METHOD: Dispose of product in accordance with local, county, state, and federal regulations.
Page 1
12-990
"
·
f
(J.'
UTILITY MANUFACTURING CO., INC.
';:[~~7700 MAIN STREET, WESTBURY, NY 11590
.,~.
"0,.
MATERIAL SAFETY DATA SHEET
(516) 997-6300 - FAX # (516) 997-6345
PLASTI-SEAL PVC CLEAR GLOO REGULAR BODY SOLVENT CEMENT
SECTION VlI - STORAGE AND SPECIAL PRECAUTIONS
HANDLING AND STORAGE PRECAUTIONS: Do not get in eyes, skin or clothing. Do not breathe vapor mist or gas. Keep
containers tightly closed, cool, dry, and away from all sources of ignition, Use and store this product with adequate ventilation.
Avoid inhalation of vapors and personal contact with the product. Use good personal hygiene practices. Bond and ground
equipment when transferring to another container. "Empty" containers contain residue (liquid andlor vapor) and can be
dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, or other
sources of ignition. They may explode and cause injury and death. Empty drums should be completely drained, properly
bunged, and promptly shipped to the supplier or drum reconditioner. All other containers should be disposed of in an
environmental1y safe manner and in accordance with governmental regulations. Before working in or on tanks which contain or
has contained his product, refer to OSHA or ANSI Z49.1 regulations and other governmental and industrial references
pertaining to cleaning, repairing, welding, or other contemplated operations.
SECTION VIII - FIRE AND EXPLOSION HAZARD DATA
EXTINGUISIDNG MEDIA: Extinguish with dry chemical, CO2, or a universal type foam.
FIRE AND EXPLOSION HAZARD: May decompose during contact with flames, heating elements, or in combustion engines releasing
irritating gases. Container may explode if heated due to resulting pressure rise.
FIRE FIGHTING PROCEDURES: Wear appropriate protective equipment including respiratory protection as conditions warrant (see
Section IV). Stop spill/release if it can be done without risk. Water spray may be useful in minimizing or dispersing vapors and
cooling equipment exposed to heat and flame. Avoid spreading burning liquid with water used for cooling purposes,
, SECTION IX - PHYSICAL DATA
ApPROXIMATE BOILING POINT (DEG F); >200
SPECIFICGRAVITY(68F), >1
RELATIVE EVAPORA TlON RATE (ESTIMATED): <I
VAPOR PRESSURE @20C mmHg (CALCULATED): <1
PER CENT VOLATILE: >80
FLASH POINT (TCC, DEG F): 24 (SOLVENT)
PER CENT SOLUBILITY IN WATER: 85
SECTION X - OTHER REGULATORY DATA
SECTION 302: NONE
SECTION 311 & 312: ACUTE, CHRONIC, FIRE
SECTION 313: See Section I.I
All components are in full compliance
with the TSCA inventory.
Waste material would be a DOOI
Health:
Flammability:
Reactivity:
3
3
o
CALIFORNIA PROPOSITION 65
NOT LISTED
CERCLA
TETRAHYDROFURANRQ: 1000LBS.
METHYL ETHYL KETONE RQ: 5000 LBS.
CYCLOHEXANONE RQ: 5000 LBS.
CARCINOGENICITY:
NOT LISTED with NTP or IARC.
The supplier disclaims all expressed or implied warranties of merchantability or fitness for a specific use, with respect to the product or the infonnation
provided herein, except for confonnation to contracted specifications. All information appearing herein is based upon data obtained from manufactures
and/or recognized technical sources, While the infonnation is believed to be accurate, we make no representations as to its accuracy or sufficiency,
Conditions of use are beyond our control, and therefore users are responsible for verifying the data under their own operating conditions to determine
whether the product is suitable for their particular purposes and they assume risks of their use, handling, and disposal of the product. Users also assume all
risks in regards to the publication or use of, or reliance upon, infonnation contained herein. This infonnation relates only to the product designated herein,
and does not relate to its use in combination with any other material or process.
Page 2
12-990
I
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement